Skip to contentSkip to conversation

iw: display noise level from survey data

PATCH In review Holger Schurig 2 participants 3 messages Nov 11, 2009 Kbuild

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 iw: display noise level from survey data

Sample output:

# iw dev wlan0 survey dump
Survey data from wlan0
        frequency:      2412 MHz
        noise:          -92 dBm
Makefile +1 -1
@@ -15,7 +15,7 @@
 CFLAGS += -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -Werror-implicit-function-declaration
 
 OBJS = iw.o genl.o event.o info.o phy.o \
-	interface.o ibss.o station.o util.o \
+	interface.o ibss.o station.o survey.o util.o \
 	mesh.o mpath.o scan.o reg.o version.o \
 	reason.o status.o connect.o link.o
 OBJS += sections.o
survey.c new file +66 -0

66 lines not on this page · raw message

nl80211.h +34 -0
@@ -160,6 +160,11 @@
  * @NL80211_CMD_SCAN_ABORTED: scan was aborted, for unspecified reasons,
  *	partial scan results may be available
  *
+ * @NL80211_CMD_GET_SURVEY: get survey resuls, e.g. channel occupation
+ *      or noise level
+ * @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to
+ *	NL80211_CMD_GET_SURVEY and on the "scan" multicast group)
+ *
  * @NL80211_CMD_REG_CHANGE: indicates to userspace the regulatory domain
  * 	has been changed and provides details of the request information
  * 	that caused the change such as who initiated the regulatory request
@@ -341,6 +346,9 @@
 
 	NL80211_CMD_SET_WIPHY_NETNS,
 
+	NL80211_CMD_GET_SURVEY,
+	NL80211_CMD_NEW_SURVEY_RESULTS,
+
 	/* add new commands above here */
 
 	/* used to define NL80211_CMD_MAX below */
@@ -584,6 +592,10 @@
  *	changed then the list changed and the dump should be repeated
  *	completely from scratch.
  *
+ * @NL80211_ATTR_SURVEY_INFO: survey information about a channel, part of
+ *      the survey response for %NL80211_CMD_GET_SURVEY, nested attribute
+ *      containing info as possible, see &enum survey_info.
+ *
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
  */
@@ -714,6 +726,8 @@
 
 	NL80211_ATTR_PID,
 
+	NL80211_ATTR_SURVEY_INFO,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,
@@ -1117,6 +1131,26 @@
 };
 
 /**
+ * enum nl80211_survey_info - survey information
+ *
+ * These attribute types are used with %NL80211_ATTR_SURVEY_INFO
+ * when getting information about a survey.
+ *
+ * @__NL80211_SURVEY_INFO_INVALID: attribute number 0 is reserved
+ * @NL80211_SURVEY_INFO_FREQUENCY: center frequency of channel
+ * @NL80211_SURVEY_INFO_NOISE: noise level of channel (u8, dBm)
+ */
+enum nl80211_survey_info {
+	__NL80211_SURVEY_INFO_INVALID,
+	NL80211_SURVEY_INFO_FREQUENCY,
+	NL80211_SURVEY_INFO_NOISE,
+
+	/* keep last */
+	__NL80211_SURVEY_INFO_AFTER_LAST,
+	NL80211_SURVEY_INFO_MAX = __NL80211_SURVEY_INFO_AFTER_LAST - 1
+};
+
+/**
  * enum nl80211_mntr_flags - monitor configuration flags
  *
  * Monitor configuration flags.
Signature · 1 line
http://www.holgerschurig.de
#1 lore raw

This no longer works against wireless-testing, because some NL80211_ATTR_SURVEY_INFO has changed the number from 53 to 54 (in wireless-testing). So before/after appyling, nl80211.h should be harmonized between iw and wireless-testing.

Signature · 1 line
http://www.holgerschurig.de
#2 lore raw
Quoted 4 lines · Holger Schurig

This no longer works against wireless-testing, because some NL80211_ATTR_SURVEY_INFO has changed the number from 53 to 54 (in wireless-testing). So before/after appyling, nl80211.h should be harmonized between iw and wireless-testing.

I tend to copy it over before applying new patches, so feel free to send patches w/o nl80211.h changes included (but I can deal with this too).

johannes