s3c-hsotg driver updates / fixes
Subsystems (2)
This series includes the usb-xtal rate addition/fix from Marus which has been submitted (so please ignore if merge is already pending) and fixes for some of the problems that have been seen.
This is not the full set of fixes, as there are still some more complicated issues to sort out with things such as stall handling on non-ep0 endpoints which are being investiagted.
Thanks to Thomas Abraham and Kukjin Kim at Samsung for providing help and further information to help track down these problems.
PATCH 1/6 USB: s3c_hsotg: Add support for external USB clock
From: Maurus Cuelenaere <[email protected]>
The PLL that drives the USB clock supports 3 input clocks: 12, 24 and 48Mhz. This patch adds support to the USB driver for setting the correct register bit according to the given clock.
This depends on the following patch:
[PATCH] ARM: S3C64XX: Add USB external clock definition
--- drivers/usb/gadget/s3c-hsotg.c | 19 +++++++++++++++++++ 1 files changed, 19 insertions(+), 0 deletions(-)
drivers/usb/gadget/s3c-hsotg.c +19 -0
@@ -23,6 +23,7 @@#include <linux/delay.h> #include <linux/io.h> #include <linux/slab.h> +#include <linux/clk.h> #include <linux/usb/ch9.h> #include <linux/usb/gadget.h>
@@ -2699,6 +2700,7 @@ static void __devinit s3c_hsotg_initep(struct s3c_hsotg *hsotg,*/ static void s3c_hsotg_otgreset (struct s3c_hsotg *hsotg) { +struct clk *xusbxti;u32 osc;writel (0 ,S3C_PHYPWR );
@@ -2706,6 +2708,23 @@ static void s3c_hsotg_otgreset(struct s3c_hsotg *hsotg) osc = hsotg->plat->is_osc ?S3C_PHYCLK_EXT_OSC :0 ; + xusbxti =clk_get (hsotg->dev,"xusbxti" ); +if (xusbxti && !IS_ERR (xusbxti)) { +switch (clk_get_rate (xusbxti)) { +case 12000000 : + osc |=S3C_PHYCLK_CLKSEL_12M ; +break ; +case 24000000 : + osc |=S3C_PHYCLK_CLKSEL_24M ; +break ; +default : +case 48000000 : +/* default reference clock */ +break ; + } +clk_put (xusbxti); + } +writel (osc |0x10 ,S3C_PHYCLK );/* issue a full set of resets to the otg and core */
Signature · 1 line
1.6.3.3
PATCH 2/6 USB: s3c_hsotg: define USB_GADGET_DUALSPEED in Kconfig
From: Maurus Cuelenaere <[email protected]>
The s3c_hsotg driver sets usb_gadget->is_dualspeed to 1, yet it doesn't define USB_GADGET_DUALSPEED in Kconfig. This triggers a NULL pointer dereference in the composite driver (which is fixed in another patch).
--- drivers/usb/gadget/Kconfig | 1 + 1 files changed, 1 insertions(+), 0 deletions(-)
drivers/usb/gadget/Kconfig +1 -0
@@ -295,6 +295,7 @@ config USB_GADGET_S3C_HSOTG boolean "S3C HS/OtG USB Device controller" depends on S3C_DEV_USB_HSOTG select USB_GADGET_S3C_HSOTG_PIO + select USB_GADGET_DUALSPEED help The Samsung S3C64XX USB2.0 high-speed gadget controller integrated into the S3C64XX series SoC.
Signature · 1 line
1.6.3.3
A message that is not in the archive (sent off-list or not yet received): 1274762213-3404-3-git-send-email-ben-linux-elnMNo+KYs3YtjvyW6yDsg@public.gmane.org
PATCH 3/6 USB: s3c-hsotg: Ensure TX FIFO addresses setup when initialising FIFOs
Some versions of the S3C HS OtG block startup with overlapping TX FIFO information, so change the fifo_init code to ensure that known values are set into the FIFO registers at initialisation/reset time.
This also ensures that the FIFO RAM pointers are in a known state before use.
--- drivers/usb/gadget/s3c-hsotg.c | 25 +++++++++++++++++++++++++ 1 files changed, 25 insertions(+), 0 deletions(-)
drivers/usb/gadget/s3c-hsotg.c +25 -0
@@ -298,6 +298,11 @@ static void s3c_hsotg_ctrl_epint(struct s3c_hsotg *hsotg,*/ static void s3c_hsotg_init_fifo (struct s3c_hsotg *hsotg) { +unsigned int ep; +unsigned int addr; +unsigned int size; +u32 val; +/* the ryu 2.6.24 release ahs writel(0x1C0, hsotg->regs + S3C_GRXFSIZ); writel(S3C_GNPTXFSIZ_NPTxFStAddr(0x200) |
@@ -311,6 +316,26 @@ static void s3c_hsotg_init_fifo(struct s3c_hsotg *hsotg)writel (S3C_GNPTXFSIZ_NPTxFStAddr (2048 ) |S3C_GNPTXFSIZ_NPTxFDep (0x1C0 ), hsotg->regs +S3C_GNPTXFSIZ ); + +/* arange all the rest of the TX FIFOs, as some versions of this +* block have overlapping default addresses. This also ensures +* that if the settings have been changed, then they are set to +* known values. */ + +/* start at the end of the GNPTXFSIZ, rounded up */ + addr =2048 +1024 ; + size =768 ; + +/* currently we allocate TX FIFOs for all possible endpoints, +* and assume that they are all the same size. */ + +for (ep =0 ; ep <=15 ; ep++) { + val = addr; + val |= size << S3C_DPTXFSIZn_DPTxFSize_SHIFT; + addr += size; + +writel (val, hsotg->regs +S3C_DPTXFSIZn (ep)); + } }/**
Signature · 6 lines
1.6.3.3 -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
PATCH 4/6 USB: s3c-hsotg: SoftDisconnect minimum 3ms
The shortest period SoftDisconnect can be asserted for is 3 milliseconds according to the V210 datasheet, so ensure that we add an msleep() to the registration code to enforce this.
--- drivers/usb/gadget/s3c-hsotg.c | 3 +++ 1 files changed, 3 insertions(+), 0 deletions(-)
drivers/usb/gadget/s3c-hsotg.c +3 -0
@@ -2600,6 +2600,9 @@ int usb_gadget_register_driver(struct usb_gadget_driver *driver)writel (S3C_DCTL_CGOUTNak | S3C_DCTL_CGNPInNAK, hsotg->regs +S3C_DCTL ); +/* must be at-least 3ms to allow bus to see disconnect */ +msleep (3 ); +/* remove the soft-disconnect and let's go */ __bic32 (hsotg->regs +S3C_DCTL , S3C_DCTL_SftDiscon);
Signature · 1 line
1.6.3.3
PATCH 5/6 USB: s3c-hsotg: Ensure FIFOs are fully flushed after layout
According to the design guide, if the FIFO layout is changed, then the FIFOs must be flushed to ensure all FIFO pointers are correct.
--- drivers/usb/gadget/s3c-hsotg.c | 26 ++++++++++++++++++++++++++ 1 files changed, 26 insertions(+), 0 deletions(-)
drivers/usb/gadget/s3c-hsotg.c +26 -0
@@ -301,6 +301,7 @@ static void s3c_hsotg_init_fifo(struct s3c_hsotg *hsotg)unsigned int ep;unsigned int addr;unsigned int size; +int timeout;u32 val;/* the ryu 2.6.24 release ahs
@@ -336,6 +337,31 @@ static void s3c_hsotg_init_fifo(struct s3c_hsotg *hsotg)writel (val, hsotg->regs +S3C_DPTXFSIZn (ep)); } + +/* according to p428 of the design guide, we need to ensure that +* all fifos are flushed before continuing */ + +writel (S3C_GRSTCTL_TxFNum (0x10 ) | S3C_GRSTCTL_TxFFlsh | + S3C_GRSTCTL_RxFFlsh, hsotg->regs +S3C_GRSTCTL ); + +/* wait until the fifos are both flushed */ + timeout =100 ; +while (1 ) { + val =readl (hsotg->regs +S3C_GRSTCTL ); + +if ((val & (S3C_GRSTCTL_TxFFlsh | S3C_GRSTCTL_RxFFlsh)) ==0 ) +break ; + +if (--timeout ==0 ) { +dev_err (hsotg->dev, +"%s: timeout flushing fifos (GRSTCTL=%08x)\n" , + __func__, val); + } + +udelay (1 ); + } + +dev_dbg (hsotg->dev,"FIFOs reset, timeout at %d\n" , timeout); }/**
Signature · 1 line
1.6.3.3
PATCH 6/6 USB: s3c-hsotg: Enable soft disconnect during initialization
From: Thomas Abraham <[email protected]>
Enable soft disconnect bit the OTG core during initialization. Without this, the host sees that a gadget is connected and tries to enumerate. The soft disconnect should be enabled until the USB gadget driver is registered with this otg driver.
--- drivers/usb/gadget/s3c-hsotg.c | 3 +++ 1 files changed, 3 insertions(+), 0 deletions(-)
drivers/usb/gadget/s3c-hsotg.c +3 -0
@@ -2803,6 +2803,9 @@ static void s3c_hsotg_init(struct s3c_hsotg *hsotg)writel (0 , hsotg->regs +S3C_DAINTMSK ); +/* Be in disconnected state until gadget is registered */ +__orr32 (hsotg->regs +S3C_DCTL , S3C_DCTL_SftDiscon); +if (0 ) {/* post global nak until we're ready */ writel(S3C_DCTL_SGNPInNAK | S3C_DCTL_SGOUTNak,
Signature · 1 line
1.6.3.3
A message that is not in the archive (sent off-list or not yet received): 1274762213-3404-6-git-send-email-ben-linux-elnMNo+KYs3YtjvyW6yDsg@public.gmane.org
Re: [PATCH 5/6] USB: s3c-hsotg: Ensure FIFOs are fully flushed after layout
Quoted 21 lines · Ben Dooks
According to the design guide, if the FIFO layout is changed, then the FIFOs must be flushed to ensure all FIFO pointers are correct.
Signed-off-by Ben Dooks <[email protected]>---
drivers/usb/gadget/s3c-hsotg.c | 26 ++++++++++++++++++++++++++1 files changed, 26 insertions(+), 0 deletions(-)drivers/usb/gadget/s3c-hsotg.c +1
-0@@ -301,6 +301,7 @@ static void s3c_hsotg_init_fifo(struct s3c_hsotg *hsotg) unsigned int ep; unsigned int addr; unsigned int size; + int timeout; u32 val; /* the ryu 2.6.24 release ahs
drivers/usb/gadget/s3c-hsotg.c static void s3c_hsotg_init_fifo(struct s3c_hsotg *hsotg) · line 342
Quoted 6 lines
drivers/usb/gadget/s3c-hsotg.c +3
-0@@ -336,6 +337,31 @@ static void s3c_hsotg_init_fifo(struct s3c_hsotg *hsotg) writel(val, hsotg->regs + S3C_DPTXFSIZn(ep)); } + + /* according to p428 of the design guide, we need to ensure that +* all fifos are flushed before continuing */
Please see Documentation/CodingStyle for multi-line comments.
Quoted 13 lines
drivers/usb/gadget/s3c-hsotg.c +13
-0+ + writel(S3C_GRSTCTL_TxFNum(0x10) | S3C_GRSTCTL_TxFFlsh | + S3C_GRSTCTL_RxFFlsh, hsotg->regs + S3C_GRSTCTL); + + /* wait until the fifos are both flushed */ + timeout = 100; + while (1) { + val = readl(hsotg->regs + S3C_GRSTCTL); + + if ((val & (S3C_GRSTCTL_TxFFlsh | S3C_GRSTCTL_RxFFlsh)) == 0) + break; + + if (--timeout == 0) {
drivers/usb/gadget/s3c-hsotg.c static void s3c_hsotg_init_fifo(struct s3c_hsotg *hsotg) · line 365
Quoted 10 lines
drivers/usb/gadget/s3c-hsotg.c +9
-0+ dev_err(hsotg->dev, + "%s: timeout flushing fifos (GRSTCTL=%08x)\n", + __func__, val); + } + + udelay(1); + } + + dev_dbg(hsotg->dev, "FIFOs reset, timeout at %d\n", timeout); }
Regards,
Maulik
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [PATCH 3/6] USB: s3c-hsotg: Ensure TX FIFO addresses setup when initialising FIFOs
In reply to Ben DooksQuoted 29 lines · Ben Dooks
Some versions of the S3C HS OtG block startup with overlapping TX FIFO information, so change the
fifo_initcode to ensure that known values are set into the FIFO registers at initialisation/reset time.This also ensures that the FIFO RAM pointers are in a known state before use.
Signed-off-by Ben Dooks <[email protected]>---
drivers/usb/gadget/s3c-hsotg.c | 25 +++++++++++++++++++++++++1 files changed, 25 insertions(+), 0 deletions(-)drivers/usb/gadget/s3c-hsotg.c +5
-0@@ -298,6 +298,11 @@ static void s3c_hsotg_ctrl_epint(struct s3c_hsotg *hsotg,*/ static void s3c_hsotg_init_fifo(struct s3c_hsotg *hsotg) { + unsigned int ep; + unsigned int addr; + unsigned int size; + u32 val; + /* the ryu 2.6.24 release ahswritel(0x1C0, hsotg->regs + S3C_GRXFSIZ); writel(S3C_GNPTXFSIZ_NPTxFStAddr(0x200) |
drivers/usb/gadget/s3c-hsotg.c +0
-0@@ -311,6 +316,26 @@ static void s3c_hsotg_init_fifo(struct s3c_hsotg *hsotg)
Quoted 8 lines
writel(S3C_GNPTXFSIZ_NPTxFStAddr(2048) |
S3C_GNPTXFSIZ_NPTxFDep(0x1C0),
hsotg->regs+S3C_GNPTXFSIZ);
+
+ /* arange all the rest of the TX FIFOs, as some versions of this
+ * block have overlapping default addresses. This also ensures
+ * that if the settings have been changed, then they are set to
+ * known values. */
Please see Documentation/CodingStyle for multi-line comments.
drivers/usb/gadget/s3c-hsotg.c static void s3c_hsotg_init_fifo(struct s3c_hsotg *hsotg) · line 330
Quoted 7 lines
drivers/usb/gadget/s3c-hsotg.c +7
-0+ + /* start at the end of the GNPTXFSIZ, rounded up */ + addr = 2048 + 1024; + size = 768; + + /* currently we allocate TX FIFOs for all possible endpoints, +* and assume that they are all the same size. */
Same here.
Quoted 9 lines
drivers/usb/gadget/s3c-hsotg.c +8
-0+ + for (ep = 0; ep <= 15; ep++) { + val = addr; + val |= size << S3C_DPTXFSIZn_DPTxFSize_SHIFT; + addr += size; + + writel(val, hsotg->regs + S3C_DPTXFSIZn(ep)); + }}
Regards,
Maulik
A message that is not in the archive (sent off-list or not yet received): AANLkTin6EEiXOGyZjmOEd39g_eUxGBJEV2yMdnwtAQbh-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org
Re: [PATCH 3/6] USB: s3c-hsotg: Ensure TX FIFO addresses setup when initialising FIFOs
Quoted 51 lines · Maulik Mankad
Quoted 29 lines · Ben Dooks
Some versions of the S3C HS OtG block startup with overlapping TX FIFO information, so change the
fifo_initcode to ensure that known values are set into the FIFO registers at initialisation/reset time.This also ensures that the FIFO RAM pointers are in a known state before use.
Signed-off-by Ben Dooks <[email protected]>---
drivers/usb/gadget/s3c-hsotg.c | 25 +++++++++++++++++++++++++1 files changed, 25 insertions(+), 0 deletions(-)drivers/usb/gadget/s3c-hsotg.c +5
-0@@ -298,6 +298,11 @@ static void s3c_hsotg_ctrl_epint(struct s3c_hsotg *hsotg,*/ static void s3c_hsotg_init_fifo(struct s3c_hsotg *hsotg) { + unsigned int ep; + unsigned int addr; + unsigned int size; + u32 val; + /* the ryu 2.6.24 release ahswritel(0x1C0, hsotg->regs + S3C_GRXFSIZ); writel(S3C_GNPTXFSIZ_NPTxFStAddr(0x200) |
drivers/usb/gadget/s3c-hsotg.c +0
-0@@ -311,6 +316,26 @@ static void s3c_hsotg_init_fifo(struct s3c_hsotg *hsotg)Quoted 8 lines
writel(S3C_GNPTXFSIZ_NPTxFStAddr(2048) |
S3C_GNPTXFSIZ_NPTxFDep(0x1C0),
hsotg->regs+S3C_GNPTXFSIZ);
+
+ /* arange all the rest of the TX FIFOs, as some versions of this
+ * block have overlapping default addresses. This also ensures
+ * that if the settings have been changed, then they are set to
+ * known values. */Please see
Documentation/CodingStylefor multi-line comments.drivers/usb/gadget/s3c-hsotg.c static void s3c_hsotg_init_fifo(struct s3c_hsotg *hsotg) · line 330
Quoted 7 lines
drivers/usb/gadget/s3c-hsotg.c +7
-0+ + /* start at the end of the GNPTXFSIZ, rounded up */ + addr = 2048 + 1024; + size = 768; + + /* currently we allocate TX FIFOs for all possible endpoints, +* and assume that they are all the same size. */ Same here.
Quoted 12 lines
Quoted 9 lines
drivers/usb/gadget/s3c-hsotg.c +8
-0+ + for (ep = 0; ep <= 15; ep++) { + val = addr; + val |= size << S3C_DPTXFSIZn_DPTxFSize_SHIFT; + addr += size; + + writel(val, hsotg->regs + S3C_DPTXFSIZn(ep)); + }}
Regards,
Maulik
ok, fixed both,
Signature · 9 lines
Ben Q: What's a light-year? A: One-third less calories than a regular year. -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [PATCH 1/6] USB: s3c_hsotg: Add support for external USB clock
In reply to Ben DooksQuoted 8 lines · Ben Dooks
From: Maurus Cuelenaere <[email protected]>
The PLL that drives the USB clock supports 3 input clocks: 12, 24 and 48Mhz. This patch adds support to the USB driver for setting the correct register bit according to the given clock.
This depends on the following patch:
[PATCH] ARM: S3C64XX: Add USB external clock definition
Care to take this through the arm tree then?
thanks,
greg k-h
Re: [PATCH 1/6] USB: s3c_hsotg: Add support for external USB clock
Op 01-06-10 22:41, Greg KH schreef:
Quoted 8 lines · Ben Dooks
Quoted 7 lines
From: Maurus Cuelenaere <[email protected]>
The PLL that drives the USB clock supports 3 input clocks: 12, 24 and 48Mhz. This patch adds support to the USB driver for setting the correct register bit according to the given clock.
Quoted 9 lines
Quoted 3 lines
This depends on the following patch:
[PATCH] ARM: S3C64XX: Add USB external clock definitionCare to take this through the arm tree then?
thanks,
greg k-h
If I'm not mistaken, this patch is already in Ben's tree (the USB_GADGET_DUALSPEED one too)
Signature · 1 line
Maurus Cuelenaere