drm: random hang since 620f378 "drm: prune modes when ..."
Subsystems (3)
After upgrading one of my machines to 2.6.32, I saw hangs after one to thirty minutes after booting, with random data written to parts of the frame buffer. I've bisected it down to 620f37811d "drm: prune modes when output is disconnected.", which was merged in 2.6.32-rc1. Connecting a serial console does not reveal any output at the time of the crash.
The machine uses an Intel G45 chipset with the i915 kernel mode setting enabled.
I have no clue what that patch does or why reverting it fixes the problem but 2.6.32 with this revert applied has not shown these hangs yet.
---
drivers/gpu/drm/drm_crtc_helper.c +2 -2
@@ -104,7 +104,8 @@ int drm_helper_probe_single_connector_modes(struct drm_connector *connector,if (connector->status == connector_status_disconnected) {DRM_DEBUG_KMS ("%s is disconnected\n" ,drm_get_connector_name (connector)); - goto prune; +/* TODO set EDID to NULL */ +return 0 ; } count = (*connector_funcs->get_modes)(connector);
@@ -132,7 +133,6 @@ int drm_helper_probe_single_connector_modes(struct drm_connector *connector, mode); } -prune:drm_mode_prune_invalid (dev, &connector->modes, true);if (list_empty (&connector->modes))
Quoted 6 lines · Arnd Bergmann
After upgrading one of my machines to 2.6.32, I saw hangs after one to thirty minutes after booting, with random data written to parts of the frame buffer. I've bisected it down to
620f37811d"drm: prune modes when output is disconnected.", which was merged in 2.6.32-rc1. Connecting a serial console does not reveal any output at the time of the crash.
Quoted 6 lines
The machine uses an Intel G45 chipset with the i915 kernel mode setting enabled.
I have no clue what that patch does or why reverting it fixes the problem but 2.6.32 with this revert applied has not shown these hangs yet.
Signed-off-by Arnd Bergmann <[email protected]>
Scratch this, the machine crashed again in the same way, but only after a some hours of uptime (normally it took a few minutes). It still looks like
this commit makes the bug much more likely, but it could also be
attributed to complete coincedence and bad timing. 2.6.31 certainly never showed the problem and the bisection clearly pointed in the general direction of i915.
I hate debugging sporadic hangs...
Sorry for blaming the wrong patch, especially if it already caused a lot of work. I'll try blaming ec2a4c3fdc8 "drm/i915: get the bridge device once" now, that is the next-best candidate that my bisection pointed to, but I'll do more rigorous testing.
Arnd
Quoted 21 lines · Arnd Bergmann
Quoted 6 lines · Arnd Bergmann
After upgrading one of my machines to 2.6.32, I saw hangs after one to thirty minutes after booting, with random data written to parts of the frame buffer. I've bisected it down to
620f37811d"drm: prune modes when output is disconnected.", which was merged in 2.6.32-rc1. Connecting a serial console does not reveal any output at the time of the crash.Quoted 6 lines
The machine uses an Intel G45 chipset with the i915 kernel mode setting enabled.
I have no clue what that patch does or why reverting it fixes the problem but 2.6.32 with this revert applied has not shown these hangs yet.
Signed-off-by Arnd Bergmann <[email protected]>Scratch this, the machine crashed again in the same way, but only after a some hours of uptime (normally it took a few minutes). It still looks like
this commit makes the bug much more likely, but it could also be
attributed to complete coincedence and bad timing. 2.6.31 certainly never showed the problem and the bisection clearly pointed in the general direction of i915.
Quoted 7 lines
I hate debugging sporadic hangs...
Sorry for blaming the wrong patch, especially if it already caused a lot of work. I'll try blaming
ec2a4c3fdc8"drm/i915: get the bridge device once" now, that is the next-best candidate that my bisection pointed to, but I'll do more rigorous testing.
Btw is this just a laptop with no monitor plugged in?
just want to rule out the patch you mentioned for any sort of memory corruption.
Dave.
Quoted 5 lines · Dave Airlie
Quoted 5 lines
Sorry for blaming the wrong patch, especially if it already caused a lot of work. I'll try blaming
ec2a4c3fdc8"drm/i915: get the bridge device once" now, that is the next-best candidate that my bisection pointed to, but I'll do more rigorous testing.
It just crashed again with both 620f378 and ec2a4c3fdc8 reverted as well, after about an hour of uptime.
Quoted 4 lines
Btw is this just a laptop with no monitor plugged in?
just want to rule out the patch you mentioned for any sort of memory corruption.
It's a desktop machine with three outputs, Asus P5Q-EM mainboard. VGA is not connected at all, DVI has an open-ended cable on it, i.e. no screen on it. HDMI is connected through a cheap passive HDMI multiswitch to the DVI-D input of a Lenovo screen.
Arnd
Quoted 12 lines · Arnd Bergmann
Quoted 5 lines · Dave Airlie
Quoted 5 lines
Sorry for blaming the wrong patch, especially if it already caused a lot of work. I'll try blaming
ec2a4c3fdc8"drm/i915: get the bridge device once" now, that is the next-best candidate that my bisection pointed to, but I'll do more rigorous testing.It just crashed again with both 620f378 and
ec2a4c3fdc8reverted as well, after about an hour of uptime.Quoted 2 lines
Btw is this just a laptop with no monitor plugged in?
Quoted 7 lines
Quoted 2 lines
just want to rule out the patch you mentioned for any sort of memory corruption.
It's a desktop machine with three outputs, Asus P5Q-EM mainboard. VGA is not connected at all, DVI has an open-ended cable on it, i.e. no screen on it. HDMI is connected through a cheap passive HDMI multiswitch to the DVI-D input of a Lenovo screen.
CC'ed the Intel ppl,
regression since 2.6.31 by the looks of it, bisection has found two false positives so far.
Dave.
Quoted 8 lines · On Wednesday 09 December 2009 05:38:07 Dave Airlie wrote:
Quoted 7 lines · Arnd Bergmann
Quoted 5 lines · Dave Airlie
Quoted 5 lines
Sorry for blaming the wrong patch, especially if it already caused a lot of work. I'll try blaming
ec2a4c3fdc8"drm/i915: get the bridge device once" now, that is the next-best candidate that my bisection pointed to, but I'll do more rigorous testing.
Quoted 7 lines
Quoted 3 lines
It just crashed again with both 620f378 and
ec2a4c3fdc8reverted as well, after about an hour of uptime....
regression since 2.6.31 by the looks of it, bisection has found two false positives so far.
I did a more thorough bisection this time, which points to c05422d52ee6b "drm/i915: remove open-coded drm_mode_object_find". The system crashed within minutes with 2.6.32-git and with c05422d52ee6b, but stayed up for 12 hours on identical kernels with this one reverted:
Quoted 10 lines
From
c05422d52ee6b4cff8b63eab1a7351780518fc5eMon Sep 17 00:00:00 2001
From: Daniel Vetter <[email protected]>
Date: Tue, 11 Aug 2009 16:05:30 +0200
Subject: [PATCH] drm/i915: remove open-codeddrm_mode_object_findAnd clean up a small whitespace goof-up in the same function, while I was looking at it.
Signed-off-by Daniel Vetter <[email protected]>Signed-off-by Eric Anholt <[email protected]>
Given that my last bisection went wrong and I can't prove why this patch is bad, I'd of course like to see some insight about what could go wrong here, but at least reverting it should not be able to cause any harm.
---
[PATCH] drm/i915: revert c05422d52 "remove open-coded drm_mode_object_find"
The patch was meant as a cleanup, but apparently caused random hangs on my machine.
drivers/gpu/drm/i915/intel_display.c +12 -8
@@ -3557,26 +3557,30 @@ int intel_get_pipe_from_crtc_id(struct drm_device *dev, void *data, {drm_i915_private_t *dev_priv = dev->dev_private;struct drm_i915_get_pipe_from_crtc_id *pipe_from_crtc_id = data; -struct drm_mode_object *drmmode_obj; -struct intel_crtc *crtc; +struct drm_crtc *crtc =NULL ; +int pipe =-1 ;if (!dev_priv) {DRM_ERROR ("called with no initialization\n" );return -EINVAL ; } - drmmode_obj =drm_mode_object_find (dev, pipe_from_crtc_id->crtc_id, -DRM_MODE_OBJECT_CRTC ); +list_for_each_entry (crtc, &dev->mode_config.crtc_list, head) { +struct intel_crtc *intel_crtc =to_intel_crtc (crtc); +if (crtc->base.id == pipe_from_crtc_id->crtc_id) { + pipe = intel_crtc->pipe; +break ; + } + } -if (!drmmode_obj) { +if (pipe ==-1 ) {DRM_ERROR ("no such CRTC id\n" );return -EINVAL ; } - crtc =to_intel_crtc (obj_to_crtc (drmmode_obj)); - pipe_from_crtc_id->pipe = crtc->pipe; + pipe_from_crtc_id->pipe = pipe; -return 0 ; +return 0 ; }struct drm_crtc *intel_get_crtc_from_pipe (struct drm_device *dev,int pipe)
Quoted 14 lines · On Sunday 13 December 2009 12:18:24 Arnd Bergmann wrote:
Quoted 13 lines · On Wednesday 09 December 2009 05:38:07 Dave Airlie wrote:
Quoted 10 lines · Arnd Bergmann
Quoted 5 lines · Dave Airlie
Quoted 5 lines
Sorry for blaming the wrong patch, especially if it already caused a lot of work. I'll try blaming
ec2a4c3fdc8"drm/i915: get the bridge device once" now, that is the next-best candidate that my bisection pointed to, but I'll do more rigorous testing.It just crashed again with both 620f378 and
ec2a4c3fdc8reverted as well, after about an hour of uptime....
Quoted 12 lines
Quoted 2 lines
regression since 2.6.31 by the looks of it, bisection has found two false positives so far.
I did a more thorough bisection this time, which points to
c05422d52ee6b"drm/i915: remove open-codeddrm_mode_object_find". The system crashed within minutes with 2.6.32-git and withc05422d52ee6b, but stayed up for 12 hours on identical kernels with this one reverted:Quoted 4 lines
From
c05422d52ee6b4cff8b63eab1a7351780518fc5eMon Sep 17 00:00:00 2001
From: Daniel Vetter <[email protected]>
Date: Tue, 11 Aug 2009 16:05:30 +0200
Subject: [PATCH] drm/i915: remove open-codeddrm_mode_object_find
And now it's obvious that my computer hates me. 12 hours of uptime, one reboot to check the old other version is broken, it crashes. I reboot into the good version, send out the above email and the next minute it crashes again. c05422d52ee6b is not the culprit. Sorry Daniel for blaming your patch.
Arnd
Quoted 4 lines · Arnd Bergmann
And now it's obvious that my computer hates me. 12 hours of uptime, one reboot to check the old other version is broken, it crashes. I reboot into the good version, send out the above email and the next minute it crashes again.
c05422d52ee6bis not the culprit. Sorry Daniel for blaming your patch.
No problem. Looks like your hunting a pretty ugly Heisenbug. There's quite a interesting blog post by Paul McKenney, esp. the solution to "Quick Quiz 1" might be usefull in your case:
http://paulmck.livejournal.com/14639.html
Happy Hunting, Daniel
Signature · 3 lines
Daniel Vetter Mail: [email protected] Mobile: +41 (0)79 365 57 48
Quoted 11 lines · On Sunday 13 December 2009 20:00:18 Daniel Vetter wrote:
Quoted 4 lines · Arnd Bergmann
And now it's obvious that my computer hates me. 12 hours of uptime, one reboot to check the old other version is broken, it crashes. I reboot into the good version, send out the above email and the next minute it crashes again.
c05422d52ee6bis not the culprit. Sorry Daniel for blaming your patch.No problem. Looks like your hunting a pretty ugly Heisenbug. There's quite a interesting blog post by Paul McKenney, esp. the solution to "Quick Quiz 1" might be usefull in your case:
Thanks! In fact I've actually read that post on the kernel planet and decided to do basically a linear search through the i915 patches merged into 2.6.32.
The current result is 67cf781bea5 "drm/i915: Make the downclocking debug code be under DRM_DEBUG not DRM_ERROR." is known bad, while 043029655 "drm/i915:
Support IGD EOS" is probably good, pointing to Jesses 652c393a33 "drm/i915:
add dynamic clock frequency control" as the next best guess. Unfortunately, that is a rather large change that is not easy to revert on current kernels.
I'll keep running my machine on the 043029655 level and tell you if it keeps working a few more days.
Arnd
Quoted 13 lines · Arnd Bergmann
Quoted 11 lines · On Sunday 13 December 2009 20:00:18 Daniel Vetter wrote:
Quoted 4 lines · Arnd Bergmann
And now it's obvious that my computer hates me. 12 hours of uptime, one reboot to check the old other version is broken, it crashes. I reboot into the good version, send out the above email and the next minute it crashes again.
c05422d52ee6bis not the culprit. Sorry Daniel for blaming your patch.No problem. Looks like your hunting a pretty ugly Heisenbug. There's quite a interesting blog post by Paul McKenney, esp. the solution to "Quick Quiz 1" might be usefull in your case:
Quoted 8 lines
Thanks! In fact I've actually read that post on the kernel planet and decided to do basically a linear search through the i915 patches merged into 2.6.32.
The current result is
67cf781bea5"drm/i915: Make the downclocking debug code be underDRM_DEBUGnotDRM_ERROR." is known bad, while 043029655 "drm/i915:
Support IGD EOS" is probably good, pointing to Jesses652c393a33"drm/i915:
add dynamic clock frequency control" as the next best guess. Unfortunately, that is a rather large change that is not easy to revert on current kernels.
That seems the most likely, perhaps jbarnes can comment.
Dave.
Quoted 19 lines · On Mon, 14 Dec 2009 07:54:05 +1000 Dave Airlie <[email protected]> wrote:
Quoted 18 lines · Arnd Bergmann
Quoted 7 lines · On Sunday 13 December 2009 20:00:18 Daniel Vetter wrote:
Quoted 5 lines · Arnd Bergmann
And now it's obvious that my computer hates me. 12 hours of uptime, one reboot to check the old other version is broken, it crashes. I reboot into the good version, send out the above email and the next minute it crashes again.
c05422d52ee6bis not the culprit. Sorry Daniel for blaming your patch.Quoted 5 lines
No problem. Looks like your hunting a pretty ugly Heisenbug. There's quite a interesting blog post by Paul McKenney, esp. the solution to "Quick Quiz 1" might be usefull in your case:
Thanks! In fact I've actually read that post on the kernel planet and decided to do basically a linear search through the i915 patches merged into 2.6.32.
Quoted 8 lines
Quoted 6 lines
The current result is
67cf781bea5"drm/i915: Make the downclocking debug code be underDRM_DEBUGnotDRM_ERROR." is known bad, while 043029655 "drm/i915: Support IGD EOS" is probably good, pointing to Jesses652c393a33"drm/i915: add dynamic clock frequency control" as the next best guess. Unfortunately, that is a rather large change that is not easy to revert on current kernels.That seems the most likely, perhaps jbarnes can comment.
You can disable most of that code by loading i915 with 'powersave=0'. If that patch really is at fault the powersave=0 should work around the issue as well.
It's been implicated in another issue (some display flicker and underruns) so I'm pretty sure there's something wrong with it in some configurations at least...
Signature · 1 line
Jesse Barnes, Intel Open Source Technology Center
Quoted 3 lines · On Monday 14 December 2009 18:20:15 Jesse Barnes wrote:
You can disable most of that code by loading i915 with 'powersave=0'. If that patch really is at fault the powersave=0 should work around the issue as well.
Ok, I'll try that and let you know. Running the kernel before your patch has not crashed yet after two days of uptime. Now running with your patch but nothing else. When that crashes, I'll try the latest mainline with powersave=0.
Quoted 3 lines
It's been implicated in another issue (some display flicker and underruns) so I'm pretty sure there's something wrong with it in some configurations at least...
I haven't seen that yet. FWIW, the device in question is
00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03)
Subsystem: ASUSTeK Computer Inc. Device 8276
Flags: bus master, fast devsel, latency 0, IRQ 27
Memory at fe400000 (64-bit, non-prefetchable) [size=4M]
Memory at d0000000 (64-bit, prefetchable) [size=256M]
I/O ports at cc00 [size=8]
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable+
Capabilities: [d0] Power Management version 2
Capabilities: [a4] PCIe advanced features <?>
Kernel driver in use: i915
00: 86 80 22 2e 07 04 90 00 03 00 00 03 00 00 80 00
10: 04 00 40 fe 00 00 00 00 0c 00 00 d0 00 00 00 00
20: 01 cc 00 00 00 00 00 00 00 00 00 00 43 10 76 82
30: 00 00 00 00 90 00 00 00 00 00 00 00 0a 01 00 00
00:02.1 Display controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03)
Subsystem: ASUSTeK Computer Inc. Device 8276
Flags: bus master, fast devsel, latency 0
Memory at fe800000 (64-bit, non-prefetchable) [size=1M]
Capabilities: [d0] Power Management version 2
00: 86 80 23 2e 07 00 90 00 03 00 80 03 00 00 80 00
10: 04 00 80 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 76 82
30: 00 00 00 00 d0 00 00 00 00 00 00 00 00 00 00 00
Let me know if you have a patch you want me to test.
Thanks,
Arnd
Quoted 9 lines · On Mon, 14 Dec 2009 20:38:09 +0000 Arnd Bergmann <[email protected]> wrote:
Quoted 3 lines · On Monday 14 December 2009 18:20:15 Jesse Barnes wrote:
You can disable most of that code by loading i915 with 'powersave=0'. If that patch really is at fault the powersave=0 should work around the issue as well.
Ok, I'll try that and let you know. Running the kernel before your patch has not crashed yet after two days of uptime. Now running with your patch but nothing else. When that crashes, I'll try the latest mainline with powersave=0.
Ok great.
Quoted 5 lines
Quoted 3 lines
It's been implicated in another issue (some display flicker and underruns) so I'm pretty sure there's something wrong with it in some configurations at least...
I haven't seen that yet. FWIW, the device in question is
[snip 4 series pci info]
Quoted 1 line
Let me know if you have a patch you want me to test.
This patch removes the suspect portion of the dynamic clock control code. Hopefully it'll be as stable as powersave=0 in your config (assuming powersave=0 works :).
Signature · 1 line
Jesse Barnes, Intel Open Source Technology Center
drivers/gpu/drm/i915/intel_display.c +0 -2
@@ -3825,8 +3825,6 @@ void intel_decrease_renderclock(struct drm_device *dev)/* Down to minimum... */ gcfgc &= ~GM45_GC_RENDER_CLOCK_MASK ; gcfgc |=GM45_GC_RENDER_CLOCK_266_MHZ ; - -pci_write_config_word (dev->pdev,GCFGC , gcfgc); }else if (IS_I965G (dev)) {u16 gcfgc;
Quoted 3 lines · Jesse Barnes
This patch removes the suspect portion of the dynamic clock control code. Hopefully it'll be as stable as powersave=0 in your config (assuming powersave=0 works :).
Ok, great! The machine is still running fine with powersave=0 so far. I'll try your patch after some more uptime.
Arnd
Quoted 14 lines
Jesse Barnes, Intel Open Source Technology Center
drivers/gpu/drm/i915/intel_display.c +0
-2@@ -3825,8 +3825,6 @@ void intel_decrease_renderclock(struct drm_device *dev)/* Down to minimum... */ gcfgc &= ~GM45_GC_RENDER_CLOCK_MASK ; gcfgc |=GM45_GC_RENDER_CLOCK_266_MHZ ; - -pci_write_config_word (dev->pdev,GCFGC , gcfgc); }else if (IS_I965G (dev)) {u16 gcfgc;
Quoted 7 lines · Arnd Bergmann
Quoted 3 lines · Jesse Barnes
This patch removes the suspect portion of the dynamic clock control code. Hopefully it'll be as stable as powersave=0 in your config (assuming powersave=0 works :).
Ok, great! The machine is still running fine with powersave=0 so far. I'll try your patch after some more uptime.
It's working fine so far, no more crashes, but I supposed this effectively disables the power saving on my card again, right?
I should probably mention that this machine has had stability problems before and showed single-bit memory corruption, but that problem has disappeared after I installed bigger CPU and northbridge coolers and increased the voltage slightly.
Arnd
Quoted 11 lines · On Wed, 16 Dec 2009 14:53:11 +0100 Arnd Bergmann <[email protected]> wrote:
Quoted 7 lines · Arnd Bergmann
Quoted 3 lines · Jesse Barnes
This patch removes the suspect portion of the dynamic clock control code. Hopefully it'll be as stable as powersave=0 in your config (assuming powersave=0 works :).
Ok, great! The machine is still running fine with powersave=0 so far. I'll try your patch after some more uptime.
It's working fine so far, no more crashes, but I supposed this effectively disables the power saving on my card again, right?
The patch just disables one (probably ineffective) power saving feature. So if things are working well for you with it I'll queue up a revert patch. I'm working on a better version of dynamic clock control anyway.
Signature · 1 line
Jesse Barnes, Intel Open Source Technology Center
Quoted 10 lines · On Wednesday 16 December 2009 20:18:23 Jesse Barnes wrote:
Quoted 2 lines · On Wed, 16 Dec 2009 14:53:11 +0100 Arnd Bergmann <[email protected]> wrote:
It's working fine so far, no more crashes, but I supposed this effectively disables the power saving on my card again, right?
The patch just disables one (probably ineffective) power saving feature. So if things are working well for you with it I'll queue up a revert patch. I'm working on a better version of dynamic clock control anyway.
It just crashed again after a few hours of uptime with some unrelated reboots in-between, with your patch applied.
The symptom was slightly different, now the whole screen was filled with random patterns, not just parts of the screen. Aside from that, it was just the same complete lockup as without the patch. Possibly less frequent, but that's hard to tell after a single sample.
Arnd
Quoted 12 lines · On Wed, 16 Dec 2009 21:20:34 +0000 Arnd Bergmann <[email protected]> wrote:
Quoted 10 lines · On Wednesday 16 December 2009 20:18:23 Jesse Barnes wrote:
Quoted 2 lines · On Wed, 16 Dec 2009 14:53:11 +0100 Arnd Bergmann <[email protected]> wrote:
It's working fine so far, no more crashes, but I supposed this effectively disables the power saving on my card again, right?
The patch just disables one (probably ineffective) power saving feature. So if things are working well for you with it I'll queue up a revert patch. I'm working on a better version of dynamic clock control anyway.
Quoted 7 lines
It just crashed again after a few hours of uptime with some unrelated reboots in-between, with your patch applied.
The symptom was slightly different, now the whole screen was filled with random patterns, not just parts of the screen. Aside from that, it was just the same complete lockup as without the patch. Possibly less frequent, but that's hard to tell after a single sample.
But you're sure powersave=0 was solid? Hmm...
Signature · 1 line
Jesse Barnes, Intel Open Source Technology Center
Quoted 1 line · On Wednesday 16 December 2009 21:30:05 Jesse Barnes wrote:
But you're sure powersave=0 was solid? Hmm...
It's hard to be sure when it sometimes takes a day before a broken version crashes. I can keep running this kernel with and without powersave=0 some more and tell you if it stays reproducible.
Arnd
Quoted 6 lines · On Wednesday 16 December 2009 21:36:36 Arnd Bergmann wrote:
Quoted 1 line · On Wednesday 16 December 2009 21:30:05 Jesse Barnes wrote:
But you're sure powersave=0 was solid? Hmm...
It's hard to be sure when it sometimes takes a day before a broken version crashes. I can keep running this kernel with and without powersave=0 some more and tell you if it stays reproducible.
Now it has crashed with i915.powersave=0 plus your patch as well (latest 2.6.32 git), indicating that there is something else wrong with the original 652c393a33 patch.
Arnd
Quoted 11 lines · On Wed, 16 Dec 2009 22:41:27 +0000 Arnd Bergmann <[email protected]> wrote:
Quoted 6 lines · On Wednesday 16 December 2009 21:36:36 Arnd Bergmann wrote:
Quoted 1 line · On Wednesday 16 December 2009 21:30:05 Jesse Barnes wrote:
But you're sure powersave=0 was solid? Hmm...
It's hard to be sure when it sometimes takes a day before a broken version crashes. I can keep running this kernel with and without powersave=0 some more and tell you if it stays reproducible.
Now it has crashed with i915.powersave=0 plus your patch as well (latest 2.6.32 git), indicating that there is something else wrong with the original
652c393a33patch.
It does very little else that should affect things. You're sure reverting the commit makes things ok?
Other potential problems:
- clock gating (the call to intel_init_clock_gating)
- the actual mark_busy stuff itself (calls to intel_mark_busy)
- intel_idle_update (but powersave=0 should prevent that)
If you want to keep testing you could try removing those calls...
Signature · 1 line
Jesse Barnes, Intel Open Source Technology Center
Quoted 2 lines · Jesse Barnes
It does very little else that should affect things. You're sure reverting the commit makes things ok?
No, not sure. But I've been running the kernel before that commit for days without ever seeing a crash. 2.6.31 (also without that commit but otherwise pretty similar) has been stable for weeks weeks on the same box.
Once any given kernel version crashes, which can take up to a day while I'm waiting for the bug to show up, it will typically crash on that same kernel again within seconds after boot, just to annoy me and prevent me from using that kernel for other things.
Quoted 6 lines
Other potential problems:
- clock gating (the call tointel_init_clock_gating)
- the actualmark_busystuff itself (calls tointel_mark_busy)
-intel_idle_update(but powersave=0 should prevent that)If you want to keep testing you could try removing those calls...
Ok, I'll try that. The problem is keeping me from doing any useful upstream kernel work on my main machine, so I'm rather motivated ;-)
Arnd
Quoted 20 lines · On Thu, 17 Dec 2009 18:52:02 +0100 Arnd Bergmann <[email protected]> wrote:
Quoted 2 lines · Jesse Barnes
It does very little else that should affect things. You're sure reverting the commit makes things ok?
No, not sure. But I've been running the kernel before that commit for days without ever seeing a crash. 2.6.31 (also without that commit but otherwise pretty similar) has been stable for weeks weeks on the same box.
Once any given kernel version crashes, which can take up to a day while I'm waiting for the bug to show up, it will typically crash on that same kernel again within seconds after boot, just to annoy me and prevent me from using that kernel for other things.
Quoted 5 lines
Other potential problems:
- clock gating (the call tointel_init_clock_gating)
- the actualmark_busystuff itself (calls tointel_mark_busy)
-intel_idle_update(but powersave=0 should prevent that)
Quoted 4 lines
Quoted 1 line
If you want to keep testing you could try removing those calls...
Ok, I'll try that. The problem is keeping me from doing any useful upstream kernel work on my main machine, so I'm rather motivated ;-)
Another patch to try...
drivers/gpu/drm/i915/intel_display.c +2 -130
@@ -3779,125 +3779,6 @@ static void intel_gpu_idle_timer(unsigned long arg)queue_work (dev_priv->wq, &dev_priv->idle_work); } -void intel_increase_renderclock (struct drm_device *dev,bool schedule) -{ -drm_i915_private_t *dev_priv = dev->dev_private; - -if (IS_IRONLAKE (dev)) -return ; - -if (!dev_priv->render_reclock_avail) { -DRM_DEBUG_DRIVER ("not reclocking render clock\n" ); -return ; - } - -/* Restore render clock frequency to original value */ -if (IS_G4X (dev) ||IS_I9XX (dev)) -pci_write_config_word (dev->pdev,GCFGC , dev_priv->orig_clock); -else if (IS_I85X (dev)) -pci_write_config_word (dev->pdev,HPLLCC , dev_priv->orig_clock); -DRM_DEBUG_DRIVER ("increasing render clock frequency\n" ); - -/* Schedule downclock */ -if (schedule) -mod_timer (&dev_priv->idle_timer, jiffies + -msecs_to_jiffies (GPU_IDLE_TIMEOUT )); -} - -void intel_decrease_renderclock (struct drm_device *dev) -{ -drm_i915_private_t *dev_priv = dev->dev_private; - -if (IS_IRONLAKE (dev)) -return ; - -if (!dev_priv->render_reclock_avail) { -DRM_DEBUG_DRIVER ("not reclocking render clock\n" ); -return ; - } - -if (IS_G4X (dev)) { -u16 gcfgc; - -/* Adjust render clock... */ -pci_read_config_word (dev->pdev,GCFGC , &gcfgc); - -/* Down to minimum... */ - gcfgc &= ~GM45_GC_RENDER_CLOCK_MASK ; - gcfgc |=GM45_GC_RENDER_CLOCK_266_MHZ ; - -pci_write_config_word (dev->pdev,GCFGC , gcfgc); - }else if (IS_I965G (dev)) { -u16 gcfgc; - -/* Adjust render clock... */ -pci_read_config_word (dev->pdev,GCFGC , &gcfgc); - -/* Down to minimum... */ - gcfgc &= ~I965_GC_RENDER_CLOCK_MASK ; - gcfgc |=I965_GC_RENDER_CLOCK_267_MHZ ; - -pci_write_config_word (dev->pdev,GCFGC , gcfgc); - }else if (IS_I945G (dev) ||IS_I945GM (dev)) { -u16 gcfgc; - -/* Adjust render clock... */ -pci_read_config_word (dev->pdev,GCFGC , &gcfgc); - -/* Down to minimum... */ - gcfgc &= ~I945_GC_RENDER_CLOCK_MASK ; - gcfgc |=I945_GC_RENDER_CLOCK_166_MHZ ; - -pci_write_config_word (dev->pdev,GCFGC , gcfgc); - }else if (IS_I915G (dev)) { -u16 gcfgc; - -/* Adjust render clock... */ -pci_read_config_word (dev->pdev,GCFGC , &gcfgc); - -/* Down to minimum... */ - gcfgc &= ~I915_GC_RENDER_CLOCK_MASK ; - gcfgc |=I915_GC_RENDER_CLOCK_166_MHZ ; - -pci_write_config_word (dev->pdev,GCFGC , gcfgc); - }else if (IS_I85X (dev)) { -u16 hpllcc; - -/* Adjust render clock... */ -pci_read_config_word (dev->pdev,HPLLCC , &hpllcc); - -/* Up to maximum... */ - hpllcc &= ~GC_CLOCK_CONTROL_MASK ; - hpllcc |=GC_CLOCK_133_200 ; - -pci_write_config_word (dev->pdev,HPLLCC , hpllcc); - } -DRM_DEBUG_DRIVER ("decreasing render clock frequency\n" ); -} - -/* Note that no increase function is needed for this - increase_renderclock() -* will also rewrite these bits -*/ -void intel_decrease_displayclock (struct drm_device *dev) -{ -if (IS_IRONLAKE (dev)) -return ; - -if (IS_I945G (dev) ||IS_I945GM (dev) ||IS_I915G (dev) || -IS_I915GM (dev)) { -u16 gcfgc; - -/* Adjust render clock... */ -pci_read_config_word (dev->pdev,GCFGC , &gcfgc); - -/* Down to minimum... */ - gcfgc &= ~0xf0 ; - gcfgc |=0x80 ; - -pci_write_config_word (dev->pdev,GCFGC , gcfgc); - } -} -#define CRTC_IDLE_TIMEOUT 1000/* ms */ static void intel_crtc_idle_timer (unsigned long arg)
@@ -4011,12 +3892,6 @@ static void intel_idle_update(struct work_struct *work)mutex_lock (&dev->struct_mutex); -/* GPU isn't processing, downclock it. */ -if (!dev_priv->busy) { -intel_decrease_renderclock (dev); -intel_decrease_displayclock (dev); - } -list_for_each_entry (crtc, &dev->mode_config.crtc_list, head) {/* Skip inactive CRTCs */ if (!crtc->fb)
@@ -4050,13 +3925,11 @@ void intel_mark_busy(struct drm_device *dev, struct drm_gem_object *obj)if (!drm_core_check_feature (dev,DRIVER_MODESET ))return ; -if (!dev_priv->busy) { +if (!dev_priv->busy) dev_priv->busy = true; -intel_increase_renderclock (dev, true); - }else { +else mod_timer (&dev_priv->idle_timer, jiffies +msecs_to_jiffies (GPU_IDLE_TIMEOUT )); - }list_for_each_entry (crtc, &dev->mode_config.crtc_list, head) {if (!crtc->fb)
@@ -4770,7 +4643,6 @@ void intel_modeset_cleanup(struct drm_device *dev)del_timer_sync (&intel_crtc->idle_timer); } -intel_increase_renderclock (dev, false);del_timer_sync (&dev_priv->idle_timer);if (dev_priv->display.disable_fbc)
Quoted 4 lines · On Thursday 17 December 2009 19:13:59 Jesse Barnes wrote:
Quoted 2 lines
Ok, I'll try that. The problem is keeping me from doing any useful upstream kernel work on my main machine, so I'm rather motivated ;-)
Another patch to try...
Thanks!
It's running fine so far, uptime 90 minutes together with powersave=0. I'll keep the machine running and tell you if it crashes again later.
Arnd
Quoted 1 line · On Thursday 17 December 2009 19:13:59 Jesse Barnes wrote:
Another patch to try...
The machine has been working fine for almost two days with this.
Review
Quoted 12 lines
(quoted diff) +0
-12- - if (IS_G4X(dev)) { - u16 gcfgc; - - /* Adjust render clock... */ - pci_read_config_word(dev->pdev, GCFGC, &gcfgc); - - /* Down to minimum... */ - gcfgc &= ~GM45_GC_RENDER_CLOCK_MASK; - gcfgc |= GM45_GC_RENDER_CLOCK_266_MHZ; - - pci_write_config_word(dev->pdev, GCFGC, gcfgc);
Interestingly, I could not even find GCFGC in the public documentation, but it also doesn't seem to be what it was in older chips.
The value in there is 0x0025, which does not make any sense whatsoever according to the definitions in the header file. Writing GM45_GC_RENDER_CLOCK_266_MHZ in there manually does not seem to have an effect either, the machine does not crash and the value still remains at 0x0025.
I tried "while true ; do sudo setpci -s 00:02.1 f0.W=0028 ; done".
I'll try the patch below next, not touching the register at all.
Quoted 12 lines
(quoted diff) +0
-12-/* Note that no increase function is needed for this - increase_renderclock() - * will also rewrite these bits - */ -void intel_decrease_displayclock(struct drm_device *dev) -{ - if (IS_IRONLAKE(dev)) - return; - - if (IS_I945G(dev) || IS_I945GM(dev) || IS_I915G(dev) || - IS_I915GM(dev)) { - u16 gcfgc; -
Review
Quoted 10 lines
(quoted diff) +0
-10- /* Adjust render clock... */ - pci_read_config_word(dev->pdev, GCFGC, &gcfgc); - - /* Down to minimum... */ - gcfgc &= ~0xf0; - gcfgc |= 0x80; - - pci_write_config_word(dev->pdev, GCFGC, gcfgc); - } -}
This does not do anything on G4X, right? I actually put this function back in (still doesn't crash), but then I noticed that the registers are not accessed at all on my machine in this function.
Arnd
drivers/gpu/drm/i915/intel_display.c +2 -13
@@ -3792,7 +3792,7 @@ void intel_increase_renderclock(struct drm_device *dev, bool schedule) }/* Restore render clock frequency to original value */ -if (IS_G4X (dev) ||IS_I9XX (dev)) +if (IS_I9XX (dev))pci_write_config_word (dev->pdev,GCFGC , dev_priv->orig_clock);else if (IS_I85X (dev))pci_write_config_word (dev->pdev,HPLLCC , dev_priv->orig_clock);
@@ -3816,18 +3816,7 @@ void intel_decrease_renderclock(struct drm_device *dev)return ; } -if (IS_G4X (dev)) { -u16 gcfgc; - -/* Adjust render clock... */ -pci_read_config_word (dev->pdev,GCFGC , &gcfgc); - -/* Down to minimum... */ - gcfgc &= ~GM45_GC_RENDER_CLOCK_MASK ; - gcfgc |=GM45_GC_RENDER_CLOCK_266_MHZ ; - -pci_write_config_word (dev->pdev,GCFGC , gcfgc); - }else if (IS_I965G (dev)) { +if (IS_I965G (dev)) {u16 gcfgc;/* Adjust render clock... */
Quoted 5 lines · On Monday 21 December 2009 16:06:43 Arnd Bergmann wrote:
(quoted diff) +0
-4- if (IS_G4X(dev)) { - u16 gcfgc; - - /* Adjust render clock... */
Review
Quoted 10 lines
(quoted diff) +1
-8- pci_read_config_word(dev->pdev, GCFGC, &gcfgc); - - /* Down to minimum... */ - gcfgc &= ~GM45_GC_RENDER_CLOCK_MASK; - gcfgc |= GM45_GC_RENDER_CLOCK_266_MHZ; - - pci_write_config_word(dev->pdev, GCFGC, gcfgc); - } else if (IS_I965G(dev)) { + if (IS_I965G(dev)) { u16 gcfgc;
This crashed again immediately, apparently because IS_I965G is a superset of IS_G4X (that seems counterintuitive), but not it seems to run using this modified version of the patch (half an hour so far).
Arnd
drivers/gpu/drm/i915/intel_display.c +4 -13
@@ -3783,7 +3783,7 @@ void intel_increase_renderclock(struct drm_device *dev, bool schedule) {drm_i915_private_t *dev_priv = dev->dev_private; -if (IS_IRONLAKE (dev)) +if (IS_IRONLAKE (dev) ||IS_G4X (dev))return ;if (!dev_priv->render_reclock_avail) {
@@ -3792,7 +3792,7 @@ void intel_increase_renderclock(struct drm_device *dev, bool schedule) }/* Restore render clock frequency to original value */ -if (IS_G4X (dev) ||IS_I9XX (dev)) +if (IS_I9XX (dev))pci_write_config_word (dev->pdev,GCFGC , dev_priv->orig_clock);else if (IS_I85X (dev))pci_write_config_word (dev->pdev,HPLLCC , dev_priv->orig_clock);
@@ -3808,7 +3808,7 @@ void intel_decrease_renderclock(struct drm_device *dev) {drm_i915_private_t *dev_priv = dev->dev_private; -if (IS_IRONLAKE (dev)) +if (IS_IRONLAKE (dev) ||IS_G4X (dev))return ;if (!dev_priv->render_reclock_avail) {
@@ -3816,16 +3816,7 @@ void intel_decrease_renderclock(struct drm_device *dev)return ; } -if (IS_G4X (dev)) { -u16 gcfgc; - -/* Adjust render clock... */ -pci_read_config_word (dev->pdev,GCFGC , &gcfgc); - -/* Down to minimum... */ - gcfgc &= ~GM45_GC_RENDER_CLOCK_MASK ; - gcfgc |=GM45_GC_RENDER_CLOCK_266_MHZ ; - }else if (IS_I965G (dev)) { +if (IS_I965G (dev)) {u16 gcfgc;/* Adjust render clock... */
Quoted 12 lines · On Mon, 21 Dec 2009 17:57:08 +0000 Arnd Bergmann <[email protected]> wrote:
Quoted 11 lines · On Monday 21 December 2009 16:06:43 Arnd Bergmann wrote:
drivers/gpu/drm/i915/intel_display.c +0
-10-if (IS_G4X (dev)) { -u16 gcfgc; - -/* Adjust render clock... */ -pci_read_config_word (dev->pdev,GCFGC , &gcfgc); - -/* Down to minimum... */ - gcfgc &= ~GM45_GC_RENDER_CLOCK_MASK ; - gcfgc |=GM45_GC_RENDER_CLOCK_266_MHZ ; -
Quoted 9 lines
drivers/gpu/drm/i915/intel_display.c void intel_decrease_renderclock(struct drm_device *dev) · line 3820
Quoted 4 lines
drivers/gpu/drm/i915/intel_display.c +1
-2-pci_write_config_word (dev->pdev,GCFGC , gcfgc); - }else if (IS_I965G (dev)) { +if (IS_I965G (dev)) {u16 gcfgc;This crashed again immediately, apparently because
IS_I965Gis a superset ofIS_G4X(that seems counterintuitive), but not it seems to run using this modified version of the patch (half an hour so far).
This code should be completely gone in Eric's drm-intel-next branch (fromgit://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel.git), so hopefully when that lands upstream (if it hasn't already) things will be solid for you.
Thanks,
Jesse
Quoted 5 lines · Jesse Barnes
This code should be completely gone in Eric's drm-intel-next branch (from
git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel.git), so hopefully when that lands upstream (if it hasn't already) things will be solid for you.
Unfortunately, it seems it did not help. I could also reproduce the hang with your patch that I reported working for two days before Christmas, and with the version of that patch that I posted later. I'm running 04302965 again now, and try to apply other parts of the patch that introduced the regression.
Arnd
Hi,
Quoted 8 lines
You can disable most of that code by loading i915 with 'powersave=0'. If that patch really is at fault the powersave=0 should work around the issue as well.
It's been implicated in another issue (some display flicker and underruns) so I'm pretty sure there's something wrong with it in some configurations at least...
Could it be also that the powersave feature produces gpu hangs when xserver is run the first time (after a cold boot). I have serious issues the intel drm starting at v2.6.32-rc2 (I can not use the v2.6.32 series on my laptop) while the same xorg stack works well with the v2.6.31 series. I try to bisect this problem and obtained this (sorry it is a bit long):
git bisect start 'drivers/gpu' 'arch/x86_64/'
# bad: [053fe57ac249a9531c396175778160d9e9509399] Merge git://git.kernel.org/pub
/scm/linux/kernel/git/davem/net-2.6
git bisect bad 053fe57ac249a9531c396175778160d9e9509399
# good: [74fca6a42863ffacaf7ba6f1936a9f228950f657] Linux 2.6.31
git bisect good 74fca6a42863ffacaf7ba6f1936a9f228950f657
# bad: [d8a2d0e00c0d5a0d55e14b884bff034205015e51] drm/i915: HDMI hardware workar ound for Ironlake
git bisect bad d8a2d0e00c0d5a0d55e14b884bff034205015e51
# bad: [d50ba256b5f1478e15accfcfda9b72fd7a661364] drm/kms: start adding command line interface using fb.
git bisect bad d50ba256b5f1478e15accfcfda9b72fd7a661364
# good: [551ebd837c75fc75df81811a18b7136c39cab487] drm/radeon/kms: add rn50/r100 /r200 CS tracker.
git bisect good 551ebd837c75fc75df81811a18b7136c39cab487
# good: [fdd5cace733370ab7a518a98ef084e02aa76fdea] drm/radeon/kms: Don't kzalloc
memory which is immediately overwritten.
git bisect good fdd5cace733370ab7a518a98ef084e02aa76fdea
# good: [698443d9ec1a33eff65b27b9514e06998bf57eb3] drm/radeon/kms: disable VGA r endering engine before taking over VRAM
git bisect good 698443d9ec1a33eff65b27b9514e06998bf57eb3
# good: [c214271563c00f2721c5111e27b53bf06dabc6e4] drm/radeon: consolidate famil y flags used in pciids.
git bisect good c214271563c00f2721c5111e27b53bf06dabc6e4
# good: [93dc6c2b0d97a55508144073838e041140b206cd] drm/edid: Detailed standard t iming blocks have six timings, not five.
git bisect good 93dc6c2b0d97a55508144073838e041140b206cd
# good: [4bbd4973703bf8a5f00f05eff30a99cd9814f37f] drm/radeon/kms: enable r600 t v outputs.
git bisect good 4bbd4973703bf8a5f00f05eff30a99cd9814f37f
# good: [513bcb4655e68706594e45dfa1d4b181500110ba] drm/radeon/kms: don't require
up to 64k allocations. (v2)
git bisect good 513bcb4655e68706594e45dfa1d4b181500110ba
Regards
Mathieu