Skip to contentSkip to conversation

Use lmb with x86

PATCH In review Yinghai Lu 3 participants 43 messages May 14, 2010 – May 17, 2010

Subsystems (13)
lore
Share & tools
lore

Yinghai Lu

author
#0 lore raw

cover Use lmb with x86

the new lmb could be used to replace early_res in x86.

Suggested by: David, Ben, and Thomas

-v6: change sequence as requested by Thomas
-v7: seperate them to more patches
-v8: add boundary checking to make sure not free partial page. -v9: use lmb_debug to control print out of reserve_lmb.
add e820 clean up, and e820 become __initdata
-v10:use lmb.rmo_size and ARCH_DISCARD_LMB according to Michael
change name to lmb_find_area/reserve_lmb_area/free_lmb_area,
according to Michael
update find_lmb_area to use __lmb_alloc_base according to ben
-v11:move find_lmb_area_size back to x86.
x86 has own find_lmb_area, and could be disabled by ARCH_LMB_FIND_AREA
because _lmb_find_base has different behavoir from x86's old one. one from high to high and one from low to high
need more test
tested for x86 32bit/64bit, numa/nonuma, nobootmem/bootmem.
-v12:refresh the series with current tip
seperate nobootmem.c, so could remove some #ifdef
still keep CONFIG_NO_BOOTMEM, in x86 .c, and could use the as tags so other lmb could refer them to use NO_BOOTMEM.

-v14:refresh to current tip

-v15:remove x86 version lmb_find_area
remove other nobootmem and x86 e820 from this patchset

-v16: rebase to Ben's cleanup powerpc/lmb
move back most func back to arch/x86/mm/lmb.c

-v17: remove exposing of lmb_add_region
seperate first lmb core related patch to several small patches.

this patcheset is based on tip/master+powerpc/lmb

todo:
1. use for_each_lmb to replace for cycle
2. replace range handling with lmb.
3. kill __lmb_find_area and use lmb_find_area directly

Thanks

Yinghai

author
#1 lore raw

PATCH 1/37 lmb: lmb_find_base() should return LMB_ERROR on failing path

all callees assume it return LMB_ERROR when it fail to find a range

---
 lib/lmb.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)
lib/lmb.c +1 -1
index 2cd5aaa..0d4e4c0 100644
@@ -154,7 +154,7 @@ static phys_addr_t __init lmb_find_base(phys_addr_t size, phys_addr_t align,
 		if (found != LMB_ERROR)
 			return found;
 	}
-	return 0;
+	return LMB_ERROR;
 }
 
 static void lmb_remove_region(struct lmb_type *type, unsigned long r)
Signature · 1 line
1.6.4.2
author
#2 lore raw

PATCH 2/37 lmb: Prepare x86 to use lmb to replace early_res

In reply to Yinghai Lu

1. expose lmb_debug
2. expose lmb_reserved_init_regions

-v2: drop lmb_add_region() and LMB_ERROR export -v3: seperate wrong return of lmb_fin_base to another patch

---
 include/linux/lmb.h |    2 ++
 lib/lmb.c           |    4 ++--
 2 files changed, 4 insertions(+), 2 deletions(-)
include/linux/lmb.h +2 -0
index 6f8c4bd..d88c92d 100644
@@ -39,6 +39,8 @@ struct lmb {
 };
 
 extern struct lmb lmb;
+extern int lmb_debug;
+extern struct lmb_region lmb_reserved_init_regions[];
 
 extern void __init lmb_init(void);
 extern void __init lmb_analyze(void);
lib/lmb.c +2 -2
index 0d4e4c0..b6725d6 100644
@@ -22,9 +22,9 @@
 
 struct lmb lmb;
 
-static int lmb_debug;
+int lmb_debug;
 static struct lmb_region lmb_memory_init_regions[INIT_LMB_REGIONS + 1];
-static struct lmb_region lmb_reserved_init_regions[INIT_LMB_REGIONS + 1];
+struct lmb_region lmb_reserved_init_regions[INIT_LMB_REGIONS + 1];
 
 #define LMB_ERROR	(~(phys_addr_t)0)
 
Signature · 1 line
1.6.4.2
author
#3 lore raw

PATCH 3/37 lmb: Print new doubled array location info

In reply to Yinghai Lu

so will have more idea where it is, use lmb_debug to controll it

---
 lib/lmb.c |    6 ++++--
 1 files changed, 4 insertions(+), 2 deletions(-)
lib/lmb.c +4 -2
index b6725d6..2bdbe87 100644
@@ -185,8 +185,6 @@ static int lmb_double_array(struct lmb_type *type)
 	phys_addr_t old_size, new_size, addr;
 	int use_slab = slab_is_available();
 
-	pr_debug("lmb: %s array full, doubling...", lmb_type_name(type));
-
 	/* Calculate new doubled size */
 	old_size = type->max * sizeof(struct lmb_region);
 	new_size = old_size << 1;
@@ -214,6 +212,10 @@ static int lmb_double_array(struct lmb_type *type)
 	}
 	new_array = __va(addr);
 
+	if (lmb_debug)
+		pr_info("lmb: %s array is doubled to %ld at %llx - %llx",
+			 lmb_type_name(type), type->max * 2, (u64)addr, (u64)addr + new_size);
+
 	/* Found space, we now need to move the array over before
 	 * we add the reserved region since it may be our reserved
 	 * array itself that is full.
Signature · 1 line
1.6.4.2
author
#4 lore raw

PATCH 4/37 lmb: Export LMB_ERROR again

In reply to Yinghai Lu

will used by x86 lmb_find_area_node and nobootmem replacement

---
 include/linux/lmb.h |    1 +
 lib/lmb.c           |    2 --
 2 files changed, 1 insertions(+), 2 deletions(-)
include/linux/lmb.h +1 -0
index d88c92d..d959d23 100644
@@ -19,6 +19,7 @@
 #include <asm/lmb.h>
 
 #define INIT_LMB_REGIONS 128
+#define LMB_ERROR	(~(phys_addr_t)0)
 
 struct lmb_region {
 	phys_addr_t base;
lib/lmb.c +0 -2
index 2bdbe87..3caf58c 100644
@@ -26,8 +26,6 @@ int lmb_debug;
 static struct lmb_region lmb_memory_init_regions[INIT_LMB_REGIONS + 1];
 struct lmb_region lmb_reserved_init_regions[INIT_LMB_REGIONS + 1];
 
-#define LMB_ERROR	(~(phys_addr_t)0)
-
 /* inline so we don't get a warning when pr_debug is compiled out */
 static inline const char *lmb_type_name(struct lmb_type *type)
 {
Signature · 1 line
1.6.4.2
author
#5 lore raw

PATCH 5/37 lmb: Prepare to include linux/lmb.h in core file

In reply to Yinghai Lu

Need to add protection in linux/lmb.h, to prepare to include it in
mm/page_alloc.c and mm/bootmem.c etc.

---
 include/linux/lmb.h |    3 +++
 1 files changed, 3 insertions(+), 0 deletions(-)
include/linux/lmb.h +3 -0
index d959d23..4c9c84a 100644
@@ -2,6 +2,7 @@
 #define _LINUX_LMB_H
 #ifdef __KERNEL__
 
+#ifdef CONFIG_HAVE_LMB
 /*
  * Logical memory blocks.
  *
@@ -143,6 +144,8 @@ static inline unsigned long lmb_region_pages(const struct lmb_region *reg)
 	     region++)
 
 
+#endif /* CONFIG_HAVE_LMB */
+
 #endif /* __KERNEL__ */
 
 #endif /* _LINUX_LMB_H */
Signature · 1 line
1.6.4.2
author
#6 lore raw

PATCH 6/37 lmb: Add ARCH_DISCARD_LMB to put lmb code to .init

In reply to Yinghai Lu

So those lmb bits could be released after kernel is booted up.

Arch code could define ARCH_DISCARD_LMB in asm/lmb.h, __init_lmb will become __init, __initdata_lmb will becom __initdata

x86 code will use that.

if ARCH_DISCARD_LMB is defined, debugfs is not used

-v2: use ARCH_DISCARD_LMB according to Michael Ellerman

---
 include/linux/lmb.h |    8 ++++++++
 lib/lmb.c           |   46 +++++++++++++++++++++++-----------------------
 2 files changed, 31 insertions(+), 23 deletions(-)
include/linux/lmb.h +8 -0
index 4c9c84a..e54c1d0 100644
@@ -144,6 +144,14 @@ static inline unsigned long lmb_region_pages(const struct lmb_region *reg)
 	     region++)
 
 
+#ifdef ARCH_DISCARD_LMB
+#define __init_lmb __init
+#define __initdata_lmb __initdata
+#else
+#define __init_lmb
+#define __initdata_lmb
+#endif
+
 #endif /* CONFIG_HAVE_LMB */
 
 #endif /* __KERNEL__ */
lib/lmb.c +23 -23

160 lines not on this page · raw message

Signature · 1 line
1.6.4.2
author
#7 lore raw

PATCH 7/37 lmb: Add lmb_find_area()

In reply to Yinghai Lu

it is a wrapper for lmb_find_base

make it more easy for x86 to use lmb. ( rebase ) x86 early_res is using find/reserve pattern instead of alloc.

keep it in weak version, so later We can use x86 own version if needed. also We need it in lib/lmb.c, so one called mm/page_alloc.c could get compiled

-v2: Change name to lmb_find_area() according to Michael Ellerman -v3: Add generic weak version __lmb_find_area()
so keep the path for fallback to x86 version that handle from low
-v4: use 0 for failing path
-v5: use LMB_ERROR again

---
 include/linux/lmb.h |    4 ++++
 lib/lmb.c           |   23 +++++++++++++++++++++++
 2 files changed, 27 insertions(+), 0 deletions(-)
include/linux/lmb.h +4 -0
index e54c1d0..c05294f 100644
@@ -44,6 +44,10 @@ extern struct lmb lmb;
 extern int lmb_debug;
 extern struct lmb_region lmb_reserved_init_regions[];
 
+u64 __lmb_find_area(u64 ei_start, u64 ei_last, u64 start, u64 end,
+			u64 size, u64 align);
+u64 lmb_find_area(u64 start, u64 end, u64 size, u64 align);
+
 extern void __init lmb_init(void);
 extern void __init lmb_analyze(void);
 extern long lmb_add(phys_addr_t base, phys_addr_t size);
lib/lmb.c +23 -0
index c92034b..1c46336 100644
@@ -155,6 +155,29 @@ static phys_addr_t __init lmb_find_base(phys_addr_t size, phys_addr_t align,
 	return LMB_ERROR;
 }
 
+u64 __init __weak __lmb_find_area(u64 ei_start, u64 ei_last, u64 start, u64 end,
+				 u64 size, u64 align)
+{
+	u64 final_start, final_end;
+	u64 mem;
+
+	final_start = max(ei_start, start);
+	final_end = min(ei_last, end);
+
+	if (final_start >= final_end)
+		return LMB_ERROR;
+
+	return  lmb_find_base(size, align, final_start, final_end);
+}
+
+/*
+ * Find a free area with specified alignment in a specific range.
+ */
+u64 __init __weak lmb_find_area(u64 start, u64 end, u64 size, u64 align)
+{
+	return lmb_find_base(size, align, start, end);
+}
+
 static void __init_lmb lmb_remove_region(struct lmb_type *type, unsigned long r)
 {
 	unsigned long i;
Signature · 1 line
1.6.4.2
#8 lore raw

Re: [PATCH 07/37] lmb: Add lmb_find_area()

Quoted 7 lines · Yinghai Lu

it is a wrapper for lmb_find_base

make it more easy for x86 to use lmb. ( rebase ) x86 early_res is using find/reserve pattern instead of alloc.

keep it in weak version, so later We can use x86 own version if needed. also We need it in lib/lmb.c, so one called mm/page_alloc.c could get compiled

I seem to have told you that I didn't want to have that thing in the core :-)

You keep adding those "wrappers" which basically just do prototype adaptation and in this case a bit of cropping, with a name that is utterly confusing as to what their intent is.

I might have accepted that one if you had called it something like lmb_find_in_range() which at least -means- something.

Cheers,
Ben.

Quoted 61 lines
(quoted diff) +0 -4
-v2: Change name to lmb_find_area() according to Michael Ellerman
-v3: Add generic weak version __lmb_find_area()
     so keep the path for fallback to x86 version that handle from low
-v4: use 0 for failing path
-v5: use LMB_ERROR again
---
 include/linux/lmb.h |    4 ++++
 lib/lmb.c           |   23 +++++++++++++++++++++++
 2 files changed, 27 insertions(+), 0 deletions(-)
include/linux/lmb.h +4 -0
index e54c1d0..c05294f 100644
@@ -44,6 +44,10 @@ extern struct lmb lmb;
 extern int lmb_debug;
 extern struct lmb_region lmb_reserved_init_regions[];
 
+u64 __lmb_find_area(u64 ei_start, u64 ei_last, u64 start, u64 end,
+			u64 size, u64 align);
+u64 lmb_find_area(u64 start, u64 end, u64 size, u64 align);
+
 extern void __init lmb_init(void);
 extern void __init lmb_analyze(void);
 extern long lmb_add(phys_addr_t base, phys_addr_t size);
lib/lmb.c +23 -0
index c92034b..1c46336 100644
@@ -155,6 +155,29 @@ static phys_addr_t __init lmb_find_base(phys_addr_t size, phys_addr_t align,
 	return LMB_ERROR;
 }
 
+u64 __init __weak __lmb_find_area(u64 ei_start, u64 ei_last, u64 start, u64 end,
+				 u64 size, u64 align)
+{
+	u64 final_start, final_end;
+	u64 mem;
+
+	final_start = max(ei_start, start);
+	final_end = min(ei_last, end);
+
+	if (final_start >= final_end)
+		return LMB_ERROR;
+
+	return  lmb_find_base(size, align, final_start, final_end);
+}
+
+/*
+ * Find a free area with specified alignment in a specific range.
+ */
+u64 __init __weak lmb_find_area(u64 start, u64 end, u64 size, u64 align)
+{
+	return lmb_find_base(size, align, start, end);
+}
+
 static void __init_lmb lmb_remove_region(struct lmb_type *type, unsigned long r)
 {
 	unsigned long i;
#9 lore raw

Re: [PATCH 07/37] lmb: Add lmb_find_area()

Quoted 12 lines · Benjamin Herrenschmidt
Quoted 7 lines · Yinghai Lu

it is a wrapper for lmb_find_base

make it more easy for x86 to use lmb. ( rebase ) x86 early_res is using find/reserve pattern instead of alloc.

keep it in weak version, so later We can use x86 own version if needed. also We need it in lib/lmb.c, so one called mm/page_alloc.c could get compiled

I seem to have told you that I didn't want to have that thing in the core :-)

Quoted 6 lines

You keep adding those "wrappers" which basically just do prototype adaptation and in this case a bit of cropping, with a name that is utterly confusing as to what their intent is.

I might have accepted that one if you had called it something like lmb_find_in_range() which at least -means- something.

thanks. will use sed to replace them.

lmb_find_area ==> lmb_find_in_range()

how about
lmb_reserve_area ==> lmb_reserve_range
lmb_free_area ==> lmb_free_range
or leave them that way, later replace them lmb_reserve and lmb_free one by one?

YH

#10 lore raw

Re: [PATCH 07/37] lmb: Add lmb_find_area()

Quoted 9 lines · Yinghai
Quoted 3 lines · Benjamin Herrenschmidt

I might have accepted that one if you had called it something like lmb_find_in_range() which at least -means- something.

thanks. will use sed to replace them.

lmb_find_area ==> lmb_find_in_range()

updated version is in

git://git.kernel.org/pub/scm/linux/kernel/git/yinghai/linux-2.6-yinghai.git lmb

it is on top of tip/master + powerpc/lmb

Thanks

Yinghai

#11 lore raw

Re: [PATCH 07/37] lmb: Add lmb_find_area()

In reply to Yinghai
Quoted 3 lines · Yinghai

how about
lmb_reserve_area ==> lmb_reserve_range
lmb_free_area ==> lmb_free_range

I completely fail to see why you still need those two. They are exactly the same thing as lmb_reserve() and lmb_free(), just with a slightly different prototype.

Quoted 2 lines

or leave them that way, later replace them lmb_reserve and lmb_free one by one?

Nah, if you have some use of the wrappers to ease the transition from the existing x86 code, then just make up a couple of inline wrappers somewhere inside the x86 code. You may not even want to call it lmb_* at all...

But here, I'll let Thomas and Peter decide what to do, it's really x86 stuff at this stage. I don't want to see two subtlely different APIs at the LMB level doing the same thing.

Cheers,
Ben.

#12 lore raw

Re: [PATCH 07/37] lmb: Add lmb_find_area()

Quoted 9 lines · Benjamin Herrenschmidt
Quoted 3 lines · Yinghai

how about
lmb_reserve_area ==> lmb_reserve_range
lmb_free_area ==> lmb_free_range

I completely fail to see why you still need those two. They are exactly the same thing as lmb_reserve() and lmb_free(), just with a slightly different prototype.

Quoted 7 lines
Quoted 2 lines

or leave them that way, later replace them lmb_reserve and lmb_free one by one?

Nah, if you have some use of the wrappers to ease the transition from the existing x86 code, then just make up a couple of inline wrappers somewhere inside the x86 code. You may not even want to call it lmb_* at all...

can you move asm/lmb.h down in linux/lmb.h ?

so I can put the inline wrapper in arch/x86/include/asm/lmb.h.

Quoted 9 lines

But here, I'll let Thomas and Peter decide what to do, it's really x86 stuff at this stage. I don't want to see two subtlely different APIs at the LMB level doing the same thing.

Cheers,
Ben.

author
#13 lore raw

PATCH 8/37 x86, lmb: Add lmb_find_area_size()

In reply to Yinghai Lu

size is returned according free range.
Will be used to find free ranges for early_memtest and memory corruption check

Do not mess it up with lib/lmb.c yet.

---
 arch/x86/include/asm/lmb.h |    8 ++++
 arch/x86/mm/Makefile       |    2 +
 arch/x86/mm/lmb.c          |   88 ++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 98 insertions(+), 0 deletions(-)
 create mode 100644 arch/x86/include/asm/lmb.h
 create mode 100644 arch/x86/mm/lmb.c
arch/x86/include/asm/lmb.h new file +8 -0
new file mode 100644
index 0000000..aa3a66e
@@ -0,0 +1,8 @@
+#ifndef _X86_LMB_H
+#define _X86_LMB_H
+
+#define ARCH_DISCARD_LMB
+
+u64 lmb_find_area_size(u64 start, u64 *sizep, u64 align);
+
+#endif
arch/x86/mm/Makefile +2 -0
index a4c7683..8ab0505 100644
@@ -26,4 +26,6 @@ obj-$(CONFIG_NUMA)		+= numa.o numa_$(BITS).o
 obj-$(CONFIG_K8_NUMA)		+= k8topology_64.o
 obj-$(CONFIG_ACPI_NUMA)		+= srat_$(BITS).o
 
+obj-$(CONFIG_HAVE_LMB)		+= lmb.o
+
 obj-$(CONFIG_MEMTEST)		+= memtest.o
arch/x86/mm/lmb.c new file +88 -0

88 lines not on this page · raw message

Signature · 1 line
1.6.4.2
author
#14 lore raw

PATCH 9/37 bootmem, x86: Add weak version of reserve_bootmem_generic

In reply to Yinghai Lu

It will be used lmb_to_bootmem converting

It is an wrapper for reserve_bootmem, and x86 64bit is using special one.

Also clean up that version for x86_64. We don't need to take care of numa path for that, bootmem can handle it how

---
 arch/x86/mm/init_32.c |    6 ------
 arch/x86/mm/init_64.c |   20 ++------------------
 mm/bootmem.c          |    6 ++++++
 3 files changed, 8 insertions(+), 24 deletions(-)
arch/x86/mm/init_32.c +0 -6
index bca7909..90e0545 100644
@@ -1069,9 +1069,3 @@ void mark_rodata_ro(void)
 #endif
 }
 #endif
-
-int __init reserve_bootmem_generic(unsigned long phys, unsigned long len,
-				   int flags)
-{
-	return reserve_bootmem(phys, len, flags);
-}
arch/x86/mm/init_64.c +2 -18
index ee41bba..634fa08 100644
@@ -799,13 +799,10 @@ void mark_rodata_ro(void)
 
 #endif
 
+#ifndef CONFIG_NO_BOOTMEM
 int __init reserve_bootmem_generic(unsigned long phys, unsigned long len,
 				   int flags)
 {
-#ifdef CONFIG_NUMA
-	int nid, next_nid;
-	int ret;
-#endif
 	unsigned long pfn = phys >> PAGE_SHIFT;
 
 	if (pfn >= max_pfn) {
@@ -821,21 +818,7 @@ int __init reserve_bootmem_generic(unsigned long phys, unsigned long len,
 		return -EFAULT;
 	}
 
-	/* Should check here against the e820 map to avoid double free */
-#ifdef CONFIG_NUMA
-	nid = phys_to_nid(phys);
-	next_nid = phys_to_nid(phys + len - 1);
-	if (nid == next_nid)
-		ret = reserve_bootmem_node(NODE_DATA(nid), phys, len, flags);
-	else
-		ret = reserve_bootmem(phys, len, flags);
-
-	if (ret != 0)
-		return ret;
-
-#else
 	reserve_bootmem(phys, len, flags);
-#endif
 
 	if (phys+len <= MAX_DMA_PFN*PAGE_SIZE) {
 		dma_reserve += len / PAGE_SIZE;
@@ -844,6 +827,7 @@ int __init reserve_bootmem_generic(unsigned long phys, unsigned long len,
 
 	return 0;
 }
+#endif
 
 int kern_addr_valid(unsigned long addr)
 {
mm/bootmem.c +6 -0
index 58c66cc..ee31b95 100644
@@ -526,6 +526,12 @@ int __init reserve_bootmem(unsigned long addr, unsigned long size,
 }
 
 #ifndef CONFIG_NO_BOOTMEM
+int __weak __init reserve_bootmem_generic(unsigned long phys, unsigned long len,
+				   int flags)
+{
+	return reserve_bootmem(phys, len, flags);
+}
+
 static unsigned long __init align_idx(struct bootmem_data *bdata,
 				      unsigned long idx, unsigned long step)
 {
Signature · 1 line
1.6.4.2
author
#15 lore raw

PATCH 10/37 x86, lmb: Add lmb_to_bootmem()

In reply to Yinghai Lu

lmb_to_bootmem() will reserve lmb.reserved.region in bootmem after bootmem is set up.

We can use it to with all arches that support lmb later.

---
 arch/x86/include/asm/lmb.h |    1 +
 arch/x86/mm/lmb.c          |   31 +++++++++++++++++++++++++++++++
 2 files changed, 32 insertions(+), 0 deletions(-)
arch/x86/include/asm/lmb.h +1 -0
index aa3a66e..2f06714 100644
@@ -4,5 +4,6 @@
 #define ARCH_DISCARD_LMB
 
 u64 lmb_find_area_size(u64 start, u64 *sizep, u64 align);
+void lmb_to_bootmem(u64 start, u64 end);
 
 #endif
arch/x86/mm/lmb.c +31 -0
index 9d26eed..37a05e2 100644
@@ -86,3 +86,34 @@ u64 __init lmb_find_area_size(u64 start, u64 *sizep, u64 align)
 	return LMB_ERROR;
 }
 
+#ifndef CONFIG_NO_BOOTMEM
+void __init lmb_to_bootmem(u64 start, u64 end)
+{
+	int i, count;
+	u64 final_start, final_end;
+
+	/* Take out region array itself */
+	if (lmb.reserved.regions != lmb_reserved_init_regions)
+		lmb_free(__pa(lmb.reserved.regions), sizeof(struct lmb_region) * lmb.reserved.max);
+
+	count  = lmb.reserved.cnt;
+	pr_info("(%d early reservations) ==> bootmem [%010llx - %010llx]\n", count, start, end);
+	for (i = 0; i < count; i++) {
+		struct lmb_region *r = &lmb.reserved.regions[i];
+		pr_info("  #%d [%010llx - %010llx] ", i, (u64)r->base, (u64)r->base + r->size);
+		final_start = max(start, r->base);
+		final_end = min(end, r->base + r->size);
+		if (final_start >= final_end) {
+			pr_cont("\n");
+			continue;
+		}
+		pr_cont(" ==> [%010llx - %010llx]\n", final_start, final_end);
+		reserve_bootmem_generic(final_start, final_end - final_start, BOOTMEM_DEFAULT);
+	}
+	/* Clear them to avoid misusing ? */
+	memset(&lmb.reserved.regions[0], 0, sizeof(struct lmb_region) * lmb.reserved.max);
+	lmb.reserved.regions = NULL;
+	lmb.reserved.max = 0;
+	lmb.reserved.cnt = 0;
+}
+#endif
Signature · 1 line
1.6.4.2
author
#16 lore raw

PATCH 11/37 x86,lmb: Add lmb_reserve_area/lmb_free_area

In reply to Yinghai Lu

they are wrappers for core versions.
they are taking start/end/name instead of base/size. will make x86 conversion more easy

could add more debug print out

-v2: change get_max_mapped() to lmb.default_alloc_limit according to Michael
Ellerman and Ben
change to lmb_reserve_area and lmb_free_area according to Michael Ellerman
-v3: call check_and_double after reserve/free, so could avoid to use
find_lmb_area. Suggested by Michael Ellerman

---
 arch/x86/include/asm/lmb.h |    4 ++++
 arch/x86/mm/lmb.c          |   27 +++++++++++++++++++++++++++
 2 files changed, 31 insertions(+), 0 deletions(-)
arch/x86/include/asm/lmb.h +4 -0
index 2f06714..bc85c1e 100644
@@ -6,4 +6,8 @@
 u64 lmb_find_area_size(u64 start, u64 *sizep, u64 align);
 void lmb_to_bootmem(u64 start, u64 end);
 
+void lmb_reserve_area(u64 start, u64 end, char *name);
+void lmb_free_area(u64 start, u64 end);
+void lmb_add_memory(u64 start, u64 end);
+
 #endif
arch/x86/mm/lmb.c +27 -0
index 37a05e2..5d0b008 100644
@@ -117,3 +117,30 @@ void __init lmb_to_bootmem(u64 start, u64 end)
 	lmb.reserved.cnt = 0;
 }
 #endif
+
+void __init lmb_add_memory(u64 start, u64 end)
+{
+	lmb_add(start, end - start);
+}
+
+void __init lmb_reserve_area(u64 start, u64 end, char *name)
+{
+	if (start == end)
+		return;
+
+	if (WARN_ONCE(start > end, "lmb_reserve_area: wrong range [%#llx, %#llx]\n", start, end))
+		return;
+
+	lmb_reserve(start, end - start);
+}
+
+void __init lmb_free_area(u64 start, u64 end)
+{
+	if (start == end)
+		return;
+
+	if (WARN_ONCE(start > end, "lmb_free_area: wrong range [%#llx, %#llx]\n", start, end))
+		return;
+
+	lmb_free(start, end - start);
+}
Signature · 1 line
1.6.4.2
author
#17 lore raw

PATCH 12/37 x86, lmb: Add get_free_all_memory_range()

In reply to Yinghai Lu

get_free_all_memory_range is for CONFIG_NO_BOOTMEM=y, and will be called by free_all_memory_core_early().

It will use early_node_map aka active ranges subtract lmb.reserved to get all free range, and those ranges will convert to slab pages.

-v4: increase range size

---
 arch/x86/include/asm/lmb.h |    2 +
 arch/x86/mm/lmb.c          |  110 +++++++++++++++++++++++++++++++++++++++++++-
 2 files changed, 111 insertions(+), 1 deletions(-)
arch/x86/include/asm/lmb.h +2 -0
index bc85c1e..80e9e4c 100644
@@ -9,5 +9,7 @@ void lmb_to_bootmem(u64 start, u64 end);
 void lmb_reserve_area(u64 start, u64 end, char *name);
 void lmb_free_area(u64 start, u64 end);
 void lmb_add_memory(u64 start, u64 end);
+struct range;
+int get_free_all_memory_range(struct range **rangep, int nodeid);
 
 #endif
arch/x86/mm/lmb.c +109 -1

116 lines not on this page · raw message

Signature · 1 line
1.6.4.2
author
#18 lore raw

PATCH 13/37 x86, lmb: Add lmb_register_active_regions() and lmb_hole_size()

In reply to Yinghai Lu

lmb_register_active_regions() will be used to fill early_node_map, the result will be lmb.memory.region AND numa data

lmb_hole_size will be used to find hole size on lmb.memory.region with specified range.

---
 arch/x86/include/asm/lmb.h |    4 ++
 arch/x86/mm/lmb.c          |   69 ++++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 73 insertions(+), 0 deletions(-)
arch/x86/include/asm/lmb.h +4 -0
index 80e9e4c..d0ae19f 100644
@@ -12,4 +12,8 @@ void lmb_add_memory(u64 start, u64 end);
 struct range;
 int get_free_all_memory_range(struct range **rangep, int nodeid);
 
+void lmb_register_active_regions(int nid, unsigned long start_pfn,
+					 unsigned long last_pfn);
+u64 lmb_hole_size(u64 start, u64 end);
+
 #endif
arch/x86/mm/lmb.c +69 -0

72 lines not on this page · raw message

Signature · 1 line
1.6.4.2
author
#19 lore raw

PATCH 14/37 lmb: Add find_memory_core_early()

In reply to Yinghai Lu

According to node range in early_node_map[] with __lmb_find_area to find free range.

Will be used by lmb_find_area_node()

lmb_find_area_node will be used to find right buffer for NODE_DATA

---
 include/linux/mm.h |    2 ++
 mm/page_alloc.c    |   29 +++++++++++++++++++++++++++++
 2 files changed, 31 insertions(+), 0 deletions(-)
include/linux/mm.h +2 -0
index fb19bb9..7774e1d 100644
@@ -1159,6 +1159,8 @@ extern void free_bootmem_with_active_regions(int nid,
 						unsigned long max_low_pfn);
 int add_from_early_node_map(struct range *range, int az,
 				   int nr_range, int nid);
+u64 __init find_memory_core_early(int nid, u64 size, u64 align,
+					u64 goal, u64 limit);
 void *__alloc_memory_core_early(int nodeid, u64 size, u64 align,
 				 u64 goal, u64 limit);
 typedef int (*work_fn_t)(unsigned long, unsigned long, void *);
mm/page_alloc.c +29 -0
index d03c946..8f17f1f 100644
@@ -21,6 +21,7 @@
 #include <linux/pagemap.h>
 #include <linux/jiffies.h>
 #include <linux/bootmem.h>
+#include <linux/lmb.h>
 #include <linux/compiler.h>
 #include <linux/kernel.h>
 #include <linux/kmemcheck.h>
@@ -3393,6 +3394,34 @@ void __init free_bootmem_with_active_regions(int nid,
 	}
 }
 
+#ifdef CONFIG_HAVE_LMB
+u64 __init find_memory_core_early(int nid, u64 size, u64 align,
+					u64 goal, u64 limit)
+{
+	int i;
+
+	/* Need to go over early_node_map to find out good range for node */
+	for_each_active_range_index_in_nid(i, nid) {
+		u64 addr;
+		u64 ei_start, ei_last;
+
+		ei_last = early_node_map[i].end_pfn;
+		ei_last <<= PAGE_SHIFT;
+		ei_start = early_node_map[i].start_pfn;
+		ei_start <<= PAGE_SHIFT;
+		addr = __lmb_find_area(ei_start, ei_last,
+					 goal, limit, size, align);
+
+		if (addr == LMB_ERROR)
+			continue;
+
+		return addr;
+	}
+
+	return LMB_ERROR;
+}
+#endif
+
 int __init add_from_early_node_map(struct range *range, int az,
 				   int nr_range, int nid)
 {
Signature · 1 line
1.6.4.2
author
#20 lore raw

PATCH 15/37 x86, lmb: Add lmb_find_area_node()

In reply to Yinghai Lu

It can be used to find NODE_DATA for numa.

Need to make sure early_node_map[] is filled before it is called, otherwise it will fallback to lmb_find_area(), with node range.

---
 arch/x86/include/asm/lmb.h |    1 +
 arch/x86/mm/lmb.c          |   15 +++++++++++++++
 2 files changed, 16 insertions(+), 0 deletions(-)
arch/x86/include/asm/lmb.h +1 -0
index d0ae19f..358d8a6 100644
@@ -15,5 +15,6 @@ int get_free_all_memory_range(struct range **rangep, int nodeid);
 void lmb_register_active_regions(int nid, unsigned long start_pfn,
 					 unsigned long last_pfn);
 u64 lmb_hole_size(u64 start, u64 end);
+u64 lmb_find_area_node(int nid, u64 start, u64 end, u64 size, u64 align);
 
 #endif
arch/x86/mm/lmb.c +15 -0
index 11b76d0..17bb1fb 100644
@@ -254,6 +254,21 @@ void __init lmb_free_area(u64 start, u64 end)
 }
 
 /*
+ * Need to call this function after lmb_register_active_regions,
+ * so early_node_map[] is filled already.
+ */
+u64 __init lmb_find_area_node(int nid, u64 start, u64 end, u64 size, u64 align)
+{
+	u64 addr;
+	addr = find_memory_core_early(nid, size, align, start, end);
+	if (addr != LMB_ERROR)
+		return addr;
+
+	/* Fallback, should already have start end within node range */
+	return lmb_find_area(start, end, size, align);
+}
+
+/*
  * Finds an active region in the address range from start_pfn to last_pfn and
  * returns its range in ei_startpfn and ei_endpfn for the lmb entry.
  */
Signature · 1 line
1.6.4.2
author
#21 lore raw

PATCH 16/37 x86, lmb: Add lmb_free_memory_size()

In reply to Yinghai Lu

It will return free memory size in specified range.

We can not use memory_size - reserved_size here, because some reserved area may not be in the scope of lmb.memory.region.

Use lmb.memory.region subtracting lmb.reserved.region to get free range array. then count size of all free ranges.

---
 arch/x86/include/asm/lmb.h |    1 +
 arch/x86/mm/lmb.c          |   51 ++++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 52 insertions(+), 0 deletions(-)
arch/x86/include/asm/lmb.h +1 -0
index 358d8a6..4fb94b5 100644
@@ -16,5 +16,6 @@ void lmb_register_active_regions(int nid, unsigned long start_pfn,
 					 unsigned long last_pfn);
 u64 lmb_hole_size(u64 start, u64 end);
 u64 lmb_find_area_node(int nid, u64 start, u64 end, u64 size, u64 align);
+u64 lmb_free_memory_size(u64 addr, u64 limit);
 
 #endif
arch/x86/mm/lmb.c +51 -0

57 lines not on this page · raw message

Signature · 1 line
1.6.4.2
author
#22 lore raw

PATCH 17/37 x86, lmb: Add lmb_memory_size()

In reply to Yinghai Lu

It will return memory size in specified range according to lmb.memory.region

Try to share some code with lmb_free_memory_size() by passing get_free to __lmb_memory_size().

---
 arch/x86/include/asm/lmb.h |    1 +
 arch/x86/mm/lmb.c          |   18 +++++++++++++++++-
 2 files changed, 18 insertions(+), 1 deletions(-)
arch/x86/include/asm/lmb.h +1 -0
index 4fb94b5..dd42ac1 100644
@@ -17,5 +17,6 @@ void lmb_register_active_regions(int nid, unsigned long start_pfn,
 u64 lmb_hole_size(u64 start, u64 end);
 u64 lmb_find_area_node(int nid, u64 start, u64 end, u64 size, u64 align);
 u64 lmb_free_memory_size(u64 addr, u64 limit);
+u64 lmb_memory_size(u64 addr, u64 limit);
 
 #endif
arch/x86/mm/lmb.c +17 -1
index 3a16cdc..15fd3e4 100644
@@ -226,7 +226,7 @@ void __init lmb_to_bootmem(u64 start, u64 end)
 }
 #endif
 
-u64 __init lmb_free_memory_size(u64 addr, u64 limit)
+static u64 __init __lmb_memory_size(u64 addr, u64 limit, bool get_free)
 {
 	int i, count;
 	struct range *range;
@@ -256,6 +256,10 @@ u64 __init lmb_free_memory_size(u64 addr, u64 limit)
 	}
 	subtract_range(range, count, 0, addr);
 	subtract_range(range, count, limit, -1ULL);
+
+	/* Subtract lmb.reserved.region in range ? */
+	if (!get_free)
+		goto sort_and_count_them;
 	for (i = 0; i < lmb.reserved.cnt; i++) {
 		struct lmb_region *r = &lmb.reserved.regions[i];
 
@@ -268,6 +272,8 @@ u64 __init lmb_free_memory_size(u64 addr, u64 limit)
 
 		subtract_range(range, count, final_start, final_end);
 	}
+
+sort_and_count_them:
 	nr_range = clean_sort_range(range, count);
 
 	free_size = 0;
@@ -277,6 +283,16 @@ u64 __init lmb_free_memory_size(u64 addr, u64 limit)
 	return free_size << PAGE_SHIFT;
 }
 
+u64 __init lmb_free_memory_size(u64 addr, u64 limit)
+{
+	return __lmb_memory_size(addr, limit, true);
+}
+
+u64 __init lmb_memory_size(u64 addr, u64 limit)
+{
+	return __lmb_memory_size(addr, limit, false);
+}
+
 void __init lmb_add_memory(u64 start, u64 end)
 {
 	lmb_add(start, end - start);
Signature · 1 line
1.6.4.2
author
#23 lore raw

PATCH 18/37 x86, lmb: Use lmb_debug to control debug message print out

In reply to Yinghai Lu

Also let lmb_reserve_area/lmb_free_area could print out name if lmb=debug is specified

will also print ther name when reserve_lmb_area/free_lmb_area are called.

---
 arch/x86/mm/lmb.c |   24 ++++++++++++++++++------
 1 files changed, 18 insertions(+), 6 deletions(-)
arch/x86/mm/lmb.c +18 -6
index 15fd3e4..5007dbf 100644
@@ -121,11 +121,13 @@ static void __init subtract_lmb_reserved(struct range *range, int az)
 
 	count  = lmb.reserved.cnt;
 
-	pr_info("Subtract (%d early reservations)\n", count);
+	if (lmb_debug)
+		pr_info("Subtract (%d early reservations)\n", count);
 
 	for (i = 0; i < count; i++) {
 		struct lmb_region *r = &lmb.reserved.regions[i];
-		pr_info("  #%d [%010llx - %010llx]\n", i, (u64)r->base, (u64)r->base + r->size);
+		if (lmb_debug)
+			pr_info("  #%d [%010llx - %010llx]\n", i, (u64)r->base, (u64)r->base + r->size);
 		final_start = PFN_DOWN(r->base);
 		final_end = PFN_UP(r->base + r->size);
 		if (final_start >= final_end)
@@ -205,17 +207,21 @@ void __init lmb_to_bootmem(u64 start, u64 end)
 		lmb_free(__pa(lmb.reserved.regions), sizeof(struct lmb_region) * lmb.reserved.max);
 
 	count  = lmb.reserved.cnt;
-	pr_info("(%d early reservations) ==> bootmem [%010llx - %010llx]\n", count, start, end);
+	if (lmb_debug)
+		pr_info("(%d early reservations) ==> bootmem [%010llx - %010llx]\n", count, start, end);
 	for (i = 0; i < count; i++) {
 		struct lmb_region *r = &lmb.reserved.regions[i];
-		pr_info("  #%d [%010llx - %010llx] ", i, (u64)r->base, (u64)r->base + r->size);
+		if (lmb_debug)
+			pr_info("  #%d [%010llx - %010llx] ", i, (u64)r->base, (u64)r->base + r->size);
 		final_start = max(start, r->base);
 		final_end = min(end, r->base + r->size);
 		if (final_start >= final_end) {
-			pr_cont("\n");
+			if (lmb_debug)
+				pr_cont("\n");
 			continue;
 		}
-		pr_cont(" ==> [%010llx - %010llx]\n", final_start, final_end);
+		if (lmb_debug)
+			pr_cont(" ==> [%010llx - %010llx]\n", final_start, final_end);
 		reserve_bootmem_generic(final_start, final_end - final_start, BOOTMEM_DEFAULT);
 	}
 	/* Clear them to avoid misusing ? */
@@ -306,6 +312,9 @@ void __init lmb_reserve_area(u64 start, u64 end, char *name)
 	if (WARN_ONCE(start > end, "lmb_reserve_area: wrong range [%#llx, %#llx]\n", start, end))
 		return;
 
+	if (lmb_debug)
+		pr_info("    lmb_reserve_area: [%010llx, %010llx] %16s\n", start, end, name);
+
 	lmb_reserve(start, end - start);
 }
 
@@ -317,6 +326,9 @@ void __init lmb_free_area(u64 start, u64 end)
 	if (WARN_ONCE(start > end, "lmb_free_area: wrong range [%#llx, %#llx]\n", start, end))
 		return;
 
+	if (lmb_debug)
+		pr_info("       lmb_free_area: [%010llx, %010llx]\n", start, end);
+
 	lmb_free(start, end - start);
 }
 
Signature · 1 line
1.6.4.2
author
#24 lore raw

PATCH 19/37 x86, lmb: Add x86 version of __lmb_find_area()

In reply to Yinghai Lu

Generic version is going from high to low, and it seems it can not find right area compact enough.

the x86 version will go from goal to limit and just like the way We used for early_res

use ARCH_FIND_LMB_AREA to select from them.

-v2: default to no

---
 arch/x86/Kconfig  |    8 +++++
 arch/x86/mm/lmb.c |   78 +++++++++++++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 86 insertions(+), 0 deletions(-)
arch/x86/Kconfig +8 -0
index d80d2ab..36a5665 100644
@@ -584,6 +584,14 @@ config PARAVIRT_DEBUG
 	  Enable to debug paravirt_ops internals.  Specifically, BUG if
 	  a paravirt_op is missing when it is called.
 
+config ARCH_LMB_FIND_AREA
+	default n
+	bool "Use x86 own lmb_find_area()"
+	---help---
+	  Use lmb_find_area() version instead of generic version, it get free
+	  area up from low.
+	  Generic one try to get free area down from limit.
+
 config NO_BOOTMEM
 	default y
 	bool "Disable Bootmem code"
arch/x86/mm/lmb.c +78 -0

81 lines not on this page · raw message

Signature · 1 line
1.6.4.2
author
#25 lore raw

PATCH 20/37 x86: Use lmb to replace early_res

In reply to Yinghai Lu

1. replace find_e820_area with lmb_find_area
2. replace reserve_early with lmb_reserve_area
3. replace free_early with lmb_free_area.
4. NO_BOOTMEM will switch to use lmb too.
5. use _e820, _early wrap in the patch, in following patch, will replace them all
6. because lmb_free_area support partial free, we can remove some special care
7. Need to make sure that lmb_find_area() is called after fill_lmb_memory() so adjust some calling later in setup.c::setup_arch()
-- corruption_check and mptable_update

-v2: Move reserve_brk() early
Before fill_lmb_area, to avoid overlap between brk and lmb_find_area() that could happen We have more then 128 RAM entry in E820 tables, and fill_lmb_memory() could use lmb_find_area() to find a new place for lmb.memory.region array.
and We don't need to use extend_brk() after fill_lmb_area()
So move reserve_brk() early before fill_lmb_area().
-v3: Move find_smp_config early
To make sure lmb_find_area not find wrong place, if BIOS doesn't put mptable in right place.
-v4: Treat RESERVED_KERN as RAM in lmb.memory. and they are already in
lmb.reserved already..
use __NOT_KEEP_LMB to make sure lmb related code could be freed later.
-v5: Generic version __lmb_find_area() is going from high to low, and for 32bit
active_region for 32bit does include high pages
need to replace the limit with lmb.default_alloc_limit, aka get_max_mapped()
-v6: Use current_limit instead

---
 arch/x86/Kconfig               |    9 +--
 arch/x86/include/asm/e820.h    |   15 +++--
 arch/x86/kernel/check.c        |   14 ++--
 arch/x86/kernel/e820.c         |  153 ++++++++++++----------------------------
 arch/x86/kernel/head.c         |    3 +-
 arch/x86/kernel/head32.c       |    6 +-
 arch/x86/kernel/head64.c       |    3 +
 arch/x86/kernel/mpparse.c      |    5 +-
 arch/x86/kernel/setup.c        |   46 +++++++++----
 arch/x86/kernel/setup_percpu.c |    6 --
 arch/x86/mm/numa_64.c          |    5 +-
 kernel/Makefile                |    1 -
 mm/bootmem.c                   |    1 +
 mm/page_alloc.c                |   36 +++-------
 mm/sparse-vmemmap.c            |   11 ---
 15 files changed, 123 insertions(+), 191 deletions(-)
arch/x86/Kconfig +3 -6
index 36a5665..72763d8 100644
@@ -27,6 +27,7 @@ config X86
 	select HAVE_PERF_EVENTS if (!M386 && !M486)
 	select HAVE_IOREMAP_PROT
 	select HAVE_KPROBES
+	select HAVE_LMB
 	select ARCH_WANT_OPTIONAL_GPIOLIB
 	select ARCH_WANT_FRAME_POINTERS
 	select HAVE_DMA_ATTRS
@@ -193,9 +194,6 @@ config ARCH_SUPPORTS_OPTIMIZED_INLINING
 config ARCH_SUPPORTS_DEBUG_PAGEALLOC
 	def_bool y
 
-config HAVE_EARLY_RES
-	def_bool y
-
 config HAVE_INTEL_TXT
 	def_bool y
 	depends on EXPERIMENTAL && DMAR && ACPI
@@ -596,14 +594,13 @@ config NO_BOOTMEM
 	default y
 	bool "Disable Bootmem code"
 	---help---
-	  Use early_res directly instead of bootmem before slab is ready.
+	  Use lmb directly instead of bootmem before slab is ready.
 		- allocator (buddy) [generic]
 		- early allocator (bootmem) [generic]
-		- very early allocator (reserve_early*()) [x86]
+		- very early allocator (lmb) [some generic]
 		- very very early allocator (early brk model) [x86]
 	  So reduce one layer between early allocator to final allocator
 
-
 config MEMTEST
 	bool "Memtest"
 	---help---
arch/x86/include/asm/e820.h +9 -6
index ec8a52d..38adac8 100644
@@ -117,24 +117,27 @@ extern unsigned long end_user_pfn;
 extern u64 find_e820_area(u64 start, u64 end, u64 size, u64 align);
 extern u64 find_e820_area_size(u64 start, u64 *sizep, u64 align);
 extern u64 early_reserve_e820(u64 startt, u64 sizet, u64 align);
-#include <linux/early_res.h>
 
 extern unsigned long e820_end_of_ram_pfn(void);
 extern unsigned long e820_end_of_low_ram_pfn(void);
-extern int e820_find_active_region(const struct e820entry *ei,
-				  unsigned long start_pfn,
-				  unsigned long last_pfn,
-				  unsigned long *ei_startpfn,
-				  unsigned long *ei_endpfn);
 extern void e820_register_active_regions(int nid, unsigned long start_pfn,
 					 unsigned long end_pfn);
 extern u64 e820_hole_size(u64 start, u64 end);
+
+extern u64 early_reserve_e820(u64 startt, u64 sizet, u64 align);
+
+void init_lmb_memory(void);
+void fill_lmb_memory(void);
+
 extern void finish_e820_parsing(void);
 extern void e820_reserve_resources(void);
 extern void e820_reserve_resources_late(void);
 extern void setup_memory_map(void);
 extern char *default_machine_specific_memory_setup(void);
 
+void reserve_early(u64 start, u64 end, char *name);
+void free_early(u64 start, u64 end);
+
 /*
  * Returns true iff the specified range [s,e) is completely contained inside
  * the ISA region.
arch/x86/kernel/check.c +8 -6
index fc999e6..fcb3f11 100644
@@ -2,7 +2,8 @@
 #include <linux/sched.h>
 #include <linux/kthread.h>
 #include <linux/workqueue.h>
-#include <asm/e820.h>
+#include <linux/lmb.h>
+
 #include <asm/proto.h>
 
 /*
@@ -18,10 +19,12 @@ static int __read_mostly memory_corruption_check = -1;
 static unsigned __read_mostly corruption_check_size = 64*1024;
 static unsigned __read_mostly corruption_check_period = 60; /* seconds */
 
-static struct e820entry scan_areas[MAX_SCAN_AREAS];
+static struct scan_area {
+	u64 addr;
+	u64 size;
+} scan_areas[MAX_SCAN_AREAS];
 static int num_scan_areas;
 
-
 static __init int set_corruption_check(char *arg)
 {
 	char *end;
@@ -81,7 +84,7 @@ void __init setup_bios_corruption_check(void)
 
 	while (addr < corruption_check_size && num_scan_areas < MAX_SCAN_AREAS) {
 		u64 size;
-		addr = find_e820_area_size(addr, &size, PAGE_SIZE);
+		addr = lmb_find_area_size(addr, &size, PAGE_SIZE);
 
 		if (!(addr + 1))
 			break;
@@ -92,7 +95,7 @@ void __init setup_bios_corruption_check(void)
 		if ((addr + size) > corruption_check_size)
 			size = corruption_check_size - addr;
 
-		e820_update_range(addr, size, E820_RAM, E820_RESERVED);
+		lmb_reserve_area(addr, addr + size, "SCAN RAM");
 		scan_areas[num_scan_areas].addr = addr;
 		scan_areas[num_scan_areas].size = size;
 		num_scan_areas++;
@@ -105,7 +108,6 @@ void __init setup_bios_corruption_check(void)
 
 	printk(KERN_INFO "Scanning %d areas for low memory corruption\n",
 	       num_scan_areas);
-	update_e820();
 }
 
 
arch/x86/kernel/e820.c +44 -109

209 lines not on this page · raw message

arch/x86/kernel/head.c +2 -1
index 3e66bd3..c83a8d8 100644
@@ -1,5 +1,6 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
+#include <linux/lmb.h>
 
 #include <asm/setup.h>
 #include <asm/bios_ebda.h>
@@ -51,5 +52,5 @@ void __init reserve_ebda_region(void)
 		lowmem = 0x9f000;
 
 	/* reserve all memory between lowmem and the 1MB mark */
-	reserve_early_overlap_ok(lowmem, 0x100000, "BIOS reserved");
+	lmb_reserve_area(lowmem, 0x100000, "* BIOS reserved");
 }
arch/x86/kernel/head32.c +4 -2
index b2e2460..ab3e366 100644
@@ -8,6 +8,7 @@
 #include <linux/init.h>
 #include <linux/start_kernel.h>
 #include <linux/mm.h>
+#include <linux/lmb.h>
 
 #include <asm/setup.h>
 #include <asm/sections.h>
@@ -30,14 +31,15 @@ static void __init i386_default_early_setup(void)
 
 void __init i386_start_kernel(void)
 {
+	init_lmb_memory();
+
 #ifdef CONFIG_X86_TRAMPOLINE
 	/*
 	 * But first pinch a few for the stack/trampoline stuff
 	 * FIXME: Don't need the extra page at 4K, but need to fix
 	 * trampoline before removing it. (see the GDT stuff)
 	 */
-	reserve_early_overlap_ok(PAGE_SIZE, PAGE_SIZE + PAGE_SIZE,
-					 "EX TRAMPOLINE");
+	lmb_reserve_area(PAGE_SIZE, PAGE_SIZE + PAGE_SIZE, "EX TRAMPOLINE");
 #endif
 
 	reserve_early(__pa_symbol(&_text), __pa_symbol(&__bss_stop), "TEXT DATA BSS");
arch/x86/kernel/head64.c +3 -0
index 7147143..89dd2de 100644
@@ -12,6 +12,7 @@
 #include <linux/percpu.h>
 #include <linux/start_kernel.h>
 #include <linux/io.h>
+#include <linux/lmb.h>
 
 #include <asm/processor.h>
 #include <asm/proto.h>
@@ -96,6 +97,8 @@ void __init x86_64_start_kernel(char * real_mode_data)
 
 void __init x86_64_start_reservations(char *real_mode_data)
 {
+	init_lmb_memory();
+
 	copy_bootdata(__va(real_mode_data));
 
 	reserve_early(__pa_symbol(&_text), __pa_symbol(&__bss_stop), "TEXT DATA BSS");
arch/x86/kernel/mpparse.c +3 -2
index 5ae5d24..7cc6ad7 100644
@@ -11,6 +11,7 @@
 #include <linux/init.h>
 #include <linux/delay.h>
 #include <linux/bootmem.h>
+#include <linux/lmb.h>
 #include <linux/kernel_stat.h>
 #include <linux/mc146818rtc.h>
 #include <linux/bitops.h>
@@ -641,7 +642,7 @@ static void __init smp_reserve_memory(struct mpf_intel *mpf)
 {
 	unsigned long size = get_mpc_size(mpf->physptr);
 
-	reserve_early_overlap_ok(mpf->physptr, mpf->physptr+size, "MP-table mpc");
+	lmb_reserve_area(mpf->physptr, mpf->physptr+size, "* MP-table mpc");
 }
 
 static int __init smp_scan_config(unsigned long base, unsigned long length)
@@ -670,7 +671,7 @@ static int __init smp_scan_config(unsigned long base, unsigned long length)
 			       mpf, (u64)virt_to_phys(mpf));
 
 			mem = virt_to_phys(mpf);
-			reserve_early_overlap_ok(mem, mem + sizeof(*mpf), "MP-table mpf");
+			lmb_reserve_area(mem, mem + sizeof(*mpf), "* MP-table mpf");
 			if (mpf->physptr)
 				smp_reserve_memory(mpf);
 
arch/x86/kernel/setup.c +33 -13

94 lines not on this page · raw message

arch/x86/kernel/setup_percpu.c +0 -6
index ef6370b..35abcb8 100644
@@ -137,13 +137,7 @@ static void * __init pcpu_fc_alloc(unsigned int cpu, size_t size, size_t align)
 
 static void __init pcpu_fc_free(void *ptr, size_t size)
 {
-#ifdef CONFIG_NO_BOOTMEM
-	u64 start = __pa(ptr);
-	u64 end = start + size;
-	free_early_partial(start, end);
-#else
 	free_bootmem(__pa(ptr), size);
-#endif
 }
 
 static int __init pcpu_cpu_distance(unsigned int from, unsigned int to)
arch/x86/mm/numa_64.c +3 -2
index 8948f47..6e0f896 100644
@@ -7,6 +7,7 @@
 #include <linux/string.h>
 #include <linux/init.h>
 #include <linux/bootmem.h>
+#include <linux/lmb.h>
 #include <linux/mmzone.h>
 #include <linux/ctype.h>
 #include <linux/module.h>
@@ -174,7 +175,7 @@ static void * __init early_node_mem(int nodeid, unsigned long start,
 	if (start < (MAX_DMA32_PFN<<PAGE_SHIFT) &&
 	    end > (MAX_DMA32_PFN<<PAGE_SHIFT))
 		start = MAX_DMA32_PFN<<PAGE_SHIFT;
-	mem = find_e820_area(start, end, size, align);
+	mem = lmb_find_area_node(nodeid, start, end, size, align);
 	if (mem != -1L)
 		return __va(mem);
 
@@ -184,7 +185,7 @@ static void * __init early_node_mem(int nodeid, unsigned long start,
 		start = MAX_DMA32_PFN<<PAGE_SHIFT;
 	else
 		start = MAX_DMA_PFN<<PAGE_SHIFT;
-	mem = find_e820_area(start, end, size, align);
+	mem = lmb_find_area_node(nodeid, start, end, size, align);
 	if (mem != -1L)
 		return __va(mem);
 
kernel/Makefile +0 -1
index 34d123b..8aa4fa2 100644
@@ -11,7 +11,6 @@ obj-y     = sched.o fork.o exec_domain.o panic.o printk.o \
 	    hrtimer.o rwsem.o nsproxy.o srcu.o semaphore.o \
 	    notifier.o ksysfs.o pm_qos_params.o sched_clock.o cred.o \
 	    async.o range.o
-obj-$(CONFIG_HAVE_EARLY_RES) += early_res.o
 obj-y += groups.o
 
 ifdef CONFIG_FUNCTION_TRACER
mm/bootmem.c +1 -0
index ee31b95..dac3f56 100644
@@ -15,6 +15,7 @@
 #include <linux/module.h>
 #include <linux/kmemleak.h>
 #include <linux/range.h>
+#include <linux/lmb.h>
 
 #include <asm/bug.h>
 #include <asm/io.h>
mm/page_alloc.c +10 -26
index 8f17f1f..2023236 100644
@@ -3441,38 +3441,22 @@ int __init add_from_early_node_map(struct range *range, int az,
 void * __init __alloc_memory_core_early(int nid, u64 size, u64 align,
 					u64 goal, u64 limit)
 {
-	int i;
 	void *ptr;
 
-	/* need to go over early_node_map to find out good range for node */
-	for_each_active_range_index_in_nid(i, nid) {
-		u64 addr;
-		u64 ei_start, ei_last;
-
-		ei_last = early_node_map[i].end_pfn;
-		ei_last <<= PAGE_SHIFT;
-		ei_start = early_node_map[i].start_pfn;
-		ei_start <<= PAGE_SHIFT;
-		addr = find_early_area(ei_start, ei_last,
-					 goal, limit, size, align);
+	u64 addr;
 
-		if (addr == -1ULL)
-			continue;
+	if (limit > lmb.current_limit)
+		limit = lmb.current_limit;
 
-#if 0
-		printk(KERN_DEBUG "alloc (nid=%d %llx - %llx) (%llx - %llx) %llx %llx => %llx\n",
-				nid,
-				ei_start, ei_last, goal, limit, size,
-				align, addr);
-#endif
+	addr = find_memory_core_early(nid, size, align, goal, limit);
 
-		ptr = phys_to_virt(addr);
-		memset(ptr, 0, size);
-		reserve_early_without_check(addr, addr + size, "BOOTMEM");
-		return ptr;
-	}
+	if (addr == LMB_ERROR)
+		return NULL;
 
-	return NULL;
+	ptr = phys_to_virt(addr);
+	memset(ptr, 0, size);
+	lmb_reserve_area(addr, addr + size, "BOOTMEM");
+	return ptr;
 }
 #endif
 
mm/sparse-vmemmap.c +0 -11
index aa33fd6..29d6cbf 100644
@@ -220,18 +220,7 @@ void __init sparse_mem_maps_populate_node(struct page **map_map,
 
 	if (vmemmap_buf_start) {
 		/* need to free left buf */
-#ifdef CONFIG_NO_BOOTMEM
-		free_early(__pa(vmemmap_buf_start), __pa(vmemmap_buf_end));
-		if (vmemmap_buf_start < vmemmap_buf) {
-			char name[15];
-
-			snprintf(name, sizeof(name), "MEMMAP %d", nodeid);
-			reserve_early_without_check(__pa(vmemmap_buf_start),
-						    __pa(vmemmap_buf), name);
-		}
-#else
 		free_bootmem(__pa(vmemmap_buf), vmemmap_buf_end - vmemmap_buf);
-#endif
 		vmemmap_buf = NULL;
 		vmemmap_buf_end = NULL;
 	}
Signature · 1 line
1.6.4.2
author
#26 lore raw

PATCH 21/37 x86: Replace e820_/_early string with lmb_

In reply to Yinghai Lu

1.include linux/lmb.h directly. so later could reduce e820.h reference. 2 this patch is done by sed scripts mainly

---
 arch/x86/include/asm/efi.h      |    2 +-
 arch/x86/kernel/acpi/sleep.c    |    5 +++--
 arch/x86/kernel/apic/numaq_32.c |    3 ++-
 arch/x86/kernel/efi.c           |    5 +++--
 arch/x86/kernel/head32.c        |    4 ++--
 arch/x86/kernel/head64.c        |    4 ++--
 arch/x86/kernel/setup.c         |   25 ++++++++++++-------------
 arch/x86/kernel/trampoline.c    |    6 +++---
 arch/x86/mm/init.c              |    5 +++--
 arch/x86/mm/init_32.c           |   10 ++++++----
 arch/x86/mm/init_64.c           |    9 +++++----
 arch/x86/mm/k8topology_64.c     |    4 +++-
 arch/x86/mm/memtest.c           |    7 +++----
 arch/x86/mm/numa_32.c           |   17 +++++++++--------
 arch/x86/mm/numa_64.c           |   32 ++++++++++++++++----------------
 arch/x86/mm/srat_32.c           |    3 ++-
 arch/x86/mm/srat_64.c           |    9 +++++----
 arch/x86/xen/mmu.c              |    5 +++--
 arch/x86/xen/setup.c            |    3 ++-
 mm/bootmem.c                    |    4 ++--
 20 files changed, 87 insertions(+), 75 deletions(-)
arch/x86/include/asm/efi.h +1 -1
index 8406ed7..06703f3 100644
@@ -90,7 +90,7 @@ extern void __iomem *efi_ioremap(unsigned long addr, unsigned long size,
 #endif /* CONFIG_X86_32 */
 
 extern int add_efi_memmap;
-extern void efi_reserve_early(void);
+extern void efi_lmb_reserve_area(void);
 extern void efi_call_phys_prelog(void);
 extern void efi_call_phys_epilog(void);
 
arch/x86/kernel/acpi/sleep.c +3 -2
index 82e5086..86be7ba 100644
@@ -7,6 +7,7 @@
 
 #include <linux/acpi.h>
 #include <linux/bootmem.h>
+#include <linux/lmb.h>
 #include <linux/dmi.h>
 #include <linux/cpumask.h>
 #include <asm/segment.h>
@@ -133,7 +134,7 @@ void __init acpi_reserve_wakeup_memory(void)
 		return;
 	}
 
-	mem = find_e820_area(0, 1<<20, WAKEUP_SIZE, PAGE_SIZE);
+	mem = lmb_find_area(0, 1<<20, WAKEUP_SIZE, PAGE_SIZE);
 
 	if (mem == -1L) {
 		printk(KERN_ERR "ACPI: Cannot allocate lowmem, S3 disabled.\n");
@@ -141,7 +142,7 @@ void __init acpi_reserve_wakeup_memory(void)
 	}
 	acpi_realmode = (unsigned long) phys_to_virt(mem);
 	acpi_wakeup_address = mem;
-	reserve_early(mem, mem + WAKEUP_SIZE, "ACPI WAKEUP");
+	lmb_reserve_area(mem, mem + WAKEUP_SIZE, "ACPI WAKEUP");
 }
 
 
arch/x86/kernel/apic/numaq_32.c +2 -1
index 3e28401..c71e494 100644
@@ -26,6 +26,7 @@
 #include <linux/nodemask.h>
 #include <linux/topology.h>
 #include <linux/bootmem.h>
+#include <linux/lmb.h>
 #include <linux/threads.h>
 #include <linux/cpumask.h>
 #include <linux/kernel.h>
@@ -88,7 +89,7 @@ static inline void numaq_register_node(int node, struct sys_cfg_data *scd)
 	node_end_pfn[node] =
 		 MB_TO_PAGES(eq->hi_shrd_mem_start + eq->hi_shrd_mem_size);
 
-	e820_register_active_regions(node, node_start_pfn[node],
+	lmb_register_active_regions(node, node_start_pfn[node],
 						node_end_pfn[node]);
 
 	memory_present(node, node_start_pfn[node], node_end_pfn[node]);
arch/x86/kernel/efi.c +3 -2
index c2fa9b8..ebe7c09 100644
@@ -30,6 +30,7 @@
 #include <linux/init.h>
 #include <linux/efi.h>
 #include <linux/bootmem.h>
+#include <linux/lmb.h>
 #include <linux/spinlock.h>
 #include <linux/uaccess.h>
 #include <linux/time.h>
@@ -275,7 +276,7 @@ static void __init do_add_efi_memmap(void)
 	sanitize_e820_map(e820.map, ARRAY_SIZE(e820.map), &e820.nr_map);
 }
 
-void __init efi_reserve_early(void)
+void __init efi_lmb_reserve_area(void)
 {
 	unsigned long pmap;
 
@@ -290,7 +291,7 @@ void __init efi_reserve_early(void)
 		boot_params.efi_info.efi_memdesc_size;
 	memmap.desc_version = boot_params.efi_info.efi_memdesc_version;
 	memmap.desc_size = boot_params.efi_info.efi_memdesc_size;
-	reserve_early(pmap, pmap + memmap.nr_map * memmap.desc_size,
+	lmb_reserve_area(pmap, pmap + memmap.nr_map * memmap.desc_size,
 		      "EFI memmap");
 }
 
arch/x86/kernel/head32.c +2 -2
index ab3e366..ecd12a9 100644
@@ -42,7 +42,7 @@ void __init i386_start_kernel(void)
 	lmb_reserve_area(PAGE_SIZE, PAGE_SIZE + PAGE_SIZE, "EX TRAMPOLINE");
 #endif
 
-	reserve_early(__pa_symbol(&_text), __pa_symbol(&__bss_stop), "TEXT DATA BSS");
+	lmb_reserve_area(__pa_symbol(&_text), __pa_symbol(&__bss_stop), "TEXT DATA BSS");
 
 #ifdef CONFIG_BLK_DEV_INITRD
 	/* Reserve INITRD */
@@ -51,7 +51,7 @@ void __init i386_start_kernel(void)
 		u64 ramdisk_image = boot_params.hdr.ramdisk_image;
 		u64 ramdisk_size  = boot_params.hdr.ramdisk_size;
 		u64 ramdisk_end   = PAGE_ALIGN(ramdisk_image + ramdisk_size);
-		reserve_early(ramdisk_image, ramdisk_end, "RAMDISK");
+		lmb_reserve_area(ramdisk_image, ramdisk_end, "RAMDISK");
 	}
 #endif
 
arch/x86/kernel/head64.c +2 -2
index 89dd2de..4063134 100644
@@ -101,7 +101,7 @@ void __init x86_64_start_reservations(char *real_mode_data)
 
 	copy_bootdata(__va(real_mode_data));
 
-	reserve_early(__pa_symbol(&_text), __pa_symbol(&__bss_stop), "TEXT DATA BSS");
+	lmb_reserve_area(__pa_symbol(&_text), __pa_symbol(&__bss_stop), "TEXT DATA BSS");
 
 #ifdef CONFIG_BLK_DEV_INITRD
 	/* Reserve INITRD */
@@ -110,7 +110,7 @@ void __init x86_64_start_reservations(char *real_mode_data)
 		unsigned long ramdisk_image = boot_params.hdr.ramdisk_image;
 		unsigned long ramdisk_size  = boot_params.hdr.ramdisk_size;
 		unsigned long ramdisk_end   = PAGE_ALIGN(ramdisk_image + ramdisk_size);
-		reserve_early(ramdisk_image, ramdisk_end, "RAMDISK");
+		lmb_reserve_area(ramdisk_image, ramdisk_end, "RAMDISK");
 	}
 #endif
 
arch/x86/kernel/setup.c +12 -13
index b23da32..1a8888f 100644
@@ -302,7 +302,7 @@ static inline void init_gbpages(void)
 static void __init reserve_brk(void)
 {
 	if (_brk_end > _brk_start)
-		reserve_early(__pa(_brk_start), __pa(_brk_end), "BRK");
+		lmb_reserve_area(__pa(_brk_start), __pa(_brk_end), "BRK");
 
 	/* Mark brk area as locked down and no longer taking any
 	   new allocations */
@@ -324,7 +324,7 @@ static void __init relocate_initrd(void)
 	char *p, *q;
 
 	/* We need to move the initrd down into lowmem */
-	ramdisk_here = find_e820_area(0, end_of_lowmem, area_size,
+	ramdisk_here = lmb_find_area(0, end_of_lowmem, area_size,
 					 PAGE_SIZE);
 
 	if (ramdisk_here == -1ULL)
@@ -333,8 +333,7 @@ static void __init relocate_initrd(void)
 
 	/* Note: this includes all the lowmem currently occupied by
 	   the initrd, we rely on that fact to keep the data intact. */
-	reserve_early(ramdisk_here, ramdisk_here + area_size,
-			 "NEW RAMDISK");
+	lmb_reserve_area(ramdisk_here, ramdisk_here + area_size, "NEW RAMDISK");
 	initrd_start = ramdisk_here + PAGE_OFFSET;
 	initrd_end   = initrd_start + ramdisk_size;
 	printk(KERN_INFO "Allocated new RAMDISK: %08llx - %08llx\n",
@@ -390,7 +389,7 @@ static void __init reserve_initrd(void)
 	initrd_start = 0;
 
 	if (ramdisk_size >= (end_of_lowmem>>1)) {
-		free_early(ramdisk_image, ramdisk_end);
+		lmb_free_area(ramdisk_image, ramdisk_end);
 		printk(KERN_ERR "initrd too large to handle, "
 		       "disabling initrd\n");
 		return;
@@ -413,7 +412,7 @@ static void __init reserve_initrd(void)
 
 	relocate_initrd();
 
-	free_early(ramdisk_image, ramdisk_end);
+	lmb_free_area(ramdisk_image, ramdisk_end);
 }
 #else
 static void __init reserve_initrd(void)
@@ -469,7 +468,7 @@ static void __init e820_reserve_setup_data(void)
 	e820_print_map("reserve setup_data");
 }
 
-static void __init reserve_early_setup_data(void)
+static void __init lmb_reserve_area_setup_data(void)
 {
 	struct setup_data *data;
 	u64 pa_data;
@@ -481,7 +480,7 @@ static void __init reserve_early_setup_data(void)
 	while (pa_data) {
 		data = early_memremap(pa_data, sizeof(*data));
 		sprintf(buf, "setup data %x", data->type);
-		reserve_early(pa_data, pa_data+sizeof(*data)+data->len, buf);
+		lmb_reserve_area(pa_data, pa_data+sizeof(*data)+data->len, buf);
 		pa_data = data->next;
 		early_iounmap(data, sizeof(*data));
 	}
@@ -519,7 +518,7 @@ static void __init reserve_crashkernel(void)
 	if (crash_base <= 0) {
 		const unsigned long long alignment = 16<<20;	/* 16M */
 
-		crash_base = find_e820_area(alignment, ULONG_MAX, crash_size,
+		crash_base = lmb_find_area(alignment, ULONG_MAX, crash_size,
 				 alignment);
 		if (crash_base == -1ULL) {
 			pr_info("crashkernel reservation failed - No suitable area found.\n");
@@ -528,14 +527,14 @@ static void __init reserve_crashkernel(void)
 	} else {
 		unsigned long long start;
 
-		start = find_e820_area(crash_base, ULONG_MAX, crash_size,
+		start = lmb_find_area(crash_base, ULONG_MAX, crash_size,
 				 1<<20);
 		if (start != crash_base) {
 			pr_info("crashkernel reservation failed - memory is in use.\n");
 			return;
 		}
 	}
-	reserve_early(crash_base, crash_base + crash_size, "CRASH KERNEL");
+	lmb_reserve_area(crash_base, crash_base + crash_size, "CRASH KERNEL");
 
 	printk(KERN_INFO "Reserving %ldMB of memory at %ldMB "
 			"for crashkernel (System RAM: %ldMB)\n",
@@ -774,7 +773,7 @@ void __init setup_arch(char **cmdline_p)
 #endif
 	 4)) {
 		efi_enabled = 1;
-		efi_reserve_early();
+		efi_lmb_reserve_area();
 	}
 #endif
 
@@ -834,7 +833,7 @@ void __init setup_arch(char **cmdline_p)
 	vmi_activate();
 
 	/* after early param, so could get panic from serial */
-	reserve_early_setup_data();
+	lmb_reserve_area_setup_data();
 
 	if (acpi_mps_check()) {
 #ifdef CONFIG_X86_LOCAL_APIC
arch/x86/kernel/trampoline.c +3 -3
index c652ef6..1192dcb 100644
@@ -1,7 +1,7 @@
 #include <linux/io.h>
+#include <linux/lmb.h>
 
 #include <asm/trampoline.h>
-#include <asm/e820.h>
 
 #if defined(CONFIG_X86_64) && defined(CONFIG_ACPI_SLEEP)
 #define __trampinit
@@ -19,12 +19,12 @@ void __init reserve_trampoline_memory(void)
 	unsigned long mem;
 
 	/* Has to be in very low memory so we can execute real-mode AP code. */
-	mem = find_e820_area(0, 1<<20, TRAMPOLINE_SIZE, PAGE_SIZE);
+	mem = lmb_find_area(0, 1<<20, TRAMPOLINE_SIZE, PAGE_SIZE);
 	if (mem == -1L)
 		panic("Cannot allocate trampoline\n");
 
 	trampoline_base = __va(mem);
-	reserve_early(mem, mem + TRAMPOLINE_SIZE, "TRAMPOLINE");
+	lmb_reserve_area(mem, mem + TRAMPOLINE_SIZE, "TRAMPOLINE");
 }
 
 /*
arch/x86/mm/init.c +3 -2
index b278535..94f7cb9 100644
@@ -2,6 +2,7 @@
 #include <linux/initrd.h>
 #include <linux/ioport.h>
 #include <linux/swap.h>
+#include <linux/lmb.h>
 
 #include <asm/cacheflush.h>
 #include <asm/e820.h>
@@ -75,7 +76,7 @@ static void __init find_early_table_space(unsigned long end, int use_pse,
 #else
 	start = 0x8000;
 #endif
-	e820_table_start = find_e820_area(start, max_pfn_mapped<<PAGE_SHIFT,
+	e820_table_start = lmb_find_area(start, max_pfn_mapped<<PAGE_SHIFT,
 					tables, PAGE_SIZE);
 	if (e820_table_start == -1UL)
 		panic("Cannot find space for the kernel page tables");
@@ -299,7 +300,7 @@ unsigned long __init_refok init_memory_mapping(unsigned long start,
 	__flush_tlb_all();
 
 	if (!after_bootmem && e820_table_end > e820_table_start)
-		reserve_early(e820_table_start << PAGE_SHIFT,
+		lmb_reserve_area(e820_table_start << PAGE_SHIFT,
 				 e820_table_end << PAGE_SHIFT, "PGTABLE");
 
 	if (!after_bootmem)
arch/x86/mm/init_32.c +6 -4
index 90e0545..c01c711 100644
@@ -25,6 +25,7 @@
 #include <linux/pfn.h>
 #include <linux/poison.h>
 #include <linux/bootmem.h>
+#include <linux/lmb.h>
 #include <linux/proc_fs.h>
 #include <linux/memory_hotplug.h>
 #include <linux/initrd.h>
@@ -712,14 +713,14 @@ void __init initmem_init(unsigned long start_pfn, unsigned long end_pfn,
 	highstart_pfn = highend_pfn = max_pfn;
 	if (max_pfn > max_low_pfn)
 		highstart_pfn = max_low_pfn;
-	e820_register_active_regions(0, 0, highend_pfn);
+	lmb_register_active_regions(0, 0, highend_pfn);
 	sparse_memory_present_with_active_regions(0);
 	printk(KERN_NOTICE "%ldMB HIGHMEM available.\n",
 		pages_to_mb(highend_pfn - highstart_pfn));
 	num_physpages = highend_pfn;
 	high_memory = (void *) __va(highstart_pfn * PAGE_SIZE - 1) + 1;
 #else
-	e820_register_active_regions(0, 0, max_low_pfn);
+	lmb_register_active_regions(0, 0, max_low_pfn);
 	sparse_memory_present_with_active_regions(0);
 	num_physpages = max_low_pfn;
 	high_memory = (void *) __va(max_low_pfn * PAGE_SIZE - 1) + 1;
@@ -781,11 +782,11 @@ void __init setup_bootmem_allocator(void)
 	 * Initialize the boot-time allocator (with low memory only):
 	 */
 	bootmap_size = bootmem_bootmap_pages(max_low_pfn)<<PAGE_SHIFT;
-	bootmap = find_e820_area(0, max_pfn_mapped<<PAGE_SHIFT, bootmap_size,
+	bootmap = lmb_find_area(0, max_pfn_mapped<<PAGE_SHIFT, bootmap_size,
 				 PAGE_SIZE);
 	if (bootmap == -1L)
 		panic("Cannot find bootmem map of size %ld\n", bootmap_size);
-	reserve_early(bootmap, bootmap + bootmap_size, "BOOTMAP");
+	lmb_reserve_area(bootmap, bootmap + bootmap_size, "BOOTMAP");
 #endif
 
 	printk(KERN_INFO "  mapped low ram: 0 - %08lx\n",
@@ -1069,3 +1070,4 @@ void mark_rodata_ro(void)
 #endif
 }
 #endif
+
arch/x86/mm/init_64.c +5 -4
index 634fa08..0d2252c 100644
@@ -21,6 +21,7 @@
 #include <linux/initrd.h>
 #include <linux/pagemap.h>
 #include <linux/bootmem.h>
+#include <linux/lmb.h>
 #include <linux/proc_fs.h>
 #include <linux/pci.h>
 #include <linux/pfn.h>
@@ -577,18 +578,18 @@ void __init initmem_init(unsigned long start_pfn, unsigned long end_pfn,
 	unsigned long bootmap_size, bootmap;
 
 	bootmap_size = bootmem_bootmap_pages(end_pfn)<<PAGE_SHIFT;
-	bootmap = find_e820_area(0, end_pfn<<PAGE_SHIFT, bootmap_size,
+	bootmap = lmb_find_area(0, end_pfn<<PAGE_SHIFT, bootmap_size,
 				 PAGE_SIZE);
 	if (bootmap == -1L)
 		panic("Cannot find bootmem map of size %ld\n", bootmap_size);
-	reserve_early(bootmap, bootmap + bootmap_size, "BOOTMAP");
+	lmb_reserve_area(bootmap, bootmap + bootmap_size, "BOOTMAP");
 	/* don't touch min_low_pfn */
 	bootmap_size = init_bootmem_node(NODE_DATA(0), bootmap >> PAGE_SHIFT,
 					 0, end_pfn);
-	e820_register_active_regions(0, start_pfn, end_pfn);
+	lmb_register_active_regions(0, start_pfn, end_pfn);
 	free_bootmem_with_active_regions(0, end_pfn);
 #else
-	e820_register_active_regions(0, start_pfn, end_pfn);
+	lmb_register_active_regions(0, start_pfn, end_pfn);
 #endif
 }
 #endif
arch/x86/mm/k8topology_64.c +3 -1
index 970ed57..d7d031b 100644
@@ -11,6 +11,8 @@
 #include <linux/string.h>
 #include <linux/module.h>
 #include <linux/nodemask.h>
+#include <linux/lmb.h>
+
 #include <asm/io.h>
 #include <linux/pci_ids.h>
 #include <linux/acpi.h>
@@ -222,7 +224,7 @@ int __init k8_scan_nodes(void)
 	for_each_node_mask(i, node_possible_map) {
 		int j;
 
-		e820_register_active_regions(i,
+		lmb_register_active_regions(i,
 				nodes[i].start >> PAGE_SHIFT,
 				nodes[i].end >> PAGE_SHIFT);
 		for (j = apicid_base; j < cores + apicid_base; j++)
arch/x86/mm/memtest.c +3 -4
index 18d244f..0e4a006 100644
@@ -6,8 +6,7 @@
 #include <linux/smp.h>
 #include <linux/init.h>
 #include <linux/pfn.h>
-
-#include <asm/e820.h>
+#include <linux/lmb.h>
 
 static u64 patterns[] __initdata = {
 	0,
@@ -35,7 +34,7 @@ static void __init reserve_bad_mem(u64 pattern, u64 start_bad, u64 end_bad)
 	       (unsigned long long) pattern,
 	       (unsigned long long) start_bad,
 	       (unsigned long long) end_bad);
-	reserve_early(start_bad, end_bad, "BAD RAM");
+	lmb_reserve_area(start_bad, end_bad, "BAD RAM");
 }
 
 static void __init memtest(u64 pattern, u64 start_phys, u64 size)
@@ -74,7 +73,7 @@ static void __init do_one_pass(u64 pattern, u64 start, u64 end)
 	u64 size = 0;
 
 	while (start < end) {
-		start = find_e820_area_size(start, &size, 1);
+		start = lmb_find_area_size(start, &size, 1);
 
 		/* done ? */
 		if (start >= end)
arch/x86/mm/numa_32.c +9 -8
index 809baaa..d8d655f 100644
@@ -24,6 +24,7 @@
 
 #include <linux/mm.h>
 #include <linux/bootmem.h>
+#include <linux/lmb.h>
 #include <linux/mmzone.h>
 #include <linux/highmem.h>
 #include <linux/initrd.h>
@@ -120,7 +121,7 @@ int __init get_memcfg_numa_flat(void)
 
 	node_start_pfn[0] = 0;
 	node_end_pfn[0] = max_pfn;
-	e820_register_active_regions(0, 0, max_pfn);
+	lmb_register_active_regions(0, 0, max_pfn);
 	memory_present(0, 0, max_pfn);
 	node_remap_size[0] = node_memmap_size_bytes(0, 0, max_pfn);
 
@@ -161,14 +162,14 @@ static void __init allocate_pgdat(int nid)
 		NODE_DATA(nid) = (pg_data_t *)node_remap_start_vaddr[nid];
 	else {
 		unsigned long pgdat_phys;
-		pgdat_phys = find_e820_area(min_low_pfn<<PAGE_SHIFT,
+		pgdat_phys = lmb_find_area(min_low_pfn<<PAGE_SHIFT,
 				 max_pfn_mapped<<PAGE_SHIFT,
 				 sizeof(pg_data_t),
 				 PAGE_SIZE);
 		NODE_DATA(nid) = (pg_data_t *)(pfn_to_kaddr(pgdat_phys>>PAGE_SHIFT));
 		memset(buf, 0, sizeof(buf));
 		sprintf(buf, "NODE_DATA %d",  nid);
-		reserve_early(pgdat_phys, pgdat_phys + sizeof(pg_data_t), buf);
+		lmb_reserve_area(pgdat_phys, pgdat_phys + sizeof(pg_data_t), buf);
 	}
 	printk(KERN_DEBUG "allocate_pgdat: node %d NODE_DATA %08lx\n",
 		nid, (unsigned long)NODE_DATA(nid));
@@ -291,7 +292,7 @@ static __init unsigned long calculate_numa_remap_pages(void)
 						 PTRS_PER_PTE);
 		node_kva_target <<= PAGE_SHIFT;
 		do {
-			node_kva_final = find_e820_area(node_kva_target,
+			node_kva_final = lmb_find_area(node_kva_target,
 					((u64)node_end_pfn[nid])<<PAGE_SHIFT,
 						((u64)size)<<PAGE_SHIFT,
 						LARGE_PAGE_BYTES);
@@ -318,9 +319,9 @@ static __init unsigned long calculate_numa_remap_pages(void)
 		 *  but we could have some hole in high memory, and it will only
 		 *  check page_is_ram(pfn) && !page_is_reserved_early(pfn) to decide
 		 *  to use it as free.
-		 *  So reserve_early here, hope we don't run out of that array
+		 *  So lmb_reserve_area here, hope we don't run out of that array
 		 */
-		reserve_early(node_kva_final,
+		lmb_reserve_area(node_kva_final,
 			      node_kva_final+(((u64)size)<<PAGE_SHIFT),
 			      "KVA RAM");
 
@@ -367,7 +368,7 @@ void __init initmem_init(unsigned long start_pfn, unsigned long end_pfn,
 
 	kva_target_pfn = round_down(max_low_pfn - kva_pages, PTRS_PER_PTE);
 	do {
-		kva_start_pfn = find_e820_area(kva_target_pfn<<PAGE_SHIFT,
+		kva_start_pfn = lmb_find_area(kva_target_pfn<<PAGE_SHIFT,
 					max_low_pfn<<PAGE_SHIFT,
 					kva_pages<<PAGE_SHIFT,
 					PTRS_PER_PTE<<PAGE_SHIFT) >> PAGE_SHIFT;
@@ -382,7 +383,7 @@ void __init initmem_init(unsigned long start_pfn, unsigned long end_pfn,
 	printk(KERN_INFO "max_pfn = %lx\n", max_pfn);
 
 	/* avoid clash with initrd */
-	reserve_early(kva_start_pfn<<PAGE_SHIFT,
+	lmb_reserve_area(kva_start_pfn<<PAGE_SHIFT,
 		      (kva_start_pfn + kva_pages)<<PAGE_SHIFT,
 		     "KVA PG");
 #ifdef CONFIG_HIGHMEM
arch/x86/mm/numa_64.c +16 -16
index 6e0f896..18d2296 100644
@@ -90,7 +90,7 @@ static int __init allocate_cachealigned_memnodemap(void)
 
 	addr = 0x8000;
 	nodemap_size = roundup(sizeof(s16) * memnodemapsize, L1_CACHE_BYTES);
-	nodemap_addr = find_e820_area(addr, max_pfn<<PAGE_SHIFT,
+	nodemap_addr = lmb_find_area(addr, max_pfn<<PAGE_SHIFT,
 				      nodemap_size, L1_CACHE_BYTES);
 	if (nodemap_addr == -1UL) {
 		printk(KERN_ERR
@@ -99,7 +99,7 @@ static int __init allocate_cachealigned_memnodemap(void)
 		return -1;
 	}
 	memnodemap = phys_to_virt(nodemap_addr);
-	reserve_early(nodemap_addr, nodemap_addr + nodemap_size, "MEMNODEMAP");
+	lmb_reserve_area(nodemap_addr, nodemap_addr + nodemap_size, "MEMNODEMAP");
 
 	printk(KERN_DEBUG "NUMA: Allocated memnodemap from %lx - %lx\n",
 	       nodemap_addr, nodemap_addr + nodemap_size);
@@ -230,7 +230,7 @@ setup_node_bootmem(int nodeid, unsigned long start, unsigned long end)
 	if (node_data[nodeid] == NULL)
 		return;
 	nodedata_phys = __pa(node_data[nodeid]);
-	reserve_early(nodedata_phys, nodedata_phys + pgdat_size, "NODE_DATA");
+	lmb_reserve_area(nodedata_phys, nodedata_phys + pgdat_size, "NODE_DATA");
 	printk(KERN_INFO "  NODE_DATA [%016lx - %016lx]\n", nodedata_phys,
 		nodedata_phys + pgdat_size - 1);
 	nid = phys_to_nid(nodedata_phys);
@@ -249,7 +249,7 @@ setup_node_bootmem(int nodeid, unsigned long start, unsigned long end)
 	 * Find a place for the bootmem map
 	 * nodedata_phys could be on other nodes by alloc_bootmem,
 	 * so need to sure bootmap_start not to be small, otherwise
-	 * early_node_mem will get that with find_e820_area instead
+	 * early_node_mem will get that with lmb_find_area instead
 	 * of alloc_bootmem, that could clash with reserved range
 	 */
 	bootmap_pages = bootmem_bootmap_pages(last_pfn - start_pfn);
@@ -261,12 +261,12 @@ setup_node_bootmem(int nodeid, unsigned long start, unsigned long end)
 	bootmap = early_node_mem(nodeid, bootmap_start, end,
 				 bootmap_pages<<PAGE_SHIFT, PAGE_SIZE);
 	if (bootmap == NULL)  {
-		free_early(nodedata_phys, nodedata_phys + pgdat_size);
+		lmb_free_area(nodedata_phys, nodedata_phys + pgdat_size);
 		node_data[nodeid] = NULL;
 		return;
 	}
 	bootmap_start = __pa(bootmap);
-	reserve_early(bootmap_start, bootmap_start+(bootmap_pages<<PAGE_SHIFT),
+	lmb_reserve_area(bootmap_start, bootmap_start+(bootmap_pages<<PAGE_SHIFT),
 			"BOOTMAP");
 
 	bootmap_size = init_bootmem_node(NODE_DATA(nodeid),
@@ -420,7 +420,7 @@ static int __init split_nodes_interleave(u64 addr, u64 max_addr,
 		nr_nodes = MAX_NUMNODES;
 	}
 
-	size = (max_addr - addr - e820_hole_size(addr, max_addr)) / nr_nodes;
+	size = (max_addr - addr - lmb_hole_size(addr, max_addr)) / nr_nodes;
 	/*
 	 * Calculate the number of big nodes that can be allocated as a result
 	 * of consolidating the remainder.
@@ -456,7 +456,7 @@ static int __init split_nodes_interleave(u64 addr, u64 max_addr,
 			 * non-reserved memory is less than the per-node size.
 			 */
 			while (end - physnodes[i].start -
-				e820_hole_size(physnodes[i].start, end) < size) {
+				lmb_hole_size(physnodes[i].start, end) < size) {
 				end += FAKE_NODE_MIN_SIZE;
 				if (end > physnodes[i].end) {
 					end = physnodes[i].end;
@@ -470,7 +470,7 @@ static int __init split_nodes_interleave(u64 addr, u64 max_addr,
 			 * this one must extend to the boundary.
 			 */
 			if (end < dma32_end && dma32_end - end -
-			    e820_hole_size(end, dma32_end) < FAKE_NODE_MIN_SIZE)
+			    lmb_hole_size(end, dma32_end) < FAKE_NODE_MIN_SIZE)
 				end = dma32_end;
 
 			/*
@@ -479,7 +479,7 @@ static int __init split_nodes_interleave(u64 addr, u64 max_addr,
 			 * physical node.
 			 */
 			if (physnodes[i].end - end -
-			    e820_hole_size(end, physnodes[i].end) < size)
+			    lmb_hole_size(end, physnodes[i].end) < size)
 				end = physnodes[i].end;
 
 			/*
@@ -507,7 +507,7 @@ static u64 __init find_end_of_node(u64 start, u64 max_addr, u64 size)
 {
 	u64 end = start + size;
 
-	while (end - start - e820_hole_size(start, end) < size) {
+	while (end - start - lmb_hole_size(start, end) < size) {
 		end += FAKE_NODE_MIN_SIZE;
 		if (end > max_addr) {
 			end = max_addr;
@@ -536,7 +536,7 @@ static int __init split_nodes_size_interleave(u64 addr, u64 max_addr, u64 size)
 	 * creates a uniform distribution of node sizes across the entire
 	 * machine (but not necessarily over physical nodes).
 	 */
-	min_size = (max_addr - addr - e820_hole_size(addr, max_addr)) /
+	min_size = (max_addr - addr - lmb_hole_size(addr, max_addr)) /
 						MAX_NUMNODES;
 	min_size = max(min_size, FAKE_NODE_MIN_SIZE);
 	if ((min_size & FAKE_NODE_MIN_HASH_MASK) < min_size)
@@ -569,7 +569,7 @@ static int __init split_nodes_size_interleave(u64 addr, u64 max_addr, u64 size)
 			 * this one must extend to the boundary.
 			 */
 			if (end < dma32_end && dma32_end - end -
-			    e820_hole_size(end, dma32_end) < FAKE_NODE_MIN_SIZE)
+			    lmb_hole_size(end, dma32_end) < FAKE_NODE_MIN_SIZE)
 				end = dma32_end;
 
 			/*
@@ -578,7 +578,7 @@ static int __init split_nodes_size_interleave(u64 addr, u64 max_addr, u64 size)
 			 * physical node.
 			 */
 			if (physnodes[i].end - end -
-			    e820_hole_size(end, physnodes[i].end) < size)
+			    lmb_hole_size(end, physnodes[i].end) < size)
 				end = physnodes[i].end;
 
 			/*
@@ -642,7 +642,7 @@ static int __init numa_emulation(unsigned long start_pfn,
 	 */
 	remove_all_active_ranges();
 	for_each_node_mask(i, node_possible_map) {
-		e820_register_active_regions(i, nodes[i].start >> PAGE_SHIFT,
+		lmb_register_active_regions(i, nodes[i].start >> PAGE_SHIFT,
 						nodes[i].end >> PAGE_SHIFT);
 		setup_node_bootmem(i, nodes[i].start, nodes[i].end);
 	}
@@ -695,7 +695,7 @@ void __init initmem_init(unsigned long start_pfn, unsigned long last_pfn,
 	node_set(0, node_possible_map);
 	for (i = 0; i < nr_cpu_ids; i++)
 		numa_set_node(i, 0);
-	e820_register_active_regions(0, start_pfn, last_pfn);
+	lmb_register_active_regions(0, start_pfn, last_pfn);
 	setup_node_bootmem(0, start_pfn << PAGE_SHIFT, last_pfn << PAGE_SHIFT);
 }
 
arch/x86/mm/srat_32.c +2 -1
index 9324f13..68dd606 100644
@@ -25,6 +25,7 @@
  */
 #include <linux/mm.h>
 #include <linux/bootmem.h>
+#include <linux/lmb.h>
 #include <linux/mmzone.h>
 #include <linux/acpi.h>
 #include <linux/nodemask.h>
@@ -264,7 +265,7 @@ int __init get_memcfg_from_srat(void)
 		if (node_read_chunk(chunk->nid, chunk))
 			continue;
 
-		e820_register_active_regions(chunk->nid, chunk->start_pfn,
+		lmb_register_active_regions(chunk->nid, chunk->start_pfn,
 					     min(chunk->end_pfn, max_pfn));
 	}
 	/* for out of order entries in SRAT */
arch/x86/mm/srat_64.c +5 -4
index f9897f7..23f274c 100644
@@ -16,6 +16,7 @@
 #include <linux/module.h>
 #include <linux/topology.h>
 #include <linux/bootmem.h>
+#include <linux/lmb.h>
 #include <linux/mm.h>
 #include <asm/proto.h>
 #include <asm/numa.h>
@@ -98,7 +99,7 @@ void __init acpi_numa_slit_init(struct acpi_table_slit *slit)
 	unsigned long phys;
 
 	length = slit->header.length;
-	phys = find_e820_area(0, max_pfn_mapped<<PAGE_SHIFT, length,
+	phys = lmb_find_area(0, max_pfn_mapped<<PAGE_SHIFT, length,
 		 PAGE_SIZE);
 
 	if (phys == -1L)
@@ -106,7 +107,7 @@ void __init acpi_numa_slit_init(struct acpi_table_slit *slit)
 
 	acpi_slit = __va(phys);
 	memcpy(acpi_slit, slit, length);
-	reserve_early(phys, phys + length, "ACPI SLIT");
+	lmb_reserve_area(phys, phys + length, "ACPI SLIT");
 }
 
 /* Callback for Proximity Domain -> x2APIC mapping */
@@ -324,7 +325,7 @@ static int __init nodes_cover_memory(const struct bootnode *nodes)
 			pxmram = 0;
 	}
 
-	e820ram = max_pfn - (e820_hole_size(0, max_pfn<<PAGE_SHIFT)>>PAGE_SHIFT);
+	e820ram = max_pfn - (lmb_hole_size(0, max_pfn<<PAGE_SHIFT)>>PAGE_SHIFT);
 	/* We seem to lose 3 pages somewhere. Allow 1M of slack. */
 	if ((long)(e820ram - pxmram) >= (1<<(20 - PAGE_SHIFT))) {
 		printk(KERN_ERR
@@ -421,7 +422,7 @@ int __init acpi_scan_nodes(unsigned long start, unsigned long end)
 	}
 
 	for_each_node_mask(i, nodes_parsed)
-		e820_register_active_regions(i, nodes[i].start >> PAGE_SHIFT,
+		lmb_register_active_regions(i, nodes[i].start >> PAGE_SHIFT,
 						nodes[i].end >> PAGE_SHIFT);
 	/* for out of order entries in SRAT */
 	sort_node_map();
arch/x86/xen/mmu.c +3 -2
index 914f046..28185a8 100644
@@ -44,6 +44,7 @@
 #include <linux/bug.h>
 #include <linux/module.h>
 #include <linux/gfp.h>
+#include <linux/lmb.h>
 
 #include <asm/pgtable.h>
 #include <asm/tlbflush.h>
@@ -1735,7 +1736,7 @@ __init pgd_t *xen_setup_kernel_pagetable(pgd_t *pgd,
 	__xen_write_cr3(true, __pa(pgd));
 	xen_mc_issue(PARAVIRT_LAZY_CPU);
 
-	reserve_early(__pa(xen_start_info->pt_base),
+	lmb_reserve_area(__pa(xen_start_info->pt_base),
 		      __pa(xen_start_info->pt_base +
 			   xen_start_info->nr_pt_frames * PAGE_SIZE),
 		      "XEN PAGETABLES");
@@ -1773,7 +1774,7 @@ __init pgd_t *xen_setup_kernel_pagetable(pgd_t *pgd,
 
 	pin_pagetable_pfn(MMUEXT_PIN_L3_TABLE, PFN_DOWN(__pa(swapper_pg_dir)));
 
-	reserve_early(__pa(xen_start_info->pt_base),
+	lmb_reserve_area(__pa(xen_start_info->pt_base),
 		      __pa(xen_start_info->pt_base +
 			   xen_start_info->nr_pt_frames * PAGE_SIZE),
 		      "XEN PAGETABLES");
arch/x86/xen/setup.c +2 -1
index ad0047f..be3fcf3 100644
@@ -8,6 +8,7 @@
 #include <linux/sched.h>
 #include <linux/mm.h>
 #include <linux/pm.h>
+#include <linux/lmb.h>
 
 #include <asm/elf.h>
 #include <asm/vdso.h>
@@ -61,7 +62,7 @@ char * __init xen_memory_setup(void)
 	 *  - xen_start_info
 	 * See comment above "struct start_info" in <xen/interface/xen.h>
 	 */
-	reserve_early(__pa(xen_start_info->mfn_list),
+	lmb_reserve_area(__pa(xen_start_info->mfn_list),
 		      __pa(xen_start_info->pt_base),
 			"XEN START INFO");
 
mm/bootmem.c +2 -2
index dac3f56..2a4c8b5 100644
@@ -435,7 +435,7 @@ void __init free_bootmem_node(pg_data_t *pgdat, unsigned long physaddr,
 			      unsigned long size)
 {
 #ifdef CONFIG_NO_BOOTMEM
-	free_early(physaddr, physaddr + size);
+	lmb_free_area(physaddr, physaddr + size);
 #else
 	unsigned long start, end;
 
@@ -460,7 +460,7 @@ void __init free_bootmem_node(pg_data_t *pgdat, unsigned long physaddr,
 void __init free_bootmem(unsigned long addr, unsigned long size)
 {
 #ifdef CONFIG_NO_BOOTMEM
-	free_early(addr, addr + size);
+	lmb_free_area(addr, addr + size);
 #else
 	unsigned long start, end;
 
Signature · 1 line
1.6.4.2
author
#27 lore raw

PATCH 22/37 x86: Remove not used early_res code

In reply to Yinghai Lu

and some functions in e820.c that are not used anymore

---
 arch/x86/include/asm/e820.h |   14 -
 arch/x86/kernel/e820.c      |   42 ---
 include/linux/early_res.h   |   23 --
 kernel/early_res.c          |  584 -------------------------------------------
 4 files changed, 0 insertions(+), 663 deletions(-)
 delete mode 100644 include/linux/early_res.h
 delete mode 100644 kernel/early_res.c
arch/x86/include/asm/e820.h +0 -14
index 38adac8..6fbd8cd 100644
@@ -112,32 +112,18 @@ static inline void early_memtest(unsigned long start, unsigned long end)
 }
 #endif
 
-extern unsigned long end_user_pfn;
-
-extern u64 find_e820_area(u64 start, u64 end, u64 size, u64 align);
-extern u64 find_e820_area_size(u64 start, u64 *sizep, u64 align);
-extern u64 early_reserve_e820(u64 startt, u64 sizet, u64 align);
-
 extern unsigned long e820_end_of_ram_pfn(void);
 extern unsigned long e820_end_of_low_ram_pfn(void);
-extern void e820_register_active_regions(int nid, unsigned long start_pfn,
-					 unsigned long end_pfn);
-extern u64 e820_hole_size(u64 start, u64 end);
-
 extern u64 early_reserve_e820(u64 startt, u64 sizet, u64 align);
 
 void init_lmb_memory(void);
 void fill_lmb_memory(void);
-
 extern void finish_e820_parsing(void);
 extern void e820_reserve_resources(void);
 extern void e820_reserve_resources_late(void);
 extern void setup_memory_map(void);
 extern char *default_machine_specific_memory_setup(void);
 
-void reserve_early(u64 start, u64 end, char *name);
-void free_early(u64 start, u64 end);
-
 /*
  * Returns true iff the specified range [s,e) is completely contained inside
  * the ISA region.
arch/x86/kernel/e820.c +0 -42

54 lines not on this page · raw message

include/linux/early_res.h deleted +0 -23
deleted file mode 100644
index 29c09f5..0000000
@@ -1,23 +0,0 @@
-#ifndef _LINUX_EARLY_RES_H
-#define _LINUX_EARLY_RES_H
-#ifdef __KERNEL__
-
-extern void reserve_early(u64 start, u64 end, char *name);
-extern void reserve_early_overlap_ok(u64 start, u64 end, char *name);
-extern void free_early(u64 start, u64 end);
-void free_early_partial(u64 start, u64 end);
-extern void early_res_to_bootmem(u64 start, u64 end);
-
-void reserve_early_without_check(u64 start, u64 end, char *name);
-u64 find_early_area(u64 ei_start, u64 ei_last, u64 start, u64 end,
-			 u64 size, u64 align);
-u64 find_early_area_size(u64 ei_start, u64 ei_last, u64 start,
-			 u64 *sizep, u64 align);
-u64 find_fw_memmap_area(u64 start, u64 end, u64 size, u64 align);
-u64 get_max_mapped(void);
-#include <linux/range.h>
-int get_free_all_memory_range(struct range **rangep, int nodeid);
-
-#endif /* __KERNEL__ */
-
-#endif /* _LINUX_EARLY_RES_H */
kernel/early_res.c deleted +0 -584

584 lines not on this page · raw message

Signature · 1 line
1.6.4.2
author
#28 lore raw

PATCH 23/37 x86, lmb: Use lmb_memory_size()/lmb_free_memory_size() to get correct dma_reserve

In reply to Yinghai Lu

lmb_memory_size() will return memory size in lmb.memory.region. lmb_free_memory_size() will return free memory size in lmb.memory.region.

So We can get exact reseved size in specified range.

Set the size right after initmem_init(), because later bootmem API will get area above 16M. (except some fallback).

Later after we remove the bootmem, We could call that just before paging_init().

---
 arch/x86/include/asm/e820.h |    2 ++
 arch/x86/kernel/e820.c      |   17 +++++++++++++++++
 arch/x86/kernel/setup.c     |    1 +
 arch/x86/mm/init_64.c       |    7 -------
 4 files changed, 20 insertions(+), 7 deletions(-)
arch/x86/include/asm/e820.h +2 -0
index 6fbd8cd..f59db16 100644
@@ -118,6 +118,8 @@ extern u64 early_reserve_e820(u64 startt, u64 sizet, u64 align);
 
 void init_lmb_memory(void);
 void fill_lmb_memory(void);
+void find_lmb_dma_reserve(void);
+
 extern void finish_e820_parsing(void);
 extern void e820_reserve_resources(void);
 extern void e820_reserve_resources_late(void);
arch/x86/kernel/e820.c +17 -0
index 14b1c26..1144d20 100644
@@ -1103,3 +1103,20 @@ void __init fill_lmb_memory(void)
 	lmb_analyze();
 	lmb_dump_all();
 }
+
+void __init find_lmb_dma_reserve(void)
+{
+#ifdef CONFIG_X86_64
+	u64 free_size_pfn;
+	u64 mem_size_pfn;
+	/*
+	 * need to find out used area below MAX_DMA_PFN
+	 * need to use lmb to get free size in [0, MAX_DMA_PFN]
+	 * at first, and assume boot_mem will not take below MAX_DMA_PFN
+	 */
+	mem_size_pfn = lmb_memory_size(0, MAX_DMA_PFN << PAGE_SHIFT) >> PAGE_SHIFT;
+	free_size_pfn = lmb_free_memory_size(0, MAX_DMA_PFN << PAGE_SHIFT) >> PAGE_SHIFT;
+	set_dma_reserve(mem_size_pfn - free_size_pfn);
+#endif
+}
+
arch/x86/kernel/setup.c +1 -0
index 1a8888f..aad3e6c 100644
@@ -1001,6 +1001,7 @@ void __init setup_arch(char **cmdline_p)
 #endif
 
 	initmem_init(0, max_pfn, acpi, k8);
+	find_lmb_dma_reserve();
 #ifndef CONFIG_NO_BOOTMEM
 	lmb_to_bootmem(0, max_low_pfn<<PAGE_SHIFT);
 #endif
arch/x86/mm/init_64.c +0 -7
index 0d2252c..37c7a82 100644
@@ -53,8 +53,6 @@
 #include <asm/init.h>
 #include <linux/bootmem.h>
 
-static unsigned long dma_reserve __initdata;
-
 static int __init parse_direct_gbpages_off(char *arg)
 {
 	direct_gbpages = 0;
@@ -821,11 +819,6 @@ int __init reserve_bootmem_generic(unsigned long phys, unsigned long len,
 
 	reserve_bootmem(phys, len, flags);
 
-	if (phys+len <= MAX_DMA_PFN*PAGE_SIZE) {
-		dma_reserve += len / PAGE_SIZE;
-		set_dma_reserve(dma_reserve);
-	}
-
 	return 0;
 }
 #endif
Signature · 1 line
1.6.4.2
author
#29 lore raw

PATCH 24/37 bootmem: Add nobootmem.c to reduce the #ifdef

In reply to Yinghai Lu

Introduce nobootmem.c to hold wrapper for CONFIG_NO_BOOTMEM=y.

that will remove related #ifdef in bootmem.c

---
 mm/Makefile    |    8 +-
 mm/bootmem.c   |  151 +----------------------
 mm/nobootmem.c |  389 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 397 insertions(+), 151 deletions(-)
 create mode 100644 mm/nobootmem.c
mm/Makefile +7 -1
index 6c2a73a..08c58d5 100644
@@ -7,12 +7,18 @@ mmu-$(CONFIG_MMU)	:= fremap.o highmem.o madvise.o memory.o mincore.o \
 			   mlock.o mmap.o mprotect.o mremap.o msync.o rmap.o \
 			   vmalloc.o pagewalk.o
 
-obj-y			:= bootmem.o filemap.o mempool.o oom_kill.o fadvise.o \
+obj-y			:= filemap.o mempool.o oom_kill.o fadvise.o \
 			   maccess.o page_alloc.o page-writeback.o \
 			   readahead.o swap.o truncate.o vmscan.o shmem.o \
 			   prio_tree.o util.o mmzone.o vmstat.o backing-dev.o \
 			   page_isolation.o mm_init.o mmu_context.o \
 			   $(mmu-y)
+ifdef CONFIG_NO_BOOTMEM
+	obj-y		+= nobootmem.o
+else
+	obj-y		+= bootmem.o
+endif
+
 obj-y += init-mm.o
 
 obj-$(CONFIG_BOUNCE)	+= bounce.o
mm/bootmem.c +1 -150

335 lines not on this page · raw message

mm/nobootmem.c new file +389 -0

389 lines not on this page · raw message

Signature · 1 line
1.6.4.2
author
#30 lore raw

PATCH 25/37 mm: move contig_page_data define to bootmem.c/nobootmem.c

In reply to Yinghai Lu

We can remove #ifdef in mm/page_alloc.c

---
 mm/bootmem.c    |    7 +++++++
 mm/nobootmem.c  |    5 +++++
 mm/page_alloc.c |    9 ---------
 3 files changed, 12 insertions(+), 9 deletions(-)
mm/bootmem.c +7 -0
index 2741c34..ff55ad7 100644
@@ -23,6 +23,13 @@
 
 #include "internal.h"
 
+#ifndef CONFIG_NEED_MULTIPLE_NODES
+struct pglist_data __refdata contig_page_data = {
+ .bdata = &bootmem_node_data[0]
+ };
+EXPORT_SYMBOL(contig_page_data);
+#endif
+
 unsigned long max_low_pfn;
 unsigned long min_low_pfn;
 unsigned long max_pfn;
mm/nobootmem.c +5 -0
index 283673e..abaec96 100644
@@ -23,6 +23,11 @@
 
 #include "internal.h"
 
+#ifndef CONFIG_NEED_MULTIPLE_NODES
+struct pglist_data __refdata contig_page_data;
+EXPORT_SYMBOL(contig_page_data);
+#endif
+
 unsigned long max_low_pfn;
 unsigned long min_low_pfn;
 unsigned long max_pfn;
mm/page_alloc.c +0 -9
index 2023236..704b26f 100644
@@ -4496,15 +4496,6 @@ void __init set_dma_reserve(unsigned long new_dma_reserve)
 	dma_reserve = new_dma_reserve;
 }
 
-#ifndef CONFIG_NEED_MULTIPLE_NODES
-struct pglist_data __refdata contig_page_data = {
-#ifndef CONFIG_NO_BOOTMEM
- .bdata = &bootmem_node_data[0]
-#endif
- };
-EXPORT_SYMBOL(contig_page_data);
-#endif
-
 void __init free_area_init(unsigned long *zones_size)
 {
 	free_area_init_node(0, zones_size,
Signature · 1 line
1.6.4.2
author
#31 lore raw

PATCH 26/37 lmb: Move __alloc_memory_core_early() to nobootmem.c

In reply to Yinghai Lu

We can remove #ifdef in mm/page_alloc.c

and change that function to static

---
 include/linux/mm.h |    2 --
 mm/nobootmem.c     |   21 +++++++++++++++++++++
 mm/page_alloc.c    |   24 ------------------------
 3 files changed, 21 insertions(+), 26 deletions(-)
include/linux/mm.h +0 -2
index 7774e1d..2a14361 100644
@@ -1161,8 +1161,6 @@ int add_from_early_node_map(struct range *range, int az,
 				   int nr_range, int nid);
 u64 __init find_memory_core_early(int nid, u64 size, u64 align,
 					u64 goal, u64 limit);
-void *__alloc_memory_core_early(int nodeid, u64 size, u64 align,
-				 u64 goal, u64 limit);
 typedef int (*work_fn_t)(unsigned long, unsigned long, void *);
 extern void work_with_active_regions(int nid, work_fn_t work_fn, void *data);
 extern void sparse_memory_present_with_active_regions(int nid);
mm/nobootmem.c +21 -0
index abaec96..e3cbde7 100644
@@ -40,6 +40,27 @@ unsigned long max_pfn;
 unsigned long saved_max_pfn;
 #endif
 
+static void * __init __alloc_memory_core_early(int nid, u64 size, u64 align,
+					u64 goal, u64 limit)
+{
+	void *ptr;
+
+	u64 addr;
+
+	if (limit > lmb.current_limit)
+		limit = lmb.current_limit;
+
+	addr = find_memory_core_early(nid, size, align, goal, limit);
+
+	if (addr == LMB_ERROR)
+		return NULL;
+
+	ptr = phys_to_virt(addr);
+	memset(ptr, 0, size);
+	lmb_reserve_area(addr, addr + size, "BOOTMEM");
+	return ptr;
+}
+
 /*
  * free_bootmem_late - free bootmem pages directly to page allocator
  * @addr: starting address of the range
mm/page_alloc.c +0 -24
index 704b26f..7a07e12 100644
@@ -3437,30 +3437,6 @@ int __init add_from_early_node_map(struct range *range, int az,
 	return nr_range;
 }
 
-#ifdef CONFIG_NO_BOOTMEM
-void * __init __alloc_memory_core_early(int nid, u64 size, u64 align,
-					u64 goal, u64 limit)
-{
-	void *ptr;
-
-	u64 addr;
-
-	if (limit > lmb.current_limit)
-		limit = lmb.current_limit;
-
-	addr = find_memory_core_early(nid, size, align, goal, limit);
-
-	if (addr == LMB_ERROR)
-		return NULL;
-
-	ptr = phys_to_virt(addr);
-	memset(ptr, 0, size);
-	lmb_reserve_area(addr, addr + size, "BOOTMEM");
-	return ptr;
-}
-#endif
-
-
 void __init work_with_active_regions(int nid, work_fn_t work_fn, void *data)
 {
 	int i;
Signature · 1 line
1.6.4.2
author
#32 lore raw

PATCH 27/37 x86: Have nobootmem version setup_bootmem_allocator()

In reply to Yinghai Lu

We can reduce #ifdef number from 3 to one in init_32.c

---
 arch/x86/mm/init_32.c |   15 ++++++++++-----
 1 files changed, 10 insertions(+), 5 deletions(-)
arch/x86/mm/init_32.c +10 -5
index c01c711..dfdd035 100644
@@ -771,11 +771,9 @@ static unsigned long __init setup_node_bootmem(int nodeid,
 
 	return bootmap + bootmap_size;
 }
-#endif
 
 void __init setup_bootmem_allocator(void)
 {
-#ifndef CONFIG_NO_BOOTMEM
 	int nodeid;
 	unsigned long bootmap_size, bootmap;
 	/*
@@ -787,13 +785,11 @@ void __init setup_bootmem_allocator(void)
 	if (bootmap == -1L)
 		panic("Cannot find bootmem map of size %ld\n", bootmap_size);
 	lmb_reserve_area(bootmap, bootmap + bootmap_size, "BOOTMAP");
-#endif
 
 	printk(KERN_INFO "  mapped low ram: 0 - %08lx\n",
 		 max_pfn_mapped<<PAGE_SHIFT);
 	printk(KERN_INFO "  low ram: 0 - %08lx\n", max_low_pfn<<PAGE_SHIFT);
 
-#ifndef CONFIG_NO_BOOTMEM
 	for_each_online_node(nodeid) {
 		 unsigned long start_pfn, end_pfn;
 
@@ -811,10 +807,19 @@ void __init setup_bootmem_allocator(void)
 		bootmap = setup_node_bootmem(nodeid, start_pfn, end_pfn,
 						 bootmap);
 	}
-#endif
 
 	after_bootmem = 1;
 }
+#else
+void __init setup_bootmem_allocator(void)
+{
+	printk(KERN_INFO "  mapped low ram: 0 - %08lx\n",
+		 max_pfn_mapped<<PAGE_SHIFT);
+	printk(KERN_INFO "  low ram: 0 - %08lx\n", max_low_pfn<<PAGE_SHIFT);
+
+	after_bootmem = 1;
+}
+#endif
 
 /*
  * paging_init() sets up the page tables - note that the first 8MB are
Signature · 1 line
1.6.4.2
author
#33 lore raw

PATCH 28/37 x86: Put 64 bit numa node memmap above 16M

In reply to Yinghai Lu

Do not use 0x8000 hard code value anymore.

---
 arch/x86/mm/numa_64.c |    2 +-
 arch/x86/mm/srat_64.c |    4 ++--
 2 files changed, 3 insertions(+), 3 deletions(-)
arch/x86/mm/numa_64.c +1 -1
index 18d2296..b8438ac 100644
@@ -88,7 +88,7 @@ static int __init allocate_cachealigned_memnodemap(void)
 	if (memnodemapsize <= ARRAY_SIZE(memnode.embedded_map))
 		return 0;
 
-	addr = 0x8000;
+	addr = __pa(MAX_DMA_ADDRESS);
 	nodemap_size = roundup(sizeof(s16) * memnodemapsize, L1_CACHE_BYTES);
 	nodemap_addr = lmb_find_area(addr, max_pfn<<PAGE_SHIFT,
 				      nodemap_size, L1_CACHE_BYTES);
arch/x86/mm/srat_64.c +2 -2
index 23f274c..c206b08 100644
@@ -99,8 +99,8 @@ void __init acpi_numa_slit_init(struct acpi_table_slit *slit)
 	unsigned long phys;
 
 	length = slit->header.length;
-	phys = lmb_find_area(0, max_pfn_mapped<<PAGE_SHIFT, length,
-		 PAGE_SIZE);
+	phys = lmb_find_area(__pa(MAX_DMA_ADDRESS), max_pfn_mapped<<PAGE_SHIFT,
+				 length, PAGE_SIZE);
 
 	if (phys == -1L)
 		panic(" Can not save slit!\n");
Signature · 1 line
1.6.4.2
author
#34 lore raw

PATCH 29/37 swiotlb: Use page alignment for early buffer allocation

In reply to Yinghai Lu

for 2.6.34

We could call free_bootmem_late() if swiotlb is not used, and it will shrink to page alignement.

So alloc them with page alignment at first, to avoid lose two pages

before patch:

[    0.000000]     lmb_reserve_area: [00d3600000, 00d7600000]   swiotlb buffer
[    0.000000]     lmb_reserve_area: [00d7e7ef40, 00d7e9ef40]     swiotlb list
[    0.000000]     lmb_reserve_area: [00d7e3ef40, 00d7e7ef40]  swiotlb orig_ad
[    0.000000]     lmb_reserve_area: [000008a000, 0000092000]  swiotlb overflo

after patch will get

[    0.000000]     lmb_reserve_area: [00d3600000, 00d7600000]   swiotlb buffer
[    0.000000]     lmb_reserve_area: [00d7e7e000, 00d7e9e000]     swiotlb list
[    0.000000]     lmb_reserve_area: [00d7e3e000, 00d7e7e000]  swiotlb orig_ad
[    0.000000]     lmb_reserve_area: [000008a000, 0000092000]  swiotlb overflo
Cc FUJITA Tomonori <[email protected]>
Cc Becky Bruce <[email protected]>
---
 lib/swiotlb.c |   16 ++++++++--------
 1 files changed, 8 insertions(+), 8 deletions(-)
lib/swiotlb.c +8 -8
index 5fddf72..1bd4258 100644
@@ -159,7 +159,7 @@ swiotlb_init_with_default_size(size_t default_size, int verbose)
 	/*
 	 * Get IO TLB memory from the low pages
 	 */
-	io_tlb_start = alloc_bootmem_low_pages(bytes);
+	io_tlb_start = alloc_bootmem_low_pages(PAGE_ALIGN(bytes));
 	if (!io_tlb_start)
 		panic("Cannot allocate SWIOTLB buffer");
 	io_tlb_end = io_tlb_start + bytes;
@@ -169,16 +169,16 @@ swiotlb_init_with_default_size(size_t default_size, int verbose)
 	 * to find contiguous free memory regions of size up to IO_TLB_SEGSIZE
 	 * between io_tlb_start and io_tlb_end.
 	 */
-	io_tlb_list = alloc_bootmem(io_tlb_nslabs * sizeof(int));
+	io_tlb_list = alloc_bootmem_pages(PAGE_ALIGN(io_tlb_nslabs * sizeof(int)));
 	for (i = 0; i < io_tlb_nslabs; i++)
  		io_tlb_list[i] = IO_TLB_SEGSIZE - OFFSET(i, IO_TLB_SEGSIZE);
 	io_tlb_index = 0;
-	io_tlb_orig_addr = alloc_bootmem(io_tlb_nslabs * sizeof(phys_addr_t));
+	io_tlb_orig_addr = alloc_bootmem_pages(PAGE_ALIGN(io_tlb_nslabs * sizeof(phys_addr_t)));
 
 	/*
 	 * Get the overflow emergency buffer
 	 */
-	io_tlb_overflow_buffer = alloc_bootmem_low(io_tlb_overflow);
+	io_tlb_overflow_buffer = alloc_bootmem_low_pages(PAGE_ALIGN(io_tlb_overflow));
 	if (!io_tlb_overflow_buffer)
 		panic("Cannot allocate SWIOTLB overflow buffer!\n");
 	if (verbose)
@@ -304,13 +304,13 @@ void __init swiotlb_free(void)
 			   get_order(io_tlb_nslabs << IO_TLB_SHIFT));
 	} else {
 		free_bootmem_late(__pa(io_tlb_overflow_buffer),
-				  io_tlb_overflow);
+				  PAGE_ALIGN(io_tlb_overflow));
 		free_bootmem_late(__pa(io_tlb_orig_addr),
-				  io_tlb_nslabs * sizeof(phys_addr_t));
+				  PAGE_ALIGN(io_tlb_nslabs * sizeof(phys_addr_t)));
 		free_bootmem_late(__pa(io_tlb_list),
-				  io_tlb_nslabs * sizeof(int));
+				  PAGE_ALIGN(io_tlb_nslabs * sizeof(int)));
 		free_bootmem_late(__pa(io_tlb_start),
-				  io_tlb_nslabs << IO_TLB_SHIFT);
+				  PAGE_ALIGN(io_tlb_nslabs << IO_TLB_SHIFT));
 	}
 }
 
Signature · 1 line
1.6.4.2
author
#35 lore raw

PATCH 30/37 x86: Add sanitize_e820_map()

In reply to Yinghai Lu

for 2.6.34

So We don't need to carry e820.map with it.

---
 arch/x86/include/asm/e820.h |    3 +--
 arch/x86/kernel/e820.c      |   17 +++++++++++------
 arch/x86/kernel/efi.c       |    2 +-
 arch/x86/kernel/setup.c     |    8 ++++----
 arch/x86/xen/setup.c        |    4 +---
 5 files changed, 18 insertions(+), 16 deletions(-)
arch/x86/include/asm/e820.h +1 -2
index f59db16..25962e1 100644
@@ -82,8 +82,7 @@ extern int e820_any_mapped(u64 start, u64 end, unsigned type);
 extern int e820_all_mapped(u64 start, u64 end, unsigned type);
 extern void e820_add_region(u64 start, u64 size, int type);
 extern void e820_print_map(char *who);
-extern int
-sanitize_e820_map(struct e820entry *biosmap, int max_nr_map, u32 *pnr_map);
+int sanitize_e820_map(void);
 extern u64 e820_update_range(u64 start, u64 size, unsigned old_type,
 			       unsigned new_type);
 extern u64 e820_remove_range(u64 start, u64 size, unsigned old_type,
arch/x86/kernel/e820.c +11 -6
index 1144d20..3c4ddaa 100644
@@ -225,7 +225,7 @@ void __init e820_print_map(char *who)
  *	   ______________________4_
  */
 
-int __init sanitize_e820_map(struct e820entry *biosmap, int max_nr_map,
+static int __init __sanitize_e820_map(struct e820entry *biosmap, int max_nr_map,
 			     u32 *pnr_map)
 {
 	struct change_member {
@@ -384,6 +384,11 @@ int __init sanitize_e820_map(struct e820entry *biosmap, int max_nr_map,
 	return 0;
 }
 
+int __init sanitize_e820_map(void)
+{
+	return __sanitize_e820_map(e820.map, ARRAY_SIZE(e820.map), &e820.nr_map);
+}
+
 static int __init __append_e820_map(struct e820entry *biosmap, int nr_map)
 {
 	while (nr_map) {
@@ -572,7 +577,7 @@ void __init update_e820(void)
 	u32 nr_map;
 
 	nr_map = e820.nr_map;
-	if (sanitize_e820_map(e820.map, ARRAY_SIZE(e820.map), &nr_map))
+	if (__sanitize_e820_map(e820.map, ARRAY_SIZE(e820.map), &nr_map))
 		return;
 	e820.nr_map = nr_map;
 	printk(KERN_INFO "modified physical RAM map:\n");
@@ -583,7 +588,7 @@ static void __init update_e820_saved(void)
 	u32 nr_map;
 
 	nr_map = e820_saved.nr_map;
-	if (sanitize_e820_map(e820_saved.map, ARRAY_SIZE(e820_saved.map), &nr_map))
+	if (__sanitize_e820_map(e820_saved.map, ARRAY_SIZE(e820_saved.map), &nr_map))
 		return;
 	e820_saved.nr_map = nr_map;
 }
@@ -678,7 +683,7 @@ void __init parse_e820_ext(struct setup_data *sdata, unsigned long pa_data)
 		sdata = early_ioremap(pa_data, map_len);
 	extmap = (struct e820entry *)(sdata->data);
 	__append_e820_map(extmap, entries);
-	sanitize_e820_map(e820.map, ARRAY_SIZE(e820.map), &e820.nr_map);
+	sanitize_e820_map();
 	if (map_len > PAGE_SIZE)
 		early_iounmap(sdata, map_len);
 	printk(KERN_INFO "extended physical RAM map:\n");
@@ -910,7 +915,7 @@ void __init finish_e820_parsing(void)
 	if (userdef) {
 		u32 nr = e820.nr_map;
 
-		if (sanitize_e820_map(e820.map, ARRAY_SIZE(e820.map), &nr) < 0)
+		if (__sanitize_e820_map(e820.map, ARRAY_SIZE(e820.map), &nr) < 0)
 			early_panic("Invalid user supplied memory map");
 		e820.nr_map = nr;
 
@@ -1040,7 +1045,7 @@ char *__init default_machine_specific_memory_setup(void)
 	 * the next section from 1mb->appropriate_mem_k
 	 */
 	new_nr = boot_params.e820_entries;
-	sanitize_e820_map(boot_params.e820_map,
+	__sanitize_e820_map(boot_params.e820_map,
 			ARRAY_SIZE(boot_params.e820_map),
 			&new_nr);
 	boot_params.e820_entries = new_nr;
arch/x86/kernel/efi.c +1 -1
index ebe7c09..bb31919 100644
@@ -273,7 +273,7 @@ static void __init do_add_efi_memmap(void)
 		}
 		e820_add_region(start, size, e820_type);
 	}
-	sanitize_e820_map(e820.map, ARRAY_SIZE(e820.map), &e820.nr_map);
+	sanitize_e820_map();
 }
 
 void __init efi_lmb_reserve_area(void)
arch/x86/kernel/setup.c +4 -4
index aad3e6c..33ff7f4 100644
@@ -462,7 +462,7 @@ static void __init e820_reserve_setup_data(void)
 	if (!found)
 		return;
 
-	sanitize_e820_map(e820.map, ARRAY_SIZE(e820.map), &e820.nr_map);
+	sanitize_e820_map();
 	memcpy(&e820_saved, &e820, sizeof(struct e820map));
 	printk(KERN_INFO "extended physical RAM map:\n");
 	e820_print_map("reserve setup_data");
@@ -625,7 +625,7 @@ static int __init dmi_low_memory_corruption(const struct dmi_system_id *d)
 		d->ident);
 
 	e820_update_range(0, 0x10000, E820_RAM, E820_RESERVED);
-	sanitize_e820_map(e820.map, ARRAY_SIZE(e820.map), &e820.nr_map);
+	sanitize_e820_map();
 
 	return 0;
 }
@@ -694,7 +694,7 @@ static void __init trim_bios_range(void)
 	 * take them out.
 	 */
 	e820_remove_range(BIOS_BEGIN, BIOS_END - BIOS_BEGIN, E820_RAM, 1);
-	sanitize_e820_map(e820.map, ARRAY_SIZE(e820.map), &e820.nr_map);
+	sanitize_e820_map();
 }
 
 static u64 __init get_max_mapped(void)
@@ -874,7 +874,7 @@ void __init setup_arch(char **cmdline_p)
 	if (ppro_with_ram_bug()) {
 		e820_update_range(0x70000000ULL, 0x40000ULL, E820_RAM,
 				  E820_RESERVED);
-		sanitize_e820_map(e820.map, ARRAY_SIZE(e820.map), &e820.nr_map);
+		sanitize_e820_map();
 		printk(KERN_INFO "fixed physical RAM map:\n");
 		e820_print_map("bad_ppro");
 	}
arch/x86/xen/setup.c +1 -3
index be3fcf3..d2954eb 100644
@@ -44,8 +44,6 @@ char * __init xen_memory_setup(void)
 
 	max_pfn = min(MAX_DOMAIN_PAGES, max_pfn);
 
-	e820.nr_map = 0;
-
 	e820_add_region(0, PFN_PHYS((u64)max_pfn), E820_RAM);
 
 	/*
@@ -66,7 +64,7 @@ char * __init xen_memory_setup(void)
 		      __pa(xen_start_info->pt_base),
 			"XEN START INFO");
 
-	sanitize_e820_map(e820.map, ARRAY_SIZE(e820.map), &e820.nr_map);
+	sanitize_e820_map();
 
 	return "Xen";
 }
Signature · 1 line
1.6.4.2
author
#36 lore raw

PATCH 31/37 x86: Change e820_saved to __initdata

In reply to Yinghai Lu

for 2.6.34

Add save_e820_map() and change e820_saved to static also make it to be __initdata to get some bytes memory back.

---
 arch/x86/include/asm/e820.h |    2 +-
 arch/x86/kernel/e820.c      |    9 +++++++--
 arch/x86/kernel/setup.c     |    2 +-
 3 files changed, 9 insertions(+), 4 deletions(-)
arch/x86/include/asm/e820.h +1 -1
index 25962e1..334281f 100644
@@ -75,7 +75,6 @@ struct e820map {
 #ifdef __KERNEL__
 /* see comment in arch/x86/kernel/e820.c */
 extern struct e820map e820;
-extern struct e820map e820_saved;
 
 extern unsigned long pci_mem_start;
 extern int e820_any_mapped(u64 start, u64 end, unsigned type);
@@ -83,6 +82,7 @@ extern int e820_all_mapped(u64 start, u64 end, unsigned type);
 extern void e820_add_region(u64 start, u64 size, int type);
 extern void e820_print_map(char *who);
 int sanitize_e820_map(void);
+void save_e820_map(void);
 extern u64 e820_update_range(u64 start, u64 size, unsigned old_type,
 			       unsigned new_type);
 extern u64 e820_remove_range(u64 start, u64 size, unsigned old_type,
arch/x86/kernel/e820.c +7 -2
index 3c4ddaa..bae44dd 100644
@@ -36,7 +36,7 @@
  * next kernel with full memory.
  */
 struct e820map e820;
-struct e820map e820_saved;
+static struct e820map __initdata e820_saved;
 
 /* For PCI or other memory-mapped resources */
 unsigned long pci_mem_start = 0xaeedbabe;
@@ -1072,12 +1072,17 @@ char *__init default_machine_specific_memory_setup(void)
 	return who;
 }
 
+void __init save_e820_map(void)
+{
+	memcpy(&e820_saved, &e820, sizeof(struct e820map));
+}
+
 void __init setup_memory_map(void)
 {
 	char *who;
 
 	who = x86_init.resources.memory_setup();
-	memcpy(&e820_saved, &e820, sizeof(struct e820map));
+	save_e820_map();
 	printk(KERN_INFO "BIOS-provided physical RAM map:\n");
 	e820_print_map(who);
 }
arch/x86/kernel/setup.c +1 -1
index 33ff7f4..d165b2d 100644
@@ -463,7 +463,7 @@ static void __init e820_reserve_setup_data(void)
 		return;
 
 	sanitize_e820_map();
-	memcpy(&e820_saved, &e820, sizeof(struct e820map));
+	save_e820_map();
 	printk(KERN_INFO "extended physical RAM map:\n");
 	e820_print_map("reserve setup_data");
 }
Signature · 1 line
1.6.4.2
author
#37 lore raw

PATCH 32/37 x86: Align e820 ram range to page

In reply to Yinghai Lu

for 2.6.34

To workaround wrong BIOS memory map.

---
 arch/x86/kernel/e820.c |   44 ++++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 44 insertions(+), 0 deletions(-)
arch/x86/kernel/e820.c +44 -0
index bae44dd..b2753e7 100644
@@ -910,6 +910,47 @@ static int __init parse_memmap_opt(char *p)
 }
 early_param("memmap", parse_memmap_opt);
 
+static void __init e820_align_ram_page(void)
+{
+	int i;
+	bool changed = false;;
+
+	for (i = 0; i < e820.nr_map; i++) {
+		struct e820entry *entry = &e820.map[i];
+		u64 start, end;
+		u64 start_aligned, end_aligned;
+
+		if (entry->type != E820_RAM)
+			continue;
+
+		start = entry->addr;
+		end = start + entry->size;
+
+		start_aligned = round_up(start, PAGE_SIZE);
+		end_aligned = round_down(end, PAGE_SIZE);
+
+		if (end_aligned <= start_aligned) {
+			e820_update_range(start, end - start, E820_RAM, E820_RESERVED);
+			changed = true;
+			continue;
+		}
+		if (start < start_aligned) {
+			e820_update_range(start, start_aligned - start, E820_RAM, E820_RESERVED);
+			changed = true;
+		}
+		if (end_aligned < end) {
+			e820_update_range(end_aligned, end - end_aligned, E820_RAM, E820_RESERVED);
+			changed = true;
+		}
+	}
+
+	if (changed) {
+		sanitize_e820_map();
+		printk(KERN_INFO "aligned physical RAM map:\n");
+		e820_print_map("aligned");
+	}
+}
+
 void __init finish_e820_parsing(void)
 {
 	if (userdef) {
@@ -922,6 +963,9 @@ void __init finish_e820_parsing(void)
 		printk(KERN_INFO "user-defined physical RAM map:\n");
 		e820_print_map("user");
 	}
+
+	/* In case, We have RAM entres that are not PAGE aligned */
+	e820_align_ram_page();
 }
 
 static inline const char *e820_type_to_string(int e820_type)
Signature · 1 line
1.6.4.2
author
#38 lore raw

PATCH 33/37 x86: Use wake_system_ram_range() instead of e820_any_mapped() in agp path

In reply to Yinghai Lu

Move apterture_valid back to .c

and early path still use e820_any_mapped()

So later we can make e820_any_mapped() to _init

---
 arch/x86/include/asm/gart.h   |   22 ----------------------
 arch/x86/kernel/aperture_64.c |   22 ++++++++++++++++++++++
 drivers/char/agp/amd64-agp.c  |   39 ++++++++++++++++++++++++++++++++++++++-
 3 files changed, 60 insertions(+), 23 deletions(-)
arch/x86/include/asm/gart.h +0 -22
index 4ac5b0f..2b63a91 100644
@@ -74,26 +74,4 @@ static inline void enable_gart_translation(struct pci_dev *dev, u64 addr)
         pci_write_config_dword(dev, AMD64_GARTAPERTURECTL, ctl);
 }
 
-static inline int aperture_valid(u64 aper_base, u32 aper_size, u32 min_size)
-{
-	if (!aper_base)
-		return 0;
-
-	if (aper_base + aper_size > 0x100000000ULL) {
-		printk(KERN_INFO "Aperture beyond 4GB. Ignoring.\n");
-		return 0;
-	}
-	if (e820_any_mapped(aper_base, aper_base + aper_size, E820_RAM)) {
-		printk(KERN_INFO "Aperture pointing to e820 RAM. Ignoring.\n");
-		return 0;
-	}
-	if (aper_size < min_size) {
-		printk(KERN_INFO "Aperture too small (%d MB) than (%d MB)\n",
-				 aper_size>>20, min_size>>20);
-		return 0;
-	}
-
-	return 1;
-}
-
 #endif /* _ASM_X86_GART_H */
arch/x86/kernel/aperture_64.c +22 -0
index b5d8b0b..4755b5a 100644
@@ -145,6 +145,28 @@ static u32 __init find_cap(int bus, int slot, int func, int cap)
 	return 0;
 }
 
+static int __init aperture_valid(u64 aper_base, u32 aper_size, u32 min_size)
+{
+	if (!aper_base)
+		return 0;
+
+	if (aper_base + aper_size > 0x100000000ULL) {
+		printk(KERN_INFO "Aperture beyond 4GB. Ignoring.\n");
+		return 0;
+	}
+	if (e820_any_mapped(aper_base, aper_base + aper_size, E820_RAM)) {
+		printk(KERN_INFO "Aperture pointing to e820 RAM. Ignoring.\n");
+		return 0;
+	}
+	if (aper_size < min_size) {
+		printk(KERN_INFO "Aperture too small (%d MB) than (%d MB)\n",
+				 aper_size>>20, min_size>>20);
+		return 0;
+	}
+
+	return 1;
+}
+
 /* Read a standard AGPv3 bridge header */
 static u32 __init read_agp(int bus, int slot, int func, int cap, u32 *order)
 {
drivers/char/agp/amd64-agp.c +38 -1
index fd50ead..85cabd0 100644
@@ -14,7 +14,6 @@
 #include <linux/agp_backend.h>
 #include <linux/mmzone.h>
 #include <asm/page.h>		/* PAGE_SIZE */
-#include <asm/e820.h>
 #include <asm/k8.h>
 #include <asm/gart.h>
 #include "agp.h"
@@ -231,6 +230,44 @@ static const struct agp_bridge_driver amd_8151_driver = {
 	.agp_type_to_mask_type  = agp_generic_type_to_mask_type,
 };
 
+static int __devinit
+__is_ram(unsigned long pfn, unsigned long nr_pages, void *arg)
+{
+	return 1;
+}
+
+static int __devinit any_ram_in_range(u64 base, u64 size)
+{
+	unsigned long pfn, nr_pages;
+
+	pfn = base >> PAGE_SHIFT;
+	nr_pages = size >> PAGE_SHIFT;
+
+	return walk_system_ram_range(pfn, nr_pages, NULL, __is_ram) == 1;
+}
+
+static int __devinit aperture_valid(u64 aper_base, u32 aper_size, u32 min_size)
+{
+	if (!aper_base)
+		return 0;
+
+	if (aper_base + aper_size > 0x100000000ULL) {
+		printk(KERN_INFO "Aperture beyond 4GB. Ignoring.\n");
+		return 0;
+	}
+	if (any_ram_in_range(aper_base, aper_size)) {
+		printk(KERN_INFO "Aperture pointing to E820 RAM. Ignoring.\n");
+		return 0;
+	}
+	if (aper_size < min_size) {
+		printk(KERN_INFO "Aperture too small (%d MB) than (%d MB)\n",
+				 aper_size>>20, min_size>>20);
+		return 0;
+	}
+
+	return 1;
+}
+
 /* Some basic sanity checks for the aperture. */
 static int __devinit agp_aperture_valid(u64 aper, u32 size)
 {
Signature · 1 line
1.6.4.2
author
#39 lore raw

PATCH 34/37 x86: Add get_centaur_ram_top()

In reply to Yinghai Lu

So we can avoid to access e820.map[] directly.

later we could move e820 to static and _initdata

---
 arch/x86/include/asm/e820.h   |    9 ++++++
 arch/x86/kernel/cpu/centaur.c |   53 +-------------------------------------
 arch/x86/kernel/e820.c        |   56 +++++++++++++++++++++++++++++++++++++++++
 arch/x86/kernel/setup.c       |    2 +
 4 files changed, 69 insertions(+), 51 deletions(-)
arch/x86/include/asm/e820.h +9 -0
index 334281f..cd7de51 100644
@@ -76,6 +76,15 @@ struct e820map {
 /* see comment in arch/x86/kernel/e820.c */
 extern struct e820map e820;
 
+#if defined(CONFIG_X86_OOSTORE) && defined(CONFIG_CPU_SUP_CENTAUR)
+extern int centaur_ram_top;
+void get_centaur_ram_top(void);
+#else
+static inline void get_centaur_ram_top(void)
+{
+}
+#endif
+
 extern unsigned long pci_mem_start;
 extern int e820_any_mapped(u64 start, u64 end, unsigned type);
 extern int e820_all_mapped(u64 start, u64 end, unsigned type);
arch/x86/kernel/cpu/centaur.c +2 -51

65 lines not on this page · raw message

arch/x86/kernel/e820.c +56 -0

62 lines not on this page · raw message

arch/x86/kernel/setup.c +2 -0
index d165b2d..222515c 100644
@@ -893,6 +893,8 @@ void __init setup_arch(char **cmdline_p)
 	if (mtrr_trim_uncached_memory(max_pfn))
 		max_pfn = e820_end_of_ram_pfn();
 
+	get_centaur_ram_top();
+
 #ifdef CONFIG_X86_32
 	/* max_low_pfn get updated here */
 	find_low_pfn_range();
Signature · 1 line
1.6.4.2
author
#40 lore raw

PATCH 35/37 x86: Change e820_any_mapped() to __init

In reply to Yinghai Lu

We don't need to expose e820_any_mapped() anymore

---
 arch/x86/kernel/e820.c |    6 +++---
 1 files changed, 3 insertions(+), 3 deletions(-)
arch/x86/kernel/e820.c +3 -3
index eb556d0..c2e18f9 100644
@@ -47,9 +47,10 @@ EXPORT_SYMBOL(pci_mem_start);
 /*
  * This function checks if any part of the range <start,end> is mapped
  * with type.
+ * phys_pud_init() is using it and is _meminit, but we have !after_bootmem
+ * so could use refok here
  */
-int
-e820_any_mapped(u64 start, u64 end, unsigned type)
+int __init_refok e820_any_mapped(u64 start, u64 end, unsigned type)
 {
 	int i;
 
@@ -64,7 +65,6 @@ e820_any_mapped(u64 start, u64 end, unsigned type)
 	}
 	return 0;
 }
-EXPORT_SYMBOL_GPL(e820_any_mapped);
 
 /*
  * This function checks if the entire range <start,end> is mapped with type.
Signature · 1 line
1.6.4.2
author
#41 lore raw

PATCH 36/37 x86: Use walk_system_ream_range() instead of referring e820.map directly for tboot

In reply to Yinghai Lu

So we can make e820 to be __initdata

---
 arch/x86/kernel/tboot.c |   22 +++++++++-------------
 1 files changed, 9 insertions(+), 13 deletions(-)
arch/x86/kernel/tboot.c +9 -13
index c2f1b26..20b9531 100644
@@ -171,34 +171,30 @@ static void tboot_create_trampoline(void)
 
 #ifdef CONFIG_ACPI_SLEEP
 
-static void add_mac_region(phys_addr_t start, unsigned long size)
+static int
+add_mac_region(unsigned long start_pfn, unsigned long nr_pages, void  *arg)
 {
+	u64 start = start_pfn;
+	u64 size = nr_pages;
 	struct tboot_mac_region *mr;
-	phys_addr_t end = start + size;
 
 	if (tboot->num_mac_regions >= MAX_TB_MAC_REGIONS)
 		panic("tboot: Too many MAC regions\n");
 
 	if (start && size) {
 		mr = &tboot->mac_regions[tboot->num_mac_regions++];
-		mr->start = round_down(start, PAGE_SIZE);
-		mr->size  = round_up(end, PAGE_SIZE) - mr->start;
+		mr->start = start << PAGE_SHIFT;
+		mr->size  = (u32) (size << PAGE_SHIFT);
 	}
+
+	return 0;
 }
 
 static int tboot_setup_sleep(void)
 {
-	int i;
-
 	tboot->num_mac_regions = 0;
 
-	for (i = 0; i < e820.nr_map; i++) {
-		if ((e820.map[i].type != E820_RAM)
-		 && (e820.map[i].type != E820_RESERVED_KERN))
-			continue;
-
-		add_mac_region(e820.map[i].addr, e820.map[i].size);
-	}
+	walk_system_ram_range(0, max_pfn, NULL, add_mac_region);
 
 	tboot->acpi_sinfo.kernel_s3_resume_vector = acpi_wakeup_address;
 
Signature · 1 line
1.6.4.2
author
#42 lore raw

PATCH 37/37 x86: make e820 to be __initdata

In reply to Yinghai Lu

Finally no user after init boot stage. We can free it to save some bytes.

---
 arch/x86/include/asm/e820.h |    2 --
 arch/x86/kernel/e820.c      |    2 +-
 2 files changed, 1 insertions(+), 3 deletions(-)
arch/x86/include/asm/e820.h +0 -2
index cd7de51..f2ab72e 100644
@@ -73,8 +73,6 @@ struct e820map {
 #define BIOS_END		0x00100000
 
 #ifdef __KERNEL__
-/* see comment in arch/x86/kernel/e820.c */
-extern struct e820map e820;
 
 #if defined(CONFIG_X86_OOSTORE) && defined(CONFIG_CPU_SUP_CENTAUR)
 extern int centaur_ram_top;
arch/x86/kernel/e820.c +1 -1
index c2e18f9..ad30efd 100644
@@ -35,7 +35,7 @@
  * user can e.g. boot the original kernel with mem=1G while still booting the
  * next kernel with full memory.
  */
-struct e820map e820;
+static struct e820map __initdata e820;
 static struct e820map __initdata e820_saved;
 
 /* For PCI or other memory-mapped resources */
Signature · 1 line
1.6.4.2