mx27: mxt_td60: Add USB Support
Subsystems (3)
PATCH 1/1 mx27: mxt_td60: Add USB Support
This patch add USB support on i-MXT TD60 to Host1 and Host2 ports.
--- arch/arm/mach-mx2/Kconfig | 1 + arch/arm/mach-mx2/mxt_td60.c | 106 +++++++++++++++++++++++++++ arch/arm/plat-mxc/include/mach/iomux-mx27.h | 14 ++++ 3 files changed, 121 insertions(+), 0 deletions(-)
arch/arm/mach-mx2/Kconfig +1 -0
@@ -107,6 +107,7 @@ config MACH_PCA100 config MACH_MXT_TD60 bool "Maxtrack i-MXT TD60" depends on MACH_MX27 + select MXC_ULPI help Include support for i-MXT (aka td60) platform. This includes specific configurations for the module and its peripherals.
arch/arm/mach-mx2/mxt_td60.c +106 -0
136 lines not on this page · raw message
arch/arm/plat-mxc/include/mach/iomux-mx27.h +14 -0
@@ -33,7 +33,14 @@#define PA3_PF_USBH2_NXT (GPIO_PORTA | GPIO_PF | 3)#define PA4_PF_USBH2_STP (GPIO_PORTA | GPIO_PF | 4)#define PB22_PF_USBH1_SUSP (GPIO_PORTB | GPIO_PF | 22) +#define PB23_PF_USB_PWR (GPIO_PORTB | GPIO_PF | 23)#define PB25_PF_USBH1_RCV (GPIO_PORTB | GPIO_PF | 25) +#define PB26_PF_USBH1_FS (GPIO_PORTB | GPIO_PF | 26) +#define PB27_PF_USBH1_OE_B (GPIO_PORTB | GPIO_PF | 27) +#define PB28_PF_USBH1_TXDM (GPIO_PORTB | GPIO_PF | 28) +#define PB29_PF_USBH1_TXDP (GPIO_PORTB | GPIO_PF | 29) +#define PB30_PF_USBH1_RXDM (GPIO_PORTB | GPIO_PF | 30) +#define PB31_PF_USBH1_RXDP (GPIO_PORTB | GPIO_PF | 31)#define PC5_PF_I2C2_SDA (GPIO_PORTC | GPIO_PF | GPIO_IN | 5)#define PC6_PF_I2C2_SCL (GPIO_PORTC | GPIO_PF | GPIO_IN | 6)#define PC7_PF_USBOTG_DATA5 (GPIO_PORTC | GPIO_PF | GPIO_OUT | 7)
@@ -123,6 +130,13 @@#define PD14_AF_ETMTRACE_PKT7 (GPIO_PORTD | GPIO_AF | 14)#define PD15_AF_ETMTRACE_PKT6 (GPIO_PORTD | GPIO_AF | 15)#define PD16_AF_ETMTRACE_PKT5 (GPIO_PORTD | GPIO_AF | 16) +#define PD19_AF_USBH2_DATA4 (GPIO_PORTD | GPIO_AF | 19) +#define PD20_AF_USBH2_DATA3 (GPIO_PORTD | GPIO_AF | 20) +#define PD21_AF_USBH2_DATA6 (GPIO_PORTD | GPIO_AF | 21) +#define PD22_AF_USBH2_DATA0 (GPIO_PORTD | GPIO_AF | 22) +#define PD23_AF_USBH2_DATA2 (GPIO_PORTD | GPIO_AF | 23) +#define PD24_AF_USBH2_DATA1 (GPIO_PORTD | GPIO_AF | 24) +#define PD26_AF_USBH2_DATA5 (GPIO_PORTD | GPIO_AF | 26)#define PF1_AF_ETMTRACE_PKT0 (GPIO_PORTF | GPIO_AF | 1)#define PF3_AF_ETMTRACE_PKT2 (GPIO_PORTF | GPIO_AF | 3)#define PF5_AF_ETMPIPESTAT11 (GPIO_PORTF | GPIO_AF | 5)
Signature · 1 line
1.6.0.4
PATCH 1/1 mx27: mxt_td60: Add USB Support
Quoted 7 lines · Alan Carvalho de Assis
This patch add USB support on i-MXT TD60 to Host1 and Host2 ports.
Signed-off-by Alan Carvalho de Assis <[email protected]>--- arch/arm/mach-mx2/Kconfig | 1 + arch/arm/mach-mx2/mxt_td60.c | 106 +++++++++++++++++++++++++++ arch/arm/plat-mxc/include/mach/iomux-mx27.h | 14 ++++
Changes to iomux-mx27.h should go in an extra patch, I think.
[...]
arch/arm/mach-mx2/mxt_td60.c static struct imxuart_platform_data uart_pdata[] = { · line 289
Quoted 8 lines
arch/arm/mach-mx2/mxt_td60.c +8
-0+static int isp1105_init (struct otg_transceiver *otg) +{ +mxc_gpio_mode (GPIO_PORTB |23 |GPIO_GPIO |GPIO_OUT ); +gpio_set_value (GPIO_PORTB +23 ,1 ); +mxc_gpio_mode (GPIO_PORTC |31 |GPIO_GPIO |GPIO_OUT ); +gpio_set_value (GPIO_PORTC +31 ,1 ); +return 0 ; +}
gpio_request() is needed here.
Quoted 21 lines
arch/arm/mach-mx2/mxt_td60.c +21
-0+static int isp1105_set_vbus (struct otg_transceiver *otg,bool on) +{ +if (on) +gpio_set_value (GPIO_PORTB +27 ,0 ); +else +gpio_set_value (GPIO_PORTB +27 ,1 ); + +return 0 ; +} + +static struct mxc_usbh_platform_data usbh1_pdata = { + .portsc =MXC_EHCI_MODE_UTMI |MXC_EHCI_SERIAL , + .flags =MXC_EHCI_POWER_PINS_ENABLED |MXC_EHCI_INTERFACE_SINGLE_UNI , +}; + +static int __init usbh1_init (void ) +{ +struct otg_transceiver *otg; + + otg =kzalloc (sizeof (*otg),GFP_KERNEL ); +if (!otg)
arch/arm/mach-mx2/mxt_td60.c static struct imxuart_platform_data uart_pdata[] = { · line 322
Quoted 10 lines
arch/arm/mach-mx2/mxt_td60.c +10
-0+return -ENOMEM ; + + otg->label ="ISP1105" ; + otg->init = isp1105_init; + otg->set_vbus = isp1105_set_vbus; + + usbh1_pdata.otg = otg; + +return mxc_register_device (&mxc_usbh1, &usbh1_pdata); +}
Ideally, you would make that a more generic driver of its own, which lives in drivers/usb/otg/ and is named something like 'transceiver-gpio'. You would instanciate it by passing a platform data struct to set the gpios you want it to use. This might sound overdone, but it would make your code reusable.
The calls to mxc_gpio_mode() would remain in your platform code, of course.
Daniel
PATCH 1/1 mx27: mxt_td60: Add USB Support
Hi Daniel,
Quoted 12 lines · Daniel Mack
Quoted 8 lines · Alan Carvalho de Assis
This patch add USB support on i-MXT TD60 to Host1 and Host2 ports.
Signed-off-by Alan Carvalho de Assis <[email protected]>--- arch/arm/mach-mx2/Kconfig | 1 + arch/arm/mach-mx2/mxt_td60.c | 106 +++++++++++++++++++++++++++ arch/arm/plat-mxc/include/mach/iomux-mx27.h | 14 ++++Changes to
iomux-mx27.hshould go in an extra patch, I think.
Yes, I agree.
Quoted 13 lines
[...]
arch/arm/mach-mx2/mxt_td60.c static struct imxuart_platform_data uart_pdata[] = { · line 289
Quoted 8 lines
arch/arm/mach-mx2/mxt_td60.c +8
-0+static int isp1105_init (struct otg_transceiver *otg) +{ +mxc_gpio_mode (GPIO_PORTB |23 |GPIO_GPIO |GPIO_OUT ); +gpio_set_value (GPIO_PORTB +23 ,1 ); +mxc_gpio_mode (GPIO_PORTC |31 |GPIO_GPIO |GPIO_OUT ); +gpio_set_value (GPIO_PORTC +31 ,1 ); +return 0 ; +}
gpio_request()is needed here.
Sure, I missed it.
Quoted 9 lines
Ideally, you would make that a more generic driver of its own, which lives in
drivers/usb/otg/and is named something like 'transceiver-gpio'. You would instanciate it by passing a platform data struct to set the gpios you want it
to use. This might sound overdone, but it would make your code reusable.The calls to
mxc_gpio_mode()would remain in your platform code, of course.
Ok, I need your support here. I'm using mxc-master and I looked for something related to "transceiver gpio", but no success. I found some gpio related to usb gadget, but this is not the case. Could you point me to right function?
Thank you very much,
Alan
Quoted 3 lines
Daniel
PATCH 1/1 mx27: mxt_td60: Add USB Support
Quoted 9 lines · Alan Carvalho de Assis
Quoted 9 lines · Alan Carvalho de Assis
Ideally, you would make that a more generic driver of its own, which lives in
drivers/usb/otg/and is named something like 'transceiver-gpio'. You would instanciate it by passing a platform data struct to set the gpios you want it
to use. This might sound overdone, but it would make your code reusable.
Quoted 7 lines
Quoted 2 lines
The calls to
mxc_gpio_mode()would remain in your platform code, of course.Ok, I need your support here. I'm using mxc-master and I looked for something related to "transceiver gpio", but no success. I found some gpio related to usb gadget, but this is not the case. Could you point me to right function?
What I was thinking of is a very small kind of driver that is initialized similar to the ulpi transceiver but instead of taking ULPI lowevel operations, it is fed with a struct to specify the GPIOs to use.
Daniel