Skip to contentSkip to conversation

Removing a PV from a mirror

linux-lvm Fredrik Tolf 3 participants 6 messages Jan 11, 2010 – Feb 12, 2010

lore
Share & tools
lore
#0 lore raw

Hi list,

I've got a mirror volume with two S-ATA disks, one of which started getting bad sectors recently, and I want to replace it. I'm having trouble removing it from the volume, however.

When googling around on the subject, I've read everywhere that I shouldn't have to do anymore than remove it, and LVM should discover that and reconvert the mirror back into a linear volume. To be a bit more careful, though, I ran "echo 1 >/sys/block/sdh/device/delete" to have it removed properly in software first. Much to my surprise, shall we say, that just made the LV die a horrible death; it started returning EIO for every access to it, and I had to reboot the server to get it working again. Again, this is the proper procedure according to what I've been reading on the net; did I do it wrong, somehow, or are my sources completely off? (And if this doesn't work, then what would actually happen if the disk were to fail physically?)

As I rebooted the server, I tried disconnecting the disk in advance, but that made LVM unable to bring the VG back online at all.

How am I supposed to take this disk out of the volume? If I should use `lvconvert -m 0 $LV', then how do I specify which disk is to be removed?

I'm using a stock Debian stable (Lenny) installation, meaning Linux 2.6.24 and LVM2 2.02.39.

Appreciative for any answers,

Fredrik Tolf

#1 lore raw

oh... sorry to hear.
Actually, Fredrick, you may just answered my question that i posted earlier about moving VG to another disk(s) and changing the stiping to linear. I think (hope) that the command i needed is : lvconvert -m 0 ....

i hope you did take a backup ?
Andrew

Quoted 38 lines · Fredrik Tolf

Hi list,

I've got a mirror volume with two S-ATA disks, one of which started getting bad sectors recently, and I want to replace it. I'm having trouble removing it from the volume, however.

When googling around on the subject, I've read everywhere that I shouldn't have to do anymore than remove it, and LVM should discover that and reconvert the mirror back into a linear volume. To be a bit more careful, though, I ran "echo 1 >/sys/block/sdh/device/delete" to have it removed properly in software first. Much to my surprise, shall we say, that just made the LV die a horrible death; it started returning EIO for every access to it, and I had to reboot the server to get it working again. Again, this is the proper procedure according to what I've been reading on the net; did I do it wrong, somehow, or are my sources completely off? (And if this doesn't work, then what would actually happen if the disk were to fail physically?)

As I rebooted the server, I tried disconnecting the disk in advance, but that made LVM unable to bring the VG back online at all.

How am I supposed to take this disk out of the volume? If I should use `lvconvert -m 0 $LV', then how do I specify which disk is to be removed?

I'm using a stock Debian stable (Lenny) installation, meaning Linux 2.6.24 and LVM2 2.02.39.

Appreciative for any answers,

Fredrik Tolf

_______________________________________________
linux-lvm mailing list
[email protected]
https://www.redhat.com/mailman/listinfo/linux-lvm
read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/

#2 lore raw
Quoted 1 line · Misc Things

oh... sorry to hear.

[...]

Quoted 2 lines

i hope you did take a backup ?
Andrew

Oh, sorry; when I go back and read it, I realize that I was a bit unclear. :) The LV started working again once I reconnected the PV and rebooted again, so there's no damage done.

I'm still just wondering how to actually remove the PV from the mirror.

Fredrik Tolf

#3 lore raw

Fredrik, I haven't done this personally, but did remove the pv from stripped VG. All that was required - i followed the tutorial.
Sorry can't be of more help.

Andrew

Quoted 21 lines · Fredrik Tolf
Quoted 1 line · Misc Things

oh... sorry to hear.

[...]

Quoted 2 lines

i hope you did take a backup ?
Andrew

Oh, sorry; when I go back and read it, I realize that I was a bit unclear. :) The LV started working again once I reconnected the PV and rebooted again, so there's no damage done.

I'm still just wondering how to actually remove the PV from the mirror.

Fredrik Tolf

_______________________________________________
linux-lvm mailing list
[email protected]
https://www.redhat.com/mailman/listinfo/linux-lvm
read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/

#4 lore raw
In reply to Fredrik Tolf
Quoted 5 lines · Fredrik Tolf [[email protected]] wrote:

Oh, sorry; when I go back and read it, I realize that I was a bit unclear. :) The LV started working again once I reconnected the PV and rebooted again, so there's no damage done.

I'm still just wondering how to actually remove the PV from the mirror.

Since your PV is flakey (failing), probably the best way is to convert the LV to linear first and then converting back to mirror with a new PV.

A failing PV should make the system convert to linear LV if you have right software (works on RHEL based system). Or you can do the following steps manually. First step may not be necessary, but it should not cause any harm in your case.

0) Run vgcfgbackup to back up your LVM metadata. This is needed if something goes wrong. You have been warned. If you know, this data is already there in archives...
1) lvconvert --mirrorlog core <LV-name>
2) lvconvert -m0 <LV-name> <Failing-PV-name>
Make sure this did remove the PV you wanted. If not, use vgcfgrestore to restore and ask for help...
3) Insert your new disk, create PV label on it, and add it to your VG
4) Run "lvconvert -m1 <LV-name> <New-PV-name>
5) If you need "disk" log, run another lvconvert to get disk log.

Hope this helps,
--Malahal.

#5 lore raw
Quoted 6 lines · On Tue, 2010-01-12 at 11:16 -0800, [email protected] wrote:
Quoted 1 line · Fredrik Tolf [[email protected]] wrote:

I'm still just wondering how to actually remove the PV from the mirror.

2) lvconvert -m0 <LV-name> <Failing-PV-name>
Make sure this did remove the PV you wanted. If not, use vgcfgrestore to restore and ask for help...

Ah, so that's how you do it! Thanks a lot!

Fredrik Tolf