Skip to contentSkip to conversation

sfc: QT202x: Reset before reading PHY id

PATCH Applied Ben Hutchings 2 participants 2 messages Nov 28, 2009 – Nov 29, 2009

Subsystems (2)
Networking Network drivers
lore
Share & tools
lore

Ben Hutchings

author
#0 lore raw

PATCH 2/12 sfc: QT202x: Reset before reading PHY id

From: Steve Hodgson <[email protected]>

Reading standard registers on the QT2025C before its firmware has booted may cause the boot process to fail. Therefore, follow the recommended reset sequence before reading its id registers. Either order works for the QT2022C2, so don't differentiate.

Signed-off-by Ben Hutchings <[email protected]>
---
 drivers/net/sfc/qt202x_phy.c |   22 ++++++++--------------
 1 files changed, 8 insertions(+), 14 deletions(-)
drivers/net/sfc/qt202x_phy.c +8 -14
index 1b174c3..3d7370e 100644
@@ -138,33 +138,27 @@ static int qt202x_reset_phy(struct efx_nic *efx)
 static int qt202x_phy_init(struct efx_nic *efx)
 {
 	struct qt202x_phy_data *phy_data;
-	u32 devid = efx_mdio_read_id(efx, MDIO_MMD_PHYXS);
+	u32 devid;
 	int rc;
 
+	rc = qt202x_reset_phy(efx);
+	if (rc) {
+		EFX_ERR(efx, "PHY init failed\n");
+		return rc;
+	}
+
 	phy_data = kzalloc(sizeof(struct qt202x_phy_data), GFP_KERNEL);
 	if (!phy_data)
 		return -ENOMEM;
 	efx->phy_data = phy_data;
 
+	devid = efx_mdio_read_id(efx, MDIO_MMD_PHYXS);
 	EFX_INFO(efx, "PHY ID reg %x (OUI %06x model %02x revision %x)\n",
 		 devid, efx_mdio_id_oui(devid), efx_mdio_id_model(devid),
 		 efx_mdio_id_rev(devid));
 
 	phy_data->phy_mode = efx->phy_mode;
-
-	rc = qt202x_reset_phy(efx);
-
-	EFX_INFO(efx, "PHY init %s.\n",
-		 rc ? "failed" : "successful");
-	if (rc < 0)
-		goto fail;
-
 	return 0;
-
- fail:
-	kfree(efx->phy_data);
-	efx->phy_data = NULL;
-	return rc;
 }
 
 static int qt202x_link_ok(struct efx_nic *efx)
Signature · 9 lines
1.6.5.3




-- 
Ben Hutchings, Senior Software Engineer, Solarflare Communications
Not speaking for my employer; that's the marketing department's job.
They asked us to note that Solarflare product names are trademarked.
maintainer Applied
#1 lore raw

From: Ben Hutchings <[email protected]>
Date: Sat, 28 Nov 2009 15:34:29 +0000

Quoted 8 lines

From: Steve Hodgson <[email protected]>

Reading standard registers on the QT2025C before its firmware has booted may cause the boot process to fail. Therefore, follow the recommended reset sequence before reading its id registers. Either order works for the QT2022C2, so don't differentiate.

Signed-off-by Ben Hutchings <[email protected]>

Applied.