Simple fan question
Hi folks !
I'm writing some support for d-link dns323 rev C1 NAS. It has a fan that is controlled by some non-programmable PWM circuit. Basically, all I can do is tweak to GPIOs that controls the feed into the circuitry for the fans to be off, slow or fast.
I don't know what the actual PWM values are for "slow" or "fast". I -might- be able to do some measurements but I can't promise it.
Now I'm trying to do a simple hwmon driver for that in order to easy userspace support for these guys, and I don't really see a 'nice' way to expose that which would fit the interfaces documented Documentation/hwmon/sysfs-interface.
So before I do something horrible, I felt I might poke you guys see if you have a good idea here :-)
Before I read the above document I was thinking about a sysfs file that contains "off", "slow" or "fast" but it looks like this won't fit at all the typical hwmon APIs.
Another comment while at it is when implementing the thermal control for PowerMacs a while back (windfarm etc...) I had to deal with two different type of interfaces to fans. RPM controlled and PWM controlled.
The later basically let me program a percentile value (a percent of the duty cycle).
I looks like the described sysfs interface only does RPM, or at least doesn't provide a way to expose the units used...
Cheers,
Ben.
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Hi!
Quoted 11 lines · Benjamin Herrenschmidt
Hi folks !
I'm writing some support for d-link dns323 rev C1 NAS. It has a fan that is controlled by some non-programmable PWM circuit. Basically, all I can do is tweak to GPIOs that controls the feed into the circuitry for the fans to be off, slow or fast.
I don't know what the actual PWM values are for "slow" or "fast". I -might- be able to do some measurements but I can't promise it.
Are you doing it for debian installation on DNS-323? I know, it existed, but surprised it did not have fan control...
Have you looked at fan control for standard firmware included in funplug? I think dns323-fan source is available and can set exact fan RPM...
--
DG
NJ
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Hi Ben,
Quoted 13 lines · Benjamin Herrenschmidt
I'm writing some support for d-link dns323 rev C1 NAS. It has a fan that is controlled by some non-programmable PWM circuit. Basically, all I can do is tweak to GPIOs that controls the feed into the circuitry for the fans to be off, slow or fast.
I don't know what the actual PWM values are for "slow" or "fast". I -might- be able to do some measurements but I can't promise it.
Now I'm trying to do a simple hwmon driver for that in order to easy userspace support for these guys, and I don't really see a 'nice' way to expose that which would fit the interfaces documented
Documentation/hwmon/sysfs-interface.
Quoted 6 lines
So before I do something horrible, I felt I might poke you guys see if you have a good idea here :-)
Before I read the above document I was thinking about a sysfs file that contains "off", "slow" or "fast" but it looks like this won't fit at all the typical hwmon APIs.
Indeed, that wouldn't fit. The nearest entry in the document is:
pwm[1-*] Pulse width modulation fan control.
Integer value in the range 0 to 255 RW 255 is max or 100%.
In your case, the file would have only 3 possible values, with "off" mapping to 0, and "slow" and "fast" mapping to arbitrary positive values, like 64 and 192 or whatever you think is suitable. I understand that in your case, you don't really control the PWM output directly, but we do not have any interface for this, and I don't think there would be much value in adding one.
That being said, I am also only mildly convinced that fitting your chip in the standard pwm1 interface will be very helpful. I don't really expect tools such as the fancontrol script to behave properly when the pwm1 file only support a small number of discrete values. So the benefit of using the standard file name and semantics seems thin.
Quoted 6 lines
Another comment while at it is when implementing the thermal control for PowerMacs a while back (windfarm etc...) I had to deal with two different type of interfaces to fans. RPM controlled and PWM controlled.
The later basically let me program a percentile value (a percent of the duty cycle).
This is exactly what pwm[1-*] files are about, except that we used range 0-255 instead of 0-100 for historical and practical reasons.
Quoted 2 lines
I looks like the described sysfs interface only does RPM, or at least doesn't provide a way to expose the units used...
For RPM-controlled, look at the following entry instead:
fan[1-*]_target
Desired fan speed
Unit: revolution/min (RPM)
RW
Only makes sense if the chip supports closed-loop fan speed control based on the measured fan speed.
One significant difference is that, in this case, you always know which fan you control, while in the pwm[1-*] case you don't.
Signature · 6 lines
Jean Delvare _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Hi Jean !
Quoted 7 lines
In your case, the file would have only 3 possible values, with "off" mapping to 0, and "slow" and "fast" mapping to arbitrary positive values, like 64 and 192 or whatever you think is suitable. I understand that in your case, you don't really control the PWM output directly, but we do not have any interface for this, and I don't think there would be much value in adding one.
Quoted 5 lines
That being said, I am also only mildly convinced that fitting your chip in the standard pwm1 interface will be very helpful. I don't really expect tools such as the fancontrol script to behave properly when the pwm1 file only support a small number of discrete values. So the benefit of using the standard file name and semantics seems thin.
Yes, I'm not too sure either.
Quoted 9 lines
Quoted 6 lines
Another comment while at it is when implementing the thermal control for PowerMacs a while back (windfarm etc...) I had to deal with two different type of interfaces to fans. RPM controlled and PWM controlled.
The later basically let me program a percentile value (a percent of the duty cycle).
This is exactly what pwm[1-*] files are about, except that we used range 0-255 instead of 0-100 for historical and practical reasons.
Ok, I missed those in the doco.
Quoted 12 lines
Quoted 2 lines
I looks like the described sysfs interface only does RPM, or at least doesn't provide a way to expose the units used...
For RPM-controlled, look at the following entry instead:
fan[1-*]_target
Desired fan speed
Unit: revolution/min (RPM)
RW
Only makes sense if the chip supports closed-loop fan speed control based on the measured fan speed.
Quoted 2 lines
One significant difference is that, in this case, you always know which fan you control, while in the pwm[1-*] case you don't.
Right.
Now, maybe the best option is to have instead:
fan[1-*]_discrete_value
Discrete value
RW
fan[1-*]_supported values
List of supported discrete values
ROIE. I like the interface to be self-explanatory rather than relying on the user to know in advance what to write there. In which case I could either use 0,1,2 as values or even "off, slow, fast".
I can then make a custom fancontrol script (or add a wart to the existing one) to deal with this HW.
What do you think ?
Another option of course is to do the whole thermal control in a kernel thread :-) That wouldn't be very hard nor take a lot of code, but I'm sure I'll encounter resistance trying to merge that :-)
Cheers,
Ben.
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Hi Ben,
Sorry for the delay.
Quoted 24 lines · Benjamin Herrenschmidt
Quoted 11 lines
For RPM-controlled, look at the following entry instead:
fan[1-*]_target
Desired fan speed
Unit: revolution/min (RPM)
RW
Only makes sense if the chip supports closed-loop fan speed control based on the measured fan speed.One significant difference is that, in this case, you always know which fan you control, while in the pwm[1-*] case you don't.
Right.
Now, maybe the best option is to have instead:
fan[1-*]_discrete_value Discrete value RW fan[1-*]_supported values List of supported discrete values RO
Quoted 3 lines
IE. I like the interface to be self-explanatory rather than relying on the user to know in advance what to write there. In which case I could either use 0,1,2 as values or even "off, slow, fast".
I have no objection.
Quoted 4 lines
I can then make a custom fancontrol script (or add a wart to the existing one) to deal with this HW.
What do you think ?
Please don't try to add this to the fancontrol script. It's messy enough as is ;) You probably want to implement the kernel part and the user-space part together before you propose a standard interface, otherwise it might be difficult to make the best decisions with regards to attribute names and values.
Quoted 3 lines
Another option of course is to do the whole thermal control in a kernel thread :-) That wouldn't be very hard nor take a lot of code, but I'm sure I'll encounter resistance trying to merge that :-)
Me, I wouldn't object. That's what you did for other systems as far as I can see? As long as things work in the end, I have no problem with fan speed control being in the kernel. Having it in user-space has its share of issues (e.g. risk of overheating is the script dies for any reason.)
But yes, others may complain.
Signature · 6 lines
Jean Delvare _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Hi!
Quoted 11 lines
Right.
Now, maybe the best option is to have instead:
fan[1-*]_discrete_value Discrete value RW fan[1-*]_supported values List of supported discrete values RO
Hmm, for 100 different values, that will get ugly. What about simple fan_max file with values 0..fan_max being valid?
IIRC thinkpads have 8-or-so possible discrete cases...
Signature · 7 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Hi Pavel,
Quoted 10 lines · Pavel Machek
Hi!
Quoted 8 lines
Right.
Now, maybe the best option is to have instead:
fan[1-*]_discrete_value Discrete value RW
Quoted 6 lines
Quoted 3 lines
fan[1-*]_supported values
List of supported discrete values
ROHmm, for 100 different values, that will get ugly. What about simple
fan_maxfile with values 0..fan_max being valid?
If you have 100 different values, you can map them to the standard 0..255 range of pwm[1-*] files.
Quoted 1 line
IIRC thinkpads have 8-or-so possible discrete cases...
Correct. And even these would map nicely to the 0..255 range IMHO.
Signature · 6 lines
Jean Delvare _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Quoted 6 lines · Jean Delvare
If you have 100 different values, you can map them to the standard 0..255 range of pwm[1-*] files.
Quoted 1 line
IIRC thinkpads have 8-or-so possible discrete cases...
Correct. And even these would map nicely to the 0..255 range IMHO.
well, I eventually settled for doing that with my 3 values :-) We'll see how fan-control copes.
Cheers,
Ben.
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Quoted 10 lines · Benjamin Herrenschmidt
Now, maybe the best option is to have instead:
fan[1-*]_discrete_value
Discrete value
RWfan[1-*]_supported values
List of supported discrete values
RO
Perhaps a granularity (ie, step-size) instead of a full list of values?
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Quoted 9 lines · Ray Lee
Quoted 6 lines · Benjamin Herrenschmidt
Now, maybe the best option is to have instead:
fan[1-*]_discrete_value Discrete value RW
Quoted 6 lines
Quoted 4 lines
fan[1-*]_supported values
List of supported discrete values
ROPerhaps a granularity (ie, step-size) instead of a full list of values?
A possible addition to the current API, yes. But it may not cover all
cases: the step size isn't necessarily constant.
Signature · 6 lines
Jean Delvare _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors