i.MX25 : add Framebuffer support
Subsystems (5)
PATCH 1/3 i.MX25 : add Framebuffer support
--- drivers/video/Kconfig | 4 ++-- drivers/video/imx.c | 19 ++++++++++++++++++- 2 files changed, 20 insertions(+), 3 deletions(-)
drivers/video/Kconfig +2 -2
@@ -7,11 +7,11 @@ if VIDEO config DRIVER_VIDEO_IMX bool "i.MX framebuffer driver" - depends on ARCH_IMX1 || ARCH_IMX21 || ARCH_IMX27 + depends on ARCH_IMX1 || ARCH_IMX21 || ARCH_IMX25 || ARCH_IMX27 config IMXFB_DRIVER_VIDEO_IMX_OVERLAY bool "i.MX framebuffer overlay support" - depends on DRIVER_VIDEO_IMX && (ARCH_IMX27 || ARCH_IMX21) + depends on DRIVER_VIDEO_IMX && (ARCH_IMX27 || ARCH_IMX25 || ARCH_IMX21) config DRIVER_VIDEO_IMX_IPU bool "i.MX31/35 framebuffer driver"
drivers/video/imx.c +18 -1
@@ -258,7 +258,12 @@ static void imxfb_enable_controller(struct fb_info *info)PCCR0 |=PCCR0_LCDC_EN ;PCCR1 |=PCCR1_HCLK_LCDC ;#endif - +#ifdef CONFIG_ARCH_IMX25 +writel (readl (IMX_CCM_BASE +CCM_CGCR0 ) | (1 <<24 ) | (1 <<7 ), +IMX_CCM_BASE +CCM_CGCR0 ); +writel (readl (IMX_CCM_BASE +CCM_CGCR1 ) | (1 <<29 ), +IMX_CCM_BASE +CCM_CGCR1 ); +#endif }static void imxfb_disable_controller (struct fb_info *info)
@@ -273,6 +278,12 @@ static void imxfb_disable_controller(struct fb_info *info)PCCR0 &= ~PCCR0_LCDC_EN ;PCCR1 &= ~PCCR1_HCLK_LCDC ;#endif +#ifdef CONFIG_ARCH_IMX25 +writel (readl (IMX_CCM_BASE +CCM_CGCR0 ) & ~((1 <<24 ) | (1 <<7 )), +IMX_CCM_BASE +CCM_CGCR0 ); +writel (readl (IMX_CCM_BASE +CCM_CGCR1 ) & ~(1 <<29 ), +IMX_CCM_BASE +CCM_CGCR1 ); +#endif }/*
@@ -518,6 +529,12 @@ static int imxfb_probe(struct device_d *dev)PCCR0 &= ~PCCR0_LCDC_EN ;PCCR1 &= ~PCCR1_HCLK_LCDC ;#endif +#ifdef CONFIG_ARCH_IMX25 +writel (readl (IMX_CCM_BASE +CCM_CGCR0 ) & ~((1 <<24 ) | (1 <<7 )), +IMX_CCM_BASE +CCM_CGCR0 ); +writel (readl (IMX_CCM_BASE +CCM_CGCR1 ) & ~(1 <<29 ), +IMX_CCM_BASE +CCM_CGCR1 ); +#endif fbi =xzalloc (sizeof (*fbi)); info = &fbi->info;
Signature · 7 lines
1.6.3.3 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
PATCH 2/3 Add support for Eukrea's CPUIMX25
This boards integrates 64mB of DDR, a 256MB NAND flash, a RMII Ethernet PHY and a i.MX257 CPU.
--- arch/arm/Makefile | 1 + arch/arm/configs/eukrea_cpuimx25_defconfig | 247 +++++++++++++++++++++++ arch/arm/mach-imx/Kconfig | 10 + board/eukrea_cpuimx25/Makefile | 24 +++ board/eukrea_cpuimx25/config.h | 27 +++ board/eukrea_cpuimx25/env/bin/_update | 36 ++++ board/eukrea_cpuimx25/env/bin/boot | 53 +++++ board/eukrea_cpuimx25/env/bin/hush_hack | 1 + board/eukrea_cpuimx25/env/bin/init | 38 ++++ board/eukrea_cpuimx25/env/bin/update_kernel | 8 + board/eukrea_cpuimx25/env/bin/update_root | 8 + board/eukrea_cpuimx25/env/config | 26 +++ board/eukrea_cpuimx25/eukrea_cpuimx25.c | 285 +++++++++++++++++++++++++++ board/eukrea_cpuimx25/lowlevel_init.S | 135 +++++++++++++ 14 files changed, 899 insertions(+), 0 deletions(-) create mode 100644 arch/arm/configs/eukrea_cpuimx25_defconfig create mode 100644 board/eukrea_cpuimx25/Makefile create mode 100644 board/eukrea_cpuimx25/config.h create mode 100644 board/eukrea_cpuimx25/env/bin/_update create mode 100644 board/eukrea_cpuimx25/env/bin/boot create mode 100644 board/eukrea_cpuimx25/env/bin/hush_hack create mode 100644 board/eukrea_cpuimx25/env/bin/init create mode 100644 board/eukrea_cpuimx25/env/bin/update_kernel create mode 100644 board/eukrea_cpuimx25/env/bin/update_root create mode 100644 board/eukrea_cpuimx25/env/config create mode 100644 board/eukrea_cpuimx25/eukrea_cpuimx25.c create mode 100644 board/eukrea_cpuimx25/lowlevel_init.S
arch/arm/Makefile +1 -0
@@ -61,6 +61,7 @@ board-$(CONFIG_MACH_EDB9307A) := edb93xx board-$(CONFIG_MACH_EDB93012) := edb93xx board-$(CONFIG_MACH_EDB9315) := edb93xx board-$(CONFIG_MACH_EDB9315A) := edb93xx +board-$(CONFIG_MACH_EUKREA_CPUIMX25) := eukrea_cpuimx25 board-$(CONFIG_MACH_EUKREA_CPUIMX27) := eukrea_cpuimx27 board-$(CONFIG_MACH_FREESCALE_MX25_3STACK) := freescale-mx25-3-stack board-$(CONFIG_MACH_FREESCALE_MX35_3STACK) := freescale-mx35-3-stack
arch/arm/configs/eukrea_cpuimx25_defconfig new file +247 -0
247 lines not on this page · raw message
arch/arm/mach-imx/Kconfig +10 -0
@@ -2,6 +2,7 @@ if ARCH_IMX config ARCH_TEXT_BASE hex + default 0x83f00000 if MACH_EUKREA_CPUIMX25 default 0xa0000000 if MACH_EUKREA_CPUIMX27 default 0x08f00000 if MACH_MX1ADS default 0xc0000000 if MACH_IMX21ADS
@@ -16,6 +17,7 @@ config ARCH_TEXT_BASE default 0x08f80000 if MACH_SCB9328 config BOARDINFO + default "Eukrea CPUIMX25" if MACH_EUKREA_CPUIMX25 default "Eukrea CPUIMX27" if MACH_EUKREA_CPUIMX27 default "Freescale i.MX21 ADS" if MACH_IMX21ADS default "Freescale i.MX27 ADS" if MACH_IMX27ADS
@@ -124,6 +126,14 @@ choice prompt "i.MX25 Board Type" +config MACH_EUKREA_CPUIMX25 + bool "Eukrea CPUIMX25" + select MACH_HAS_LOWLEVEL_INIT + select HAVE_MMU + help + Say Y here if you are using the Eukrea Electromatique's CPUIMX25 + equipped with a Freescale i.MX25 Processor + config MACH_FREESCALE_MX25_3STACK bool "Freescale MX25 3stack" select HAS_CFI
board/eukrea_cpuimx25/Makefile new file +24 -0
@@ -0,0 +1,24 @@ +# +# (C) 2010 Eukrea Electromatique, Eric B��nard <[email protected]> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +obj-y += lowlevel_init.o +obj-y += eukrea_cpuimx25.o
board/eukrea_cpuimx25/config.h new file +27 -0
@@ -0,0 +1,27 @@ +/* +* (c) 2010 Eukrea Electromatique, Eric B��nard <[email protected]> +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_MX25_HCLK_FREQ 24000000 + +#endif + +/* nothing to do here yet */
board/eukrea_cpuimx25/env/bin/_update new file +36 -0
@@ -0,0 +1,36 @@ +#!/bin/sh + +if [ -z "$part" -o -z "$image" ]; then + echo "define \$part and \$image" + exit 1 +fi + +if [ ! -e "$part" ]; then + echo "Partition $part does not exist" + exit 1 +fi + +if [ $# = 1 ]; then + image=$1 +fi + +if [ x$ip = xdhcp ]; then + dhcp +fi + +ping $eth0.serverip +if [ $? -ne 0 ] ; then + echo "update aborted" + exit 1 +fi + +unprotect $part + +echo +echo "erasing partition $part" +erase $part + +echo +echo "flashing $image to $part" +echo +tftp $image $part
board/eukrea_cpuimx25/env/bin/boot new file +53 -0
53 lines not on this page · raw message
board/eukrea_cpuimx25/env/bin/hush_hack new file +1 -0
@@ -0,0 +1 @@ +nand -a /dev/nand0.*
board/eukrea_cpuimx25/env/bin/init new file +38 -0
@@ -0,0 +1,38 @@ +#!/bin/sh + +PATH=/env/bin +export PATH + +. /env/config +if [ -e /dev/nand0 ]; then + addpart /dev/nand0 $nand_parts + + # Uh, oh, hush first expands wildcards and then starts executing + # commands. What a bug! + source /env/bin/hush_hack +fi + +if [ -f /env/logo.bmp ]; then + bmp /env/logo.bmp +fi + +if [ -z $eth0.ethaddr ]; then + while [ -z $eth0.ethaddr ]; do + readline "no MAC address set for eth0. please enter the one found on your board: " eth0.ethaddr + done + echo -a /env/config "eth0.ethaddr=$eth0.ethaddr" + saveenv +fi + +echo +echo -n "Hit any key to stop autoboot: " +timeout -a $autoboot_timeout +if [ $? != 0 ]; then + echo + echo "type update_kernel [<imagename>] to update kernel into flash" + echo "type update_root [<imagename>] to update rootfs into flash" + echo + exit +fi + +boot
board/eukrea_cpuimx25/env/bin/update_kernel new file +8 -0
@@ -0,0 +1,8 @@ +#!/bin/sh + +. /env/config + +image=$uimage +part=/dev/nand0.kernel.bb + +. /env/bin/_update $1
board/eukrea_cpuimx25/env/bin/update_root new file +8 -0
@@ -0,0 +1,8 @@ +#!/bin/sh + +. /env/config + +image=$rootfs +part=/dev/nand0.root.bb + +. /env/bin/_update $1
board/eukrea_cpuimx25/env/config new file +26 -0
@@ -0,0 +1,26 @@ +#!/bin/sh + +# can be either 'net' or 'jffs2' or 'ubifs' +kernel=nand +root=jffs2 + +basedir=cpuimx25 +uimage=$basedir/uImage +rootfs=$basedir/rootfs + +autoboot_timeout=1 + +nfsroot="" +bootargs="console=ttymxc0,115200" + +nand_parts="256k(barebox)ro,128k(bareboxenv),2176k(kernel),-(root)" +rootpartnum_nand=3 + +# use 'dhcp' to do dhcp in barebox and in kernel +ip=dhcp + +# or set your networking parameters here +#eth0.ipaddr=a.b.c.d +#eth0.netmask=a.b.c.d +#eth0.gateway=a.b.c.d +eth0.serverip=192.168.1.15
board/eukrea_cpuimx25/eukrea_cpuimx25.c new file +285 -0
285 lines not on this page · raw message
board/eukrea_cpuimx25/lowlevel_init.S new file +135 -0
135 lines not on this page · raw message
Signature · 1 line
1.6.3.3
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
PATCH 3/3 freescale-mx*5-3-stack : fix __flash_header_start
_start is now exception_vectors since it was rewritten in C (not tested on these boards but compile should fail without this patch)
--- board/freescale-mx25-3-stack/3stack.c | 2 +- board/freescale-mx35-3-stack/flash_header.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)
board/freescale-mx25-3-stack/3stack.c +1 -1
@@ -41,7 +41,7 @@ extern unsigned long _stext; void __naked __flash_header_start go(void) { - __asm__ __volatile__("b _start\n" ); + __asm__ __volatile__("b exception_vectors\n" ); } struct imx_dcd_entry __dcd_entry_0x400 dcd_entry[] = {
board/freescale-mx35-3-stack/flash_header.c +1 -1
@@ -5,7 +5,7 @@ extern unsigned long _stext; void __naked __flash_header_start go(void) { - __asm__ __volatile__("b _start\n" ); + __asm__ __volatile__("b exception_vectors\n" ); } struct imx_dcd_entry __dcd_entry_0x400 dcd_entry[] = {
Signature · 7 lines
1.6.3.3 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Sascha Hauer
maintainerRe: [PATCH 3/3] freescale-mx*5-3-stack : fix __flash_header_start
Quoted 3 lines · Eric Benard
_startis nowexception_vectorssince it was rewritten in C (not tested on these boards but compile should fail without this patch)
Ok, applied to -master.
Sascha
Quoted 42 lines
Signed-off-by Eric Benard <[email protected]>--- board/freescale-mx25-3-stack/3stack.c | 2 +- board/freescale-mx35-3-stack/flash_header.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)board/freescale-mx25-3-stack/3stack.c +1
-1@@ -41,7 +41,7 @@ extern unsigned long _stext; void __naked __flash_header_start go(void) { - __asm__ __volatile__("b _start\n" ); + __asm__ __volatile__("b exception_vectors\n" ); } struct imx_dcd_entry __dcd_entry_0x400 dcd_entry[] = {board/freescale-mx35-3-stack/flash_header.c +1
-1@@ -5,7 +5,7 @@ extern unsigned long _stext; void __naked __flash_header_start go(void) { - __asm__ __volatile__("b _start\n" ); + __asm__ __volatile__("b exception_vectors\n" ); } struct imx_dcd_entry __dcd_entry_0x400 dcd_entry[] = {Signature · 7 lines
1.6.3.3 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Sascha Hauer
maintainerRe: [PATCH 2/3] Add support for Eukrea's CPUIMX25
In reply to Eric BenardHi Eric,
There are several trailing whitespaces in the patch.
Some more comments inline.
Quoted 239 lines · Eric Benard
This boards integrates 64mB of DDR, a 256MB NAND flash, a RMII Ethernet PHY and a i.MX257 CPU.
Signed-off-by Eric Benard <[email protected]>---
board/eukrea_cpuimx25/eukrea_cpuimx25.c new file +228
-0@@ -0,0 +1,285 @@ +/* +* (C) 2009 Pengutronix, Sascha Hauer <[email protected]> +* (c) 2010 Eukrea Electromatique, Eric B??nard <[email protected]> +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +* +*/ + +#include <common.h> +#include <init.h> +#include <driver.h> +#include <environment.h> +#include <mach/imx-regs.h> +#include <asm/armlinux.h> +#include <mach/gpio.h> +#include <asm/io.h> +#include <asm/mmu.h> + +#include <partition.h> +#include <asm/mach-types.h> +#include <mach/imx-nand.h> +#include <mach/imxfb.h> +#include <fec.h> +#include <nand.h> +#include <mach/imx-flash-header.h> +#include <mach/iomux-mx25.h> + +extern unsigned long _stext; + +void __naked __flash_header_start go(void) +{ + __asm__ __volatile__("b exception_vectors\n" ); +} + +struct imx_dcd_entry __dcd_entry_0x400 dcd_entry[] = { + { .ptr_type =4 , .addr =0xb8001010 , .val =0x00000004 , }, + { .ptr_type =4 , .addr =0xb8001000 , .val =0x92100000 , }, + { .ptr_type =1 , .addr =0x80000400 , .val =0x12344321 , }, + { .ptr_type =4 , .addr =0xb8001000 , .val =0xa2100000 , }, + { .ptr_type =4 , .addr =0x80000000 , .val =0x12344321 , }, + { .ptr_type =4 , .addr =0x80000000 , .val =0x12344321 , }, + { .ptr_type =4 , .addr =0xb8001000 , .val =0xb2100000 , }, + { .ptr_type =1 , .addr =0x80000033 , .val =0xda , }, + { .ptr_type =1 , .addr =0x81000000 , .val =0xff , }, + { .ptr_type =4 , .addr =0xb8001000 , .val =0x82216080 , }, + { .ptr_type =4 , .addr =0xb8001004 , .val =0x00295729 , }, + { .ptr_type =4 , .addr =0x53f80008 , .val =0x20034000 , }, +}; + +#define APP_DEST 0x80000000 + +struct imx_flash_header __flash_header_0x400 eukrea_cpuimx25_header = { + .app_code_jump_vector =TEXT_BASE +0x2000 , + .app_code_barker =APP_CODE_BARKER , + .app_code_csf =0 , + .dcd_ptr_ptr =TEXT_BASE +0x400 + offsetof(struct imx_flash_header , dcd), + .super_root_key =0 , + .dcd =TEXT_BASE +0x400 + offsetof(struct imx_flash_header , dcd_barker), + .app_dest =TEXT_BASE , + .dcd_barker =DCD_BARKER , + .dcd_block_len =sizeof (dcd_entry), +}; + +extern unsigned long __bss_start; + +unsigned long __image_len_0x400 barebox_len =0x40000 ; + +static struct fec_platform_data fec_info = { + .xcv_type =RMII , + .phy_addr =1 , +}; + +static struct device_d fec_dev = { + .name ="fec_imx" , + .map_base =IMX_FEC_BASE , + .platform_data = &fec_info, +}; + +static struct memory_platform_data sdram_pdata = { + .name ="ram0" , + .flags =DEVFS_RDWR , +}; + +static struct device_d sdram0_dev = { + .name ="mem" , + .map_base =IMX_SDRAM_CS0 , + .size =64 *1024 *1024 , + .platform_data = &sdram_pdata, +}; + +struct imx_nand_platform_data nand_info = { + .width =1 , + .hw_ecc =1 , +}; + +static struct device_d nand_dev = { + .name ="imx_nand" , + .map_base =IMX_NFC_BASE , + .platform_data = &nand_info, +}; + +static struct imx_fb_videomode imxfb_mode = { + .mode = { + .name ="CMO-QVGA" , + .refresh =60 , + .xres =320 , + .yres =240 , + .pixclock =KHZ2PICOS (6500 ), + .hsync_len =30 , + .left_margin =38 , + .right_margin =20 , + .vsync_len =3 , + .upper_margin =15 , + .lower_margin =4 , + }, + .pcr =0xCAD08B80 , + .bpp =16 , +}; + +static struct imx_fb_platform_data eukrea_cpuimx25_fb_data = { + .mode = &imxfb_mode, + .pwmr =0x00A903FF , + .lscr1 =0x00120300 , + .dmacr =0x80040060 , +}; + + +static struct device_d imxfb_dev = { + .name ="imxfb" , + .map_base =0x53fbc000 , + .size =0x1000 , + .platform_data = &eukrea_cpuimx25_fb_data, +}; + +#ifdef CONFIG_MMU +static void eukrea_cpuimx25_mmu_init (void ) +{ +mmu_init (); + +arm_create_section (0x80000000 ,0x80000000 ,128 ,PMD_SECT_DEF_CACHED ); +arm_create_section (0x90000000 ,0x80000000 ,128 ,PMD_SECT_DEF_UNCACHED ); + +setup_dma_coherent (0x10000000 ); + +mmu_enable (); +} +#else +static void eukrea_cpuimx25_mmu_init (void ) +{ +} +#endif + +static struct pad_desc eukrea_cpuimx25_pads[] = { +MX25_PAD_FEC_MDC__MDC , +MX25_PAD_FEC_MDIO__MDIO , +MX25_PAD_FEC_RDATA0__RDATA0 , +MX25_PAD_FEC_RDATA1__RDATA1 , +MX25_PAD_FEC_RX_DV__RX_DV , +MX25_PAD_FEC_TDATA0__TDATA0 , +MX25_PAD_FEC_TDATA1__TDATA1 , +MX25_PAD_FEC_TX_CLK__TX_CLK , +MX25_PAD_FEC_TX_EN__TX_EN , +/* UART1 */ +MX25_PAD_UART1_RXD__RXD_MUX , +MX25_PAD_UART1_TXD__TXD_MUX , +MX25_PAD_UART1_RTS__RTS , +MX25_PAD_UART1_CTS__CTS , +/* LCDC */ +MX25_PAD_LD0__LCDC_LD0 , +MX25_PAD_LD1__LCDC_LD1 , +MX25_PAD_LD2__LCDC_LD2 , +MX25_PAD_LD3__LCDC_LD3 , +MX25_PAD_LD4__LCDC_LD4 , +MX25_PAD_LD5__LCDC_LD5 , +MX25_PAD_LD6__LCDC_LD6 , +MX25_PAD_LD7__LCDC_LD7 , +MX25_PAD_LD8__LCDC_LD8 , +MX25_PAD_LD9__LCDC_LD9 , +MX25_PAD_LD10__LCDC_LD10 , +MX25_PAD_LD11__LCDC_LD11 , +MX25_PAD_LD12__LCDC_LD12 , +MX25_PAD_LD13__LCDC_LD13 , +MX25_PAD_LD14__LCDC_LD14 , +MX25_PAD_LD15__LCDC_LD15 , +MX25_PAD_GPIO_E__LCDC_LD16 , +MX25_PAD_GPIO_F__LCDC_LD17 , +MX25_PAD_LSCLK__LCDC_LSCLK , +MX25_PAD_OE_ACD__LCDC_OE_ACD , +MX25_PAD_VSYNC__LCDC_VSYN , +MX25_PAD_HSYNC__LCDC_HSYN , +}; + +#define IOMUXC_BASE_ADDR 0x43FAC000 +#define GPIO1_BASE_ADDR 0x53FCC000 +#define GPIO_GDIR 0x04 +#define GPIO_DR 0x00 + +static int eukrea_cpuimx25_devices_init (void ) +{ +ulong val; + +eukrea_cpuimx25_mmu_init (); + +mxc_iomux_v3_setup_multiple_pads (eukrea_cpuimx25_pads, +ARRAY_SIZE (eukrea_cpuimx25_pads)); +register_device (&fec_dev); + + nand_info.width =1 ; +register_device (&nand_dev); + +devfs_add_partition ("nand0" ,0x00000 ,0x40000 , +PARTITION_FIXED ,"self_raw" );
board/eukrea_cpuimx25/eukrea_cpuimx25.c line 238
Quoted 10 lines
board/eukrea_cpuimx25/eukrea_cpuimx25.c new file +10
-0+dev_add_bb_dev ("self_raw" ,"self0" ); + +devfs_add_partition ("nand0" ,0x40000 ,0x40000 , +PARTITION_FIXED ,"env_raw" ); +dev_add_bb_dev ("env_raw" ,"env0" ); + +register_device (&sdram0_dev); + +/* PAD PWM, MUX = GPIO1_26 */ +writel (0x5 ,IOMUXC_BASE_ADDR +0x011C );
You can add MX25_PAD_PWM__GPIO26 to the mux list above.
This reminds me of fixing the names. This should really be MX25_PAD_PWM__GPIO1_26 of course.
board/eukrea_cpuimx25/eukrea_cpuimx25.c line 241
Quoted 3 lines
board/eukrea_cpuimx25/eukrea_cpuimx25.c new file +3
-0+/* make the pins output */ + val = (1 <<26 ) |readl (GPIO1_BASE_ADDR +GPIO_GDIR ); +writel (val,GPIO1_BASE_ADDR +GPIO_GDIR );
gpio_direction_output()
board/eukrea_cpuimx25/eukrea_cpuimx25.c line 244
Quoted 3 lines
board/eukrea_cpuimx25/eukrea_cpuimx25.c new file +3
-0+/* enable LCD */ + val =readl (GPIO1_BASE_ADDR +GPIO_DR ) | (1 <<26 ); +writel (val,GPIO1_BASE_ADDR +GPIO_DR );
gpio_set_value()
Quoted 169 lines
board/eukrea_cpuimx25/eukrea_cpuimx25.c new file +41
-0+ +register_device (&imxfb_dev); + +armlinux_add_dram (&sdram0_dev); +armlinux_set_bootparams ((void *)0x80000100 ); +armlinux_set_architecture (MACH_TYPE_MX25_3DS ); + +return 0 ; +} + +device_initcall (eukrea_cpuimx25_devices_init); + +static struct device_d eukrea_cpuimx25_serial_device = { + .name ="imx_serial" , + .map_base =IMX_UART1_BASE , + .size =16 *1024 , +}; + +static int eukrea_cpuimx25_console_init (void ) +{ +writel (0x03010101 ,IMX_CCM_BASE +CCM_PCDR3 ); +register_device (&eukrea_cpuimx25_serial_device); +return 0 ; +} + +console_initcall (eukrea_cpuimx25_console_init); + +#ifdef CONFIG_NAND_IMX_BOOT +void __bare_init nand_boot(void) +{ +imx_nand_load_image ((void *)TEXT_BASE ,256 *1024 ); +} +#endif + +static int eukrea_cpuimx25_core_setup (void ) +{ +writel (0x01010103 ,IMX_CCM_BASE +CCM_PCDR2 ); +return 0 ; + +} +core_initcall (eukrea_cpuimx25_core_setup);board/eukrea_cpuimx25/lowlevel_init.S new file +122
-0@@ -0,0 +1,135 @@ +/* + * + * (c) 2007 Pengutronix, Sascha Hauer <[email protected]> + * (c) 2010 Eukrea Electromatique, Eric B??nard <[email protected]> + * Init code taken from Freescale's u-boot sources. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <mach/imx-regs.h> +#include <mach/imx-pll.h> +#include <mach/esdctl.h> +#include <asm/cache-l2x0.h> + +#define writel(val, reg) \ + ldr r0, =reg; \ + ldr r1, =val; \ + str r1, [r0]; + +#define writeb(val, reg) \ + ldr r0, =reg; \ + ldr r1, =val; \ + strb r1, [r0]; + +.section ".text_bare_init","ax" + +.globl board_init_lowlevel +board_init_lowlevel: + mov r10, lr + +#define MX25_CCM_MCR 0x64 +#define MX25_CCM_CGR0 0x0c +#define MX25_CCM_CGR1 0x10 +#define MX25_CCM_CGR2 0x14 + + /* AIPS setup - Only setup MPROTx registers. The PACR default values are good. + * Set all MPROTx to be non-bufferable, trusted for R/W, + * not forced to user-mode. + */ + writel(0x77777777, 0x43f00000) + writel(0x77777777, 0x43f00004) + writel(0x77777777, 0x53f00000) + writel(0x77777777, 0x53f00004) + + /* MAX (Multi-Layer AHB Crossbar Switch) setup + * MPR - priority for MX25 is (SDHC2/SDMA)>USBOTG>RTIC>IAHB>DAHB + */ + writel(0x00002143, 0x43f04000) + writel(0x00002143, 0x43f04100) + writel(0x00002143, 0x43f04200) + writel(0x00002143, 0x43f04300) + writel(0x00002143, 0x43f04400) + /* SGPCR - always park on last master */ + writel(0x10, 0x43f04010) + writel(0x10, 0x43f04110) + writel(0x10, 0x43f04210) + writel(0x10, 0x43f04310) + writel(0x10, 0x43f04410) + /* MGPCR - restore default values */ + writel(0x0, 0x43f04800) + writel(0x0, 0x43f04900) + writel(0x0, 0x43f04a00) + writel(0x0, 0x43f04b00) + writel(0x0, 0x43f04c00) + + /* Configure M3IF registers + * M3IF Control Register (M3IFCTL) for MX25 + * MRRP[0] = LCDC on priority list (1 << 0) = 0x00000001 + * MRRP[1] = MAX1 not on priority list (0 << 1) = 0x00000000 + * MRRP[2] = MAX0 not on priority list (0 << 2) = 0x00000000 + * MRRP[3] = USB HOST not on priority list (0 << 3) = 0x00000000 + * MRRP[4] = SDMA not on priority list (0 << 4) = 0x00000000 + * MRRP[5] = SD/ATA/FEC not on priority list (0 << 5) = 0x00000000 + * MRRP[6] = SCMFBC not on priority list (0 << 6) = 0x00000000 + * MRRP[7] = CSI not on priority list (0 << 7) = 0x00000000 + * ---------- + * 0x00000001 + */ + writel(0x1, 0xb8003000) + + /* enable all the clocks */ + writel(0x038A81A2, IMX_CCM_BASE + MX25_CCM_CGR0) + writel(0x24788F00, IMX_CCM_BASE + MX25_CCM_CGR1) + writel(0x00004438, IMX_CCM_BASE + MX25_CCM_CGR2) + writel(0x00, IMX_CCM_BASE + MX25_CCM_MCR) + +#ifdef CONFIG_NAND_IMX_BOOT + ldr sp, =0xa0f00000 /* Setup a temporary stack in SDRAM */ + + ldr r0, =IMX_NFC_BASE /* start of NFC SRAM */ + ldr r2, =IMX_NFC_BASE + 0x1000 /* end of NFC SRAM */ + + /* skip NAND boot if not running from NFC space */ + cmp pc, r0 + bls ret + cmp pc, r2 + bhi ret + + /* Move ourselves out of NFC SRAM */ + ldr r1, =TEXT_BASE + +copy_loop: + ldmia r0!, {r3-r9} /* copy from source address [r0] */ + stmia r1!, {r3-r9} /* copy to target address [r1] */ + cmp r0, r2 /* until source end addreee [r2] */ + ble copy_loop
board/eukrea_cpuimx25/lowlevel_init.S line 132
Quoted 10 lines
board/eukrea_cpuimx25/lowlevel_init.S new file +10
-0+ + ldr pc, =1f /* Jump to SDRAM */ +1: + bl nand_boot /* Load barebox from NAND Flash */ + + ldr r1, =IMX_NFC_BASE - TEXT_BASE + sub r10, r10, r1 /* adjust return address from NFC SRAM */ + /* to SDRAM */ + +#endif /* CONFIG_NAND_IMX_BOOT */
Care to rewrite this in C like some other boards already do? I will commit it as is though, no showstopper.
Sascha
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
PATCH v2 1/1 Add support for Eukrea's CPUIMX25
From: Eric Benard <[email protected]>
This boards integrates 64mB of DDR, a 256MB NAND flash, a RMII Ethernet PHY and a i.MX257 CPU.
---
v2:
- fix GPIO26 handling
- fix trailing whitespace
arch/arm/Makefile | 1 + arch/arm/configs/eukrea_cpuimx25_defconfig | 247 +++++++++++++++++++++++ arch/arm/mach-imx/Kconfig | 10 + board/eukrea_cpuimx25/Makefile | 24 +++ board/eukrea_cpuimx25/config.h | 27 +++ board/eukrea_cpuimx25/env/bin/_update | 36 ++++ board/eukrea_cpuimx25/env/bin/boot | 53 +++++ board/eukrea_cpuimx25/env/bin/hush_hack | 1 + board/eukrea_cpuimx25/env/bin/init | 38 ++++ board/eukrea_cpuimx25/env/bin/update_kernel | 8 + board/eukrea_cpuimx25/env/bin/update_root | 8 + board/eukrea_cpuimx25/env/config | 26 +++ board/eukrea_cpuimx25/eukrea_cpuimx25.c | 280 +++++++++++++++++++++++++++ board/eukrea_cpuimx25/lowlevel_init.S | 135 +++++++++++++ 14 files changed, 894 insertions(+), 0 deletions(-) create mode 100644 arch/arm/configs/eukrea_cpuimx25_defconfig create mode 100644 board/eukrea_cpuimx25/Makefile create mode 100644 board/eukrea_cpuimx25/config.h create mode 100644 board/eukrea_cpuimx25/env/bin/_update create mode 100644 board/eukrea_cpuimx25/env/bin/boot create mode 100644 board/eukrea_cpuimx25/env/bin/hush_hack create mode 100644 board/eukrea_cpuimx25/env/bin/init create mode 100644 board/eukrea_cpuimx25/env/bin/update_kernel create mode 100644 board/eukrea_cpuimx25/env/bin/update_root create mode 100644 board/eukrea_cpuimx25/env/config create mode 100644 board/eukrea_cpuimx25/eukrea_cpuimx25.c create mode 100644 board/eukrea_cpuimx25/lowlevel_init.S
arch/arm/Makefile +1 -0
@@ -61,6 +61,7 @@ board-$(CONFIG_MACH_EDB9307A) := edb93xx board-$(CONFIG_MACH_EDB93012) := edb93xx board-$(CONFIG_MACH_EDB9315) := edb93xx board-$(CONFIG_MACH_EDB9315A) := edb93xx +board-$(CONFIG_MACH_EUKREA_CPUIMX25) := eukrea_cpuimx25 board-$(CONFIG_MACH_EUKREA_CPUIMX27) := eukrea_cpuimx27 board-$(CONFIG_MACH_FREESCALE_MX25_3STACK) := freescale-mx25-3-stack board-$(CONFIG_MACH_FREESCALE_MX35_3STACK) := freescale-mx35-3-stack
arch/arm/configs/eukrea_cpuimx25_defconfig new file +247 -0
247 lines not on this page · raw message
arch/arm/mach-imx/Kconfig +10 -0
@@ -2,6 +2,7 @@ if ARCH_IMX config ARCH_TEXT_BASE hex + default 0x83f00000 if MACH_EUKREA_CPUIMX25 default 0xa0000000 if MACH_EUKREA_CPUIMX27 default 0x08f00000 if MACH_MX1ADS default 0xc0000000 if MACH_IMX21ADS
@@ -16,6 +17,7 @@ config ARCH_TEXT_BASE default 0x08f80000 if MACH_SCB9328 config BOARDINFO + default "Eukrea CPUIMX25" if MACH_EUKREA_CPUIMX25 default "Eukrea CPUIMX27" if MACH_EUKREA_CPUIMX27 default "Freescale i.MX21 ADS" if MACH_IMX21ADS default "Freescale i.MX27 ADS" if MACH_IMX27ADS
@@ -124,6 +126,14 @@ choice prompt "i.MX25 Board Type" +config MACH_EUKREA_CPUIMX25 + bool "Eukrea CPUIMX25" + select MACH_HAS_LOWLEVEL_INIT + select HAVE_MMU + help + Say Y here if you are using the Eukrea Electromatique's CPUIMX25 + equipped with a Freescale i.MX25 Processor + config MACH_FREESCALE_MX25_3STACK bool "Freescale MX25 3stack" select HAS_CFI
board/eukrea_cpuimx25/Makefile new file +24 -0
@@ -0,0 +1,24 @@ +# +# (C) 2010 Eukrea Electromatique, Eric Bénard <[email protected]> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +obj-y += lowlevel_init.o +obj-y += eukrea_cpuimx25.o
board/eukrea_cpuimx25/config.h new file +27 -0
@@ -0,0 +1,27 @@ +/* +* (c) 2010 Eukrea Electromatique, Eric Bénard <[email protected]> +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_MX25_HCLK_FREQ 24000000 + +#endif + +/* nothing to do here yet */
board/eukrea_cpuimx25/env/bin/_update new file +36 -0
@@ -0,0 +1,36 @@ +#!/bin/sh + +if [ -z "$part" -o -z "$image" ]; then + echo "define \$part and \$image" + exit 1 +fi + +if [ ! -e "$part" ]; then + echo "Partition $part does not exist" + exit 1 +fi + +if [ $# = 1 ]; then + image=$1 +fi + +if [ x$ip = xdhcp ]; then + dhcp +fi + +ping $eth0.serverip +if [ $? -ne 0 ] ; then + echo "update aborted" + exit 1 +fi + +unprotect $part + +echo +echo "erasing partition $part" +erase $part + +echo +echo "flashing $image to $part" +echo +tftp $image $part
board/eukrea_cpuimx25/env/bin/boot new file +53 -0
53 lines not on this page · raw message
board/eukrea_cpuimx25/env/bin/hush_hack new file +1 -0
@@ -0,0 +1 @@ +nand -a /dev/nand0.*
board/eukrea_cpuimx25/env/bin/init new file +38 -0
@@ -0,0 +1,38 @@ +#!/bin/sh + +PATH=/env/bin +export PATH + +. /env/config +if [ -e /dev/nand0 ]; then + addpart /dev/nand0 $nand_parts + + # Uh, oh, hush first expands wildcards and then starts executing + # commands. What a bug! + source /env/bin/hush_hack +fi + +if [ -f /env/logo.bmp ]; then + bmp /env/logo.bmp +fi + +if [ -z $eth0.ethaddr ]; then + while [ -z $eth0.ethaddr ]; do + readline "no MAC address set for eth0. please enter the one found on your board: " eth0.ethaddr + done + echo -a /env/config "eth0.ethaddr=$eth0.ethaddr" + saveenv +fi + +echo +echo -n "Hit any key to stop autoboot: " +timeout -a $autoboot_timeout +if [ $? != 0 ]; then + echo + echo "type update_kernel [<imagename>] to update kernel into flash" + echo "type update_root [<imagename>] to update rootfs into flash" + echo + exit +fi + +boot
board/eukrea_cpuimx25/env/bin/update_kernel new file +8 -0
@@ -0,0 +1,8 @@ +#!/bin/sh + +. /env/config + +image=$uimage +part=/dev/nand0.kernel.bb + +. /env/bin/_update $1
board/eukrea_cpuimx25/env/bin/update_root new file +8 -0
@@ -0,0 +1,8 @@ +#!/bin/sh + +. /env/config + +image=$rootfs +part=/dev/nand0.root.bb + +. /env/bin/_update $1
board/eukrea_cpuimx25/env/config new file +26 -0
@@ -0,0 +1,26 @@ +#!/bin/sh + +# can be either 'net' or 'jffs2' or 'ubifs' +kernel=nand +root=jffs2 + +basedir=cpuimx25 +uimage=$basedir/uImage +rootfs=$basedir/rootfs + +autoboot_timeout=1 + +nfsroot="" +bootargs="console=ttymxc0,115200" + +nand_parts="256k(barebox)ro,128k(bareboxenv),2176k(kernel),-(root)" +rootpartnum_nand=3 + +# use 'dhcp' to do dhcp in barebox and in kernel +ip=dhcp + +# or set your networking parameters here +#eth0.ipaddr=a.b.c.d +#eth0.netmask=a.b.c.d +#eth0.gateway=a.b.c.d +eth0.serverip=192.168.1.15
board/eukrea_cpuimx25/eukrea_cpuimx25.c new file +280 -0
280 lines not on this page · raw message
board/eukrea_cpuimx25/lowlevel_init.S new file +135 -0
135 lines not on this page · raw message
Signature · 7 lines
1.6.3.3 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Sascha Hauer
maintainerRe: [PATCH v2] Add support for Eukrea's CPUIMX25
Quoted 38 lines · Eric Bénard
From: Eric Benard <[email protected]>
This boards integrates 64mB of DDR, a 256MB NAND flash, a RMII Ethernet PHY and a i.MX257 CPU.
Signed-off-by Eric Bénard <[email protected]>---
v2:
- fix GPIO26 handling
- fix trailing whitespacearch/arm/Makefile | 1 + arch/arm/configs/eukrea_cpuimx25_defconfig | 247 +++++++++++++++++++++++ arch/arm/mach-imx/Kconfig | 10 + board/eukrea_cpuimx25/Makefile | 24 +++ board/eukrea_cpuimx25/config.h | 27 +++ board/eukrea_cpuimx25/env/bin/_update | 36 ++++ board/eukrea_cpuimx25/env/bin/boot | 53 +++++ board/eukrea_cpuimx25/env/bin/hush_hack | 1 + board/eukrea_cpuimx25/env/bin/init | 38 ++++ board/eukrea_cpuimx25/env/bin/update_kernel | 8 + board/eukrea_cpuimx25/env/bin/update_root | 8 + board/eukrea_cpuimx25/env/config | 26 +++ board/eukrea_cpuimx25/eukrea_cpuimx25.c | 280 +++++++++++++++++++++++++++ board/eukrea_cpuimx25/lowlevel_init.S | 135 +++++++++++++ 14 files changed, 894 insertions(+), 0 deletions(-) create mode 100644 arch/arm/configs/eukrea_cpuimx25_defconfig create mode 100644 board/eukrea_cpuimx25/Makefile create mode 100644 board/eukrea_cpuimx25/config.h create mode 100644 board/eukrea_cpuimx25/env/bin/_update create mode 100644 board/eukrea_cpuimx25/env/bin/boot create mode 100644 board/eukrea_cpuimx25/env/bin/hush_hack create mode 100644 board/eukrea_cpuimx25/env/bin/init create mode 100644 board/eukrea_cpuimx25/env/bin/update_kernel create mode 100644 board/eukrea_cpuimx25/env/bin/update_root create mode 100644 board/eukrea_cpuimx25/env/config create mode 100644 board/eukrea_cpuimx25/eukrea_cpuimx25.c create mode 100644 board/eukrea_cpuimx25/lowlevel_init.S
[snip]
Quoted 210 lines
board/eukrea_cpuimx25/eukrea_cpuimx25.c new file +204
-0@@ -0,0 +1,280 @@ +/* +* (C) 2009 Pengutronix, Sascha Hauer <[email protected]> +* (c) 2010 Eukrea Electromatique, Eric Bénard <[email protected]> +* +* See file CREDITS for list of people who contributed to this +* project. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +* +*/ + +#include <common.h> +#include <init.h> +#include <driver.h> +#include <environment.h> +#include <mach/imx-regs.h> +#include <asm/armlinux.h> +#include <mach/gpio.h> +#include <asm/io.h> +#include <asm/mmu.h> + +#include <partition.h> +#include <asm/mach-types.h> +#include <mach/imx-nand.h> +#include <mach/imxfb.h> +#include <fec.h> +#include <nand.h> +#include <mach/imx-flash-header.h> +#include <mach/iomux-mx25.h> + +extern unsigned long _stext; + +void __naked __flash_header_start go(void) +{ + __asm__ __volatile__("b exception_vectors\n" ); +} + +struct imx_dcd_entry __dcd_entry_0x400 dcd_entry[] = { + { .ptr_type =4 , .addr =0xb8001010 , .val =0x00000004 , }, + { .ptr_type =4 , .addr =0xb8001000 , .val =0x92100000 , }, + { .ptr_type =1 , .addr =0x80000400 , .val =0x12344321 , }, + { .ptr_type =4 , .addr =0xb8001000 , .val =0xa2100000 , }, + { .ptr_type =4 , .addr =0x80000000 , .val =0x12344321 , }, + { .ptr_type =4 , .addr =0x80000000 , .val =0x12344321 , }, + { .ptr_type =4 , .addr =0xb8001000 , .val =0xb2100000 , }, + { .ptr_type =1 , .addr =0x80000033 , .val =0xda , }, + { .ptr_type =1 , .addr =0x81000000 , .val =0xff , }, + { .ptr_type =4 , .addr =0xb8001000 , .val =0x82216080 , }, + { .ptr_type =4 , .addr =0xb8001004 , .val =0x00295729 , }, + { .ptr_type =4 , .addr =0x53f80008 , .val =0x20034000 , }, +}; + +#define APP_DEST 0x80000000 + +struct imx_flash_header __flash_header_0x400 eukrea_cpuimx25_header = { + .app_code_jump_vector =TEXT_BASE +0x2000 , + .app_code_barker =APP_CODE_BARKER , + .app_code_csf =0 , + .dcd_ptr_ptr =TEXT_BASE +0x400 + offsetof(struct imx_flash_header , dcd), + .super_root_key =0 , + .dcd =TEXT_BASE +0x400 + offsetof(struct imx_flash_header , dcd_barker), + .app_dest =TEXT_BASE , + .dcd_barker =DCD_BARKER , + .dcd_block_len =sizeof (dcd_entry), +}; + +extern unsigned long __bss_start; + +unsigned long __image_len_0x400 barebox_len =0x40000 ; + +static struct fec_platform_data fec_info = { + .xcv_type =RMII , + .phy_addr =1 , +}; + +static struct device_d fec_dev = { + .name ="fec_imx" , + .map_base =IMX_FEC_BASE , + .platform_data = &fec_info, +}; + +static struct memory_platform_data sdram_pdata = { + .name ="ram0" , + .flags =DEVFS_RDWR , +}; + +static struct device_d sdram0_dev = { + .name ="mem" , + .map_base =IMX_SDRAM_CS0 , + .size =64 *1024 *1024 , + .platform_data = &sdram_pdata, +}; + +struct imx_nand_platform_data nand_info = { + .width =1 , + .hw_ecc =1 , +}; + +static struct device_d nand_dev = { + .name ="imx_nand" , + .map_base =IMX_NFC_BASE , + .platform_data = &nand_info, +}; + +static struct imx_fb_videomode imxfb_mode = { + .mode = { + .name ="CMO-QVGA" , + .refresh =60 , + .xres =320 , + .yres =240 , + .pixclock =KHZ2PICOS (6500 ), + .hsync_len =30 , + .left_margin =38 , + .right_margin =20 , + .vsync_len =3 , + .upper_margin =15 , + .lower_margin =4 , + }, + .pcr =0xCAD08B80 , + .bpp =16 , +}; + +static struct imx_fb_platform_data eukrea_cpuimx25_fb_data = { + .mode = &imxfb_mode, + .pwmr =0x00A903FF , + .lscr1 =0x00120300 , + .dmacr =0x80040060 , +}; + + +static struct device_d imxfb_dev = { + .name ="imxfb" , + .map_base =0x53fbc000 , + .size =0x1000 , + .platform_data = &eukrea_cpuimx25_fb_data, +}; + +#ifdef CONFIG_MMU +static void eukrea_cpuimx25_mmu_init (void ) +{ +mmu_init (); + +arm_create_section (0x80000000 ,0x80000000 ,128 ,PMD_SECT_DEF_CACHED ); +arm_create_section (0x90000000 ,0x80000000 ,128 ,PMD_SECT_DEF_UNCACHED ); + +setup_dma_coherent (0x10000000 ); + +mmu_enable (); +} +#else +static void eukrea_cpuimx25_mmu_init (void ) +{ +} +#endif + +static struct pad_desc eukrea_cpuimx25_pads[] = { +MX25_PAD_FEC_MDC__MDC , +MX25_PAD_FEC_MDIO__MDIO , +MX25_PAD_FEC_RDATA0__RDATA0 , +MX25_PAD_FEC_RDATA1__RDATA1 , +MX25_PAD_FEC_RX_DV__RX_DV , +MX25_PAD_FEC_TDATA0__TDATA0 , +MX25_PAD_FEC_TDATA1__TDATA1 , +MX25_PAD_FEC_TX_CLK__TX_CLK , +MX25_PAD_FEC_TX_EN__TX_EN , +/* UART1 */ +MX25_PAD_UART1_RXD__RXD_MUX , +MX25_PAD_UART1_TXD__TXD_MUX , +MX25_PAD_UART1_RTS__RTS , +MX25_PAD_UART1_CTS__CTS , +/* LCDC */ +MX25_PAD_LD0__LCDC_LD0 , +MX25_PAD_LD1__LCDC_LD1 , +MX25_PAD_LD2__LCDC_LD2 , +MX25_PAD_LD3__LCDC_LD3 , +MX25_PAD_LD4__LCDC_LD4 , +MX25_PAD_LD5__LCDC_LD5 , +MX25_PAD_LD6__LCDC_LD6 , +MX25_PAD_LD7__LCDC_LD7 , +MX25_PAD_LD8__LCDC_LD8 , +MX25_PAD_LD9__LCDC_LD9 , +MX25_PAD_LD10__LCDC_LD10 , +MX25_PAD_LD11__LCDC_LD11 , +MX25_PAD_LD12__LCDC_LD12 , +MX25_PAD_LD13__LCDC_LD13 , +MX25_PAD_LD14__LCDC_LD14 , +MX25_PAD_LD15__LCDC_LD15 , +MX25_PAD_GPIO_E__LCDC_LD16 , +MX25_PAD_GPIO_F__LCDC_LD17 , +MX25_PAD_LSCLK__LCDC_LSCLK , +MX25_PAD_OE_ACD__LCDC_OE_ACD ,
board/eukrea_cpuimx25/eukrea_cpuimx25.c line 214
Quoted 10 lines
board/eukrea_cpuimx25/eukrea_cpuimx25.c new file +10
-0+MX25_PAD_VSYNC__LCDC_VSYN , +MX25_PAD_HSYNC__LCDC_HSYN , +/* BACKLIGHT CONTROL */ + MX25_PAD_PWM__GPIO26, +}; + +#define IOMUXC_BASE_ADDR 0x43FAC000 +#define GPIO1_BASE_ADDR 0x53FCC000 +#define GPIO_GDIR 0x04 +#define GPIO_DR 0x00
These are not needed anymore.
Sascha
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Re: [PATCH 2/3] Add support for Eukrea's CPUIMX25
In reply to Sascha HauerHi Sascha,
v2 of the patch passed through checkpatch so no trailing whitespaces should left.
Quoted 3 lines · Sascha Hauer
Care to rewrite this in C like some other boards already do? I will commit it as is though, no showstopper.
I put this on the todo list, exercise seems interesting so I'll do it asap ;-)
Thanks,
Eric
_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Sascha Hauer
maintainerRe: [PATCH 2/3] Add support for Eukrea's CPUIMX25
Quoted 11 lines · Eric Bénard
Hi Sascha,
v2 of the patch passed through checkpatch so no trailing whitespaces should left.
Quoted 3 lines · Sascha Hauer
Care to rewrite this in C like some other boards already do? I will commit it as is though, no showstopper.
I put this on the todo list, exercise seems interesting so I'll do it asap ;-)
Ok, the patch looks ok apart from the comment I made. I'll wait applying it for some time. Just ping me before the next release if you want me to apply the assembler version.
Sascha
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Sascha Hauer
maintainerQuoted 1 line · Eric Benard
Signed-off-by Eric Benard <[email protected]>
Ok, applied to -next.
Sascha
Quoted 76 lines
--- drivers/video/Kconfig | 4 ++-- drivers/video/imx.c | 19 ++++++++++++++++++- 2 files changed, 20 insertions(+), 3 deletions(-)drivers/video/Kconfig +2
-2@@ -7,11 +7,11 @@ if VIDEO config DRIVER_VIDEO_IMX bool "i.MX framebuffer driver" - depends on ARCH_IMX1 || ARCH_IMX21 || ARCH_IMX27 + depends on ARCH_IMX1 || ARCH_IMX21 || ARCH_IMX25 || ARCH_IMX27 config IMXFB_DRIVER_VIDEO_IMX_OVERLAY bool "i.MX framebuffer overlay support" - depends on DRIVER_VIDEO_IMX && (ARCH_IMX27 || ARCH_IMX21) + depends on DRIVER_VIDEO_IMX && (ARCH_IMX27 || ARCH_IMX25 || ARCH_IMX21) config DRIVER_VIDEO_IMX_IPU bool "i.MX31/35 framebuffer driver"drivers/video/imx.c +18
-1@@ -258,7 +258,12 @@ static void imxfb_enable_controller(struct fb_info *info)PCCR0 |=PCCR0_LCDC_EN ;PCCR1 |=PCCR1_HCLK_LCDC ;#endif - +#ifdef CONFIG_ARCH_IMX25 +writel (readl (IMX_CCM_BASE +CCM_CGCR0 ) | (1 <<24 ) | (1 <<7 ), +IMX_CCM_BASE +CCM_CGCR0 ); +writel (readl (IMX_CCM_BASE +CCM_CGCR1 ) | (1 <<29 ), +IMX_CCM_BASE +CCM_CGCR1 ); +#endif }static void imxfb_disable_controller (struct fb_info *info)@@ -273,6 +278,12 @@ static void imxfb_disable_controller(struct fb_info *info)PCCR0 &= ~PCCR0_LCDC_EN ;PCCR1 &= ~PCCR1_HCLK_LCDC ;#endif +#ifdef CONFIG_ARCH_IMX25 +writel (readl (IMX_CCM_BASE +CCM_CGCR0 ) & ~((1 <<24 ) | (1 <<7 )), +IMX_CCM_BASE +CCM_CGCR0 ); +writel (readl (IMX_CCM_BASE +CCM_CGCR1 ) & ~(1 <<29 ), +IMX_CCM_BASE +CCM_CGCR1 ); +#endif }/* @@ -518,6 +529,12 @@ static int imxfb_probe(struct device_d *dev)PCCR0 &= ~PCCR0_LCDC_EN ;PCCR1 &= ~PCCR1_HCLK_LCDC ;#endif +#ifdef CONFIG_ARCH_IMX25 +writel (readl (IMX_CCM_BASE +CCM_CGCR0 ) & ~((1 <<24 ) | (1 <<7 )), +IMX_CCM_BASE +CCM_CGCR0 ); +writel (readl (IMX_CCM_BASE +CCM_CGCR1 ) & ~(1 <<29 ), +IMX_CCM_BASE +CCM_CGCR1 ); +#endif fbi =xzalloc (sizeof (*fbi)); info = &fbi->info;Signature · 7 lines
1.6.3.3 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox