Skip to contentSkip to conversation

RFC patch set - kirkwood/sheeva - enable eSATA port

PATCH New John Holland 2 participants 5 messages Feb 19, 2010

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

Hi there,

included are two patches. The first enables Kconfig and basic board support for the eSATA version of the SheevaPlug found at
http://www.newit.co.uk/store/index.php?main_page=index&cPath=3. No, I have no affiliation. The second enables the SATA interfaces on the SoC to allow eSATA visibility.

I'm opening a discussion to help us decide if the first patch is necessary. Please keep in mind, I also have a third non-disclosed patch that enables SD WP/CD on the same hardware: I have seen that the SoC MPP is also connected to the SD card interface.

http://plugcomputer.org/data/docs/Sheeva-PowerPlug-V1.3-GTI-090906.pdf

Please pardon my git ignorance, but I couldn't find any guidelines forcing me to use it here.

arch/arm/mach-kirkwood/Kconfig +6 -0
diff -Naur linux-2.6-2.6.32/arch/arm/mach-kirkwood/Kconfig linux-2.6-2.6.32.new/arch/arm/mach-kirkwood/Kconfig
@@ -32,6 +32,12 @@
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell SheevaPlug Reference Board.
 
+config MACH_ESATA_SHEEVAPLUG
+	bool "Marvell eSATA SheevaPlug Reference Board"
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  Marvell eSATA SheevaPlug Reference Board.
+
 config MACH_TS219
 	bool "QNAP TS-119 and TS-219 Turbo NAS"
 	help
arch/arm/mach-kirkwood/Makefile +1 -0
diff -Naur linux-2.6-2.6.32/arch/arm/mach-kirkwood/Makefile linux-2.6-2.6.32.new/arch/arm/mach-kirkwood/Makefile
@@ -5,6 +5,7 @@
 obj-$(CONFIG_MACH_RD88F6281)		+= rd88f6281-setup.o
 obj-$(CONFIG_MACH_MV88F6281GTW_GE)	+= mv88f6281gtw_ge-setup.o
 obj-$(CONFIG_MACH_SHEEVAPLUG)		+= sheevaplug-setup.o
+obj-$(CONFIG_MACH_ESATA_SHEEVAPLUG)	+= sheevaplug-setup.o
 obj-$(CONFIG_MACH_TS219)		+= ts219-setup.o
 obj-$(CONFIG_MACH_OPENRD_BASE)		+= openrd_base-setup.o
 
arch/arm/mach-kirkwood/sheevaplug-setup.c +14 -0
diff -Naur linux-2.6-2.6.32/arch/arm/mach-kirkwood/sheevaplug-setup.c linux-2.6-2.6.32.new/arch/arm/mach-kirkwood/sheevaplug-setup.c
@@ -96,6 +96,7 @@
 	platform_device_register(&sheevaplug_leds);
 }
 
+#ifdef CONFIG_MACH_SHEEVAPLUG
 MACHINE_START(SHEEVAPLUG, "Marvell SheevaPlug Reference Board")
 	/* Maintainer: shadi Ammouri <[email protected]> */
 	.phys_io	= KIRKWOOD_REGS_PHYS_BASE,
@@ -106,3 +107,16 @@
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END
+#endif
+
+#ifdef CONFIG_MACH_ESATA_SHEEVAPLUG
+MACHINE_START(ESATA_SHEEVAPLUG, "Marvell eSATA SheevaPlug Reference Board")
+	.phys_io	= KIRKWOOD_REGS_PHYS_BASE,
+	.io_pg_offst	= ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc,
+	.boot_params	= 0x00000100,
+	.init_machine	= sheevaplug_init,
+	.map_io		= kirkwood_map_io,
+	.init_irq	= kirkwood_init_irq,
+	.timer		= &kirkwood_timer,
+MACHINE_END
+#endif

This to allows people to choose the hardware they want to configure in u-boot, depending on the application: using the hardware for something intolerant of "wasted" energy. And leads to the following...

arch/arm/mach-kirkwood/sheevaplug-setup.c +10 -0
diff -Naur linux-2.6-2.6.32/arch/arm/mach-kirkwood/sheevaplug-setup.c linux-2.6-2.6.32.new/arch/arm/mach-kirkwood/sheevaplug-setup.c
@@ -11,6 +11,7 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
+#include <linux/ata_platform.h>
 #include <linux/mtd/partitions.h>
 #include <linux/mv643xx_eth.h>
 #include <linux/gpio.h>
@@ -42,6 +43,10 @@
 	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
 };
 
+static struct mv_sata_platform_data sheeva_esata_sata_data = {
+	.n_ports	= 2,
+};
+
 static struct mvsdio_platform_data sheevaplug_mvsdio_data = {
 	/* unfortunately the CD signal has not been connected */
 };
@@ -91,6 +96,11 @@
 	kirkwood_ehci_init();
 
 	kirkwood_ge00_init(&sheevaplug_ge00_data);
+
+	/* honor lower power consumption for plugs with out eSATA */
+	if (machine_is_sheeva_esata())
+		kirkwood_sata_init(&sheeva_esata_sata_data);
+
 	kirkwood_sdio_init(&sheevaplug_mvsdio_data);
 
 	platform_device_register(&sheevaplug_leds);

For completeness, these patches do require a current arm/tools/mach-types.

During my excursions with the new hardware, it was pointed out that the Sheeva u-boot 3.4.19 does not properly initialize the SoC SATA ports disallowing further usage; indifferent to the above patches. The "net"
http://plugcomputer.org/plugforum/index.php?topic=927.0 told me to use u-boot 3.4.19 intended for the openrd hardware, and it worked.

Signature · 10 lines
John Holland

___________________________________________

Cellent Finance Solutions AG

Firmensitz: Calwer Stra?e 33, 70173 Stuttgart
Registergericht: Amtsgericht Stuttgart, HRB 720743
Vorstand: Thomas Wild
Vorsitzender des Aufsichtsrats: Rudolf Zipf
#1 lore raw
Quoted 8 lines · John Holland

Hi there,

included are two patches. The first enables Kconfig and basic board support for the eSATA version of the SheevaPlug found at
http://www.newit.co.uk/store/index.php?main_page=index&cPath=3. No, I have no affiliation. The second enables the SATA interfaces on the SoC to allow eSATA visibility.

Quoted 4 lines

I'm opening a discussion to help us decide if the first patch is necessary. Please keep in mind, I also have a third non-disclosed patch that enables SD WP/CD on the same hardware: I have seen that the SoC MPP is also connected to the SD card interface.

Please make those 3 separate patches. And yes I think you need the first patch as well. Some code will be optimized away at compile time if one of the configs is not selected.

Quoted 2 lines

Please pardon my git ignorance, but I couldn't find any guidelines forcing me to use it here.

You're not forced to use Git. However I'd prefer if you could post those patches separately, one per message, with some explanation blurb for each patch and a SOB tag. See Documentation/SubmittingPatches for all the details (apply what makes sense).

Quoted 5 lines

During my excursions with the new hardware, it was pointed out that the Sheeva u-boot 3.4.19 does not properly initialize the SoC SATA ports disallowing further usage; indifferent to the above patches. The "net"
http://plugcomputer.org/plugforum/index.php?topic=927.0 told me to use u-boot 3.4.19 intended for the openrd hardware, and it worked.

That would be good if someone made the necessary patch to add the proper initialization to the kernel eventually.

Nicolas

#2 lore raw

PATCH 1/1 1/3 kirkwood/sheeva: basic board support

Allow basic eSATA SheevaPlug board configuration and build.

--

arch/arm/mach-kirkwood/Kconfig +6 -0
diff -Naur linux-2.6-2.6.32/arch/arm/mach-kirkwood/Kconfig linux-2.6-2.6.32.new/arch/arm/mach-kirkwood/Kconfig
@@ -32,6 +32,12 @@
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell SheevaPlug Reference Board.
 
+config MACH_ESATA_SHEEVAPLUG
+	bool "Marvell eSATA SheevaPlug Reference Board"
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  Marvell eSATA SheevaPlug Reference Board.
+
 config MACH_TS219
 	bool "QNAP TS-119 and TS-219 Turbo NAS"
 	help
arch/arm/mach-kirkwood/Makefile +1 -0
diff -Naur linux-2.6-2.6.32/arch/arm/mach-kirkwood/Makefile linux-2.6-2.6.32.new/arch/arm/mach-kirkwood/Makefile
@@ -5,6 +5,7 @@
 obj-$(CONFIG_MACH_RD88F6281)		+= rd88f6281-setup.o
 obj-$(CONFIG_MACH_MV88F6281GTW_GE)	+= mv88f6281gtw_ge-setup.o
 obj-$(CONFIG_MACH_SHEEVAPLUG)		+= sheevaplug-setup.o
+obj-$(CONFIG_MACH_ESATA_SHEEVAPLUG)	+= sheevaplug-setup.o
 obj-$(CONFIG_MACH_TS219)		+= ts219-setup.o
 obj-$(CONFIG_MACH_OPENRD_BASE)		+= openrd_base-setup.o
 
arch/arm/mach-kirkwood/sheevaplug-setup.c +14 -0
diff -Naur linux-2.6-2.6.32/arch/arm/mach-kirkwood/sheevaplug-setup.c linux-2.6-2.6.32.new/arch/arm/mach-kirkwood/sheevaplug-setup.c
@@ -96,6 +96,7 @@
 	platform_device_register(&sheevaplug_leds);
 }
 
+#ifdef CONFIG_MACH_SHEEVAPLUG
 MACHINE_START(SHEEVAPLUG, "Marvell SheevaPlug Reference Board")
 	/* Maintainer: shadi Ammouri <[email protected]> */
 	.phys_io	= KIRKWOOD_REGS_PHYS_BASE,
@@ -106,3 +107,16 @@
 	.init_irq	= kirkwood_init_irq,
 	.timer		= &kirkwood_timer,
 MACHINE_END
+#endif
+
+#ifdef CONFIG_MACH_ESATA_SHEEVAPLUG
+MACHINE_START(ESATA_SHEEVAPLUG, "Marvell eSATA SheevaPlug Reference Board")
+	.phys_io	= KIRKWOOD_REGS_PHYS_BASE,
+	.io_pg_offst	= ((KIRKWOOD_REGS_VIRT_BASE) >> 18) & 0xfffc,
+	.boot_params	= 0x00000100,
+	.init_machine	= sheevaplug_init,
+	.map_io		= kirkwood_map_io,
+	.init_irq	= kirkwood_init_irq,
+	.timer		= &kirkwood_timer,
+MACHINE_END
+#endif
Signature · 10 lines
John Holland

___________________________________________

Cellent Finance Solutions AG

Firmensitz: Calwer Stra?e 33, 70173 Stuttgart
Registergericht: Amtsgericht Stuttgart, HRB 720743
Vorstand: Thomas Wild
Vorsitzender des Aufsichtsrats: Rudolf Zipf
#3 lore raw

PATCH 1/1 2/3 kirkwood/sheeva: configure SoC SATA interface

In reply to Nicolas Pitre

Enable the kirkwood SATA SoC interface on the eSATA SheevaPlug.

--

arch/arm/mach-kirkwood/sheevaplug-setup.c +10 -0
diff -Naur linux-2.6-2.6.32/arch/arm/mach-kirkwood/sheevaplug-setup.c linux-2.6-2.6.32.new/arch/arm/mach-kirkwood/sheevaplug-setup.c
@@ -11,6 +11,7 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
+#include <linux/ata_platform.h>
 #include <linux/mtd/partitions.h>
 #include <linux/mv643xx_eth.h>
 #include <linux/gpio.h>
@@ -42,6 +43,10 @@
 	.phy_addr	= MV643XX_ETH_PHY_ADDR(0),
 };
 
+static struct mv_sata_platform_data sheeva_esata_sata_data = {
+	.n_ports	= 2,
+};
+
 static struct mvsdio_platform_data sheevaplug_mvsdio_data = {
 	/* unfortunately the CD signal has not been connected */
 };
@@ -91,6 +96,11 @@
 	kirkwood_ehci_init();
 
 	kirkwood_ge00_init(&sheevaplug_ge00_data);
+
+	/* honor lower power consumption for plugs with out eSATA */
+	if (machine_is_sheeva_esata())
+		kirkwood_sata_init(&sheeva_esata_sata_data);
+
 	kirkwood_sdio_init(&sheevaplug_mvsdio_data);
 
 	platform_device_register(&sheevaplug_leds);
Signature · 10 lines
John Holland

___________________________________________

Cellent Finance Solutions AG

Firmensitz: Calwer Stra?e 33, 70173 Stuttgart
Registergericht: Amtsgericht Stuttgart, HRB 720743
Vorstand: Thomas Wild
Vorsitzender des Aufsichtsrats: Rudolf Zipf
#4 lore raw

PATCH 1/1 3/3 kirkwood/sheeva: correlate MPP to SD CD and SD WP

In reply to Nicolas Pitre

Accept SD CD and SD WP in accordance to
http://plugcomputer.org/data/docs/Sheeva-PowerPlug-V1.3-GTI-090906.pdf
on MPP 47 and 44 respectively on the eSATA SheevaPlug

--

arch/arm/mach-kirkwood/sheevaplug-setup.c +24 -2
diff -Naur linux-2.6-2.6.32/arch/arm/mach-kirkwood/sheevaplug-setup.c linux-2.6-2.6.32.new/arch/arm/mach-kirkwood/sheevaplug-setup.c
@@ -51,6 +51,11 @@
 	/* unfortunately the CD signal has not been connected */
 };
 
+static struct mvsdio_platform_data sheeva_esata_mvsdio_data = {
+	.gpio_write_protect = 44, /* MPP44 used as SD write protect */
+	.gpio_card_detect = 47,	  /* MPP47 used as SD card detect */
+};
+
 static struct gpio_led sheevaplug_led_pins[] = {
 	{
 		.name			= "plug:green:health",
@@ -79,13 +84,26 @@
 	0
 };
 
+static unsigned int sheeva_esata_mpp_config[] __initdata = {
+	MPP29_GPIO,	/* USB Power Enable */
+	MPP44_GPIO,	/* SD Write Protect */
+	MPP47_GPIO,	/* SD Card Detect */
+	MPP49_GPIO,	/* LED Green */
+	0
+};
+
 static void __init sheevaplug_init(void)
 {
 	/*
 	 * Basic setup. Needs to be called early.
 	 */
 	kirkwood_init();
-	kirkwood_mpp_conf(sheevaplug_mpp_config);
+
+	/* setup gpio pin select */
+	if (machine_is_sheeva_esata())
+		kirkwood_mpp_conf(sheeva_esata_mpp_config);
+	else
+		kirkwood_mpp_conf(sheevaplug_mpp_config);
 
 	kirkwood_uart0_init();
 	kirkwood_nand_init(ARRAY_AND_SIZE(sheevaplug_nand_parts), 25);
@@ -101,7 +119,11 @@
 	if (machine_is_sheeva_esata())
 		kirkwood_sata_init(&sheeva_esata_sata_data);
 
-	kirkwood_sdio_init(&sheevaplug_mvsdio_data);
+ 	/* enable sd wp and sd cd on plugs with esata */
+ 	if (machine_is_sheeva_esata())
+ 		kirkwood_sdio_init(&sheeva_esata_mvsdio_data);
+ 	else
+ 		kirkwood_sdio_init(&sheevaplug_mvsdio_data);
 
 	platform_device_register(&sheevaplug_leds);
 }

Although this has not yet been thoroughly tested, it has no noticeable adverse effects.

Signature · 10 lines
John Holland

___________________________________________

Cellent Finance Solutions AG

Firmensitz: Calwer Stra?e 33, 70173 Stuttgart
Registergericht: Amtsgericht Stuttgart, HRB 720743
Vorstand: Thomas Wild
Vorsitzender des Aufsichtsrats: Rudolf Zipf