Skip to contentSkip to conversation

atl1c: Add AR8151 v2 support and change L0s/L1 routine

PATCH Applied [email protected] 2 participants 2 messages May 31, 2010 – Jun 1, 2010

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 atl1c: Add AR8151 v2 support and change L0s/L1 routine

From: [email protected]

Add AR8151 v2.0 Gigabit 1000 support
Change jumbo frame size to 6K
Update L0s/L1 rountine
when link speed is 100M or 1G, set L1 link timer to 4 for l1d_2 and l2c_b2 set L1 link timer to 7 for l2c_b, set L1 link timer to 0xF for others.
Update atl1c_suspend routine
just refactory the function, add atl1c_phy_power_saving routine, when Wake On Lan enable, this func will be called to save power, it will reautoneg PHY to 10/100M speed depend on the link partners link capability.
Update atl1c_configure_des_ring
do not use l2c_b default SRAM configuration.

Signed-off-by [email protected]

---

 drivers/net/atl1c/atl1c.h      |    9 +-
 drivers/net/atl1c/atl1c_hw.c   |  107 +++++++++++--
 drivers/net/atl1c/atl1c_hw.h   |   49 ++++++-
 drivers/net/atl1c/atl1c_main.c |  348 +++++++++++++++++++++++-----------------
 4 files changed, 345 insertions(+), 168 deletions(-)
drivers/net/atl1c/atl1c.h +7 -2
index 84ae905..52abbbd 100644
@@ -73,7 +73,8 @@
 #define FULL_DUPLEX        2
 
 #define AT_RX_BUF_SIZE		(ETH_FRAME_LEN + VLAN_HLEN + ETH_FCS_LEN)
-#define MAX_JUMBO_FRAME_SIZE 	(9*1024)
+#define MAX_JUMBO_FRAME_SIZE	(6*1024)
+#define MAX_TSO_FRAME_SIZE      (7*1024)
 #define MAX_TX_OFFLOAD_THRESH	(9*1024)
 
 #define AT_MAX_RECEIVE_QUEUE    4
@@ -87,10 +88,11 @@
 #define AT_MAX_INT_WORK		5
 #define AT_TWSI_EEPROM_TIMEOUT 	100
 #define AT_HW_MAX_IDLE_DELAY 	10
-#define AT_SUSPEND_LINK_TIMEOUT 28
+#define AT_SUSPEND_LINK_TIMEOUT 100
 
 #define AT_ASPM_L0S_TIMER	6
 #define AT_ASPM_L1_TIMER	12
+#define AT_LCKDET_TIMER		12
 
 #define ATL1C_PCIE_L0S_L1_DISABLE 	0x01
 #define ATL1C_PCIE_PHY_RESET		0x02
@@ -316,6 +318,7 @@ enum atl1c_nic_type {
 	athr_l2c_b,
 	athr_l2c_b2,
 	athr_l1d,
+	athr_l1d_2,
 };
 
 enum atl1c_trans_queue {
@@ -392,6 +395,8 @@ struct atl1c_hw {
 	u16 subsystem_id;
 	u16 subsystem_vendor_id;
 	u8 revision_id;
+	u16 phy_id1;
+	u16 phy_id2;
 
 	u32 intr_mask;
 	u8 dmaw_dly_cnt;
drivers/net/atl1c/atl1c_hw.c +92 -15

159 lines not on this page · raw message

drivers/net/atl1c/atl1c_hw.h +46 -3

107 lines not on this page · raw message

drivers/net/atl1c/atl1c_main.c +200 -148

638 lines not on this page · raw message

maintainer Applied
#1 lore raw

From: <[email protected]>
Date: Mon, 31 May 2010 14:42:16 +0800

Quoted 15 lines

From: [email protected]

Add AR8151 v2.0 Gigabit 1000 support
Change jumbo frame size to 6K
Update L0s/L1 rountine
when link speed is 100M or 1G, set L1 link timer to 4 for l1d_2 and l2c_b2 set L1 link timer to 7 for l2c_b, set L1 link timer to 0xF for others.
Update atl1c_suspend routine
just refactory the function, add atl1c_phy_power_saving routine, when Wake On Lan enable, this func will be called to save power, it will reautoneg PHY to 10/100M speed depend on the link partners link capability.
Update atl1c_configure_des_ring
do not use l2c_b default SRAM configuration.

Quoted 1 line
Signed-off-by [email protected]

Applied, thank you.