omap3evm : enable nand support
Subsystems (3)
PATCH 1/1 omap3evm : enable nand support
Enable Nand suport on the OMAP3EVM.
Signed-off-by Sriramakrishnan <[email protected]>
---
This patch has been generated against the tip of for-next branch.
arch/arm/configs/omap3_evm_defconfig | 2 + arch/arm/mach-omap2/board-omap3evm.c | 102 ++++++++++++++++++++++++++++++++++ 2 files changed, 104 insertions(+), 0 deletions(-)
arch/arm/configs/omap3_evm_defconfig +2 -0
@@ -516,6 +516,8 @@ CONFIG_MTD_NAND=y # CONFIG_MTD_NAND_ECC_SMC is not set # CONFIG_MTD_NAND_MUSEUM_IDS is not set # CONFIG_MTD_NAND_GPIO is not set +CONFIG_MTD_NAND_OMAP2=y +# CONFIG_MTD_NAND_OMAP_PREFETCH is not set CONFIG_MTD_NAND_IDS=y # CONFIG_MTD_NAND_DISKONCHIP is not set # CONFIG_MTD_NAND_NANDSIM is not set
arch/arm/mach-omap2/board-omap3evm.c +102 -0
132 lines not on this page · raw message
Signature · 1 line
1.6.2.4
Tony Lindgren
maintainerHi,
Quoted 10 lines · Sriramakrishnan
Enable Nand suport on the OMAP3EVM.
Signed-off-by Sriramakrishnan <[email protected]>---
This patch has been generated against the tip of for-next branch.arch/arm/configs/omap3_evm_defconfig | 2 + arch/arm/mach-omap2/board-omap3evm.c | 102 ++++++++++++++++++++++++++++++++++ 2 files changed, 104 insertions(+), 0 deletions(-)
<snip>
Quoted 25 lines
arch/arm/mach-omap2/board-omap3evm.c +25
-0+void __init omap3evm_flash_init (void ) +{ +u8 cs =0 ; +u8 nandcs =GPMC_CS_NUM +1 ; +u32 gpmc_base_add =OMAP34XX_GPMC_VIRT ; + +while (cs <GPMC_CS_NUM ) { +u32 ret =0 ; + ret =gpmc_cs_read_reg (cs,GPMC_CS_CONFIG1 ); + +if ((ret &0xC00 ) ==0x800 ) { +/* Found it!! */ +if (nandcs >GPMC_CS_NUM ) + nandcs = cs; + } + cs++; + } +if (nandcs >GPMC_CS_NUM ) { +printk (KERN_INFO "NAND: Unable to find configuration " +" in GPMC\n " ); +return ; + } + +if (nandcs <GPMC_CS_NUM ) { + omap3evm_nand_data.cs = nandcs;
arch/arm/mach-omap2/board-omap3evm.c line 154
Quoted 10 lines
arch/arm/mach-omap2/board-omap3evm.c +10
-0+ omap3evm_nand_data.gpmc_cs_baseaddr = (void *)(gpmc_base_add + +GPMC_CS0_BASE + nandcs*GPMC_CS_SIZE ); + omap3evm_nand_data.gpmc_baseaddr = (void *) (gpmc_base_add); + +if (platform_device_register (&omap3evm_nand_device) <0 ) { +printk (KERN_ERR "Unable to register NAND device\n" ); + } + } +} +
To me it looks like this should work with the sdp-flash.c once the flash detection code is done in a clean way.
Not adding yet more cut and paste hacks, please coordinate within TI on adding the flash detection in a sane way.
Regards,
Tony