input/touchscreen: add S3C24XX SoC touchscreen input driver
Subsystems (3)
PATCH 1/1 input/touchscreen: add S3C24XX SoC touchscreen input driver
This touchscreen driver is for touchscreen controller on Samsung S3C2410/S3C2440 SoC chip. S3C2410/S3C2440 has the on chip touchscreen controller based on it's analog to digital converter(8-channel analog inputs, touchscreen uses 4 of them). This driver uses the exsiting S3C ADC driver to make the touchscreen controller of S3C2410/S3C2440 work well together with other ADC devices connected to the S3C24XX SoC chip.
The patch is created against kernel 2.6.32-rc4 and tested with S3C2440 SoC and Samsung LTE430WQ-F0C touchscreen.
--------------------------------------------------------
drivers/input/touchscreen/Makefile +1 -0
@@ -10,6 +10,7 @@ obj-$(CONFIG_TOUCHSCREEN_AD7879) += ad7879.o obj-$(CONFIG_TOUCHSCREEN_ADS7846) += ads7846.o obj-$(CONFIG_TOUCHSCREEN_ATMEL_TSADCC) += atmel_tsadcc.o +obj-$(CONFIG_TOUCHSCREEN_S3C24XX_TSADCC) += s3c24xx_tsadcc.o obj-$(CONFIG_TOUCHSCREEN_BITSY) += h3600_ts_input.o obj-$(CONFIG_TOUCHSCREEN_CORGI) += corgi_ts.o obj-$(CONFIG_TOUCHSCREEN_GUNZE) += gunze.o
drivers/input/touchscreen/Kconfig +13 -0
@@ -307,6 +307,19 @@ To compile this driver as a module, choose M here: the module will be called atmel_tsadcc. +config TOUCHSCREEN_S3C24XX_TSADCC + tristate "Samsung S3C24XX touchscreen input driver" + depends on ARCH_S3C2410 && S3C24XX_ADC && INPUT && INPUT_TOUCHSCREEN + select SERIO + help + Say Y here if you have a touchscreen connected to the ADC Controller + on your s3c2410/s3c2440 SoC. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called s3c24xx_tsadcc. + config TOUCHSCREEN_UCB1400 tristate "Philips UCB1400 touchscreen" depends on AC97_BUS
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +432 -0
432 lines not on this page · raw message
Dmitry Torokhov
maintainerPATCH 1/1 input/touchscreen: add S3C24XX SoC touchscreen input driver
Hi Shine,
Quoted 10 lines · Shine Liu
This touchscreen driver is for touchscreen controller on Samsung S3C2410/S3C2440 SoC chip. S3C2410/S3C2440 has the on chip touchscreen controller based on it's analog to digital
converter(8-channel analog inputs, touchscreen uses 4 of them). This driver uses the exsiting S3C ADC driver to make the touchscreen controller of S3C2410/S3C2440 work well together with other ADC devices connected to the S3C24XX SoC chip.The patch is created against kernel 2.6.32-rc4 and tested with S3C2440 SoC and Samsung LTE430WQ-F0C touchscreen.
So I understand there are questions whether this verson of driver should be merged, I'll let you guys workit it out. I think that filtering is better be left off to tslib since there are many more opportunities to do this kind of stuff in userspace.
Still, below some comments so that the next iteration of the driver does not have the same faults ;)
Quoted 3 lines
Signed-off-by Shine Liu <[email protected]>Signed-off-by Shine Liu <[email protected]>
Umm, is it the same person? Then one sign-off is enough ;)
Quoted 15 lines
--------------------------------------------------------
drivers/input/touchscreen/Makefile +1
-0@@ -10,6 +10,7 @@ obj-$(CONFIG_TOUCHSCREEN_AD7879) += ad7879.o obj-$(CONFIG_TOUCHSCREEN_ADS7846) += ads7846.o obj-$(CONFIG_TOUCHSCREEN_ATMEL_TSADCC) += atmel_tsadcc.o +obj-$(CONFIG_TOUCHSCREEN_S3C24XX_TSADCC) += s3c24xx_tsadcc.o obj-$(CONFIG_TOUCHSCREEN_BITSY) += h3600_ts_input.o obj-$(CONFIG_TOUCHSCREEN_CORGI) += corgi_ts.o obj-$(CONFIG_TOUCHSCREEN_GUNZE) += gunze.o
drivers/input/touchscreen/Kconfig line 313
Quoted 7 lines
drivers/input/touchscreen/Kconfig +4
-0@@ -307,6 +307,19 @@ To compile this driver as a module, choose M here: the module will be called atmel_tsadcc. +config TOUCHSCREEN_S3C24XX_TSADCC + tristate "Samsung S3C24XX touchscreen input driver" + depends on ARCH_S3C2410 && S3C24XX_ADC && INPUT && INPUT_TOUCHSCREEN + select SERIO
Why do you need SERIO? I don't see it being a serio driver.
Quoted 32 lines
drivers/input/touchscreen/Kconfig +9
-0+ help + Say Y here if you have a touchscreen connected to the ADC Controller + on your s3c2410/s3c2440 SoC. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called s3c24xx_tsadcc. + config TOUCHSCREEN_UCB1400 tristate "Philips UCB1400 touchscreen" depends on AC97_BUSdrivers/input/touchscreen/s3c24xx_tsadcc.c new file +17
-0@@ -0,0 +1,432 @@ +/* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2 of the License, or +* (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA +* +* Part of the code come from openmoko project. +*
drivers/input/touchscreen/s3c24xx_tsadcc.c line 27
Quoted 10 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +10
-0+* Shine Liu <[email protected]> +*/ + +#include <linux/errno.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/slab.h> +#include <linux/input.h> +#include <linux/init.h> +#include <linux/serio.h>
NO need to include this.
Quoted 34 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +34
-0+#include <linux/timer.h> +#include <linux/delay.h> +#include <linux/platform_device.h> +#include <linux/clk.h> +#include <linux/io.h> +#include <asm/irq.h> + +#include <mach/gpio.h> +#include <mach/regs-gpio.h> +#include <mach/hardware.h> +#include <plat/regs-adc.h> +#include <plat/adc.h> + + +MODULE_AUTHOR ("Shine Liu <[email protected]>" ); +MODULE_DESCRIPTION ("Samsung s3c24xx touchscreen driver" ); +MODULE_LICENSE ("GPL" ); + + +#define S3C24XX_TS_VERSION 0x0101 + +#define TSC_SLEEP (S3C2410_ADCTSC_PULL_UP_DISABLE | \ + S3C2410_ADCTSC_XY_PST(0)) + +#define WAIT4INT (x) (((x)<<8) | \ + S3C2410_ADCTSC_YM_SEN | \ + S3C2410_ADCTSC_YP_SEN | \ + S3C2410_ADCTSC_XP_SEN | \ + S3C2410_ADCTSC_XY_PST(3)) + +#define AUTO_XY (S3C2410_ADCTSC_PULL_UP_DISABLE | \ + S3C2410_ADCTSC_AUTO_PST | \ + S3C2410_ADCTSC_XY_PST(0)) +
drivers/input/touchscreen/s3c24xx_tsadcc.c line 71
Quoted 10 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +10
-0+#define TS_STATE_STANDBY 0/* initial state */ +#define TS_STATE_PRESSED 1 +#define TS_STATE_RELEASE_PENDING 2/* wait to confirm the up event */ +#define TS_STATE_RELEASE 3 + +#define TIME_RELEASE_PENDING (HZ / 20)/* about 50ms */ +#define TIME_NEXT_CONV ((HZ < 51)? 1 : HZ / 50)/* about 20ms */ + +static char *s3c24xx_ts_name ="Samsung s3c24xx TouchScreen" ; +static void __iomem *base_addr;
No chance of a second device? I'd put it in s3c24xx_ts anyway.
Quoted 7 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +7
-0+ + +/* +* Per-touchscreen data. +*/ + +struct s3c24xx_ts {
drivers/input/touchscreen/s3c24xx_tsadcc.c line 88
Quoted 10 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +10
-0+struct input_dev *dev; +struct s3c_adc_client *adc_client; +unsigned char is_down; +unsigned char state; +unsigned adc_selected; +unsigned int delay;/* register value for delay */ +unsigned int presc;/* register value for prescaler */ +}; + +static struct s3c24xx_ts ts;
Better use platform_set_drvdata and platform_get_drvdata instead of a global.
Quoted 30 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +30
-0+ + +/* +* Low level functions to config registers. +*/ +static inline void s3c24xx_ts_connect (void ) +{ +s3c2410_gpio_cfgpin (S3C2410_GPG (12 ),S3C2410_GPG12_XMON ); +s3c2410_gpio_cfgpin (S3C2410_GPG (13 ), S3C2410_GPG13_nXPON); +s3c2410_gpio_cfgpin (S3C2410_GPG (14 ),S3C2410_GPG14_YMON ); +s3c2410_gpio_cfgpin (S3C2410_GPG (15 ), S3C2410_GPG15_nYPON); +} + +static void s3c24xx_ts_start_adc_conversion (void ) +{ +pr_debug ("start_adc_conv ADCTSC: 0x%x" , +readl (base_addr +S3C2410_ADCTSC )); +writel (AUTO_XY , base_addr +S3C2410_ADCTSC ); +pr_debug (" ---> 0x%x" , +readl (base_addr +S3C2410_ADCTSC )); +s3c_adc_start (ts.adc_client,0 ,1 ); +pr_debug (" ---> 0x%x\n" , +readl (base_addr +S3C2410_ADCTSC )); +} + + +/* +* Event handling +*/ +
drivers/input/touchscreen/s3c24xx_tsadcc.c line 128
Quoted 10 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +10
-0+enum ts_input_event {IE_UP =0 ,IE_DOWN }; + +static void ts_input_report (int event,int coords[]) +{ + +if (event ==IE_DOWN ) { +input_report_abs (ts.dev,ABS_X , coords[0 ]); +input_report_abs (ts.dev,ABS_Y , coords[1 ]); +input_report_key (ts.dev,BTN_TOUCH ,1 ); +input_report_abs (ts.dev,ABS_PRESSURE ,1 );
No fake pressure events please.
drivers/input/touchscreen/s3c24xx_tsadcc.c line 130
Quoted 2 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +2
-0+ +pr_debug ("down (X:%03d, Y:%03d)\n" , coords[0 ], coords[1 ]);
Maybe use dev_dbg()?
Quoted 7 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +7
-0+ }else { +input_report_key (ts.dev,BTN_TOUCH ,0 ); +input_report_abs (ts.dev,ABS_PRESSURE ,0 ); +pr_debug ("up\n" ); + } + +input_sync (ts.dev);
drivers/input/touchscreen/s3c24xx_tsadcc.c line 147
Quoted 10 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +10
-0+} + + +/* +* Timer to process the UP event or to report the postion of DRAG +*/ + +static void ts_drag_pull_timer_f (unsigned long data); +static struct timer_list ts_drag_pull_timer = +TIMER_INITIALIZER (ts_drag_pull_timer_f,0 ,0 );
Move it to the device structure as well.
drivers/input/touchscreen/s3c24xx_tsadcc.c line 156
Quoted 9 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +9
-0+ +static void ts_drag_pull_timer_f (unsigned long data) +{ +unsigned long flags; +/* delay reporting the UP event to avoid jitter */ +static unsigned release_pending_counter =0 ; +pr_debug ("Timer called: is_down[%d] status[%d]\n" , ts.is_down, ts.state); + +local_irq_save (flags);
Is it really needed?
Quoted 70 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +70
-0+if (ts.state ==TS_STATE_RELEASE_PENDING ) { +if (release_pending_counter++ <1 ) { +/* jitter avoidance window: delay TIME_RELEASE_PENDING jfs */ +mod_timer (&ts_drag_pull_timer, jiffies +TIME_RELEASE_PENDING ); + }else { +/* no down event occurd during last delay */ + release_pending_counter =0 ; +ts_input_report (IE_UP ,NULL ); + ts.state =TS_STATE_RELEASE ; +writel (WAIT4INT (0 ), base_addr +S3C2410_ADCTSC ); + } +local_irq_restore (flags); +return ; + } + +/* ts.is_down should be true here */ +s3c24xx_ts_start_adc_conversion (); +local_irq_restore (flags); +} + + +/* +* ISR for the IRQ_TS +*/ + +static irqreturn_t stylus_updown (int irq,void *dev_id) +{ +unsigned long data0; +unsigned long data1; +unsigned long adctsc; +int event_type;/* 1 for down, 0 for up */ + +/* +* According to s3c2440 manual chap16: After Touch Screen +* Controller generates INT_TC, XY_PST must be set to [00] +*/ + adctsc =readl (base_addr +S3C2410_ADCTSC ); +writel (adctsc & ~(S3C2410_ADCTSC_XY_PST (3 )), base_addr +S3C2410_ADCTSC ); + data0 =readl (base_addr +S3C2410_ADCDAT0 ); + data1 =readl (base_addr +S3C2410_ADCDAT1 ); + event_type = (!(data0 &S3C2410_ADCDAT0_UPDOWN )) && + (!(data1 &S3C2410_ADCDAT0_UPDOWN )); +pr_debug ("event_type: %d, DATA0 0x%lx, DATA1 0x%lx, ADCTSC 0x%lx, " +"ADCUPDN 0x%x\n" , event_type, data0, data1, + adctsc,readl (base_addr +0x14 )); + +/* ignore sequential same event */ +if (ts.is_down == event_type) { +pr_debug ("###Ignore same event: %d\n" , event_type); +/* restore XY_PST */ +writel (adctsc, base_addr +S3C2410_ADCTSC ); +return IRQ_HANDLED ; + } + + ts.is_down = event_type; +if (ts.is_down) { +s3c24xx_ts_start_adc_conversion (); + }else { + ts.state =TS_STATE_RELEASE_PENDING ; +/* +* Delay to report the up event for a while to avoid jitter. +* This state will be checked after (0, TIME_NEXT_CONV) +* jiffies depended on when the interrupt occured. +*/ + } + +return IRQ_HANDLED ; +} + +/*
drivers/input/touchscreen/s3c24xx_tsadcc.c line 236
Quoted 10 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +10
-0+* Called in ISR of IRQ_ADC +*/ + +static void stylus_adc_action (struct s3c_adc_client *client, +unsigned p0,unsigned p1,unsigned *conv_left) +{ +int buf[2 ]; +unsigned long flags; + +local_irq_save (flags);
Why?
Quoted 32 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +32
-0+/* +* IRQ_TS may rise just in the time window between AUTO_XY mode +* set and this pointer */ +if (ts.state ==TS_STATE_RELEASE_PENDING ) + { +local_irq_restore (flags); +return ; + } + +/* Grab the ADC results. */ + buf[0 ] = p0; + buf[1 ] = p1; + +ts_input_report (IE_DOWN , buf); +pr_debug ("[adc_selected: %d] ADCTSC: 0x%x" , + ts.adc_selected,readl (base_addr +S3C2410_ADCTSC )); + +writel (WAIT4INT (1 ), base_addr +S3C2410_ADCTSC ); +printk (" ---> 0x%x\n" , +readl (base_addr +S3C2410_ADCTSC )); + + ts.state =TS_STATE_PRESSED ; +mod_timer (&ts_drag_pull_timer, jiffies +TIME_NEXT_CONV ); +local_irq_restore (flags); +} + + +/* +* callback function for s3c-adc +*/ + +void adc_selected_f (struct s3c_adc_client *client,unsigned selected)
drivers/input/touchscreen/s3c24xx_tsadcc.c line 278
Quoted 10 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +10
-0+{ + ts.adc_selected = selected; +} + + +/* +* The functions for inserting/removing us as a module. +*/ + +static int __init s3c24xx_ts_probe (struct platform_device *pdev)
__devinit.
Quoted 19 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +19
-0+{ +int rc; +struct input_dev *input_dev; +int ret =0 ; + +dev_info (&pdev->dev,"Starting\n" ); +pr_debug ("Entering s3c24xx_ts_probe\n" ); + + base_addr =ioremap (S3C2410_PA_ADC ,0x20 ); +if (base_addr ==NULL ) { +dev_err (&pdev->dev,"Failed to remap register block\n" ); + ret = -ENOMEM ; + goto fail0; + } + +/* Configure GPIOs */ +s3c24xx_ts_connect (); + +writel (WAIT4INT (0 ), base_addr +S3C2410_ADCTSC );
drivers/input/touchscreen/s3c24xx_tsadcc.c line 307
Quoted 10 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +10
-0+ +/* Initialise input stuff */ +memset (&ts,0 ,sizeof (struct s3c24xx_ts )); + ts.adc_client = +s3c_adc_register (pdev, adc_selected_f, stylus_adc_action,1 ); +if (!ts.adc_client) { +dev_err (&pdev->dev, +"Unable to register s3c24xx_ts as s3c_adc client\n" ); + ret = -EIO ; + goto fail1;
-EWIERDIDENTATION.
Quoted 11 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +11
-0+ } + +/* save prescale EN and VAL in the S3C2410_ADCCON register */ + ts.presc =readl (base_addr +S3C2410_ADCCON ); +/* save value of S3C2410_ADCDLY register */ + ts.delay =readl (base_addr +S3C2410_ADCDLY ); +pr_debug ("platform data: ADCCON=%08x ADCDLY=%08x\n" , ts.presc, ts.delay); + + input_dev =input_allocate_device (); +if (!input_dev) { +dev_err (&pdev->dev,"Unable to allocate the input device\n" );
drivers/input/touchscreen/s3c24xx_tsadcc.c line 328
Quoted 10 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +10
-0+ ret = -ENOMEM ; + goto fail2; + } + + ts.dev = input_dev; + ts.dev->evbit[0 ] =BIT_MASK (EV_SYN ) |BIT_MASK (EV_KEY ) |BIT_MASK (EV_ABS ); + ts.dev->keybit[BIT_WORD (BTN_TOUCH )] =BIT_MASK (BTN_TOUCH ); +input_set_abs_params (ts.dev,ABS_X ,0 ,0x3FF ,0 ,0 ); +input_set_abs_params (ts.dev,ABS_Y ,0 ,0x3FF ,0 ,0 ); +input_set_abs_params (ts.dev,ABS_PRESSURE ,0 ,1 ,0 ,0 );
Kill the above line.
drivers/input/touchscreen/s3c24xx_tsadcc.c line 331
Quoted 3 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +3
-0+ + ts.dev->name = s3c24xx_ts_name; + ts.dev->id.bustype =BUS_RS232 ;
Really?
Quoted 4 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +4
-0+ ts.dev->id.vendor =0xBAAD ; + ts.dev->id.product =0xBEEF ; + ts.dev->id.version =S3C24XX_TS_VERSION ; + ts.state =TS_STATE_STANDBY ;
drivers/input/touchscreen/s3c24xx_tsadcc.c line 345
Quoted 10 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +10
-0+ +/* Get IRQ */ +if (request_irq (IRQ_TC , stylus_updown,IRQF_SAMPLE_RANDOM , +"s3c24xx_ts_action" , ts.dev)) { +dev_err (&pdev->dev,"Could not allocate ts IRQ_TC !\n" ); + ret = -EIO ; + goto fail3; + } + +dev_info (&pdev->dev,"Successfully loaded\n" );
No need.
drivers/input/touchscreen/s3c24xx_tsadcc.c line 356
Quoted 11 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +11
-0+ +/* All went ok, so register to the input system */ + rc =input_register_device (ts.dev); +if (rc) { + ret = -EIO ; + goto fail4; + } +return 0 ; + +fail4: +disable_irq (IRQ_TC );
No need.
drivers/input/touchscreen/s3c24xx_tsadcc.c line 368
Quoted 12 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +12
-0+free_irq (IRQ_TC , ts.dev); +fail3: +input_free_device (ts.dev); +fail2: +s3c_adc_release (ts.adc_client); +fail1: +iounmap (base_addr); +fail0: +return ret; +} + +static int s3c24xx_ts_remove (struct platform_device *pdev)
__devexit.
drivers/input/touchscreen/s3c24xx_tsadcc.c line 370
Quoted 2 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +2
-0+{ +disable_irq (IRQ_TC );
No need.
drivers/input/touchscreen/s3c24xx_tsadcc.c line 373
Quoted 3 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +3
-0+free_irq (IRQ_TC , ts.dev); +input_unregister_device (ts.dev); +input_free_device (ts.dev);
No free after unregister, input_dev is refcounted.
Quoted 29 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +29
-0+s3c_adc_release (ts.adc_client); +iounmap (base_addr); +return 0 ; +} + +#ifdef CONFIG_PM +static int s3c24xx_ts_suspend (struct platform_device *pdev,pm_message_t state) +{ +disable_irq (IRQ_TC ); + ts.presc =readl (base_addr +S3C2410_ADCCON ); + ts.delay =readl (base_addr +S3C2410_ADCDLY ); + +writel (TSC_SLEEP , base_addr +S3C2410_ADCTSC ); +writel (ts.presc |S3C2410_ADCCON_STDBM , base_addr +S3C2410_ADCCON ); +return 0 ; +} + +static int s3c24xx_ts_resume (struct platform_device *pdev) +{ +/* Restore registers */ +writel (ts.presc, base_addr +S3C2410_ADCCON ); +writel (ts.delay, base_addr +S3C2410_ADCDLY ); +writel (WAIT4INT (0 ), base_addr +S3C2410_ADCTSC ); +enable_irq (IRQ_TC ); +return 0 ; +} + +#else +#define s3c24xx_ts_suspend NULL
drivers/input/touchscreen/s3c24xx_tsadcc.c line 412
Quoted 10 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +10
-0+#define s3c24xx_ts_resume NULL +#endif + +static struct platform_driver s3c24xx_ts_driver = { + .driver = { + .name ="s3c24xx-ts" , + .owner =THIS_MODULE , + }, + .probe = s3c24xx_ts_probe, + .remove = s3c24xx_ts_remove,
__devexit_p().
drivers/input/touchscreen/s3c24xx_tsadcc.c line 413
Quoted 1 line
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +1
-0+ .suspend = s3c24xx_ts_suspend,
This should be converted to dev_pm_ops.
drivers/input/touchscreen/s3c24xx_tsadcc.c line 422
Quoted 9 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +9
-0+ .resume = s3c24xx_ts_resume, +}; + +static int __init s3c24xx_ts_init (void ) +{ +int rc; + + rc =platform_driver_register (&s3c24xx_ts_driver); +return rc;
Just do "return platform_driver_register();"
drivers/input/touchscreen/s3c24xx_tsadcc.c line 432
Quoted 10 lines
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +10
-0+} + +static void __exit s3c24xx_ts_exit(void) +{ +platform_driver_unregister (&s3c24xx_ts_driver); +} + +module_init (s3c24xx_ts_init); +module_exit (s3c24xx_ts_exit); +
Thanks.
Signature · 1 line
Dmitry
PATCH v2 1/1 input/touchscreen: add S3C24XX SoC touchscreen input driver
Hi Dmitry,
Quoted 3 lines · Dmitry Torokhov
Still, below some comments so that the next iteration of the driver does not have the same faults ;)
Thank you for your carefully review. I have removed the unnecessary code according your comment. And I also removed some redundant head files in the include section. The error handling in s3c24xx_ts_probe was also improved.
I'm very glad to hear any further comment on this patch.
Best Regards,
Shine Liu
-----------------------------------------------------
drivers/input/touchscreen/Kconfig +12 -0
@@ -307,6 +307,18 @@ To compile this driver as a module, choose M here: the module will be called atmel_tsadcc. +config TOUCHSCREEN_S3C24XX_TSADCC + tristate "Samsung S3C24XX touchscreen input driver" + depends on ARCH_S3C2410 && S3C24XX_ADC && INPUT && INPUT_TOUCHSCREEN + help + Say Y here if you have a touchscreen connected to the ADC Controller + on your s3c2410/s3c2440 SoC. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called s3c24xx_tsadcc. + config TOUCHSCREEN_UCB1400 tristate "Philips UCB1400 touchscreen" depends on AC97_BUS
input/touchscreen/Makefile +1 -0
@@ -10,6 +10,7 @@ obj-$(CONFIG_TOUCHSCREEN_AD7879) += ad7879.o obj-$(CONFIG_TOUCHSCREEN_ADS7846) += ads7846.o obj-$(CONFIG_TOUCHSCREEN_ATMEL_TSADCC) += atmel_tsadcc.o +obj-$(CONFIG_TOUCHSCREEN_S3C24XX_TSADCC) += s3c24xx_tsadcc.o obj-$(CONFIG_TOUCHSCREEN_BITSY) += h3600_ts_input.o obj-$(CONFIG_TOUCHSCREEN_CORGI) += corgi_ts.o obj-$(CONFIG_TOUCHSCREEN_GUNZE) += gunze.o
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +440 -0
440 lines not on this page · raw message
PATCH v2 1/1 input/touchscreen: add S3C24XX SoC touchscreen input driver
In reply to Dmitry Torokhov[re-CC to linux-arm-kernel at lists.infradead.org]
----
Hi Dmitry,
Quoted 3 lines · Dmitry Torokhov
Still, below some comments so that the next iteration of the driver does not have the same faults ;)
Thank you for your carefully review. I have removed the unnecessary code according your comment. And I also removed some redundant head files in the include section. The error handling in s3c24xx_ts_probe was also improved.
I'm very glad to hear any further comment on this patch.
Best Regards,
Shine Liu
-----------------------------------------------------
drivers/input/touchscreen/Kconfig +12 -0
@@ -307,6 +307,18 @@ To compile this driver as a module, choose M here: the module will be called atmel_tsadcc. +config TOUCHSCREEN_S3C24XX_TSADCC + tristate "Samsung S3C24XX touchscreen input driver" + depends on ARCH_S3C2410 && S3C24XX_ADC && INPUT && INPUT_TOUCHSCREEN + help + Say Y here if you have a touchscreen connected to the ADC Controller + on your s3c2410/s3c2440 SoC. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called s3c24xx_tsadcc. + config TOUCHSCREEN_UCB1400 tristate "Philips UCB1400 touchscreen" depends on AC97_BUS
input/touchscreen/Makefile +1 -0
@@ -10,6 +10,7 @@ obj-$(CONFIG_TOUCHSCREEN_AD7879) += ad7879.o obj-$(CONFIG_TOUCHSCREEN_ADS7846) += ads7846.o obj-$(CONFIG_TOUCHSCREEN_ATMEL_TSADCC) += atmel_tsadcc.o +obj-$(CONFIG_TOUCHSCREEN_S3C24XX_TSADCC) += s3c24xx_tsadcc.o obj-$(CONFIG_TOUCHSCREEN_BITSY) += h3600_ts_input.o obj-$(CONFIG_TOUCHSCREEN_CORGI) += corgi_ts.o obj-$(CONFIG_TOUCHSCREEN_GUNZE) += gunze.o
drivers/input/touchscreen/s3c24xx_tsadcc.c new file +440 -0
440 lines not on this page · raw message