DSS2 clocking
I'm using DSS2, currently just with a frame buffer to a [VGA/RGB] monitor.
I'm trying to understand how to set the timing parameters for my device. The simple 'omapfb.mode=1024x768-24@75' doesn't quite cut it for some of the devices I need to use.
Questions:
* How can I get different pixel clocks? I seem to always end up with 61714285:
# cat /tmp/dbg/omapdss/clk
- dss -
internal clk count 2
dss_ick 83000000 1
dss1_alwon_fck 123428570 1
dss2_alwon_fck 13000000 0
dss_tv_fck 54000000 0
dss_96m_fck 96000000 0
- dispc -
dispc fclk source = dss1_alwon_fclk
pixel clk = 123428570 / 1 / 2 = 61714285
* How can I control the waveform? In particular, the
size and shape of the "porches"? My display seems to
need these settings:
61714,1024/26/162/136,768/3/29/6
I'd like to get this behaviour, either from the boot line
or ideally by default.
* The display also seems to want the sync pulses to be
asserted low (inverted?). Currently, I have this "hard-wired"
into my display device, but I'd also like this to be adjustable.Thanks for any pointers, etc.
Note: I'm using Tomi's tree from roughly late July
http://www.bat.org/~tomba/git/linux-omap-dss.git
7ae220f46384b34e72b8c3b0c2075a674a3f74fe
Thanks for any pointers
Signature · 4 lines
------------------------------------------------------------ Gary Thomas | Consulting for the MLB Associates | Embedded world ------------------------------------------------------------
Hi,
Quoted 11 lines · ext Gary Thomas
I'm using DSS2, currently just with a frame buffer to a [VGA/RGB] monitor.
I'm trying to understand how to set the timing parameters for my device. The simple 'omapfb.mode=1024x768-24@75' doesn't quite cut it for some of the devices I need to use.
Questions:
* How can I get different pixel clocks? I seem to alwaysend up with 61714285:
The pixel clock is calculated based on the given resolution and refresh rate. You can adjust it via sysfs. But you don't have very fine graded control when using the normal pixel clock source. When using DSI PLL to generate the DISPC functional clock, you can get much more exact pixel clock. But DSI PLL support is quite experimental.
Quoted 9 lines
# cat /tmp/dbg/omapdss/clk
- dss -
internal clk count 2
dss_ick 83000000 1
dss1_alwon_fck 123428570 1
dss2_alwon_fck 13000000 0
dss_tv_fck 54000000 0
dss_96m_fck 96000000 0
- dispc -Quoted 8 lines
dispc fclk source = dss1_alwon_fclk
pixel clk = 123428570 / 1 / 2 = 61714285
* How can I control the waveform? In particular, the
size and shape of the "porches"? My display seems to
need these settings:
61714,1024/26/162/136,768/3/29/6
I'd like to get this behaviour, either from the boot line
or ideally by default.Currently you cannot set these via kernel arguments, only via sysfs or in the panel driver.
Quoted 3 lines
* The display also seems to want the sync pulses to be asserted low (inverted?). Currently, I have this "hard-wired" into my display device, but I'd also like this to be adjustable.
These cannot currently be changed at all, they can only be defined in the panel driver.
Tomi