Skip to contentSkip to conversation

drm/panel: Add support for Samsung LTN101NT05 panel

PATCH In review Marc Dietrich 4 participants 13 messages Dec 21, 2013 – Feb 5, 2014

Subsystems (6)
lore
Share & tools
lore
#0 lore raw

PATCH 1/2 drm/panel: Add support for Samsung LTN101NT05 panel

The Samsung LNT101NT05 10.1" WXVGA panel can be supported by the simple panel driver.

---
This isn't strickly required to get the panel up, but Thierry suggested on IRC to include it anyway, in case someone else has some use for it.

 .../bindings/panel/samsung,ltn101nt05.txt          |    7 +++++
 drivers/gpu/drm/panel/panel-simple.c               |   27 +++++++++++++++++++-
 2 files changed, 33 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/panel/samsung,ltn101nt05.txt
Documentation/devicetree/bindings/panel/samsung,ltn101nt05.txt new file +7 -0
new file mode 100644
index 0000000..ef522c6
@@ -0,0 +1,7 @@
+Samsung Electronics 10.1" WSVGA TFT LCD panel
+
+Required properties:
+- compatible: should be "samsung,ltn101nt05"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
drivers/gpu/drm/panel/panel-simple.c +25 -0
index 3e611af..7f9ddb5 100644
@@ -338,6 +338,28 @@ static const struct panel_desc chunghwa_claa101wb01 = {
 	},
 };
 
+static const struct drm_display_mode samsung_ltn101nt05_mode = {
+	.clock = 54030,
+	.hdisplay = 1024,
+	.hsync_start = 1024 + 24,
+	.hsync_end = 1024 + 24 + 136,
+	.htotal = 1024 + 24 + 136 + 160,
+	.vdisplay = 600,
+	.vsync_start = 600 + 3,
+	.vsync_end = 600 + 3 + 6,
+	.vtotal = 600 + 3 + 6 + 61,
+	.vrefresh = 60,
+};
+
+static const struct panel_desc samsung_ltn101nt05 = {
+	.modes = &samsung_ltn101nt05_mode,
+	.num_modes = 1,
+	.size = {
+		.width = 1024,
+		.height = 600,
+	},
+};
+
 static const struct of_device_id platform_of_match[] = {
 	{
 		.compatible = "auo,b101aw03",
@@ -346,6 +368,9 @@ static const struct of_device_id platform_of_match[] = {
 		.compatible = "chunghwa,claa101wb01",
 		.data = &chunghwa_claa101wb01
 	}, {
+		.compatible = "samsung,ltn101nt05",
+		.data = &samsung_ltn101nt05,
+	}, {
 		.compatible = "simple-panel",
 	}, {
 		/* sentinel */
Signature · 1 line
1.7.9.5
#1 lore raw

PATCH 2/2 ARM: tegra: paz00: Add LVDS support to device tree

Add backlight and panel nodes for the PAZ00 TFT LCD panel.

---
This should enable everything needed. Unfortunately, in my tests it only switches on the backlight, but the display controller blocks in some infinit loop, so we get no output (and no working system). I post it here in case I missed something obvious...

 arch/arm/boot/dts/tegra20-paz00.dts |   46 ++++++++++++++++++++++++++++++++++-
 1 file changed, 45 insertions(+), 1 deletion(-)
arch/arm/boot/dts/tegra20-paz00.dts +45 -1
index c7cd8e6..9a39a80 100644
@@ -17,6 +17,14 @@
 	};
 
 	host1x at 50000000 {
+		dc at 54200000 {
+			rgb {
+				status = "okay";
+
+				nvidia,panel = <&panel>;
+			};
+		};
+
 		hdmi at 54280000 {
 			status = "okay";
 
@@ -257,7 +265,11 @@
 		status = "okay";
 	};
 
-	i2c at 7000c000 {
+	pwm: pwm at 7000a000 {
+		status = "okay";
+	};
+
+	lvds_ddc: i2c at 7000c000 {
 		status = "okay";
 		clock-frequency = <400000>;
 
@@ -475,6 +487,18 @@
 		non-removable;
 	};
 
+	backlight: backlight {
+		compatible = "pwm-backlight";
+
+		enable-gpios = <&gpio TEGRA_GPIO(U, 4) GPIO_ACTIVE_HIGH>;
+		pwms = <&pwm 0 5000000>;
+
+		brightness-levels = <0 16 32 48 64 80 96 112 128 144 160 176 192 208 224 240 255>;
+		default-brightness-level = <10>;
+
+		backlight-boot-off;
+	};
+
 	clocks {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -509,6 +533,16 @@
 		};
 	};
 
+	panel: panel {
+		compatible = "samsung,ltn101nt05", "simple-panel";
+
+		ddc-i2c-bus = <&lvds_ddc>;
+		power-supply = <&vdd_pnl_reg>;
+		enable-gpios = <&gpio TEGRA_GPIO(M, 6) GPIO_ACTIVE_HIGH>;
+
+		backlight = <&backlight>;
+	};
+
 	regulators {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -522,6 +556,16 @@
 			regulator-max-microvolt = <5000000>;
 			regulator-always-on;
 		};
+
+		vdd_pnl_reg: regulator at 1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "+3VS,vdd_pnl";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio TEGRA_GPIO(A, 4) GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
 	};
 
 	sound {
Signature · 1 line
1.7.9.5
#2 lore raw

PATCH 2/2 ARM: tegra: paz00: Add LVDS support to device tree

Sorry, Stephen, I mistyped your email address in the first post.

Quoted 8 lines · On Saturday 21 December 2013 21:38:13 Marc Dietrich wrote:

Add backlight and panel nodes for the PAZ00 TFT LCD panel.

---
This should enable everything needed. Unfortunately, in my tests it only switches on the backlight, but the display controller blocks in some infinit loop, so we get no output (and no working system). I post it here in case I missed something obvious...

In fact it turns out to be some heisenbug because in one out of ten tries it actually works. The other nine cases it prints:

[    1.995067] rfkill_gpio rfkill_gpio: wifi_rfkill device registered.
[    2.001459] Registering SWP/SWPB emulation handler
[    2.011632] [drm:drm_get_minor], 
[    2.016473] [drm:drm_get_minor], new minor assigned 64
[    2.021648] [drm:drm_get_minor], 
[    2.026319] [drm:drm_get_minor], new minor assigned 0
[    2.033465] [drm:drm_sysfs_connector_add], adding "HDMI-A-1" to sysfs
[    2.040402] [drm:drm_sysfs_hotplug_event], generating hotplug event
[    2.048115] [drm:drm_sysfs_connector_add], adding "LVDS-1" to sysfs
[    2.054642] [drm:drm_sysfs_hotplug_event], generating hotplug event
[    2.061341] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    2.068027] [drm] No driver support for vblank timestamp query.
[    2.094947] random: nonblocking pool is initialized
[  240.885976] INFO: task swapper/0:1 blocked for more than 120 seconds.
[  240.892462]       Not tainted 3.13.0-rc4-next-20131220-00003-gbcf12ec #11
[  240.900030] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables 
this message.
[  240.907997] swapper/0       D c05653b8     0     1      0 0x00000000
[  240.914457] [<c05653b8>] (__schedule) from [<c0564bcc>] 
(schedule_timeout+0x174/0x1ec)
[  240.922512] [<c0564bcc>] (schedule_timeout) from [<c056603c>] 
(wait_for_common+0xb0/0x144)
[  240.930913] [<c056603c>] (wait_for_common) from [<c0038db8>] 
(flush_workqueue+0xec/0x570)
[  240.939227] [<c0038db8>] (flush_workqueue) from [<c02b7048>] 
(deferred_probe_initcall+0x50/0x80)
[  240.948143] [<c02b7048>] (deferred_probe_initcall) from [<c00089f4>] 
(do_one_initcall+0xe4/0x140)
[  240.957179] [<c00089f4>] (do_one_initcall) from [<c0784be8>] 
(kernel_init_freeable+0xfc/0x1c8)
[  240.965936] [<c0784be8>] (kernel_init_freeable) from [<c055eb94>] 
(kernel_init+0x8/0x118)
[  240.974180] [<c055eb94>] (kernel_init) from [<c000e678>] 
(ret_from_fork+0x14/0x3c)
[  261.904891] INFO: rcu_preempt self-detected stall on CPU { 0}  (t=2100 
jiffies g=4294967023 c=4294967022 q=1)
[  261.914827] CPU: 0 PID: 55 Comm: kworker/u4:2 Not tainted 3.13.0-rc4-
next-20131220-00003-gbcf12ec #11
[  261.924042] Workqueue: deferwq deferred_probe_work_func
[  261.929285] [<c0015b2c>] (unwind_backtrace) from [<c00117e0>] 
(show_stack+0x10/0x14)
[  261.937036] [<c00117e0>] (show_stack) from [<c0563180>] 
(dump_stack+0x80/0xcc)
[  261.944261] [<c0563180>] (dump_stack) from [<c006ce00>] 
(rcu_check_callbacks+0x408/0x850)
[  261.952442] [<c006ce00>] (rcu_check_callbacks) from [<c002fbe0>] 
(update_process_times+0x38/0x58)
[  261.961312] [<c002fbe0>] (update_process_times) from [<c0076894>] 
(tick_sched_timer+0x44/0x74)
[  261.969929] [<c0076894>] (tick_sched_timer) from [<c00422a4>] 
(__run_hrtimer.isra.15+0x58/0x114)
[  261.978711] [<c00422a4>] (__run_hrtimer.isra.15) from [<c0042bd0>] 
(hrtimer_interrupt+0xfc/0x288)
[  261.987579] [<c0042bd0>] (hrtimer_interrupt) from [<c001509c>] 
(twd_handler+0x2c/0x40)
[  261.995500] [<c001509c>] (twd_handler) from [<c006719c>] 
(handle_percpu_devid_irq+0x68/0x84)
[  262.003935] [<c006719c>] (handle_percpu_devid_irq) from [<c0063b14>] 
(generic_handle_irq+0x20/0x30)
[  262.012977] [<c0063b14>] (generic_handle_irq) from [<c000ee94>] 
(handle_IRQ+0x38/0x94)
[  262.020890] [<c000ee94>] (handle_IRQ) from [<c0008698>] 
(gic_handle_irq+0x28/0x5c)
[  262.028456] [<c0008698>] (gic_handle_irq) from [<c0012300>] 
(__irq_svc+0x40/0x70)
[  262.035931] Exception stack(0xdb29bc98 to 0xdb29bce0)
[  262.040974] bc80:                                                       
c0814780 00000000
[  262.049145] bca0: ffff8ba1 00000000 00000002 0000001d 00000000 db29a000 
00000002 c07c6080
[  262.057316] bcc0: 00000000 db860000 00000000 db29bce0 c0029898 c0029914 
20000113 ffffffff
[  262.065500] [<c0012300>] (__irq_svc) from [<c0029914>] 
(__do_softirq+0x8c/0x208)
[  262.072895] [<c0029914>] (__do_softirq) from [<c0029dd0>] 
(irq_exit+0xa0/0xec)
[  262.080115] [<c0029dd0>] (irq_exit) from [<c000ee98>] 
(handle_IRQ+0x3c/0x94)
[  262.087158] [<c000ee98>] (handle_IRQ) from [<c0008698>] 
(gic_handle_irq+0x28/0x5c)
[  262.094723] [<c0008698>] (gic_handle_irq) from [<c0012300>] 
(__irq_svc+0x40/0x70)
[  262.102197] Exception stack(0xdb29bd50 to 0xdb29bd98)
[  262.107243] bd40:                                     c0814114 a0000113 
00000000 e0a00000
[  262.115413] bd60: db2f9410 c07cc3d0 00000020 db2f9810 00000002 00000000 
00000000 db860000
[  262.123582] bd80: 00000000 db29bd98 c02a3b6c c02a3b84 60000113 ffffffff
[  262.130198] [<c0012300>] (__irq_svc) from [<c02a3b84>] 
(tegra_output_rgb_disable+0x58/0xe0)
[  262.138548] [<c02a3b84>] (tegra_output_rgb_disable) from [<c02a360c>] 
(tegra_encoder_dpms+0x68/0xc0)
[  262.147675] [<c02a360c>] (tegra_encoder_dpms) from [<c02808ac>] 
(drm_encoder_disable+0x64/0x68)
[  262.156370] [<c02808ac>] (drm_encoder_disable) from [<c02809b8>] 
(drm_helper_disable_unused_functions+0x108/0x134)
[  262.166713] [<c02809b8>] (drm_helper_disable_unused_functions) from 
[<c029f5dc>] (tegra_drm_fb_init+0x88/0x110)
[  262.176794] [<c029f5dc>] (tegra_drm_fb_init) from [<c029e32c>] 
(tegra_drm_load+0x94/0xc0)
[  262.184977] [<c029e32c>] (tegra_drm_load) from [<c028c904>] 
(drm_dev_register+0x70/0x130)
[  262.193151] [<c028c904>] (drm_dev_register) from [<c029df14>] 
(drm_host1x_init+0x2c/0x88)
[  262.201328] [<c029df14>] (drm_host1x_init) from [<c02ab7b0>] 
(host1x_subdev_register+0xb4/0xd0)
[  262.210024] [<c02ab7b0>] (host1x_subdev_register) from [<c02abf00>] 
(host1x_client_register+0xf4/0x11c)
[  262.219412] [<c02abf00>] (host1x_client_register) from [<c02a21ec>] 
(tegra_dc_probe+0x118/0x1ec)
[  262.228196] [<c02a21ec>] (tegra_dc_probe) from [<c02b86d4>] 
(platform_drv_probe+0x18/0x48)
[  262.236457] [<c02b86d4>] (platform_drv_probe) from [<c02b7334>] 
(driver_probe_device+0x118/0x234)
[  262.245334] [<c02b7334>] (driver_probe_device) from [<c02b5a6c>] 
(bus_for_each_drv+0x44/0x8c)
[  262.253855] [<c02b5a6c>] (bus_for_each_drv) from [<c02b71e4>] 
(device_attach+0x70/0x88)
[  262.261854] [<c02b71e4>] (device_attach) from [<c02b68ec>] 
(bus_probe_device+0x84/0xa8)
[  262.269853] [<c02b68ec>] (bus_probe_device) from [<c02b6cdc>] 
(deferred_probe_work_func+0x60/0x8c)
[  262.278808] [<c02b6cdc>] (deferred_probe_work_func) from [<c0039da4>] 
(process_one_work+0xfc/0x350)
[  262.287850] [<c0039da4>] (process_one_work) from [<c003a3fc>] 
(worker_thread+0x13c/0x384)
[  262.296022] [<c003a3fc>] (worker_thread) from [<c003facc>] 
(kthread+0xc4/0xe0)
[  262.303242] [<c003facc>] (kthread) from [<c000e678>] 

(ret_from_fork+0x14/0x3c)

Marc

Quoted 38 lines
 arch/arm/boot/dts/tegra20-paz00.dts |   46

++++++++++++++++++++++++++++++++++- 1 file changed, 45 insertions(+), 1 deletion(-)

(quoted diff) +0 -0

b/arch/arm/boot/dts/tegra20-paz00.dts index c7cd8e6..9a39a80 100644

arch/arm/boot/dts/tegra20-paz00.dts +13 -1
@@ -17,6 +17,14 @@
 	};
 
 	host1x at 50000000 {
+		dc at 54200000 {
+			rgb {
+				status = "okay";
+
+				nvidia,panel = <&panel>;
+			};
+		};
+
 		hdmi at 54280000 {
 			status = "okay";
 
@@ -257,7 +265,11 @@
 		status = "okay";
 	};
 
-	i2c at 7000c000 {
+	pwm: pwm at 7000a000 {
+		status = "okay";
+	};
+
+	lvds_ddc: i2c at 7000c000 {
 		status = "okay";
 		clock-frequency = <400000>;
 

arch/arm/boot/dts/tegra20-paz00.dts line 496

Quoted 10 lines
arch/arm/boot/dts/tegra20-paz00.dts +7 -0
@@ -475,6 +487,18 @@
 		non-removable;
 	};
 
+	backlight: backlight {
+		compatible = "pwm-backlight";
+
+		enable-gpios = <&gpio TEGRA_GPIO(U, 4) GPIO_ACTIVE_HIGH>;
+		pwms = <&pwm 0 5000000>;
+
+		brightness-levels = <0 16 32 48 64 80 96 112 128 144 160 176 192 208 

224

Quoted 42 lines
arch/arm/boot/dts/tegra20-paz00.dts +24 -0
 240 255>; +		default-brightness-level = <10>;
+
+		backlight-boot-off;
+	};
+
 	clocks {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -509,6 +533,16 @@
 		};
 	};
 
+	panel: panel {
+		compatible = "samsung,ltn101nt05", "simple-panel";
+
+		ddc-i2c-bus = <&lvds_ddc>;
+		power-supply = <&vdd_pnl_reg>;
+		enable-gpios = <&gpio TEGRA_GPIO(M, 6) GPIO_ACTIVE_HIGH>;
+
+		backlight = <&backlight>;
+	};
+
 	regulators {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -522,6 +556,16 @@
 			regulator-max-microvolt = <5000000>;
 			regulator-always-on;
 		};
+
+		vdd_pnl_reg: regulator at 1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "+3VS,vdd_pnl";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio TEGRA_GPIO(A, 4) GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
 	};
 
 	sound {
#3 lore raw

PATCH 2/2 ARM: tegra: paz00: Add LVDS support to device tree

Quoted 11 lines · On Saturday 21 December 2013 23:11:58 Marc Dietrich wrote:

Sorry, Stephen, I mistyped your email address in the first post.

Quoted 8 lines · On Saturday 21 December 2013 21:38:13 Marc Dietrich wrote:

Add backlight and panel nodes for the PAZ00 TFT LCD panel.

---
This should enable everything needed. Unfortunately, in my tests it only switches on the backlight, but the display controller blocks in some infinit loop, so we get no output (and no working system). I post it here in case I missed something obvious...

Some users reported that it works when using uboot (yeah, shame on me that I still use fastboot on my dev machine), so I did a bit more research. It indeed works when using uboot, even when the display setup is disabled there. So my guess is that maybe some clock isn't setup by fastboot which is done by uboot.

Marc

#4 lore raw

PATCH 2/2 ARM: tegra: paz00: Add LVDS support to device tree

Quoted 14 lines · On Thursday 26 December 2013 14:52:10 Marc Dietrich wrote:
Quoted 12 lines · On Saturday 21 December 2013 23:11:58 Marc Dietrich wrote:

Sorry, Stephen, I mistyped your email address in the first post.

Quoted 9 lines · On Saturday 21 December 2013 21:38:13 Marc Dietrich wrote:

Add backlight and panel nodes for the PAZ00 TFT LCD panel.

---
This should enable everything needed. Unfortunately, in my tests it only switches on the backlight, but the display controller blocks in some infinit loop, so we get no output (and no working system). I post it here
in case I missed something obvious...

Quoted 5 lines

Some users reported that it works when using uboot (yeah, shame on me that I still use fastboot on my dev machine), so I did a bit more research. It indeed works when using uboot, even when the display setup is disabled there. So my guess is that maybe some clock isn't setup by fastboot which is done by uboot.

ok, to bring this self-conversation to an end, the cpu blocks at a memory barrier right after

	value = tegra_dc_readl(rgb->dc, DC_CMD_DISPLAY_COMMAND);

in tegra_output_rgb_disable (rgb.c).

#5 lore raw

PATCH 2/2 ARM: tegra: paz00: Add LVDS support to device tree

In reply to Marc Dietrich
Quoted 7 lines · Marc Dietrich

Add backlight and panel nodes for the PAZ00 TFT LCD panel.

---
This should enable everything needed. Unfortunately, in my tests it only switches on the backlight, but the display controller blocks in some infinit loop, so we get no output (and no working system). I post it here in case I missed something obvious...

As mentioned later on, this works fine with U-Boot (and tests fine here too), so I plan to apply this for 3.15, once I can.

#6 lore raw

PATCH 2/2 ARM: tegra: paz00: Add LVDS support to device tree

Am Montag, 6. Januar 2014, 12:38:20 schrieb Stephen Warren:

Quoted 11 lines · Marc Dietrich
Quoted 8 lines

Add backlight and panel nodes for the PAZ00 TFT LCD panel.

---
This should enable everything needed. Unfortunately, in my tests it only switches on the backlight, but the display controller blocks in some infinit loop, so we get no output (and no working system). I post it here in case I missed something obvious...

As mentioned later on, this works fine with U-Boot (and tests fine here too), so I plan to apply this for 3.15, once I can.

huh? I thought this can go into 3.14 if possible. Patch is harmless and the merge window still weeks away.

#7 lore raw

PATCH 2/2 ARM: tegra: paz00: Add LVDS support to device tree

Quoted 10 lines · Marc Dietrich

Am Montag, 6. Januar 2014, 12:38:20 schrieb Stephen Warren:

Quoted 9 lines · Marc Dietrich
Quoted 8 lines

Add backlight and panel nodes for the PAZ00 TFT LCD panel.

---
This should enable everything needed. Unfortunately, in my tests it only switches on the backlight, but the display controller blocks in some infinit loop, so we get no output (and no working system). I post it here in case I missed something obvious...

Quoted 5 lines
Quoted 2 lines

As mentioned later on, this works fine with U-Boot (and tests fine here too), so I plan to apply this for 3.15, once I can.

huh? I thought this can go into 3.14 if possible. Patch is harmless and the merge window still weeks away.

The cut-off for new features was at least a week ago. I expect the merge window will open this weekend.

#8 lore raw

PATCH 2/2 ARM: tegra: paz00: Add LVDS support to device tree

Am Montag, 6. Januar 2014, 15:34:01 schrieb Stephen Warren:

Quoted 16 lines · Marc Dietrich
Quoted 15 lines

Am Montag, 6. Januar 2014, 12:38:20 schrieb Stephen Warren:

Quoted 13 lines · Marc Dietrich
Quoted 9 lines

Add backlight and panel nodes for the PAZ00 TFT LCD panel.

---
This should enable everything needed. Unfortunately, in my tests it only switches on the backlight, but the display controller blocks in some infinit loop, so we get no output (and no working system). I post it here
in case I missed something obvious...

As mentioned later on, this works fine with U-Boot (and tests fine here too), so I plan to apply this for 3.15, once I can.

Quoted 6 lines
Quoted 3 lines

huh? I thought this can go into 3.14 if possible. Patch is harmless and the
merge window still weeks away.

The cut-off for new features was at least a week ago. I expect the merge window will open this weekend.

AFAIK, there will be an rc8 (and maybe also an rc9 due to the xmas vacations). I submitted the patchset two days after the LVDS support for the other boards was sent. Ok, there needs to be some deadline and I may have missed it, but it would be really unfortune to miss 3.14 because that's the last missing piece.

#9 lore raw

PATCH 2/2 ARM: tegra: paz00: Add LVDS support to device tree

In reply to Marc Dietrich
Quoted 1 line · Marc Dietrich

Add backlight and panel nodes for the PAZ00 TFT LCD panel.

Applied to Tegra's for-3.15/dt branch.

#10 lore raw
In reply to Marc Dietrich
Quoted 2 lines · Marc Dietrich

The Samsung LNT101NT05 10.1" WXVGA panel can be supported by the simple panel driver.

Thierry, I assume you'll take patch 1/2 throught the appropriate DRM tree.

#11 lore raw
Quoted 5 lines · Stephen Warren
Quoted 2 lines · Marc Dietrich

The Samsung LNT101NT05 10.1" WXVGA panel can be supported by the simple panel driver.

Thierry, I assume you'll take patch 1/2 throught the appropriate DRM tree.

Yes, will do.

Thierry

#12 lore raw
In reply to Marc Dietrich
Quoted 10 lines · Marc Dietrich

The Samsung LNT101NT05 10.1" WXVGA panel can be supported by the simple panel driver.

Cc linux-fbdev at vger.kernel.org
Cc dri-devel at lists.freedesktop.org
Cc David Airlie <[email protected]>

---
This isn't strickly required to get the panel up, but Thierry suggested on IRC to include it anyway, in case someone else has some use for it.

For the record: the reason this isn't strictly needed is because there's an EDID that can be probed to get the video timings. But the panel still can be supported using the timings from the datasheet. One example where this would be useful is when the EDID isn't connected or simply broken.

That said: applied, thanks!

Thierry
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140108/20c2e49f/attachment-0001.sig>