OMAP3: PM: Smartreflex and voltage revamp
Subsystems (5)
v3 cover OMAP3: PM: Smartreflex and voltage revamp
The main motivations behind this patch series are the following
1. Making smartreflex a platform driver with omap-device layer.
2. Separating voltage specific code from smartreflex.c and other locations and consolidating them into voltage.c and voltage.h.
3. Smartreflex module can have Class 1 Class 2 or Class 3 implementations depending on the PMIC in use. Making smartreflex.c capable of handling both the Class 2 and 3 implementaions and separating out class specific code into a separate class driver.
4. Remove dependencies on opp id in the smartreflex and voltage drivers
5. Implementating latest TI recommended register settings for Smartreflex and Voltage processor module as well as recommended sequences for enabling and disabling of Smartreflex and Voltage processor modules.
6. Implementing VP force update method of voltage scaling which is again TI hardware recommended.
What this patch series does not address are
1. Separating PMIC specific portions from smartreflex and voltage code.
2. OMAP3630 and OMP4 smartreflex support.
This patch series is based on Kevin's PM tree origin/pm-wip-opp branch and is dependent on the following patches not yet applied onto this branch.
http://patchwork.kernel.org/patch/81504/ http://patchwork.kernel.org/patch/81606/
This patch series has been tested on OMAP3430 SDP with basic power management tests including the dvfs scripts.
Thara Gopinath (22):
OMAP3: PM: Adding hwmod data for Smartreflex
OMAP3: PM: Create list to keep track of various smartreflex
instances.
OMAP3: PM: Convert smartreflex driver into a platform driver using
hwmods and omap-device layer
OMAP3: PM: Move smartreflex autocompensation enable disable hooks to
PM debugfs.
OMAP3: PM: Remove OPP id dependency from smartreflex driver
OMAP3: PM: Correcting API names in samrtreflex driver.
OMAP3: PM: Smartreflex class related changes for smartreflex.c
OMAP3: PM: Adding smartreflex class 3 driver.
OMAP3: PM: Creating separate files for handling OMAP3 voltage related
operations.
OMAP3: PM: Adding voltage table support in voltage driver.
OMAP3: PM: Removing VP1, VP2, SR1 and SR2 defintions.
OMAP3: PM: Minimizing the passing around of sr id in smartreflex.c
OMAP3: PM: Cleaning up of smartreflex header file.
OMAP3: PM: Configurations for Smartreflex Class 2 and Smartreflex
Class 3
OMAP3: PM: Support for enabling smartreflex autocompensation by
default.
OMAP3: PM: Correcting accessing of ERRCONFIG register in
smartreflex.c
OMAP3: PM: Implement latest h/w recommendations for SR and VP
registers and SR VP enable disable sequence.
OMAP3: PM: Optional reset of voltage during Smartreflex disable.
OMAP3: PM: Disabling Smartreflex across both frequency and voltage
scaling during DVFS.
OMAP3: PM: VP force update method of voltage scaling
OMAP3: PM: Enabling Smartreflex Class 3 driver by default in pm
defconfig
OMAP3: PM: Fix crash when enabling SmartReflex on non-supported
OMAPs.
arch/arm/configs/omap3_pm_defconfig | 1 + arch/arm/mach-omap2/Makefile | 6 +- arch/arm/mach-omap2/board-3430sdp.c | 5 +- arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 134 +++ arch/arm/mach-omap2/pm-debug.c | 4 +- arch/arm/mach-omap2/pm.h | 7 - arch/arm/mach-omap2/pm34xx.c | 95 +-- arch/arm/mach-omap2/resource34xx.c | 27 +- arch/arm/mach-omap2/resource34xx.h | 1 - arch/arm/mach-omap2/smartreflex-class3.c | 60 ++ arch/arm/mach-omap2/smartreflex-class3.h | 18 + arch/arm/mach-omap2/smartreflex.c | 1302 ++++++++++------------------ arch/arm/mach-omap2/smartreflex.h | 350 ++++---- arch/arm/mach-omap2/sr_device.c | 152 ++++ arch/arm/mach-omap2/voltage.c | 940 ++++++++++++++++++++ arch/arm/mach-omap2/voltage.h | 99 +++ arch/arm/plat-omap/Kconfig | 11 +- 17 files changed, 2088 insertions(+), 1124 deletions(-) create mode 100644 arch/arm/mach-omap2/smartreflex-class3.c create mode 100644 arch/arm/mach-omap2/smartreflex-class3.h create mode 100644 arch/arm/mach-omap2/sr_device.c create mode 100644 arch/arm/mach-omap2/voltage.c create mode 100644 arch/arm/mach-omap2/voltage.h
PATCH v3 1/22 OMAP3: PM: Adding hwmod data for Smartreflex
This patch adds the hwmod strucutres and other hwmod data for OMAP3 Smartreflex IP's.
--- arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 135 ++++++++++++++++++++++++++++ arch/arm/mach-omap2/smartreflex.h | 33 +++++++ 2 files changed, 168 insertions(+), 0 deletions(-)
arch/arm/mach-omap2/omap_hwmod_3xxx_data.c +135 -0
@@ -17,10 +17,12 @@#include <mach/irqs.h> #include <plat/cpu.h> #include <plat/dma.h> +#include <plat/control.h> #include "omap_hwmod_common_data.h" #include "prm-regbits-34xx.h" +#include "smartreflex.h" /* * OMAP3xxx hardware module integration data
@@ -35,6 +37,8 @@ static struct omap_hwmod omap3xxx_mpu_hwmod;static struct omap_hwmod omap3xxx_l3_hwmod;static struct omap_hwmod omap3xxx_l4_core_hwmod;static struct omap_hwmod omap3xxx_l4_per_hwmod; +static struct omap_hwmod omap34xx_sr1_hwmod; +static struct omap_hwmod omap34xx_sr2_hwmod;/* L3 -> L4_CORE interface */ static struct omap_hwmod_ocp_if omap3xxx_l3__l4_core = {
@@ -88,9 +92,47 @@ static struct omap_hwmod_ocp_if omap3xxx_l4_core__l4_wkup = { .user = OCP_USER_MPU | OCP_USER_SDMA, }; +/* L4 CORE -> SR1 interface */ +static struct omap_hwmod_addr_space omap34xx_sr1_addr_space[] = { + { + .pa_start =OMAP34XX_SR1_BASE , + .pa_end =OMAP34XX_SR1_BASE +SZ_1K -1 , + .flags =ADDR_TYPE_RT , + }, +}; + +static struct omap_hwmod_ocp_if omap3_l4_core__sr1 = { + .master = &omap3xxx_l4_core_hwmod, + .slave = &omap34xx_sr1_hwmod, + .clk ="sr_l4_ick" , + .addr = omap34xx_sr1_addr_space, + .addr_cnt =ARRAY_SIZE (omap34xx_sr1_addr_space), + .user =OCP_USER_MPU , +}; + +/* L4 CORE -> SR1 interface */ +static struct omap_hwmod_addr_space omap34xx_sr2_addr_space[] = { + { + .pa_start =OMAP34XX_SR2_BASE , + .pa_end =OMAP34XX_SR2_BASE +SZ_1K -1 , + .flags =ADDR_TYPE_RT , + }, +}; + +static struct omap_hwmod_ocp_if omap3_l4_core__sr2 = { + .master = &omap3xxx_l4_core_hwmod, + .slave = &omap34xx_sr2_hwmod, + .clk ="sr_l4_ick" , + .addr = omap34xx_sr2_addr_space, + .addr_cnt =ARRAY_SIZE (omap34xx_sr2_addr_space), + .user =OCP_USER_MPU , +}; +/* Slave interfaces on the L4_CORE interconnect */ static struct omap_hwmod_ocp_if *omap3xxx_l4_core_slaves[] = { &omap3xxx_l3__l4_core, + &omap3_l4_core__sr1, + &omap3_l4_core__sr2, };/* Master interfaces on the L4_CORE interconnect */
@@ -164,12 +206,105 @@ static struct omap_hwmod omap3xxx_mpu_hwmod = { .omap_chip = OMAP_CHIP_INIT(CHIP_IS_OMAP3430), }; +/* SR common */ +static struct omap_hwmod_sysc_fields omap34xx_sr_sysc_fields = { + .clkact_shift =20 , +}; + +static struct omap_hwmod_class_sysconfig omap34xx_sr_sysc = { + .sysc_offs =0x24 , + .sysc_flags = (SYSC_HAS_CLOCKACTIVITY |SYSC_NO_CACHE ), + .clockact =CLOCKACT_TEST_ICLK , + .sysc_fields = &omap34xx_sr_sysc_fields, +}; + +static struct omap_hwmod_class omap34xx_smartreflex_hwmod_class = { + .name ="smartreflex" , + .sysc = &omap34xx_sr_sysc, + .rev =1 , +}; + +/* SR1 */ +static struct omap_hwmod_ocp_if *omap34xx_sr1_slaves[] = { + &omap3_l4_core__sr1, +}; + +static u32 omap34xx_sr1_efuse_offs[] = { +OMAP343X_CONTROL_FUSE_OPP1_VDD1 ,OMAP343X_CONTROL_FUSE_OPP2_VDD1 , +OMAP343X_CONTROL_FUSE_OPP3_VDD1 ,OMAP343X_CONTROL_FUSE_OPP4_VDD1 , +OMAP343X_CONTROL_FUSE_OPP5_VDD1 , +}; + +static u32 omap34xx_sr1_test_nvalues[] = { +0x9A90E6 ,0xAABE9A ,0xBBF5C5 ,0xBBB292 ,0xBBF5C5 , +}; + +static struct omap_smartreflex_dev_data omap34xx_sr1_dev_attr = { + .volts_supported =5 , + .efuse_sr_control =OMAP343X_CONTROL_FUSE_SR , + .sennenable_shift =OMAP343X_SR1_SENNENABLE_SHIFT , + .senpenable_shift =OMAP343X_SR1_SENPENABLE_SHIFT , + .efuse_nvalues_offs = omap34xx_sr1_efuse_offs, + .test_sennenable =0x3 , + .test_senpenable =0x3 , + .test_nvalues = omap34xx_sr1_test_nvalues +}; + +static struct omap_hwmod omap34xx_sr1_hwmod = { + .name ="sr1_hwmod" , + .class = &omap34xx_smartreflex_hwmod_class, + .main_clk ="sr1_fck" , + .slaves = omap34xx_sr1_slaves, + .slaves_cnt =ARRAY_SIZE (omap34xx_sr1_slaves), + .dev_attr = &omap34xx_sr1_dev_attr, + .omap_chip =OMAP_CHIP_INIT (CHIP_IS_OMAP3430 ), + .flags =HWMOD_SET_DEFAULT_CLOCKACT , +}; + +/* SR2 */ +static struct omap_hwmod_ocp_if *omap34xx_sr2_slaves[] = { + &omap3_l4_core__sr2, +}; + +static u32 omap34xx_sr2_efuse_offs[] = { +OMAP343X_CONTROL_FUSE_OPP1_VDD2 ,OMAP343X_CONTROL_FUSE_OPP2_VDD2 , +OMAP343X_CONTROL_FUSE_OPP3_VDD2 , +}; + +static u32 omap34xx_sr2_test_nvalues[] = { +0x0 ,0xAAC098 ,0xAB89D9 +}; + +static struct omap_smartreflex_dev_data omap34xx_sr2_dev_attr = { + .volts_supported =3 , + .efuse_sr_control =OMAP343X_CONTROL_FUSE_SR , + .sennenable_shift =OMAP343X_SR2_SENNENABLE_SHIFT , + .senpenable_shift =OMAP343X_SR2_SENPENABLE_SHIFT , + .efuse_nvalues_offs = omap34xx_sr2_efuse_offs, + .test_sennenable =0x3 , + .test_senpenable =0x3 , + .test_nvalues = omap34xx_sr2_test_nvalues +}; + +static struct omap_hwmod omap34xx_sr2_hwmod = { + .name ="sr2_hwmod" , + .class = &omap34xx_smartreflex_hwmod_class, + .main_clk ="sr2_fck" , + .slaves = omap34xx_sr2_slaves, + .slaves_cnt =ARRAY_SIZE (omap34xx_sr2_slaves), + .dev_attr = &omap34xx_sr2_dev_attr, + .omap_chip =OMAP_CHIP_INIT (CHIP_IS_OMAP3430 ), + .flags =HWMOD_SET_DEFAULT_CLOCKACT , +}; +static __initdata struct omap_hwmod *omap3xxx_hwmods[] = { &omap3xxx_l3_hwmod, &omap3xxx_l4_core_hwmod, &omap3xxx_l4_per_hwmod, &omap3xxx_l4_wkup_hwmod, &omap3xxx_mpu_hwmod, + &omap34xx_sr1_hwmod, + &omap34xx_sr2_hwmod,NULL , };
arch/arm/mach-omap2/smartreflex.h +33 -0
@@ -237,6 +237,39 @@ extern u32 current_vdd2_opp;#define SR_TESTING_NVALUES 0#endif +/** +* omap_smartreflex_dev_data - Smartreflex device specific data +* +* @volts_supported : Number of distinct voltages possible for the VDD +* associated with this smartreflex module. +* @efuse_sr_control : The regisrter offset of control_fuse_sr efuse +* register from which sennenable and senpenable values +* are obtained. +* @sennenable_shift : The shift in the control_fuse_sr register for +* obtaining the sennenable value for this smartreflex +* module. +* @senpenable_shift : The shift in the control_fuse_sr register for +* obtaining the senpenable value for this smartreflex +* module. +* @efuse_nvalues_offs : Array of efuse offsets from which ntarget values can +* be retrieved. Number of efuse offsets in this arrray +* is equal to the volts_supported value ie one efuse +* register per supported voltage. +* @test_sennenable : SENNENABLE test value +* @test_senpenable : SENPENABLE test value. +* @test_nvalues : Array of test ntarget values. +*/ +struct omap_smartreflex_dev_data { +int volts_supported; +u32 efuse_sr_control; +u32 sennenable_shift; +u32 senpenable_shift; +u32 *efuse_nvalues_offs; +u32 test_sennenable; +u32 test_senpenable; +u32 *test_nvalues; +}; +/* * Smartreflex module enable/disable interface. * NOTE: if smartreflex is not enabled from sysfs, these functions will not
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 2/22 OMAP3: PM: Create list to keep track of various smartreflex instances.
This patch removes the pointer sr1, sr2 in smartreflex.c and instead creatse a list for keeping track of multiple smartreflex instances.. This makes it scalable for next gen OMAPs where there are more than two smartreflex modules.
--- arch/arm/mach-omap2/smartreflex.c | 114 ++++++++++++++++++++++++------------ 1 files changed, 76 insertions(+), 38 deletions(-)
arch/arm/mach-omap2/smartreflex.c +76 -38
@@ -26,6 +26,7 @@#include <linux/kobject.h> #include <linux/i2c/twl.h> #include <linux/io.h> +#include <linux/list.h> #include <plat/omap34xx.h> #include <plat/control.h>
@@ -51,9 +52,12 @@ struct omap_sr {u32 opp5_nvalue;u32 senp_mod, senn_mod;void __iomem *srbase_addr; -void __iomem *vpbase_addr; +struct list_head node; }; +/* sr_list contains all the instances of smartreflex module */ +static LIST_HEAD (sr_list); +#define SR_REGADDR (offs) (sr->srbase_addr + offset)static inline void sr_write_reg (struct omap_sr *sr,unsigned offset,u32 value)
@@ -78,6 +82,20 @@ static inline u32 sr_read_reg(struct omap_sr *sr, unsigned offset)return __raw_readl (SR_REGADDR (offset)); } +static struct omap_sr *_sr_lookup (int srid) +{ +struct omap_sr *sr_info, *temp_sr_info; + + sr_info =NULL ; +list_for_each_entry (temp_sr_info, &sr_list, node) { +if (srid == temp_sr_info->srid) { + sr_info = temp_sr_info; +break ; + } + } +return sr_info; +} +static int sr_clk_enable (struct omap_sr *sr) {if (clk_enable (sr->clk) !=0 ) {
@@ -151,11 +169,17 @@ static u8 get_vdd1_opp(void) {struct omap_opp *opp;unsigned long freq; +struct omap_sr *sr_info =_sr_lookup (SR1 ); -if (sr1.vdd_opp_clk ==NULL ||IS_ERR (sr1.vdd_opp_clk)) +if (!sr_info) { +pr_warning ("omap_sr struct corresponding to SR1 not found\n" ); +return 0 ; + } + +if (sr_info->vdd_opp_clk ==NULL ||IS_ERR (sr_info->vdd_opp_clk))return 0 ; - freq = sr1.vdd_opp_clk->rate; + freq = sr_info->vdd_opp_clk->rate; opp =opp_find_freq_ceil (OPP_MPU , &freq);if (IS_ERR (opp))return 0 ;
@@ -163,9 +187,9 @@ static u8 get_vdd1_opp(void)* Use higher freq voltage even if an exact match is not available * we are probably masking a clock framework bug, so warn */ -if (unlikely (freq != sr1.vdd_opp_clk->rate)) +if (unlikely (freq != sr_info->vdd_opp_clk->rate))pr_warning ("%s: Available freq %ld != dpll freq %ld.\n" , - __func__, freq, sr1.vdd_opp_clk->rate); + __func__, freq, sr_info->vdd_opp_clk->rate);return opp_get_opp_id (opp); }
@@ -174,11 +198,17 @@ static u8 get_vdd2_opp(void) {struct omap_opp *opp;unsigned long freq; +struct omap_sr *sr_info =_sr_lookup (SR2 ); + +if (!sr_info) { +pr_warning ("omap_sr struct corresponding to SR2 not found\n" ); +return 0 ; + } -if (sr2.vdd_opp_clk ==NULL ||IS_ERR (sr2.vdd_opp_clk)) +if (sr_info->vdd_opp_clk ==NULL ||IS_ERR (sr_info->vdd_opp_clk))return 0 ; - freq = sr2.vdd_opp_clk->rate; + freq = sr_info->vdd_opp_clk->rate; opp =opp_find_freq_ceil (OPP_L3 , &freq);if (IS_ERR (opp))return 0 ;
@@ -187,9 +217,9 @@ static u8 get_vdd2_opp(void)* Use higher freq voltage even if an exact match is not available * we are probably masking a clock framework bug, so warn */ -if (unlikely (freq != sr2.vdd_opp_clk->rate)) +if (unlikely (freq != sr_info->vdd_opp_clk->rate))pr_warning ("%s: Available freq %ld != dpll freq %ld.\n" , - __func__, freq, sr2.vdd_opp_clk->rate); + __func__, freq, sr_info->vdd_opp_clk->rate);return opp_get_opp_id (opp); }
@@ -694,14 +724,13 @@ static void sr_disable(struct omap_sr *sr)void sr_start_vddautocomap (int srid,u32 target_opp_no) { -struct omap_sr *sr =NULL ; +struct omap_sr *sr =_sr_lookup (srid); -if (srid ==SR1 ) - sr = &sr1; -else if (srid ==SR2 ) - sr = &sr2; -else +if (!sr) { +pr_warning ("omap_sr struct corresponding to SR%d not found\n" , + srid);return ; + }if (sr->is_sr_reset ==1 ) {sr_clk_enable (sr);
@@ -719,14 +748,13 @@ EXPORT_SYMBOL(sr_start_vddautocomap);int sr_stop_vddautocomap (int srid) { -struct omap_sr *sr =NULL ; +struct omap_sr *sr =_sr_lookup (srid); -if (srid ==SR1 ) - sr = &sr1; -else if (srid ==SR2 ) - sr = &sr2; -else -return -EINVAL ; +if (!sr) { +pr_warning ("omap_sr struct corresponding to SR%d not found\n" , + srid); +return false; + }if (sr->is_autocomp_active ==1 ) {sr_disable (sr);
@@ -744,14 +772,13 @@ EXPORT_SYMBOL(sr_stop_vddautocomap);void enable_smartreflex (int srid) {u32 target_opp_no =0 ; -struct omap_sr *sr =NULL ; +struct omap_sr *sr =_sr_lookup (srid); -if (srid ==SR1 ) - sr = &sr1; -else if (srid ==SR2 ) - sr = &sr2; -else +if (!sr) { +pr_warning ("omap_sr struct corresponding to SR%d not found\n" , + srid);return ; + }if (sr->is_autocomp_active ==1 ) {if (sr->is_sr_reset ==1 ) {
@@ -779,15 +806,13 @@ void enable_smartreflex(int srid)void disable_smartreflex (int srid) {u32 i =0 ; +struct omap_sr *sr =_sr_lookup (srid); -struct omap_sr *sr =NULL ; - -if (srid ==SR1 ) - sr = &sr1; -else if (srid ==SR2 ) - sr = &sr2; -else +if (!sr) { +pr_warning ("omap_sr struct corresponding to SR%d not found\n" , + srid);return ; + }if (sr->is_autocomp_active ==1 ) {if (sr->is_sr_reset ==0 ) {
@@ -920,7 +945,13 @@ int sr_voltagescale_vcbypass(u32 target_opp, u32 current_opp,static ssize_t omap_sr_vdd1_autocomp_show (struct kobject *kobj,struct kobj_attribute *attr,char *buf) { -return sprintf (buf,"%d\n" , sr1.is_autocomp_active); +struct omap_sr *sr_info =_sr_lookup (SR1 ); + +if (!sr_info) { +pr_warning ("omap_sr struct corresponding to SR1 not found\n" ); +return 0 ; + } +return sprintf (buf,"%d\n" , sr_info->is_autocomp_active); } static ssize_t omap_sr_vdd1_autocomp_store(struct kobject *kobj,
@@ -960,7 +991,13 @@ static struct kobj_attribute sr_vdd1_autocomp = {static ssize_t omap_sr_vdd2_autocomp_show (struct kobject *kobj,struct kobj_attribute *attr,char *buf) { -return sprintf (buf,"%d\n" , sr2.is_autocomp_active); +struct omap_sr *sr_info =_sr_lookup (SR2 ); + +if (!sr_info) { +pr_warning ("omap_sr struct corresponding to SR2 not found\n" ); +return 0 ; + } +return sprintf (buf,"%d\n" , sr_info->is_autocomp_active); } static ssize_t omap_sr_vdd2_autocomp_store(struct kobject *kobj,
@@ -1010,7 +1047,6 @@ static int __init omap3_sr_init(void) RdReg |=DCDC_GLOBAL_CFG_ENABLE_SRFLX ; ret |=twl_i2c_write_u8 (TWL4030_MODULE_PM_RECEIVER , RdReg,R_DCDC_GLOBAL_CFG ); -if (cpu_is_omap34xx ()) { sr1.clk =clk_get (NULL ,"sr1_fck" ); sr2.clk =clk_get (NULL ,"sr2_fck" );
@@ -1036,6 +1072,8 @@ static int __init omap3_sr_init(void) ret =sysfs_create_file (power_kobj, &sr_vdd2_autocomp.attr);if (ret)pr_err ("sysfs_create_file failed: %d\n" , ret); +list_add (&sr1.node, &sr_list); +list_add (&sr2.node, &sr_list);return 0 ; }
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 3/22 OMAP3: PM: Convert smartreflex driver into a platform driver using hwmods and omap-device layer
This patch converts the exisitng smartreflex library into a platform driver with device , driver registrations using hardware mods. As part of this Ntarget values are passed as platform data.
--- arch/arm/mach-omap2/Makefile | 2 +- arch/arm/mach-omap2/smartreflex.c | 325 +++++++++++++------------------------ arch/arm/mach-omap2/smartreflex.h | 26 +++ arch/arm/mach-omap2/sr_device.c | 139 ++++++++++++++++ 4 files changed, 278 insertions(+), 214 deletions(-) create mode 100644 arch/arm/mach-omap2/sr_device.c
arch/arm/mach-omap2/Makefile +1 -1
@@ -48,7 +48,7 @@ obj-$(CONFIG_ARCH_OMAP2) += pm24xx.o obj-$(CONFIG_ARCH_OMAP2) += sleep24xx.o obj-$(CONFIG_ARCH_OMAP3) += pm34xx.o sleep34xx.o cpuidle34xx.o obj-$(CONFIG_PM_DEBUG) += pm-debug.o -obj-$(CONFIG_OMAP_SMARTREFLEX) += smartreflex.o +obj-$(CONFIG_OMAP_SMARTREFLEX) += sr_device.o smartreflex.o AFLAGS_sleep24xx.o :=-Wa,-march=armv6 AFLAGS_sleep34xx.o :=-Wa,-march=armv7-a
arch/arm/mach-omap2/smartreflex.c +112 -213
445 lines not on this page · raw message
arch/arm/mach-omap2/smartreflex.h +26 -0
@@ -14,6 +14,8 @@* published by the Free Software Foundation. */ +#include <linux/platform_device.h> +#define PHY_TO_OFF_PM_MASTER (p) (p - 0x36)#define PHY_TO_OFF_PM_RECIEVER (p) (p - 0x5b)#define PHY_TO_OFF_PM_INT (p) (p - 0x2e)
@@ -276,6 +278,30 @@ struct omap_smartreflex_dev_data {* do anything. */ #ifdef CONFIG_OMAP_SMARTREFLEX +/** +* omap_smartreflex_data - Smartreflex platform data +* +* @senp_mod : SENPENABLE value for the sr +* @senn_mod : SENNENABLE value for sr +* @sr_nvalue : array of n target values for sr +* @enable_on_init : whether this sr module needs to enabled at +* boot up or not +* @device_enable : fn pointer to be populated with omap_device +* enable API +* @device_shutdown : fn pointer to be populated with omap_device +* shutdown API +* @device_idle : fn pointer to be pouplated with omap_device idle API +*/ +struct omap_smartreflex_data { +u32 senp_mod; +u32 senn_mod; +u32 *sr_nvalue; +bool enable_on_init; +int (*device_enable)(struct platform_device *pdev); +int (*device_shutdown)(struct platform_device *pdev); +int (*device_idle)(struct platform_device *pdev); +}; +void enable_smartreflex (int srid);void disable_smartreflex (int srid);int sr_voltagescale_vcbypass (u32 t_opp,u32 c_opp,u8 t_vsel,u8 c_vsel);
arch/arm/mach-omap2/sr_device.c new file +139 -0
139 lines not on this page · raw message
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 4/22 OMAP3: PM: Move smartreflex autocompensation enable disable hooks to PM debugfs.
This patch moves the hooks to enable disable smartreflex autocompensation to pm debugfs from the /sys/power/.
To enable autocompensation for smartreflex SR<n> do
echo 1 > <path>/pm_debug/sr<n>_autocomp
To disable autocompensation for smartreflex SR<n> do
echo 0 > <path>/pm_debug/sr<n>_autocomp--- arch/arm/mach-omap2/pm-debug.c | 4 +- arch/arm/mach-omap2/smartreflex.c | 114 ++++++++++-------------------------- arch/arm/mach-omap2/smartreflex.h | 2 + 3 files changed, 36 insertions(+), 84 deletions(-)
arch/arm/mach-omap2/pm-debug.c +2 -2
@@ -162,7 +162,7 @@ void omap2_pm_dump(int mode, int resume, unsigned int us)static void pm_dbg_regset_store (u32 *ptr); -struct dentry *pm_dbg_dir; +struct dentry *pm_dbg_dir, *pm_dbg_main_dir;static int pm_dbg_init_done;
@@ -613,7 +613,7 @@ static int __init pm_dbg_init(void)S_IRUGO |S_IWUGO , d, &voltage_off_while_idle, &pm_dbg_option_fops); - + pm_dbg_main_dir = d; pm_dbg_init_done =1 ;return 0 ;
arch/arm/mach-omap2/smartreflex.c +32 -82
168 lines not on this page · raw message
arch/arm/mach-omap2/smartreflex.h +2 -0
@@ -16,6 +16,8 @@#include <linux/platform_device.h> +extern struct dentry *pm_dbg_main_dir; +#define PHY_TO_OFF_PM_MASTER (p) (p - 0x36)#define PHY_TO_OFF_PM_RECIEVER (p) (p - 0x5b)#define PHY_TO_OFF_PM_INT (p) (p - 0x2e)
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 5/22 OMAP3: PM: Remove OPP id dependency from smartreflex driver
This patch removes get_vdd1_opp and get_vdd2_opp API's and replaces them with get_curr_vdd1_voltage and get_curr_vdd2_voltage API's. N-target values are now linked to voltages and the link bewtween voltage and n-target values is managed internally in smartreflex driver and sr_devices.c.
get_curr_vdd1_voltage and get_curr_vdd2_voltage are added in smartreflex driver in this patch. These API's will be moved to the voltage driver in a later patch when voltage specific code is separated out of smartreflex. The link between various voltages and n-target values will also be separated out later.
--- arch/arm/mach-omap2/smartreflex.c | 201 +++++++++++++++---------------------- arch/arm/mach-omap2/smartreflex.h | 21 +++- arch/arm/mach-omap2/sr_device.c | 39 ++++++- 3 files changed, 129 insertions(+), 132 deletions(-)
arch/arm/mach-omap2/smartreflex.c +80 -121
@@ -48,7 +48,6 @@ struct omap_sr {int srid;int is_sr_reset;int is_autocomp_active; -struct clk *vdd_opp_clk;u32 clk_length;unsigned int irq;struct platform_device *pdev;
@@ -119,64 +118,65 @@ static void sr_clk_disable(struct omap_sr *sr) sr->is_sr_reset =1 ; } -static u8 get_vdd1_opp (void ) +static unsigned long get_curr_vdd1_voltage (void ) {struct omap_opp *opp;unsigned long freq; -struct omap_sr *sr_info =_sr_lookup (SR1 ); +struct clk *dpll1_clk; -if (!sr_info) { -pr_warning ("omap_sr struct corresponding to SR1 not found\n" ); -return 0 ; - } - -if (sr_info->vdd_opp_clk ==NULL ||IS_ERR (sr_info->vdd_opp_clk)) + dpll1_clk =clk_get (NULL ,"dpll1_ck" ); +if (IS_ERR (dpll1_clk))return 0 ; - freq = sr_info->vdd_opp_clk->rate; - opp =opp_find_freq_ceil (OPP_MPU , &freq); + freq = dpll1_clk->rate;; + opp =opp_find_freq_exact (OPP_MPU , freq,1 );if (IS_ERR (opp))return 0 ; -/* -* Use higher freq voltage even if an exact match is not available -* we are probably masking a clock framework bug, so warn -*/ -if (unlikely (freq != sr_info->vdd_opp_clk->rate)) -pr_warning ("%s: Available freq %ld != dpll freq %ld.\n" , - __func__, freq, sr_info->vdd_opp_clk->rate); -return opp_get_opp_id (opp); +return opp_get_voltage (opp); } -static u8 get_vdd2_opp (void ) +static unsigned long get_curr_vdd2_voltage (void ) {struct omap_opp *opp;unsigned long freq; -struct omap_sr *sr_info =_sr_lookup (SR2 ); +struct clk *l3_clk; -if (!sr_info) { -pr_warning ("omap_sr struct corresponding to SR2 not found\n" ); -return 0 ; - } - -if (sr_info->vdd_opp_clk ==NULL ||IS_ERR (sr_info->vdd_opp_clk)) + l3_clk =clk_get (NULL ,"l3_ick" ); +if (IS_ERR (l3_clk))return 0 ; - freq = sr_info->vdd_opp_clk->rate; - opp =opp_find_freq_ceil (OPP_L3 , &freq); + freq = l3_clk->rate; + opp =opp_find_freq_exact (OPP_L3 , freq,1 );if (IS_ERR (opp))return 0 ; -/* -* Use higher freq voltage even if an exact match is not available -* we are probably masking a clock framework bug, so warn -*/ -if (unlikely (freq != sr_info->vdd_opp_clk->rate)) -pr_warning ("%s: Available freq %ld != dpll freq %ld.\n" , - __func__, freq, sr_info->vdd_opp_clk->rate); -return opp_get_opp_id (opp); +return opp_get_voltage (opp); } +static int sr_match_volt (struct omap_sr *sr,unsigned long volt, +struct omap_volt_data *volt_data) +{ +struct omap_smartreflex_data *pdata = sr->pdev->dev.platform_data; +struct omap_device *odev =to_omap_device (sr->pdev); +struct omap_smartreflex_dev_data *sr_dev_data = + odev->hwmods[0 ]->dev_attr; +int i; + +if (!pdata->sr_volt_data) { +pr_notice ("voltage table does not exist for SR %d\n" , sr->srid); +return false; + } +for (i =0 ; i < sr_dev_data->volts_supported; i++) { +if (pdata->sr_volt_data[i].voltage == volt) { + *volt_data = pdata->sr_volt_data[i]; +return true; + } + } +pr_notice ("Unable to match the current voltage with \ +the voltage table for SR %d\n" , sr->srid); +return false; +}static void sr_set_clk_length (struct omap_sr *sr) {
@@ -211,21 +211,14 @@ static void sr_set_clk_length(struct omap_sr *sr)static void sr_configure_vp (int srid) { -u32 vpconfig; -u32 vsel; -int uvdc; -u32 target_opp_no; -struct omap_opp *opp; +u32 vpconfig, vsel; +unsigned long uvdc;if (srid ==SR1 ) { - target_opp_no =get_vdd1_opp (); -if (!target_opp_no) - target_opp_no =VDD1_OPP3 ; - - opp =opp_find_by_opp_id (OPP_MPU , target_opp_no); -BUG_ON (!opp);/* XXX ugh */ - - uvdc =opp_get_voltage (opp); + uvdc =get_curr_vdd1_voltage (); +if (!uvdc) +pr_err ("Something wrong.Current voltage not obtained \ +from OPP framework for SR %d!\n" , srid); vsel =omap_twl_uv_to_vsel (uvdc); vpconfig = PRM_VP1_CONFIG_ERROROFFSET |
@@ -267,14 +260,10 @@ static void sr_configure_vp(int srid) OMAP3_PRM_VP1_CONFIG_OFFSET); }else if (srid ==SR2 ) { - target_opp_no =get_vdd2_opp (); -if (!target_opp_no) - target_opp_no =VDD2_OPP3 ; - - opp =opp_find_by_opp_id (OPP_L3 , target_opp_no); -BUG_ON (!opp);/* XXX ugh */ - - uvdc =opp_get_voltage (opp); + uvdc =get_curr_vdd2_voltage (); +if (!uvdc) +pr_err ("Something wrong.Current voltage not obtained \ +from OPP framework for SR %d!\n" , srid); vsel =omap_twl_uv_to_vsel (uvdc); vpconfig = PRM_VP2_CONFIG_ERROROFFSET |
@@ -368,9 +357,8 @@ static void sr_configure(struct omap_sr *sr)static int sr_reset_voltage (int srid) { -struct omap_opp *opp;unsigned long uvdc; -u32 target_opp_no, vsel =0 ; +u32 vsel =0 ;u32 reg_addr =0 ;u32 loop_cnt =0 , retries_cnt =0 ;u32 vc_bypass_value;
@@ -379,17 +367,12 @@ static int sr_reset_voltage(int srid)u32 prm_vp1_voltage, prm_vp2_voltage;if (srid ==SR1 ) { - target_opp_no =get_vdd1_opp (); -if (!target_opp_no) { -pr_info ("Current OPP unknown: Cannot reset voltage\n" ); + uvdc =get_curr_vdd1_voltage (); +if (!uvdc) { +pr_err ("Something wrong.Current voltage not obtained \ +from OPP framework for SR %d!\n" , srid);return 1 ; } - - opp =opp_find_by_opp_id (OPP_MPU , target_opp_no); -if (!opp) -return 1 ; - - uvdc =opp_get_voltage (opp); vsel =omap_twl_uv_to_vsel (uvdc); reg_addr =R_VDD1_SR_CONTROL ;
@@ -397,17 +380,12 @@ static int sr_reset_voltage(int srid) OMAP3_PRM_VP1_VOLTAGE_OFFSET); t2_smps_steps =abs (vsel - prm_vp1_voltage); }else if (srid ==SR2 ) { - target_opp_no =get_vdd2_opp (); -if (!target_opp_no) { -pr_info ("Current OPP unknown: Cannot reset voltage\n" ); + uvdc =get_curr_vdd2_voltage (); +if (!uvdc) { +pr_err ("Something wrong.Current voltage not obtained \ +from OPP framework for SR %d!\n" , srid);return 1 ; } - - opp =opp_find_by_opp_id (OPP_L3 , target_opp_no); -if (!opp) -return 1 ; - - uvdc =opp_get_voltage (opp); vsel =omap_twl_uv_to_vsel (uvdc); reg_addr =R_VDD2_SR_CONTROL ;
@@ -452,35 +430,20 @@ static int sr_reset_voltage(int srid)return 0 ; } -static int sr_enable (struct omap_sr *sr,u32 target_opp_no) +static int sr_enable (struct omap_sr *sr,unsigned long volt) {u32 nvalue_reciprocal, v; -struct omap_opp *opp; -struct omap_smartreflex_data *pdata = sr->pdev->dev.platform_data; -int uvdc; +struct omap_volt_data volt_data;char vsel; -if (sr->srid ==SR1 ) { - opp =opp_find_by_opp_id (OPP_MPU , target_opp_no); -if (!opp) -return false; - }else { - opp =opp_find_by_opp_id (OPP_L3 , target_opp_no); -if (!opp) -return false; - } - -if (!pdata->sr_nvalue) { -pr_notice ("N target values does not exist for SR%d\n" , - sr->srid); +if (!sr_match_volt (sr, volt, &volt_data))return false; - } - nvalue_reciprocal = pdata->sr_nvalue[target_opp_no -1 ]; + nvalue_reciprocal = volt_data.sr_nvalue;if (nvalue_reciprocal ==0 ) { -pr_notice ("OPP%d doesn't support SmartReflex\n" , - target_opp_no); +pr_notice ("NVALUE = 0 at voltage %ld for Smartreflex %d\n" , + volt, sr->srid);return false; }
@@ -491,8 +454,7 @@ static int sr_enable(struct omap_sr *sr, u32 target_opp_no) (ERRCONFIG_VPBOUNDINTEN |ERRCONFIG_VPBOUNDINTST ), (ERRCONFIG_VPBOUNDINTEN | ERRCONFIG_VPBOUNDINTST)); - uvdc =opp_get_voltage (opp); - vsel =omap_twl_uv_to_vsel (uvdc); + vsel =omap_twl_uv_to_vsel (volt);if (sr->srid ==SR1 ) {/* set/latch init voltage */
@@ -578,7 +540,7 @@ static void sr_disable(struct omap_sr *sr) } -void sr_start_vddautocomap (int srid,u32 target_opp_no) +void sr_start_vddautocomap (int srid,unsigned long volt) {struct omap_sr *sr =_sr_lookup (srid);
@@ -594,7 +556,7 @@ void sr_start_vddautocomap(int srid, u32 target_opp_no) } sr->is_autocomp_active =1 ; -if (!sr_enable (sr, target_opp_no)) { +if (!sr_enable (sr, volt)) { sr->is_autocomp_active =0 ;if (sr->is_sr_reset ==1 )sr_clk_disable (sr);
@@ -627,7 +589,7 @@ EXPORT_SYMBOL(sr_stop_vddautocomap);void enable_smartreflex (int srid) { -u32 target_opp_no =0 ; +unsigned long curr_volt =0 ;struct omap_sr *sr =_sr_lookup (srid);if (!sr) {
@@ -642,18 +604,18 @@ void enable_smartreflex(int srid)sr_clk_enable (sr);if (srid ==SR1 ) - target_opp_no =get_vdd1_opp (); + curr_volt =get_curr_vdd1_voltage ();else if (srid ==SR2 ) - target_opp_no =get_vdd2_opp (); + curr_volt =get_curr_vdd2_voltage (); -if (!target_opp_no) { -pr_info ("Current OPP unknown \ +if (!curr_volt) { +pr_info ("Current voltage unknown \ Cannot configure SR\n" ); }sr_configure (sr); -if (!sr_enable (sr, target_opp_no)) +if (!sr_enable (sr, curr_volt))sr_clk_disable (sr); } }
@@ -788,10 +750,13 @@ int sr_voltagescale_vcbypass(u32 target_opp, u32 current_opp,udelay (t2_smps_delay);if (sr_status) { +unsigned long volt; + + volt = (target_vsel *12500 ) +600000 ;if (vdd ==VDD1_OPP ) -sr_start_vddautocomap (SR1 , target_opp_no); +sr_start_vddautocomap (SR1 , volt);else if (vdd ==VDD2_OPP ) -sr_start_vddautocomap (SR2 , target_opp_no); +sr_start_vddautocomap (SR2 , volt); }return 0 ;
@@ -824,13 +789,13 @@ static int omap_sr_autocomp_store(void *data, u64 val)if (val ==0 ) {sr_stop_vddautocomap (sr_info->srid); }else { -u32 current_opp; +unsigned long curr_volt;if (sr_info->srid ==SR1 ) - current_opp =get_vdd1_opp (); + curr_volt =get_curr_vdd1_voltage ();else - current_opp =get_vdd2_opp (); -sr_start_vddautocomap (sr_info->srid, current_opp); + curr_volt =get_curr_vdd2_voltage (); +sr_start_vddautocomap (sr_info->srid, curr_volt); }return 0 ; }
@@ -856,12 +821,6 @@ static int __devinit omap_smartreflex_probe(struct platform_device *pdev) sr_info->irq = odev->hwmods[0 ]->mpu_irqs[0 ].irq;sr_set_clk_length (sr_info); -if (sr_info->srid ==SR1 ) { - sr_info->vdd_opp_clk =clk_get (NULL ,"dpll1_ck" ); - }else { - sr_info->vdd_opp_clk =clk_get (NULL ,"l3_ick" ); - } -/* Create the debug fs enteries */ sprintf (name,"sr%d_autocomp" , sr_info->srid); (void) debugfs_create_file(name, S_IRUGO | S_IWUGO, pm_dbg_main_dir,
arch/arm/mach-omap2/smartreflex.h +16 -5
@@ -242,6 +242,17 @@ extern u32 current_vdd2_opp;#endif /** +* omap_volt_data - Omap voltage specific data. +* +* @voltage : The possible voltage value +* @sr_nvalue : Smartreflex N target value at voltage <voltage> +*/ +struct omap_volt_data { +unsigned long voltage; +u32 sr_nvalue; +}; + +/** * omap_smartreflex_dev_data - Smartreflex device specific data * * @volts_supported : Number of distinct voltages possible for the VDD
@@ -295,10 +306,10 @@ struct omap_smartreflex_dev_data {* @device_idle : fn pointer to be pouplated with omap_device idle API */ struct omap_smartreflex_data { -u32 senp_mod; -u32 senn_mod; -u32 *sr_nvalue; -bool enable_on_init; +u32 senp_mod; +u32 senn_mod; +struct omap_volt_data *sr_volt_data; +bool enable_on_init;int (*device_enable)(struct platform_device *pdev);int (*device_shutdown)(struct platform_device *pdev);int (*device_idle)(struct platform_device *pdev);
@@ -307,7 +318,7 @@ struct omap_smartreflex_data {void enable_smartreflex (int srid);void disable_smartreflex (int srid);int sr_voltagescale_vcbypass (u32 t_opp,u32 c_opp,u8 t_vsel,u8 c_vsel); -void sr_start_vddautocomap (int srid,u32 target_opp_no); +void sr_start_vddautocomap (int srid,unsigned long volt);int sr_stop_vddautocomap (int srid);#else static inline void enable_smartreflex (int srid) {}
arch/arm/mach-omap2/sr_device.c +33 -6
@@ -51,8 +51,9 @@ static void __init sr_read_efuse( !dev_data->efuse_nvalues_offs))return ; - sr_data->sr_nvalue =kzalloc (sizeof (sr_data->sr_nvalue) * - dev_data->volts_supported ,GFP_KERNEL ); +if (WARN_ON (!sr_data->sr_volt_data)) +return ; + sr_data->senn_mod = (omap_ctrl_readl (dev_data->efuse_sr_control) & (0x3 << dev_data->sennenable_shift) >> dev_data->sennenable_shift);
@@ -60,7 +61,7 @@ static void __init sr_read_efuse( (0x3 << dev_data->senpenable_shift) >> dev_data->senpenable_shift);for (i =0 ; i < dev_data->volts_supported; i++) - sr_data->sr_nvalue[i] =omap_ctrl_readl ( + sr_data->sr_volt_data[i].sr_nvalue =omap_ctrl_readl ( dev_data->efuse_nvalues_offs[i]); }
@@ -78,12 +79,13 @@ static void __init sr_set_testing_nvalues( !dev_data->test_nvalues))return ; - sr_data->sr_nvalue =kzalloc (sizeof (sr_data->sr_nvalue) * - dev_data->volts_supported ,GFP_KERNEL ); +if (WARN_ON (!sr_data->sr_volt_data)) +return ; + sr_data->senn_mod = dev_data->test_sennenable; sr_data->senp_mod = dev_data->test_senpenable;for (i =0 ; i < dev_data->volts_supported; i++) - sr_data->sr_nvalue[i] = dev_data->test_nvalues[i]; + sr_data->sr_volt_data[i].sr_nvalue = dev_data->test_nvalues[i]; } static void __init sr_set_nvalues(struct omap_smartreflex_dev_data *dev_data,
@@ -97,6 +99,28 @@ static void __init sr_set_nvalues(struct omap_smartreflex_dev_data *dev_data, } } +static void __init omap34xx_sr_volt_details (struct omap_smartreflex_data + *sr_data,int srid, +int volt_count) +{ + sr_data->sr_volt_data =kzalloc (sizeof (sr_data->sr_volt_data) * + volt_count ,GFP_KERNEL ); +if (WARN_ON (!sr_data->sr_volt_data)) +return ; + +if (srid ==SR1 ) { + sr_data->sr_volt_data[0 ].voltage =975000 ; + sr_data->sr_volt_data[1 ].voltage =1075000 ; + sr_data->sr_volt_data[2 ].voltage =1200000 ; + sr_data->sr_volt_data[3 ].voltage =1270000 ; + sr_data->sr_volt_data[4 ].voltage =1350000 ; + }else if (srid ==SR2 ) { + sr_data->sr_volt_data[0 ].voltage =975000 ; + sr_data->sr_volt_data[1 ].voltage =1050000 ; + sr_data->sr_volt_data[2 ].voltage =1150000 ; + } +} +static int __init omap_devinit_smartreflex (void ) {int i =0 ;
@@ -124,6 +148,9 @@ static int __init omap_devinit_smartreflex(void) sr_data->device_enable = omap_device_enable; sr_data->device_shutdown = omap_device_shutdown; sr_data->device_idle = omap_device_idle; +if (cpu_is_omap34xx ()) +omap34xx_sr_volt_details (sr_data, i +1 , + sr_dev_data->volts_supported);sr_set_nvalues (sr_dev_data, sr_data); od = omap_device_build(name, i, oh, sr_data, sizeof(*sr_data),
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 6/22 OMAP3: PM: Correcting API names in samrtreflex driver.
This patch corrects typo in some of the API names in smartreflex driver. It also renames enable_smartreflex, disable_smartreflex APIs to omap_smartreflex_enable and omap_smartreflex_disable to be
more consistent with rest of the API's in the driver code.
--- arch/arm/mach-omap2/pm34xx.c | 8 ++++---- arch/arm/mach-omap2/smartreflex.c | 26 +++++++++++++------------- arch/arm/mach-omap2/smartreflex.h | 12 ++++++------ 3 files changed, 23 insertions(+), 23 deletions(-)
arch/arm/mach-omap2/pm34xx.c +4 -4
@@ -430,9 +430,9 @@ void omap_sram_idle(void)* Only needed if we are going to enter retention or off. */ if (mpu_next_state <=PWRDM_POWER_RET ) -disable_smartreflex (SR1 ); +omap_smartreflex_disable (SR1 );if (core_next_state <=PWRDM_POWER_RET ) -disable_smartreflex (SR2 ); +omap_smartreflex_disable (SR2 );/* CORE */ if (core_next_state <PWRDM_POWER_ON ) {
@@ -531,9 +531,9 @@ void omap_sram_idle(void)* retention or off */ if (mpu_next_state <=PWRDM_POWER_RET ) -enable_smartreflex (SR1 ); +omap_smartreflex_enable (SR1 );if (core_next_state <=PWRDM_POWER_RET ) -enable_smartreflex (SR2 ); +omap_smartreflex_enable (SR2 );/* PER */ if (per_next_state <PWRDM_POWER_ON ) {
arch/arm/mach-omap2/smartreflex.c +13 -13
@@ -540,7 +540,7 @@ static void sr_disable(struct omap_sr *sr) } -void sr_start_vddautocomap (int srid,unsigned long volt) +void sr_start_vddautocomp (int srid,unsigned long volt) {struct omap_sr *sr =_sr_lookup (srid);
@@ -562,9 +562,9 @@ void sr_start_vddautocomap(int srid, unsigned long volt)sr_clk_disable (sr); } } -EXPORT_SYMBOL (sr_start_vddautocomap); +EXPORT_SYMBOL (sr_start_vddautocomp); -int sr_stop_vddautocomap (int srid) +int sr_stop_vddautocomp (int srid) {struct omap_sr *sr =_sr_lookup (srid);
@@ -585,9 +585,9 @@ int sr_stop_vddautocomap(int srid)return false; } -EXPORT_SYMBOL (sr_stop_vddautocomap); +EXPORT_SYMBOL (sr_stop_vddautocomp); -void enable_smartreflex (int srid) +void omap_smartreflex_enable (int srid) {unsigned long curr_volt =0 ;struct omap_sr *sr =_sr_lookup (srid);
@@ -621,7 +621,7 @@ void enable_smartreflex(int srid) } } -void disable_smartreflex (int srid) +void omap_smartreflex_disable (int srid) {u32 i =0 ;struct omap_sr *sr =_sr_lookup (srid);
@@ -696,7 +696,7 @@ int sr_voltagescale_vcbypass(u32 target_opp, u32 current_opp, current_opp_no =get_opp_no (current_opp);if (vdd ==VDD1_OPP ) { - sr_status =sr_stop_vddautocomap (SR1 ); + sr_status =sr_stop_vddautocomp (SR1 ); t2_smps_steps =abs (target_vsel - current_vsel); prm_rmw_mod_reg_bits(OMAP3430_VC_CMD_ON_MASK,
@@ -706,7 +706,7 @@ int sr_voltagescale_vcbypass(u32 target_opp, u32 current_opp, reg_addr =R_VDD1_SR_CONTROL ; }else if (vdd ==VDD2_OPP ) { - sr_status =sr_stop_vddautocomap (SR2 ); + sr_status =sr_stop_vddautocomp (SR2 ); t2_smps_steps =abs (target_vsel - current_vsel); prm_rmw_mod_reg_bits(OMAP3430_VC_CMD_ON_MASK,
@@ -754,9 +754,9 @@ int sr_voltagescale_vcbypass(u32 target_opp, u32 current_opp, volt = (target_vsel *12500 ) +600000 ;if (vdd ==VDD1_OPP ) -sr_start_vddautocomap (SR1 , volt); +sr_start_vddautocomp (SR1 , volt);else if (vdd ==VDD2_OPP ) -sr_start_vddautocomap (SR2 , volt); +sr_start_vddautocomp (SR2 , volt); }return 0 ;
@@ -787,7 +787,7 @@ static int omap_sr_autocomp_store(void *data, u64 val)return 0 ; }if (val ==0 ) { -sr_stop_vddautocomap (sr_info->srid); +sr_stop_vddautocomp (sr_info->srid); }else {unsigned long curr_volt;
@@ -795,7 +795,7 @@ static int omap_sr_autocomp_store(void *data, u64 val) curr_volt =get_curr_vdd1_voltage (); else curr_volt =get_curr_vdd2_voltage (); -sr_start_vddautocomap (sr_info->srid, curr_volt); +sr_start_vddautocomp (sr_info->srid, curr_volt); }return 0 ; }
@@ -840,7 +840,7 @@ static int __devexit omap_smartreflex_remove(struct platform_device *pdev)/* Disable Autocompensation if enabled before removing the module */ if (sr_info->is_autocomp_active ==1 ) -sr_stop_vddautocomap (sr_info->srid); +sr_stop_vddautocomp (sr_info->srid);list_del (&sr_info->node);kfree (sr_info);
arch/arm/mach-omap2/smartreflex.h +6 -6
@@ -315,14 +315,14 @@ struct omap_smartreflex_data {int (*device_idle)(struct platform_device *pdev); }; -void enable_smartreflex (int srid); -void disable_smartreflex (int srid); +void omap_smartreflex_enable (int srid); +void omap_smartreflex_disable (int srid);int sr_voltagescale_vcbypass (u32 t_opp,u32 c_opp,u8 t_vsel,u8 c_vsel); -void sr_start_vddautocomap (int srid,unsigned long volt); -int sr_stop_vddautocomap (int srid); +void sr_start_vddautocomp (int srid,unsigned long volt); +int sr_stop_vddautocomp (int srid);#else -static inline void enable_smartreflex (int srid) {} -static inline void disable_smartreflex (int srid) {} +static inline void omap_smartreflex_enable (int srid) {} +static inline void omap_smartreflex_disable (int srid) {}#endif #endif
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 7/22 OMAP3: PM: Smartreflex class related changes for smartreflex.c
OMAP3 smartreflex modules are capable of two different classes of implementaion -
Class-2: Continuous Software Calibration
Class-3: Continuous Hardware Calibration.
OMAP3 along with T2/Gaia supports the Class 3 implementaion. With a different PMIC it can support Class 2 implementaion also.
The idea behind this patch is that smartreflex.c should be able to support both the classes of Smartreflex and the class specific details for smartreflex should stay out of this file in a separate class file.
This patch introduces smartreflex class specific hooks in smartreflex.c. This patch only takes care of smartreflex enable disable hooks which differ between Class 2 and Class 3. There are some register setting changes between both the classes which will be taken care of in a later patch.
This will form the base for adding class specific drivers in later patches.
--- arch/arm/mach-omap2/smartreflex.c | 259 ++++++++++++++++++++---------------- arch/arm/mach-omap2/smartreflex.h | 44 ++++++- 2 files changed, 181 insertions(+), 122 deletions(-)
arch/arm/mach-omap2/smartreflex.c +144 -115
@@ -56,6 +56,7 @@ struct omap_sr {/* sr_list contains all the instances of smartreflex module */ static LIST_HEAD (sr_list); +static struct omap_smartreflex_class_data *sr_class;static inline void sr_write_reg (struct omap_sr *sr,unsigned offset,u32 value) {
@@ -430,12 +431,84 @@ static int sr_reset_voltage(int srid)return 0 ; } -static int sr_enable (struct omap_sr *sr,unsigned long volt) +static void sr_start_vddautocomp (int srid) +{ +struct omap_sr *sr =_sr_lookup (srid); + +if (!sr) { +pr_warning ("omap_sr struct corresponding to SR%d not found\n" , + srid); +return ; + } + +if (!sr_class || !(sr_class->enable)) { +pr_warning ("smartreflex class driver not registered\n" ); +return ; + } + +if (sr->is_sr_reset ==1 ) { +sr_clk_enable (sr); +sr_configure (sr); + } + + sr->is_autocomp_active =1 ; +if (!sr_class->enable (srid)) { + sr->is_autocomp_active =0 ; +if (sr->is_sr_reset ==1 ) +sr_clk_disable (sr); + } +} + +static void sr_stop_vddautocomp (int srid) +{ +struct omap_sr *sr =_sr_lookup (srid); + +if (!sr) { +pr_warning ("omap_sr struct corresponding to SR%d not found\n" , + srid); +return ; + } + +if (!sr_class || !(sr_class->disable)) { +pr_warning ("smartreflex class driver not registered\n" ); +return ; + } + +if (sr->is_autocomp_active ==1 ) { + sr_class->disable (srid); +sr_clk_disable (sr); + sr->is_autocomp_active =0 ; +/* Reset the volatage for current OPP */ +sr_reset_voltage (srid); + } +} + +/* Public Functions */ + +/** +* sr_enable : Enables the smartreflex module. +* @srid - The id of the sr module to be enabled. +* @volt - The voltage at which the Voltage domain associated with +* the smartreflex module is operating at. This is required only to program +* the correct Ntarget value. +* +* This API is to be called from the smartreflex class driver to +* enable a smartreflex module. Returns true on success.Returns false if the +* target opp id passed is wrong or if ntarget value is wrong. +*/ +int sr_enable (int srid,unsigned long volt) {u32 nvalue_reciprocal, v;struct omap_volt_data volt_data; +struct omap_sr *sr =_sr_lookup (srid);char vsel; +if (!sr) { +pr_warning ("omap_sr struct corresponding to SR%d not found\n" , + srid); +return false; + } +if (!sr_match_volt (sr, volt, &volt_data))return false;
@@ -498,10 +571,24 @@ static int sr_enable(struct omap_sr *sr, unsigned long volt)return true; } -static void sr_disable (struct omap_sr *sr) +/** +* sr_disable : Disables the smartreflex module. +* @srid - The id of the sr module to be disabled. +* +* This API is to be called from the smartreflex class driver to +* disable a smartreflex module. +*/ +void sr_disable (int srid) { +struct omap_sr *sr =_sr_lookup (srid);u32 i =0 ; +if (!sr) { +pr_warning ("omap_sr struct corresponding to SR%d not found\n" , + srid); +return ; + } + sr->is_sr_reset =1 ;/* SRCONFIG - disable SR */
@@ -539,8 +626,17 @@ static void sr_disable(struct omap_sr *sr) } } - -void sr_start_vddautocomp (int srid,unsigned long volt) +/** +* omap_smartreflex_enable : API to enable SR clocks and to call into the +* registered smartreflex class enable API. +* @srid - The id of the sr module to be enabled. +* +* This API is to be called from the kernel in order to enable +* a particular smartreflex module. This API will do the initial +* configurations to turn on the smartreflex module and in turn call +* into the registered smartreflex class enable API. +*/ +void omap_smartreflex_enable (int srid) {struct omap_sr *sr =_sr_lookup (srid);
@@ -550,51 +646,8 @@ void sr_start_vddautocomp(int srid, unsigned long volt)return ; } -if (sr->is_sr_reset ==1 ) { -sr_clk_enable (sr); -sr_configure (sr); - } - - sr->is_autocomp_active =1 ; -if (!sr_enable (sr, volt)) { - sr->is_autocomp_active =0 ; -if (sr->is_sr_reset ==1 ) -sr_clk_disable (sr); - } -} -EXPORT_SYMBOL (sr_start_vddautocomp); - -int sr_stop_vddautocomp (int srid) -{ -struct omap_sr *sr =_sr_lookup (srid); - -if (!sr) { -pr_warning ("omap_sr struct corresponding to SR%d not found\n" , - srid); -return false; - } - -if (sr->is_autocomp_active ==1 ) { -sr_disable (sr); -sr_clk_disable (sr); - sr->is_autocomp_active =0 ; -/* Reset the volatage for current OPP */ -sr_reset_voltage (srid); -return true; - }else -return false; - -} -EXPORT_SYMBOL (sr_stop_vddautocomp); - -void omap_smartreflex_enable (int srid) -{ -unsigned long curr_volt =0 ; -struct omap_sr *sr =_sr_lookup (srid); - -if (!sr) { -pr_warning ("omap_sr struct corresponding to SR%d not found\n" , - srid); +if (!sr_class || !(sr_class->enable)) { +pr_warning ("smartreflex class driver not registered\n" );return ; }
@@ -602,28 +655,24 @@ void omap_smartreflex_enable(int srid)if (sr->is_sr_reset ==1 ) {/* Enable SR clks */ sr_clk_enable (sr); - -if (srid ==SR1 ) - curr_volt =get_curr_vdd1_voltage (); -else if (srid ==SR2 ) - curr_volt =get_curr_vdd2_voltage (); - -if (!curr_volt) { -pr_info ("Current voltage unknown \ -Cannot configure SR\n" ); - } -sr_configure (sr); - -if (!sr_enable (sr, curr_volt)) +if (!sr_class->enable (srid))sr_clk_disable (sr); } } } +/** +* omap_smartreflex_disable : API to disable SR clocks and to call into the +* registered smartreflex class disable API. +* @srid - The id of the sr module to be disabled. +* +* This API is to be called from the kernel in order to disable +* a particular smartreflex module. This API will in turn call +* into the registered smartreflex class disable API. +*/ void omap_smartreflex_disable (int srid) { -u32 i =0 ;struct omap_sr *sr =_sr_lookup (srid);if (!sr) {
@@ -632,53 +681,43 @@ void omap_smartreflex_disable(int srid)return ; } +if (!sr_class || !(sr_class->disable)) { +pr_warning ("smartreflex class driver not registered\n" ); +return ; + } +if (sr->is_autocomp_active ==1 ) {if (sr->is_sr_reset ==0 ) { - - sr->is_sr_reset =1 ; -/* SRCONFIG - disable SR */ -sr_modify_reg (sr,SRCONFIG ,SRCONFIG_SRENABLE , - ~SRCONFIG_SRENABLE ); - + sr_class->disable (srid);/* Disable SR clk */ sr_clk_disable (sr); -if (sr->srid ==SR1 ) { -/* Wait for VP idle before disabling VP */ -while ((!prm_read_mod_reg (OMAP3430_GR_MOD , -OMAP3_PRM_VP1_STATUS_OFFSET )) - && i++ <MAX_TRIES ) -udelay (1 ); - -if (i >=MAX_TRIES ) -pr_warning ("VP1 not idle, still going \ -ahead with VP1 disable\n" ); - -/* Disable VP1 */ -prm_clear_mod_reg_bits (PRM_VP1_CONFIG_VPENABLE , -OMAP3430_GR_MOD , -OMAP3_PRM_VP1_CONFIG_OFFSET ); - }else if (sr->srid ==SR2 ) { -/* Wait for VP idle before disabling VP */ -while ((!prm_read_mod_reg (OMAP3430_GR_MOD , -OMAP3_PRM_VP2_STATUS_OFFSET )) - && i++ <MAX_TRIES ) -udelay (1 ); - -if (i >=MAX_TRIES ) -pr_warning ("VP2 not idle, still going \ -ahead with VP2 disable\n" ); - -/* Disable VP2 */ -prm_clear_mod_reg_bits (PRM_VP2_CONFIG_VPENABLE , -OMAP3430_GR_MOD , -OMAP3_PRM_VP2_CONFIG_OFFSET ); - }/* Reset the volatage for current OPP */ sr_reset_voltage (srid); } } } +/** +* omap_sr_register_class : API to register a smartreflex class parameters. +* @class_data - The structure containing various sr class specific data. +* +* This API is to be called by the smartreflex class driver to register itself +* with the smartreflex driver during init. +*/ +void omap_sr_register_class (struct omap_smartreflex_class_data *class_data) +{ +if (!class_data) { +pr_warning ("Smartreflex class data passed is NULL\n" ); +return ; + } + +if (sr_class) { +pr_warning ("Smartreflex class driver already registered\n" ); +return ; + } + sr_class = class_data; +} +/* Voltage Scaling using SR VCBYPASS */ int sr_voltagescale_vcbypass (u32 target_opp,u32 current_opp,u8 target_vsel,u8 current_vsel)
@@ -750,13 +789,10 @@ int sr_voltagescale_vcbypass(u32 target_opp, u32 current_opp,udelay (t2_smps_delay);if (sr_status) { -unsigned long volt; - - volt = (target_vsel *12500 ) +600000 ;if (vdd ==VDD1_OPP ) -sr_start_vddautocomp (SR1 , volt); +sr_start_vddautocomp (SR1 );else if (vdd ==VDD2_OPP ) -sr_start_vddautocomp (SR2 , volt); +sr_start_vddautocomp (SR2 ); }return 0 ;
@@ -786,17 +822,10 @@ static int omap_sr_autocomp_store(void *data, u64 val) sr_info->srid);return 0 ; } -if (val ==0 ) { +if (val ==0 )sr_stop_vddautocomp (sr_info->srid); - }else { -unsigned long curr_volt; - -if (sr_info->srid ==SR1 ) - curr_volt =get_curr_vdd1_voltage (); -else - curr_volt =get_curr_vdd2_voltage (); -sr_start_vddautocomp (sr_info->srid, curr_volt); - } +else +sr_start_vddautocomp (sr_info->srid);return 0 ; }
arch/arm/mach-omap2/smartreflex.h +37 -7
61 lines not on this page · raw message
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 8/22 OMAP3: PM: Adding smartreflex class 3 driver.
This patch adds smartreflex class 3 driver. This driver hooks up with the generic smartreflex driver smartreflex.c to abstract out class specific implementations out of the generic driver.
--- arch/arm/mach-omap2/Makefile | 1 + arch/arm/mach-omap2/board-3430sdp.c | 2 + arch/arm/mach-omap2/smartreflex-class3.c | 48 ++++++++++++++++++++++++++++++ arch/arm/mach-omap2/smartreflex-class3.h | 18 +++++++++++ arch/arm/plat-omap/Kconfig | 11 ++++++- 5 files changed, 79 insertions(+), 1 deletions(-) create mode 100644 arch/arm/mach-omap2/smartreflex-class3.c create mode 100644 arch/arm/mach-omap2/smartreflex-class3.h
arch/arm/mach-omap2/Makefile +1 -0
@@ -49,6 +49,7 @@ obj-$(CONFIG_ARCH_OMAP2) += sleep24xx.o obj-$(CONFIG_ARCH_OMAP3) += pm34xx.o sleep34xx.o cpuidle34xx.o obj-$(CONFIG_PM_DEBUG) += pm-debug.o obj-$(CONFIG_OMAP_SMARTREFLEX) += sr_device.o smartreflex.o +obj-$(CONFIG_OMAP_SMARTREFLEX_CLASS3) += smartreflex-class3.o AFLAGS_sleep24xx.o :=-Wa,-march=armv6 AFLAGS_sleep34xx.o :=-Wa,-march=armv7-a
arch/arm/mach-omap2/board-3430sdp.c +2 -0
@@ -50,6 +50,7 @@#include "hsmmc.h" #include "pm.h" #include "omap3-opp.h" +#include "smartreflex-class3.h" #define SDP3430_TS_GPIO_IRQ_SDPV1 3#define SDP3430_TS_GPIO_IRQ_SDPV2 2
@@ -913,6 +914,7 @@ static void __init omap_3430sdp_init(void)sdp3430_display_init ();enable_board_wakeup_source ();usb_ehci_init (&ehci_pdata); +sr_class3_init (); }static void __init omap_3430sdp_map_io (void )
arch/arm/mach-omap2/smartreflex-class3.c new file +48 -0
48 lines not on this page · raw message
arch/arm/mach-omap2/smartreflex-class3.h new file +18 -0
@@ -0,0 +1,18 @@ +/* +* Smartreflex Class 3 Routines +* +* Author: Thara Gopinath <[email protected]> +* +* Copyright (C) 2010 Texas Instruments, Inc. +* Thara Gopinath <[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +*/ + +#ifdef CONFIG_OMAP_SMARTREFLEX_CLASS3 +int sr_class3_init (void ); +#else +static int sr_class3_init (void ) {} +#endif
arch/arm/plat-omap/Kconfig +10 -1
@@ -55,7 +55,7 @@ config OMAP_DEBUG_LEDS config OMAP_SMARTREFLEX bool "SmartReflex support" - depends on ARCH_OMAP3 && TWL4030_CORE && PM + depends on ARCH_OMAP3 && PM help Say Y if you want to enable SmartReflex.
@@ -70,6 +70,15 @@ config OMAP_SMARTREFLEX compensation for VDD1 and VDD2, user must write 1 to /sys/power/sr_vddX_autocomp, where X is 1 or 2. +config OMAP_SMARTREFLEX_CLASS3 + bool "Class 3 mode of Smartreflex Implementation" + depends on OMAP_SMARTREFLEX && TWL4030_CORE + help + Say Y to enable Class 3 implementation of Smartreflex + + Class 3 implementation of Smartreflex employs continuous hardware + voltage caliberation. + config OMAP_SMARTREFLEX_TESTING bool "Smartreflex testing support" depends on OMAP_SMARTREFLEX
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 9/22 OMAP3: PM: Creating separate files for handling OMAP3 voltage related operations.
This patch creates voltage.c and voltage.h files and moves all voltage processor and voltage controller specific code from smartreflex.c and other places in the OMAP3 codebase into these two files.
This along with smartreflex class driver addition will make smartreflex.c a generic driver to support both Class 2 and Class 3 smartreflex implementaions.
--- arch/arm/mach-omap2/Makefile | 3 +- arch/arm/mach-omap2/board-3430sdp.c | 3 +- arch/arm/mach-omap2/pm.h | 7 - arch/arm/mach-omap2/pm34xx.c | 87 +---- arch/arm/mach-omap2/smartreflex-class3.c | 4 + arch/arm/mach-omap2/smartreflex.c | 378 +------------------ arch/arm/mach-omap2/smartreflex.h | 137 ------- arch/arm/mach-omap2/voltage.c | 626 ++++++++++++++++++++++++++++++ arch/arm/mach-omap2/voltage.h | 74 ++++ 9 files changed, 712 insertions(+), 607 deletions(-) create mode 100644 arch/arm/mach-omap2/voltage.c create mode 100644 arch/arm/mach-omap2/voltage.h
arch/arm/mach-omap2/Makefile +2 -1
@@ -46,7 +46,8 @@ obj-$(CONFIG_ARCH_OMAP2) += sdrc2xxx.o ifeq ($(CONFIG_PM),y) obj-$(CONFIG_ARCH_OMAP2) += pm24xx.o obj-$(CONFIG_ARCH_OMAP2) += sleep24xx.o -obj-$(CONFIG_ARCH_OMAP3) += pm34xx.o sleep34xx.o cpuidle34xx.o +obj-$(CONFIG_ARCH_OMAP3) += pm34xx.o sleep34xx.o cpuidle34xx.o \ + voltage.o obj-$(CONFIG_PM_DEBUG) += pm-debug.o obj-$(CONFIG_OMAP_SMARTREFLEX) += sr_device.o smartreflex.o obj-$(CONFIG_OMAP_SMARTREFLEX_CLASS3) += smartreflex-class3.o
arch/arm/mach-omap2/board-3430sdp.c +2 -1
@@ -49,6 +49,7 @@#include "sdram-qimonda-hyb18m512160af-6.h" #include "hsmmc.h" #include "pm.h" +#include "voltage.h" #include "omap3-opp.h" #include "smartreflex-class3.h"
@@ -347,7 +348,7 @@ static void __init omap_3430sdp_init_irq(void) omap_board_config_size =ARRAY_SIZE (sdp3430_config);omap3_pm_init_opp_table ();omap3_pm_init_cpuidle (omap3_cpuidle_params_table); -omap3_pm_init_vc (&omap3_setuptime_table); +omap_voltage_init_vc (&omap3_setuptime_table);omap2_init_common_hw (hyb18m512160af6_sdrc_params,NULL );omap_init_irq ();omap_gpio_init ();
arch/arm/mach-omap2/pm.h +0 -7
@@ -57,13 +57,6 @@ struct prm_setup_vc {u16 vdd1_ret;u16 vdd1_off; }; -#ifdef CONFIG_PM -extern void omap3_pm_init_vc (struct prm_setup_vc *setup_vc); -#else -static inline void omap3_pm_init_vc (struct prm_setup_vc *setup_vc) -{ -} -#endif extern int omap3_pm_get_suspend_state (struct powerdomain *pwrdm);extern int omap3_pm_set_suspend_state (struct powerdomain *pwrdm,int state);
arch/arm/mach-omap2/pm34xx.c +3 -84
115 lines not on this page · raw message
arch/arm/mach-omap2/smartreflex-class3.c +4 -0
@@ -11,6 +11,7 @@#include "smartreflex.h" #include "smartreflex-class3.h" +#include "voltage.h" static int sr_class3_enable (int id) {
@@ -25,12 +26,15 @@ static int sr_class3_enable(int id)return false; } +omap_voltageprocessor_enable (id);return sr_enable (id, volt); }static int sr_class3_disable (int id) { +omap_voltageprocessor_disable (id);sr_disable (id); +omap_reset_voltage (id);return true; }
arch/arm/mach-omap2/smartreflex.c +1 -377
469 lines not on this page · raw message
arch/arm/mach-omap2/smartreflex.h +0 -137
180 lines not on this page · raw message
arch/arm/mach-omap2/voltage.c new file +626 -0
626 lines not on this page · raw message
arch/arm/mach-omap2/voltage.h new file +74 -0
74 lines not on this page · raw message
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 10/22 OMAP3: PM: Adding voltage table support in voltage driver.
This patch introduces the framework to create voltage table per VDD basis in voltage driver. Each VDD will have one voltage table, which in turn will contain one entry per voltage supported and other data associated with the voltage like smartreflex N-target values. This patch also generates voltage tables for VDD1 and VDD2 of OMAP3430 and passes them as dev_attr to sr_device.c in order to populate the smartreflex n-target values.
These voltage tables are extended in a later patch to contain more voltage specific information like errminlimt and errorgain values.
--- arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 7 +- arch/arm/mach-omap2/smartreflex.c | 27 +-------- arch/arm/mach-omap2/smartreflex.h | 13 +---- arch/arm/mach-omap2/sr_device.c | 42 ++---------- arch/arm/mach-omap2/voltage.c | 93 +++++++++++++++++++++++++++- arch/arm/mach-omap2/voltage.h | 15 +++++ 6 files changed, 118 insertions(+), 79 deletions(-)
arch/arm/mach-omap2/omap_hwmod_3xxx_data.c +3 -4
@@ -23,6 +23,7 @@#include "prm-regbits-34xx.h" #include "smartreflex.h" +#include "voltage.h" /* * OMAP3xxx hardware module integration data
@@ -240,14 +241,13 @@ static u32 omap34xx_sr1_test_nvalues[] = { };static struct omap_smartreflex_dev_data omap34xx_sr1_dev_attr = { - .volts_supported =5 , .efuse_sr_control =OMAP343X_CONTROL_FUSE_SR , .sennenable_shift =OMAP343X_SR1_SENNENABLE_SHIFT , .senpenable_shift =OMAP343X_SR1_SENPENABLE_SHIFT , .efuse_nvalues_offs = omap34xx_sr1_efuse_offs, .test_sennenable =0x3 , .test_senpenable =0x3 , - .test_nvalues = omap34xx_sr1_test_nvalues + .test_nvalues = omap34xx_sr1_test_nvalues, };static struct omap_hwmod omap34xx_sr1_hwmod = {
@@ -276,14 +276,13 @@ static u32 omap34xx_sr2_test_nvalues[] = { };static struct omap_smartreflex_dev_data omap34xx_sr2_dev_attr = { - .volts_supported =3 , .efuse_sr_control =OMAP343X_CONTROL_FUSE_SR , .sennenable_shift =OMAP343X_SR2_SENNENABLE_SHIFT , .senpenable_shift =OMAP343X_SR2_SENPENABLE_SHIFT , .efuse_nvalues_offs = omap34xx_sr2_efuse_offs, .test_sennenable =0x3 , .test_senpenable =0x3 , - .test_nvalues = omap34xx_sr2_test_nvalues + .test_nvalues = omap34xx_sr2_test_nvalues, };static struct omap_hwmod omap34xx_sr2_hwmod = {
arch/arm/mach-omap2/smartreflex.c +2 -25
@@ -31,6 +31,7 @@#include <plat/omap_hwmod.h> #include <plat/omap_device.h> +#include "voltage.h" #include "smartreflex.h" #define SMARTREFLEX_NAME_LEN 16
@@ -110,30 +111,6 @@ static void sr_clk_disable(struct omap_sr *sr) sr->is_sr_reset =1 ; } -static int sr_match_volt (struct omap_sr *sr,unsigned long volt, -struct omap_volt_data *volt_data) -{ -struct omap_smartreflex_data *pdata = sr->pdev->dev.platform_data; -struct omap_device *odev =to_omap_device (sr->pdev); -struct omap_smartreflex_dev_data *sr_dev_data = - odev->hwmods[0 ]->dev_attr; -int i; - -if (!pdata->sr_volt_data) { -pr_notice ("voltage table does not exist for SR %d\n" , sr->srid); -return false; - } -for (i =0 ; i < sr_dev_data->volts_supported; i++) { -if (pdata->sr_volt_data[i].voltage == volt) { - *volt_data = pdata->sr_volt_data[i]; -return true; - } - } -pr_notice ("Unable to match the current voltage with \ -the voltage table for SR %d\n" , sr->srid); -return false; -} -static void sr_set_clk_length (struct omap_sr *sr) {struct clk *sys_ck;
@@ -288,7 +265,7 @@ int sr_enable(int srid, unsigned long volt)return false; } -if (!sr_match_volt (sr, volt, &volt_data)) +if (omap_match_volt (sr->srid, volt, &volt_data))return false; nvalue_reciprocal = volt_data.sr_nvalue;
arch/arm/mach-omap2/smartreflex.h +1 -12
@@ -107,17 +107,6 @@ extern struct dentry *pm_dbg_main_dir;#endif /** -* omap_volt_data - Omap voltage specific data. -* -* @voltage : The possible voltage value -* @sr_nvalue : Smartreflex N target value at voltage <voltage> -*/ -struct omap_volt_data { -unsigned long voltage; -u32 sr_nvalue; -}; - -/** * omap_smartreflex_dev_data - Smartreflex device specific data * * @volts_supported : Number of distinct voltages possible for the VDD
@@ -148,6 +137,7 @@ struct omap_smartreflex_dev_data {u32 test_sennenable;u32 test_senpenable;u32 *test_nvalues; +struct omap_volt_data *volt_data; };#ifdef CONFIG_OMAP_SMARTREFLEX
@@ -188,7 +178,6 @@ struct omap_smartreflex_class_data {struct omap_smartreflex_data {u32 senp_mod;u32 senn_mod; -struct omap_volt_data *sr_volt_data;bool enable_on_init;int (*device_enable)(struct platform_device *pdev);int (*device_shutdown)(struct platform_device *pdev);
arch/arm/mach-omap2/sr_device.c +7 -35
86 lines not on this page · raw message
arch/arm/mach-omap2/voltage.c +90 -3
125 lines not on this page · raw message
arch/arm/mach-omap2/voltage.h +15 -0
@@ -63,6 +63,17 @@/* TODO OMAP4 VP register values if the same file is used for OMAP4*/ +/** +* omap_volt_data - Omap voltage specific data. +* +* @voltage : The possible voltage value +* @sr_nvalue : Smartreflex N target value at voltage <voltage> +*/ +struct omap_volt_data { +unsigned long voltage; +u32 sr_nvalue; +}; +void omap_voltageprocessor_enable (int vp_id);void omap_voltageprocessor_disable (int vp_id);void omap_voltage_init_vc (struct prm_setup_vc *setup_vc);
@@ -70,5 +81,9 @@ void omap_voltage_init(void);int omap_voltage_scale (int vdd,unsigned long target_volt,unsigned long current_volt);void omap_reset_voltage (int vdd); +void omap_get_voltage_table (int vdd,struct omap_volt_data **volt_data, +int *volt_count); +int omap_match_volt (int vdd,unsigned long volt, +struct omap_volt_data *volt_data);unsigned long get_curr_vdd1_voltage (void );unsigned long get_curr_vdd2_voltage (void );
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 11/22 OMAP3: PM: Removing VP1, VP2, SR1 and SR2 defintions.
This patch removes VP1, VP2, SR1 and SR2 macros and replaces them with VDD1 and VDD2 macros.
--- arch/arm/mach-omap2/pm34xx.c | 8 +++--- arch/arm/mach-omap2/smartreflex-class3.c | 4 +- arch/arm/mach-omap2/smartreflex.c | 26 +++++++++++----------- arch/arm/mach-omap2/smartreflex.h | 4 --- arch/arm/mach-omap2/voltage.c | 35 +++++++++++++++-------------- arch/arm/mach-omap2/voltage.h | 6 ++-- 6 files changed, 40 insertions(+), 43 deletions(-)
arch/arm/mach-omap2/pm34xx.c +4 -4
@@ -415,9 +415,9 @@ void omap_sram_idle(void)* Only needed if we are going to enter retention or off. */ if (mpu_next_state <=PWRDM_POWER_RET ) -omap_smartreflex_disable (SR1 ); +omap_smartreflex_disable (VDD1 );if (core_next_state <=PWRDM_POWER_RET ) -omap_smartreflex_disable (SR2 ); +omap_smartreflex_disable (VDD2 );/* CORE */ if (core_next_state <PWRDM_POWER_ON ) {
@@ -516,9 +516,9 @@ void omap_sram_idle(void)* retention or off */ if (mpu_next_state <=PWRDM_POWER_RET ) -omap_smartreflex_enable (SR1 ); +omap_smartreflex_enable (VDD1 );if (core_next_state <=PWRDM_POWER_RET ) -omap_smartreflex_enable (SR2 ); +omap_smartreflex_enable (VDD2 );/* PER */ if (per_next_state <PWRDM_POWER_ON ) {
arch/arm/mach-omap2/smartreflex-class3.c +2 -2
@@ -17,9 +17,9 @@ static int sr_class3_enable(int id) {unsigned long volt =0 ; -if (id ==SR1 ) +if (id ==VDD1 ) volt =get_curr_vdd1_voltage (); -else if (id ==SR2 ) +else if (id ==VDD2 ) volt =get_curr_vdd2_voltage ();if (!volt) {pr_warning ("Current voltage unknown.Cannot enable SR%d\n" , id);
arch/arm/mach-omap2/smartreflex.c +13 -13
@@ -153,7 +153,7 @@ static void sr_configure(struct omap_sr *sr) senp_en = pdata->senp_mod; senn_en = pdata->senn_mod; -if (sr->srid ==SR1 ) { +if (sr->srid ==VDD1 ) { sr_config =SR1_SRCONFIG_ACCUMDATA | (sr->clk_length <<SRCONFIG_SRCLKLENGTH_SHIFT ) | SRCONFIG_SENENABLE | SRCONFIG_ERRGEN_EN |
@@ -170,7 +170,7 @@ static void sr_configure(struct omap_sr *sr) SR_ERRMAXLIMIT_MASK | SR_ERRMINLIMIT_MASK), (SR1_ERRWEIGHT | SR1_ERRMAXLIMIT | SR1_ERRMINLIMIT)); - }else if (sr->srid ==SR2 ) { + }else if (sr->srid ==VDD2 ) { sr_config =SR2_SRCONFIG_ACCUMDATA | (sr->clk_length <<SRCONFIG_SRCLKLENGTH_SHIFT ) | SRCONFIG_SENENABLE | SRCONFIG_ERRGEN_EN |
@@ -196,7 +196,7 @@ static void sr_start_vddautocomp(int srid)if (!sr) {pr_warning ("omap_sr struct corresponding to SR%d not found\n" , - srid); + srid +1 );return ; }
@@ -224,7 +224,7 @@ static void sr_stop_vddautocomp(int srid)if (!sr) {pr_warning ("omap_sr struct corresponding to SR%d not found\n" , - srid); + srid +1 );return ; }
@@ -261,7 +261,7 @@ int sr_enable(int srid, unsigned long volt)if (!sr) {pr_warning ("omap_sr struct corresponding to SR%d not found\n" , - srid); + srid +1 );return false; }
@@ -272,7 +272,7 @@ int sr_enable(int srid, unsigned long volt)if (nvalue_reciprocal ==0 ) {pr_notice ("NVALUE = 0 at voltage %ld for Smartreflex %d\n" , - volt, sr->srid); + volt, sr->srid +1 );return false; }
@@ -301,7 +301,7 @@ void sr_disable(int srid)if (!sr) {pr_warning ("omap_sr struct corresponding to SR%d not found\n" , - srid); + srid +1 );return ; }
@@ -327,7 +327,7 @@ void omap_smartreflex_enable(int srid)if (!sr) {pr_warning ("omap_sr struct corresponding to SR%d not found\n" , - srid); + srid +1 );return ; }
@@ -362,7 +362,7 @@ void omap_smartreflex_disable(int srid)if (!sr) {pr_warning ("omap_sr struct corresponding to SR%d not found\n" , - srid); + srid +1 );return ; }
@@ -409,7 +409,7 @@ static int omap_sr_autocomp_show(void *data, u64 *val)if (!sr_info) {pr_warning ("omap_sr struct corresponding to SR%d not found\n" , - sr_info->srid); + sr_info->srid +1 );return 0 ; } *val = sr_info->is_autocomp_active;
@@ -422,7 +422,7 @@ static int omap_sr_autocomp_store(void *data, u64 val)if (!sr_info) {pr_warning ("omap_sr struct corresponding to SR%d not found\n" , - sr_info->srid); + sr_info->srid +1 );return 0 ; }if (val ==0 )
@@ -445,7 +445,7 @@ static int __devinit omap_smartreflex_probe(struct platform_device *pdev)if (WARN_ON (!sr_info))return -ENOMEM ; sr_info->pdev = pdev; - sr_info->srid = pdev->id +1 ; + sr_info->srid = pdev->id; sr_info->is_sr_reset =1 , sr_info->is_autocomp_active =0 ; sr_info->clk_length =0 ;
@@ -454,7 +454,7 @@ static int __devinit omap_smartreflex_probe(struct platform_device *pdev)sr_set_clk_length (sr_info);/* Create the debug fs enteries */ -sprintf (name,"sr%d_autocomp" , sr_info->srid); +sprintf (name,"sr%d_autocomp" , sr_info->srid +1 ); (void )debugfs_create_file (name,S_IRUGO |S_IWUGO , pm_dbg_main_dir, (void *)sr_info, &pm_sr_fops);
arch/arm/mach-omap2/smartreflex.h +0 -4
@@ -32,10 +32,6 @@ extern struct dentry *pm_dbg_main_dir;#define SENERROR 0x20#define ERRCONFIG 0x24 -/* SR Modules */ -#define SR1 1 -#define SR2 2 -#define GAIN_MAXLIMIT 16#define R_MAXLIMIT 256
arch/arm/mach-omap2/voltage.c +18 -17
@@ -246,11 +246,11 @@ static void vp_latch_vsel(int vp_id)char vsel;/* Should remove this once OPP framework is fixed */ -if (vp_id ==VP1 ) { +if (vp_id ==VDD1 ) { uvdc =get_curr_vdd1_voltage ();if (!uvdc)return ; - }else if (vp_id ==VP2 ) { + }else if (vp_id ==VDD2 ) { uvdc =get_curr_vdd2_voltage ();if (!uvdc)return ;
@@ -310,7 +310,7 @@ static void __init vp_data_configure(int vp_id) {if (cpu_is_omap34xx ()) { vp_reg[vp_id].vp_offs = omap3_vp_offs[vp_id]; -if (vp_id ==VP1 ) { +if (vp_id ==VDD1 ) { vp_reg[vp_id].volt_data = omap34xx_vdd1_volt_data; vp_reg[vp_id].volt_data_count =ARRAY_SIZE (omap34xx_vdd1_volt_data);
@@ -318,7 +318,7 @@ static void __init vp_data_configure(int vp_id) OMAP3430_VDDMIN_SHIFT); vp_reg[vp_id].vp_vddmax = (OMAP3_VP1_VLIMITTO_VDDMAX <<OMAP3430_VDDMAX_SHIFT ); - }else if (vp_id ==VP2 ) { + }else if (vp_id ==VDD2 ) { vp_reg[vp_id].volt_data = omap34xx_vdd2_volt_data; vp_reg[vp_id].volt_data_count =ARRAY_SIZE (omap34xx_vdd2_volt_data);
@@ -368,7 +368,7 @@ static int vc_bypass_scale_voltage(u32 vdd, unsigned long target_volt, current_vsel =omap_twl_uv_to_vsel (current_volt); smps_steps =abs (target_vsel - current_vsel); -if (vdd ==VDD1_OPP ) { +if (vdd ==VDD1 ) {u32 vc_cmdval0; vc_cmdval0 =voltage_read_reg (vc_reg.cmdval0_reg);
@@ -377,7 +377,7 @@ static int vc_bypass_scale_voltage(u32 vdd, unsigned long target_volt,voltage_write_reg (vc_reg.cmdval0_reg, vc_cmdval0); reg_addr =R_VDD1_SR_CONTROL ; - }else if (vdd ==VDD2_OPP ) { + }else if (vdd ==VDD2 ) {u32 vc_cmdval1; vc_cmdval1 =voltage_read_reg (vc_reg.cmdval1_reg);
@@ -387,7 +387,7 @@ static int vc_bypass_scale_voltage(u32 vdd, unsigned long target_volt, reg_addr =R_VDD2_SR_CONTROL ; }else {pr_warning ("Wrong VDD passed in vc_bypass_scale_voltage %d\n" , - vdd); + vdd +1 );return false; }
@@ -531,10 +531,10 @@ void omap_voltageprocessor_enable(int vp_id)* This latching is required only if VC bypass method is used for * voltage scaling during dvfs. */ -vp_latch_vsel (vp_id -1 ); - vpconfig =voltage_read_reg (vp_reg[vp_id -1 ].vp_offs.vpconfig_reg); +vp_latch_vsel (vp_id); + vpconfig =voltage_read_reg (vp_reg[vp_id].vp_offs.vpconfig_reg);/* Enable VP */ -voltage_write_reg (vp_reg[vp_id -1 ].vp_offs.vpconfig_reg, +voltage_write_reg (vp_reg[vp_id].vp_offs.vpconfig_reg, vpconfig |VP_CONFIG_VPENABLE ); }
@@ -551,7 +551,7 @@ void omap_voltageprocessor_disable(int vp_id)u32 vpconfig;/* Wait for VP idle before disabling VP */ -while ((!voltage_read_reg (vp_reg[vp_id -1 ].vp_offs.status_reg)) && +while ((!voltage_read_reg (vp_reg[vp_id].vp_offs.status_reg)) && i++ <MAX_TRIES )udelay (1 );
@@ -559,9 +559,9 @@ void omap_voltageprocessor_disable(int vp_id)pr_warning ("VP1 not idle, still going ahead with \ VP1 disable\n" );/* Disable VP1 */ - vpconfig =voltage_read_reg (vp_reg[vp_id -1 ].vp_offs.vpconfig_reg); + vpconfig =voltage_read_reg (vp_reg[vp_id].vp_offs.vpconfig_reg); vpconfig &= ~VP_CONFIG_VPENABLE ; -voltage_write_reg (vp_reg[vp_id -1 ].vp_offs.vpconfig_reg, vpconfig); +voltage_write_reg (vp_reg[vp_id].vp_offs.vpconfig_reg, vpconfig); }/**
@@ -597,19 +597,20 @@ void omap_reset_voltage(int vdd)char vsel;/* Should remove this once OPP framework is fixed */ -if ((vdd -1 ) ==VP1 ) { +if (vdd ==VDD1 ) { target_uvdc =get_curr_vdd1_voltage ();if (!target_uvdc)return ; - }else if ((vdd -1 ) ==VP2 ) { + }else if (vdd ==VDD2 ) { target_uvdc =get_curr_vdd2_voltage ();if (!target_uvdc)return ; }else { -pr_warning ("Wrong VDD passed in omap_reset_voltage %d\n" , vdd); +pr_warning ("Wrong VDD passed in omap_reset_voltage %d\n" , + vdd +1 );return ; } - vsel =voltage_read_reg (vp_reg[vdd -1 ].vp_offs.voltage_reg); + vsel =voltage_read_reg (vp_reg[vdd].vp_offs.voltage_reg); current_uvdc = (vsel *12500 ) +600000 ;omap_voltage_scale (vdd, target_uvdc, current_uvdc); }
arch/arm/mach-omap2/voltage.h +3 -3
@@ -10,9 +10,9 @@*/ #include "pm.h" -/* Voltageprocessor instances */ -#define VP1 0 -#define VP2 1 +/* VoltageDomain instances */ +#define VDD1 0 +#define VDD2 1/* Generic VP definitions. Need to be redefined for OMAP4 */
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 12/22 OMAP3: PM: Minimizing the passing around of sr id in smartreflex.c
This patch ensures that sr id is passed as a parameter only to public APIs in smartreflex.c and other APIs in smartreflex.c uses the omap_sr strucutres.
--- arch/arm/mach-omap2/smartreflex.c | 36 +++++++++++++----------------------- 1 files changed, 13 insertions(+), 23 deletions(-)
arch/arm/mach-omap2/smartreflex.c +13 -23
@@ -190,16 +190,8 @@ static void sr_configure(struct omap_sr *sr) sr->is_sr_reset =0 ; } -static void sr_start_vddautocomp (int srid) +static void sr_start_vddautocomp (struct omap_sr *sr) { -struct omap_sr *sr =_sr_lookup (srid); - -if (!sr) { -pr_warning ("omap_sr struct corresponding to SR%d not found\n" , - srid +1 ); -return ; - } -if (!sr_class || !(sr_class->enable)) {pr_warning ("smartreflex class driver not registered\n" );return ;
@@ -211,30 +203,22 @@ static void sr_start_vddautocomp(int srid) } sr->is_autocomp_active =1 ; -if (!sr_class->enable (srid)) { +if (!sr_class->enable (sr->srid)) { sr->is_autocomp_active =0 ;if (sr->is_sr_reset ==1 )sr_clk_disable (sr); } } -static void sr_stop_vddautocomp (int srid) +static void sr_stop_vddautocomp (struct omap_sr *sr) { -struct omap_sr *sr =_sr_lookup (srid); - -if (!sr) { -pr_warning ("omap_sr struct corresponding to SR%d not found\n" , - srid +1 ); -return ; - } -if (!sr_class || !(sr_class->disable)) {pr_warning ("smartreflex class driver not registered\n" );return ; }if (sr->is_autocomp_active ==1 ) { - sr_class->disable (srid); + sr_class->disable (sr->srid);sr_clk_disable (sr); sr->is_autocomp_active =0 ; }
@@ -426,9 +410,9 @@ static int omap_sr_autocomp_store(void *data, u64 val)return 0 ; }if (val ==0 ) -sr_stop_vddautocomp (sr_info->srid); +sr_stop_vddautocomp (sr_info);else -sr_start_vddautocomp (sr_info->srid); +sr_start_vddautocomp (sr_info);return 0 ; }
@@ -468,9 +452,15 @@ static int __devexit omap_smartreflex_remove(struct platform_device *pdev) {struct omap_sr *sr_info =_sr_lookup (pdev->id +1 ); +if (!sr_info) { +pr_warning ("omap_sr struct corresponding to SR%d not found\n" , + pdev->id +1 ); +return 0 ; + } +/* Disable Autocompensation if enabled before removing the module */ if (sr_info->is_autocomp_active ==1 ) -sr_stop_vddautocomp (sr_info->srid); +sr_stop_vddautocomp (sr_info);list_del (&sr_info->node);kfree (sr_info);
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 13/22 OMAP3: PM: Cleaning up of smartreflex header file.
This patch cleans up smartreflex.h removing all unnecessary and duplicate definitions.
--- arch/arm/mach-omap2/smartreflex.h | 96 +++++++++++++++++++++---------------- 1 files changed, 55 insertions(+), 41 deletions(-)
arch/arm/mach-omap2/smartreflex.h +55 -41
@@ -18,54 +18,38 @@extern struct dentry *pm_dbg_main_dir; -#define PHY_TO_OFF_PM_RECIEVER (p) (p - 0x5b) -/* SMART REFLEX REG ADDRESS OFFSET */ -#define SRCONFIG 0x00 -#define SRSTATUS 0x04 -#define SENVAL 0x08 -#define SENMIN 0x0C -#define SENMAX 0x10 -#define SENAVG 0x14 -#define AVGWEIGHT 0x18 +#define SRCONFIG 0x00 +#define SRSTATUS 0x04 +#define SENVAL 0x08 +#define SENMIN 0x0C +#define SENMAX 0x10 +#define SENAVG 0x14 +#define AVGWEIGHT 0x18#define NVALUERECIPROCAL 0x1C -#define SENERROR 0x20 -#define ERRCONFIG 0x24 +#define SENERROR 0x20 +#define ERRCONFIG 0x24 -#define GAIN_MAXLIMIT 16 -#define R_MAXLIMIT 256 - -#define SR1_CLK_ENABLE BIT(6) -#define SR2_CLK_ENABLE BIT(7) +/* Bit/Shift Positions */ /* SRCONFIG */ -#define SR1_SRCONFIG_ACCUMDATA (0x1F4 << 22) -#define SR2_SRCONFIG_ACCUMDATA (0x1F4 << 22) - -#define SRCLKLENGTH_12MHZ_SYSCLK 0x3C -#define SRCLKLENGTH_13MHZ_SYSCLK 0x41 -#define SRCLKLENGTH_19MHZ_SYSCLK 0x60 -#define SRCLKLENGTH_26MHZ_SYSCLK 0x82 -#define SRCLKLENGTH_38MHZ_SYSCLK 0xC0 - +#define SRCONFIG_ACCUMDATA_SHIFT 22#define SRCONFIG_SRCLKLENGTH_SHIFT 12#define SRCONFIG_SENNENABLE_SHIFT 5#define SRCONFIG_SENPENABLE_SHIFT 3 +#define SRCONFIG_CLKCTRL_SHIFT 0 + +#define SRCONFIG_ACCUMDATA_MASK (0x3FF << 22)#define SRCONFIG_SRENABLE BIT(11)#define SRCONFIG_SENENABLE BIT(10)#define SRCONFIG_ERRGEN_EN BIT(9)#define SRCONFIG_MINMAXAVG_EN BIT(8) -#define SRCONFIG_DELAYCTRL BIT(2) -#define SRCONFIG_CLKCTRL (0x00 << 0)/* AVGWEIGHT */ -#define SR1_AVGWEIGHT_SENPAVGWEIGHT (0x03 << 2) -#define SR1_AVGWEIGHT_SENNAVGWEIGHT (0x03 << 0) - -#define SR2_AVGWEIGHT_SENPAVGWEIGHT BIT(2) -#define SR2_AVGWEIGHT_SENNAVGWEIGHT BIT(0) +#define AVGWEIGHT_SENPAVGWEIGHT_SHIFT 2 +#define AVGWEIGHT_SENNAVGWEIGHT_SHIFT 0/* NVALUERECIPROCAL */ #define NVALUERECIPROCAL_SENPGAIN_SHIFT 20
@@ -74,25 +58,55 @@ extern struct dentry *pm_dbg_main_dir;#define NVALUERECIPROCAL_RNSENN_SHIFT 0/* ERRCONFIG */ -#define SR_CLKACTIVITY_MASK (0x03 << 20) +#define ERRCONFIG_ERRWEIGHT_SHIFT 16 +#define ERRCONFIG_ERRMAXLIMIT_SHIFT 8 +#define ERRCONFIG_ERRMINLIMIT_SHIFT 0 +#define SR_ERRWEIGHT_MASK (0x07 << 16)#define SR_ERRMAXLIMIT_MASK (0xFF << 8)#define SR_ERRMINLIMIT_MASK (0xFF << 0)#define ERRCONFIG_VPBOUNDINTEN BIT(31)#define ERRCONFIG_VPBOUNDINTST BIT(30) +#define ERRCONFIG_MCUACCUMINTEN BIT(29) +#define ERRCONFIG_MCUACCUMINTST BIT(28) +#define ERRCONFIG_MCUVALIDINTEN BIT(27) +#define ERRCONFIG_MCUVALIDINTST BIT(26) +#define ERRCONFIG_MCUBOUNDINTEN BIT(25) +#define ERRCONFIG_MCUBOUNDINTST BIT(24) +#define ERRCONFIG_MCUDISACKINTEN BIT(23) +#define ERRCONFIG_MCUDISACKINTST BIT(22) -#define SR1_ERRWEIGHT (0x07 << 16) -#define SR1_ERRMAXLIMIT (0x02 << 8) -#define SR1_ERRMINLIMIT (0xFA << 0) +/* Common Bit values */ -#define SR2_ERRWEIGHT (0x07 << 16) -#define SR2_ERRMAXLIMIT (0x02 << 8) -#define SR2_ERRMINLIMIT (0xF9 << 0) +#define SRCLKLENGTH_12MHZ_SYSCLK 0x3C +#define SRCLKLENGTH_13MHZ_SYSCLK 0x41 +#define SRCLKLENGTH_19MHZ_SYSCLK 0x60 +#define SRCLKLENGTH_26MHZ_SYSCLK 0x82 +#define SRCLKLENGTH_38MHZ_SYSCLK 0xC0 -/* Vmode control */ -#define R_DCDC_GLOBAL_CFG PHY_TO_OFF_PM_RECIEVER(0x61) +/* +* 3430 specific values. Maybe these should be passed from board file or +* pmic structures. +*/ +#define OMAP3430_SR_ACCUMDATA 0x1F4 + +#define OMAP3430_SR1_SENPAVGWEIGHT 0x03 +#define OMAP3430_SR1_SENNAVGWEIGHT 0x03 + +#define OMAP3430_SR2_SENPAVGWEIGHT 0x01 +#define OMAP3430_SR2_SENNAVGWEIGHT 0x01 + +#define OMAP3430_SR_ERRWEIGHT 0x07 +#define OMAP3430_SR_ERRMAXLIMIT 0x02 +#define OMAP3430_SR1_ERRMINLIMIT 0xFA +#define OMAP3430_SR2_ERRMINLIMIT 0xF9 +/* TODO:3630/OMAP4 values if it has to come from this file */ + +/* Info for enabling SR in T2/gaia. ToDo: Move it to twl4030_power.c */ +#define PHY_TO_OFF_PM_RECIEVER (p) (p - 0x5b) +#define R_DCDC_GLOBAL_CFG PHY_TO_OFF_PM_RECIEVER(0x61)/* R_DCDC_GLOBAL_CFG register, SMARTREFLEX_ENABLE values */ #define DCDC_GLOBAL_CFG_ENABLE_SRFLX 0x08
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 14/22 OMAP3: PM: Configurations for Smartreflex Class 2 and Smartreflex Class 3
There are two separate modules in SmartReflex-AVS :
MinMaxAvg module and Error module. Class3 uses the Error module only. In Class2 you can choose between either module since it is software based. The registers are mapped to the modules as followed:
MinMaxAvg module: AccumData, MinMaxAvgEnable, MinMaxAvgValid,
MinMaxAvgAccumValid, SenVal, SenMin, SenMax, SenAverage, AverageWeight, MCUAccum, MCUValid, MCUBounds.
Error module: SenNGain, SenPGain, SenPRN, SenNRN, AvgError,
SenError, VPBounds, ErrWeight, ErrMaxLimit, ErrMinLimit.
Shared between both: SRClkLength, SREnable, SenEnable, SenNEnable,
SenPEnable, DelayCtrl, MCUDisableAck, ClkActivity.
This patch generates separate API's to configure the two modules which can be used by the smartreflex class driver as per its requirement. This patch allows allows for registering for smartreflex interrupt handler and notification of interrupts in case requested by the smartreflex class driver.
--- arch/arm/mach-omap2/smartreflex-class3.c | 7 + arch/arm/mach-omap2/smartreflex.c | 253 +++++++++++++++++++++++------- arch/arm/mach-omap2/smartreflex.h | 14 ++ 3 files changed, 219 insertions(+), 55 deletions(-)
arch/arm/mach-omap2/smartreflex-class3.c +7 -0
@@ -39,10 +39,17 @@ static int sr_class3_disable(int id)return true; } +static void sr_class3_configure (int id) +{ +sr_configure_errgen (id); +} +/* SR class3 structure */ struct omap_smartreflex_class_data class3_data = { .enable = sr_class3_enable, .disable = sr_class3_disable, + .configure = sr_class3_configure, + .class_type =SR_CLASS3 , };int __init sr_class3_init (void )
arch/arm/mach-omap2/smartreflex.c +198 -55
336 lines not on this page · raw message
arch/arm/mach-omap2/smartreflex.h +14 -0
@@ -151,12 +151,23 @@ struct omap_smartreflex_dev_data { };#ifdef CONFIG_OMAP_SMARTREFLEX +/* +* The smart reflex driver supports CLASS1 CLASS2 and CLASS3 SR. +* The smartreflex class driver should pass the class type. +* Should be used to populate the class_type field of the +* omap_smartreflex_class_data structure. +*/ +#define SR_CLASS1 0x1 +#define SR_CLASS2 0x2 +#define SR_CLASS3 0x3 +/** * omap_smartreflex_class_data : Structure to be populated by * Smartreflex class driver with corresponding class enable disable API's * * @enable - API to enable a particular class smaartreflex. * @disable - API to disable a particular class smartreflex. +* @configure - API to configure a particular class smartreflex. * @notify - API to notify the class driver about an event in SR. Not needed * for class3. * @notify_flags - specify the events to be notified to the class driver
@@ -166,6 +177,7 @@ struct omap_smartreflex_dev_data {struct omap_smartreflex_class_data {int (*enable)(int sr_id);int (*disable)(int sr_id); +void (*configure)(int sr_id);int (*notify)(int sr_id,u32 status);u8 notify_flags;u8 class_type;
@@ -207,6 +219,8 @@ void omap_smartreflex_disable(int srid);*/ int sr_enable (int srid,unsigned long volt);void sr_disable (int srid); +void sr_configure_errgen (int srid); +void sr_configure_minmax (int srid);/* * API to register the smartreflex class driver with the smartreflex driver
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 15/22 OMAP3: PM: Support for enabling smartreflex autocompensation by default.
This patch adds support to pdata enable smartreflex autocompenstion during init based on enable_on_init flag passed as pdata.
This patch also adds enabling of autocompensation by default (setting enable_on_init flag to true) in case of ES3.1 OMAP3430 chip. In the current implementation
this step is kept in smartreflex.c itself.Later an API can be added so that the decision to enable autocompensation by default can be passed from the corresponding board files.
--- arch/arm/mach-omap2/smartreflex.c | 5 +++++ arch/arm/mach-omap2/sr_device.c | 16 +++++++++++++++- 2 files changed, 20 insertions(+), 1 deletions(-)
arch/arm/mach-omap2/smartreflex.c +5 -0
@@ -239,6 +239,7 @@ static void sr_stop_vddautocomp(struct omap_sr *sr)static int sr_late_init (struct omap_sr *sr_info) {char name[SMARTREFLEX_NAME_LEN ]; +struct omap_smartreflex_data *pdata = sr_info->pdev->dev.platform_data;int ret =0 ; if (sr_class->class_type == SR_CLASS2 &&
@@ -252,6 +253,10 @@ static int sr_late_init(struct omap_sr *sr_info) handler for SR%d. Smartreflex will \ not function as desired\n", sr_info->srid); } + +if (pdata->enable_on_init) +sr_start_vddautocomp (sr_info); +return ret; }
arch/arm/mach-omap2/sr_device.c +15 -1
@@ -117,7 +117,21 @@ static int __init omap_devinit_smartreflex(void)if (WARN_ON (!sr_data))return -ENOMEM ; - sr_data->enable_on_init = false; +/* +* OMAP3430 ES3.1 chips by default come with Efuse burnt +* with parameters required for full functionality of +* smartreflex AVS feature like ntarget values , sennenable +* and senpenable. So enable the SR AVS feature during boot up +* itself if it is a OMAP3430 ES3.1 chip. +*/ +if (cpu_is_omap343x ()) { +if (omap_rev () ==OMAP3430_REV_ES3_1 ) + sr_data->enable_on_init = true; +else + sr_data->enable_on_init = false; + }else { + sr_data->enable_on_init = false; + } sr_data->device_enable = omap_device_enable; sr_data->device_shutdown = omap_device_shutdown; sr_data->device_idle = omap_device_idle;
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 16/22 OMAP3: PM: Correcting accessing of ERRCONFIG register in smartreflex.c
Smartreflex error config register is special as it contains certain status bits which if written a 1 into means a clear of those bits. This patch takes special care during modify of this register that no status bits in this register are accidently set to 1.
This issue was first reported by Nishanth Menon.
--- arch/arm/mach-omap2/smartreflex.c | 11 +++++++++++ arch/arm/mach-omap2/smartreflex.h | 6 ++++++ 2 files changed, 17 insertions(+), 0 deletions(-)
arch/arm/mach-omap2/smartreflex.c +11 -0
@@ -71,6 +71,17 @@ static inline void sr_modify_reg(struct omap_sr *sr, unsigned offset, u32 mask, reg_val =omap_hwmod_readl (odev->hwmods[0 ], offset); reg_val &= ~mask; +/* +* Smartreflex error config register is special as it contains +* certain status bits which if written a 1 into means a clear +* of those bits. So in order to make sure no accidental write of +* 1 happens to those status bits, do a clear of them in the read +* value. Now if there is an actual reguest to write to these bits +* they will be set in the nex step. +*/ +if (offset ==ERRCONFIG ) + reg_val &= ~ERRCONFIG_STATUS_MASK ; + reg_val |= value;omap_hwmod_writel (reg_val, odev->hwmods[0 ], offset);
arch/arm/mach-omap2/smartreflex.h +6 -0
@@ -77,6 +77,12 @@ extern struct dentry *pm_dbg_main_dir;#define ERRCONFIG_MCUDISACKINTEN BIT(23)#define ERRCONFIG_MCUDISACKINTST BIT(22) +#define ERRCONFIG_STATUS_MASK (ERRCONFIG_VPBOUNDINTST | \ + ERRCONFIG_MCUACCUMINTST | \ + ERRCONFIG_MCUVALIDINTST | \ + ERRCONFIG_MCUBOUNDINTST | \ + ERRCONFIG_MCUDISACKINTST) +/* Common Bit values */ #define SRCLKLENGTH_12MHZ_SYSCLK 0x3C
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 17/22 OMAP3: PM: Implement latest h/w recommendations for SR and VP registers and SR VP enable disable sequence.
This patch introduces OMAP3 specific values for Smartreflex and Voltage processor registers as per the latest TI recommendations. This patch adds smartreflex errminlimit and voltage processor errorgain into the voltage tables as they vary with different voltages. This patch also improves the smartreflex and voltage processor enable disable sequences as per the latest recommendations.
These recommendations were first formed based on experimentations on N900 platform and were implemented in the N900 codebase base first by Nishanth Menon and Paul Walmsley.
--- arch/arm/mach-omap2/smartreflex.c | 54 +++++++++++++++---- arch/arm/mach-omap2/smartreflex.h | 4 +- arch/arm/mach-omap2/voltage.c | 103 +++++++++++++++++++++++++++++------- arch/arm/mach-omap2/voltage.h | 25 ++++++--- 4 files changed, 142 insertions(+), 44 deletions(-)
arch/arm/mach-omap2/smartreflex.c +42 -12
@@ -27,14 +27,17 @@#include <linux/io.h> #include <linux/list.h> #include <linux/debugfs.h> +#include <linux/delay.h> #include <plat/omap_hwmod.h> #include <plat/omap_device.h> +#include <plat/common.h> #include "voltage.h" #include "smartreflex.h" #define SMARTREFLEX_NAME_LEN 16 +#define SR_DISABLE_TIMEOUT 200struct omap_sr {int srid;
@@ -190,11 +193,9 @@ static void sr_set_regfields(struct omap_sr *sr) sr->err_maxlimit =OMAP3430_SR_ERRMAXLIMIT ; sr->accum_data =OMAP3430_SR_ACCUMDATA ;if (sr->srid ==VDD1 ) { - sr->err_minlimit =OMAP3430_SR1_ERRMINLIMIT ; sr->senn_avgweight =OMAP3430_SR1_SENNAVGWEIGHT ; sr->senp_avgweight =OMAP3430_SR1_SENPAVGWEIGHT ; }else { - sr->err_minlimit =OMAP3430_SR2_ERRMINLIMIT ; sr->senn_avgweight =OMAP3430_SR2_SENNAVGWEIGHT ; sr->senp_avgweight =OMAP3430_SR2_SENPAVGWEIGHT ; }
@@ -209,11 +210,6 @@ static void sr_start_vddautocomp(struct omap_sr *sr)return ; } -if (sr->is_sr_reset ==1 ) { -sr_clk_enable (sr); - sr_class->configure (sr->srid); - } - sr->is_autocomp_active =1 ;if (!sr_class->enable (sr->srid)) { sr->is_autocomp_active =0 ;
@@ -407,6 +403,13 @@ int sr_enable(int srid, unsigned long volt)return false; } +/* errminlimit is opp dependent and hence linked to voltage */ + sr->err_minlimit = volt_data.sr_errminlimit; + +/* Enable the clocks and configure SR */ +sr_clk_enable (sr); + sr_class->configure (sr->srid); +sr_write_reg (sr,NVALUERECIPROCAL , nvalue_reciprocal);/* SRCONFIG - enable SR */ sr_modify_reg (sr,SRCONFIG ,SRCONFIG_SRENABLE ,SRCONFIG_SRENABLE );
@@ -423,6 +426,7 @@ int sr_enable(int srid, unsigned long volt)void sr_disable (int srid) {struct omap_sr *sr =_sr_lookup (srid); +int timeout =0 ;if (!sr) { pr_warning("omap_sr struct corresponding to SR%d not found\n",
@@ -430,10 +434,39 @@ void sr_disable(int srid)return ; } - sr->is_sr_reset =1 ; +/* Check if SR is already disabled. If yes do nothing */ +if (!(sr_read_reg (sr,SRCONFIG ) &SRCONFIG_SRENABLE )) +return ; + +/* Enable MCUDisableAcknowledge interrupt */ +sr_modify_reg (sr,ERRCONFIG , +ERRCONFIG_MCUDISACKINTEN ,ERRCONFIG_MCUDISACKINTEN ); +/* SRCONFIG - disable SR */ -sr_modify_reg (sr,SRCONFIG ,SRCONFIG_SRENABLE , ~SRCONFIG_SRENABLE ); +sr_modify_reg (sr,SRCONFIG ,SRCONFIG_SRENABLE ,0x0 ); + +/* Disable all other SR interrupts and clear the status */ +sr_modify_reg (sr,ERRCONFIG , + (ERRCONFIG_MCUACCUMINTEN |ERRCONFIG_MCUVALIDINTEN | +ERRCONFIG_MCUBOUNDINTEN |ERRCONFIG_VPBOUNDINTEN ), + (ERRCONFIG_MCUACCUMINTST |ERRCONFIG_MCUVALIDINTST | +ERRCONFIG_MCUBOUNDINTST |ERRCONFIG_VPBOUNDINTST )); +/* Wait for SR to be disabled. +* wait until ERRCONFIG.MCUDISACKINTST = 1. Typical latency is 1us. +*/ +omap_test_timeout ((sr_read_reg (sr,ERRCONFIG ) & +ERRCONFIG_MCUDISACKINTST ),SR_DISABLE_TIMEOUT , + timeout); + +if (timeout >=SR_DISABLE_TIMEOUT ) +pr_warning ("SR%d disable timedout\n" , srid); + +/* Disable MCUDisableAcknowledge interrupt & clear pending interrupt +* Also enable VPBOUND interrrupt +*/ +sr_modify_reg (sr,ERRCONFIG ,ERRCONFIG_MCUDISACKINTEN , +ERRCONFIG_MCUDISACKINTST ); }/**
@@ -463,9 +496,6 @@ void omap_smartreflex_enable(int srid)if (sr->is_autocomp_active ==1 ) {if (sr->is_sr_reset ==1 ) { -/* Enable SR clks */ -sr_clk_enable (sr); - sr_class->configure (srid);if (!sr_class->enable (srid))sr_clk_disable (sr); }
arch/arm/mach-omap2/smartreflex.h +1 -3
@@ -103,10 +103,8 @@ extern struct dentry *pm_dbg_main_dir;#define OMAP3430_SR2_SENPAVGWEIGHT 0x01#define OMAP3430_SR2_SENNAVGWEIGHT 0x01 -#define OMAP3430_SR_ERRWEIGHT 0x07 +#define OMAP3430_SR_ERRWEIGHT 0x04#define OMAP3430_SR_ERRMAXLIMIT 0x02 -#define OMAP3430_SR1_ERRMINLIMIT 0xFA -#define OMAP3430_SR2_ERRMINLIMIT 0xF9/* TODO:3630/OMAP4 values if it has to come from this file */
arch/arm/mach-omap2/voltage.c +83 -20
178 lines not on this page · raw message
arch/arm/mach-omap2/voltage.h +16 -9
@@ -20,6 +20,7 @@#define VP_CONFIG_INITVDD OMAP3430_INITVDD#define VP_FORCEUPDATE OMAP3430_FORCEUPDATE#define VP_CONFIG_VPENABLE OMAP3430_VPENABLE +#define VP_ERRORGAIN_MASK OMAP3430_ERRORGAIN_MASK#define VP_INITVOLTAGE_MASK OMAP3430_INITVOLTAGE_MASK#define VP_INITVOLTAGE_SHIFT OMAP3430_INITVOLTAGE_SHIFT
@@ -50,28 +51,34 @@* board file or PMIC data structure */ #define OMAP3_VP_CONFIG_ERROROFFSET 0x00 -#define OMAP3_VP_CONFIG_ERRORGAIN 0x20 -#define OMAP3_VP_VSTEPMIN_SMPSWAITTIMEMIN 0x01F4 +#define OMAP3_VP_VSTEPMIN_SMPSWAITTIMEMIN 0x3C#define OMAP3_VP_VSTEPMIN_VSTEPMIN 0x1 -#define OMAP3_VP_VSTEPMAX_SMPSWAITTIMEMAX 0x01F4 +#define OMAP3_VP_VSTEPMAX_SMPSWAITTIMEMAX 0x3C#define OMAP3_VP_VSTEPMAX_VSTEPMAX 0x04 -#define OMAP3_VP1_VLIMITTO_VDDMIN 0x0 -#define OMAP3_VP1_VLIMITTO_VDDMAX 0x3C +#define OMAP3_VP1_VLIMITTO_VDDMIN 0x14 +#define OMAP3_VP1_VLIMITTO_VDDMAX 0x42#define OMAP3_VP2_VLIMITTO_VDDMAX 0x2C -#define OMAP3_VP2_VLIMITTO_VDDMIN 0x0 -#define OMAP3_VP_VLIMITTO_TIMEOUT 0xFFFF +#define OMAP3_VP2_VLIMITTO_VDDMIN 0x18 +#define OMAP3_VP_VLIMITTO_TIMEOUT_US 0x200/* TODO OMAP4 VP register values if the same file is used for OMAP4*/ /** * omap_volt_data - Omap voltage specific data. * -* @voltage : The possible voltage value -* @sr_nvalue : Smartreflex N target value at voltage <voltage> +* @voltage : The possible voltage value +* @sr_nvalue : Smartreflex N target value at voltage <voltage> +* @sr_errminlimit : Error min limit value for smartreflex. This value +* differs at differnet opp and thus is linked +* with voltage. +* @vp_errorgain : Error gain value for the voltage processor. This +* field also differs according to the voltage/opp. */ struct omap_volt_data {unsigned long voltage;u32 sr_nvalue; +u8 sr_errminlimit; +u8 vp_errorgain; };void omap_voltageprocessor_enable (int vp_id);
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 18/22 OMAP3: PM: Optional reset of voltage during Smartreflex disable.
Currently whenever smartreflex is disabled the voltage for the particular VDD is reset to the non-smartreflex compensated level. This step is unnecessary during dvfs because anyways in the next couple of steps before re-enabling smartreflex , the voltage level is changed.
This patch adds the flexibility in the smartreflex framework for the user to specify whether or not a voltage reset is required after disabling of smartrefelx. The smartreflex driver just passes on this info to the smartreflex class driver, which ultimately takes the decision to reset the voltage or not.
--- arch/arm/mach-omap2/pm34xx.c | 4 ++-- arch/arm/mach-omap2/smartreflex-class3.c | 5 +++-- arch/arm/mach-omap2/smartreflex.c | 10 +++++++--- arch/arm/mach-omap2/smartreflex.h | 4 ++-- 4 files changed, 14 insertions(+), 9 deletions(-)
arch/arm/mach-omap2/pm34xx.c +2 -2
@@ -415,9 +415,9 @@ void omap_sram_idle(void)* Only needed if we are going to enter retention or off. */ if (mpu_next_state <=PWRDM_POWER_RET ) -omap_smartreflex_disable (VDD1 ); +omap_smartreflex_disable (VDD1 ,1 );if (core_next_state <=PWRDM_POWER_RET ) -omap_smartreflex_disable (VDD2 ); +omap_smartreflex_disable (VDD2 ,1 );/* CORE */ if (core_next_state <PWRDM_POWER_ON ) {
arch/arm/mach-omap2/smartreflex-class3.c +3 -2
@@ -30,11 +30,12 @@ static int sr_class3_enable(int id)return sr_enable (id, volt); } -static int sr_class3_disable (int id) +static int sr_class3_disable (int id,int is_volt_reset) {omap_voltageprocessor_disable (id);sr_disable (id); -omap_reset_voltage (id); +if (is_volt_reset) +omap_reset_voltage (id);return true; }
arch/arm/mach-omap2/smartreflex.c +7 -3
@@ -226,7 +226,7 @@ static void sr_stop_vddautocomp(struct omap_sr *sr) }if (sr->is_autocomp_active ==1 ) { - sr_class->disable (sr->srid); + sr_class->disable (sr->srid,1 );sr_clk_disable (sr); sr->is_autocomp_active =0 ; }
@@ -506,12 +506,16 @@ void omap_smartreflex_enable(int srid)* omap_smartreflex_disable : API to disable SR clocks and to call into the * registered smartreflex class disable API. * @srid - The id of the sr module to be disabled. +* @is_volt_reset - Whether the voltage needs to be reset after disabling +* smartreflex module or not. This parameter is directly +* passed on to the smartreflex class disable which takes the +* appropriate action. * * This API is to be called from the kernel in order to disable * a particular smartreflex module. This API will in turn call * into the registered smartreflex class disable API. */ -void omap_smartreflex_disable (int srid) +void omap_smartreflex_disable (int srid,int is_volt_reset) {struct omap_sr *sr =_sr_lookup (srid);
@@ -528,7 +532,7 @@ void omap_smartreflex_disable(int srid)if (sr->is_autocomp_active ==1 ) {if (sr->is_sr_reset ==0 ) { - sr_class->disable (srid); + sr_class->disable (srid, is_volt_reset);/* Disable SR clk */ sr_clk_disable (sr); }
arch/arm/mach-omap2/smartreflex.h +2 -2
@@ -180,7 +180,7 @@ struct omap_smartreflex_dev_data {*/ struct omap_smartreflex_class_data {int (*enable)(int sr_id); -int (*disable)(int sr_id); +int (*disable)(int sr_id,int is_volt_reset);void (*configure)(int sr_id);int (*notify)(int sr_id,u32 status);u8 notify_flags;
@@ -216,7 +216,7 @@ struct omap_smartreflex_data {* do anything. */ void omap_smartreflex_enable (int srid); -void omap_smartreflex_disable (int srid); +void omap_smartreflex_disable (int srid,int is_volt_reset);/* * Smartreflex driver hooks to be called from Smartreflex class driver
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 19/22 OMAP3: PM: Disabling Smartreflex across both frequency and voltage scaling during DVFS.
This patch disables smartreflex across both frequency and voltage scaling instead of just across voltage scaling as before. This is the hardware recommended practice.
This bug was first reported and solved on Nokia N900 code base by Nishanth Menon and Paul Walmsley.
This patch also does some changes in SRF to adapt to the new smartreflex and voltage driver.
--- arch/arm/mach-omap2/resource34xx.c | 27 ++++++++++----------------- arch/arm/mach-omap2/resource34xx.h | 1 - 2 files changed, 10 insertions(+), 18 deletions(-)
arch/arm/mach-omap2/resource34xx.c +10 -17
@@ -28,6 +28,7 @@#include <plat/opp_twl_tps.h> #include "smartreflex.h" +#include "voltage.h" #include "resource34xx.h" #include "pm.h" #include "cm.h"
@@ -331,12 +332,6 @@ static int program_opp(int res, enum opp_t opp_type, int target_level, {int i, ret =0 , raise;unsigned long freq; -#ifdef CONFIG_OMAP_SMARTREFLEX -unsigned long t_opp, c_opp; - - t_opp =ID_VDD (res) |ID_OPP_NO (target_level); - c_opp =ID_VDD (res) |ID_OPP_NO (current_level); -#endif /* See if have a freq associated, if not, invalid opp */ ret =opp_to_freq (&freq, opp_type, target_level);
@@ -348,15 +343,15 @@ static int program_opp(int res, enum opp_t opp_type, int target_level,else raise =0 ; +omap_smartreflex_disable (res -1 ,0 ); +for (i =0 ; i <2 ; i++) { -if (i == raise) +if (i == raise) { ret =program_opp_freq (res, target_level, current_level); -#ifdef CONFIG_OMAP_SMARTREFLEX - else { -u8 vc, vt; + }else {struct omap_opp *oppx; -unsigned long uvdc; +unsigned long uvdc_current, uvdc_target;/* * transitioning from good to good OPP
@@ -364,21 +359,19 @@ static int program_opp(int res, enum opp_t opp_type, int target_level,*/ oppx =opp_find_freq_exact (opp_type, freq, true);BUG_ON (IS_ERR (oppx)); - uvdc =opp_get_voltage (oppx); - vt =omap_twl_uv_to_vsel (uvdc); + uvdc_target =opp_get_voltage (oppx);BUG_ON (opp_to_freq (&freq, opp_type, current_level)); oppx =opp_find_freq_exact (opp_type, freq, true);BUG_ON (IS_ERR (oppx)); - uvdc =opp_get_voltage (oppx); - vc =omap_twl_uv_to_vsel (uvdc); + uvdc_current =opp_get_voltage (oppx);/* ok to scale.. */ - sr_voltagescale_vcbypass(t_opp, c_opp, vt, vc); +omap_voltage_scale (res -1 , uvdc_target, uvdc_current); } -#endif } +omap_smartreflex_enable (res -1 );return ret; }
arch/arm/mach-omap2/resource34xx.h +0 -1
@@ -30,7 +30,6 @@#include <plat/opp.h> #include <plat/omap34xx.h> -extern int sr_voltagescale_vcbypass (u32 t_opp,u32 c_opp,u8 t_vsel,u8 c_vsel);extern void lock_scratchpad_sem (void );extern void unlock_scratchpad_sem (void );
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 20/22 OMAP3: PM: VP force update method of voltage scaling
This patch introduces VP force update method of voltage scaling and enables it by default. The older method of vc bypass is now configuratble through a menu config option. VP force update is the hardware recommended method of voltage scaling.
--- arch/arm/mach-omap2/voltage.c | 175 +++++++++++++++++++++++++++++++++++++++-- arch/arm/mach-omap2/voltage.h | 3 + 2 files changed, 172 insertions(+), 6 deletions(-)
arch/arm/mach-omap2/voltage.c +169 -6
@@ -35,6 +35,7 @@#include "voltage.h" #define VP_IDLE_TIMEOUT 200 +#define VP_TRANXDONE_TIMEOUT 300/** * OMAP3 Voltage controller SR parameters. TODO: Pass this info as part of
@@ -80,6 +81,7 @@ struct vp_info {u32 vp_vddmin;u32 vp_vddmax;u32 vp_timeout; +u32 vp_tranxdone_status; };static struct vp_info *vp_reg;/*
@@ -166,6 +168,9 @@ static struct omap_volt_data omap34xx_vdd2_volt_data[] = { {1150000, 0, 0xF9, 0x18}, }; +/* By default VPFORCEUPDATE is the chosen method of voltage scaling */ +static bool voltscale_vpforceupdate = true; +static inline u32 voltage_read_reg (u8 offset) {return prm_read_mod_reg (volt_mod, offset);
@@ -325,6 +330,8 @@ static void __init vp_data_configure(int vp_id) OMAP3430_VDDMIN_SHIFT); vp_reg[vp_id].vp_vddmax = (OMAP3_VP1_VLIMITTO_VDDMAX <<OMAP3430_VDDMAX_SHIFT ); + vp_reg[vp_id].vp_tranxdone_status = +OMAP3430_VP1_TRANXDONE_ST ; }else if (vp_id ==VDD2 ) { vp_reg[vp_id].volt_data = omap34xx_vdd2_volt_data; vp_reg[vp_id].volt_data_count =
@@ -334,6 +341,8 @@ static void __init vp_data_configure(int vp_id) OMAP3430_VDDMIN_SHIFT); vp_reg[vp_id].vp_vddmax = (OMAP3_VP2_VLIMITTO_VDDMAX <<OMAP3430_VDDMAX_SHIFT ); + vp_reg[vp_id].vp_tranxdone_status = +OMAP3430_VP2_TRANXDONE_ST ; }else {pr_warning ("Voltage processor%d does not exisit\ in OMAP3 \n" , vp_id);
@@ -476,6 +485,134 @@ static int vc_bypass_scale_voltage(u32 vdd, unsigned long target_volt,return true; } +/* VP force update method of voltage scaling */ +static int vp_forceupdate_scale_voltage (u32 vdd,unsigned long target_volt, +unsigned long current_volt) +{ +u32 smps_steps =0 , smps_delay =0 ; +u32 vpconfig; +int timeout =0 ; +u8 target_vsel, current_vsel; + +if (!((vdd ==VDD1 ) || (vdd ==VDD2 ))) { +pr_warning ("Wrong vdd id passed to vp forceupdate\n" ); +return false; + } + + target_vsel =omap_twl_uv_to_vsel (target_volt); + current_vsel =omap_twl_uv_to_vsel (current_volt); + smps_steps =abs (target_vsel - current_vsel); + +if (vdd ==VDD1 ) { +u32 vc_cmdval0; + + vc_cmdval0 =voltage_read_reg (vc_reg.cmdval0_reg); + vc_cmdval0 &= ~VC_CMD_ON_MASK ; + vc_cmdval0 |= (target_vsel <<VC_CMD_ON_SHIFT ); +voltage_write_reg (vc_reg.cmdval0_reg, vc_cmdval0); + }else if (vdd ==VDD2 ) { +u32 vc_cmdval1; + + vc_cmdval1 =voltage_read_reg (vc_reg.cmdval1_reg); + vc_cmdval1 &= ~VC_CMD_ON_MASK ; + vc_cmdval1 |= (target_vsel <<VC_CMD_ON_SHIFT ); +voltage_write_reg (vc_reg.cmdval1_reg, vc_cmdval1); + } + +/* +* Clear all pending TransactionDone interrupt/status. Typical latency +* is <3us +*/ +while (timeout++ <VP_TRANXDONE_TIMEOUT ) { +prm_write_mod_reg (vp_reg[vdd].vp_tranxdone_status, +OCP_MOD ,PRM_IRQSTATUS_REG_OFFSET ); +if (!(prm_read_mod_reg (OCP_MOD ,PRM_IRQSTATUS_REG_OFFSET ) & + vp_reg[vdd].vp_tranxdone_status)) +break ; +udelay (1 ); + } + +if (timeout >=VP_TRANXDONE_TIMEOUT ) { +pr_warning ("VP%d TRANXDONE timeout exceeded. Voltage change \ +aborted" , vdd); +return false; + } + +/* OMAP3430 has errorgain varying btw higher and lower opp's */ +if (cpu_is_omap34xx ()) { +struct omap_volt_data volt_data; + +if (omap_match_volt (vdd, target_volt, &volt_data)) { +pr_warning ("Unable to get voltage table for VDD%d \ +during voltage scaling. Some really Wrong!" , + vdd +1 ); +return false; + } + vp_reg[vdd].vp_errorgain = (volt_data.vp_errorgain << +OMAP3430_ERRORGAIN_SHIFT ); + } + +/* Configure for VP-Force Update */ + vpconfig =voltage_read_reg (vp_reg[vdd].vp_offs.vpconfig_reg); + vpconfig &= ~(VP_CONFIG_INITVDD |VP_FORCEUPDATE | +VP_INITVOLTAGE_MASK |VP_ERRORGAIN_MASK ); + vpconfig |= ((target_vsel <<VP_INITVOLTAGE_SHIFT ) | + vp_reg[vdd].vp_errorgain); +voltage_write_reg (vp_reg[vdd].vp_offs.vpconfig_reg, vpconfig); + +/* Trigger initVDD value copy to voltage processor */ + vpconfig |=VP_CONFIG_INITVDD ; +voltage_write_reg (vp_reg[vdd].vp_offs.vpconfig_reg, vpconfig); + +/* Force update of voltage */ + vpconfig |=VP_FORCEUPDATE ; +voltage_write_reg (vp_reg[vdd].vp_offs.vpconfig_reg, vpconfig); + + timeout =0 ; +/* +* Wait for TransactionDone. Typical latency is <200us. +* Depends on SMPSWAITTIMEMIN/MAX and voltage change +*/ +omap_test_timeout ((prm_read_mod_reg (OCP_MOD ,PRM_IRQSTATUS_REG_OFFSET ) & + vp_reg[vdd].vp_tranxdone_status), +VP_TRANXDONE_TIMEOUT , timeout); + +if (timeout >=VP_TRANXDONE_TIMEOUT ) +pr_warning ("VP%d TRANXDONE timeout exceeded. TRANXDONE never \ +got set after the voltage update.Serious error!!!!\n" , + vdd); + +/* Wait for voltage to settle with SW wait-loop */ + smps_delay = ((smps_steps *125 ) /40 ) +2 ; +udelay (smps_delay); + +/* +* Disable TransactionDone interrupt , clear all status, clear +* control registers +*/ + timeout =0 ; +while (timeout++ <VP_TRANXDONE_TIMEOUT ) { +prm_write_mod_reg (vp_reg[vdd].vp_tranxdone_status, +OCP_MOD ,PRM_IRQSTATUS_REG_OFFSET ); +if (!(prm_read_mod_reg (OCP_MOD ,PRM_IRQSTATUS_REG_OFFSET ) & + vp_reg[vdd].vp_tranxdone_status)) +break ; +udelay (1 ); + } +if (timeout >=VP_TRANXDONE_TIMEOUT ) +pr_warning ("VP%d TRANXDONE timeout exceeded while trying to \ +clear the TRANXDONE status\n" , vdd); + + vpconfig =voltage_read_reg (vp_reg[vdd].vp_offs.vpconfig_reg); +/* Clear initVDD copy trigger bit */ + vpconfig &= ~VP_CONFIG_INITVDD ; +voltage_write_reg (vp_reg[vdd].vp_offs.vpconfig_reg, vpconfig); +/* Clear force bit */ + vpconfig &= ~VP_FORCEUPDATE ; +voltage_write_reg (vp_reg[vdd].vp_offs.vpconfig_reg, vpconfig); + +return true; +}static void __init init_voltageprocessors (void ) {
@@ -586,7 +723,9 @@ void omap_voltageprocessor_enable(int vp_id)* This latching is required only if VC bypass method is used for * voltage scaling during dvfs. */ -vp_latch_vsel (vp_id); +if (!voltscale_vpforceupdate) +vp_latch_vsel (vp_id); + vpconfig =voltage_read_reg (vp_reg[vp_id].vp_offs.vpconfig_reg);/* Enable VP */ voltage_write_reg(vp_reg[vp_id].vp_offs.vpconfig_reg,
@@ -638,11 +777,12 @@ void omap_voltageprocessor_disable(int vp_id)*/ int omap_voltage_scale (int vdd,unsigned long target_volt,unsigned long current_volt) -{/* -* TODO add VP force update method of voltage scaling -* and choose btw the two -*/ -return vc_bypass_scale_voltage (vdd, target_volt, current_volt); +{ +if (voltscale_vpforceupdate) +return vp_forceupdate_scale_voltage (vdd, target_volt, + current_volt); +else +return vc_bypass_scale_voltage (vdd, target_volt, current_volt); }/**
@@ -679,6 +819,29 @@ void omap_reset_voltage(int vdd) }/** +* omap_change_voltscale_method : API to change the voltage scaling method. +* @voltscale_method : the method to be used for voltage scaling. +* +* This API can be used by the board files to change the method of voltage +* scaling between vpforceupdate and vcbypass. The parameter values are +* defined in voltage.h +*/ +void omap_change_voltscale_method (int voltscale_method) +{ +switch (voltscale_method) { +case VOLTSCALE_VPFORCEUPDATE : + voltscale_vpforceupdate = true; +return ; +case VOLTSCALE_VCBYPASS : + voltscale_vpforceupdate = false; +return ; +default : +pr_warning ("Trying to change the method of voltage scaling \ +to an unsupported one!\n" ); + } +} + +/** * omap3_pm_init_vc - polpulates vc_config with values specified in board file * @setup_vc - the structure with various vc parameters *
arch/arm/mach-omap2/voltage.h +3 -0
@@ -14,7 +14,10 @@#define VDD1 0#define VDD2 1 +#define VOLTSCALE_VPFORCEUPDATE 1 +#define VOLTSCALE_VCBYPASS 2 +#define PRM_IRQSTATUS_REG_OFFSET OMAP3_PRM_IRQSTATUS_MPU_OFFSET/* Generic VP definitions. Need to be redefined for OMAP4 */ #define VP_CONFIG_TIMEOUTEN OMAP3430_TIMEOUTEN#define VP_CONFIG_INITVDD OMAP3430_INITVDD
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 21/22 OMAP3: PM: Enabling Smartreflex Class 3 driver by default in pm defconfig
This patch enables smartreflex class 3 driver in omap3_pm_defconfig.
--- arch/arm/configs/omap3_pm_defconfig | 1 + 1 files changed, 1 insertions(+), 0 deletions(-)
arch/arm/configs/omap3_pm_defconfig +1 -0
@@ -246,6 +246,7 @@ CONFIG_ARCH_OMAP4=y # OMAP Feature Selections # CONFIG_OMAP_SMARTREFLEX=y +CONFIG_OMAP_SMARTREFLEX_CLASS3=y # CONFIG_OMAP_SMARTREFLEX_TESTING is not set CONFIG_OMAP_RESET_CLOCKS=y CONFIG_OMAP_MUX=y
Signature · 1 line
1.7.0.rc1.33.g07cf0f
PATCH v3 22/22 OMAP3: PM: Fix crash when enabling SmartReflex on non-supported OMAPs.
This patch renames is_sr_reset to is_sr_enable and sets and unsets this flag in appropriate places so that trying to enable smart reflex in a non-supported OMAP chip does not lead to unnecessary crash. Basically today if sr_enable fails, sr_disable will crash due to accessing sr registers when sr clocks are not turned on.
By checking on is_sr_reset flag and setting and
unsetting this flag appropriately this crash is fixed in this patch.
--- arch/arm/mach-omap2/smartreflex.c | 93 +++++++++++++++++++------------------ 1 files changed, 47 insertions(+), 46 deletions(-)
arch/arm/mach-omap2/smartreflex.c +47 -46
@@ -41,7 +41,7 @@struct omap_sr {int srid; -int is_sr_reset; +int is_sr_enable;int is_autocomp_active;u32 clk_length;u32 err_weight;
@@ -111,26 +111,6 @@ static struct omap_sr *_sr_lookup(int srid)return sr_info; } -static int sr_clk_enable (struct omap_sr *sr) -{ -struct omap_smartreflex_data *pdata = sr->pdev->dev.platform_data; - -if (pdata->device_enable) - pdata->device_enable (sr->pdev); - -return 0 ; -} - -static void sr_clk_disable (struct omap_sr *sr) -{ -struct omap_smartreflex_data *pdata = sr->pdev->dev.platform_data; - -if (pdata->device_idle) - pdata->device_idle (sr->pdev); - - sr->is_sr_reset =1 ; -} -static irqreturn_t sr_omap_isr (int irq,void *data) {struct omap_sr *sr_info = (struct omap_sr *)data;
@@ -211,11 +191,8 @@ static void sr_start_vddautocomp(struct omap_sr *sr) } sr->is_autocomp_active =1 ; -if (!sr_class->enable (sr->srid)) { +if (!sr_class->enable (sr->srid)) sr->is_autocomp_active =0 ; -if (sr->is_sr_reset ==1 ) -sr_clk_disable (sr); - } }static void sr_stop_vddautocomp (struct omap_sr *sr)
@@ -227,7 +204,6 @@ static void sr_stop_vddautocomp(struct omap_sr *sr)if (sr->is_autocomp_active ==1 ) { sr_class->disable (sr->srid,1 ); -sr_clk_disable (sr); sr->is_autocomp_active =0 ; } }
@@ -314,7 +290,6 @@ void sr_configure_errgen(int srid)sr_modify_reg (sr,ERRCONFIG , (ERRCONFIG_VPBOUNDINTEN ), (ERRCONFIG_VPBOUNDINTEN |ERRCONFIG_VPBOUNDINTST )); - sr->is_sr_reset =0 ; }/**
@@ -366,7 +341,6 @@ void sr_configure_minmax(int srid) (ERRCONFIG_MCUACCUMINTEN |ERRCONFIG_MCUACCUMINTST |ERRCONFIG_MCUVALIDINTEN |ERRCONFIG_MCUVALIDINTST | ERRCONFIG_MCUBOUNDINTEN | ERRCONFIG_MCUBOUNDINTST)); - sr->is_sr_reset =0 ; }/**
@@ -406,8 +380,25 @@ int sr_enable(int srid, unsigned long volt)/* errminlimit is opp dependent and hence linked to voltage */ sr->err_minlimit = volt_data.sr_errminlimit; -/* Enable the clocks and configure SR */ -sr_clk_enable (sr); +/* Enable the clocks */ +if (!sr->is_sr_enable) { +struct omap_smartreflex_data *pdata = + sr->pdev->dev.platform_data; +if (pdata->device_enable) { + pdata->device_enable (sr->pdev); + }else { +pr_warning ("Not able to turn on SR%d clocks during \ +enable. So returning" , sr->srid +1 ); +return false; + } + sr->is_sr_enable =1 ; + } + +/* Check if SR is already enabled. If yes do nothing */ +if (sr_read_reg (sr,SRCONFIG ) &SRCONFIG_SRENABLE ) +return true; + +/* Configure SR */ sr_class->configure (sr->srid);sr_write_reg (sr,NVALUERECIPROCAL , nvalue_reciprocal);
@@ -426,6 +417,7 @@ int sr_enable(int srid, unsigned long volt)void sr_disable (int srid) {struct omap_sr *sr =_sr_lookup (srid); +struct omap_smartreflex_data *pdata;int timeout =0 ;if (!sr) {
@@ -434,10 +426,14 @@ void sr_disable(int srid)return ; } -/* Check if SR is already disabled. If yes do nothing */ -if (!(sr_read_reg (sr,SRCONFIG ) &SRCONFIG_SRENABLE )) +/* Check if SR clocks are already disabled. If yes do nothing */ +if (!sr->is_sr_enable)return ; +/* Check if SR is already disabled. If yes just disable the clocks */ +if (!(sr_read_reg (sr,SRCONFIG ) &SRCONFIG_SRENABLE )) + goto disable_clocks; +/* Enable MCUDisableAcknowledge interrupt */ sr_modify_reg (sr,ERRCONFIG ,ERRCONFIG_MCUDISACKINTEN ,ERRCONFIG_MCUDISACKINTEN );
@@ -467,6 +463,17 @@ void sr_disable(int srid)*/ sr_modify_reg (sr,ERRCONFIG ,ERRCONFIG_MCUDISACKINTEN ,ERRCONFIG_MCUDISACKINTST ); + +disable_clocks: + pdata = sr->pdev->dev.platform_data; +if (pdata->device_idle) { + pdata->device_idle (sr->pdev); + }else { +pr_warning ("Unable to turn off SR%d clocks during SR disable" , + srid); +return ; + } + sr->is_sr_enable =0 ; }/**
@@ -489,17 +496,15 @@ void omap_smartreflex_enable(int srid)return ; } +if (!sr->is_autocomp_active) +return ; +if (!sr_class || !(sr_class->enable) || !(sr_class->configure)) {pr_warning ("smartreflex class driver not registered\n" );return ; } -if (sr->is_autocomp_active ==1 ) { -if (sr->is_sr_reset ==1 ) { -if (!sr_class->enable (srid)) -sr_clk_disable (sr); - } - } + sr_class->enable (srid); }/**
@@ -525,18 +530,15 @@ void omap_smartreflex_disable(int srid, int is_volt_reset)return ; } +if (!sr->is_autocomp_active) +return ; +if (!sr_class || !(sr_class->disable)) {pr_warning ("smartreflex class driver not registered\n" );return ; } -if (sr->is_autocomp_active ==1 ) { -if (sr->is_sr_reset ==0 ) { - sr_class->disable (srid, is_volt_reset); -/* Disable SR clk */ -sr_clk_disable (sr); - } - } + sr_class->disable (srid, is_volt_reset); }/**
@@ -615,7 +617,6 @@ static int __devinit omap_smartreflex_probe(struct platform_device *pdev)return -ENOMEM ; sr_info->pdev = pdev; sr_info->srid = pdev->id; - sr_info->is_sr_reset =1 , sr_info->is_autocomp_active =0 ; sr_info->clk_length =0 ;if (odev->hwmods[0 ]->mpu_irqs)
Signature · 1 line
1.7.0.rc1.33.g07cf0f
Re: [PATCHv3 20/22] OMAP3: PM: VP force update method of voltage scaling
In reply to Thara GopinathQuoted 6 lines · Thara Gopinath
This patch introduces VP force update method of voltage scaling and enables it by default. The older method of vc bypass is now configuratble through a menu config option. VP force update is the hardware recommended method of voltage scaling.
Signed-off-by Thara Gopinath <[email protected]>
Hi Thara,
Could you (re) test this along with my changes to the PRCM IRQ handler:
https://patchwork.kernel.org/patch/95450/
I made a change (suggested by Mike Turquette) that affects how that ISR clears PRCM interrupts. Previously, it would possibly interfere with events you're polling for here, but it may never have seen.
[...]
arch/arm/mach-omap2/voltage.h line 20
Quoted 12 lines
arch/arm/mach-omap2/voltage.h +3
-0@@ -14,7 +14,10 @@#define VDD1 0#define VDD2 1 +#define VOLTSCALE_VPFORCEUPDATE 1 +#define VOLTSCALE_VCBYPASS 2 +#define PRM_IRQSTATUS_REG_OFFSET OMAP3_PRM_IRQSTATUS_MPU_OFFSET
Don't use another #define, just use OMAP3_PRM_IRQSTATUS_MPU_OFFSET in code directly Please.
Kevin
Re: [PATCHv3 20/22] OMAP3: PM: VP force update method of voltage scaling
In reply to Thara GopinathQuoted 4 lines · Thara Gopinath
This patch introduces VP force update method of voltage scaling and enables it by default. The older method of vc bypass is now configuratble through a menu config option. VP force update is the hardware recommended method of voltage scaling.
changelog needs update. It is no longer a menuconfig option.
Kevin
Re: [PATCHv3 18/22] OMAP3: PM: Optional reset of voltage during Smartreflex disable.
In reply to Thara GopinathQuoted 5 lines · Thara Gopinath
Currently whenever smartreflex is disabled the voltage for the particular VDD is reset to the non-smartreflex compensated level. This step is unnecessary during dvfs because anyways in the next couple of steps before re-enabling smartreflex , the voltage level is changed.
Quoted 7 lines
This patch adds the flexibility in the smartreflex framework for the user to specify whether or not a voltage reset is required after disabling of smartrefelx. The smartreflex driver just passes on this info to the smartreflex class driver, which ultimately takes the decision to reset the voltage or not.
Signed-off-by Thara Gopinath <[email protected]>
I don't think this option should be a decision made for each call to omap_smartreflex_[en|dis]able(). Rather it should be an init time option.
Kevin
RE: [PATCHv3 18/22] OMAP3: PM: Optional reset of voltage during Smartreflex disable.
Quoted 22 lines
Quoted 22 lines
-----Original Message-----
From: Kevin Hilman [mailto:[email protected]]
Sent: Wednesday, April 28, 2010 12:45 AM
To: Gopinath, Thara
Cc: [email protected]; [email protected]; Cousson, Benoit; Sripathy, Vishwanath; Sawant, Anand
Subject: Re: [PATCHv3 18/22] OMAP3: PM: Optional reset of voltage during Smartreflex disable.Quoted 11 lines · Thara Gopinath
Currently whenever smartreflex is disabled the voltage for the particular VDD is reset to the non-smartreflex compensated level. This step is unnecessary during dvfs because anyways in the next couple of steps before re-enabling smartreflex , the voltage level is changed.
This patch adds the flexibility in the smartreflex framework for the user to specify whether or not a voltage reset is required after disabling of smartrefelx. The smartreflex driver just passes on this info to the smartreflex class driver, which ultimately takes the decision to reset the voltage or not.
Quoted 5 lines
Quoted 5 lines
Quoted 1 line
Signed-off-by Thara Gopinath <[email protected]>I don't think this option should be a decision made for each call to omap_smartreflex_[en|dis]able(). Rather it should be an init time option.
Hello Kevin,
Why do you say this? Anytime we do a disable of smartreflex auto compensation from user space we need a reset of the voltage is required. During dvfs during smartreflex disable a reset of the voltage is not required. And in both these scenarios it is the same class API that gets called. So the only way for the API to know whether to reset the voltage or not is through this parameter. Also IMHO keeping it parameter based allows more flexibility in the framework for voltage reset.
Regards
Thara
Quoted 2 lines
Quoted 2 lines
Kevin
Re: [PATCHv3 18/22] OMAP3: PM: Optional reset of voltage during Smartreflex disable.
Quoted 26 lines · Thara
Quoted 20 lines
Quoted 20 lines
-----Original Message-----
From: Kevin Hilman [mailto:[email protected]]
Sent: Wednesday, April 28, 2010 12:45 AM
To: Gopinath, Thara
Cc: [email protected]; [email protected]; Cousson, Benoit; Sripathy, Vishwanath; Sawant, Anand
Subject: Re: [PATCHv3 18/22] OMAP3: PM: Optional reset of voltage during Smartreflex disable.Quoted 11 lines · Thara Gopinath
Currently whenever smartreflex is disabled the voltage for the particular VDD is reset to the non-smartreflex compensated level. This step is unnecessary during dvfs because anyways in the next couple of steps before re-enabling smartreflex , the voltage level is changed.
This patch adds the flexibility in the smartreflex framework for the user to specify whether or not a voltage reset is required after disabling of smartrefelx. The smartreflex driver just passes on this info to the smartreflex class driver, which ultimately takes the decision to reset the voltage or not.
Quoted 5 lines
Quoted 5 lines
Quoted 1 line
Signed-off-by Thara Gopinath <[email protected]>I don't think this option should be a decision made for each call to omap_smartreflex_[en|dis]able(). Rather it should be an init time option.
Quoted 8 lines
Why do you say this? Anytime we do a disable of smartreflex auto compensation from user space we need a reset of the voltage is required. During dvfs during smartreflex disable a reset of the voltage is not required. And in both these scenarios it is the same class API that gets called. So the only way for the API to know whether to reset the voltage or not is through this parameter. Also IMHO keeping it parameter based allows more flexibility in the framework for voltage reset.
OK, I see now.
I was looking at this patch in isolation and didn't notice the usage of it in the next DVFS patch where the ->disable is done without reset.
Also, since this new flag is a bool, change it from int to bool.
Or better yet add a new function. One thing I'm not a fan of for readability sake is the use of bool flags. It makes me have to go look at the function to see what the flag is used for. I'd rather just see a new function added. Something like omap_smartreflex_disable_noreset() would make the code a bit more readable.
Thanks,
Kevin
Re: [PATCHv3 17/22] OMAP3: PM: Implement latest h/w recommendations for SR and VP registers and SR VP enable disable sequence.
In reply to Thara GopinathQuoted 7 lines · Thara Gopinath
This patch introduces OMAP3 specific values for Smartreflex and Voltage processor registers as per the latest TI recommendations. This patch adds smartreflex errminlimit and voltage processor errorgain into the voltage tables as they vary with different voltages. This patch also improves the smartreflex and voltage processor enable disable sequences as per the latest recommendations.
Quoted 5 lines
These recommendations were first formed based on experimentations on N900 platform and were implemented in the N900 codebase base first by Nishanth Menon and Paul Walmsley.
Signed-off-by Thara Gopinath <[email protected]>
Some minor CodingStyle issues. Please check the multi-line comment style in this patch.
Kevin
Re: [PATCHv3 15/22] OMAP3: PM: Support for enabling smartreflex autocompensation by default.
In reply to Thara GopinathQuoted 2 lines · Thara Gopinath
This patch adds support to pdata enable smartreflex autocompenstion during init based on
enable_on_initflag passed as pdata.
-ENOPARSE. Removing the first 'pdata' makes it understandable, I think.
Quoted 8 lines
This patch also adds enabling of autocompensation by default (setting
enable_on_initflag to true) in case of ES3.1 OMAP3430 chip. In the current implementation
this step is kept insmartreflex.citself.Later an API can be added so that the decision to enable autocompensation by default can be passed from the corresponding board files.Signed-off-by Thara Gopinath <[email protected]>
otherwise, ok.
Kevin
Re: [PATCHv3 14/22] OMAP3: PM: Configurations for Smartreflex Class 2 and Smartreflex Class 3
In reply to Thara GopinathQuoted 12 lines · Thara Gopinath
There are two separate modules in SmartReflex-AVS :
MinMaxAvg module and Error module. Class3 uses the Error module only. In Class2 you can choose between either module since it is software based. The registers are mapped to the modules as followed:MinMaxAvg module: AccumData, MinMaxAvgEnable, MinMaxAvgValid,
MinMaxAvgAccumValid, SenVal, SenMin, SenMax, SenAverage, AverageWeight, MCUAccum, MCUValid, MCUBounds.Error module: SenNGain, SenPGain, SenPRN, SenNRN, AvgError,
SenError, VPBounds, ErrWeight, ErrMaxLimit, ErrMinLimit.
Quoted 8 lines
Shared between both: SRClkLength, SREnable, SenEnable, SenNEnable,
SenPEnable, DelayCtrl, MCUDisableAck, ClkActivity.This patch generates separate API's to configure the two modules which can be used by the smartreflex class driver as per its requirement. This patch allows allows for registering for smartreflex interrupt handler and notification of interrupts in case requested by the smartreflex class driver.
After just removing functions that take SR IDs, here new functions are added that take SR IDs and do _sr_lookup() instead of passing sr pointer.
Kevin
Re: [PATCHv3 12/22] OMAP3: PM: Minimizing the passing around of sr id in smartreflex.c
In reply to Thara GopinathQuoted 5 lines · Thara Gopinath
This patch ensures that sr id is passed as a parameter only to public APIs in
smartreflex.cand other APIs insmartreflex.cuses theomap_srstrucutres.Signed-off-by Thara Gopinath <[email protected]>
Good change, but...
Quoted 27 lines
--- arch/arm/mach-omap2/smartreflex.c | 36 +++++++++++++----------------------- 1 files changed, 13 insertions(+), 23 deletions(-)arch/arm/mach-omap2/smartreflex.c +1
-9@@ -190,16 +190,8 @@ static void sr_configure(struct omap_sr *sr) sr->is_sr_reset =0 ; } -static void sr_start_vddautocomp (int srid) +static void sr_start_vddautocomp (struct omap_sr *sr) { -struct omap_sr *sr =_sr_lookup (srid); - -if (!sr) { -pr_warning ("omap_sr struct corresponding to SR%d not found\n" , - srid +1 ); -return ; - } -if (!sr_class || !(sr_class->enable)) {pr_warning ("smartreflex class driver not registered\n" );return ;
arch/arm/mach-omap2/smartreflex.c static void sr_start_vddautocomp(int srid) · line 206
Quoted 5 lines
arch/arm/mach-omap2/smartreflex.c +1
-1@@ -211,30 +203,22 @@ static void sr_start_vddautocomp(int srid) } sr->is_autocomp_active =1 ; -if (!sr_class->enable (srid)) { +if (!sr_class->enable (sr->srid)) {
... the class3 layer is still taking SR ID as a parameter and it should also just take an sr_info ptr.
Kevin
RE: [PATCHv3 12/22] OMAP3: PM: Minimizing the passing around of sr id in smartreflex.c
Quoted 48 lines
Quoted 48 lines
-----Original Message-----
From: Kevin Hilman [mailto:[email protected]]
Sent: Wednesday, April 28, 2010 12:32 AM
To: Gopinath, Thara
Cc: [email protected]; [email protected]; Cousson, Benoit; Sripathy, Vishwanath; Sawant, Anand
Subject: Re: [PATCHv3 12/22] OMAP3: PM: Minimizing the passing around of sr id insmartreflex.cQuoted 5 lines · Thara Gopinath
This patch ensures that sr id is passed as a parameter only to public APIs in
smartreflex.cand other APIs insmartreflex.cuses theomap_srstrucutres.Signed-off-by Thara Gopinath <[email protected]>Good change, but...
Quoted 29 lines
--- arch/arm/mach-omap2/smartreflex.c | 36 +++++++++++++----------------------- 1 files changed, 13 insertions(+), 23 deletions(-)arch/arm/mach-omap2/smartreflex.c +1
-9@@ -190,16 +190,8 @@ static void sr_configure(struct omap_sr *sr) sr->is_sr_reset =0 ; } -static void sr_start_vddautocomp (int srid) +static void sr_start_vddautocomp (struct omap_sr *sr) { -struct omap_sr *sr =_sr_lookup (srid); - -if (!sr) { -pr_warning ("omap_sr struct corresponding to SR%d not found\n" , - srid +1 ); -return ; - } -if (!sr_class || !(sr_class->enable)) {pr_warning ("smartreflex class driver not registered\n" );return ;@@ -211,30 +203,22 @@ static void sr_start_vddautocomp(int srid) }
Quoted 6 lines
Quoted 6 lines
arch/arm/mach-omap2/smartreflex.c static void sr_start_vddautocomp(int srid) · line 206
Quoted 3 lines
arch/arm/mach-omap2/smartreflex.c +1
-1sr->is_autocomp_active =1 ; -if (!sr_class->enable (srid)) { +if (!sr_class->enable (sr->srid)) {... the class3 layer is still taking SR ID as a parameter and it should also just take an
sr_infoptr.
Hi Kevin,
sr_info is an internal structure for smartreflex driver. The intention behind this patch is all external API's pass the srid and internally the driver static APIs take sr_info as parameter. I did not realize this point till now when I was doing the actual changes and hence the late reply :-)
Regards
Thara
Quoted 2 lines
Quoted 2 lines
Kevin
Re: [PATCHv3 12/22] OMAP3: PM: Minimizing the passing around of sr id in smartreflex.c
Quoted 11 lines · Thara
Quoted 11 lines
Quoted 11 lines
Quoted 5 lines · Thara Gopinath
This patch ensures that sr id is passed as a parameter only to public APIs in
smartreflex.cand other APIs insmartreflex.cuses theomap_srstrucutres.Signed-off-by Thara Gopinath <[email protected]>Good change, but...
[...]
Quoted 7 lines
Quoted 3 lines
Quoted 3 lines
... the class3 layer is still taking SR ID as a parameter and it should also just take an
sr_infoptr.
sr_infois an internal structure for smartreflex driver. The intention behind this patch is all external API's pass the srid and internally the driver static APIs takesr_infoas parameter.
OK, that makes sense. I though I saw the usage of _sr_lookup() inside the class driver which made me think it should just take sr_info. But looking again now, I see it's only using the id.
Quoted 2 lines
I did not realize this point till now when I was doing the actual changes and hence the late reply :-)
no worries, thanks for clarifying.
Kevin
Re: [PATCHv3 10/22] OMAP3: PM: Adding voltage table support in voltage driver.
In reply to Thara GopinathQuoted 36 lines · Thara Gopinath
This patch introduces the framework to create voltage table per VDD basis in voltage driver. Each VDD will have one voltage table, which in turn will contain one entry per voltage supported and other data associated with the voltage like smartreflex N-target values. This patch also generates voltage tables for VDD1 and VDD2 of OMAP3430 and passes them as
dev_attrtosr_device.cin order to populate the smartreflex n-target values.These voltage tables are extended in a later patch to contain more voltage specific information like errminlimt and errorgain values.
Signed-off-by Thara Gopinath <[email protected]>--- arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 7 +- arch/arm/mach-omap2/smartreflex.c | 27 +-------- arch/arm/mach-omap2/smartreflex.h | 13 +---- arch/arm/mach-omap2/sr_device.c | 42 ++---------- arch/arm/mach-omap2/voltage.c | 93 +++++++++++++++++++++++++++- arch/arm/mach-omap2/voltage.h | 15 +++++ 6 files changed, 118 insertions(+), 79 deletions(-)arch/arm/mach-omap2/omap_hwmod_3xxx_data.c +1
-0@@ -23,6 +23,7 @@#include "prm-regbits-34xx.h" #include "smartreflex.h" +#include "voltage.h" /* * OMAP3xxx hardware module integration data @@ -240,14 +241,13 @@ static u32 omap34xx_sr1_test_nvalues[] = { };
arch/arm/mach-omap2/omap_hwmod_3xxx_data.c static u32 omap34xx_sr1_test_nvalues[] = { · line 250
Quoted 10 lines
arch/arm/mach-omap2/omap_hwmod_3xxx_data.c +1
-2static struct omap_smartreflex_dev_data omap34xx_sr1_dev_attr = { - .volts_supported =5 , .efuse_sr_control =OMAP343X_CONTROL_FUSE_SR , .sennenable_shift =OMAP343X_SR1_SENNENABLE_SHIFT , .senpenable_shift =OMAP343X_SR1_SENPENABLE_SHIFT , .efuse_nvalues_offs = omap34xx_sr1_efuse_offs, .test_sennenable =0x3 , .test_senpenable =0x3 , - .test_nvalues = omap34xx_sr1_test_nvalues + .test_nvalues = omap34xx_sr1_test_nvalues,
unrelated change, should be in original patch that adds this struct.
Quoted 6 lines
arch/arm/mach-omap2/omap_hwmod_3xxx_data.c +0
-0};static struct omap_hwmod omap34xx_sr1_hwmod = {@@ -276,14 +276,13 @@ static u32 omap34xx_sr2_test_nvalues[] = { };
arch/arm/mach-omap2/omap_hwmod_3xxx_data.c static u32 omap34xx_sr2_test_nvalues[] = { · line 285
Quoted 10 lines
arch/arm/mach-omap2/omap_hwmod_3xxx_data.c +1
-2static struct omap_smartreflex_dev_data omap34xx_sr2_dev_attr = { - .volts_supported =3 , .efuse_sr_control =OMAP343X_CONTROL_FUSE_SR , .sennenable_shift =OMAP343X_SR2_SENNENABLE_SHIFT , .senpenable_shift =OMAP343X_SR2_SENPENABLE_SHIFT , .efuse_nvalues_offs = omap34xx_sr2_efuse_offs, .test_sennenable =0x3 , .test_senpenable =0x3 , - .test_nvalues = omap34xx_sr2_test_nvalues + .test_nvalues = omap34xx_sr2_test_nvalues,
ditto
Quoted 2 lines
arch/arm/mach-omap2/omap_hwmod_3xxx_data.c +0
-0};
[...]
Quoted 13 lines
/**
+ *omap_get_voltage_table: API to get the voltage table associated with a
+ * particular voltage domain.
+ *
+ * @vdd : the voltage domain id for which the voltage table is required
+ * @volt_data : the voltage table for the particular vdd which is to be
+ * populated by this API
+ * @volt_count : number of distinct voltages supported by this vdd which
+ * is to be populated by this API.
+ *
+ * This API populates the voltage table associated with a VDD and the count
+ * of number of voltages supported into the passed parameter pointers.
+ */
arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
Quoted 6 lines
arch/arm/mach-omap2/omap_hwmod_3xxx_data.c +6
-0+void omap_get_voltage_table (int vdd,struct omap_volt_data **volt_data, +int *volt_count) +{ + *volt_data = vp_reg[vdd].volt_data; + *volt_count = vp_reg[vdd].volt_data_count; +}
How about returning the count instad of in another pointer.
Quoted 46 lines
arch/arm/mach-omap2/omap_hwmod_3xxx_data.c +36
-0+/** +* omap_match_volt : API to get the voltage table entry for a particular +* voltage +* @vdd : the voltage domain id for whose voltage table has to be searched +* @volt : the voltage to be searched in the voltage table +* @volt_data : the matching voltage table entry which has to be populate +* by this API. +* +* This API searches through the voltage table for the required voltage +* domain and tries to find a matching entry for the passed voltage volt. +* If a matching entry is found volt_data is populated with that entry. +* Returns -ENXIO if not voltage table exisits for the passed voltage +* domain or if there is no matching entry. On success returns true. +*/ +int omap_match_volt (int vdd,unsigned long volt, +struct omap_volt_data *volt_data) +{ +int i; + +if (!vp_reg[vdd].volt_data) { +pr_notice ("voltage table does not exist for VDD %d\n" , vdd +1 ); +return -ENXIO ; + } + +for (i =0 ; i < vp_reg[vdd].volt_data_count; i++) { +if (vp_reg[vdd].volt_data[i].voltage == volt) { + *volt_data = vp_reg[vdd].volt_data[i]; +return 0 ; + } + } +pr_notice ("Unable to match the current voltage with \ +the voltage table for VDD %d\n" , vdd +1 ); +return -ENXIO ; +} + +/** * omap_voltage_init : Volatage init API which does VP and VC init. */ void __init omap_voltage_init (void )arch/arm/mach-omap2/voltage.h +0
-0@@ -63,6 +63,17 @@/* TODO OMAP4 VP register values if the same file is used for OMAP4*/
arch/arm/mach-omap2/voltage.h line 74
Quoted 10 lines
arch/arm/mach-omap2/voltage.h +9
-0+/** +* omap_volt_data - Omap voltage specific data. +* +* @voltage : The possible voltage value +* @sr_nvalue : Smartreflex N target value at voltage <voltage> +*/ +struct omap_volt_data { +unsigned long voltage; +u32 sr_nvalue;
both could be unsigned long (or u32)
Quoted 6 lines
arch/arm/mach-omap2/voltage.h +2
-0+}; +void omap_voltageprocessor_enable (int vp_id);void omap_voltageprocessor_disable (int vp_id);void omap_voltage_init_vc (struct prm_setup_vc *setup_vc);
arch/arm/mach-omap2/voltage.h void omap_voltage_init(void); · line 89
Quoted 9 lines
arch/arm/mach-omap2/voltage.h +4
-0@@ -70,5 +81,9 @@ void omap_voltage_init(void);int omap_voltage_scale (int vdd,unsigned long target_volt,unsigned long current_volt);void omap_reset_voltage (int vdd); +void omap_get_voltage_table (int vdd,struct omap_volt_data **volt_data, +int *volt_count); +int omap_match_volt (int vdd,unsigned long volt, +struct omap_volt_data *volt_data);unsigned long get_curr_vdd1_voltage (void );unsigned long get_curr_vdd2_voltage (void );
Kevin
Re: [PATCHv3 05/22] OMAP3: PM: Remove OPP id dependency from smartreflex driver
In reply to Thara GopinathQuoted 50 lines · Thara Gopinath
This patch removes
get_vdd1_oppandget_vdd2_oppAPI's and replaces them withget_curr_vdd1_voltageandget_curr_vdd2_voltageAPI's. N-target values are now linked to voltages and the link bewtween voltage and n-target values is managed internally in smartreflex driver andsr_devices.c.
get_curr_vdd1_voltageandget_curr_vdd2_voltageare added in smartreflex driver in this patch. These API's will be moved to the voltage driver in a later patch when voltage specific code is separated out of smartreflex. The link between various voltages and n-target values will also be separated out later.Signed-off-by Thara Gopinath <[email protected]>--- arch/arm/mach-omap2/smartreflex.c | 201 +++++++++++++++---------------------- arch/arm/mach-omap2/smartreflex.h | 21 +++- arch/arm/mach-omap2/sr_device.c | 39 ++++++- 3 files changed, 129 insertions(+), 132 deletions(-)arch/arm/mach-omap2/smartreflex.c +2
-9@@ -48,7 +48,6 @@ struct omap_sr {int srid;int is_sr_reset;int is_autocomp_active; -struct clk *vdd_opp_clk;u32 clk_length;unsigned int irq;struct platform_device *pdev;@@ -119,64 +118,65 @@ static void sr_clk_disable(struct omap_sr *sr) sr->is_sr_reset =1 ; } -static u8 get_vdd1_opp (void ) +static unsigned long get_curr_vdd1_voltage (void ) {struct omap_opp *opp;unsigned long freq; -struct omap_sr *sr_info =_sr_lookup (SR1 ); +struct clk *dpll1_clk; -if (!sr_info) { -pr_warning ("omap_sr struct corresponding to SR1 not found\n" ); -return 0 ; - } - -if (sr_info->vdd_opp_clk ==NULL ||IS_ERR (sr_info->vdd_opp_clk))
arch/arm/mach-omap2/smartreflex.c static void sr_clk_disable(struct omap_sr *sr) · line 135
Quoted 10 lines
arch/arm/mach-omap2/smartreflex.c +4
-2+ dpll1_clk =clk_get (NULL ,"dpll1_ck" ); +if (IS_ERR (dpll1_clk))return 0 ; - freq = sr_info->vdd_opp_clk->rate; - opp =opp_find_freq_ceil (OPP_MPU , &freq); + freq = dpll1_clk->rate;; + opp =opp_find_freq_exact (OPP_MPU , freq,1 );if (IS_ERR (opp))return 0 ;
I mentioned this in an earlier review, but I think it's best to leave the clock as part of sr_info. If you also add the OPP enum value to sr_info, you could have a single, common function to get current voltage intstead of a separate one per-VDD. Otherwise, as additional voltage domains are added, we need to add another function.
What should result is just a single get_curr_voltage() or similar which takes an sr_info ptr and doesn't need to sr_lookup()
arch/arm/mach-omap2/smartreflex.c static void sr_clk_disable(struct omap_sr *sr) · line 135
Quoted 8 lines
arch/arm/mach-omap2/smartreflex.c +0
-7-/* -* Use higher freq voltage even if an exact match is not available -* we are probably masking a clock framework bug, so warn -*/ -if (unlikely (freq != sr_info->vdd_opp_clk->rate)) -pr_warning ("%s: Available freq %ld != dpll freq %ld.\n" , - __func__, freq, sr_info->vdd_opp_clk->rate);
Removed here, but added back in subsequent patch. Should be combined. Another reason to start condensing this series and reworking against mainline.
Quoted 41 lines
arch/arm/mach-omap2/smartreflex.c +9
-19-return opp_get_opp_id (opp); +return opp_get_voltage (opp); } -static u8 get_vdd2_opp (void ) +static unsigned long get_curr_vdd2_voltage (void ) {struct omap_opp *opp;unsigned long freq; -struct omap_sr *sr_info =_sr_lookup (SR2 ); +struct clk *l3_clk; -if (!sr_info) { -pr_warning ("omap_sr struct corresponding to SR2 not found\n" ); -return 0 ; - } - -if (sr_info->vdd_opp_clk ==NULL ||IS_ERR (sr_info->vdd_opp_clk)) + l3_clk =clk_get (NULL ,"l3_ick" ); +if (IS_ERR (l3_clk))return 0 ; - freq = sr_info->vdd_opp_clk->rate; - opp =opp_find_freq_ceil (OPP_L3 , &freq); + freq = l3_clk->rate; + opp =opp_find_freq_exact (OPP_L3 , freq,1 );if (IS_ERR (opp))return 0 ; -/* -* Use higher freq voltage even if an exact match is not available -* we are probably masking a clock framework bug, so warn -*/ -if (unlikely (freq != sr_info->vdd_opp_clk->rate)) -pr_warning ("%s: Available freq %ld != dpll freq %ld.\n" , - __func__, freq, sr_info->vdd_opp_clk->rate); -return opp_get_opp_id (opp); +return opp_get_voltage (opp); } +static int sr_match_volt(struct omap_sr *sr, unsigned long volt,
arch/arm/mach-omap2/smartreflex.c static void sr_clk_disable(struct omap_sr *sr) · line 167
Quoted 10 lines
arch/arm/mach-omap2/smartreflex.c +10
-0+ struct omap_volt_data *volt_data) +{ +struct omap_smartreflex_data *pdata = sr->pdev->dev.platform_data; +struct omap_device *odev =to_omap_device (sr->pdev); +struct omap_smartreflex_dev_data *sr_dev_data = + odev->hwmods[0 ]->dev_attr; +int i; + +if (!pdata->sr_volt_data) { +pr_notice ("voltage table does not exist for SR %d\n" , sr->srid);
dev_notice()
arch/arm/mach-omap2/smartreflex.c static void sr_clk_disable(struct omap_sr *sr) · line 177
Quoted 10 lines
arch/arm/mach-omap2/smartreflex.c +10
-0+return false; + } +for (i =0 ; i < sr_dev_data->volts_supported; i++) { +if (pdata->sr_volt_data[i].voltage == volt) { + *volt_data = pdata->sr_volt_data[i]; +return true; + } + } +pr_notice ("Unable to match the current voltage with \ +the voltage table for SR %d\n" , sr->srid);
dev_notice()
Quoted 3 lines
arch/arm/mach-omap2/smartreflex.c +2
-0+return false; +}
[...]
Quoted 23 lines
arch/arm/mach-omap2/smartreflex.h +11
-0@@ -242,6 +242,17 @@ extern u32 current_vdd2_opp;#endif /** +* omap_volt_data - Omap voltage specific data. +* +* @voltage : The possible voltage value +* @sr_nvalue : Smartreflex N target value at voltage <voltage> +*/ +struct omap_volt_data { +unsigned long voltage; +u32 sr_nvalue; +}; + +/** * omap_smartreflex_dev_data - Smartreflex device specific data * * @volts_supported : Number of distinct voltages possible for the VDD
arch/arm/mach-omap2/smartreflex.h struct omap_smartreflex_dev_data { · line 311
Quoted 10 lines
arch/arm/mach-omap2/smartreflex.h +3
-4@@ -295,10 +306,10 @@ struct omap_smartreflex_dev_data {* @device_idle : fn pointer to be pouplated with omap_device idle API */ struct omap_smartreflex_data { -u32 senp_mod; -u32 senn_mod; -u32 *sr_nvalue; -bool enable_on_init; +u32 senp_mod; +u32 senn_mod; +struct omap_volt_data *sr_volt_data;
minor nit: drop the sr_ prefix
Quoted 71 lines
arch/arm/mach-omap2/smartreflex.h +2
-1+bool enable_on_init;int (*device_enable)(struct platform_device *pdev);int (*device_shutdown)(struct platform_device *pdev);int (*device_idle)(struct platform_device *pdev);@@ -307,7 +318,7 @@ struct omap_smartreflex_data {void enable_smartreflex (int srid);void disable_smartreflex (int srid);int sr_voltagescale_vcbypass (u32 t_opp,u32 c_opp,u8 t_vsel,u8 c_vsel); -void sr_start_vddautocomap (int srid,u32 target_opp_no); +void sr_start_vddautocomap (int srid,unsigned long volt);int sr_stop_vddautocomap (int srid);#else static inline void enable_smartreflex (int srid) {}arch/arm/mach-omap2/sr_device.c +20
-6@@ -51,8 +51,9 @@ static void __init sr_read_efuse( !dev_data->efuse_nvalues_offs))return ; - sr_data->sr_nvalue =kzalloc (sizeof (sr_data->sr_nvalue) * - dev_data->volts_supported ,GFP_KERNEL ); +if (WARN_ON (!sr_data->sr_volt_data)) +return ; + sr_data->senn_mod = (omap_ctrl_readl (dev_data->efuse_sr_control) & (0x3 << dev_data->sennenable_shift) >> dev_data->sennenable_shift);@@ -60,7 +61,7 @@ static void __init sr_read_efuse( (0x3 << dev_data->senpenable_shift) >> dev_data->senpenable_shift);for (i =0 ; i < dev_data->volts_supported; i++) - sr_data->sr_nvalue[i] =omap_ctrl_readl ( + sr_data->sr_volt_data[i].sr_nvalue =omap_ctrl_readl ( dev_data->efuse_nvalues_offs[i]); }@@ -78,12 +79,13 @@ static void __init sr_set_testing_nvalues( !dev_data->test_nvalues))return ; - sr_data->sr_nvalue =kzalloc (sizeof (sr_data->sr_nvalue) * - dev_data->volts_supported ,GFP_KERNEL ); +if (WARN_ON (!sr_data->sr_volt_data)) +return ; + sr_data->senn_mod = dev_data->test_sennenable; sr_data->senp_mod = dev_data->test_senpenable;for (i =0 ; i < dev_data->volts_supported; i++) - sr_data->sr_nvalue[i] = dev_data->test_nvalues[i]; + sr_data->sr_volt_data[i].sr_nvalue = dev_data->test_nvalues[i]; } static void __init sr_set_nvalues(struct omap_smartreflex_dev_data *dev_data,@@ -97,6 +99,28 @@ static void __init sr_set_nvalues(struct omap_smartreflex_dev_data *dev_data, } } +static void __init omap34xx_sr_volt_details (struct omap_smartreflex_data + *sr_data,int srid, +int volt_count) +{ + sr_data->sr_volt_data =kzalloc (sizeof (sr_data->sr_volt_data) * + volt_count ,GFP_KERNEL ); +if (WARN_ON (!sr_data->sr_volt_data)) +return ; + +if (srid ==SR1 ) { + sr_data->sr_volt_data[0 ].voltage =975000 ; + sr_data->sr_volt_data[1 ].voltage =1075000 ;
arch/arm/mach-omap2/sr_device.c static void __init sr_set_nvalues(struct omap_smartreflex_dev_data *dev_data, · line 123
Quoted 10 lines
arch/arm/mach-omap2/sr_device.c +10
-0+ sr_data->sr_volt_data[2 ].voltage =1200000 ; + sr_data->sr_volt_data[3 ].voltage =1270000 ; + sr_data->sr_volt_data[4 ].voltage =1350000 ; + }else if (srid ==SR2 ) { + sr_data->sr_volt_data[0 ].voltage =975000 ; + sr_data->sr_volt_data[1 ].voltage =1050000 ; + sr_data->sr_volt_data[2 ].voltage =1150000 ; + } +} +
again, more stuff added that is removed later. Time to start condensing as it's getting hard to keep track of.
[...]
Kevin
Re: [PATCHv3 04/22] OMAP3: PM: Move smartreflex autocompensation enable disable hooks to PM debugfs.
In reply to Thara GopinathQuoted 9 lines · Thara Gopinath
This patch moves the hooks to enable disable smartreflex autocompensation to pm debugfs from the
/sys/power/.To enable autocompensation for smartreflex SR<n> do
echo 1 > <path>/pm_debug/sr<n>_autocomp To disable autocompensation for smartreflex SR<n> do echo 0 > <path>/pm_debug/sr<n>_autocompSigned-off-by Thara Gopinath <[email protected]>
some minor comments...
Quoted 54 lines
--- arch/arm/mach-omap2/pm-debug.c | 4 +- arch/arm/mach-omap2/smartreflex.c | 114 ++++++++++-------------------------- arch/arm/mach-omap2/smartreflex.h | 2 + 3 files changed, 36 insertions(+), 84 deletions(-)arch/arm/mach-omap2/pm-debug.c +2
-2@@ -162,7 +162,7 @@ void omap2_pm_dump(int mode, int resume, unsigned int us)static void pm_dbg_regset_store (u32 *ptr); -struct dentry *pm_dbg_dir; +struct dentry *pm_dbg_dir, *pm_dbg_main_dir;static int pm_dbg_init_done;@@ -613,7 +613,7 @@ static int __init pm_dbg_init(void)S_IRUGO |S_IWUGO , d, &voltage_off_while_idle, &pm_dbg_option_fops); - + pm_dbg_main_dir = d; pm_dbg_init_done =1 ;return 0 ;arch/arm/mach-omap2/smartreflex.c +2
-1@@ -24,11 +24,11 @@#include <linux/delay.h> #include <linux/err.h> #include <linux/clk.h> -#include <linux/sysfs.h> #include <linux/kobject.h> #include <linux/i2c/twl.h> #include <linux/io.h> #include <linux/list.h> +#include <linux/debugfs.h> #include <plat/omap34xx.h> #include <plat/clock.h> @@ -42,6 +42,7 @@#include "prm-regbits-34xx.h" #define MAX_TRIES 100 +#define SMARTREFLEX_NAME_LEN 16struct omap_sr {int srid;
arch/arm/mach-omap2/smartreflex.c int sr_voltagescale_vcbypass(u32 target_opp, u32 current_opp, · line 800
Quoted 7 lines
arch/arm/mach-omap2/smartreflex.c +1
-3@@ -796,103 +797,53 @@ int sr_voltagescale_vcbypass(u32 target_opp, u32 current_opp,return 0 ; } -/* Sysfs interface to select SR VDD1 auto compensation */ -static ssize_t omap_sr_vdd1_autocomp_show (struct kobject *kobj, -struct kobj_attribute *attr,char *buf) +/* PM Debug Fs enteries to enable disable smartreflex.*/
^
need a space before the */
arch/arm/mach-omap2/smartreflex.c int sr_voltagescale_vcbypass(u32 target_opp, u32 current_opp, · line 801
Quoted 1 line
arch/arm/mach-omap2/smartreflex.c +1
-0+
stray blank line
arch/arm/mach-omap2/smartreflex.c int sr_voltagescale_vcbypass(u32 target_opp, u32 current_opp, · line 804
Quoted 4 lines
arch/arm/mach-omap2/smartreflex.c +2
-1+static int omap_sr_autocomp_show (void *data,u64 *val) { -struct omap_sr *sr_info =_sr_lookup (SR1 ); +struct omap_sr *sr_info = (struct omap_sr *) data;
struct device *dev = &sr_info->pdev->dev;
arch/arm/mach-omap2/smartreflex.c int sr_voltagescale_vcbypass(u32 target_opp, u32 current_opp, · line 808
Quoted 4 lines
arch/arm/mach-omap2/smartreflex.c +2
-1if (!sr_info) { -pr_warning ("omap_sr struct corresponding to SR1 not found\n" ); +pr_warning ("omap_sr struct corresponding to SR%d not found\n" , + sr_info->srid);
dev_err(dev, "struct for SR%d not found\n",
sr_info->srid);
Quoted 42 lines
arch/arm/mach-omap2/smartreflex.c +3
-34return 0 ; } -return sprintf (buf,"%d\n" , sr_info->is_autocomp_active); + *val = sr_info->is_autocomp_active; +return 0 ; } -static ssize_t omap_sr_vdd1_autocomp_store (struct kobject *kobj, -struct kobj_attribute *attr, -const char *buf,size_t n) +static int omap_sr_autocomp_store (void *data,u64 val) { -unsigned short value; - -if (sscanf (buf,"%hu" , &value) !=1 || (value >1 )) { -pr_err ("sr_vdd1_autocomp: Invalid value\n" ); -return -EINVAL ; - } - -if (value ==0 ) { -sr_stop_vddautocomap (SR1 ); - }else { -u32 current_vdd1opp_no =get_vdd1_opp (); -if (!current_vdd1opp_no) { -pr_err ("sr_vdd1_autocomp: Current VDD1 opp unknown\n" ); -return -EINVAL ; - } -sr_start_vddautocomap (SR1 , current_vdd1opp_no); - } -return n; -} - -static struct kobj_attribute sr_vdd1_autocomp = { - .attr = { - .name =__stringify (sr_vdd1_autocomp), - .mode =0644 , - }, - .show = omap_sr_vdd1_autocomp_show, - .store = omap_sr_vdd1_autocomp_store, -}; - -/* Sysfs interface to select SR VDD2 auto compensation */
arch/arm/mach-omap2/smartreflex.c int sr_voltagescale_vcbypass(u32 target_opp, u32 current_opp, · line 821
Quoted 10 lines
arch/arm/mach-omap2/smartreflex.c +3
-5-static ssize_t omap_sr_vdd2_autocomp_show (struct kobject *kobj, -struct kobj_attribute *attr,char *buf) -{ -struct omap_sr *sr_info =_sr_lookup (SR2 ); +struct omap_sr *sr_info = (struct omap_sr *) data;if (!sr_info) { -pr_warning ("omap_sr struct corresponding to SR2 not found\n" ); +pr_warning ("omap_sr struct corresponding to SR%d not found\n" , + sr_info->srid);
dev_warn()
arch/arm/mach-omap2/smartreflex.c int sr_voltagescale_vcbypass(u32 target_opp, u32 current_opp, · line 822
Quoted 5 lines
arch/arm/mach-omap2/smartreflex.c +0
-3return 0 ; } -return sprintf (buf,"%d\n" , sr_info->is_autocomp_active); -} -
[...]
Kevin
Re: [PATCHv3 03/22] OMAP3: PM: Convert smartreflex driver into a platform driver using hwmods and omap-device layer
In reply to Thara GopinathQuoted 67 lines · Thara Gopinath
This patch converts the exisitng smartreflex library into a platform driver with device , driver registrations using hardware mods. As part of this Ntarget values are passed as platform data.
Signed-off-by Thara Gopinath <[email protected]>--- arch/arm/mach-omap2/Makefile | 2 +- arch/arm/mach-omap2/smartreflex.c | 325 +++++++++++++------------------------ arch/arm/mach-omap2/smartreflex.h | 26 +++ arch/arm/mach-omap2/sr_device.c | 139 ++++++++++++++++ 4 files changed, 278 insertions(+), 214 deletions(-) create mode 100644 arch/arm/mach-omap2/sr_device.carch/arm/mach-omap2/Makefile +1
-1@@ -48,7 +48,7 @@ obj-$(CONFIG_ARCH_OMAP2) += pm24xx.o obj-$(CONFIG_ARCH_OMAP2) += sleep24xx.o obj-$(CONFIG_ARCH_OMAP3) += pm34xx.o sleep34xx.o cpuidle34xx.o obj-$(CONFIG_PM_DEBUG) += pm-debug.o -obj-$(CONFIG_OMAP_SMARTREFLEX) += smartreflex.o +obj-$(CONFIG_OMAP_SMARTREFLEX) += sr_device.o smartreflex.o AFLAGS_sleep24xx.o :=-Wa,-march=armv6 AFLAGS_sleep34xx.o :=-Wa,-march=armv7-aarch/arm/mach-omap2/smartreflex.c +5
-3@@ -3,6 +3,9 @@* * OMAP34XX SmartReflex Voltage Control * +* Copyright (C) 2010 Texas Instruments, Inc. +* Thara Gopinath <[email protected]> +* * Copyright (C) 2008 Nokia Corporation * Kalle Jokiniemi * @@ -14,7 +17,6 @@* published by the Free Software Foundation. */ -#include <linux/kernel.h> #include <linux/init.h> #include <linux/interrupt.h> @@ -29,10 +31,11 @@#include <linux/list.h> #include <plat/omap34xx.h> -#include <plat/control.h> #include <plat/clock.h> #include <plat/opp.h> #include <plat/opp_twl_tps.h> +#include <plat/omap_hwmod.h> +#include <plat/omap_device.h> #include "prm.h" #include "smartreflex.h" @@ -41,45 +44,44 @@#define MAX_TRIES 100struct omap_sr { -int srid;
arch/arm/mach-omap2/smartreflex.c line 54
Quoted 10 lines
arch/arm/mach-omap2/smartreflex.c +0
-10-int is_sr_reset; -int is_autocomp_active; -struct clk *clk; -struct clk *vdd_opp_clk; -u32 clk_length; -u32 req_opp_no; -u32 opp1_nvalue, opp2_nvalue, opp3_nvalue, opp4_nvalue; -u32 opp5_nvalue; -u32 senp_mod, senn_mod; -void __iomem *srbase_addr;
I think you should leave the srbase_addr here and keep the register access the way it is (using __raw_[read|write]*) My preference for general drivers is to keep the omap_hwmod/omap_device usage in the driver to a minimum. More on this below in comments on the _probe function.
I would just rename it from 'srbase_addr' to 'base'.
Quoted 295 lines
arch/arm/mach-omap2/smartreflex.c +40
-172+int srid; +int is_sr_reset; +int is_autocomp_active; +struct clk *vdd_opp_clk; +u32 clk_length; +unsigned int irq; +struct platform_device *pdev;struct list_head node; };/* sr_list contains all the instances of smartreflex module */ static LIST_HEAD (sr_list); -#define SR_REGADDR (offs) (sr->srbase_addr + offset) -static inline void sr_write_reg (struct omap_sr *sr,unsigned offset,u32 value) { -__raw_writel (value,SR_REGADDR (offset)); +struct omap_device *odev =to_omap_device (sr->pdev); + +omap_hwmod_writel (value, odev->hwmods[0 ], offset); }static inline void sr_modify_reg (struct omap_sr *sr,unsigned offset,u32 mask,u32 value) { +struct omap_device *odev =to_omap_device (sr->pdev);u32 reg_val; - reg_val =__raw_readl (SR_REGADDR (offset)); + reg_val =omap_hwmod_readl (odev->hwmods[0 ], offset); reg_val &= ~mask; reg_val |= value; -__raw_writel (reg_val,SR_REGADDR (offset)); +omap_hwmod_writel (reg_val, odev->hwmods[0 ], offset); }static inline u32 sr_read_reg (struct omap_sr *sr,unsigned offset) { -return __raw_readl (SR_REGADDR (offset)); +struct omap_device *odev =to_omap_device (sr->pdev); + +return omap_hwmod_readl (odev->hwmods[0 ], offset); }static struct omap_sr *_sr_lookup (int srid)@@ -98,71 +100,22 @@ static struct omap_sr *_sr_lookup(int srid)static int sr_clk_enable (struct omap_sr *sr) { -if (clk_enable (sr->clk) !=0 ) { -pr_err ("Could not enable %s\n" , sr->clk->name); -return -1 ; - } +struct omap_smartreflex_data *pdata = sr->pdev->dev.platform_data; -/* set fclk- active , iclk- idle */ -sr_modify_reg (sr,ERRCONFIG ,SR_CLKACTIVITY_MASK , -SR_CLKACTIVITY_IOFF_FON ); +if (pdata->device_enable) + pdata->device_enable (sr->pdev);return 0 ; }static void sr_clk_disable (struct omap_sr *sr) { -/* set fclk, iclk- idle */ -sr_modify_reg (sr,ERRCONFIG ,SR_CLKACTIVITY_MASK , -SR_CLKACTIVITY_IOFF_FOFF ); - -clk_disable (sr->clk); - sr->is_sr_reset =1 ; -} - -static struct omap_sr sr1 = { - .srid =SR1 , - .is_sr_reset =1 , - .is_autocomp_active =0 , - .clk_length =0 , - .srbase_addr =OMAP2_L4_IO_ADDRESS (OMAP34XX_SR1_BASE ), -}; - -static struct omap_sr sr2 = { - .srid =SR2 , - .is_sr_reset =1 , - .is_autocomp_active =0 , - .clk_length =0 , - .srbase_addr =OMAP2_L4_IO_ADDRESS (OMAP34XX_SR2_BASE ), -}; - -static void cal_reciprocal (u32 sensor,u32 *sengain,u32 *rnsen) -{ -u32 gn, rn, mul; - -for (gn =0 ; gn <GAIN_MAXLIMIT ; gn++) { - mul =1 << (gn +8 ); - rn = mul / sensor; -if (rn <R_MAXLIMIT ) { - *sengain = gn; - *rnsen = rn; - } - } -} - -static u32 cal_test_nvalue (u32 sennval,u32 senpval) -{ -u32 senpgain, senngain; -u32 rnsenp, rnsenn; +struct omap_smartreflex_data *pdata = sr->pdev->dev.platform_data; -/* Calculating the gain and reciprocal of the SenN and SenP values */ -cal_reciprocal (senpval, &senpgain, &rnsenp); -cal_reciprocal (sennval, &senngain, &rnsenn); +if (pdata->device_idle) + pdata->device_idle (sr->pdev); -return (senpgain <<NVALUERECIPROCAL_SENPGAIN_SHIFT ) | - (senngain <<NVALUERECIPROCAL_SENNGAIN_SHIFT ) | - (rnsenp <<NVALUERECIPROCAL_RNSENP_SHIFT ) | - (rnsenn <<NVALUERECIPROCAL_RNSENN_SHIFT ); + sr->is_sr_reset =1 ; }static u8 get_vdd1_opp (void )@@ -255,76 +208,6 @@ static void sr_set_clk_length(struct omap_sr *sr) } } -static void sr_set_efuse_nvalues (struct omap_sr *sr) -{ -if (sr->srid ==SR1 ) { - sr->senn_mod = (omap_ctrl_readl (OMAP343X_CONTROL_FUSE_SR ) & -OMAP343X_SR1_SENNENABLE_MASK ) >> -OMAP343X_SR1_SENNENABLE_SHIFT ; - sr->senp_mod = (omap_ctrl_readl (OMAP343X_CONTROL_FUSE_SR ) & -OMAP343X_SR1_SENPENABLE_MASK ) >> -OMAP343X_SR1_SENPENABLE_SHIFT ; - - sr->opp5_nvalue =omap_ctrl_readl ( -OMAP343X_CONTROL_FUSE_OPP5_VDD1 ); - sr->opp4_nvalue =omap_ctrl_readl ( -OMAP343X_CONTROL_FUSE_OPP4_VDD1 ); - sr->opp3_nvalue =omap_ctrl_readl ( -OMAP343X_CONTROL_FUSE_OPP3_VDD1 ); - sr->opp2_nvalue =omap_ctrl_readl ( -OMAP343X_CONTROL_FUSE_OPP2_VDD1 ); - sr->opp1_nvalue =omap_ctrl_readl ( -OMAP343X_CONTROL_FUSE_OPP1_VDD1 ); - }else if (sr->srid ==SR2 ) { - sr->senn_mod = (omap_ctrl_readl (OMAP343X_CONTROL_FUSE_SR ) & -OMAP343X_SR2_SENNENABLE_MASK ) >> -OMAP343X_SR2_SENNENABLE_SHIFT ; - - sr->senp_mod = (omap_ctrl_readl (OMAP343X_CONTROL_FUSE_SR ) & -OMAP343X_SR2_SENPENABLE_MASK ) >> -OMAP343X_SR2_SENPENABLE_SHIFT ; - - sr->opp3_nvalue =omap_ctrl_readl ( -OMAP343X_CONTROL_FUSE_OPP3_VDD2 ); - sr->opp2_nvalue =omap_ctrl_readl ( -OMAP343X_CONTROL_FUSE_OPP2_VDD2 ); - sr->opp1_nvalue =omap_ctrl_readl ( -OMAP343X_CONTROL_FUSE_OPP1_VDD2 ); - } -} - -/* Hard coded nvalues for testing purposes, may cause device to hang! */ -static void sr_set_testing_nvalues (struct omap_sr *sr) -{ -if (sr->srid ==SR1 ) { - sr->senp_mod =0x03 ;/* SenN-M5 enabled */ - sr->senn_mod =0x03 ; - -/* calculate nvalues for each opp */ - sr->opp5_nvalue =cal_test_nvalue (0xacd +0x330 ,0x848 +0x330 ); - sr->opp4_nvalue =cal_test_nvalue (0x964 +0x2a0 ,0x727 +0x2a0 ); - sr->opp3_nvalue =cal_test_nvalue (0x85b +0x200 ,0x655 +0x200 ); - sr->opp2_nvalue =cal_test_nvalue (0x506 +0x1a0 ,0x3be +0x1a0 ); - sr->opp1_nvalue =cal_test_nvalue (0x373 +0x100 ,0x28c +0x100 ); - }else if (sr->srid ==SR2 ) { - sr->senp_mod =0x03 ; - sr->senn_mod =0x03 ; - - sr->opp3_nvalue =cal_test_nvalue (0x76f +0x200 ,0x579 +0x200 ); - sr->opp2_nvalue =cal_test_nvalue (0x4f5 +0x1c0 ,0x390 +0x1c0 ); - sr->opp1_nvalue =cal_test_nvalue (0x359 ,0x25d ); - } - -} - -static void sr_set_nvalues (struct omap_sr *sr) -{ -if (SR_TESTING_NVALUES ) -sr_set_testing_nvalues (sr); -else -sr_set_efuse_nvalues (sr); -} -static void sr_configure_vp (int srid) {u32 vpconfig;@@ -438,12 +321,13 @@ static void sr_configure(struct omap_sr *sr) {u32 sr_config;u32 senp_en , senn_en; +struct omap_smartreflex_data *pdata = sr->pdev->dev.platform_data;if (sr->clk_length ==0 )sr_set_clk_length (sr); - senp_en = sr->senp_mod; - senn_en = sr->senn_mod; + senp_en = pdata->senp_mod; + senn_en = pdata->senn_mod;if (sr->srid ==SR1 ) { sr_config =SR1_SRCONFIG_ACCUMDATA | (sr->clk_length << SRCONFIG_SRCLKLENGTH_SHIFT) |@@ -571,57 +455,28 @@ static int sr_enable(struct omap_sr *sr, u32 target_opp_no) {u32 nvalue_reciprocal, v;struct omap_opp *opp; +struct omap_smartreflex_data *pdata = sr->pdev->dev.platform_data;int uvdc;char vsel; - sr->req_opp_no = target_opp_no; -if (sr->srid ==SR1 ) { -switch (target_opp_no) { -case 5 : - nvalue_reciprocal = sr->opp5_nvalue; -break ; -case 4 : - nvalue_reciprocal = sr->opp4_nvalue; -break ; -case 3 : - nvalue_reciprocal = sr->opp3_nvalue; -break ; -case 2 : - nvalue_reciprocal = sr->opp2_nvalue; -break ; -case 1 : - nvalue_reciprocal = sr->opp1_nvalue; -break ; -default : - nvalue_reciprocal = sr->opp3_nvalue; -break ; - } - opp =opp_find_by_opp_id (OPP_MPU , target_opp_no);if (!opp)return false; }else { -switch (target_opp_no) { -case 3 : - nvalue_reciprocal = sr->opp3_nvalue; -break ; -case 2 : - nvalue_reciprocal = sr->opp2_nvalue; -break ; -case 1 : - nvalue_reciprocal = sr->opp1_nvalue; -break ; -default : - nvalue_reciprocal = sr->opp3_nvalue; -break ; - } - opp =opp_find_by_opp_id (OPP_L3 , target_opp_no);if (!opp)return false; } +if (!pdata->sr_nvalue) { +pr_notice ("N target values does not exist for SR%d\n" , + sr->srid); +return false; + } + + nvalue_reciprocal = pdata->sr_nvalue[target_opp_no -1 ]; +if (nvalue_reciprocal ==0 ) {pr_notice ("OPP%d doesn't support SmartReflex\n" , target_opp_no);@@ -1033,49 +888,93 @@ static struct kobj_attribute sr_vdd2_autocomp = { .store = omap_sr_vdd2_autocomp_store, }; +static int __devinit omap_smartreflex_probe (struct platform_device *pdev) +{ +struct omap_sr *sr_info =kzalloc (sizeof (struct omap_sr ),GFP_KERNEL ); +struct omap_device *odev =to_omap_device (pdev); +int ret =0 ;
arch/arm/mach-omap2/smartreflex.c static struct kobj_attribute sr_vdd2_autocomp = { · line 905
Quoted 10 lines
arch/arm/mach-omap2/smartreflex.c +10
-0+ +if (WARN_ON (!sr_info)) +return -ENOMEM ; + sr_info->pdev = pdev; + sr_info->srid = pdev->id +1 ; + sr_info->is_sr_reset =1 , + sr_info->is_autocomp_active =0 ; + sr_info->clk_length =0 ; +if (odev->hwmods[0 ]->mpu_irqs) + sr_info->irq = odev->hwmods[0 ]->mpu_irqs[0 ].irq;
You should use platform_get_resource(..., IORESOURCE_IRQ) here instead of accessing the hwmod. (or better, platform_get_irq().)
Remember that omap_device_build() builds a platform_device as well with all the resources (base addresses, IRQs, DMA channels) so the standard platform_get_resource() calls should be used to get all those.
And, for the base address, use
sr_info->base = platform_get_resource(pdev, IORESOURCE_MEM);
Ideally, as generic driver here should have no (or minimal) knowledge of omap_device/omap_hwmod internals.
Quoted 28 lines
arch/arm/mach-omap2/smartreflex.c +27
-0+sr_set_clk_length (sr_info); + +if (sr_info->srid ==SR1 ) { + sr_info->vdd_opp_clk =clk_get (NULL ,"dpll1_ck" ); + ret =sysfs_create_file (power_kobj, &sr_vdd1_autocomp.attr); +if (ret) +pr_err ("sysfs_create_file failed: %d\n" , ret); + }else { + sr_info->vdd_opp_clk =clk_get (NULL ,"l3_ick" ); + ret =sysfs_create_file (power_kobj, &sr_vdd2_autocomp.attr); +if (ret) +pr_err ("sysfs_create_file failed: %d\n" , ret); + } + +/* Call the VPConfig */ +sr_configure_vp (sr_info->srid); +list_add (&sr_info->node, &sr_list); +pr_info ("SmartReflex driver initialized\n" ); + +return ret; +} + +static int __devexit omap_smartreflex_remove(struct platform_device *pdev) +{ +struct omap_sr *sr_info =_sr_lookup (pdev->id +1 ); +/* Disable Autocompensation if enabled before removing the module */ +if (sr_info->is_autocomp_active ==1 )
arch/arm/mach-omap2/smartreflex.c static struct kobj_attribute sr_vdd2_autocomp = { · line 942
Quoted 10 lines
arch/arm/mach-omap2/smartreflex.c +8
-1+sr_stop_vddautocomap (sr_info->srid); +list_del (&sr_info->node); +kfree (sr_info); -static int __init omap3_sr_init (void ) +return 0 ; +} + +static struct platform_driver smartreflex_driver = { + .probe = omap_smartreflex_probe,
minor nit... since you're using platform_device_probe(), you don't need a .probe function here, and you can make omap_smartreflex_probe() __init.
Quoted 85 lines
arch/arm/mach-omap2/smartreflex.c +22
-27+ .remove = omap_smartreflex_remove, + .driver = { + .name = "smartreflex", + }, +}; + +static int __init sr_init (void ) {int ret =0 ;u8 RdReg; +/* TODO: Find an appropriate place for this */ /* Enable SR on T2 */ ret =twl_i2c_read_u8 (TWL4030_MODULE_PM_RECEIVER , &RdReg,R_DCDC_GLOBAL_CFG ); - RdReg |=DCDC_GLOBAL_CFG_ENABLE_SRFLX ; ret |=twl_i2c_write_u8 (TWL4030_MODULE_PM_RECEIVER , RdReg,R_DCDC_GLOBAL_CFG ); -if (cpu_is_omap34xx ()) { - sr1.clk =clk_get (NULL ,"sr1_fck" ); - sr2.clk =clk_get (NULL ,"sr2_fck" ); - } - sr1.vdd_opp_clk =clk_get (NULL ,"dpll1_ck" ); - sr2.vdd_opp_clk =clk_get (NULL ,"l3_ick" ); -sr_set_clk_length (&sr1); -sr_set_clk_length (&sr2); - -/* Call the VPConfig, VCConfig, set N Values. */ -sr_set_nvalues (&sr1); -sr_configure_vp (SR1 ); - -sr_set_nvalues (&sr2); -sr_configure_vp (SR2 ); - -pr_info ("SmartReflex driver initialized\n" ); - ret =sysfs_create_file (power_kobj, &sr_vdd1_autocomp.attr); -if (ret) -pr_err ("sysfs_create_file failed: %d\n" , ret); + ret =platform_driver_probe (&smartreflex_driver, + omap_smartreflex_probe); - ret =sysfs_create_file (power_kobj, &sr_vdd2_autocomp.attr);if (ret) -pr_err ("sysfs_create_file failed: %d\n" , ret); -list_add (&sr1.node, &sr_list); -list_add (&sr2.node, &sr_list); - +pr_err ("platform driver register failed for smartreflex" );return 0 ; } -late_initcall (omap3_sr_init); +void __exit sr_exit(void) +{ +platform_driver_unregister (&smartreflex_driver); +} +late_initcall (sr_init); +module_exit (sr_exit); + +MODULE_DESCRIPTION ("OMAP SMARTREFLEX DRIVER" ); +MODULE_LICENSE ("GPL" ); +MODULE_ALIAS ("platform:" DRIVER_NAME ); +MODULE_AUTHOR ("Texas Instruments Inc" );arch/arm/mach-omap2/smartreflex.h +5
-0@@ -14,6 +14,8 @@* published by the Free Software Foundation. */ +#include <linux/platform_device.h> +#define PHY_TO_OFF_PM_MASTER (p) (p - 0x36)#define PHY_TO_OFF_PM_RECIEVER (p) (p - 0x5b)#define PHY_TO_OFF_PM_INT (p) (p - 0x2e)@@ -276,6 +278,30 @@ struct omap_smartreflex_dev_data {* do anything. */ #ifdef CONFIG_OMAP_SMARTREFLEX +/** +* omap_smartreflex_data - Smartreflex platform data +*
arch/arm/mach-omap2/smartreflex.h struct omap_smartreflex_dev_data { · line 293
Quoted 10 lines
arch/arm/mach-omap2/smartreflex.h +10
-0+* @senp_mod : SENPENABLE value for the sr +* @senn_mod : SENNENABLE value for sr +* @sr_nvalue : array of n target values for sr +* @enable_on_init : whether this sr module needs to enabled at +* boot up or not +* @device_enable : fn pointer to be populated with omap_device +* enable API +* @device_shutdown : fn pointer to be populated with omap_device +* shutdown API +* @device_idle : fn pointer to be pouplated with omap_device idle API
You can drop the comments about omap_device API. These are intended to be generic pointers. The device part is free to fill those out
arch/arm/mach-omap2/smartreflex.h struct omap_smartreflex_dev_data { · line 295
Quoted 2 lines
arch/arm/mach-omap2/smartreflex.h +2
-0+*/ +struct omap_smartreflex_data {
Also, how about a rename to omap_sr_data;
Quoted 18 lines
arch/arm/mach-omap2/smartreflex.h +9
-0+u32 senp_mod; +u32 senn_mod; +u32 *sr_nvalue; +bool enable_on_init; +int (*device_enable)(struct platform_device *pdev); +int (*device_shutdown)(struct platform_device *pdev); +int (*device_idle)(struct platform_device *pdev); +}; +void enable_smartreflex (int srid);void disable_smartreflex (int srid);int sr_voltagescale_vcbypass (u32 t_opp,u32 c_opp,u8 t_vsel,u8 c_vsel);arch/arm/mach-omap2/sr_device.c new file +0
-0
arch/arm/mach-omap2/sr_device.c line 2
Quoted 2 lines
arch/arm/mach-omap2/sr_device.c new file +2
-0@@ -0,0 +1,139 @@ +/* +* linux/arch/arm/mach-omap2/sr_device.c
Please drop the filename from the header.
Quoted 79 lines
arch/arm/mach-omap2/sr_device.c new file +79
-0+* OMAP3/OMAP4 smartreflex device file +* +* Author: Thara Gopinath <[email protected]> +* +* Based originally on code from smartreflex.c +* Copyright (C) 2010 Texas Instruments, Inc. +* Thara Gopinath <[email protected]> +* +* Copyright (C) 2008 Nokia Corporation +* Kalle Jokiniemi +* +* Copyright (C) 2007 Texas Instruments, Inc. +* Lesly A M <[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +*/ + +#include <linux/err.h> + +#include <plat/control.h> +#include <plat/omap_hwmod.h> +#include <plat/omap_device.h> +#include <plat/opp.h> + +#include "smartreflex.h" + +#define MAX_HWMOD_NAME_LEN 16 + +struct omap_device_pm_latency omap_sr_latency[] = { + { + .deactivate_func = omap_device_idle_hwmods, + .activate_func = omap_device_enable_hwmods, + .flags =OMAP_DEVICE_LATENCY_AUTO_ADJUST + }, +}; + +/* Read EFUSE values from control registers for OMAP3430 */ +static void __init sr_read_efuse ( +struct omap_smartreflex_dev_data *dev_data, +struct omap_smartreflex_data *sr_data) +{ +int i; + +if (WARN_ON (!dev_data || !dev_data->volts_supported || + !dev_data->efuse_sr_control || + !dev_data->efuse_nvalues_offs)) +return ; + + sr_data->sr_nvalue =kzalloc (sizeof (sr_data->sr_nvalue) * + dev_data->volts_supported ,GFP_KERNEL ); + sr_data->senn_mod = (omap_ctrl_readl (dev_data->efuse_sr_control) & + (0x3 << dev_data->sennenable_shift) >> + dev_data->sennenable_shift); + sr_data->senp_mod = (omap_ctrl_readl (dev_data->efuse_sr_control) & + (0x3 << dev_data->senpenable_shift) >> + dev_data->senpenable_shift); +for (i =0 ; i < dev_data->volts_supported; i++) + sr_data->sr_nvalue[i] =omap_ctrl_readl ( + dev_data->efuse_nvalues_offs[i]); +} + +/* +* Hard coded nvalues for testing purposes for OMAP3430, +* may cause device to hang! +*/ +static void __init sr_set_testing_nvalues ( +struct omap_smartreflex_dev_data *dev_data, +struct omap_smartreflex_data *sr_data) +{ +int i; + +if (WARN_ON (!dev_data || !dev_data->volts_supported || + !dev_data->test_nvalues)) +return ; + + sr_data->sr_nvalue =kzalloc (sizeof (sr_data->sr_nvalue) * + dev_data->volts_supported ,GFP_KERNEL );
arch/arm/mach-omap2/sr_device.c line 92
Quoted 10 lines
arch/arm/mach-omap2/sr_device.c new file +10
-0+ sr_data->senn_mod = dev_data->test_sennenable; + sr_data->senp_mod = dev_data->test_senpenable; +for (i =0 ; i < dev_data->volts_supported; i++) + sr_data->sr_nvalue[i] = dev_data->test_nvalues[i]; +} + +static void __init sr_set_nvalues (struct omap_smartreflex_dev_data *dev_data, +struct omap_smartreflex_data *sr_data) +{ +if (cpu_is_omap34xx ()) {
Why this check? Looks like the called functions already check for valid data. Also, I don't see this changed/updated in the 3630 patches.
Quoted 11 lines
arch/arm/mach-omap2/sr_device.c new file +11
-0+if (SR_TESTING_NVALUES ) +sr_set_testing_nvalues (dev_data, sr_data); +else +sr_read_efuse (dev_data, sr_data); + } +} + +static int __init omap_devinit_smartreflex (void ) +{ +int i =0 ; +char *name ="smartreflex" ;
arch/arm/mach-omap2/sr_device.c line 113
Quoted 10 lines
arch/arm/mach-omap2/sr_device.c new file +10
-0+ + do { + struct omap_smartreflex_data *sr_data; + struct omap_smartreflex_dev_data *sr_dev_data; + struct omap_device *od; + struct omap_hwmod *oh; + char oh_name[MAX_HWMOD_NAME_LEN + 1]; + + snprintf(oh_name, MAX_HWMOD_NAME_LEN, "sr%d_hwmod", i + 1); + oh = omap_hwmod_lookup(oh_name);
Should be using the hwmod_class to iterate: omap_hwmod_for_each_by_class()
Quoted 16 lines
arch/arm/mach-omap2/sr_device.c new file +16
-0+if (!oh) +break ; + + sr_data =kzalloc (sizeof (struct omap_smartreflex_data ), +GFP_KERNEL ); + sr_dev_data = (struct omap_smartreflex_dev_data *)oh->dev_attr; +if (WARN_ON (!sr_data)) +return -ENOMEM ; + + sr_data->enable_on_init = false; + sr_data->device_enable = omap_device_enable; + sr_data->device_shutdown = omap_device_shutdown; + sr_data->device_idle = omap_device_idle; +sr_set_nvalues (sr_dev_data, sr_data); + + od = omap_device_build(name, i, oh, sr_data, sizeof(*sr_data),
arch/arm/mach-omap2/sr_device.c line 139
Quoted 10 lines
arch/arm/mach-omap2/sr_device.c new file +10
-0+ omap_sr_latency, + ARRAY_SIZE(omap_sr_latency), 0); +WARN (IS_ERR (od),"Could not build omap_device for %s: %s.\n" , + name, oh->name); + i++; + }while (1 ); + +return 0 ; +} +arch_initcall (omap_devinit_smartreflex);
Kevin
Re: [PATCHv3 01/22] OMAP3: PM: Adding hwmod data for Smartreflex
In reply to Thara GopinathQuoted 2 lines · Thara Gopinath
This patch adds the hwmod strucutres and other hwmod data for OMAP3 Smartreflex IP's.
Should also comment about the additional data used in dev_attr as well.
Quoted 6 lines
Signed-off-by Thara Gopinath <[email protected]>--- arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 135 ++++++++++++++++++++++++++++ arch/arm/mach-omap2/smartreflex.h | 33 +++++++ 2 files changed, 168 insertions(+), 0 deletions(-)
[...]
Quoted 21 lines
arch/arm/mach-omap2/smartreflex.h +13
-0@@ -237,6 +237,39 @@ extern u32 current_vdd2_opp;#define SR_TESTING_NVALUES 0#endif +/** +* omap_smartreflex_dev_data - Smartreflex device specific data +* +* @volts_supported : Number of distinct voltages possible for the VDD +* associated with this smartreflex module. +* @efuse_sr_control : The regisrter offset of control_fuse_sr efuse +* register from which sennenable and senpenable values +* are obtained. +* @sennenable_shift : The shift in the control_fuse_sr register for +* obtaining the sennenable value for this smartreflex +* module. +* @senpenable_shift : The shift in the control_fuse_sr register for +* obtaining the senpenable value for this smartreflex
arch/arm/mach-omap2/smartreflex.h extern u32 current_vdd2_opp; · line 262
Quoted 10 lines
arch/arm/mach-omap2/smartreflex.h +10
-0+* module. +* @efuse_nvalues_offs : Array of efuse offsets from which ntarget values can +* be retrieved. Number of efuse offsets in this arrray +* is equal to the volts_supported value ie one efuse +* register per supported voltage. +* @test_sennenable : SENNENABLE test value +* @test_senpenable : SENPENABLE test value. +* @test_nvalues : Array of test ntarget values. +*/ +struct omap_smartreflex_dev_data {
Minor nit here, but this could be named omap_sr_dev_data to keep the name shorter and avoid some of the wrapping that has to be done in other code because of this.
Kevin
Quoted 21 lines · Thara Gopinath
The main motivations behind this patch series are the following
1. Making smartreflex a platform driver with omap-device layer.
2. Separating voltage specific code fromsmartreflex.cand other locations and consolidating them intovoltage.candvoltage.h.
3. Smartreflex module can have Class 1 Class 2 or Class 3 implementations depending on the PMIC in use. Makingsmartreflex.ccapable of handling both the Class 2 and 3 implementaions and separating out class specific code into a separate class driver.
4. Remove dependencies on opp id in the smartreflex and voltage drivers
5. Implementating latest TI recommended register settings for Smartreflex and Voltage processor module as well as recommended sequences for enabling and disabling of Smartreflex and Voltage processor modules.
6. Implementing VP force update method of voltage scaling which is again TI hardware recommended.What this patch series does not address are
1. Separating PMIC specific portions from smartreflex and voltage code.
2. OMAP3630 and OMP4 smartreflex support.
Quoted 8 lines
This patch series is based on Kevin's PM tree origin/pm-wip-opp branch and is dependent on the following patches not yet applied onto this branch.
http://patchwork.kernel.org/patch/81504/ http://patchwork.kernel.org/patch/81606/This patch series has been tested on OMAP3430 SDP with basic power management tests including the dvfs scripts.
Will get to reviewing this later this week. In the mean time, I pushed a new pm-wip-sr branch with this version of the series.
Thanks,
Kevin
Quoted 21 lines · Thara Gopinath
The main motivations behind this patch series are the following
1. Making smartreflex a platform driver with omap-device layer.
2. Separating voltage specific code fromsmartreflex.cand other locations and consolidating them intovoltage.candvoltage.h.
3. Smartreflex module can have Class 1 Class 2 or Class 3 implementations depending on the PMIC in use. Makingsmartreflex.ccapable of handling both the Class 2 and 3 implementaions and separating out class specific code into a separate class driver.
4. Remove dependencies on opp id in the smartreflex and voltage drivers
5. Implementating latest TI recommended register settings for Smartreflex and Voltage processor module as well as recommended sequences for enabling and disabling of Smartreflex and Voltage processor modules.
6. Implementing VP force update method of voltage scaling which is again TI hardware recommended.What this patch series does not address are
1. Separating PMIC specific portions from smartreflex and voltage code.
2. OMAP3630 and OMP4 smartreflex support.
Quoted 8 lines
This patch series is based on Kevin's PM tree origin/pm-wip-opp branch and is dependent on the following patches not yet applied onto this branch.
http://patchwork.kernel.org/patch/81504/ http://patchwork.kernel.org/patch/81606/This patch series has been tested on OMAP3430 SDP with basic power management tests including the dvfs scripts.
First some general comments...
- check multi-line comment style
- use of dev_err() instead of pr_err() (or dev_* instead of pr_*) wherever you have a valid platform_device. This will print messages with the specific SR device name so you get more detailed messages. It will also avoid you having to use sr_info->srid since that number is already part of the device name.
And now, IMHO, this is getting close enough, where I think it's getting mostly ready for submission upstream. To that end, I think it's time to start creating this series against mainline, instead of against the PM branch.
This is basically a rewrite, so I think it makes sense to breifly summarize the history in the first patch, but then build from scratch against mainline (except for SRF changes which will have to be a separate series based on the PM branch.)
As it is, the series is getting hard to follow as there are several things that are cleaned up from the old code and then removed later in the series etc. For that reason, I'd now like to see this as a fresh series against mainline.
Actually, currnely it will have to be based on my pm-vc branch which is a small series of VC init/setup patches that I'll be queueing for 2.6.35, but itself is based on mainline.
The SR series could broken up as follows (only a suggestion)
- Creation of voltage layer: current pm-vc branch + voltage.c
- Creation of device/platform init: hwmods, sr_device.c
- Creation of driver: smartreflex*.[ch], sr_device.c
These should each have a brief summary of history and main contributors, but you as primary author.
Kevin
Quoted 70 lines
Quoted 70 lines
-----Original Message-----
From: Kevin Hilman [mailto:[email protected]]
Sent: Wednesday, April 28, 2010 12:48 AM
To: Gopinath, Thara
Cc: [email protected]; [email protected]; Cousson, Benoit; Sripathy, Vishwanath; Sawant, Anand
Subject: Re: [PATCHv3 00/22] OMAP3: PM: Smartreflex and voltage revampQuoted 21 lines · Thara Gopinath
The main motivations behind this patch series are the following
1. Making smartreflex a platform driver with omap-device layer.
2. Separating voltage specific code fromsmartreflex.cand other locations and consolidating them intovoltage.candvoltage.h.
3. Smartreflex module can have Class 1 Class 2 or Class 3 implementations depending on the PMIC in use. Makingsmartreflex.ccapable of handling both the Class 2 and 3 implementaions and separating out class specific code into a separate class driver.
4. Remove dependencies on opp id in the smartreflex and voltage drivers
5. Implementating latest TI recommended register settings for Smartreflex and Voltage processor module as well as recommended sequences for enabling and disabling of Smartreflex and Voltage processor modules.
6. Implementing VP force update method of voltage scaling which is again TI hardware recommended.What this patch series does not address are
1. Separating PMIC specific portions from smartreflex and voltage code.
2. OMAP3630 and OMP4 smartreflex support.Quoted 8 lines
This patch series is based on Kevin's PM tree origin/pm-wip-opp branch and is dependent on the following patches not yet applied onto this branch.
http://patchwork.kernel.org/patch/81504/ http://patchwork.kernel.org/patch/81606/This patch series has been tested on OMAP3430 SDP with basic power management tests including the dvfs scripts.
First some general comments...
- check multi-line comment style
- use of
dev_err()instead ofpr_err()(or dev_* instead of pr_*) wherever you have a validplatform_device. This will print messages with the specific SR device name so you get more detailed messages. It will also avoid you having to usesr_info->sridsince that number is already part of the device name.And now, IMHO, this is getting close enough, where I think it's getting mostly ready for submission upstream. To that end, I think it's time to start creating this series against mainline, instead of against the PM branch.
This is basically a rewrite, so I think it makes sense to breifly summarize the history in the first patch, but then build from scratch against mainline (except for SRF changes which will have to be a separate series based on the PM branch.)
As it is, the series is getting hard to follow as there are several things that are cleaned up from the old code and then removed later in the series etc. For that reason, I'd now like to see this as a fresh series against mainline.
Actually, currnely it will have to be based on my pm-vc branch which is a small series of VC init/setup patches that I'll be queueing for 2.6.35, but itself is based on mainline.
Quoted 7 lines
Quoted 7 lines
The SR series could broken up as follows (only a suggestion)
- Creation of voltage layer: current pm-vc branch +
voltage.c- Creation of device/platform init: hwmods,
sr_device.c- Creation of driver: smartreflex*.[ch],
sr_device.c
Kevin,
I could create this series against mainline but I need OPP layer for voltage layer..
Regards,
Thara
Quoted 4 lines
Quoted 4 lines
These should each have a brief summary of history and main contributors, but you as primary author.
Kevin
Quoted 72 lines · Thara
Quoted 72 lines
Quoted 72 lines
-----Original Message-----
From: Kevin Hilman [mailto:[email protected]]
Sent: Wednesday, April 28, 2010 12:48 AM
To: Gopinath, Thara
Cc: [email protected]; [email protected]; Cousson, Benoit; Sripathy, Vishwanath; Sawant, Anand
Subject: Re: [PATCHv3 00/22] OMAP3: PM: Smartreflex and voltage revampQuoted 21 lines · Thara Gopinath
The main motivations behind this patch series are the following
1. Making smartreflex a platform driver with omap-device layer.
2. Separating voltage specific code fromsmartreflex.cand other locations and consolidating them intovoltage.candvoltage.h.
3. Smartreflex module can have Class 1 Class 2 or Class 3 implementations depending on the PMIC in use. Makingsmartreflex.ccapable of handling both the Class 2 and 3 implementaions and separating out class specific code into a separate class driver.
4. Remove dependencies on opp id in the smartreflex and voltage drivers
5. Implementating latest TI recommended register settings for Smartreflex and Voltage processor module as well as recommended sequences for enabling and disabling of Smartreflex and Voltage processor modules.
6. Implementing VP force update method of voltage scaling which is again TI hardware recommended.What this patch series does not address are
1. Separating PMIC specific portions from smartreflex and voltage code.
2. OMAP3630 and OMP4 smartreflex support.Quoted 8 lines
This patch series is based on Kevin's PM tree origin/pm-wip-opp branch and is dependent on the following patches not yet applied onto this branch.
http://patchwork.kernel.org/patch/81504/ http://patchwork.kernel.org/patch/81606/This patch series has been tested on OMAP3430 SDP with basic power management tests including the dvfs scripts.
First some general comments...
- check multi-line comment style
- use of
dev_err()instead ofpr_err()(or dev_* instead of pr_*) wherever you have a validplatform_device. This will print messages with the specific SR device name so you get more detailed messages. It will also avoid you having to usesr_info->sridsince that number is already part of the device name.And now, IMHO, this is getting close enough, where I think it's getting mostly ready for submission upstream. To that end, I think it's time to start creating this series against mainline, instead of against the PM branch.
This is basically a rewrite, so I think it makes sense to breifly summarize the history in the first patch, but then build from scratch against mainline (except for SRF changes which will have to be a separate series based on the PM branch.)
As it is, the series is getting hard to follow as there are several things that are cleaned up from the old code and then removed later in the series etc. For that reason, I'd now like to see this as a fresh series against mainline.
Actually, currnely it will have to be based on my pm-vc branch which is a small series of VC init/setup patches that I'll be queueing for 2.6.35, but itself is based on mainline.
The SR series could broken up as follows (only a suggestion)
- Creation of voltage layer: current pm-vc branch +
voltage.c
Quoted 8 lines
Quoted 3 lines
Quoted 3 lines
- Creation of device/platform init: hwmods,
sr_device.c- Creation of driver: smartreflex*.[ch],
sr_device.cKevin,
I could create this series against mainline but I need OPP layer for voltage layer..
Ah, yes. Sorry. Please create against pm-opp, which is based on mainline. I am working on reorganizing pm-opp for upstream.
Kevin