Skip to contentSkip to conversation

serial-core: resume serial hardware with no_console_suspend (resend)

PATCH In review Stanislav Brabec 2 participants 2 messages Dec 2, 2009 – Dec 3, 2009

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 serial-core: resume serial hardware with no_console_suspend (resend)

Perform a tricky suspend/resume even with no_console_suspend.

With no_console_suspend, kernel skips serial port suspend/resume and the serial hardware may remain in undefined state after resume. It actually happens on devices that don't have BIOS that handle serial initialization. It makes impossible to use serial console after resume.

Devices affected by this problem include:
Sharp Zaurus devices
Several PXA based ARM embedded boards

The patch does:
- Save the hardware state
- Perform buffer flush in time of its suspend call
- Tell the driver that port is suspended
- But still accept new data
- And keep console hardware in state that allows to send them

It allows to capture late console messages without breaking console after resume.

This is just a resend of a patch discussed in these threads, as the patch was not yet applied.

"Possible suspend/resume regression in .32-rc?" (Nov 1-5, 2009, ARM list, later LKML)

"serial-core: resume serial hardware with no_console_suspend" (Sep 15-Oct 18, 2009, LKML & ARM lists)

drivers/serial/serial_core.c +33 -55
index dcc7244..f1e1ab2 100644
@@ -2008,12 +2008,6 @@ int uart_suspend_port(struct uart_driver *drv, struct uart_port *uport)
 
 	mutex_lock(&port->mutex);
 
-	if (!console_suspend_enabled && uart_console(uport)) {
-		/* we're going to avoid suspending serial console */
-		mutex_unlock(&port->mutex);
-		return 0;
-	}
-
 	tty_dev = device_find_child(uport->dev, &match, serial_match_port);
 	if (device_may_wakeup(tty_dev)) {
 		enable_irq_wake(uport->irq);
@@ -2021,20 +2015,23 @@ int uart_suspend_port(struct uart_driver *drv, struct uart_port *uport)
 		mutex_unlock(&port->mutex);
 		return 0;
 	}
-	uport->suspended = 1;
+	if (console_suspend_enabled || !uart_console(uport))
+		uport->suspended = 1;
 
 	if (port->flags & ASYNC_INITIALIZED) {
 		const struct uart_ops *ops = uport->ops;
 		int tries;
 
-		set_bit(ASYNCB_SUSPENDED, &port->flags);
-		clear_bit(ASYNCB_INITIALIZED, &port->flags);
+		if (console_suspend_enabled || !uart_console(uport)) {
+			set_bit(ASYNCB_SUSPENDED, &port->flags);
+			clear_bit(ASYNCB_INITIALIZED, &port->flags);
 
-		spin_lock_irq(&uport->lock);
-		ops->stop_tx(uport);
-		ops->set_mctrl(uport, 0);
-		ops->stop_rx(uport);
-		spin_unlock_irq(&uport->lock);
+			spin_lock_irq(&uport->lock);
+			ops->stop_tx(uport);
+			ops->set_mctrl(uport, 0);
+			ops->stop_rx(uport);
+			spin_unlock_irq(&uport->lock);
+		}
 
 		/*
 		 * Wait for the transmitter to empty.
@@ -2049,16 +2046,18 @@ int uart_suspend_port(struct uart_driver *drv, struct uart_port *uport)
 			       drv->dev_name,
 			       drv->tty_driver->name_base + uport->line);
 
-		ops->shutdown(uport);
+		if (console_suspend_enabled || !uart_console(uport))
+			ops->shutdown(uport);
 	}
 
 	/*
 	 * Disable the console device before suspending.
 	 */
-	if (uart_console(uport))
+	if (console_suspend_enabled && uart_console(uport))
 		console_stop(uport->cons);
 
-	uart_change_pm(state, 3);
+	if (console_suspend_enabled || !uart_console(uport))
+		uart_change_pm(state, 3);
 
 	mutex_unlock(&port->mutex);
 
@@ -2075,29 +2074,6 @@ int uart_resume_port(struct uart_driver *drv, struct uart_port *uport)
 
 	mutex_lock(&port->mutex);
 
-	if (!console_suspend_enabled && uart_console(uport)) {
-		/* no need to resume serial console, it wasn't suspended */
-		/*
-		 * First try to use the console cflag setting.
-		 */
-		memset(&termios, 0, sizeof(struct ktermios));
-		termios.c_cflag = uport->cons->cflag;
-		/*
-		 * If that's unset, use the tty termios setting.
-		 */
-		if (termios.c_cflag == 0)
-			termios = *state->port.tty->termios;
-		else {
-			termios.c_ispeed = termios.c_ospeed =
-				tty_termios_input_baud_rate(&termios);
-			termios.c_ispeed = termios.c_ospeed =
-				tty_termios_baud_rate(&termios);
-		}
-		uport->ops->set_termios(uport, &termios, NULL);
-		mutex_unlock(&port->mutex);
-		return 0;
-	}
-
 	tty_dev = device_find_child(uport->dev, &match, serial_match_port);
 	if (!uport->suspended && device_may_wakeup(tty_dev)) {
 		disable_irq_wake(uport->irq);
@@ -2123,21 +2099,23 @@ int uart_resume_port(struct uart_driver *drv, struct uart_port *uport)
 		spin_lock_irq(&uport->lock);
 		ops->set_mctrl(uport, 0);
 		spin_unlock_irq(&uport->lock);
-		ret = ops->startup(uport);
-		if (ret == 0) {
-			uart_change_speed(state, NULL);
-			spin_lock_irq(&uport->lock);
-			ops->set_mctrl(uport, uport->mctrl);
-			ops->start_tx(uport);
-			spin_unlock_irq(&uport->lock);
-			set_bit(ASYNCB_INITIALIZED, &port->flags);
-		} else {
-			/*
-			 * Failed to resume - maybe hardware went away?
-			 * Clear the "initialized" flag so we won't try
-			 * to call the low level drivers shutdown method.
-			 */
-			uart_shutdown(state);
+		if (console_suspend_enabled || !uart_console(uport)) {
+			ret = ops->startup(uport);
+			if (ret == 0) {
+				uart_change_speed(state, NULL);
+				spin_lock_irq(&uport->lock);
+				ops->set_mctrl(uport, uport->mctrl);
+				ops->start_tx(uport);
+				spin_unlock_irq(&uport->lock);
+				set_bit(ASYNCB_INITIALIZED, &port->flags);
+			} else {
+				/*
+				 * Failed to resume - maybe hardware went away?
+				 * Clear the "initialized" flag so we won't try
+				 * to call the low level drivers shutdown method.
+				 */
+				uart_shutdown(state);
+			}
 		}
 
 		clear_bit(ASYNCB_SUSPENDED, &port->flags);
Signature · 9 lines
Best Regards / S pozdravem,

Stanislav Brabec
software developer
---------------------------------------------------------------------
SUSE LINUX, s. r. o.                          e-mail: [email protected]
Lihovarská 1060/12           tel: +420 284 028 966, +49 911 740538747
190 00 Praha 9                                  fax: +420 284 028 951
Czech Republic                                    http://www.suse.cz/
Tested-by on v1 1/1
#1 lore raw
Quoted 10 lines · Stanislav Brabec

Perform a tricky suspend/resume even with no_console_suspend.

With no_console_suspend, kernel skips serial port suspend/resume and the serial hardware may remain in undefined state after resume. It actually happens on devices that don't have BIOS that handle serial initialization. It makes impossible to use serial console after resume.

Devices affected by this problem include:
Sharp Zaurus devices
Several PXA based ARM embedded boards

True, I had occasions where the serial console did not get back to life after suspend on a PXA300 based device. It didn't always happen though.

Quoted 13 lines

The patch does:
- Save the hardware state
- Perform buffer flush in time of its suspend call
- Tell the driver that port is suspended
- But still accept new data
- And keep console hardware in state that allows to send them

It allows to capture late console messages without breaking console after resume.

This is just a resend of a patch discussed in these threads, as the patch was not yet applied.

Quoted 8 lines

"Possible suspend/resume regression in .32-rc?" (Nov 1-5, 2009, ARM list, later LKML)

"serial-core: resume serial hardware with no_console_suspend" (Sep 15-Oct 18, 2009, LKML & ARM lists)

And I didn't see that problem anymore since your patch is applied, great!

Thanks,
Daniel

Quoted 156 lines
drivers/serial/serial_core.c +33 -55
index dcc7244..f1e1ab2 100644
@@ -2008,12 +2008,6 @@ int uart_suspend_port(struct uart_driver *drv, struct uart_port *uport)
 
 	mutex_lock(&port->mutex);
 
-	if (!console_suspend_enabled && uart_console(uport)) {
-		/* we're going to avoid suspending serial console */
-		mutex_unlock(&port->mutex);
-		return 0;
-	}
-
 	tty_dev = device_find_child(uport->dev, &match, serial_match_port);
 	if (device_may_wakeup(tty_dev)) {
 		enable_irq_wake(uport->irq);
@@ -2021,20 +2015,23 @@ int uart_suspend_port(struct uart_driver *drv, struct uart_port *uport)
 		mutex_unlock(&port->mutex);
 		return 0;
 	}
-	uport->suspended = 1;
+	if (console_suspend_enabled || !uart_console(uport))
+		uport->suspended = 1;
 
 	if (port->flags & ASYNC_INITIALIZED) {
 		const struct uart_ops *ops = uport->ops;
 		int tries;
 
-		set_bit(ASYNCB_SUSPENDED, &port->flags);
-		clear_bit(ASYNCB_INITIALIZED, &port->flags);
+		if (console_suspend_enabled || !uart_console(uport)) {
+			set_bit(ASYNCB_SUSPENDED, &port->flags);
+			clear_bit(ASYNCB_INITIALIZED, &port->flags);
 
-		spin_lock_irq(&uport->lock);
-		ops->stop_tx(uport);
-		ops->set_mctrl(uport, 0);
-		ops->stop_rx(uport);
-		spin_unlock_irq(&uport->lock);
+			spin_lock_irq(&uport->lock);
+			ops->stop_tx(uport);
+			ops->set_mctrl(uport, 0);
+			ops->stop_rx(uport);
+			spin_unlock_irq(&uport->lock);
+		}
 
 		/*
 		 * Wait for the transmitter to empty.
@@ -2049,16 +2046,18 @@ int uart_suspend_port(struct uart_driver *drv, struct uart_port *uport)
 			       drv->dev_name,
 			       drv->tty_driver->name_base + uport->line);
 
-		ops->shutdown(uport);
+		if (console_suspend_enabled || !uart_console(uport))
+			ops->shutdown(uport);
 	}
 
 	/*
 	 * Disable the console device before suspending.
 	 */
-	if (uart_console(uport))
+	if (console_suspend_enabled && uart_console(uport))
 		console_stop(uport->cons);
 
-	uart_change_pm(state, 3);
+	if (console_suspend_enabled || !uart_console(uport))
+		uart_change_pm(state, 3);
 
 	mutex_unlock(&port->mutex);
 
@@ -2075,29 +2074,6 @@ int uart_resume_port(struct uart_driver *drv, struct uart_port *uport)
 
 	mutex_lock(&port->mutex);
 
-	if (!console_suspend_enabled && uart_console(uport)) {
-		/* no need to resume serial console, it wasn't suspended */
-		/*
-		 * First try to use the console cflag setting.
-		 */
-		memset(&termios, 0, sizeof(struct ktermios));
-		termios.c_cflag = uport->cons->cflag;
-		/*
-		 * If that's unset, use the tty termios setting.
-		 */
-		if (termios.c_cflag == 0)
-			termios = *state->port.tty->termios;
-		else {
-			termios.c_ispeed = termios.c_ospeed =
-				tty_termios_input_baud_rate(&termios);
-			termios.c_ispeed = termios.c_ospeed =
-				tty_termios_baud_rate(&termios);
-		}
-		uport->ops->set_termios(uport, &termios, NULL);
-		mutex_unlock(&port->mutex);
-		return 0;
-	}
-
 	tty_dev = device_find_child(uport->dev, &match, serial_match_port);
 	if (!uport->suspended && device_may_wakeup(tty_dev)) {
 		disable_irq_wake(uport->irq);
@@ -2123,21 +2099,23 @@ int uart_resume_port(struct uart_driver *drv, struct uart_port *uport)
 		spin_lock_irq(&uport->lock);
 		ops->set_mctrl(uport, 0);
 		spin_unlock_irq(&uport->lock);
-		ret = ops->startup(uport);
-		if (ret == 0) {
-			uart_change_speed(state, NULL);
-			spin_lock_irq(&uport->lock);
-			ops->set_mctrl(uport, uport->mctrl);
-			ops->start_tx(uport);
-			spin_unlock_irq(&uport->lock);
-			set_bit(ASYNCB_INITIALIZED, &port->flags);
-		} else {
-			/*
-			 * Failed to resume - maybe hardware went away?
-			 * Clear the "initialized" flag so we won't try
-			 * to call the low level drivers shutdown method.
-			 */
-			uart_shutdown(state);
+		if (console_suspend_enabled || !uart_console(uport)) {
+			ret = ops->startup(uport);
+			if (ret == 0) {
+				uart_change_speed(state, NULL);
+				spin_lock_irq(&uport->lock);
+				ops->set_mctrl(uport, uport->mctrl);
+				ops->start_tx(uport);
+				spin_unlock_irq(&uport->lock);
+				set_bit(ASYNCB_INITIALIZED, &port->flags);
+			} else {
+				/*
+				 * Failed to resume - maybe hardware went away?
+				 * Clear the "initialized" flag so we won't try
+				 * to call the low level drivers shutdown method.
+				 */
+				uart_shutdown(state);
+			}
 		}
 
 		clear_bit(ASYNCB_SUSPENDED, &port->flags);
Signature · 10 lines
-- 
Best Regards / S pozdravem,

Stanislav Brabec
software developer
---------------------------------------------------------------------
SUSE LINUX, s. r. o.                          e-mail: [email protected]
Lihovarská 1060/12           tel: +420 284 028 966, +49 911 740538747
190 00 Praha 9                                  fax: +420 284 028 951
Czech Republic                                    http://www.suse.cz/