Skip to contentSkip to conversation

X25: Use identifiers for X25 to device interface

PATCH In review Andrew Hendry 2 participants 4 messages Apr 18, 2010

Subsystems (4)
Networking Network drivers Documentation X.25 stack
lore
Share & tools
lore

Andrew Hendry

author
#0 lore raw

PATCH 1/6 X25: Use identifiers for X25 to device interface

Use identifiers in x25_device.h instead of magic numbers for X25 layer 3 to device interface. Also fixed checkpatch notes on updated code.

Signed-off-by Andrew Hendry <[email protected]>
---
 Documentation/networking/x25-iface.txt |   16 +++++++-------
 include/net/x25device.h                |    8 +++++++
 net/x25/x25_dev.c                      |   36 +++++++++++++++++--------------
 3 files changed, 36 insertions(+), 24 deletions(-)
Documentation/networking/x25-iface.txt +8 -8
index 975cc87..78f662e 100644
@@ -20,23 +20,23 @@ the rest of the skbuff, if any more information does exist.
 Packet Layer to Device Driver
 -----------------------------
 
-First Byte = 0x00
+First Byte = 0x00 (X25_IFACE_DATA)
 
 This indicates that the rest of the skbuff contains data to be transmitted
 over the LAPB link. The LAPB link should already exist before any data is
 passed down.
 
-First Byte = 0x01
+First Byte = 0x01 (X25_IFACE_CONNECT)
 
 Establish the LAPB link. If the link is already established then the connect
 confirmation message should be returned as soon as possible.
 
-First Byte = 0x02
+First Byte = 0x02 (X25_IFACE_DISCONNECT)
 
 Terminate the LAPB link. If it is already disconnected then the disconnect
 confirmation message should be returned as soon as possible.
 
-First Byte = 0x03
+First Byte = 0x03 (X25_IFACE_PARAMS)
 
 LAPB parameters. To be defined.
 

@@ -44,22 +44,22 @@ LAPB parameters. To be defined.
 Device Driver to Packet Layer
 -----------------------------
 
-First Byte = 0x00
+First Byte = 0x00 (X25_IFACE_DATA)
 
 This indicates that the rest of the skbuff contains data that has been
 received over the LAPB link.
 
-First Byte = 0x01
+First Byte = 0x01 (X25_IFACE_CONNECT)
 
 LAPB link has been established. The same message is used for both a LAPB
 link connect_confirmation and a connect_indication.
 
-First Byte = 0x02
+First Byte = 0x02 (X25_IFACE_DISCONNECT)
 
 LAPB link has been terminated. This same message is used for both a LAPB
 link disconnect_confirmation and a disconnect_indication.
 
-First Byte = 0x03
+First Byte = 0x03 (X25_IFACE_PARAMS)
 
 LAPB parameters. To be defined.
include/net/x25device.h +8 -0
index 1415bcf..51f8902 100644
@@ -13,4 +13,12 @@ static inline __be16 x25_type_trans(struct sk_buff *skb, struct net_device *dev)
 	
 	return htons(ETH_P_X25);
 }
+
+enum {
+	X25_IFACE_DATA,
+	X25_IFACE_CONNECT,
+	X25_IFACE_DISCONNECT,
+	X25_IFACE_PARAMS
+};
+
 #endif
net/x25/x25_dev.c +20 -16
index b9ef682..9005f6d 100644
@@ -24,6 +24,7 @@
 #include <net/sock.h>
 #include <linux/if_arp.h>
 #include <net/x25.h>
+#include <net/x25device.h>
 
 static int x25_receive_data(struct sk_buff *skb, struct x25_neigh *nb)
 {

@@ -115,19 +116,22 @@ int x25_lapb_receive_frame(struct sk_buff *skb, struct net_device *dev,
 	}
 
 	switch (skb->data[0]) {
-		case 0x00:
-			skb_pull(skb, 1);
-			if (x25_receive_data(skb, nb)) {
-				x25_neigh_put(nb);
-				goto out;
-			}
-			break;
-		case 0x01:
-			x25_link_established(nb);
-			break;
-		case 0x02:
-			x25_link_terminated(nb);
-			break;
+
+	case X25_IFACE_DATA:
+		skb_pull(skb, 1);
+		if (x25_receive_data(skb, nb)) {
+			x25_neigh_put(nb);
+			goto out;
+		}
+		break;
+
+	case X25_IFACE_CONNECT:
+		x25_link_established(nb);
+		break;
+
+	case X25_IFACE_DISCONNECT:
+		x25_link_terminated(nb);
+		break;
 	}
 	x25_neigh_put(nb);
 drop:

@@ -148,7 +152,7 @@ void x25_establish_link(struct x25_neigh *nb)
 				return;
 			}
 			ptr  = skb_put(skb, 1);
-			*ptr = 0x01;
+			*ptr = X25_IFACE_CONNECT;
 			break;
 
 #if defined(CONFIG_LLC) || defined(CONFIG_LLC_MODULE)

@@ -184,7 +188,7 @@ void x25_terminate_link(struct x25_neigh *nb)
 	}
 
 	ptr  = skb_put(skb, 1);
-	*ptr = 0x02;
+	*ptr = X25_IFACE_DISCONNECT;
 
 	skb->protocol = htons(ETH_P_X25);
 	skb->dev      = nb->dev;

@@ -200,7 +204,7 @@ void x25_send_frame(struct sk_buff *skb, struct x25_neigh *nb)
 	switch (nb->dev->type) {
 		case ARPHRD_X25:
 			dptr  = skb_push(skb, 1);
-			*dptr = 0x00;
+			*dptr = X25_IFACE_DATA;
 			break;
 
 #if defined(CONFIG_LLC) || defined(CONFIG_LLC_MODULE)
Signature · 1 line
1.5.6.5
#1 lore raw
Quoted 5 lines · Andrew Hendry

Use identifiers in x25_device.h instead of magic numbers for X25 layer 3 to device interface. Also fixed checkpatch notes on updated code.
[...]

include/net/x25device.h static inline __be16 x25_type_trans(struct sk_buff *skb, struct net_device *dev) · line 22

Quoted 10 lines
include/net/x25device.h +8 -1
-First Byte = 0x00
+First Byte = 0x00 (X25_IFACE_DATA)
[...]
+
+enum {
+	X25_IFACE_DATA,
+	X25_IFACE_CONNECT,
+	X25_IFACE_DISCONNECT,
+	X25_IFACE_PARAMS
+};

Shouldn't you use explicit values here?

enum {
	X25_IFACE_DATA = 0x00, /* explicit value for ABI stability */
	...
#2 lore raw
Quoted 5 lines · John Hughes

Shouldn't you use explicit values here?

enum {
    X25_IFACE_DATA = 0x00, /* explicit value for ABI stability */
    ...

Oh, and is net/x25device.h suitable for inclusion from user space (xotd for example)?

author
#3 lore raw

Hi John,

Thanks, missed that, ill see if any of the driver areas have comments and make a V2 patch with explicit values.

Your right, it would be nice if xotd/xoe could pickup the same definition from user space.
include/net/x25device.h is not intended as a user space header. include/linux/net/x25.h is the user space header for the x25 socket layer interface, so I don't think these definitions should go there.

I think the right way to do it is add a new userspace header include/linux/if_x25.h then include that from net/x25_device.h?

Regards,
Andrew.

Quoted 12 lines · John Hughes
Quoted 6 lines · John Hughes

Shouldn't you use explicit values here?

enum {
   X25_IFACE_DATA = 0x00, /* explicit value for ABI stability */
   ...

Oh, and is net/x25device.h suitable for inclusion from user space (xotd for example)?