OMAP3 : Fix McSPI RX Timeout
PATCH 1/1 OMAP3 : Fix McSPI RX Timeout
McSPI RX timeout issues are reported on some of the OMAP3 custom boards.
After verifying configuration sequence in TRM, there seems to be issue with McSPI configuration sequence.
The steps to be followed for both TX and RX:
1. Configure OMAP2_MCSPI_CHCONF0 register with required settings such as TX/RX mode, word length, force chip select(if required).
2. Set MS bit to 0 in OMAP2_MCSPI_CHCTRL0 register to provide the clock.
3. Enable SPI channel in OMAP2_MCSPI_MODULCTRL
But, the sequence used in current code seems to be wrong. Here it is:
1. Set MS bit to 0 in OMAP2_MCSPI_CHCTRL0 register to provide the clock (This is done during bootup)
2. Enable SPI channel in OMAP2_MCSPI_MODULCTRL
3. Configure OMAP2_MCSPI_CHCONF0 register with required settings such as TX/RX mode, word length, force chip select(if required).
After correcting configuration sequence, the timeout seems to be not reproducible anymore.
--- drivers/spi/omap2_mcspi.c | 4 +++- 1 files changed, 3 insertions(+), 1 deletions(-)
drivers/spi/omap2_mcspi.c +3 -1
@@ -802,7 +802,6 @@ static void omap2_mcspi_work(struct work_struct *work) spi = m->spi; cs = spi->controller_state; -omap2_mcspi_set_enable (spi,1 );list_for_each_entry (t, &m->transfers, transfer_list) {if (t->tx_buf ==NULL && t->rx_buf ==NULL && t->len) { status = -EINVAL ;
@@ -830,6 +829,9 @@ static void omap2_mcspi_work(struct work_struct *work) chconf |=OMAP2_MCSPI_CHCONF_TRM_TX_ONLY ;mcspi_write_chconf0 (spi, chconf); +omap2_mcspi_set_master_mode (mcspi->master); + +omap2_mcspi_set_enable (spi,1 );if (t->len) {unsigned count;
Signature · 1 line
1.6.0.4
Quoted 18 lines · * [email protected] <[email protected]> [091005 23:42]:
McSPI RX timeout issues are reported on some of the OMAP3 custom boards.
After verifying configuration sequence in TRM, there seems to be issue with McSPI configuration sequence.
The steps to be followed for both TX and RX:
1. ConfigureOMAP2_MCSPI_CHCONF0register with required settings such as TX/RX mode, word length, force chip select(if required).
2. Set MS bit to 0 inOMAP2_MCSPI_CHCTRL0register to provide the clock.
3. Enable SPI channel inOMAP2_MCSPI_MODULCTRLBut, the sequence used in current code seems to be wrong. Here it is:
1. Set MS bit to 0 inOMAP2_MCSPI_CHCTRL0register to provide the clock (This is done during bootup)
2. Enable SPI channel inOMAP2_MCSPI_MODULCTRL
3. ConfigureOMAP2_MCSPI_CHCONF0register with required settings such as TX/RX mode, word length, force chip select(if required).
Quoted 2 lines
After correcting configuration sequence, the timeout seems to be not reproducible anymore.
Please resend this to the right lists one for merging:
$ grep -A7 "SPI SUBSYSTEM" MAINTAINERS SPI SUBSYSTEM M: David Brownell <[email protected]> L: [email protected] S: Maintained F: Documentation/spi/ F: drivers/spi/ F: include/linux/spi/
Please also Cc linux-omap list too so people can easily keep track of it.
Regards,
Tony
Quoted 35 lines
Signed-off-by Manjunatha GK <[email protected]>--- drivers/spi/omap2_mcspi.c | 4 +++- 1 files changed, 3 insertions(+), 1 deletions(-)drivers/spi/omap2_mcspi.c +3
-1@@ -802,7 +802,6 @@ static void omap2_mcspi_work(struct work_struct *work) spi = m->spi; cs = spi->controller_state; -omap2_mcspi_set_enable (spi,1 );list_for_each_entry (t, &m->transfers, transfer_list) {if (t->tx_buf ==NULL && t->rx_buf ==NULL && t->len) { status = -EINVAL ;@@ -830,6 +829,9 @@ static void omap2_mcspi_work(struct work_struct *work) chconf |=OMAP2_MCSPI_CHCONF_TRM_TX_ONLY ;mcspi_write_chconf0 (spi, chconf); +omap2_mcspi_set_master_mode (mcspi->master); + +omap2_mcspi_set_enable (spi,1 );if (t->len) {unsigned count;Signature · 6 lines
1.6.0.4 -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html