p54: software hot-swap eeprom image
Subsystems (3)
RFC 1/1 p54: software hot-swap eeprom image
This (aggregated) patch adds a new sysfs file "eeprom_overwrite" which can be used to upload an customized eeprom image to the driver during normal operation.
The old wlanX device will quickly vanish. And if the new EEPROM image passes all sanity checks the device will reappear.
Hopefully, this proves to be an adequate solution for everyone with a bad/missing EEPROM data/chip.
---
there are plenty of bugs left!
would be nice to hear from p54spi & p54pci folks!
Regards,
Chr
---
drivers/net/wireless/p54/eeprom.c +167 -36
@@ -121,25 +121,20 @@ static int p54_generate_band(struct ieee80211_hw *dev, enum ieee80211_band band) {struct p54_common *priv = dev->priv; -struct ieee80211_supported_band *tmp, *old; +struct ieee80211_supported_band *old_band, *new_band; +struct ieee80211_channel *tmp, *old_chan, *new_chan;unsigned int i, j; -int ret = -ENOMEM ; +int old_chan_num, ret =0 ;if ((!list->entries) || (!list->band_channel_num[band]))return -EINVAL ; - tmp =kzalloc (sizeof (*tmp),GFP_KERNEL ); -if (!tmp) - goto err_out; - - tmp->channels =kzalloc (sizeof (struct ieee80211_channel ) * - list->band_channel_num[band],GFP_KERNEL ); -if (!tmp->channels) - goto err_out; - - ret =p54_fill_band_bitrates (dev, tmp, band); -if (ret) - goto err_out; + tmp =kzalloc (sizeof (struct ieee80211_channel ) * + list->band_channel_num[band],GFP_KERNEL ); +if (!tmp) { + ret = -ENOMEM ; + goto out; + }for (i =0 , j =0 ; (j < list->band_channel_num[band]) && (i < list->entries); i++) {
@@ -161,8 +156,8 @@ static int p54_generate_band(struct ieee80211_hw *dev,continue ; } - tmp->channels[j].band = list->channels[i].band; - tmp->channels[j].center_freq = list->channels[i].freq; + tmp[j].band = list->channels[i].band; + tmp[j].center_freq = list->channels[i].freq; j++; }
@@ -172,25 +167,60 @@ static int p54_generate_band(struct ieee80211_hw *dev, "2 GHz" : "5 GHz"); ret = -ENODATA ; - goto err_out; + goto out; } - tmp->n_channels = j; - old = priv->band_table[band]; - priv->band_table[band] = tmp; -if (old) { -kfree (old->channels); -kfree (old); + old_band = priv->band_table[band]; +if (old_band) { + old_chan_num = old_band->n_channels; + old_chan = old_band->channels; + old_band->n_channels =0 ; + old_band->n_bitrates =0 ; + }else { + old_chan_num =0 ; + old_chan =NULL ; } -return 0 ; +if (j < old_chan_num) { +printk (KERN_ERR "%s: Channel list can only be extended.\n" , +wiphy_name (dev->wiphy)); + goto out; + } + + new_band =krealloc (old_band,sizeof (*new_band),GFP_KERNEL ); +if (!new_band) { +printk (KERN_ERR "%s: Unable to modify band table.\n" , +wiphy_name (dev->wiphy)); + + goto out; + } + + new_band->band = band; + new_band->ht_cap.ht_supported = false; -err_out: -if (tmp) { -kfree (tmp->channels); -kfree (tmp); + new_chan =krealloc (old_chan, j *sizeof (struct ieee80211_channel ), +GFP_KERNEL ); + +if (!new_chan) { +printk (KERN_ERR "%s: Unable to modify band channel table.\n" , +wiphy_name (dev->wiphy)); + + goto out; } +memcpy (new_chan, tmp, j *sizeof (struct ieee80211_channel )); + + new_band->channels = new_chan; + new_band->n_channels = j; + + ret =p54_fill_band_bitrates (dev, new_band, band); +if (ret) + goto out; + + priv->band_table[band] = new_band; + +out: +kfree (tmp);return ret; }
@@ -533,7 +563,19 @@ static struct p54_cal_database *p54_convert_db(struct pda_custom_wrapper *src,return dst; } -int p54_parse_eeprom (struct ieee80211_hw *dev,void *eeprom,int len) +static void p54_reset_phydata (struct p54_common *priv) +{ +memset (&priv->rssical_db,0 ,sizeof (priv->rssical_db)); + priv->iq_autocal_len =0 ; +kfree (priv->output_limit); +kfree (priv->curve_data); +kfree (priv->iq_autocal); + priv->output_limit =NULL ; + priv->curve_data =NULL ; + priv->iq_autocal =NULL ; +} + +int p54_parse_eeprom (struct ieee80211_hw *dev,const void *eeprom,int len) {struct p54_common *priv = dev->priv;struct eeprom_pda_wrap *wrap;
@@ -543,10 +585,14 @@ int p54_parse_eeprom(struct ieee80211_hw *dev, void *eeprom, int len)int err;u8 *end = (u8 *)eeprom + len;u16 synth =0 ; +bool has_rssical = false, has_mac = false, has_country = false; wrap = (struct eeprom_pda_wrap *) eeprom; entry = (void *)wrap->data +le16_to_cpu (wrap->len); +mutex_lock (&priv->conf_mutex); +p54_reset_phydata (priv); +/* verify that at least the entry length/code fits */ while ((u8 *)entry <= end -sizeof (*entry)) { entry_len =le16_to_cpu (entry->len);
@@ -558,21 +604,34 @@ int p54_parse_eeprom(struct ieee80211_hw *dev, void *eeprom, int len)switch (le16_to_cpu (entry->code)) {case PDR_MAC_ADDRESS : +if (has_mac) +break ; + + has_mac = true; +if (data_len !=ETH_ALEN )break ; +SET_IEEE80211_PERM_ADDR (dev, entry->data);break ; +case PDR_PRISM_PA_CAL_OUTPUT_POWER_LIMITS :if (priv->output_limit)break ; + err =p54_convert_output_limits (dev, entry->data, data_len);if (err) goto err;break ; +case PDR_PRISM_PA_CAL_CURVE_DATA : {struct pda_pa_curve_data *curve_data = (struct pda_pa_curve_data *)entry->data; + +if (priv->curve_data) +break ; +if (data_len <sizeof (*curve_data)) { err = -EINVAL ; goto err;
@@ -597,7 +656,11 @@ int p54_parse_eeprom(struct ieee80211_hw *dev, void *eeprom, int len) goto err; }break ; +case PDR_PRISM_ZIF_TX_IQ_CALIBRATION : +if (priv->iq_autocal) +break ; + priv->iq_autocal =kmalloc (data_len,GFP_KERNEL );if (!priv->iq_autocal) { err = -ENOMEM ;
@@ -607,11 +670,22 @@ int p54_parse_eeprom(struct ieee80211_hw *dev, void *eeprom, int len)memcpy (priv->iq_autocal, entry->data, data_len); priv->iq_autocal_len = data_len /sizeof (struct pda_iq_autocal_entry );break ; +case PDR_DEFAULT_COUNTRY : +if (has_country) +break ; + + has_country = true; +p54_parse_default_country (dev, entry->data, data_len);break ; +case PDR_INTERFACE_LIST : tmp = entry->data; + +if (synth) +break ; +while ((u8 *)tmp < entry->data + data_len) {struct exp_if *exp_if = tmp;if (exp_if->if_id ==cpu_to_le16 (IF_ID_ISL39000 ))
@@ -619,22 +693,38 @@ int p54_parse_eeprom(struct ieee80211_hw *dev, void *eeprom, int len) tmp +=sizeof (*exp_if); }break ; +case PDR_HARDWARE_PLATFORM_COMPONENT_ID : +if (priv->version) +break ; +if (data_len <2 )break ; priv->version = *(u8 *)(entry->data +1 );break ; +case PDR_RSSI_LINEAR_APPROXIMATION :case PDR_RSSI_LINEAR_APPROXIMATION_DUAL_BAND :case PDR_RSSI_LINEAR_APPROXIMATION_EXTENDED : +if (has_rssical) +break ; + + has_rssical = true; +p54_parse_rssical (dev, entry->data, data_len,le16_to_cpu (entry->code));break ; +case PDR_RSSI_LINEAR_APPROXIMATION_CUSTOM : {__le16 *src = (void *) entry->data;s16 *dst = (void *) &priv->rssical_db;int i; +if (has_rssical) +break ; + + has_rssical = true; +if (data_len !=sizeof (priv->rssical_db)) { err = -EINVAL ; goto err;
@@ -644,24 +734,30 @@ int p54_parse_eeprom(struct ieee80211_hw *dev, void *eeprom, int len) *(dst++) = (s16 )le16_to_cpu (*(src++)); }break ; +case PDR_PRISM_PA_CAL_OUTPUT_POWER_LIMITS_CUSTOM : {struct pda_custom_wrapper *pda = (void *) entry->data;if (priv->output_limit || data_len <sizeof (*pda))break ; + priv->output_limit =p54_convert_db (pda, data_len); }break ; +case PDR_PRISM_PA_CAL_CURVE_DATA_CUSTOM : {struct pda_custom_wrapper *pda = (void *) entry->data;if (priv->curve_data || data_len <sizeof (*pda))break ; + priv->curve_data =p54_convert_db (pda, data_len); }break ; +case PDR_END :/* make it overrun */ entry_len = len;break ; +default :break ; }
@@ -670,7 +766,11 @@ int p54_parse_eeprom(struct ieee80211_hw *dev, void *eeprom, int len) }if (!synth || !priv->iq_autocal || !priv->output_limit || - !priv->curve_data) { + !priv->curve_data || !has_rssical) { +printk (KERN_INFO "%d %p %p %p %d\n" , + synth, priv->iq_autocal, priv->output_limit, + priv->curve_data, has_rssical); +printk (KERN_ERR "%s: not all required entries found in eeprom!\n" ,wiphy_name (dev->wiphy)); err = -EINVAL ;
@@ -708,18 +808,18 @@ int p54_parse_eeprom(struct ieee80211_hw *dev, void *eeprom, int len)wiphy_name (dev->wiphy), dev->wiphy->perm_addr, priv->version, p54_rf_chips[priv->rxhw]); +mutex_unlock (&priv->conf_mutex); +return 0 ; err: -kfree (priv->iq_autocal); -kfree (priv->output_limit); -kfree (priv->curve_data); - priv->iq_autocal =NULL ; - priv->output_limit =NULL ; - priv->curve_data =NULL ; +p54_reset_phydata (priv);printk (KERN_ERR "%s: eeprom parse failed!\n" ,wiphy_name (dev->wiphy)); + +mutex_unlock (&priv->conf_mutex); +return err; }EXPORT_SYMBOL_GPL (p54_parse_eeprom);
@@ -753,8 +853,39 @@ int p54_read_eeprom(struct ieee80211_hw *dev) } ret =p54_parse_eeprom (dev, eeprom, offset); + free:kfree (eeprom);return ret; }EXPORT_SYMBOL_GPL (p54_read_eeprom); + +ssize_t p54_overwrite_eeprom (struct ieee80211_hw *dev, +const char *buf,size_t len) +{ +struct p54_common *priv = dev->priv; +int err; + +if (len <64 || len >0x2020 ) +return -EINVAL ; + +mutex_lock (&priv->sysfs_mutex); +p54_unregister_common (dev); + + err =p54_parse_eeprom (dev, buf, len); +if (err) + goto out; + + err =p54_register_common (dev, priv->pdev); +if (err) + goto out; + +out: + +if (err) +dev_err (priv->pdev,"failed to (re)-register device.\n" ); + +mutex_unlock (&priv->sysfs_mutex); +return (err) ? err : len; +} +EXPORT_SYMBOL_GPL (p54_overwrite_eeprom);
drivers/net/wireless/p54/main.c +16 -4
@@ -582,6 +582,7 @@ struct ieee80211_hw *p54_init_common(size_t priv_data_len) dev->wiphy->flags &= ~WIPHY_FLAG_PS_ON_BY_DEFAULT ;mutex_init (&priv->conf_mutex); +mutex_init (&priv->sysfs_mutex);mutex_init (&priv->eeprom_mutex);init_completion (&priv->eeprom_comp);init_completion (&priv->beacon_comp);
@@ -596,6 +597,9 @@ int p54_register_common(struct ieee80211_hw *dev, struct device *pdev)struct p54_common *priv = dev->priv;int err; +if (priv->registered) +return -EBUSY ; + err =ieee80211_register_hw (dev);if (err) {dev_err (pdev,"Cannot register device (%d).\n" , err);
@@ -607,8 +611,9 @@ int p54_register_common(struct ieee80211_hw *dev, struct device *pdev)if (err)return err;#endif /* CONFIG_P54_LEDS */ - + priv->pdev = pdev;dev_info (pdev,"is registered as '%s'\n" ,wiphy_name (dev->wiphy)); + priv->registered = true;return 0 ; }EXPORT_SYMBOL_GPL (p54_register_common);
@@ -618,6 +623,11 @@ void p54_free_common(struct ieee80211_hw *dev)struct p54_common *priv = dev->priv;unsigned int i; +BUG_ON (priv->registered); + +mutex_destroy (&priv->conf_mutex); +mutex_destroy (&priv->eeprom_mutex); +for (i =0 ; i <IEEE80211_NUM_BANDS ; i++)kfree (priv->band_table[i]);
@@ -637,12 +647,14 @@ void p54_unregister_common(struct ieee80211_hw *dev) {struct p54_common *priv = dev->priv; +if (!priv->registered) +return ; +#ifdef CONFIG_P54_LEDS p54_unregister_leds (priv);#endif /* CONFIG_P54_LEDS */ -ieee80211_unregister_hw (dev); -mutex_destroy (&priv->conf_mutex); -mutex_destroy (&priv->eeprom_mutex); +ieee80211_unregister_hw (priv->hw); + priv->registered = false; }EXPORT_SYMBOL_GPL (p54_unregister_common);
drivers/net/wireless/p54/p54.h +6 -1
@@ -159,6 +159,7 @@ struct p54_led_dev {struct p54_common {struct ieee80211_hw *hw; +struct device *pdev;struct ieee80211_vif *vif;void (*tx)(struct ieee80211_hw *dev,struct sk_buff *skb);int (*open)(struct ieee80211_hw *dev);
@@ -166,6 +167,7 @@ struct p54_common {struct sk_buff_head tx_pending;struct sk_buff_head tx_queue;struct mutex conf_mutex; +bool registered;/* memory management (as seen by the firmware) */ u32 rx_start;
@@ -233,14 +235,17 @@ struct p54_common {void *eeprom;struct completion eeprom_comp;struct mutex eeprom_mutex; +struct mutex sysfs_mutex; };/* interfaces for the drivers */ int p54_rx (struct ieee80211_hw *dev,struct sk_buff *skb);void p54_free_skb (struct ieee80211_hw *dev,struct sk_buff *skb);int p54_parse_firmware (struct ieee80211_hw *dev,const struct firmware *fw); -int p54_parse_eeprom (struct ieee80211_hw *dev,void *eeprom,int len); +int p54_parse_eeprom (struct ieee80211_hw *dev,const void *eeprom,int len);int p54_read_eeprom (struct ieee80211_hw *dev); +ssize_t p54_overwrite_eeprom (struct ieee80211_hw *dev, +const char *eeprom,size_t len);struct ieee80211_hw *p54_init_common (size_t priv_data_len);int p54_register_common (struct ieee80211_hw *dev,struct device *pdev);
drivers/net/wireless/p54/p54pci.c +21 -0
@@ -466,6 +466,18 @@ static int p54p_open(struct ieee80211_hw *dev)return 0 ; } +static ssize_t p54p_sysfs_overwrite_eeprom (struct device *dev, +struct device_attribute *attr, +const char *buf,size_t count) +{ +struct p54p_priv *priv =dev_get_drvdata (dev); + +return p54_overwrite_eeprom (priv->common.hw, buf, count); +} + +static DEVICE_ATTR(eeprom_overwrite, S_IWUSR, + NULL, p54p_sysfs_overwrite_eeprom); +static int __devinit p54p_probe (struct pci_dev *pdev,const struct pci_device_id *id) {
@@ -561,6 +573,13 @@ static int __devinit p54p_probe(struct pci_dev *pdev,if (err) goto err_free_common; + err =device_create_file (&pdev->dev, &dev_attr_eeprom_overwrite); +if (err <0 ) { +dev_err (&pdev->dev,"failed to create sysfs file " +"eeprom_overwrite.\n" ); + goto err_free_common; + } +return 0 ; err_free_common:
@@ -591,6 +610,8 @@ static void __devexit p54p_remove(struct pci_dev *pdev)return ;p54_unregister_common (dev); +device_remove_file (&pdev->dev, &dev_attr_eeprom_overwrite); + priv = dev->priv;release_firmware (priv->firmware); pci_free_consistent(pdev, sizeof(*priv->ring_control),
drivers/net/wireless/p54/p54spi.c +18 -1
@@ -592,6 +592,18 @@ static void p54spi_op_stop(struct ieee80211_hw *dev)mutex_unlock (&priv->mutex); } +static ssize_t p54s_sysfs_overwrite_eeprom (struct device *dev, +struct device_attribute *attr, +const char *buf,size_t count) +{ +struct p54s_priv *priv =dev_get_drvdata (dev); + +return p54_overwrite_eeprom (priv->common.hw, buf, count); +} + +static DEVICE_ATTR(eeprom_overwrite, S_IWUSR, + NULL, p54s_sysfs_overwrite_eeprom); +static int __devinit p54spi_probe (struct spi_device *spi) {struct p54s_priv *priv =NULL ;
@@ -667,7 +679,9 @@ static int __devinit p54spi_probe(struct spi_device *spi)if (ret) goto err_free_common; -return 0 ; + ret =device_create_file (&spi->dev, &dev_attr_eeprom_overwrite); + +return ret; err_free_common:p54_free_common (priv->hw);
@@ -680,6 +694,9 @@ static int __devexit p54spi_remove(struct spi_device *spi)p54_unregister_common (priv->hw); +device_remove_file (&spi->dev, &dev_attr_eeprom_overwrite); +dev_set_drvdata (&spi->dev,NULL ); +free_irq (gpio_to_irq (p54spi_gpio_irq), spi);gpio_free (p54spi_gpio_power);
drivers/net/wireless/p54/p54usb.c +19 -1
@@ -874,6 +874,19 @@ static void p54u_stop(struct ieee80211_hw *dev)return ; } +static ssize_t p54u_sysfs_overwrite_eeprom (struct device *dev, +struct device_attribute *attr, +const char *buf,size_t count) +{ +struct ieee80211_hw *hw = (struct ieee80211_hw *) +usb_get_intfdata (to_usb_interface (dev)); + +return p54_overwrite_eeprom (hw, buf, count); +} + +static DEVICE_ATTR(eeprom_overwrite, S_IWUSR, + NULL, p54u_sysfs_overwrite_eeprom); +static int __devinit p54u_probe (struct usb_interface *intf,const struct usb_device_id *id) {
@@ -959,7 +972,9 @@ static int __devinit p54u_probe(struct usb_interface *intf,if (err) goto err_free_fw; -return 0 ; + err =device_create_file (&intf->dev, &dev_attr_eeprom_overwrite); + +return err; err_free_fw:release_firmware (priv->fw);
@@ -982,6 +997,9 @@ static void __devexit p54u_disconnect(struct usb_interface *intf)p54_unregister_common (dev); priv = dev->priv; +device_remove_file (&intf->dev, &dev_attr_eeprom_overwrite); + +usb_set_intfdata (intf,NULL );usb_put_dev (interface_to_usbdev (intf));release_firmware (priv->fw);p54_free_common (dev);
Quoted 9 lines · Christian Lamparter
This (aggregated) patch adds a new sysfs file "
eeprom_overwrite" which can be used to upload an customized eeprom image to the driver during normal operation.The old wlanX device will quickly vanish. And if the new EEPROM image passes all sanity checks the device will reappear.
Hopefully, this proves to be an adequate solution for everyone with a bad/missing EEPROM data/chip.
Honestly I wonder if this would be better done with ethtool. There's already ethtool --eeprom-dump, would it be so hard to do an ethtool --eeprom-load ?
I can see a number of devices doing this, so in my mind it makes sense to have a generic facility for this sort of thing. But then again it's not so common an operation and its fraught with danger :) Libertas could potentially use this, but libertas has *two* EEPROM images that it might need to update. So if ethtool did grow --eeprom-load we may want to account for more than one eeprom image.
What do people think?
Dan
Quoted 626 lines
---
there are plenty of bugs left!would be nice to hear from p54spi & p54pci folks!
Regards,
Chr
---drivers/net/wireless/p54/eeprom.c +167
-36@@ -121,25 +121,20 @@ static int p54_generate_band(struct ieee80211_hw *dev, enum ieee80211_band band) {struct p54_common *priv = dev->priv; -struct ieee80211_supported_band *tmp, *old; +struct ieee80211_supported_band *old_band, *new_band; +struct ieee80211_channel *tmp, *old_chan, *new_chan;unsigned int i, j; -int ret = -ENOMEM ; +int old_chan_num, ret =0 ;if ((!list->entries) || (!list->band_channel_num[band]))return -EINVAL ; - tmp =kzalloc (sizeof (*tmp),GFP_KERNEL ); -if (!tmp) - goto err_out; - - tmp->channels =kzalloc (sizeof (struct ieee80211_channel ) * - list->band_channel_num[band],GFP_KERNEL ); -if (!tmp->channels) - goto err_out; - - ret =p54_fill_band_bitrates (dev, tmp, band); -if (ret) - goto err_out; + tmp =kzalloc (sizeof (struct ieee80211_channel ) * + list->band_channel_num[band],GFP_KERNEL ); +if (!tmp) { + ret = -ENOMEM ; + goto out; + }for (i =0 , j =0 ; (j < list->band_channel_num[band]) && (i < list->entries); i++) {@@ -161,8 +156,8 @@ static int p54_generate_band(struct ieee80211_hw *dev,continue ; } - tmp->channels[j].band = list->channels[i].band; - tmp->channels[j].center_freq = list->channels[i].freq; + tmp[j].band = list->channels[i].band; + tmp[j].center_freq = list->channels[i].freq; j++; }@@ -172,25 +167,60 @@ static int p54_generate_band(struct ieee80211_hw *dev, "2 GHz" : "5 GHz"); ret = -ENODATA ; - goto err_out; + goto out; } - tmp->n_channels = j; - old = priv->band_table[band]; - priv->band_table[band] = tmp; -if (old) { -kfree (old->channels); -kfree (old); + old_band = priv->band_table[band]; +if (old_band) { + old_chan_num = old_band->n_channels; + old_chan = old_band->channels; + old_band->n_channels =0 ; + old_band->n_bitrates =0 ; + }else { + old_chan_num =0 ; + old_chan =NULL ; } -return 0 ; +if (j < old_chan_num) { +printk (KERN_ERR "%s: Channel list can only be extended.\n" , +wiphy_name (dev->wiphy)); + goto out; + } + + new_band =krealloc (old_band,sizeof (*new_band),GFP_KERNEL ); +if (!new_band) { +printk (KERN_ERR "%s: Unable to modify band table.\n" , +wiphy_name (dev->wiphy)); + + goto out; + } + + new_band->band = band; + new_band->ht_cap.ht_supported = false; -err_out: -if (tmp) { -kfree (tmp->channels); -kfree (tmp); + new_chan =krealloc (old_chan, j *sizeof (struct ieee80211_channel ), +GFP_KERNEL ); + +if (!new_chan) { +printk (KERN_ERR "%s: Unable to modify band channel table.\n" , +wiphy_name (dev->wiphy)); + + goto out; } +memcpy (new_chan, tmp, j *sizeof (struct ieee80211_channel )); + + new_band->channels = new_chan; + new_band->n_channels = j; + + ret =p54_fill_band_bitrates (dev, new_band, band); +if (ret) + goto out; + + priv->band_table[band] = new_band; + +out: +kfree (tmp);return ret; }@@ -533,7 +563,19 @@ static struct p54_cal_database *p54_convert_db(struct pda_custom_wrapper *src,return dst; } -int p54_parse_eeprom (struct ieee80211_hw *dev,void *eeprom,int len) +static void p54_reset_phydata (struct p54_common *priv) +{ +memset (&priv->rssical_db,0 ,sizeof (priv->rssical_db)); + priv->iq_autocal_len =0 ; +kfree (priv->output_limit); +kfree (priv->curve_data); +kfree (priv->iq_autocal); + priv->output_limit =NULL ; + priv->curve_data =NULL ; + priv->iq_autocal =NULL ; +} + +int p54_parse_eeprom (struct ieee80211_hw *dev,const void *eeprom,int len) {struct p54_common *priv = dev->priv;struct eeprom_pda_wrap *wrap;@@ -543,10 +585,14 @@ int p54_parse_eeprom(struct ieee80211_hw *dev, void *eeprom, int len)int err;u8 *end = (u8 *)eeprom + len;u16 synth =0 ; +bool has_rssical = false, has_mac = false, has_country = false; wrap = (struct eeprom_pda_wrap *) eeprom; entry = (void *)wrap->data +le16_to_cpu (wrap->len); +mutex_lock (&priv->conf_mutex); +p54_reset_phydata (priv); +/* verify that at least the entry length/code fits */ while ((u8 *)entry <= end -sizeof (*entry)) { entry_len =le16_to_cpu (entry->len);@@ -558,21 +604,34 @@ int p54_parse_eeprom(struct ieee80211_hw *dev, void *eeprom, int len)switch (le16_to_cpu (entry->code)) {case PDR_MAC_ADDRESS : +if (has_mac) +break ; + + has_mac = true; +if (data_len !=ETH_ALEN )break ; +SET_IEEE80211_PERM_ADDR (dev, entry->data);break ; +case PDR_PRISM_PA_CAL_OUTPUT_POWER_LIMITS :if (priv->output_limit)break ; + err =p54_convert_output_limits (dev, entry->data, data_len);if (err) goto err;break ; +case PDR_PRISM_PA_CAL_CURVE_DATA : {struct pda_pa_curve_data *curve_data = (struct pda_pa_curve_data *)entry->data; + +if (priv->curve_data) +break ; +if (data_len <sizeof (*curve_data)) { err = -EINVAL ; goto err;@@ -597,7 +656,11 @@ int p54_parse_eeprom(struct ieee80211_hw *dev, void *eeprom, int len) goto err; }break ; +case PDR_PRISM_ZIF_TX_IQ_CALIBRATION : +if (priv->iq_autocal) +break ; + priv->iq_autocal =kmalloc (data_len,GFP_KERNEL );if (!priv->iq_autocal) { err = -ENOMEM ;@@ -607,11 +670,22 @@ int p54_parse_eeprom(struct ieee80211_hw *dev, void *eeprom, int len)memcpy (priv->iq_autocal, entry->data, data_len); priv->iq_autocal_len = data_len /sizeof (struct pda_iq_autocal_entry );break ; +case PDR_DEFAULT_COUNTRY : +if (has_country) +break ; + + has_country = true; +p54_parse_default_country (dev, entry->data, data_len);break ; +case PDR_INTERFACE_LIST : tmp = entry->data; + +if (synth) +break ; +while ((u8 *)tmp < entry->data + data_len) {struct exp_if *exp_if = tmp;if (exp_if->if_id ==cpu_to_le16 (IF_ID_ISL39000 ))@@ -619,22 +693,38 @@ int p54_parse_eeprom(struct ieee80211_hw *dev, void *eeprom, int len) tmp +=sizeof (*exp_if); }break ; +case PDR_HARDWARE_PLATFORM_COMPONENT_ID : +if (priv->version) +break ; +if (data_len <2 )break ; priv->version = *(u8 *)(entry->data +1 );break ; +case PDR_RSSI_LINEAR_APPROXIMATION :case PDR_RSSI_LINEAR_APPROXIMATION_DUAL_BAND :case PDR_RSSI_LINEAR_APPROXIMATION_EXTENDED : +if (has_rssical) +break ; + + has_rssical = true; +p54_parse_rssical (dev, entry->data, data_len,le16_to_cpu (entry->code));break ; +case PDR_RSSI_LINEAR_APPROXIMATION_CUSTOM : {__le16 *src = (void *) entry->data;s16 *dst = (void *) &priv->rssical_db;int i; +if (has_rssical) +break ; + + has_rssical = true; +if (data_len !=sizeof (priv->rssical_db)) { err = -EINVAL ; goto err;@@ -644,24 +734,30 @@ int p54_parse_eeprom(struct ieee80211_hw *dev, void *eeprom, int len) *(dst++) = (s16 )le16_to_cpu (*(src++)); }break ; +case PDR_PRISM_PA_CAL_OUTPUT_POWER_LIMITS_CUSTOM : {struct pda_custom_wrapper *pda = (void *) entry->data;if (priv->output_limit || data_len <sizeof (*pda))break ; + priv->output_limit =p54_convert_db (pda, data_len); }break ; +case PDR_PRISM_PA_CAL_CURVE_DATA_CUSTOM : {struct pda_custom_wrapper *pda = (void *) entry->data;if (priv->curve_data || data_len <sizeof (*pda))break ; + priv->curve_data =p54_convert_db (pda, data_len); }break ; +case PDR_END :/* make it overrun */ entry_len = len;break ; +default :break ; }@@ -670,7 +766,11 @@ int p54_parse_eeprom(struct ieee80211_hw *dev, void *eeprom, int len) }if (!synth || !priv->iq_autocal || !priv->output_limit || - !priv->curve_data) { + !priv->curve_data || !has_rssical) { +printk (KERN_INFO "%d %p %p %p %d\n" , + synth, priv->iq_autocal, priv->output_limit, + priv->curve_data, has_rssical); +printk (KERN_ERR "%s: not all required entries found in eeprom!\n" ,wiphy_name (dev->wiphy)); err = -EINVAL ;@@ -708,18 +808,18 @@ int p54_parse_eeprom(struct ieee80211_hw *dev, void *eeprom, int len)wiphy_name (dev->wiphy), dev->wiphy->perm_addr, priv->version, p54_rf_chips[priv->rxhw]); +mutex_unlock (&priv->conf_mutex); +return 0 ; err: -kfree (priv->iq_autocal); -kfree (priv->output_limit); -kfree (priv->curve_data); - priv->iq_autocal =NULL ; - priv->output_limit =NULL ; - priv->curve_data =NULL ; +p54_reset_phydata (priv);printk (KERN_ERR "%s: eeprom parse failed!\n" ,wiphy_name (dev->wiphy)); + +mutex_unlock (&priv->conf_mutex); +return err; }EXPORT_SYMBOL_GPL (p54_parse_eeprom);@@ -753,8 +853,39 @@ int p54_read_eeprom(struct ieee80211_hw *dev) } ret =p54_parse_eeprom (dev, eeprom, offset); + free:kfree (eeprom);return ret; }EXPORT_SYMBOL_GPL (p54_read_eeprom); + +ssize_t p54_overwrite_eeprom (struct ieee80211_hw *dev, +const char *buf,size_t len) +{ +struct p54_common *priv = dev->priv; +int err; + +if (len <64 || len >0x2020 ) +return -EINVAL ; + +mutex_lock (&priv->sysfs_mutex); +p54_unregister_common (dev); + + err =p54_parse_eeprom (dev, buf, len); +if (err) + goto out; + + err =p54_register_common (dev, priv->pdev); +if (err) + goto out; + +out: + +if (err) +dev_err (priv->pdev,"failed to (re)-register device.\n" ); + +mutex_unlock (&priv->sysfs_mutex); +return (err) ? err : len; +} +EXPORT_SYMBOL_GPL (p54_overwrite_eeprom);drivers/net/wireless/p54/main.c +16
-4@@ -582,6 +582,7 @@ struct ieee80211_hw *p54_init_common(size_t priv_data_len) dev->wiphy->flags &= ~WIPHY_FLAG_PS_ON_BY_DEFAULT ;mutex_init (&priv->conf_mutex); +mutex_init (&priv->sysfs_mutex);mutex_init (&priv->eeprom_mutex);init_completion (&priv->eeprom_comp);init_completion (&priv->beacon_comp);@@ -596,6 +597,9 @@ int p54_register_common(struct ieee80211_hw *dev, struct device *pdev)struct p54_common *priv = dev->priv;int err; +if (priv->registered) +return -EBUSY ; + err =ieee80211_register_hw (dev);if (err) {dev_err (pdev,"Cannot register device (%d).\n" , err);@@ -607,8 +611,9 @@ int p54_register_common(struct ieee80211_hw *dev, struct device *pdev)if (err)return err;#endif /* CONFIG_P54_LEDS */ - + priv->pdev = pdev;dev_info (pdev,"is registered as '%s'\n" ,wiphy_name (dev->wiphy)); + priv->registered = true;return 0 ; }EXPORT_SYMBOL_GPL (p54_register_common);@@ -618,6 +623,11 @@ void p54_free_common(struct ieee80211_hw *dev)struct p54_common *priv = dev->priv;unsigned int i; +BUG_ON (priv->registered); + +mutex_destroy (&priv->conf_mutex); +mutex_destroy (&priv->eeprom_mutex); +for (i =0 ; i <IEEE80211_NUM_BANDS ; i++)kfree (priv->band_table[i]);@@ -637,12 +647,14 @@ void p54_unregister_common(struct ieee80211_hw *dev) {struct p54_common *priv = dev->priv; +if (!priv->registered) +return ; +#ifdef CONFIG_P54_LEDS p54_unregister_leds (priv);#endif /* CONFIG_P54_LEDS */ -ieee80211_unregister_hw (dev); -mutex_destroy (&priv->conf_mutex); -mutex_destroy (&priv->eeprom_mutex); +ieee80211_unregister_hw (priv->hw); + priv->registered = false; }EXPORT_SYMBOL_GPL (p54_unregister_common);drivers/net/wireless/p54/p54.h +6
-1@@ -159,6 +159,7 @@ struct p54_led_dev {struct p54_common {struct ieee80211_hw *hw; +struct device *pdev;struct ieee80211_vif *vif;void (*tx)(struct ieee80211_hw *dev,struct sk_buff *skb);int (*open)(struct ieee80211_hw *dev);@@ -166,6 +167,7 @@ struct p54_common {struct sk_buff_head tx_pending;struct sk_buff_head tx_queue;struct mutex conf_mutex; +bool registered;/* memory management (as seen by the firmware) */ u32 rx_start;@@ -233,14 +235,17 @@ struct p54_common {void *eeprom;struct completion eeprom_comp;struct mutex eeprom_mutex; +struct mutex sysfs_mutex; };/* interfaces for the drivers */ int p54_rx (struct ieee80211_hw *dev,struct sk_buff *skb);void p54_free_skb (struct ieee80211_hw *dev,struct sk_buff *skb);int p54_parse_firmware (struct ieee80211_hw *dev,const struct firmware *fw); -int p54_parse_eeprom (struct ieee80211_hw *dev,void *eeprom,int len); +int p54_parse_eeprom (struct ieee80211_hw *dev,const void *eeprom,int len);int p54_read_eeprom (struct ieee80211_hw *dev); +ssize_t p54_overwrite_eeprom (struct ieee80211_hw *dev, +const char *eeprom,size_t len);struct ieee80211_hw *p54_init_common (size_t priv_data_len);int p54_register_common (struct ieee80211_hw *dev,struct device *pdev);drivers/net/wireless/p54/p54pci.c +21
-0@@ -466,6 +466,18 @@ static int p54p_open(struct ieee80211_hw *dev)return 0 ; } +static ssize_t p54p_sysfs_overwrite_eeprom (struct device *dev, +struct device_attribute *attr, +const char *buf,size_t count) +{ +struct p54p_priv *priv =dev_get_drvdata (dev); + +return p54_overwrite_eeprom (priv->common.hw, buf, count); +} + +static DEVICE_ATTR(eeprom_overwrite, S_IWUSR, + NULL, p54p_sysfs_overwrite_eeprom); +static int __devinit p54p_probe (struct pci_dev *pdev,const struct pci_device_id *id) {@@ -561,6 +573,13 @@ static int __devinit p54p_probe(struct pci_dev *pdev,if (err) goto err_free_common; + err =device_create_file (&pdev->dev, &dev_attr_eeprom_overwrite); +if (err <0 ) { +dev_err (&pdev->dev,"failed to create sysfs file " +"eeprom_overwrite.\n" ); + goto err_free_common; + } +return 0 ; err_free_common:@@ -591,6 +610,8 @@ static void __devexit p54p_remove(struct pci_dev *pdev)return ;p54_unregister_common (dev); +device_remove_file (&pdev->dev, &dev_attr_eeprom_overwrite); + priv = dev->priv;release_firmware (priv->firmware); pci_free_consistent(pdev, sizeof(*priv->ring_control),drivers/net/wireless/p54/p54spi.c +18
-1@@ -592,6 +592,18 @@ static void p54spi_op_stop(struct ieee80211_hw *dev)mutex_unlock (&priv->mutex); } +static ssize_t p54s_sysfs_overwrite_eeprom (struct device *dev, +struct device_attribute *attr, +const char *buf,size_t count) +{ +struct p54s_priv *priv =dev_get_drvdata (dev); + +return p54_overwrite_eeprom (priv->common.hw, buf, count); +} + +static DEVICE_ATTR(eeprom_overwrite, S_IWUSR, + NULL, p54s_sysfs_overwrite_eeprom); +static int __devinit p54spi_probe (struct spi_device *spi) {struct p54s_priv *priv =NULL ;@@ -667,7 +679,9 @@ static int __devinit p54spi_probe(struct spi_device *spi)if (ret) goto err_free_common; -return 0 ; + ret =device_create_file (&spi->dev, &dev_attr_eeprom_overwrite); + +return ret; err_free_common:p54_free_common (priv->hw);@@ -680,6 +694,9 @@ static int __devexit p54spi_remove(struct spi_device *spi)p54_unregister_common (priv->hw); +device_remove_file (&spi->dev, &dev_attr_eeprom_overwrite); +dev_set_drvdata (&spi->dev,NULL ); +free_irq (gpio_to_irq (p54spi_gpio_irq), spi);gpio_free (p54spi_gpio_power);drivers/net/wireless/p54/p54usb.c +19
-2@@ -874,6 +874,19 @@ static void p54u_stop(struct ieee80211_hw *dev)return ; } +static ssize_t p54u_sysfs_overwrite_eeprom (struct device *dev, +struct device_attribute *attr, +const char *buf,size_t count) +{ +struct ieee80211_hw *hw = (struct ieee80211_hw *) +usb_get_intfdata (to_usb_interface (dev)); + +return p54_overwrite_eeprom (hw, buf, count); +} + +static DEVICE_ATTR(eeprom_overwrite, S_IWUSR, + NULL, p54u_sysfs_overwrite_eeprom); +static int __devinit p54u_probe (struct usb_interface *intf,const struct usb_device_id *id) {@@ -959,7 +972,9 @@ static int __devinit p54u_probe(struct usb_interface *intf,if (err) goto err_free_fw; -return 0 ; + err =device_create_file (&intf->dev, &dev_attr_eeprom_overwrite); + +return err; err_free_fw:release_firmware (priv->fw);@@ -982,6 +997,9 @@ static void __devexit p54u_disconnect(struct usb_interface *intf)p54_unregister_common (dev); priv = dev->priv; +device_remove_file (&intf->dev, &dev_attr_eeprom_overwrite); + +usb_set_intfdata (intf,NULL );usb_put_dev (interface_to_usbdev (intf));release_firmware (priv->fw);p54_free_common (dev); --To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
A message that is not in the archive (sent off-list or not yet received): 1258746786.26965.83.camel-bi+AKbBUZKY6gyzm1THtWbp2dZbC/[email protected]
Quoted 15 lines · Dan Williams
Quoted 9 lines · Christian Lamparter
This (aggregated) patch adds a new sysfs file "
eeprom_overwrite" which can be used to upload an customized eeprom image to the driver during normal operation.The old wlanX device will quickly vanish. And if the new EEPROM image passes all sanity checks the device will reappear.
Hopefully, this proves to be an adequate solution for everyone with a bad/missing EEPROM data/chip.
Honestly I wonder if this would be better done with ethtool. There's already ethtool --eeprom-dump, would it be so hard to do an ethtool --eeprom-load ?
Quoted 8 lines
I can see a number of devices doing this, so in my mind it makes sense to have a generic facility for this sort of thing. But then again it's not so common an operation and its fraught with danger :) Libertas could potentially use this, but libertas has *two* EEPROM images that it might need to update. So if ethtool did grow --eeprom-load we may want to account for more than one eeprom image.
What do people think?
Can't request_firmware() be generalized for this sort of stuff too?
Luis
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 4 lines · Dan Williams
Quoted 3 lines · Christian Lamparter
This (aggregated) patch adds a new sysfs file "
eeprom_overwrite" which can be used to upload an customized eeprom image to the driver during normal operation.
[...]
Quoted 7 lines
Honestly I wonder if this would be better done with ethtool. There's already ethtool --eeprom-dump, would it be so hard to do an ethtool --eeprom-load ?
I can see a number of devices doing this, so in my mind it makes sense to have a generic facility for this sort of thing. But then again it's not so common an operation and its fraught with danger :)
I think that devices without eeprom at all (eg. stlc4550, most wl1251 and all wl1271 chips) request_firmware() and a udev script is the best way to go, as they will need the eeprom data from user space during every boot. This was discussed few months back, but unfortunately I have yet to seen an implementation of this :) Hopefully I find some time to try this soon.
But for devices with eeprom, having support in ethtool sounds good to me.
Quoted 3 lines
Libertas could potentially use this, but libertas has *two* EEPROM images that it might need to update. So if ethtool did grow --eeprom-load we may want to account for more than one eeprom image.
Makes sense to mee.
Signature · 1 line
Kalle Valo
Quoted 9 lines · Christian Lamparter
This (aggregated) patch adds a new sysfs file "
eeprom_overwrite" which can be used to upload an customized eeprom image to the driver during normal operation.The old wlanX device will quickly vanish. And if the new EEPROM image passes all sanity checks the device will reappear.
Hopefully, this proves to be an adequate solution for everyone with a bad/missing EEPROM data/chip.
Wasn't the concensus that request_firmware() will be used for this kind of device specific data? stlc45xx had a similar sysfs interface and people didn't like it. And I tend to agree with them, adding odd sysfs files is not the best way to handle this.
Signature · 1 line
Kalle Valo
Quoted 9 lines · Kalle Valo
Quoted 7 lines · Christian Lamparter
This (aggregated) patch adds a new sysfs file "
eeprom_overwrite" which can be used to upload an customized eeprom image to the driver during normal operation.The old wlanX device will quickly vanish. And if the new EEPROM image passes all sanity checks the device will reappear.
Quoted 7 lines
Quoted 2 lines
Hopefully, this proves to be an adequate solution for everyone with a bad/missing EEPROM data/chip.
Wasn't the concensus that
request_firmware()will be used for this kind of device specific data? stlc45xx had a similar sysfs interface and people didn't like it. And I tend to agree with them, adding odd sysfs files is not the best way to handle this.
It could be yes, but what would the trigger to upload the new firmware be? A /standard/ sysfs file that you
echo "new-firmware-v345" > eeprom_write
into that would then request_firmware("new-firmware-v345")? I don't really care where read/write functionality is, I just want this stuff to be in one place and not have one mechanism for reading it and a few different ones for writing it.
Dan
Quoted 11 lines · Dan Williams
Quoted 4 lines
Wasn't the concensus that
request_firmware()will be used for this kind of device specific data? stlc45xx had a similar sysfs interface and people didn't like it. And I tend to agree with them, adding odd sysfs files is not the best way to handle this.It could be yes, but what would the trigger to upload the new firmware be? A /standard/ sysfs file that you
echo "new-firmware-v345" >
eeprom_writeinto that would then
request_firmware("new-firmware-v345")?
To be sure that we are talking about the same stuff, let's clarify this a bit first. There are two different use cases where eeprom from user space is needed:
Category 1. Devices which don't have eeprom at all and require the
user space provides the eeprom data during every device boot. These devices won't even function correctly if they don't get the correct eeprom data from user space. As an example, grep nvs from wl12xx.
Category 2. Devices which have eeprom but can be updated by user.
So we have two separate problems here.
For category 1 devices request_firmware() was proposed earlier and for category 2 the ethtool support you mentioned sounds like a viable option.
Signature · 1 line
Kalle Valo
Quoted 18 lines · Kalle Valo
Quoted 11 lines · Dan Williams
Quoted 4 lines
Wasn't the concensus that
request_firmware()will be used for this kind of device specific data? stlc45xx had a similar sysfs interface and people didn't like it. And I tend to agree with them, adding odd sysfs files is not the best way to handle this.It could be yes, but what would the trigger to upload the new firmware be? A /standard/ sysfs file that you
echo "new-firmware-v345" >
eeprom_writeinto that would then
request_firmware("new-firmware-v345")?To be sure that we are talking about the same stuff, let's clarify this a bit first. There are two different use cases where eeprom from user space is needed:
Quoted 5 lines
Category 1. Devices which don't have eeprom at all and require the
user space provides the eeprom data during every device boot. These devices won't even function correctly if they don't get the correct eeprom data from user space. As an example, grep nvs from wl12xx.
Obviously; pretty much every driver that needs firmware does this already, yeah. And uses request_firmware().
Quoted 1 line
Category 2. Devices which have eeprom but can be updated by user.
I was under the impression that chr's original patch was doing #2 here. Run-time update of firmware. I guess if the device doesn't actually write the new firmware to eeprom then yeah, use #1. Thought his case was #2 or something.
Dan
Quoted 9 lines · On Friday 20 November 2009 21:24:27 Kalle Valo wrote:
Quoted 7 lines · Christian Lamparter
This (aggregated) patch adds a new sysfs file "
eeprom_overwrite" which can be used to upload an customized eeprom image to the driver during normal operation.The old wlanX device will quickly vanish. And if the new EEPROM image passes all sanity checks the device will reappear.
Quoted 7 lines
Quoted 2 lines
Hopefully, this proves to be an adequate solution for everyone with a bad/missing EEPROM data/chip.
Wasn't the concensus that
request_firmware()will be used for this kind of device specific data? stlc45xx had a similar sysfs interface and people didn't like it. And I tend to agree with them, adding odd sysfs files is not the best way to handle this.
no, I wanted something that could fix every possible problem.
I know of several different devices which could use more or less the same fixes, but we want to retain the mac-addresses, baseband/mac processor info, PHYs and hw-layout related features (or in other words: 95% of the eeprom _other_ content).
Here's *real* list of the problems:
p54pci devices:
1. CardBus Netgear WG511 (duette phy / ISL3880 mac)
- (no country code)
- (disabled antenna diversity)
- *swapped rssi<->dbm parameters*
=> affects internal calibration and link stability,
renders dBm reading totally useless,
2. miniPCI ZComax XG-601 (frisbee phy / ISL3880 mac)
- (no country code)
- (disabled antenna diversity)
3. miniPCI ZComax XG-603 (frisbee phy / ISL3886 mac)
- (no country code)
- (disabled antenna diversity)
- *fixed* output power limits (the card _only_ transmits @ 14 dBm)
4. miniPCI Allnet 271 (frisbee phy / ISL3880 mac)
- (no country code)
- (disabled antenna diversity)
5. James' minipci Gigafast WF728-AEX (frisbee phy / isl3880 mac)
- (no country code)
- (disabled antenna diversity)
- incomplete phy calibration data
=> card only works on channel 1, 7, 12, 14
p54usb devices:
1. Dell 1450 USB (crossbow phy / ISL3892 mac)
- *wrong* country code
(disables all non-US channels, even though it's OK to use them in the EU)
- disabled antenna diversity
Or in other words, I haven't come a cross a single p54 device with a proper EEPROM since I picked up my first card 3/4 years ago...
anyway, I had to think about it again:eeprom_overwrite is no longer meant to fully replace the onboard eeprom, or in p54spi's case the supplied (minimal) blob data. It should (not yet, but hopefully in the next RFC, if we all agree on something) merely allow users to fix the faulty pieces without altering the unaffected bits (like volatile patch deltas for the static const eeprom).
In fact I gave it a new name already: volatile_eeprom_patch :-D .
I'm unsure about ethtool --eeprom-load. Because unlike --change-eeprom, we won't be able to mess around with low-level physical bits flipping in the EEPROM itself, so people might get confused why they _setting_ doesn't stick over modules reloads/reboots etc...
Regards,
Chr
---
damn bugs!