Adding PCI-E support for PowerPC 460SX based SOC.
Subsystems (2)
PATCH 1/2 Adding PCI-E support for PowerPC 460SX based SOC.
From: Tirumala Marri <[email protected]>
---
Kerenl:2.6.33-rc1
Testing: This patch has been tested on 460SX based redwood board . One board configured as root complex and other as Endpoint. Checked for link up . From root complex lspci command shows the end point. Also programmed IO tested using loop back as well as board to board.
--- arch/powerpc/boot/dts/redwood.dts | 122 +++++++++++++++++++++++++++++++++++++ arch/powerpc/sysdev/ppc4xx_pci.c | 119 ++++++++++++++++++++++++++++++++++++ arch/powerpc/sysdev/ppc4xx_pci.h | 58 +++++++++++++++++ 3 files changed, 299 insertions(+), 0 deletions(-)
arch/powerpc/boot/dts/redwood.dts +122 -0
@@ -234,10 +234,132 @@ has-inverted-stacr-oc; has-new-stacr-staopc; }; + }; + PCIE0: pciex@d00000000 { + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "ibm,plb-pciex-460sx", "ibm,plb-pciex"; + primary; + port = <0x0>; /* port number */ + reg = <0x0000000d 0x00000000 0x20000000 /* Config space access */ + 0x0000000c 0x10000000 0x00001000>; /* Registers */ + dcr-reg = <0x100 0x020>; + sdr-base = <0x300>; + + /* Outbound ranges, one memory and one IO, + * later cannot be changed + */ + ranges = <0x02000000 0x00000000 0x80000000 0x0000000e 0x00000000 0x00000000 0x80000000 + 0x01000000 0x00000000 0x00000000 0x0000000f 0x80000000 0x00000000 0x00010000>; + + /* Inbound 2GB range starting at 0 */ + dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x80000000>; + /* This drives busses 10 to 0x1f */ + bus-range = <0x10 0x1f>; + + /* Legacy interrupts (note the weird polarity, the bridge seems + * to invert PCIe legacy interrupts). + * We are de-swizzling here because the numbers are actually for + * port of the root complex virtual P2P bridge. But I want + * to avoid putting a node for it in the tree, so the numbers + * below are basically de-swizzled numbers. + * The real slot is on idsel 0, so the swizzling is 1:1 + */ + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = < + 0x0 0x0 0x0 0x1 &UIC3 0x0 0x4 /* swizzled int A */ + 0x0 0x0 0x0 0x2 &UIC3 0x1 0x4 /* swizzled int B */ + 0x0 0x0 0x0 0x3 &UIC3 0x2 0x4 /* swizzled int C */ + 0x0 0x0 0x0 0x4 &UIC3 0x3 0x4 /* swizzled int D */>; + }; + + PCIE1: pciex@d20000000 { + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "ibm,plb-pciex-460sx", "ibm,plb-pciex"; + primary; + port = <0x1>; /* port number */ + reg = <0x0000000d 0x20000000 0x20000000 /* Config space access */ + 0x0000000c 0x10001000 0x00001000>; /* Registers */ + dcr-reg = <0x120 0x020>; + sdr-base = <0x340>; + + /* Outbound ranges, one memory and one IO, + * later cannot be changed + */ + ranges = <0x02000000 0x00000000 0x80000000 0x0000000e 0x80000000 0x00000000 0x80000000 + 0x01000000 0x00000000 0x00000000 0x0000000f 0x80010000 0x00000000 0x00010000>; + + /* Inbound 2GB range starting at 0 */ + dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x80000000>; + + /* This drives busses 10 to 0x1f */ + bus-range = <0x20 0x2f>; + + /* Legacy interrupts (note the weird polarity, the bridge seems + * to invert PCIe legacy interrupts). + * We are de-swizzling here because the numbers are actually for + * port of the root complex virtual P2P bridge. But I want + * to avoid putting a node for it in the tree, so the numbers + * below are basically de-swizzled numbers. + * The real slot is on idsel 0, so the swizzling is 1:1 + */ + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = < + 0x0 0x0 0x0 0x1 &UIC3 0x4 0x4 /* swizzled int A */ + 0x0 0x0 0x0 0x2 &UIC3 0x5 0x4 /* swizzled int B */ + 0x0 0x0 0x0 0x3 &UIC3 0x6 0x4 /* swizzled int C */ + 0x0 0x0 0x0 0x4 &UIC3 0x7 0x4 /* swizzled int D */>; + }; + + PCIE2: pciex@d40000000 { + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "ibm,plb-pciex-460sx", "ibm,plb-pciex"; + primary; + port = <0x2>; /* port number */ + reg = <0x0000000d 0x40000000 0x20000000 /* Config space access */ + 0x0000000c 0x10002000 0x00001000>; /* Registers */ + dcr-reg = <0x140 0x020>; + sdr-base = <0x370>; + + /* Outbound ranges, one memory and one IO, + * later cannot be changed + */ + ranges = <0x02000000 0x00000000 0x80000000 0x0000000f 0x00000000 0x00000000 0x80000000 + 0x01000000 0x00000000 0x00000000 0x0000000f 0x80020000 0x00000000 0x00010000>; + + /* Inbound 2GB range starting at 0 */ + dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x80000000>; + + /* This drives busses 10 to 0x1f */ + bus-range = <0x30 0x3f>; + + /* Legacy interrupts (note the weird polarity, the bridge seems + * to invert PCIe legacy interrupts). + * We are de-swizzling here because the numbers are actually for + * port of the root complex virtual P2P bridge. But I want + * to avoid putting a node for it in the tree, so the numbers + * below are basically de-swizzled numbers. + * The real slot is on idsel 0, so the swizzling is 1:1 + */ + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = < + 0x0 0x0 0x0 0x1 &UIC3 0x8 0x4 /* swizzled int A */ + 0x0 0x0 0x0 0x2 &UIC3 0x9 0x4 /* swizzled int B */ + 0x0 0x0 0x0 0x3 &UIC3 0xa 0x4 /* swizzled int C */ + 0x0 0x0 0x0 0x4 &UIC3 0xb 0x4 /* swizzled int D */>; }; }; + chosen { linux,stdout-path = "/plb/opb/serial@ef600200"; };
arch/powerpc/sysdev/ppc4xx_pci.c +119 -0
131 lines not on this page · raw message
arch/powerpc/sysdev/ppc4xx_pci.h +58 -0
64 lines not on this page · raw message
Signature · 1 line
1.6.1.rc3
Quoted 4 lines · On Tue, Dec 22, 2009 at 12:49:41AM -0800, [email protected] wrote:
From: Tirumala Marri <[email protected]>
Signed-off-by Tirumala Marri <[email protected]>
Ben, do you want to take this through your tree or mine?
josh
Quoted 361 lines
---
Kerenl:2.6.33-rc1
Testing: This patch has been tested on 460SX based redwood board . One board configured as root complex and other as Endpoint. Checked for link up . From root complex lspci command shows the end point. Also programmed IO tested using loop back as well as board to board.
---arch/powerpc/boot/dts/redwood.dts | 122 +++++++++++++++++++++++++++++++++++++ arch/powerpc/sysdev/ppc4xx_pci.c | 119 ++++++++++++++++++++++++++++++++++++ arch/powerpc/sysdev/ppc4xx_pci.h | 58 +++++++++++++++++ 3 files changed, 299 insertions(+), 0 deletions(-)arch/powerpc/boot/dts/redwood.dts +122
-0@@ -234,10 +234,132 @@ has-inverted-stacr-oc; has-new-stacr-staopc; }; + }; + PCIE0: pciex@d00000000 { + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "ibm,plb-pciex-460sx", "ibm,plb-pciex"; + primary; + port = <0x0>; /* port number */ + reg = <0x0000000d 0x00000000 0x20000000 /* Config space access */ + 0x0000000c 0x10000000 0x00001000>; /* Registers */ + dcr-reg = <0x100 0x020>; + sdr-base = <0x300>; + + /* Outbound ranges, one memory and one IO, + * later cannot be changed + */ + ranges = <0x02000000 0x00000000 0x80000000 0x0000000e 0x00000000 0x00000000 0x80000000 + 0x01000000 0x00000000 0x00000000 0x0000000f 0x80000000 0x00000000 0x00010000>; + + /* Inbound 2GB range starting at 0 */ + dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x80000000>; + /* This drives busses 10 to 0x1f */ + bus-range = <0x10 0x1f>; + + /* Legacy interrupts (note the weird polarity, the bridge seems + * to invert PCIe legacy interrupts). + * We are de-swizzling here because the numbers are actually for + * port of the root complex virtual P2P bridge. But I want + * to avoid putting a node for it in the tree, so the numbers + * below are basically de-swizzled numbers. + * The real slot is on idsel 0, so the swizzling is 1:1 + */ + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = < + 0x0 0x0 0x0 0x1 &UIC3 0x0 0x4 /* swizzled int A */ + 0x0 0x0 0x0 0x2 &UIC3 0x1 0x4 /* swizzled int B */ + 0x0 0x0 0x0 0x3 &UIC3 0x2 0x4 /* swizzled int C */ + 0x0 0x0 0x0 0x4 &UIC3 0x3 0x4 /* swizzled int D */>; + }; + + PCIE1: pciex@d20000000 { + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "ibm,plb-pciex-460sx", "ibm,plb-pciex"; + primary; + port = <0x1>; /* port number */ + reg = <0x0000000d 0x20000000 0x20000000 /* Config space access */ + 0x0000000c 0x10001000 0x00001000>; /* Registers */ + dcr-reg = <0x120 0x020>; + sdr-base = <0x340>; + + /* Outbound ranges, one memory and one IO, + * later cannot be changed + */ + ranges = <0x02000000 0x00000000 0x80000000 0x0000000e 0x80000000 0x00000000 0x80000000 + 0x01000000 0x00000000 0x00000000 0x0000000f 0x80010000 0x00000000 0x00010000>; + + /* Inbound 2GB range starting at 0 */ + dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x80000000>; + + /* This drives busses 10 to 0x1f */ + bus-range = <0x20 0x2f>; + + /* Legacy interrupts (note the weird polarity, the bridge seems + * to invert PCIe legacy interrupts). + * We are de-swizzling here because the numbers are actually for + * port of the root complex virtual P2P bridge. But I want + * to avoid putting a node for it in the tree, so the numbers + * below are basically de-swizzled numbers. + * The real slot is on idsel 0, so the swizzling is 1:1 + */ + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = < + 0x0 0x0 0x0 0x1 &UIC3 0x4 0x4 /* swizzled int A */ + 0x0 0x0 0x0 0x2 &UIC3 0x5 0x4 /* swizzled int B */ + 0x0 0x0 0x0 0x3 &UIC3 0x6 0x4 /* swizzled int C */ + 0x0 0x0 0x0 0x4 &UIC3 0x7 0x4 /* swizzled int D */>; + }; + + PCIE2: pciex@d40000000 { + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "ibm,plb-pciex-460sx", "ibm,plb-pciex"; + primary; + port = <0x2>; /* port number */ + reg = <0x0000000d 0x40000000 0x20000000 /* Config space access */ + 0x0000000c 0x10002000 0x00001000>; /* Registers */ + dcr-reg = <0x140 0x020>; + sdr-base = <0x370>; + + /* Outbound ranges, one memory and one IO, + * later cannot be changed + */ + ranges = <0x02000000 0x00000000 0x80000000 0x0000000f 0x00000000 0x00000000 0x80000000 + 0x01000000 0x00000000 0x00000000 0x0000000f 0x80020000 0x00000000 0x00010000>; + + /* Inbound 2GB range starting at 0 */ + dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x80000000>; + + /* This drives busses 10 to 0x1f */ + bus-range = <0x30 0x3f>; + + /* Legacy interrupts (note the weird polarity, the bridge seems + * to invert PCIe legacy interrupts). + * We are de-swizzling here because the numbers are actually for + * port of the root complex virtual P2P bridge. But I want + * to avoid putting a node for it in the tree, so the numbers + * below are basically de-swizzled numbers. + * The real slot is on idsel 0, so the swizzling is 1:1 + */ + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = < + 0x0 0x0 0x0 0x1 &UIC3 0x8 0x4 /* swizzled int A */ + 0x0 0x0 0x0 0x2 &UIC3 0x9 0x4 /* swizzled int B */ + 0x0 0x0 0x0 0x3 &UIC3 0xa 0x4 /* swizzled int C */ + 0x0 0x0 0x0 0x4 &UIC3 0xb 0x4 /* swizzled int D */>; }; }; + chosen { linux,stdout-path = "/plb/opb/serial@ef600200"; };arch/powerpc/sysdev/ppc4xx_pci.c +119
-0@@ -972,6 +972,123 @@ static struct ppc4xx_pciex_hwops ppc460ex_pcie_hwops __initdata = .setup_utl = ppc460ex_pciex_init_utl, }; +static int __init ppc460sx_pciex_core_init (struct device_node *np) +{ +/* HSS drive amplitude */ +mtdcri (SDR0 ,PESDR0_460SX_HSSL0DAMP ,0xB9843211 ); +mtdcri (SDR0 ,PESDR0_460SX_HSSL1DAMP ,0xB9843211 ); +mtdcri (SDR0 ,PESDR0_460SX_HSSL2DAMP ,0xB9843211 ); +mtdcri (SDR0 ,PESDR0_460SX_HSSL3DAMP ,0xB9843211 ); +mtdcri (SDR0 ,PESDR0_460SX_HSSL4DAMP ,0xB9843211 ); +mtdcri (SDR0 ,PESDR0_460SX_HSSL5DAMP ,0xB9843211 ); +mtdcri (SDR0 ,PESDR0_460SX_HSSL6DAMP ,0xB9843211 ); +mtdcri (SDR0 ,PESDR0_460SX_HSSL7DAMP ,0xB9843211 ); + +mtdcri (SDR0 ,PESDR1_460SX_HSSL0DAMP ,0xB9843211 ); +mtdcri (SDR0 ,PESDR1_460SX_HSSL1DAMP ,0xB9843211 ); +mtdcri (SDR0 ,PESDR1_460SX_HSSL2DAMP ,0xB9843211 ); +mtdcri (SDR0 ,PESDR1_460SX_HSSL3DAMP ,0xB9843211 ); + +mtdcri (SDR0 ,PESDR2_460SX_HSSL0DAMP ,0xB9843211 ); +mtdcri (SDR0 ,PESDR2_460SX_HSSL1DAMP ,0xB9843211 ); +mtdcri (SDR0 ,PESDR2_460SX_HSSL2DAMP ,0xB9843211 ); +mtdcri (SDR0 ,PESDR2_460SX_HSSL3DAMP ,0xB9843211 ); + +/* HSS TX pre-emphasis */ +mtdcri (SDR0 ,PESDR0_460SX_HSSL0COEFA ,0xDCB98987 ); +mtdcri (SDR0 ,PESDR0_460SX_HSSL1COEFA ,0xDCB98987 ); +mtdcri (SDR0 ,PESDR0_460SX_HSSL2COEFA ,0xDCB98987 ); +mtdcri (SDR0 ,PESDR0_460SX_HSSL3COEFA ,0xDCB98987 ); +mtdcri (SDR0 ,PESDR0_460SX_HSSL4COEFA ,0xDCB98987 ); +mtdcri (SDR0 ,PESDR0_460SX_HSSL5COEFA ,0xDCB98987 ); +mtdcri (SDR0 ,PESDR0_460SX_HSSL6COEFA ,0xDCB98987 ); +mtdcri (SDR0 ,PESDR0_460SX_HSSL7COEFA ,0xDCB98987 ); + +mtdcri (SDR0 ,PESDR1_460SX_HSSL0COEFA ,0xDCB98987 ); +mtdcri (SDR0 ,PESDR1_460SX_HSSL1COEFA ,0xDCB98987 ); +mtdcri (SDR0 ,PESDR1_460SX_HSSL2COEFA ,0xDCB98987 ); +mtdcri (SDR0 ,PESDR1_460SX_HSSL3COEFA ,0xDCB98987 ); + +mtdcri (SDR0 ,PESDR2_460SX_HSSL0COEFA ,0xDCB98987 ); +mtdcri (SDR0 ,PESDR2_460SX_HSSL1COEFA ,0xDCB98987 ); +mtdcri (SDR0 ,PESDR2_460SX_HSSL2COEFA ,0xDCB98987 ); +mtdcri (SDR0 ,PESDR2_460SX_HSSL3COEFA ,0xDCB98987 ); + +/* HSS TX calibration control */ +mtdcri (SDR0 ,PESDR0_460SX_HSSL1CALDRV ,0x22222222 ); +mtdcri (SDR0 ,PESDR1_460SX_HSSL1CALDRV ,0x22220000 ); +mtdcri (SDR0 ,PESDR2_460SX_HSSL1CALDRV ,0x22220000 ); + +/* HSS TX slew control */ +mtdcri (SDR0 ,PESDR0_460SX_HSSSLEW ,0xFFFFFFFF ); +mtdcri (SDR0 ,PESDR1_460SX_HSSSLEW ,0xFFFF0000 ); +mtdcri (SDR0 ,PESDR2_460SX_HSSSLEW ,0xFFFF0000 ); + +udelay (100 ); + +/* De-assert PLLRESET */ +dcri_clrset (SDR0 ,PESDR0_PLLLCT2 ,0x00000100 ,0 ); + +/* Reset DL, UTL, GPL before configuration */ +mtdcri (SDR0 ,PESDR0_460SX_RCSSET , + PESDRx_RCSSET_RSTDL | PESDRx_RCSSET_RSTGU); +mtdcri (SDR0 ,PESDR1_460SX_RCSSET , + PESDRx_RCSSET_RSTDL | PESDRx_RCSSET_RSTGU); +mtdcri (SDR0 ,PESDR2_460SX_RCSSET , + PESDRx_RCSSET_RSTDL | PESDRx_RCSSET_RSTGU); + +udelay (100 ); + +/* +* If bifurcation is not enabled, u-boot would have disabled the +* third PCIe port +*/ +if (((mfdcri (SDR0 ,PESDR1_460SX_HSSCTLSET ) &0x00000001 ) == +0x00000001 )) { +printk (KERN_INFO "PCI: PCIE bifurcation setup successfully.\n" ); +printk (KERN_INFO "PCI: Total 3 PCIE ports are present\n" ); +return 3 ; + } + +printk (KERN_INFO "PCI: Total 2 PCIE ports are present\n" ); +return 2 ; +} + +static int ppc460sx_pciex_init_port_hw (struct ppc4xx_pciex_port *port) +{ + +if (port->endpoint) +dcri_clrset (SDR0 , port->sdr_base + PESDRn_UTLSET2, +0x01000000 ,0 ); +else +dcri_clrset (SDR0 , port->sdr_base + PESDRn_UTLSET2, +0 ,0x01000000 ); + +/*Gen-1*/ +mtdcri (SDR0 , port->sdr_base + PESDRn_460SX_RCEI,0x08000000 ); + +dcri_clrset (SDR0 , port->sdr_base + PESDRn_RCSSET, + (PESDRx_RCSSET_RSTGU | PESDRx_RCSSET_RSTDL), + PESDRx_RCSSET_RSTPYN); + + port->has_ibpre =1 ; + +return 0 ; +} + +static int ppc460sx_pciex_init_utl (struct ppc4xx_pciex_port *port) +{ +/* Max 128 Bytes */ +out_be32 (port->utl_base +PEUTL_PBBSZ ,0x00000000 ); +return 0 ; +} + +static struct ppc4xx_pciex_hwops ppc460sx_pcie_hwops__initdata = { + .core_init = ppc460sx_pciex_core_init, + .port_init_hw = ppc460sx_pciex_init_port_hw, + .setup_utl = ppc460sx_pciex_init_utl, +}; +#endif /* CONFIG_44x */ #ifdef CONFIG_40x@@ -1087,6 +1204,8 @@ static int __init ppc4xx_pciex_check_core_init(struct device_node *np) }if (of_device_is_compatible (np,"ibm,plb-pciex-460ex" )) ppc4xx_pciex_hwops = &ppc460ex_pcie_hwops; +if (of_device_is_compatible (np,"ibm,plb-pciex-460sx" )) + ppc4xx_pciex_hwops = &ppc460sx_pcie_hwops;#endif /* CONFIG_44x */ #ifdef CONFIG_40xif (of_device_is_compatible (np,"ibm,plb-pciex-405ex" ))arch/powerpc/sysdev/ppc4xx_pci.h +58
-0@@ -324,6 +324,64 @@#define PESDR0_460EX_IHS2 0x036D/* +* 460SX addtional DCRs +*/ +#define PESDRn_460SX_RCEI 0x02 + +#define PESDR0_460SX_HSSL0DAMP 0x320 +#define PESDR0_460SX_HSSL1DAMP 0x321 +#define PESDR0_460SX_HSSL2DAMP 0x322 +#define PESDR0_460SX_HSSL3DAMP 0x323 +#define PESDR0_460SX_HSSL4DAMP 0x324 +#define PESDR0_460SX_HSSL5DAMP 0x325 +#define PESDR0_460SX_HSSL6DAMP 0x326 +#define PESDR0_460SX_HSSL7DAMP 0x327 + +#define PESDR1_460SX_HSSL0DAMP 0x354 +#define PESDR1_460SX_HSSL1DAMP 0x355 +#define PESDR1_460SX_HSSL2DAMP 0x356 +#define PESDR1_460SX_HSSL3DAMP 0x357 + +#define PESDR2_460SX_HSSL0DAMP 0x384 +#define PESDR2_460SX_HSSL1DAMP 0x385 +#define PESDR2_460SX_HSSL2DAMP 0x386 +#define PESDR2_460SX_HSSL3DAMP 0x387 + +#define PESDR0_460SX_HSSL0COEFA 0x328 +#define PESDR0_460SX_HSSL1COEFA 0x329 +#define PESDR0_460SX_HSSL2COEFA 0x32A +#define PESDR0_460SX_HSSL3COEFA 0x32B +#define PESDR0_460SX_HSSL4COEFA 0x32C +#define PESDR0_460SX_HSSL5COEFA 0x32D +#define PESDR0_460SX_HSSL6COEFA 0x32E +#define PESDR0_460SX_HSSL7COEFA 0x32F + +#define PESDR1_460SX_HSSL0COEFA 0x358 +#define PESDR1_460SX_HSSL1COEFA 0x359 +#define PESDR1_460SX_HSSL2COEFA 0x35A +#define PESDR1_460SX_HSSL3COEFA 0x35B + +#define PESDR2_460SX_HSSL0COEFA 0x388 +#define PESDR2_460SX_HSSL1COEFA 0x389 +#define PESDR2_460SX_HSSL2COEFA 0x38A +#define PESDR2_460SX_HSSL3COEFA 0x38B + +#define PESDR0_460SX_HSSL1CALDRV 0x339 +#define PESDR1_460SX_HSSL1CALDRV 0x361 +#define PESDR2_460SX_HSSL1CALDRV 0x391 + +#define PESDR0_460SX_HSSSLEW 0x338 +#define PESDR1_460SX_HSSSLEW 0x360 +#define PESDR2_460SX_HSSSLEW 0x390 + +#define PESDR0_460SX_HSSCTLSET 0x31E +#define PESDR1_460SX_HSSCTLSET 0x352 +#define PESDR2_460SX_HSSCTLSET 0x382 + +#define PESDR0_460SX_RCSSET 0x304 +#define PESDR1_460SX_RCSSET 0x344 +#define PESDR2_460SX_RCSSET 0x374 +/* * Of the above, some are common offsets from the base */ #define PESDRn_UTLSET1 0x00Signature · 6 lines
1.6.1.rc3 _______________________________________________ Linuxppc-dev mailing list [email protected] https://lists.ozlabs.org/listinfo/linuxppc-dev