Skip to contentSkip to conversation

tty: BKL removal

PATCH In review Arnd Bergmann 4 participants 37 messages Jun 1, 2010 – Jun 17, 2010

Subsystems (8)
lore
Share & tools
lore

Arnd Bergmann

author maintainer
#0 lore raw

cover tty: BKL removal

Hi Greg,

As promised, here is a resend of the patches from
both Alan and myself, making the BKL optional
in the TTY layer. Please apply to your tty-next
tree.

Arnd

--

Alan Cox (20):
stallion: prune lock_kernel calls
istallion: use bit ops for the board flags
riscom8: kill use of lock_kernel
isicom: kill off the BKL
rocket: kill BKL
synclink: kill the big kernel lock
cyclades: Kill off BKL usage
epca: Kill the big kernel lock
specialix; Kill the BKL
synclink: reworking locking a bit
tty: serial - fix various misuses/mishandlings of port->tty
tty: serial - fix tty back references in termios
tty: serial - fix tty referencing in set_ldisc
vc: Locking clean up
tty: Make vt's have a tty_port
tty: Move the vt_tty field from the vc_data into the standard
tty_port
serial: Change the wait for carrier locking
serial: add port helpers
serial: trim locking on the helpers
serial: Use block_til_ready helper

Arnd Bergmann (11):
tty: replace BKL with a new tty_lock
tty: never hold BTM while getting tty_mutex
tty: fix console_sem lock order
cdc-acm: remove dead code
tty: introduce wait_event_interruptible_tty
tty: reorder ldisc locking
tty: untangle locking of wait_until_sent
tty: remove tty_lock_nested
tty: implement BTM as mutex instead of BKL
tty: release BTM while sleeping in block_til_ready 8250: fix set_ldisc operation

 drivers/char/Makefile          |    1 +
 drivers/char/amiserial.c       |   25 +++-
 drivers/char/briq_panel.c      |    6 +-
 drivers/char/cyclades.c        |   22 ++--
 drivers/char/epca.c            |    4 +-
 drivers/char/ip2/ip2main.c     |    4 +
 drivers/char/isicom.c          |   13 +-
 drivers/char/istallion.c       |   68 ++++++-----
 drivers/char/keyboard.c        |   10 +-
 drivers/char/n_hdlc.c          |   16 +-
 drivers/char/n_r3964.c         |   10 +-
 drivers/char/pty.c             |   26 ++--
 drivers/char/riscom8.c         |   14 +-
 drivers/char/rocket.c          |   28 +++--
 drivers/char/selection.c       |   13 ++-
 drivers/char/serial167.c       |    8 +-
 drivers/char/specialix.c       |   13 +-
 drivers/char/stallion.c        |   20 ++-
 drivers/char/sx.c              |   12 +-
 drivers/char/synclink.c        |   21 ++--
 drivers/char/synclink_gt.c     |   92 +++++++-------
 drivers/char/synclinkmp.c      |   43 +++---
 drivers/char/tty_io.c          |  134 +++++++++++---------
 drivers/char/tty_ldisc.c       |   43 +++++--
 drivers/char/tty_mutex.c       |   47 +++++++
 drivers/char/tty_port.c        |    4 +-
 drivers/char/vc_screen.c       |    4 +-
 drivers/char/vt.c              |   19 ++-
 drivers/char/vt_ioctl.c        |   14 +-
 drivers/serial/21285.c         |   10 +-
 drivers/serial/68328serial.c   |    2 +
 drivers/serial/68360serial.c   |    4 +-
 drivers/serial/8250.c          |    9 +-
 drivers/serial/bfin_5xx.c      |    7 +-
 drivers/serial/crisv10.c       |    8 +-
 drivers/serial/imx.c           |   10 +-
 drivers/serial/ioc3_serial.c   |    9 +-
 drivers/serial/ioc4_serial.c   |    9 +-
 drivers/serial/max3100.c       |    7 +-
 drivers/serial/serial_core.c   |  281 +++++++++++++++++++---------------------
 drivers/usb/class/cdc-acm.c    |   12 +--
 drivers/video/console/vgacon.c |    2 -
 include/linux/console_struct.h |    3 +-
 include/linux/istallion.h      |    2 +-
 include/linux/serial_core.h    |    2 +-
 include/linux/tty.h            |   67 ++++++++++
 lib/Kconfig.debug              |   10 ++
 47 files changed, 679 insertions(+), 509 deletions(-)
 create mode 100644 drivers/char/tty_mutex.c
author maintainer
#1 lore raw

PATCH 1/31 stallion: prune lock_kernel calls

From: Alan Cox <[email protected]>

Remove unneeded tty layer lock kernel bits. Relock the needed bits using the port mutex. The istallion still has brd state races but those are not new or introduced by the removal of the lock_kernel logic.

---
 drivers/char/istallion.c |   22 +++++++++++++---------
 drivers/char/stallion.c  |   20 ++++++++++++--------
 2 files changed, 25 insertions(+), 17 deletions(-)
drivers/char/istallion.c +13 -9
index 4e395c9..750650c 100644
@@ -14,6 +14,7 @@
  *	the Free Software Foundation; either version 2 of the License, or
  *	(at your option) any later version.
  *
+ *	FIXME: brdp->state needs proper locking.
  */
 
 /*****************************************************************************/
@@ -4011,6 +4012,7 @@ static int stli_getbrdstats(combrd_t __user *bp)
 		return -ENODEV;
 
 	memset(&stli_brdstats, 0, sizeof(combrd_t));
+
 	stli_brdstats.brd = brdp->brdnr;
 	stli_brdstats.type = brdp->brdtype;
 	stli_brdstats.hwid = 0;
@@ -4076,10 +4078,13 @@ static int stli_portcmdstats(struct tty_struct *tty, struct stliport *portp)
 	if (brdp == NULL)
 		return -ENODEV;
 
+	mutex_lock(&portp->port.mutex);
 	if (brdp->state & BST_STARTED) {
 		if ((rc = stli_cmdwait(brdp, portp, A_GETSTATS,
-		    &stli_cdkstats, sizeof(asystats_t), 1)) < 0)
+		    &stli_cdkstats, sizeof(asystats_t), 1)) < 0) {
+			mutex_unlock(&portp->port.mutex);
 			return rc;
+		}
 	} else {
 		memset(&stli_cdkstats, 0, sizeof(asystats_t));
 	}
@@ -4124,6 +4129,7 @@ static int stli_portcmdstats(struct tty_struct *tty, struct stliport *portp)
 	stli_comstats.modem = stli_cdkstats.dcdcnt;
 	stli_comstats.hwid = stli_cdkstats.hwid;
 	stli_comstats.signals = stli_mktiocm(stli_cdkstats.signals);
+	mutex_unlock(&portp->port.mutex);
 
 	return 0;
 }
@@ -4186,15 +4192,20 @@ static int stli_clrportstats(struct stliport *portp, comstats_t __user *cp)
 	if (!brdp)
 		return -ENODEV;
 
+	mutex_lock(&portp->port.mutex);
+
 	if (brdp->state & BST_STARTED) {
-		if ((rc = stli_cmdwait(brdp, portp, A_CLEARSTATS, NULL, 0, 0)) < 0)
+		if ((rc = stli_cmdwait(brdp, portp, A_CLEARSTATS, NULL, 0, 0)) < 0) {
+			mutex_unlock(&portp->port.mutex);
 			return rc;
+		}
 	}
 
 	memset(&stli_comstats, 0, sizeof(comstats_t));
 	stli_comstats.brd = portp->brdnr;
 	stli_comstats.panel = portp->panelnr;
 	stli_comstats.port = portp->portnr;
+	mutex_unlock(&portp->port.mutex);
 
 	if (copy_to_user(cp, &stli_comstats, sizeof(comstats_t)))
 		return -EFAULT;
@@ -4266,8 +4277,6 @@ static long stli_memioctl(struct file *fp, unsigned int cmd, unsigned long arg)
 	done = 0;
 	rc = 0;
 
-	lock_kernel();
-
 	switch (cmd) {
 	case COM_GETPORTSTATS:
 		rc = stli_getportstats(NULL, NULL, argp);
@@ -4290,8 +4299,6 @@ static long stli_memioctl(struct file *fp, unsigned int cmd, unsigned long arg)
 		done++;
 		break;
 	}
-	unlock_kernel();
-
 	if (done)
 		return rc;
 
@@ -4308,8 +4315,6 @@ static long stli_memioctl(struct file *fp, unsigned int cmd, unsigned long arg)
 	if (brdp->state == 0)
 		return -ENODEV;
 
-	lock_kernel();
-
 	switch (cmd) {
 	case STL_BINTR:
 		EBRDINTR(brdp);
@@ -4332,7 +4337,6 @@ static long stli_memioctl(struct file *fp, unsigned int cmd, unsigned long arg)
 		rc = -ENOIOCTLCMD;
 		break;
 	}
-	unlock_kernel();
 	return rc;
 }
 
drivers/char/stallion.c +12 -8
index 6049fd7..f2167f8 100644
@@ -807,7 +807,6 @@ static void stl_waituntilsent(struct tty_struct *tty, int timeout)
 		timeout = HZ;
 	tend = jiffies + timeout;
 
-	lock_kernel();
 	while (stl_datastate(portp)) {
 		if (signal_pending(current))
 			break;
@@ -815,7 +814,6 @@ static void stl_waituntilsent(struct tty_struct *tty, int timeout)
 		if (time_after_eq(jiffies, tend))
 			break;
 	}
-	unlock_kernel();
 }
 
 /*****************************************************************************/
@@ -1029,6 +1027,8 @@ static int stl_getserial(struct stlport *portp, struct serial_struct __user *sp)
 	pr_debug("stl_getserial(portp=%p,sp=%p)\n", portp, sp);
 
 	memset(&sio, 0, sizeof(struct serial_struct));
+
+	mutex_lock(&portp->port.mutex);
 	sio.line = portp->portnr;
 	sio.port = portp->ioaddr;
 	sio.flags = portp->port.flags;
@@ -1048,6 +1048,7 @@ static int stl_getserial(struct stlport *portp, struct serial_struct __user *sp)
 	brdp = stl_brds[portp->brdnr];
 	if (brdp != NULL)
 		sio.irq = brdp->irq;
+	mutex_unlock(&portp->port.mutex);
 
 	return copy_to_user(sp, &sio, sizeof(struct serial_struct)) ? -EFAULT : 0;
 }
@@ -1069,12 +1070,15 @@ static int stl_setserial(struct tty_struct *tty, struct serial_struct __user *sp
 
 	if (copy_from_user(&sio, sp, sizeof(struct serial_struct)))
 		return -EFAULT;
+	mutex_lock(&portp->port.mutex);
 	if (!capable(CAP_SYS_ADMIN)) {
 		if ((sio.baud_base != portp->baud_base) ||
 		    (sio.close_delay != portp->close_delay) ||
 		    ((sio.flags & ~ASYNC_USR_MASK) !=
-		    (portp->port.flags & ~ASYNC_USR_MASK)))
+		    (portp->port.flags & ~ASYNC_USR_MASK))) {
+			mutex_unlock(&portp->port.mutex);
 			return -EPERM;
+		}
 	} 
 
 	portp->port.flags = (portp->port.flags & ~ASYNC_USR_MASK) |
@@ -1083,6 +1087,7 @@ static int stl_setserial(struct tty_struct *tty, struct serial_struct __user *sp
 	portp->close_delay = sio.close_delay;
 	portp->closing_wait = sio.closing_wait;
 	portp->custom_divisor = sio.custom_divisor;
+	mutex_unlock(&portp->port.mutex);
 	stl_setport(portp, tty->termios);
 	return 0;
 }
@@ -1147,8 +1152,6 @@ static int stl_ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd
 
 	rc = 0;
 
-	lock_kernel();
-
 	switch (cmd) {
 	case TIOCGSERIAL:
 		rc = stl_getserial(portp, argp);
@@ -1173,7 +1176,6 @@ static int stl_ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd
 		rc = -ENOIOCTLCMD;
 		break;
 	}
-	unlock_kernel();
 	return rc;
 }
 
@@ -2327,6 +2329,7 @@ static int stl_getportstats(struct tty_struct *tty, struct stlport *portp, comst
 			return -ENODEV;
 	}
 
+	mutex_lock(&portp->port.mutex);
 	portp->stats.state = portp->istate;
 	portp->stats.flags = portp->port.flags;
 	portp->stats.hwid = portp->hwid;
@@ -2358,6 +2361,7 @@ static int stl_getportstats(struct tty_struct *tty, struct stlport *portp, comst
 		(STL_TXBUFSIZE - (tail - head));
 
 	portp->stats.signals = (unsigned long) stl_getsignals(portp);
+	mutex_unlock(&portp->port.mutex);
 
 	return copy_to_user(cp, &portp->stats,
 			    sizeof(comstats_t)) ? -EFAULT : 0;
@@ -2382,10 +2386,12 @@ static int stl_clrportstats(struct stlport *portp, comstats_t __user *cp)
 			return -ENODEV;
 	}
 
+	mutex_lock(&portp->port.mutex);
 	memset(&portp->stats, 0, sizeof(comstats_t));
 	portp->stats.brd = portp->brdnr;
 	portp->stats.panel = portp->panelnr;
 	portp->stats.port = portp->portnr;
+	mutex_unlock(&portp->port.mutex);
 	return copy_to_user(cp, &portp->stats,
 			    sizeof(comstats_t)) ? -EFAULT : 0;
 }
@@ -2451,7 +2457,6 @@ static long stl_memioctl(struct file *fp, unsigned int cmd, unsigned long arg)
 		return -ENODEV;
 	rc = 0;
 
-	lock_kernel();
 	switch (cmd) {
 	case COM_GETPORTSTATS:
 		rc = stl_getportstats(NULL, NULL, argp);
@@ -2472,7 +2477,6 @@ static long stl_memioctl(struct file *fp, unsigned int cmd, unsigned long arg)
 		rc = -ENOIOCTLCMD;
 		break;
 	}
-	unlock_kernel();
 	return rc;
 }
 
Signature · 1 line
1.7.0.4
author maintainer
#2 lore raw

PATCH 2/31 istallion: use bit ops for the board flags

In reply to Arnd Bergmann

From: Alan Cox <[email protected]>

This lets us avoid problems with races on the flag changes

---
 drivers/char/istallion.c  |   36 ++++++++++++++++++------------------
 include/linux/istallion.h |    2 +-
 2 files changed, 19 insertions(+), 19 deletions(-)
drivers/char/istallion.c +18 -18
index 750650c..5e9a81d 100644
@@ -14,7 +14,6 @@
  *	the Free Software Foundation; either version 2 of the License, or
  *	(at your option) any later version.
  *
- *	FIXME: brdp->state needs proper locking.
  */
 
 /*****************************************************************************/
@@ -204,9 +203,9 @@ static int		stli_shared;
  *	the board has been detected, and whether it is actually running a slave
  *	or not.
  */
-#define	BST_FOUND	0x1
-#define	BST_STARTED	0x2
-#define	BST_PROBED	0x4
+#define	BST_FOUND	0
+#define	BST_STARTED	1
+#define	BST_PROBED	2
 
 /*
  *	Define the set of port state flags. These are marked for internal
@@ -817,7 +816,7 @@ static int stli_open(struct tty_struct *tty, struct file *filp)
 	brdp = stli_brds[brdnr];
 	if (brdp == NULL)
 		return -ENODEV;
-	if ((brdp->state & BST_STARTED) == 0)
+	if (!test_bit(BST_STARTED, &brdp->state))
 		return -ENODEV;
 	portnr = MINOR2PORT(minordev);
 	if (portnr > brdp->nrports)
@@ -1847,7 +1846,7 @@ static void stli_portinfo(struct seq_file *m, struct stlibrd *brdp, struct stlip
 	rc = stli_portcmdstats(NULL, portp);
 
 	uart = "UNKNOWN";
-	if (brdp->state & BST_STARTED) {
+	if (test_bit(BST_STARTED, &brdp->state)) {
 		switch (stli_comstats.hwid) {
 		case 0:	uart = "2681"; break;
 		case 1:	uart = "SC26198"; break;
@@ -1856,7 +1855,7 @@ static void stli_portinfo(struct seq_file *m, struct stlibrd *brdp, struct stlip
 	}
 	seq_printf(m, "%d: uart:%s ", portnr, uart);
 
-	if ((brdp->state & BST_STARTED) && (rc >= 0)) {
+	if (test_bit(BST_STARTED, &brdp->state) && rc >= 0) {
 		char sep;
 
 		seq_printf(m, "tx:%d rx:%d", (int) stli_comstats.txtotal,
@@ -2356,7 +2355,7 @@ static void stli_poll(unsigned long arg)
 		brdp = stli_brds[brdnr];
 		if (brdp == NULL)
 			continue;
-		if ((brdp->state & BST_STARTED) == 0)
+		if (!test_bit(BST_STARTED, &brdp->state))
 			continue;
 
 		spin_lock(&brd_lock);
@@ -3141,7 +3140,7 @@ static int stli_initecp(struct stlibrd *brdp)
 	}
 
 
-	brdp->state |= BST_FOUND;
+	set_bit(BST_FOUND, &brdp->state);
 	return 0;
 err_unmap:
 	iounmap(brdp->membase);
@@ -3298,7 +3297,7 @@ static int stli_initonb(struct stlibrd *brdp)
 	brdp->panels[0] = brdp->nrports;
 
 
-	brdp->state |= BST_FOUND;
+	set_bit(BST_FOUND, &brdp->state);
 	return 0;
 err_unmap:
 	iounmap(brdp->membase);
@@ -3408,7 +3407,7 @@ stli_donestartup:
 	spin_unlock_irqrestore(&brd_lock, flags);
 
 	if (rc == 0)
-		brdp->state |= BST_STARTED;
+		set_bit(BST_STARTED, &brdp->state);
 
 	if (! stli_timeron) {
 		stli_timeron++;
@@ -3711,7 +3710,7 @@ static int __devinit stli_pciprobe(struct pci_dev *pdev,
 	if (retval)
 		goto err_null;
 
-	brdp->state |= BST_PROBED;
+	set_bit(BST_PROBED, &brdp->state);
 	pci_set_drvdata(pdev, brdp);
 
 	EBRDENABLE(brdp);
@@ -3842,7 +3841,7 @@ static int __init stli_initbrds(void)
 			brdp = stli_brds[i];
 			if (brdp == NULL)
 				continue;
-			if (brdp->state & BST_FOUND) {
+			if (test_bit(BST_FOUND, &brdp->state)) {
 				EBRDENABLE(brdp);
 				brdp->enable = NULL;
 				brdp->disable = NULL;
@@ -4079,7 +4078,7 @@ static int stli_portcmdstats(struct tty_struct *tty, struct stliport *portp)
 		return -ENODEV;
 
 	mutex_lock(&portp->port.mutex);
-	if (brdp->state & BST_STARTED) {
+	if (test_bit(BST_STARTED, &brdp->state)) {
 		if ((rc = stli_cmdwait(brdp, portp, A_GETSTATS,
 		    &stli_cdkstats, sizeof(asystats_t), 1)) < 0) {
 			mutex_unlock(&portp->port.mutex);
@@ -4194,7 +4193,7 @@ static int stli_clrportstats(struct stliport *portp, comstats_t __user *cp)
 
 	mutex_lock(&portp->port.mutex);
 
-	if (brdp->state & BST_STARTED) {
+	if (test_bit(BST_STARTED, &brdp->state)) {
 		if ((rc = stli_cmdwait(brdp, portp, A_CLEARSTATS, NULL, 0, 0)) < 0) {
 			mutex_unlock(&portp->port.mutex);
 			return rc;
@@ -4323,10 +4322,10 @@ static long stli_memioctl(struct file *fp, unsigned int cmd, unsigned long arg)
 		rc = stli_startbrd(brdp);
 		break;
 	case STL_BSTOP:
-		brdp->state &= ~BST_STARTED;
+		clear_bit(BST_STARTED, &brdp->state);
 		break;
 	case STL_BRESET:
-		brdp->state &= ~BST_STARTED;
+		clear_bit(BST_STARTED, &brdp->state);
 		EBRDRESET(brdp);
 		if (stli_shared == 0) {
 			if (brdp->reenable != NULL)
@@ -4382,7 +4381,8 @@ static void istallion_cleanup_isa(void)
 	unsigned int j;
 
 	for (j = 0; (j < stli_nrbrds); j++) {
-		if ((brdp = stli_brds[j]) == NULL || (brdp->state & BST_PROBED))
+		if ((brdp = stli_brds[j]) == NULL ||
+				test_bit(BST_PROBED, &brdp->state))
 			continue;
 
 		stli_cleanup_ports(brdp);
include/linux/istallion.h +1 -1
index 7faca98..ad700a6 100644
@@ -86,7 +86,7 @@ struct stlibrd {
 	unsigned long	magic;
 	unsigned int	brdnr;
 	unsigned int	brdtype;
-	unsigned int	state;
+	unsigned long	state;
 	unsigned int	nrpanels;
 	unsigned int	nrports;
 	unsigned int	nrdevs;
Signature · 1 line
1.7.0.4
author maintainer
#3 lore raw

PATCH 3/31 riscom8: kill use of lock_kernel

In reply to Arnd Bergmann

From: Alan Cox <[email protected]>

The riscom8 board uses lock_kernel to protect bits of the port setting ioctl logic. We can use the port mutex for this as the logic is internal and will also lock set versus open (a locking property that has been lost somewhere along the way)

---
 drivers/char/riscom8.c |   14 ++++++++------
 1 files changed, 8 insertions(+), 6 deletions(-)
drivers/char/riscom8.c +8 -6
index b02332a..af4de1f 100644
@@ -47,7 +47,6 @@
 #include <linux/init.h>
 #include <linux/delay.h>
 #include <linux/tty_flip.h>
-#include <linux/smp_lock.h>
 #include <linux/spinlock.h>
 #include <linux/device.h>
 
@@ -1184,6 +1183,7 @@ static int rc_set_serial_info(struct tty_struct *tty, struct riscom_port *port,
 	if (copy_from_user(&tmp, newinfo, sizeof(tmp)))
 		return -EFAULT;
 
+	mutex_lock(&port->port.mutex);
 	change_speed = ((port->port.flags & ASYNC_SPD_MASK) !=
 			(tmp.flags & ASYNC_SPD_MASK));
 
@@ -1191,8 +1191,10 @@ static int rc_set_serial_info(struct tty_struct *tty, struct riscom_port *port,
 		if ((tmp.close_delay != port->port.close_delay) ||
 		    (tmp.closing_wait != port->port.closing_wait) ||
 		    ((tmp.flags & ~ASYNC_USR_MASK) !=
-		     (port->port.flags & ~ASYNC_USR_MASK)))
+		     (port->port.flags & ~ASYNC_USR_MASK))) {
+			mutex_unlock(&port->port.mutex);
 			return -EPERM;
+		}
 		port->port.flags = ((port->port.flags & ~ASYNC_USR_MASK) |
 			       (tmp.flags & ASYNC_USR_MASK));
 	} else  {
@@ -1208,6 +1210,7 @@ static int rc_set_serial_info(struct tty_struct *tty, struct riscom_port *port,
 		rc_change_speed(tty, bp, port);
 		spin_unlock_irqrestore(&riscom_lock, flags);
 	}
+	mutex_unlock(&port->port.mutex);
 	return 0;
 }
 
@@ -1220,12 +1223,15 @@ static int rc_get_serial_info(struct riscom_port *port,
 	memset(&tmp, 0, sizeof(tmp));
 	tmp.type = PORT_CIRRUS;
 	tmp.line = port - rc_port;
+
+	mutex_lock(&port->port.mutex);
 	tmp.port = bp->base;
 	tmp.irq  = bp->irq;
 	tmp.flags = port->port.flags;
 	tmp.baud_base = (RC_OSCFREQ + CD180_TPC/2) / CD180_TPC;
 	tmp.close_delay = port->port.close_delay * HZ/100;
 	tmp.closing_wait = port->port.closing_wait * HZ/100;
+	mutex_unlock(&port->port.mutex);
 	tmp.xmit_fifo_size = CD180_NFIFO;
 	return copy_to_user(retinfo, &tmp, sizeof(tmp)) ? -EFAULT : 0;
 }
@@ -1242,14 +1248,10 @@ static int rc_ioctl(struct tty_struct *tty, struct file *filp,
 
 	switch (cmd) {
 	case TIOCGSERIAL:
-		lock_kernel();
 		retval = rc_get_serial_info(port, argp);
-		unlock_kernel();
 		break;
 	case TIOCSSERIAL:
-		lock_kernel();
 		retval = rc_set_serial_info(tty, port, argp);
-		unlock_kernel();
 		break;
 	default:
 		retval = -ENOIOCTLCMD;
Signature · 1 line
1.7.0.4
author maintainer
#4 lore raw

PATCH 4/31 isicom: kill off the BKL

In reply to Arnd Bergmann

From: Alan Cox <[email protected]>

As with the others we can use the port mutex to get the needed locking properties and fix the race with open.

---
 drivers/char/isicom.c |   13 +++++--------
 1 files changed, 5 insertions(+), 8 deletions(-)
drivers/char/isicom.c +5 -8
index 98310e1..c27e9d2 100644
@@ -124,7 +124,6 @@
 #include <linux/fs.h>
 #include <linux/sched.h>
 #include <linux/serial.h>
-#include <linux/smp_lock.h>
 #include <linux/mm.h>
 #include <linux/interrupt.h>
 #include <linux/timer.h>
@@ -872,7 +871,6 @@ static struct tty_port *isicom_find_port(struct tty_struct *tty)
 static int isicom_open(struct tty_struct *tty, struct file *filp)
 {
 	struct isi_port *port;
-	struct isi_board *card;
 	struct tty_port *tport;
 
 	tport = isicom_find_port(tty);
@@ -1118,8 +1116,7 @@ static int isicom_set_serial_info(struct tty_struct *tty,
 	if (copy_from_user(&newinfo, info, sizeof(newinfo)))
 		return -EFAULT;
 
-	lock_kernel();
-
+	mutex_lock(&port->port.mutex);
 	reconfig_port = ((port->port.flags & ASYNC_SPD_MASK) !=
 		(newinfo.flags & ASYNC_SPD_MASK));
 
@@ -1128,7 +1125,7 @@ static int isicom_set_serial_info(struct tty_struct *tty,
 				(newinfo.closing_wait != port->port.closing_wait) ||
 				((newinfo.flags & ~ASYNC_USR_MASK) !=
 				(port->port.flags & ~ASYNC_USR_MASK))) {
-			unlock_kernel();
+			mutex_unlock(&port->port.mutex);
 			return -EPERM;
 		}
 		port->port.flags = ((port->port.flags & ~ASYNC_USR_MASK) |
@@ -1145,7 +1142,7 @@ static int isicom_set_serial_info(struct tty_struct *tty,
 		isicom_config_port(tty);
 		spin_unlock_irqrestore(&port->card->card_lock, flags);
 	}
-	unlock_kernel();
+	mutex_unlock(&port->port.mutex);
 	return 0;
 }
 
@@ -1154,7 +1151,7 @@ static int isicom_get_serial_info(struct isi_port *port,
 {
 	struct serial_struct out_info;
 
-	lock_kernel();
+	mutex_lock(&port->port.mutex);
 	memset(&out_info, 0, sizeof(out_info));
 /*	out_info.type = ? */
 	out_info.line = port - isi_ports;
@@ -1164,7 +1161,7 @@ static int isicom_get_serial_info(struct isi_port *port,
 /*	out_info.baud_base = ? */
 	out_info.close_delay = port->port.close_delay;
 	out_info.closing_wait = port->port.closing_wait;
-	unlock_kernel();
+	mutex_unlock(&port->port.mutex);
 	if (copy_to_user(info, &out_info, sizeof(out_info)))
 		return -EFAULT;
 	return 0;
Signature · 1 line
1.7.0.4
author maintainer
#5 lore raw

PATCH 5/31 rocket: kill BKL

In reply to Arnd Bergmann

From: Alan Cox <[email protected]>

We can use the port mutex for this and also for the hangup path so removing the problematic use of the hangup mutex in this driver. Fix up the locking on the various port flags while we are at it.

Ultimately this driver needs to be using tty_port_ helpers which would sort this out far better.

---
 drivers/char/rocket.c |   28 +++++++++++++++++++---------
 1 files changed, 19 insertions(+), 9 deletions(-)
drivers/char/rocket.c +19 -9
index 0e29a23..79c3bc6 100644
@@ -73,7 +73,6 @@
 #include <linux/tty_driver.h>
 #include <linux/tty_flip.h>
 #include <linux/serial.h>
-#include <linux/smp_lock.h>
 #include <linux/string.h>
 #include <linux/fcntl.h>
 #include <linux/ptrace.h>
@@ -1017,6 +1016,7 @@ static void rp_close(struct tty_struct *tty, struct file *filp)
 	if (tty_port_close_start(port, tty, filp) == 0)
 		return;
 
+	mutex_lock(&port->mutex);
 	cp = &info->channel;
 	/*
 	 * Before we drop DTR, make sure the UART transmitter
@@ -1060,9 +1060,13 @@ static void rp_close(struct tty_struct *tty, struct file *filp)
 			info->xmit_buf = NULL;
 		}
 	}
+	spin_lock_irq(&port->lock);
 	info->port.flags &= ~(ASYNC_INITIALIZED | ASYNC_CLOSING | ASYNC_NORMAL_ACTIVE);
 	tty->closing = 0;
+	spin_unlock_irq(&port->lock);
+	mutex_unlock(&port->mutex);
 	tty_port_tty_set(port, NULL);
+
 	wake_up_interruptible(&port->close_wait);
 	complete_all(&info->close_wait);
 	atomic_dec(&rp_num_ports_open);
@@ -1210,11 +1214,13 @@ static int get_config(struct r_port *info, struct rocket_config __user *retinfo)
 	if (!retinfo)
 		return -EFAULT;
 	memset(&tmp, 0, sizeof (tmp));
+	mutex_lock(&info->port.mutex);
 	tmp.line = info->line;
 	tmp.flags = info->flags;
 	tmp.close_delay = info->port.close_delay;
 	tmp.closing_wait = info->port.closing_wait;
 	tmp.port = rcktpt_io_addr[(info->line >> 5) & 3];
+	mutex_unlock(&info->port.mutex);
 
 	if (copy_to_user(retinfo, &tmp, sizeof (*retinfo)))
 		return -EFAULT;
@@ -1229,10 +1235,13 @@ static int set_config(struct tty_struct *tty, struct r_port *info,
 	if (copy_from_user(&new_serial, new_info, sizeof (new_serial)))
 		return -EFAULT;
 
+	mutex_lock(&info->port.mutex);
 	if (!capable(CAP_SYS_ADMIN))
 	{
-		if ((new_serial.flags & ~ROCKET_USR_MASK) != (info->flags & ~ROCKET_USR_MASK))
+		if ((new_serial.flags & ~ROCKET_USR_MASK) != (info->flags & ~ROCKET_USR_MASK)) {
+			mutex_unlock(&info->port.mutex);
 			return -EPERM;
+		}
 		info->flags = ((info->flags & ~ROCKET_USR_MASK) | (new_serial.flags & ROCKET_USR_MASK));
 		configure_r_port(tty, info, NULL);
 		return 0;
@@ -1250,6 +1259,7 @@ static int set_config(struct tty_struct *tty, struct r_port *info,
 		tty->alt_speed = 230400;
 	if ((info->flags & ROCKET_SPD_MASK) == ROCKET_SPD_WARP)
 		tty->alt_speed = 460800;
+	mutex_unlock(&info->port.mutex);
 
 	configure_r_port(tty, info, NULL);
 	return 0;
@@ -1325,8 +1335,6 @@ static int rp_ioctl(struct tty_struct *tty, struct file *file,
 	if (cmd != RCKP_GET_PORTS && rocket_paranoia_check(info, "rp_ioctl"))
 		return -ENXIO;
 
-	lock_kernel();
-
 	switch (cmd) {
 	case RCKP_GET_STRUCT:
 		if (copy_to_user(argp, info, sizeof (struct r_port)))
@@ -1350,7 +1358,6 @@ static int rp_ioctl(struct tty_struct *tty, struct file *file,
 	default:
 		ret = -ENOIOCTLCMD;
 	}
-	unlock_kernel();
 	return ret;
 }
 
@@ -1471,7 +1478,6 @@ static void rp_wait_until_sent(struct tty_struct *tty, int timeout)
 	       jiffies);
 	printk(KERN_INFO "cps=%d...\n", info->cps);
 #endif
-	lock_kernel();
 	while (1) {
 		txcnt = sGetTxCnt(cp);
 		if (!txcnt) {
@@ -1499,7 +1505,6 @@ static void rp_wait_until_sent(struct tty_struct *tty, int timeout)
 			break;
 	}
 	__set_current_state(TASK_RUNNING);
-	unlock_kernel();
 #ifdef ROCKET_DEBUG_WAIT_UNTIL_SENT
 	printk(KERN_INFO "txcnt = %d (jiff=%lu)...done\n", txcnt, jiffies);
 #endif
@@ -1512,6 +1517,7 @@ static void rp_hangup(struct tty_struct *tty)
 {
 	CHANNEL_t *cp;
 	struct r_port *info = tty->driver_data;
+	unsigned long flags;
 
 	if (rocket_paranoia_check(info, "rp_hangup"))
 		return;
@@ -1520,11 +1526,15 @@ static void rp_hangup(struct tty_struct *tty)
 	printk(KERN_INFO "rp_hangup of ttyR%d...\n", info->line);
 #endif
 	rp_flush_buffer(tty);
-	if (info->port.flags & ASYNC_CLOSING)
+	spin_lock_irqsave(&info->port.lock, flags);
+	if (info->port.flags & ASYNC_CLOSING) {
+		spin_unlock_irqrestore(&info->port.lock, flags);
 		return;
+	}
 	if (info->port.count)
 		atomic_dec(&rp_num_ports_open);
 	clear_bit((info->aiop * 8) + info->chan, (void *) &xmit_flags[info->board]);
+	spin_unlock_irqrestore(&info->port.lock, flags);
 
 	tty_port_hangup(&info->port);
 
@@ -1535,7 +1545,7 @@ static void rp_hangup(struct tty_struct *tty)
 	sDisCTSFlowCtl(cp);
 	sDisTxSoftFlowCtl(cp);
 	sClrTxXOFF(cp);
-	info->port.flags &= ~ASYNC_INITIALIZED;
+	clear_bit(ASYNCB_INITIALIZED, &info->port.flags);
 
 	wake_up_interruptible(&info->port.open_wait);
 }
Signature · 1 line
1.7.0.4
author maintainer
#6 lore raw

PATCH 6/31 synclink: kill the big kernel lock

In reply to Arnd Bergmann

From: Alan Cox <[email protected]>

We don't need it while waiting and we can lock the ioctls using the port mutex. While at it eliminate use of the hangup mutex and switch to the port mutex.

---
 drivers/char/synclink.c    |   19 ++++++-----
 drivers/char/synclink_gt.c |   78 +++++++++++++++++++-------------------------
 drivers/char/synclinkmp.c  |   32 +++++++-----------
 3 files changed, 56 insertions(+), 73 deletions(-)
drivers/char/synclink.c +10 -9
index 0658fc5..4de1246 100644
@@ -81,7 +81,6 @@
 #include <linux/mm.h>
 #include <linux/seq_file.h>
 #include <linux/slab.h>
-#include <linux/smp_lock.h>
 #include <linux/delay.h>
 #include <linux/netdevice.h>
 #include <linux/vmalloc.h>
@@ -2436,7 +2435,9 @@ static int mgsl_get_stats(struct mgsl_struct * info, struct mgsl_icount __user *
 	if (!user_icount) {
 		memset(&info->icount, 0, sizeof(info->icount));
 	} else {
+		mutex_lock(&info->port.mutex);
 		COPY_TO_USER(err, user_icount, &info->icount, sizeof(struct mgsl_icount));
+		mutex_unlock(&info->port.mutex);
 		if (err)
 			return -EFAULT;
 	}
@@ -2461,7 +2462,9 @@ static int mgsl_get_params(struct mgsl_struct * info, MGSL_PARAMS __user *user_p
 		printk("%s(%d):mgsl_get_params(%s)\n",
 			 __FILE__,__LINE__, info->device_name);
 			
+	mutex_lock(&info->port.mutex);
 	COPY_TO_USER(err,user_params, &info->params, sizeof(MGSL_PARAMS));
+	mutex_unlock(&info->port.mutex);
 	if (err) {
 		if ( debug_level >= DEBUG_LEVEL_INFO )
 			printk( "%s(%d):mgsl_get_params(%s) user buffer copy failed\n",
@@ -2501,11 +2504,13 @@ static int mgsl_set_params(struct mgsl_struct * info, MGSL_PARAMS __user *new_pa
 		return -EFAULT;
 	}
 	
+	mutex_lock(&info->port.mutex);
 	spin_lock_irqsave(&info->irq_spinlock,flags);
 	memcpy(&info->params,&tmp_params,sizeof(MGSL_PARAMS));
 	spin_unlock_irqrestore(&info->irq_spinlock,flags);
 	
  	mgsl_change_params(info);
+	mutex_unlock(&info->port.mutex);
 	
 	return 0;
 	
@@ -2935,7 +2940,6 @@ static int mgsl_ioctl(struct tty_struct *tty, struct file * file,
 		    unsigned int cmd, unsigned long arg)
 {
 	struct mgsl_struct * info = tty->driver_data;
-	int ret;
 	
 	if (debug_level >= DEBUG_LEVEL_INFO)
 		printk("%s(%d):mgsl_ioctl %s cmd=%08X\n", __FILE__,__LINE__,
@@ -2950,10 +2954,7 @@ static int mgsl_ioctl(struct tty_struct *tty, struct file * file,
 		    return -EIO;
 	}
 
-	lock_kernel();
-	ret = mgsl_ioctl_common(info, cmd, arg);
-	unlock_kernel();
-	return ret;
+	return mgsl_ioctl_common(info, cmd, arg);
 }
 
 static int mgsl_ioctl_common(struct mgsl_struct *info, unsigned int cmd, unsigned long arg)
@@ -3109,12 +3110,14 @@ static void mgsl_close(struct tty_struct *tty, struct file * filp)
 
 	if (tty_port_close_start(&info->port, tty, filp) == 0)			 
 		goto cleanup;
-			
+
+	mutex_lock(&info->port.mutex);			
  	if (info->port.flags & ASYNC_INITIALIZED)
  		mgsl_wait_until_sent(tty, info->timeout);
 	mgsl_flush_buffer(tty);
 	tty_ldisc_flush(tty);
 	shutdown(info);
+	mutex_unlock(&info->port.mutex);
 
 	tty_port_close_end(&info->port, tty);	
 	info->port.tty = NULL;
@@ -3162,7 +3165,6 @@ static void mgsl_wait_until_sent(struct tty_struct *tty, int timeout)
 	 * Note: use tight timings here to satisfy the NIST-PCTS.
 	 */ 
 
-	lock_kernel();
 	if ( info->params.data_rate ) {
 	       	char_time = info->timeout/(32 * 5);
 		if (!char_time)
@@ -3192,7 +3194,6 @@ static void mgsl_wait_until_sent(struct tty_struct *tty, int timeout)
 				break;
 		}
 	}
-	unlock_kernel();
       
 exit:
 	if (debug_level >= DEBUG_LEVEL_INFO)
drivers/char/synclink_gt.c +34 -44

123 lines not on this page · raw message

drivers/char/synclinkmp.c +12 -20
index 2b18adc..8da976b 100644
@@ -52,7 +52,6 @@
 #include <linux/mm.h>
 #include <linux/seq_file.h>
 #include <linux/slab.h>
-#include <linux/smp_lock.h>
 #include <linux/netdevice.h>
 #include <linux/vmalloc.h>
 #include <linux/init.h>
@@ -1062,9 +1061,7 @@ static void wait_until_sent(struct tty_struct *tty, int timeout)
 	if (sanity_check(info, tty->name, "wait_until_sent"))
 		return;
 
-	lock_kernel();
-
-	if (!(info->port.flags & ASYNC_INITIALIZED))
+	if (!test_bit(ASYNCB_INITIALIZED, &info->port.flags))
 		goto exit;
 
 	orig_jiffies = jiffies;
@@ -1094,8 +1091,10 @@ static void wait_until_sent(struct tty_struct *tty, int timeout)
 				break;
 		}
 	} else {
-		//TODO: determine if there is something similar to USC16C32
-		// 	TXSTATUS_ALL_SENT status
+		/*
+		 * TODO: determine if there is something similar to USC16C32
+		 * 	 TXSTATUS_ALL_SENT status
+		 */
 		while ( info->tx_active && info->tx_enabled) {
 			msleep_interruptible(jiffies_to_msecs(char_time));
 			if (signal_pending(current))
@@ -1106,7 +1105,6 @@ static void wait_until_sent(struct tty_struct *tty, int timeout)
 	}
 
 exit:
-	unlock_kernel();
 	if (debug_level >= DEBUG_LEVEL_INFO)
 		printk("%s(%d):%s wait_until_sent() exit\n",
 			 __FILE__,__LINE__, info->device_name );
@@ -1122,7 +1120,6 @@ static int write_room(struct tty_struct *tty)
 	if (sanity_check(info, tty->name, "write_room"))
 		return 0;
 
-	lock_kernel();
 	if (info->params.mode == MGSL_MODE_HDLC) {
 		ret = (info->tx_active) ? 0 : HDLC_MAX_FRAME_SIZE;
 	} else {
@@ -1130,7 +1127,6 @@ static int write_room(struct tty_struct *tty)
 		if (ret < 0)
 			ret = 0;
 	}
-	unlock_kernel();
 
 	if (debug_level >= DEBUG_LEVEL_INFO)
 		printk("%s(%d):%s write_room()=%d\n",
@@ -1251,7 +1247,7 @@ static void tx_release(struct tty_struct *tty)
  *
  * Return Value:	0 if success, otherwise error code
  */
-static int do_ioctl(struct tty_struct *tty, struct file *file,
+static int ioctl(struct tty_struct *tty, struct file *file,
 		 unsigned int cmd, unsigned long arg)
 {
 	SLMP_INFO *info = tty->driver_data;
@@ -1341,16 +1337,6 @@ static int do_ioctl(struct tty_struct *tty, struct file *file,
 	return 0;
 }
 
-static int ioctl(struct tty_struct *tty, struct file *file,
-		 unsigned int cmd, unsigned long arg)
-{
-	int ret;
-	lock_kernel();
-	ret = do_ioctl(tty, file, cmd, arg);
-	unlock_kernel();
-	return ret;
-}
-
 /*
  * /proc fs routines....
  */
@@ -2883,7 +2869,9 @@ static int get_stats(SLMP_INFO * info, struct mgsl_icount __user *user_icount)
 	if (!user_icount) {
 		memset(&info->icount, 0, sizeof(info->icount));
 	} else {
+		mutex_lock(&info->port.mutex);
 		COPY_TO_USER(err, user_icount, &info->icount, sizeof(struct mgsl_icount));
+		mutex_unlock(&info->port.mutex);
 		if (err)
 			return -EFAULT;
 	}
@@ -2898,7 +2886,9 @@ static int get_params(SLMP_INFO * info, MGSL_PARAMS __user *user_params)
 		printk("%s(%d):%s get_params()\n",
 			 __FILE__,__LINE__, info->device_name);
 
+	mutex_lock(&info->port.mutex);
 	COPY_TO_USER(err,user_params, &info->params, sizeof(MGSL_PARAMS));
+	mutex_unlock(&info->port.mutex);
 	if (err) {
 		if ( debug_level >= DEBUG_LEVEL_INFO )
 			printk( "%s(%d):%s get_params() user buffer copy failed\n",
@@ -2926,11 +2916,13 @@ static int set_params(SLMP_INFO * info, MGSL_PARAMS __user *new_params)
 		return -EFAULT;
 	}
 
+	mutex_lock(&info->port.mutex);
 	spin_lock_irqsave(&info->lock,flags);
 	memcpy(&info->params,&tmp_params,sizeof(MGSL_PARAMS));
 	spin_unlock_irqrestore(&info->lock,flags);
 
  	change_params(info);
+	mutex_unlock(&info->port.mutex);
 
 	return 0;
 }
Signature · 1 line
1.7.0.4
author maintainer
#7 lore raw

PATCH 7/31 cyclades: Kill off BKL usage

In reply to Arnd Bergmann

From: Alan Cox <[email protected]>

Use the port mutext for config setting, the rest is locked sufficiently anyway that the BKL makes no odds.

---
 drivers/char/cyclades.c |   20 +++++++++-----------
 1 files changed, 9 insertions(+), 11 deletions(-)
drivers/char/cyclades.c +9 -11
index 9824b41..51acfe3 100644
@@ -65,7 +65,6 @@
 #include <linux/tty.h>
 #include <linux/tty_flip.h>
 #include <linux/serial.h>
-#include <linux/smp_lock.h>
 #include <linux/major.h>
 #include <linux/string.h>
 #include <linux/fcntl.h>
@@ -1655,7 +1654,6 @@ static void cy_wait_until_sent(struct tty_struct *tty, int timeout)
 		return;		/* Just in case.... */
 
 	orig_jiffies = jiffies;
-	lock_kernel();
 	/*
 	 * Set the check interval to be 1/5 of the estimated time to
 	 * send a single character, and make it at least 1.  The check
@@ -1702,7 +1700,6 @@ static void cy_wait_until_sent(struct tty_struct *tty, int timeout)
 	}
 	/* Run one more char cycle */
 	msleep_interruptible(jiffies_to_msecs(char_time * 5));
-	unlock_kernel();
 #ifdef CY_DEBUG_WAIT_UNTIL_SENT
 	printk(KERN_DEBUG "Clean (jiff=%lu)...done\n", jiffies);
 #endif
@@ -1959,7 +1956,6 @@ static int cy_chars_in_buffer(struct tty_struct *tty)
 		int char_count;
 		__u32 tx_put, tx_get, tx_bufsize;
 
-		lock_kernel();
 		tx_get = readl(&buf_ctrl->tx_get);
 		tx_put = readl(&buf_ctrl->tx_put);
 		tx_bufsize = readl(&buf_ctrl->tx_bufsize);
@@ -1971,7 +1967,6 @@ static int cy_chars_in_buffer(struct tty_struct *tty)
 		printk(KERN_DEBUG "cyc:cy_chars_in_buffer ttyC%d %d\n",
 			info->line, info->xmit_cnt + char_count);
 #endif
-		unlock_kernel();
 		return info->xmit_cnt + char_count;
 	}
 #endif				/* Z_EXT_CHARS_IN_BUFFER */
@@ -2359,17 +2354,22 @@ cy_set_serial_info(struct cyclades_port *info, struct tty_struct *tty,
 		struct serial_struct __user *new_info)
 {
 	struct serial_struct new_serial;
+	int ret;
 
 	if (copy_from_user(&new_serial, new_info, sizeof(new_serial)))
 		return -EFAULT;
 
+	mutex_lock(&info->port.mutex);
 	if (!capable(CAP_SYS_ADMIN)) {
 		if (new_serial.close_delay != info->port.close_delay ||
 				new_serial.baud_base != info->baud ||
 				(new_serial.flags & ASYNC_FLAGS &
 					~ASYNC_USR_MASK) !=
 				(info->port.flags & ASYNC_FLAGS & ~ASYNC_USR_MASK))
+		{
+			mutex_unlock(&info->port.mutex);
 			return -EPERM;
+		}
 		info->port.flags = (info->port.flags & ~ASYNC_USR_MASK) |
 				(new_serial.flags & ASYNC_USR_MASK);
 		info->baud = new_serial.baud_base;
@@ -2392,10 +2392,12 @@ cy_set_serial_info(struct cyclades_port *info, struct tty_struct *tty,
 check_and_exit:
 	if (info->port.flags & ASYNC_INITIALIZED) {
 		cy_set_line_char(info, tty);
-		return 0;
+		ret = 0;
 	} else {
-		return cy_startup(info, tty);
+		ret = cy_startup(info, tty);
 	}
+	mutex_unlock(&info->port.mutex);
+	return ret;
 }				/* set_serial_info */
 
 /*
@@ -2438,7 +2440,6 @@ static int cy_tiocmget(struct tty_struct *tty, struct file *file)
 
 	card = info->card;
 
-	lock_kernel();
 	if (!cy_is_Z(card)) {
 		unsigned long flags;
 		int channel = info->line - card->first_line;
@@ -2478,7 +2479,6 @@ static int cy_tiocmget(struct tty_struct *tty, struct file *file)
 			((lstatus & C_RS_CTS) ? TIOCM_CTS : 0);
 	}
 end:
-	unlock_kernel();
 	return result;
 }				/* cy_tiomget */
 
@@ -2696,7 +2696,6 @@ cy_ioctl(struct tty_struct *tty, struct file *file,
 	printk(KERN_DEBUG "cyc:cy_ioctl ttyC%d, cmd = %x arg = %lx\n",
 		info->line, cmd, arg);
 #endif
-	lock_kernel();
 
 	switch (cmd) {
 	case CYGETMON:
@@ -2817,7 +2816,6 @@ cy_ioctl(struct tty_struct *tty, struct file *file,
 	default:
 		ret_val = -ENOIOCTLCMD;
 	}
-	unlock_kernel();
 
 #ifdef CY_DEBUG_OTHER
 	printk(KERN_DEBUG "cyc:cy_ioctl done\n");
Signature · 1 line
1.7.0.4
author maintainer
#8 lore raw

PATCH 8/31 epca: Kill the big kernel lock

In reply to Arnd Bergmann

From: Alan Cox <[email protected]>

The lock is no longer needed for wait until sent paths so this can go

---
 drivers/char/epca.c |    4 +---
 1 files changed, 1 insertions(+), 3 deletions(-)
drivers/char/epca.c +1 -3
index 6f5ffe1..d9df46a 100644
@@ -36,7 +36,7 @@
 #include <linux/ctype.h>
 #include <linux/tty.h>
 #include <linux/tty_flip.h>
-#include <linux/smp_lock.h>
+#include <linux/slab.h>
 #include <linux/ioport.h>
 #include <linux/interrupt.h>
 #include <linux/uaccess.h>
@@ -2105,7 +2105,6 @@ static int pc_ioctl(struct tty_struct *tty, struct file *file,
 		break;
 	case DIGI_SETAW:
 	case DIGI_SETAF:
-		lock_kernel();
 		if (cmd == DIGI_SETAW) {
 			/* Setup an event to indicate when the transmit
 			   buffer empties */
@@ -2118,7 +2117,6 @@ static int pc_ioctl(struct tty_struct *tty, struct file *file,
 			if (tty->ldisc->ops->flush_buffer)
 				tty->ldisc->ops->flush_buffer(tty);
 		}
-		unlock_kernel();
 		/* Fall Thru */
 	case DIGI_SETA:
 		if (copy_from_user(&ch->digiext, argp, sizeof(digi_t)))
Signature · 1 line
1.7.0.4
author maintainer
#9 lore raw

PATCH 9/31 specialix; Kill the BKL

In reply to Arnd Bergmann

From: Alan Cox <[email protected]>

Use the port mutex instead

---
 drivers/char/specialix.c |   11 +++++------
 1 files changed, 5 insertions(+), 6 deletions(-)
drivers/char/specialix.c +5 -6
index 2c24fcd..7be456f 100644
@@ -1863,8 +1863,7 @@ static int sx_set_serial_info(struct specialix_port *port,
 		return -EFAULT;
 	}
 
-	lock_kernel();
-
+	mutex_lock(&port->port.mutex);
 	change_speed = ((port->port.flags & ASYNC_SPD_MASK) !=
 			(tmp.flags & ASYNC_SPD_MASK));
 	change_speed |= (tmp.custom_divisor != port->custom_divisor);
@@ -1875,7 +1874,7 @@ static int sx_set_serial_info(struct specialix_port *port,
 		    ((tmp.flags & ~ASYNC_USR_MASK) !=
 		     (port->port.flags & ~ASYNC_USR_MASK))) {
 			func_exit();
-			unlock_kernel();
+			mutex_unlock(&port->port.mutex);
 			return -EPERM;
 		}
 		port->port.flags = ((port->port.flags & ~ASYNC_USR_MASK) |
@@ -1892,7 +1891,7 @@ static int sx_set_serial_info(struct specialix_port *port,
 		sx_change_speed(bp, port);
 
 	func_exit();
-	unlock_kernel();
+	mutex_unlock(&port->port.mutex);
 	return 0;
 }
 
@@ -1906,7 +1905,7 @@ static int sx_get_serial_info(struct specialix_port *port,
 	func_enter();
 
 	memset(&tmp, 0, sizeof(tmp));
-	lock_kernel();
+	mutex_lock(&port->port.mutex);
 	tmp.type = PORT_CIRRUS;
 	tmp.line = port - sx_port;
 	tmp.port = bp->base;
@@ -1917,7 +1916,7 @@ static int sx_get_serial_info(struct specialix_port *port,
 	tmp.closing_wait = port->port.closing_wait * HZ/100;
 	tmp.custom_divisor =  port->custom_divisor;
 	tmp.xmit_fifo_size = CD186x_NFIFO;
-	unlock_kernel();
+	mutex_unlock(&port->port.mutex);
 	if (copy_to_user(retinfo, &tmp, sizeof(tmp))) {
 		func_exit();
 		return -EFAULT;
Signature · 1 line
1.7.0.4
author maintainer
#10 lore raw

PATCH 10/31 synclink: reworking locking a bit

In reply to Arnd Bergmann

From: Alan Cox <[email protected]>

Use the port mutex and port lock to fix the various races. The locking still isn't totally consistent but its better than before. Wants switching to the port helpers.

---
 drivers/char/synclink_gt.c |   12 +++++++++++-
 drivers/char/synclinkmp.c  |    9 ++++++++-
 2 files changed, 19 insertions(+), 2 deletions(-)
drivers/char/synclink_gt.c +11 -1
index d0f81f5..c56b70a 100644
@@ -675,12 +675,14 @@ static int open(struct tty_struct *tty, struct file *filp)
 		goto cleanup;
 	}
 
+	mutex_lock(&info->port.mutex);
 	info->port.tty->low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
 
 	spin_lock_irqsave(&info->netlock, flags);
 	if (info->netcount) {
 		retval = -EBUSY;
 		spin_unlock_irqrestore(&info->netlock, flags);
+		mutex_unlock(&info->port.mutex);
 		goto cleanup;
 	}
 	info->port.count++;
@@ -692,7 +694,7 @@ static int open(struct tty_struct *tty, struct file *filp)
 		if (retval < 0)
 			goto cleanup;
 	}
-
+	mutex_unlock(&info->port.mutex);
 	retval = block_til_ready(tty, filp, info);
 	if (retval) {
 		DBGINFO(("%s block_til_ready rc=%d\n", info->device_name, retval));
@@ -724,12 +726,14 @@ static void close(struct tty_struct *tty, struct file *filp)
 	if (tty_port_close_start(&info->port, tty, filp) == 0)
 		goto cleanup;
 
+	mutex_lock(&info->port.mutex);
  	if (info->port.flags & ASYNC_INITIALIZED)
  		wait_until_sent(tty, info->timeout);
 	flush_buffer(tty);
 	tty_ldisc_flush(tty);
 
 	shutdown(info);
+	mutex_unlock(&info->port.mutex);
 
 	tty_port_close_end(&info->port, tty);
 	info->port.tty = NULL;
@@ -740,17 +744,23 @@ cleanup:
 static void hangup(struct tty_struct *tty)
 {
 	struct slgt_info *info = tty->driver_data;
+	unsigned long flags;
 
 	if (sanity_check(info, tty->name, "hangup"))
 		return;
 	DBGINFO(("%s hangup\n", info->device_name));
 
 	flush_buffer(tty);
+
+	mutex_lock(&info->port.mutex);
 	shutdown(info);
 
+	spin_lock_irqsave(&info->port.lock, flags);
 	info->port.count = 0;
 	info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
 	info->port.tty = NULL;
+	spin_unlock_irqrestore(&info->port.lock, flags);
+	mutex_unlock(&info->port.mutex);
 
 	wake_up_interruptible(&info->port.open_wait);
 }
drivers/char/synclinkmp.c +8 -1
index 8da976b..cfa581e 100644
@@ -812,13 +812,15 @@ static void close(struct tty_struct *tty, struct file *filp)
 
 	if (tty_port_close_start(&info->port, tty, filp) == 0)
 		goto cleanup;
-		
+
+	mutex_lock(&info->port.mutex);		
  	if (info->port.flags & ASYNC_INITIALIZED)
  		wait_until_sent(tty, info->timeout);
 
 	flush_buffer(tty);
 	tty_ldisc_flush(tty);
 	shutdown(info);
+	mutex_unlock(&info->port.mutex);		
 
 	tty_port_close_end(&info->port, tty);
 	info->port.tty = NULL;
@@ -834,6 +836,7 @@ cleanup:
 static void hangup(struct tty_struct *tty)
 {
 	SLMP_INFO *info = tty->driver_data;
+	unsigned long flags;
 
 	if (debug_level >= DEBUG_LEVEL_INFO)
 		printk("%s(%d):%s hangup()\n",
@@ -842,12 +845,16 @@ static void hangup(struct tty_struct *tty)
 	if (sanity_check(info, tty->name, "hangup"))
 		return;
 
+	mutex_lock(&info->port.mutex);		
 	flush_buffer(tty);
 	shutdown(info);
 
+	spin_lock_irqsave(&info->port.lock, flags);
 	info->port.count = 0;
 	info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
 	info->port.tty = NULL;
+	spin_unlock_irqrestore(&info->port.lock, flags);
+	mutex_unlock(&info->port.mutex);		
 
 	wake_up_interruptible(&info->port.open_wait);
 }
Signature · 1 line
1.7.0.4
author maintainer
#11 lore raw

PATCH 11/31 tty: serial - fix various misuses/mishandlings of port->tty

In reply to Arnd Bergmann

From: Alan Cox <[email protected]>

Make it robust against hang up events. In most cases we can do this simply by passing the right things in the first place.

---
 drivers/serial/serial_core.c |  109 +++++++++++++++++++++++-------------------
 1 files changed, 60 insertions(+), 49 deletions(-)
drivers/serial/serial_core.c +60 -49
index 7f28307..12ee7e0 100644
@@ -58,7 +58,7 @@ static struct lock_class_key port_lock_key;
 #define uart_console(port)	(0)
 #endif
 
-static void uart_change_speed(struct uart_state *state,
+static void uart_change_speed(struct tty_struct *tty, struct uart_state *state,
 					struct ktermios *old_termios);
 static void uart_wait_until_sent(struct tty_struct *tty, int timeout);
 static void uart_change_pm(struct uart_state *state, int pm_state);
@@ -137,7 +137,7 @@ uart_update_mctrl(struct uart_port *port, unsigned int set, unsigned int clear)
  * Startup the port.  This will be called once per open.  All calls
  * will be serialised by the per-port mutex.
  */
-static int uart_startup(struct uart_state *state, int init_hw)
+static int uart_startup(struct tty_struct *tty, struct uart_state *state, int init_hw)
 {
 	struct uart_port *uport = state->uart_port;
 	struct tty_port *port = &state->port;
@@ -152,7 +152,7 @@ static int uart_startup(struct uart_state *state, int init_hw)
 	 * once we have successfully opened the port.  Also set
 	 * up the tty->alt_speed kludge
 	 */
-	set_bit(TTY_IO_ERROR, &port->tty->flags);
+	set_bit(TTY_IO_ERROR, &tty->flags);
 
 	if (uport->type == PORT_UNKNOWN)
 		return 0;
@@ -177,26 +177,26 @@ static int uart_startup(struct uart_state *state, int init_hw)
 			/*
 			 * Initialise the hardware port settings.
 			 */
-			uart_change_speed(state, NULL);
+			uart_change_speed(tty, state, NULL);
 
 			/*
 			 * Setup the RTS and DTR signals once the
 			 * port is open and ready to respond.
 			 */
-			if (port->tty->termios->c_cflag & CBAUD)
+			if (tty->termios->c_cflag & CBAUD)
 				uart_set_mctrl(uport, TIOCM_RTS | TIOCM_DTR);
 		}
 
 		if (port->flags & ASYNC_CTS_FLOW) {
 			spin_lock_irq(&uport->lock);
 			if (!(uport->ops->get_mctrl(uport) & TIOCM_CTS))
-				port->tty->hw_stopped = 1;
+				tty->hw_stopped = 1;
 			spin_unlock_irq(&uport->lock);
 		}
 
 		set_bit(ASYNCB_INITIALIZED, &port->flags);
 
-		clear_bit(TTY_IO_ERROR, &port->tty->flags);
+		clear_bit(TTY_IO_ERROR, &tty->flags);
 	}
 
 	if (retval && capable(CAP_SYS_ADMIN))
@@ -210,11 +210,10 @@ static int uart_startup(struct uart_state *state, int init_hw)
  * DTR is dropped if the hangup on close termio flag is on.  Calls to
  * uart_shutdown are serialised by the per-port semaphore.
  */
-static void uart_shutdown(struct uart_state *state)
+static void uart_shutdown(struct tty_struct *tty, struct uart_state *state)
 {
 	struct uart_port *uport = state->uart_port;
 	struct tty_port *port = &state->port;
-	struct tty_struct *tty = port->tty;
 
 	/*
 	 * Set the TTY IO error marker
@@ -430,11 +429,10 @@ uart_get_divisor(struct uart_port *port, unsigned int baud)
 EXPORT_SYMBOL(uart_get_divisor);
 
 /* FIXME: Consistent locking policy */
-static void
-uart_change_speed(struct uart_state *state, struct ktermios *old_termios)
+static void uart_change_speed(struct tty_struct *tty, struct uart_state *state,
+					struct ktermios *old_termios)
 {
 	struct tty_port *port = &state->port;
-	struct tty_struct *tty = port->tty;
 	struct uart_port *uport = state->uart_port;
 	struct ktermios *termios;
 
@@ -463,8 +461,8 @@ uart_change_speed(struct uart_state *state, struct ktermios *old_termios)
 	uport->ops->set_termios(uport, termios, old_termios);
 }
 
-static inline int
-__uart_put_char(struct uart_port *port, struct circ_buf *circ, unsigned char c)
+static inline int __uart_put_char(struct uart_port *port,
+				struct circ_buf *circ, unsigned char c)
 {
 	unsigned long flags;
 	int ret = 0;
@@ -494,8 +492,8 @@ static void uart_flush_chars(struct tty_struct *tty)
 	uart_start(tty);
 }
 
-static int
-uart_write(struct tty_struct *tty, const unsigned char *buf, int count)
+static int uart_write(struct tty_struct *tty,
+					const unsigned char *buf, int count)
 {
 	struct uart_state *state = tty->driver_data;
 	struct uart_port *port;
@@ -675,7 +673,7 @@ static int uart_get_info(struct uart_state *state,
 	return 0;
 }
 
-static int uart_set_info(struct uart_state *state,
+static int uart_set_info(struct tty_struct *tty, struct uart_state *state,
 			 struct serial_struct __user *newinfo)
 {
 	struct serial_struct new_serial;
@@ -770,7 +768,7 @@ static int uart_set_info(struct uart_state *state,
 		 * We need to shutdown the serial port at the old
 		 * port/type/irq combination.
 		 */
-		uart_shutdown(state);
+		uart_shutdown(tty, state);
 	}
 
 	if (change_port) {
@@ -869,25 +867,27 @@ static int uart_set_info(struct uart_state *state,
 				       "is deprecated.\n", current->comm,
 				       tty_name(port->tty, buf));
 			}
-			uart_change_speed(state, NULL);
+			uart_change_speed(tty, state, NULL);
 		}
 	} else
-		retval = uart_startup(state, 1);
+		retval = uart_startup(tty, state, 1);
  exit:
 	mutex_unlock(&port->mutex);
 	return retval;
 }
 
-
-/*
- * uart_get_lsr_info - get line status register info.
- * Note: uart_ioctl protects us against hangups.
+/**
+ *	uart_get_lsr_info	-	get line status register info
+ *	@tty: tty associated with the UART
+ *	@state: UART being queried
+ *	@value: returned modem value
+ *
+ *	Note: uart_ioctl protects us against hangups.
  */
-static int uart_get_lsr_info(struct uart_state *state,
-			     unsigned int __user *value)
+static int uart_get_lsr_info(struct tty_struct *tty,
+			struct uart_state *state, unsigned int __user *value)
 {
 	struct uart_port *uport = state->uart_port;
-	struct tty_port *port = &state->port;
 	unsigned int result;
 
 	result = uport->ops->tx_empty(uport);
@@ -900,7 +900,7 @@ static int uart_get_lsr_info(struct uart_state *state,
 	 */
 	if (uport->x_char ||
 	    ((uart_circ_chars_pending(&state->xmit) > 0) &&
-	     !port->tty->stopped && !port->tty->hw_stopped))
+	     !tty->stopped && !tty->hw_stopped))
 		result &= ~TIOCSER_TEMT;
 
 	return put_user(result, value);
@@ -961,7 +961,7 @@ static int uart_break_ctl(struct tty_struct *tty, int break_state)
 	return 0;
 }
 
-static int uart_do_autoconfig(struct uart_state *state)
+static int uart_do_autoconfig(struct tty_struct *tty,struct uart_state *state)
 {
 	struct uart_port *uport = state->uart_port;
 	struct tty_port *port = &state->port;
@@ -980,7 +980,7 @@ static int uart_do_autoconfig(struct uart_state *state)
 
 	ret = -EBUSY;
 	if (tty_port_users(port) == 1) {
-		uart_shutdown(state);
+		uart_shutdown(tty, state);
 
 		/*
 		 * If we already have a port type configured,
@@ -999,7 +999,7 @@ static int uart_do_autoconfig(struct uart_state *state)
 		 */
 		uport->ops->config_port(uport, flags);
 
-		ret = uart_startup(state, 1);
+		ret = uart_startup(tty, state, 1);
 	}
 	mutex_unlock(&port->mutex);
 	return ret;
@@ -1122,11 +1122,11 @@ uart_ioctl(struct tty_struct *tty, struct file *filp, unsigned int cmd,
 		break;
 
 	case TIOCSSERIAL:
-		ret = uart_set_info(state, uarg);
+		ret = uart_set_info(tty, state, uarg);
 		break;
 
 	case TIOCSERCONFIG:
-		ret = uart_do_autoconfig(state);
+		ret = uart_do_autoconfig(tty, state);
 		break;
 
 	case TIOCSERGWILD: /* obsolete */
@@ -1172,7 +1172,7 @@ uart_ioctl(struct tty_struct *tty, struct file *filp, unsigned int cmd,
 	 */
 	switch (cmd) {
 	case TIOCSERGETLSR: /* Get line status register */
-		ret = uart_get_lsr_info(state, uarg);
+		ret = uart_get_lsr_info(tty, state, uarg);
 		break;
 
 	default: {
@@ -1219,7 +1219,7 @@ static void uart_set_termios(struct tty_struct *tty,
 		return;
 	}
 
-	uart_change_speed(state, old_termios);
+	uart_change_speed(tty, state, old_termios);
 
 	/* Handle transition to B0 status */
 	if ((old_termios->c_cflag & CBAUD) && !(cflag & CBAUD))
@@ -1335,7 +1335,7 @@ static void uart_close(struct tty_struct *tty, struct file *filp)
 		uart_wait_until_sent(tty, uport->timeout);
 	}
 
-	uart_shutdown(state);
+	uart_shutdown(tty, state);
 	uart_flush_buffer(tty);
 
 	tty_ldisc_flush(tty);
@@ -1436,7 +1436,7 @@ static void uart_hangup(struct tty_struct *tty)
 	mutex_lock(&port->mutex);
 	if (port->flags & ASYNC_NORMAL_ACTIVE) {
 		uart_flush_buffer(tty);
-		uart_shutdown(state);
+		uart_shutdown(tty, state);
 		port->count = 0;
 		clear_bit(ASYNCB_NORMAL_ACTIVE, &port->flags);
 		tty_port_tty_set(port, NULL);
@@ -1446,15 +1446,19 @@ static void uart_hangup(struct tty_struct *tty)
 	mutex_unlock(&port->mutex);
 }
 
-/*
- * Copy across the serial console cflag setting into the termios settings
- * for the initial open of the port.  This allows continuity between the
- * kernel settings, and the settings init adopts when it opens the port
- * for the first time.
+/**
+ *	uart_update_termios	-	update the terminal hw settings
+ *	@tty: tty associated with UART
+ *	@state: UART to update
+ *
+ *	Copy across the serial console cflag setting into the termios settings
+ *	for the initial open of the port.  This allows continuity between the
+ *	kernel settings, and the settings init adopts when it opens the port
+ *	for the first time.
  */
-static void uart_update_termios(struct uart_state *state)
+static void uart_update_termios(struct tty_struct *tty,
+						struct uart_state *state)
 {
-	struct tty_struct *tty = state->port.tty;
 	struct uart_port *port = state->uart_port;
 
 	if (uart_console(port) && port->cons->cflag) {
@@ -1471,7 +1475,7 @@ static void uart_update_termios(struct uart_state *state)
 		/*
 		 * Make termios settings take effect.
 		 */
-		uart_change_speed(state, NULL);
+		uart_change_speed(tty, state, NULL);
 
 		/*
 		 * And finally enable the RTS and DTR signals.
@@ -1668,7 +1672,7 @@ static int uart_open(struct tty_struct *tty, struct file *filp)
 	/*
 	 * Start up the serial port.
 	 */
-	retval = uart_startup(state, 0);
+	retval = uart_startup(tty, state, 0);
 
 	/*
 	 * If we succeeded, wait until the port is ready.
@@ -1683,7 +1687,7 @@ static int uart_open(struct tty_struct *tty, struct file *filp)
 	if (retval == 0 && !(port->flags & ASYNC_NORMAL_ACTIVE)) {
 		set_bit(ASYNCB_NORMAL_ACTIVE, &port->flags);
 
-		uart_update_termios(state);
+		uart_update_termios(tty, state);
 	}
 
 fail:
@@ -2010,9 +2014,13 @@ int uart_suspend_port(struct uart_driver *drv, struct uart_port *uport)
 	struct tty_port *port = &state->port;
 	struct device *tty_dev;
 	struct uart_match match = {uport, drv};
+	struct tty_struct *tty;
 
 	mutex_lock(&port->mutex);
 
+	/* Must be inside the mutex lock until we convert to tty_port */
+	tty = port->tty;
+
 	tty_dev = device_find_child(uport->dev, &match, serial_match_port);
 	if (device_may_wakeup(tty_dev)) {
 		enable_irq_wake(uport->irq);
@@ -2105,9 +2113,12 @@ int uart_resume_port(struct uart_driver *drv, struct uart_port *uport)
 		ops->set_mctrl(uport, 0);
 		spin_unlock_irq(&uport->lock);
 		if (console_suspend_enabled || !uart_console(uport)) {
+			/* Protected by port mutex for now */
+			struct tty_struct *tty = port->tty;
 			ret = ops->startup(uport);
 			if (ret == 0) {
-				uart_change_speed(state, NULL);
+				if (tty)
+					uart_change_speed(tty, state, NULL);
 				spin_lock_irq(&uport->lock);
 				ops->set_mctrl(uport, uport->mctrl);
 				ops->start_tx(uport);
@@ -2119,7 +2130,7 @@ int uart_resume_port(struct uart_driver *drv, struct uart_port *uport)
 				 * Clear the "initialized" flag so we won't try
 				 * to call the low level drivers shutdown method.
 				 */
-				uart_shutdown(state);
+				uart_shutdown(tty, state);
 			}
 		}
 
Signature · 1 line
1.7.0.4
author maintainer
#12 lore raw

PATCH 12/31 tty: serial - fix tty back references in termios

In reply to Arnd Bergmann

From: Alan Cox <[email protected]>

One or two drivers go poking back into the tty from the termios setting routine in unsafe ways. We don't need to pass the tty down because the [ab]users are just using it to get at things they can get at anyway.

This leaves low_latency setting to sort out along with set_ldisc use.

---
 drivers/serial/21285.c       |   10 +++-------
 drivers/serial/imx.c         |   10 ++++------
 drivers/serial/ioc3_serial.c |    9 +++++----
 drivers/serial/ioc4_serial.c |    9 +++++----
 drivers/serial/max3100.c     |    7 ++-----
 5 files changed, 19 insertions(+), 26 deletions(-)
drivers/serial/21285.c +3 -7
index 8681f13..d89aa38 100644
@@ -216,7 +216,7 @@ serial21285_set_termios(struct uart_port *port, struct ktermios *termios,
 			struct ktermios *old)
 {
 	unsigned long flags;
-	unsigned int baud, quot, h_lcr;
+	unsigned int baud, quot, h_lcr, b;
 
 	/*
 	 * We don't support modem control lines.
@@ -234,12 +234,8 @@ serial21285_set_termios(struct uart_port *port, struct ktermios *termios,
 	 */
 	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); 
 	quot = uart_get_divisor(port, baud);
-
-	if (port->state && port->state->port.tty) {
-		struct tty_struct *tty = port->state->port.tty;
-		unsigned int b = port->uartclk / (16 * quot);
-		tty_encode_baud_rate(tty, b, b);
-	}
+	b = port->uartclk / (16 * quot);
+	tty_termios_encode_baud_rate(termios, b, b);
 
 	switch (termios->c_cflag & CSIZE) {
 	case CS5:
drivers/serial/imx.c +4 -6
index eacb588..66ecc7a 100644
@@ -909,13 +909,11 @@ imx_set_termios(struct uart_port *port, struct ktermios *termios,
 	rational_best_approximation(16 * div * baud, sport->port.uartclk,
 		1 << 16, 1 << 16, &num, &denom);
 
-	if (port->state && port->state->port.tty) {
-		tdiv64 = sport->port.uartclk;
-		tdiv64 *= num;
-		do_div(tdiv64, denom * 16 * div);
-		tty_encode_baud_rate(sport->port.state->port.tty,
+	tdiv64 = sport->port.uartclk;
+	tdiv64 *= num;
+	do_div(tdiv64, denom * 16 * div);
+	tty_termios_encode_baud_rate(termios,
 				(speed_t)tdiv64, (speed_t)tdiv64);
-	}
 
 	num -= 1;
 	denom -= 1;
drivers/serial/ioc3_serial.c +5 -4
index f164ba4..bd2e9e6 100644
@@ -954,12 +954,13 @@ ioc3_change_speed(struct uart_port *the_port,
 		  struct ktermios *new_termios, struct ktermios *old_termios)
 {
 	struct ioc3_port *port = get_ioc3_port(the_port);
-	unsigned int cflag;
+	unsigned int cflag, iflag;
 	int baud;
 	int new_parity = 0, new_parity_enable = 0, new_stop = 0, new_data = 8;
 	struct uart_state *state = the_port->state;
 
 	cflag = new_termios->c_cflag;
+	iflag = new_termios->c_iflag;
 
 	switch (cflag & CSIZE) {
 	case CS5:
@@ -1000,12 +1001,12 @@ ioc3_change_speed(struct uart_port *the_port,
 
 	state->port.tty->low_latency = 1;
 
-	if (I_IGNPAR(state->port.tty))
+	if (iflag & IGNPAR))
 		the_port->ignore_status_mask &= ~(N_PARITY_ERROR
 						  | N_FRAMING_ERROR);
-	if (I_IGNBRK(state->port.tty)) {
+	if (iflag & IGNBRK) {
 		the_port->ignore_status_mask &= ~N_BREAK;
-		if (I_IGNPAR(state->port.tty))
+		if (iflag & IGNPAR)
 			the_port->ignore_status_mask &= ~N_OVERRUN_ERROR;
 	}
 	if (!(cflag & CREAD)) {
drivers/serial/ioc4_serial.c +5 -4
index 8ad28fc..2c30023 100644
@@ -1685,11 +1685,12 @@ ioc4_change_speed(struct uart_port *the_port,
 {
 	struct ioc4_port *port = get_ioc4_port(the_port, 0);
 	int baud, bits;
-	unsigned cflag;
+	unsigned cflag, iflag;
 	int new_parity = 0, new_parity_enable = 0, new_stop = 0, new_data = 8;
 	struct uart_state *state = the_port->state;
 
 	cflag = new_termios->c_cflag;
+	iflag = new_termios->c_iflag;
 
 	switch (cflag & CSIZE) {
 	case CS5:
@@ -1741,12 +1742,12 @@ ioc4_change_speed(struct uart_port *the_port,
 
 	state->port.tty->low_latency = 1;
 
-	if (I_IGNPAR(state->port.tty))
+	if (iflag & IGNPAR)
 		the_port->ignore_status_mask &= ~(N_PARITY_ERROR
 						| N_FRAMING_ERROR);
-	if (I_IGNBRK(state->port.tty)) {
+	if (iflag & IGNBRK) {
 		the_port->ignore_status_mask &= ~N_BREAK;
-		if (I_IGNPAR(state->port.tty))
+		if (iflag & IGNPAR))
 			the_port->ignore_status_mask &= ~N_OVERRUN_ERROR;
 	}
 	if (!(cflag & CREAD)) {
drivers/serial/max3100.c +2 -5
index 3351c3b..beb1afa 100644
@@ -430,17 +430,14 @@ max3100_set_termios(struct uart_port *port, struct ktermios *termios,
 	int baud = 0;
 	unsigned cflag;
 	u32 param_new, param_mask, parity = 0;
-	struct tty_struct *tty = s->port.state->port.tty;
 
 	dev_dbg(&s->spi->dev, "%s\n", __func__);
-	if (!tty)
-		return;
 
 	cflag = termios->c_cflag;
 	param_new = 0;
 	param_mask = 0;
 
-	baud = tty_get_baud_rate(tty);
+	baud = tty_termios_baud_rate(termios);
 	param_new = s->conf & MAX3100_BAUD;
 	switch (baud) {
 	case 300:
@@ -485,7 +482,7 @@ max3100_set_termios(struct uart_port *port, struct ktermios *termios,
 	default:
 		baud = s->baud;
 	}
-	tty_encode_baud_rate(tty, baud, baud);
+	tty_termios_encode_baud_rate(termios, baud, baud);
 	s->baud = baud;
 	param_mask |= MAX3100_BAUD;
 
Signature · 1 line
1.7.0.4
#13 lore raw

Re: [PATCH 12/31] tty: serial - fix tty back references in termios

A couple of build breaks in linux-next (tag: next-20100617)

drivers/serial/ioc4_serial.c:1750: error: expected statement before ‘)’ token

Would have a similar one for ioc3_serial.c if my .config included it.

Quoted 4 lines · Arnd Bergmann
drivers/serial/ioc3_serial.c +0 -0
index f164ba4..bd2e9e6 100644

...

Quoted 2 lines

-       if (I_IGNPAR(state->port.tty))
+       if (iflag & IGNPAR))

Can we have matching numbers of "(" and ")" here please.

drivers/serial/ioc4_serial.c

Quoted 4 lines
drivers/serial/ioc4_serial.c +0 -0
index 8ad28fc..2c30023 100644

..
.- if (I_IGNPAR(state->port.tty))
+ if (iflag & IGNPAR))

Same here.

-Tony

#14 lore raw

Re: [PATCH 12/31] tty: serial - fix tty back references in termios

Quoted 25 lines · Tony Luck

A couple of build breaks in linux-next (tag: next-20100617)

drivers/serial/ioc4_serial.c:1750: error: expected statement before ‘)’ token

Would have a similar one for ioc3_serial.c if my .config included it.

Quoted 4 lines · Arnd Bergmann
drivers/serial/ioc3_serial.c +0 -0
index f164ba4..bd2e9e6 100644

...

Quoted 2 lines

-       if (I_IGNPAR(state->port.tty))
+       if (iflag & IGNPAR))

Can we have matching numbers of "(" and ")" here please.

drivers/serial/ioc4_serial.c

Quoted 4 lines
drivers/serial/ioc4_serial.c +0 -0
index 8ad28fc..2c30023 100644

..
.- if (I_IGNPAR(state->port.tty))
+ if (iflag & IGNPAR))

Quoted 1 line

Same here.

I've fixed these up in my tree so the next linux-next will contain the correct ones.

thanks,

greg k-h

author maintainer
#15 lore raw

PATCH 13/31 tty: serial - fix tty referencing in set_ldisc

In reply to Arnd Bergmann

From: Alan Cox <[email protected]>

Pass down the ldisc number so that the drivers don't have to peek into the tty object themselves. This lets us get rid of another case of back referencing port to tty which we don't want (because of races versus hangup/close).

---
 drivers/serial/bfin_5xx.c    |    7 ++-----
 drivers/serial/serial_core.c |    2 +-
 include/linux/serial_core.h  |    2 +-
 3 files changed, 4 insertions(+), 7 deletions(-)
drivers/serial/bfin_5xx.c +2 -5
index 96f7e74..e0d25ca 100644
@@ -952,15 +952,12 @@ bfin_serial_verify_port(struct uart_port *port, struct serial_struct *ser)
  * Enable the IrDA function if tty->ldisc.num is N_IRDA.
  * In other cases, disable IrDA function.
  */
-static void bfin_serial_set_ldisc(struct uart_port *port)
+static void bfin_serial_set_ldisc(struct uart_port *port, int ld)
 {
 	int line = port->line;
 	unsigned short val;
 
-	if (line >= port->state->port.tty->driver->num)
-		return;
-
-	switch (port->state->port.tty->termios->c_line) {
+	switch (ld) {
 	case N_IRDA:
 		val = UART_GET_GCTL(&bfin_serial_ports[line]);
 		val |= (IREN | RPOLC);
drivers/serial/serial_core.c +1 -1
index 12ee7e0..570dca2 100644
@@ -1194,7 +1194,7 @@ static void uart_set_ldisc(struct tty_struct *tty)
 	struct uart_port *uport = state->uart_port;
 
 	if (uport->ops->set_ldisc)
-		uport->ops->set_ldisc(uport);
+		uport->ops->set_ldisc(uport, tty->termios->c_line);
 }
 
 static void uart_set_termios(struct tty_struct *tty,
include/linux/serial_core.h +1 -1
index f10db6e..3292816 100644
@@ -220,7 +220,7 @@ struct uart_ops {
 	void		(*flush_buffer)(struct uart_port *);
 	void		(*set_termios)(struct uart_port *, struct ktermios *new,
 				       struct ktermios *old);
-	void		(*set_ldisc)(struct uart_port *);
+	void		(*set_ldisc)(struct uart_port *, int new);
 	void		(*pm)(struct uart_port *, unsigned int state,
 			      unsigned int oldstate);
 	int		(*set_wake)(struct uart_port *, unsigned int state);
Signature · 1 line
1.7.0.4
author maintainer
#16 lore raw

PATCH 14/31 vc: Locking clean up

In reply to Arnd Bergmann

From: Alan Cox <[email protected]>

The virtual console layer uses the BKL for various things that don't really need it. Clean them out.

---
 drivers/char/selection.c |    4 ++++
 drivers/char/vt.c        |    7 ++++---
 2 files changed, 8 insertions(+), 3 deletions(-)
drivers/char/selection.c +4 -0
index f97b9e8..6e79340 100644
@@ -26,6 +26,7 @@
 #include <linux/selection.h>
 #include <linux/tiocl.h>
 #include <linux/console.h>
+#include <linux/smp_lock.h>
 
 /* Don't take this from <ctype.h>: 011-015 on the screen aren't spaces */
 #define isspace(c)	((c) == ' ')
@@ -312,6 +313,8 @@ int paste_selection(struct tty_struct *tty)
 	struct  tty_ldisc *ld;
 	DECLARE_WAITQUEUE(wait, current);
 
+	lock_kernel();
+
 	acquire_console_sem();
 	poke_blanked_console();
 	release_console_sem();
@@ -335,5 +338,6 @@ int paste_selection(struct tty_struct *tty)
 	__set_current_state(TASK_RUNNING);
 
 	tty_ldisc_deref(ld);
+	unlock_kernel();
 	return 0;
 }
drivers/char/vt.c +4 -3
index 7cdb6ee..9f42b1f 100644
@@ -280,8 +280,12 @@ static inline unsigned short *screenpos(struct vc_data *vc, int offset, int view
 	return p;
 }
 
+/* Called  from the keyboard irq path.. */
 static inline void scrolldelta(int lines)
 {
+	/* FIXME */
+	/* scrolldelta needs some kind of consistency lock, but the BKL was
+	   and still is not protecting versus the scheduled back end */
 	scrollback_delta += lines;
 	schedule_console_callback();
 }
@@ -2604,8 +2608,6 @@ int tioclinux(struct tty_struct *tty, unsigned long arg)
 		return -EFAULT;
 	ret = 0;
 
-	lock_kernel();
-
 	switch (type)
 	{
 		case TIOCL_SETSEL:
@@ -2680,7 +2682,6 @@ int tioclinux(struct tty_struct *tty, unsigned long arg)
 			ret = -EINVAL;
 			break;
 	}
-	unlock_kernel();
 	return ret;
 }
 
Signature · 1 line
1.7.0.4
author maintainer
#17 lore raw

PATCH 15/31 tty: Make vt's have a tty_port

In reply to Arnd Bergmann

From: Alan Cox <[email protected]>

The vt layer isn't safely handling reference counts to tty object on the input side. Add a tty port structure to the vt layer in order to implement this using the standard helpers.

---
 drivers/char/vt.c              |    2 ++
 include/linux/console_struct.h |    2 ++
 2 files changed, 4 insertions(+), 0 deletions(-)
drivers/char/vt.c +2 -0
index 9f42b1f..8c77ecb 100644
@@ -772,6 +772,7 @@ int vc_allocate(unsigned int currcons)	/* return 0 on success */
 	    if (!vc)
 		return -ENOMEM;
 	    vc_cons[currcons].d = vc;
+	    tty_port_init(&vc->port);
 	    INIT_WORK(&vc_cons[currcons].SAK_work, vc_SAK);
 	    visual_init(vc, currcons, 1);
 	    if (!*vc->vc_uni_pagedir_loc)
@@ -2909,6 +2910,7 @@ static int __init con_init(void)
 	for (currcons = 0; currcons < MIN_NR_CONSOLES; currcons++) {
 		vc_cons[currcons].d = vc = kzalloc(sizeof(struct vc_data), GFP_NOWAIT);
 		INIT_WORK(&vc_cons[currcons].SAK_work, vc_SAK);
+		tty_port_init(&vc->port);
 		visual_init(vc, currcons, 1);
 		vc->vc_screenbuf = kzalloc(vc->vc_screenbuf_size, GFP_NOWAIT);
 		vc_init(vc, vc->vc_rows, vc->vc_cols,
include/linux/console_struct.h +2 -0
index 38fe59d..57e83f1 100644
@@ -21,6 +21,8 @@ struct vt_struct;
 #define NPAR 16
 
 struct vc_data {
+	struct tty_port port;			/* Upper level data */
+
 	unsigned short	vc_num;			/* Console number */
 	unsigned int	vc_cols;		/* [#] Console size */
 	unsigned int	vc_rows;
Signature · 1 line
1.7.0.4
author maintainer
#18 lore raw

PATCH 16/31 tty: Move the vt_tty field from the vc_data into the standard tty_port

In reply to Arnd Bergmann

From: Alan Cox <[email protected]>

This takes all the tty references through the expected interface points so we can refcount them.

---
 drivers/char/keyboard.c        |   10 +++++-----
 drivers/char/vt.c              |   10 +++++-----
 drivers/char/vt_ioctl.c        |    2 +-
 include/linux/console_struct.h |    1 -
 4 files changed, 11 insertions(+), 12 deletions(-)
drivers/char/keyboard.c +5 -5
index 54109dc..ec733f1 100644
@@ -299,7 +299,7 @@ int kbd_rate(struct kbd_repeat *rep)
  */
 static void put_queue(struct vc_data *vc, int ch)
 {
-	struct tty_struct *tty = vc->vc_tty;
+	struct tty_struct *tty = vc->port.tty;
 
 	if (tty) {
 		tty_insert_flip_char(tty, ch, 0);
@@ -309,7 +309,7 @@ static void put_queue(struct vc_data *vc, int ch)
 
 static void puts_queue(struct vc_data *vc, char *cp)
 {
-	struct tty_struct *tty = vc->vc_tty;
+	struct tty_struct *tty = vc->port.tty;
 
 	if (!tty)
 		return;
@@ -485,7 +485,7 @@ static void fn_show_ptregs(struct vc_data *vc)
 
 static void fn_hold(struct vc_data *vc)
 {
-	struct tty_struct *tty = vc->vc_tty;
+	struct tty_struct *tty = vc->port.tty;
 
 	if (rep || !tty)
 		return;
@@ -563,7 +563,7 @@ static void fn_inc_console(struct vc_data *vc)
 
 static void fn_send_intr(struct vc_data *vc)
 {
-	struct tty_struct *tty = vc->vc_tty;
+	struct tty_struct *tty = vc->port.tty;
 
 	if (!tty)
 		return;
@@ -1162,7 +1162,7 @@ static void kbd_keycode(unsigned int keycode, int down, int hw_raw)
 	struct keyboard_notifier_param param = { .vc = vc, .value = keycode, .down = down };
 	int rc;
 
-	tty = vc->vc_tty;
+	tty = vc->port.tty;
 
 	if (tty && (!tty->driver_data)) {
 		/* No driver data? Strange. Okay we fix it then. */
drivers/char/vt.c +5 -5
index 8c77ecb..2f50056 100644
@@ -961,12 +961,12 @@ static int vc_do_resize(struct tty_struct *tty, struct vc_data *vc,
  *	Resize a virtual console as seen from the console end of things. We
  *	use the common vc_do_resize methods to update the structures. The
  *	caller must hold the console sem to protect console internals and
- *	vc->vc_tty
+ *	vc->port.tty
  */
 
 int vc_resize(struct vc_data *vc, unsigned int cols, unsigned int rows)
 {
-	return vc_do_resize(vc->vc_tty, vc, cols, rows);
+	return vc_do_resize(vc->port.tty, vc, cols, rows);
 }
 
 /**
@@ -2795,12 +2795,12 @@ static int con_open(struct tty_struct *tty, struct file *filp)
 			struct vc_data *vc = vc_cons[currcons].d;
 
 			/* Still being freed */
-			if (vc->vc_tty) {
+			if (vc->port.tty) {
 				release_console_sem();
 				return -ERESTARTSYS;
 			}
 			tty->driver_data = vc;
-			vc->vc_tty = tty;
+			vc->port.tty = tty;
 
 			if (!tty->winsize.ws_row && !tty->winsize.ws_col) {
 				tty->winsize.ws_row = vc_cons[currcons].d->vc_rows;
@@ -2828,7 +2828,7 @@ static void con_shutdown(struct tty_struct *tty)
 	struct vc_data *vc = tty->driver_data;
 	BUG_ON(vc == NULL);
 	acquire_console_sem();
-	vc->vc_tty = NULL;
+	vc->port.tty = NULL;
 	release_console_sem();
 	tty_shutdown(tty);
 }
drivers/char/vt_ioctl.c +1 -1
index 6aa1028..625f77d 100644
@@ -1367,7 +1367,7 @@ void vc_SAK(struct work_struct *work)
 	acquire_console_sem();
 	vc = vc_con->d;
 	if (vc) {
-		tty = vc->vc_tty;
+		tty = vc->port.tty;
 		/*
 		 * SAK should also work in all raw modes and reset
 		 * them properly.
include/linux/console_struct.h +0 -1
index 57e83f1..3364898 100644
@@ -58,7 +58,6 @@ struct vc_data {
 	/* VT terminal data */
 	unsigned int	vc_state;		/* Escape sequence parser state */
 	unsigned int	vc_npar,vc_par[NPAR];	/* Parameters of current escape sequence */
-	struct tty_struct *vc_tty;		/* TTY we are attached to */
 	/* data for manual vt switching */
 	struct vt_mode	vt_mode;
 	struct pid 	*vt_pid;
Signature · 1 line
1.7.0.4
author maintainer
#19 lore raw

PATCH 17/31 serial: Change the wait for carrier locking

In reply to Arnd Bergmann

From: Alan Cox <[email protected]>

We want to push the lock/unlock into the helper functions so that we can prepare to move to using the tty_port helper. The expansion initially comes out a bit ugly but its worth the temporary expansion IMHO just so we can produce a nice testable series of changes.

---
 drivers/serial/serial_core.c |   44 +++++++++++++++++++++++++++++++++--------
 1 files changed, 35 insertions(+), 9 deletions(-)
drivers/serial/serial_core.c +35 -9
index 570dca2..424b1c7 100644
@@ -1272,6 +1272,7 @@ static void uart_close(struct tty_struct *tty, struct file *filp)
 	struct uart_state *state = tty->driver_data;
 	struct tty_port *port;
 	struct uart_port *uport;
+	unsigned long flags;
 
 	BUG_ON(!kernel_locked());
 
@@ -1284,9 +1285,12 @@ static void uart_close(struct tty_struct *tty, struct file *filp)
 	pr_debug("uart_close(%d) called\n", uport->line);
 
 	mutex_lock(&port->mutex);
+	spin_lock_irqsave(&port->lock, flags);
 
-	if (tty_hung_up_p(filp))
+	if (tty_hung_up_p(filp)) {
+		spin_unlock_irqrestore(&port->lock, flags);
 		goto done;
+	}
 
 	if ((tty->count == 1) && (port->count != 1)) {
 		/*
@@ -1305,8 +1309,10 @@ static void uart_close(struct tty_struct *tty, struct file *filp)
 		       tty->name, port->count);
 		port->count = 0;
 	}
-	if (port->count)
+	if (port->count) {
+		spin_unlock_irqrestore(&port->lock, flags);
 		goto done;
+	}
 
 	/*
 	 * Now we wait for the transmit buffer to clear; and we notify
@@ -1314,6 +1320,7 @@ static void uart_close(struct tty_struct *tty, struct file *filp)
 	 * setting tty->closing.
 	 */
 	tty->closing = 1;
+	spin_unlock_irqrestore(&port->lock, flags);
 
 	if (port->closing_wait != ASYNC_CLOSING_WAIT_NONE)
 		tty_wait_until_sent(tty, msecs_to_jiffies(port->closing_wait));
@@ -1340,20 +1347,26 @@ static void uart_close(struct tty_struct *tty, struct file *filp)
 
 	tty_ldisc_flush(tty);
 
-	tty->closing = 0;
 	tty_port_tty_set(port, NULL);
+	spin_lock_irqsave(&port->lock, flags);
+	tty->closing = 0;
 
 	if (port->blocked_open) {
+		spin_unlock_irqrestore(&port->lock, flags);
 		if (port->close_delay)
 			msleep_interruptible(port->close_delay);
+		spin_lock_irqsave(&port->lock, flags);
 	} else if (!uart_console(uport)) {
+		spin_unlock_irqrestore(&port->lock, flags);
 		uart_change_pm(state, 3);
+		spin_lock_irqsave(&port->lock, flags);
 	}
 
 	/*
 	 * Wake up anyone trying to open this port.
 	 */
 	clear_bit(ASYNCB_NORMAL_ACTIVE, &port->flags);
+	spin_unlock_irqrestore(&port->lock, flags);
 	wake_up_interruptible(&port->open_wait);
 
 done:
@@ -1429,6 +1442,7 @@ static void uart_hangup(struct tty_struct *tty)
 {
 	struct uart_state *state = tty->driver_data;
 	struct tty_port *port = &state->port;
+	unsigned long flags;
 
 	BUG_ON(!kernel_locked());
 	pr_debug("uart_hangup(%d)\n", state->uart_port->line);
@@ -1437,8 +1451,10 @@ static void uart_hangup(struct tty_struct *tty)
 	if (port->flags & ASYNC_NORMAL_ACTIVE) {
 		uart_flush_buffer(tty);
 		uart_shutdown(tty, state);
+		spin_lock_irqsave(&port->lock, flags);
 		port->count = 0;
 		clear_bit(ASYNCB_NORMAL_ACTIVE, &port->flags);
+		spin_unlock_irqrestore(&port->lock, flags);
 		tty_port_tty_set(port, NULL);
 		wake_up_interruptible(&port->open_wait);
 		wake_up_interruptible(&port->delta_msr_wait);
@@ -1496,9 +1512,13 @@ uart_block_til_ready(struct file *filp, struct uart_state *state)
 	struct uart_port *uport = state->uart_port;
 	struct tty_port *port = &state->port;
 	unsigned int mctrl;
+	unsigned long flags;
 
+	spin_lock_irqsave(&port->lock, flags);
+	if (!tty_hung_up_p(filp))
+		port->count--;
 	port->blocked_open++;
-	port->count--;
+	spin_unlock_irqrestore(&port->lock, flags);
 
 	add_wait_queue(&port->open_wait, &wait);
 	while (1) {
@@ -1535,23 +1555,26 @@ uart_block_til_ready(struct file *filp, struct uart_state *state)
 		 * not set RTS here - we want to make sure we catch
 		 * the data from the modem.
 		 */
-		if (port->tty->termios->c_cflag & CBAUD)
+		if (port->tty->termios->c_cflag & CBAUD) {
+			mutex_lock(&port->mutex);
 			uart_set_mctrl(uport, TIOCM_DTR);
+			mutex_unlock(&port->mutex);
+		}
 
 		/*
 		 * and wait for the carrier to indicate that the
 		 * modem is ready for us.
 		 */
+		mutex_lock(&port->mutex);
 		spin_lock_irq(&uport->lock);
 		uport->ops->enable_ms(uport);
 		mctrl = uport->ops->get_mctrl(uport);
 		spin_unlock_irq(&uport->lock);
+		mutex_unlock(&port->mutex);
 		if (mctrl & TIOCM_CAR)
 			break;
 
-		mutex_unlock(&port->mutex);
 		schedule();
-		mutex_lock(&port->mutex);
 
 		if (signal_pending(current))
 			break;
@@ -1559,8 +1582,11 @@ uart_block_til_ready(struct file *filp, struct uart_state *state)
 	set_current_state(TASK_RUNNING);
 	remove_wait_queue(&port->open_wait, &wait);
 
-	port->count++;
+	spin_lock_irqsave(&port->lock, flags);
+	if (!tty_hung_up_p(filp))
+		port->count++;
 	port->blocked_open--;
+	spin_unlock_irqrestore(&port->lock, flags);
 
 	if (signal_pending(current))
 		return -ERESTARTSYS;
@@ -1677,9 +1703,9 @@ static int uart_open(struct tty_struct *tty, struct file *filp)
 	/*
 	 * If we succeeded, wait until the port is ready.
 	 */
+	mutex_unlock(&port->mutex);
 	if (retval == 0)
 		retval = uart_block_til_ready(filp, state);
-	mutex_unlock(&port->mutex);
 
 	/*
 	 * If this is the first open to succeed, adjust things to suit.
Signature · 1 line
1.7.0.4
author maintainer
#20 lore raw

PATCH 18/31 serial: add port helpers

In reply to Arnd Bergmann

From: Alan Cox <[email protected]>

We can make this the same as the ones that will be needed by the tty_port helper logic that we want to move to but still call them from the existing code base.

---
 drivers/serial/serial_core.c |   51 ++++++++++++++++++++++++++++++-----------
 1 files changed, 37 insertions(+), 14 deletions(-)
drivers/serial/serial_core.c +37 -14
index 424b1c7..2379045 100644
@@ -1501,6 +1501,34 @@ static void uart_update_termios(struct tty_struct *tty,
 	}
 }
 
+static int uart_carrier_raised(struct tty_port *port)
+{
+	struct uart_state *state = container_of(port, struct uart_state, port);
+	struct uart_port *uport = state->uart_port;
+	int mctrl;
+	mutex_lock(&port->mutex);
+	spin_lock_irq(&uport->lock);
+	uport->ops->enable_ms(uport);
+	mctrl = uport->ops->get_mctrl(uport);
+	spin_unlock_irq(&uport->lock);
+	mutex_unlock(&port->mutex);
+	if (mctrl & TIOCM_CAR)
+		return 1;
+	return 0;
+}
+
+static void uart_dtr_rts(struct tty_port *port, int onoff)
+{
+	struct uart_state *state = container_of(port, struct uart_state, port);
+	struct uart_port *uport = state->uart_port;
+	mutex_lock(&port->mutex);
+	if (onoff)
+		uart_set_mctrl(uport, TIOCM_DTR | TIOCM_RTS);
+	else
+		uart_clear_mctrl(uport, TIOCM_DTR | TIOCM_RTS);
+	mutex_unlock(&port->mutex);
+}
+
 /*
  * Block the open until the port is ready.  We must be called with
  * the per-port semaphore held.
@@ -1509,9 +1537,7 @@ static int
 uart_block_til_ready(struct file *filp, struct uart_state *state)
 {
 	DECLARE_WAITQUEUE(wait, current);
-	struct uart_port *uport = state->uart_port;
 	struct tty_port *port = &state->port;
-	unsigned int mctrl;
 	unsigned long flags;
 
 	spin_lock_irqsave(&port->lock, flags);
@@ -1555,23 +1581,14 @@ uart_block_til_ready(struct file *filp, struct uart_state *state)
 		 * not set RTS here - we want to make sure we catch
 		 * the data from the modem.
 		 */
-		if (port->tty->termios->c_cflag & CBAUD) {
-			mutex_lock(&port->mutex);
-			uart_set_mctrl(uport, TIOCM_DTR);
-			mutex_unlock(&port->mutex);
-		}
+		if (port->tty->termios->c_cflag & CBAUD)
+			tty_port_raise_dtr_rts(port);
 
 		/*
 		 * and wait for the carrier to indicate that the
 		 * modem is ready for us.
 		 */
-		mutex_lock(&port->mutex);
-		spin_lock_irq(&uport->lock);
-		uport->ops->enable_ms(uport);
-		mctrl = uport->ops->get_mctrl(uport);
-		spin_unlock_irq(&uport->lock);
-		mutex_unlock(&port->mutex);
-		if (mctrl & TIOCM_CAR)
+		if (tty_port_carrier_raised(port))
 			break;
 
 		schedule();
@@ -2349,6 +2366,11 @@ static const struct tty_operations uart_ops = {
 #endif
 };
 
+static const struct tty_port_operations uart_port_ops = {
+	.carrier_raised = uart_carrier_raised,
+	.dtr_rts	= uart_dtr_rts,
+};
+
 /**
  *	uart_register_driver - register a driver with the uart core layer
  *	@drv: low level driver structure
@@ -2405,6 +2427,7 @@ int uart_register_driver(struct uart_driver *drv)
 		struct tty_port *port = &state->port;
 
 		tty_port_init(port);
+		port->ops = &uart_port_ops;
 		port->close_delay     = 500;	/* .5 seconds */
 		port->closing_wait    = 30000;	/* 30 seconds */
 		tasklet_init(&state->tlet, uart_tasklet_action,
Signature · 1 line
1.7.0.4
author maintainer
#21 lore raw

PATCH 19/31 serial: trim locking on the helpers

In reply to Arnd Bergmann

From: Alan Cox <[email protected]>

The port mutex protects port->tty, but these paths never need to walk from port->tty. They do need the low level lock as the API expects that but they already also take it.

Thus we can drop the extra mutex lock calls here.

---
 drivers/serial/serial_core.c |    5 +----
 1 files changed, 1 insertions(+), 4 deletions(-)
drivers/serial/serial_core.c +1 -4
index 2379045..0603e0d 100644
@@ -1506,12 +1506,10 @@ static int uart_carrier_raised(struct tty_port *port)
 	struct uart_state *state = container_of(port, struct uart_state, port);
 	struct uart_port *uport = state->uart_port;
 	int mctrl;
-	mutex_lock(&port->mutex);
 	spin_lock_irq(&uport->lock);
 	uport->ops->enable_ms(uport);
 	mctrl = uport->ops->get_mctrl(uport);
 	spin_unlock_irq(&uport->lock);
-	mutex_unlock(&port->mutex);
 	if (mctrl & TIOCM_CAR)
 		return 1;
 	return 0;
@@ -1521,12 +1519,11 @@ static void uart_dtr_rts(struct tty_port *port, int onoff)
 {
 	struct uart_state *state = container_of(port, struct uart_state, port);
 	struct uart_port *uport = state->uart_port;
-	mutex_lock(&port->mutex);
+
 	if (onoff)
 		uart_set_mctrl(uport, TIOCM_DTR | TIOCM_RTS);
 	else
 		uart_clear_mctrl(uport, TIOCM_DTR | TIOCM_RTS);
-	mutex_unlock(&port->mutex);
 }
 
 /*
Signature · 1 line
1.7.0.4
author maintainer
#22 lore raw

PATCH 20/31 serial: Use block_til_ready helper

In reply to Arnd Bergmann

From: Alan Cox <[email protected]>

Our code now rather closely resembles the helper, so switch to it.

---
 drivers/serial/serial_core.c |   87 +-----------------------------------------
 1 files changed, 1 insertions(+), 86 deletions(-)
drivers/serial/serial_core.c +1 -86
index 0603e0d..a55751a 100644
@@ -1526,91 +1526,6 @@ static void uart_dtr_rts(struct tty_port *port, int onoff)
 		uart_clear_mctrl(uport, TIOCM_DTR | TIOCM_RTS);
 }
 
-/*
- * Block the open until the port is ready.  We must be called with
- * the per-port semaphore held.
- */
-static int
-uart_block_til_ready(struct file *filp, struct uart_state *state)
-{
-	DECLARE_WAITQUEUE(wait, current);
-	struct tty_port *port = &state->port;
-	unsigned long flags;
-
-	spin_lock_irqsave(&port->lock, flags);
-	if (!tty_hung_up_p(filp))
-		port->count--;
-	port->blocked_open++;
-	spin_unlock_irqrestore(&port->lock, flags);
-
-	add_wait_queue(&port->open_wait, &wait);
-	while (1) {
-		set_current_state(TASK_INTERRUPTIBLE);
-
-		/*
-		 * If we have been hung up, tell userspace/restart open.
-		 */
-		if (tty_hung_up_p(filp) || port->tty == NULL)
-			break;
-
-		/*
-		 * If the port has been closed, tell userspace/restart open.
-		 */
-		if (!(port->flags & ASYNC_INITIALIZED))
-			break;
-
-		/*
-		 * If non-blocking mode is set, or CLOCAL mode is set,
-		 * we don't want to wait for the modem status lines to
-		 * indicate that the port is ready.
-		 *
-		 * Also, if the port is not enabled/configured, we want
-		 * to allow the open to succeed here.  Note that we will
-		 * have set TTY_IO_ERROR for a non-existant port.
-		 */
-		if ((filp->f_flags & O_NONBLOCK) ||
-		    (port->tty->termios->c_cflag & CLOCAL) ||
-		    (port->tty->flags & (1 << TTY_IO_ERROR)))
-			break;
-
-		/*
-		 * Set DTR to allow modem to know we're waiting.  Do
-		 * not set RTS here - we want to make sure we catch
-		 * the data from the modem.
-		 */
-		if (port->tty->termios->c_cflag & CBAUD)
-			tty_port_raise_dtr_rts(port);
-
-		/*
-		 * and wait for the carrier to indicate that the
-		 * modem is ready for us.
-		 */
-		if (tty_port_carrier_raised(port))
-			break;
-
-		schedule();
-
-		if (signal_pending(current))
-			break;
-	}
-	set_current_state(TASK_RUNNING);
-	remove_wait_queue(&port->open_wait, &wait);
-
-	spin_lock_irqsave(&port->lock, flags);
-	if (!tty_hung_up_p(filp))
-		port->count++;
-	port->blocked_open--;
-	spin_unlock_irqrestore(&port->lock, flags);
-
-	if (signal_pending(current))
-		return -ERESTARTSYS;
-
-	if (!port->tty || tty_hung_up_p(filp))
-		return -EAGAIN;
-
-	return 0;
-}
-
 static struct uart_state *uart_get(struct uart_driver *drv, int line)
 {
 	struct uart_state *state;
@@ -1719,7 +1634,7 @@ static int uart_open(struct tty_struct *tty, struct file *filp)
 	 */
 	mutex_unlock(&port->mutex);
 	if (retval == 0)
-		retval = uart_block_til_ready(filp, state);
+		retval = tty_port_block_til_ready(port, tty, filp);
 
 	/*
 	 * If this is the first open to succeed, adjust things to suit.
Signature · 1 line
1.7.0.4
author maintainer
#23 lore raw

PATCH 21/31 tty: replace BKL with a new tty_lock

In reply to Arnd Bergmann

As a preparation for replacing the big kernel lock in the TTY layer, wrap all the callers in new macros tty_lock, tty_lock_nested and tty_unlock.

---
 drivers/char/amiserial.c       |   16 +++---
 drivers/char/briq_panel.c      |    6 +-
 drivers/char/n_hdlc.c          |   16 +++---
 drivers/char/n_r3964.c         |    8 ++--
 drivers/char/pty.c             |    4 +-
 drivers/char/selection.c       |    4 +-
 drivers/char/serial167.c       |    4 +-
 drivers/char/sx.c              |   12 ++--
 drivers/char/tty_io.c          |  115 ++++++++++++++++++++++------------------
 drivers/char/tty_ldisc.c       |   24 +++++----
 drivers/char/vc_screen.c       |    4 +-
 drivers/char/vt_ioctl.c        |   10 ++--
 drivers/serial/68360serial.c   |    4 +-
 drivers/serial/crisv10.c       |    4 +-
 drivers/serial/serial_core.c   |   10 ++--
 drivers/video/console/vgacon.c |    4 +-
 include/linux/tty.h            |   31 +++++++++++
 17 files changed, 161 insertions(+), 115 deletions(-)
drivers/char/amiserial.c +8 -8
index 4f8d60c..1b21a7a 100644
@@ -1072,7 +1072,7 @@ static int get_serial_info(struct async_struct * info,
 	if (!retinfo)
 		return -EFAULT;
 	memset(&tmp, 0, sizeof(tmp));
-	lock_kernel();
+	tty_lock();
 	tmp.type = state->type;
 	tmp.line = state->line;
 	tmp.port = state->port;
@@ -1083,7 +1083,7 @@ static int get_serial_info(struct async_struct * info,
 	tmp.close_delay = state->close_delay;
 	tmp.closing_wait = state->closing_wait;
 	tmp.custom_divisor = state->custom_divisor;
-	unlock_kernel();
+	tty_unlock();
 	if (copy_to_user(retinfo,&tmp,sizeof(*retinfo)))
 		return -EFAULT;
 	return 0;
@@ -1100,14 +1100,14 @@ static int set_serial_info(struct async_struct * info,
 	if (copy_from_user(&new_serial,new_info,sizeof(new_serial)))
 		return -EFAULT;
 
-	lock_kernel();
+	tty_lock();
 	state = info->state;
 	old_state = *state;
   
 	change_irq = new_serial.irq != state->irq;
 	change_port = (new_serial.port != state->port);
 	if(change_irq || change_port || (new_serial.xmit_fifo_size != state->xmit_fifo_size)) {
-	  unlock_kernel();
+	  tty_unlock();
 	  return -EINVAL;
 	}
   
@@ -1127,7 +1127,7 @@ static int set_serial_info(struct async_struct * info,
 	}
 
 	if (new_serial.baud_base < 9600) {
-		unlock_kernel();
+		tty_unlock();
 		return -EINVAL;
 	}
 
@@ -1163,7 +1163,7 @@ check_and_exit:
 		}
 	} else
 		retval = startup(info);
-	unlock_kernel();
+	tty_unlock();
 	return retval;
 }
 
@@ -1538,7 +1538,7 @@ static void rs_wait_until_sent(struct tty_struct *tty, int timeout)
 
 	orig_jiffies = jiffies;
 
-	lock_kernel();
+	tty_lock_nested(); /* tty_wait_until_sent is called from lots of places */
 	/*
 	 * Set the check interval to be 1/5 of the estimated time to
 	 * send a single character, and make it at least 1.  The check
@@ -1579,7 +1579,7 @@ static void rs_wait_until_sent(struct tty_struct *tty, int timeout)
 			break;
 	}
 	__set_current_state(TASK_RUNNING);
-	unlock_kernel();
+	tty_unlock();
 #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT
 	printk("lsr = %d (jiff=%lu)...done\n", lsr, jiffies);
 #endif
drivers/char/briq_panel.c +3 -3
index 555cd93..d5fa113 100644
@@ -67,15 +67,15 @@ static void set_led(char state)
 
 static int briq_panel_open(struct inode *ino, struct file *filep)
 {
-	lock_kernel();
+	tty_lock();
 	/* enforce single access, vfd_is_open is protected by BKL */
 	if (vfd_is_open) {
-		unlock_kernel();
+		tty_unlock();
 		return -EBUSY;
 	}
 	vfd_is_open = 1;
 
-	unlock_kernel();
+	tty_unlock();
 	return 0;
 }
 
drivers/char/n_hdlc.c +8 -8
index c68118e..47d3228 100644
@@ -598,18 +598,18 @@ static ssize_t n_hdlc_tty_read(struct tty_struct *tty, struct file *file,
 		return -EFAULT;
 	}
 
-	lock_kernel();
+	tty_lock();
 
 	for (;;) {
 		if (test_bit(TTY_OTHER_CLOSED, &tty->flags)) {
-			unlock_kernel();
+			tty_unlock();
 			return -EIO;
 		}
 
 		n_hdlc = tty2n_hdlc (tty);
 		if (!n_hdlc || n_hdlc->magic != HDLC_MAGIC ||
 			 tty != n_hdlc->tty) {
-			unlock_kernel();
+			tty_unlock();
 			return 0;
 		}
 
@@ -619,13 +619,13 @@ static ssize_t n_hdlc_tty_read(struct tty_struct *tty, struct file *file,
 			
 		/* no data */
 		if (file->f_flags & O_NONBLOCK) {
-			unlock_kernel();
+			tty_unlock();
 			return -EAGAIN;
 		}
 			
 		interruptible_sleep_on (&tty->read_wait);
 		if (signal_pending(current)) {
-			unlock_kernel();
+			tty_unlock();
 			return -EINTR;
 		}
 	}
@@ -648,7 +648,7 @@ static ssize_t n_hdlc_tty_read(struct tty_struct *tty, struct file *file,
 		kfree(rbuf);
 	else	
 		n_hdlc_buf_put(&n_hdlc->rx_free_buf_list,rbuf);
-	unlock_kernel();
+	tty_unlock();
 	return ret;
 	
 }	/* end of n_hdlc_tty_read() */
@@ -691,7 +691,7 @@ static ssize_t n_hdlc_tty_write(struct tty_struct *tty, struct file *file,
 		count = maxframe;
 	}
 	
-	lock_kernel();
+	tty_lock();
 
 	add_wait_queue(&tty->write_wait, &wait);
 	set_current_state(TASK_INTERRUPTIBLE);
@@ -731,7 +731,7 @@ static ssize_t n_hdlc_tty_write(struct tty_struct *tty, struct file *file,
 		n_hdlc_buf_put(&n_hdlc->tx_buf_list,tbuf);
 		n_hdlc_send_frames(n_hdlc,tty);
 	}
-	unlock_kernel();
+	tty_unlock();
 	return error;
 	
 }	/* end of n_hdlc_tty_write() */
drivers/char/n_r3964.c +4 -4
index c1d8b54..f4bd259 100644
@@ -1067,7 +1067,7 @@ static ssize_t r3964_read(struct tty_struct *tty, struct file *file,
 
 	TRACE_L("read()");
 
-	lock_kernel();
+	tty_lock();
 
 	pClient = findClient(pInfo, task_pid(current));
 	if (pClient) {
@@ -1109,7 +1109,7 @@ static ssize_t r3964_read(struct tty_struct *tty, struct file *file,
 	}
 	ret = -EPERM;
 unlock:
-	unlock_kernel();
+	tty_unlock();
 	return ret;
 }
 
@@ -1158,7 +1158,7 @@ static ssize_t r3964_write(struct tty_struct *tty, struct file *file,
 	pHeader->locks = 0;
 	pHeader->owner = NULL;
 
-	lock_kernel();
+	tty_lock();
 
 	pClient = findClient(pInfo, task_pid(current));
 	if (pClient) {
@@ -1177,7 +1177,7 @@ static ssize_t r3964_write(struct tty_struct *tty, struct file *file,
 	add_tx_queue(pInfo, pHeader);
 	trigger_transmit(pInfo);
 
-	unlock_kernel();
+	tty_unlock();
 
 	return 0;
 }
drivers/char/pty.c +2 -2
index d83a431..384e79f 100644
@@ -671,9 +671,9 @@ static int ptmx_open(struct inode *inode, struct file *filp)
 {
 	int ret;
 
-	lock_kernel();
+	tty_lock();
 	ret = __ptmx_open(inode, filp);
-	unlock_kernel();
+	tty_unlock();
 	return ret;
 }
 
drivers/char/selection.c +2 -2
index 6e79340..85211a3 100644
@@ -313,7 +313,7 @@ int paste_selection(struct tty_struct *tty)
 	struct  tty_ldisc *ld;
 	DECLARE_WAITQUEUE(wait, current);
 
-	lock_kernel();
+	tty_lock_nested(); /* always called with BTM from vt_ioctl */
 
 	acquire_console_sem();
 	poke_blanked_console();
@@ -338,6 +338,6 @@ int paste_selection(struct tty_struct *tty)
 	__set_current_state(TASK_RUNNING);
 
 	tty_ldisc_deref(ld);
-	unlock_kernel();
+	tty_unlock();
 	return 0;
 }
drivers/char/serial167.c +2 -2
index ecbe479..90b3ec0 100644
@@ -1505,7 +1505,7 @@ cy_ioctl(struct tty_struct *tty, struct file *file,
 	printk("cy_ioctl %s, cmd = %x arg = %lx\n", tty->name, cmd, arg);	/* */
 #endif
 
-	lock_kernel();
+	tty_lock();
 
 	switch (cmd) {
 	case CYGETMON:
@@ -1561,7 +1561,7 @@ cy_ioctl(struct tty_struct *tty, struct file *file,
 	default:
 		ret_val = -ENOIOCTLCMD;
 	}
-	unlock_kernel();
+	tty_unlock();
 
 #ifdef SERIAL_DEBUG_OTHER
 	printk("cy_ioctl done\n");
drivers/char/sx.c +6 -6
index a81ec4f..5b24db4 100644
@@ -1699,7 +1699,7 @@ static long sx_fw_ioctl(struct file *filp, unsigned int cmd,
 	if (!capable(CAP_SYS_RAWIO))
 		return -EPERM;
 
-	lock_kernel();
+	tty_lock();
 
 	sx_dprintk(SX_DEBUG_FIRMWARE, "IOCTL %x: %lx\n", cmd, arg);
 
@@ -1848,7 +1848,7 @@ static long sx_fw_ioctl(struct file *filp, unsigned int cmd,
 		break;
 	}
 out:
-	unlock_kernel();
+	tty_unlock();
 	func_exit();
 	return rc;
 }
@@ -1859,7 +1859,7 @@ static int sx_break(struct tty_struct *tty, int flag)
 	int rv;
 
 	func_enter();
-	lock_kernel();
+	tty_lock();
 
 	if (flag)
 		rv = sx_send_command(port, HS_START, -1, HS_IDLE_BREAK);
@@ -1868,7 +1868,7 @@ static int sx_break(struct tty_struct *tty, int flag)
 	if (rv != 1)
 		printk(KERN_ERR "sx: couldn't send break (%x).\n",
 			read_sx_byte(port->board, CHAN_OFFSET(port, hi_hstat)));
-	unlock_kernel();
+	tty_unlock();
 	func_exit();
 	return 0;
 }
@@ -1909,7 +1909,7 @@ static int sx_ioctl(struct tty_struct *tty, struct file *filp,
 	/* func_enter2(); */
 
 	rc = 0;
-	lock_kernel();
+	tty_lock();
 	switch (cmd) {
 	case TIOCGSERIAL:
 		rc = gs_getserial(&port->gs, argp);
@@ -1921,7 +1921,7 @@ static int sx_ioctl(struct tty_struct *tty, struct file *filp,
 		rc = -ENOIOCTLCMD;
 		break;
 	}
-	unlock_kernel();
+	tty_unlock();
 
 	/* func_exit(); */
 	return rc;
drivers/char/tty_io.c +64 -51

361 lines not on this page · raw message

drivers/char/tty_ldisc.c +13 -11
index 500e740..97681ff 100644
@@ -440,6 +440,8 @@ static void tty_set_termios_ldisc(struct tty_struct *tty, int num)
  *
  *	A helper opening method. Also a convenient debugging and check
  *	point.
+ *
+ *	Locking: always called with BTM already held.
  */
 
 static int tty_ldisc_open(struct tty_struct *tty, struct tty_ldisc *ld)
@@ -447,10 +449,10 @@ static int tty_ldisc_open(struct tty_struct *tty, struct tty_ldisc *ld)
 	WARN_ON(test_and_set_bit(TTY_LDISC_OPEN, &tty->flags));
 	if (ld->ops->open) {
 		int ret;
-                /* BKL here locks verus a hangup event */
-		lock_kernel();
+                /* BTM here locks versus a hangup event */
+		tty_lock_nested(); /* always held here already */
 		ret = ld->ops->open(tty);
-		unlock_kernel();
+		tty_unlock();
 		return ret;
 	}
 	return 0;
@@ -553,7 +555,7 @@ int tty_set_ldisc(struct tty_struct *tty, int ldisc)
 	if (IS_ERR(new_ldisc))
 		return PTR_ERR(new_ldisc);
 
-	lock_kernel();
+	tty_lock();
 	/*
 	 *	We need to look at the tty locking here for pty/tty pairs
 	 *	when both sides try to change in parallel.
@@ -567,12 +569,12 @@ int tty_set_ldisc(struct tty_struct *tty, int ldisc)
 	 */
 
 	if (tty->ldisc->ops->num == ldisc) {
-		unlock_kernel();
+		tty_unlock();
 		tty_ldisc_put(new_ldisc);
 		return 0;
 	}
 
-	unlock_kernel();
+	tty_unlock();
 	/*
 	 *	Problem: What do we do if this blocks ?
 	 *	We could deadlock here
@@ -594,7 +596,7 @@ int tty_set_ldisc(struct tty_struct *tty, int ldisc)
 		mutex_lock(&tty->ldisc_mutex);
 	}
 
-	lock_kernel();
+	tty_lock();
 
 	set_bit(TTY_LDISC_CHANGING, &tty->flags);
 
@@ -607,7 +609,7 @@ int tty_set_ldisc(struct tty_struct *tty, int ldisc)
 
 	o_ldisc = tty->ldisc;
 
-	unlock_kernel();
+	tty_unlock();
 	/*
 	 *	Make sure we don't change while someone holds a
 	 *	reference to the line discipline. The TTY_LDISC bit
@@ -633,14 +635,14 @@ int tty_set_ldisc(struct tty_struct *tty, int ldisc)
 	flush_scheduled_work();
 
 	mutex_lock(&tty->ldisc_mutex);
-	lock_kernel();
+	tty_lock();
 	if (test_bit(TTY_HUPPED, &tty->flags)) {
 		/* We were raced by the hangup method. It will have stomped
 		   the ldisc data and closed the ldisc down */
 		clear_bit(TTY_LDISC_CHANGING, &tty->flags);
 		mutex_unlock(&tty->ldisc_mutex);
 		tty_ldisc_put(new_ldisc);
-		unlock_kernel();
+		tty_unlock();
 		return -EIO;
 	}
 
@@ -682,7 +684,7 @@ int tty_set_ldisc(struct tty_struct *tty, int ldisc)
 	if (o_work)
 		schedule_delayed_work(&o_tty->buf.work, 1);
 	mutex_unlock(&tty->ldisc_mutex);
-	unlock_kernel();
+	tty_unlock();
 	return retval;
 }
 
drivers/char/vc_screen.c +2 -2
index c1791a6..bcce46c 100644
@@ -463,10 +463,10 @@ vcs_open(struct inode *inode, struct file *filp)
 	unsigned int currcons = iminor(inode) & 127;
 	int ret = 0;
 	
-	lock_kernel();
+	tty_lock();
 	if(currcons && !vc_cons_allocated(currcons-1))
 		ret = -ENXIO;
-	unlock_kernel();
+	tty_unlock();
 	return ret;
 }
 
drivers/char/vt_ioctl.c +5 -5
index 625f77d..cc07fab 100644
@@ -509,7 +509,7 @@ int vt_ioctl(struct tty_struct *tty, struct file * file,
 
 	console = vc->vc_num;
 
-	lock_kernel();
+	tty_lock();
 
 	if (!vc_cons_allocated(console)) { 	/* impossible? */
 		ret = -ENOIOCTLCMD;
@@ -1334,7 +1334,7 @@ int vt_ioctl(struct tty_struct *tty, struct file * file,
 		ret = -ENOIOCTLCMD;
 	}
 out:
-	unlock_kernel();
+	tty_unlock();
 	return ret;
 eperm:
 	ret = -EPERM;
@@ -1501,7 +1501,7 @@ long vt_compat_ioctl(struct tty_struct *tty, struct file * file,
 
 	console = vc->vc_num;
 
-	lock_kernel();
+	tty_lock();
 
 	if (!vc_cons_allocated(console)) { 	/* impossible? */
 		ret = -ENOIOCTLCMD;
@@ -1569,11 +1569,11 @@ long vt_compat_ioctl(struct tty_struct *tty, struct file * file,
 		goto fallback;
 	}
 out:
-	unlock_kernel();
+	tty_unlock();
 	return ret;
 
 fallback:
-	unlock_kernel();
+	tty_unlock();
 	return vt_ioctl(tty, file, cmd, arg);
 }
 
drivers/serial/68360serial.c +2 -2
index 24661cd..c17a595 100644
@@ -1705,7 +1705,7 @@ static void rs_360_wait_until_sent(struct tty_struct *tty, int timeout)
 	printk("jiff=%lu...", jiffies);
 #endif
 
-	lock_kernel();
+	tty_lock_nested(); /* always held already since we come from ->close */
 	/* We go through the loop at least once because we can't tell
 	 * exactly when the last character exits the shifter.  There can
 	 * be at least two characters waiting to be sent after the buffers
@@ -1734,7 +1734,7 @@ static void rs_360_wait_until_sent(struct tty_struct *tty, int timeout)
 			bdp--;
 	} while (bdp->status & BD_SC_READY);
 	current->state = TASK_RUNNING;
-	unlock_kernel();
+	tty_unlock();
 #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT
 	printk("lsr = %d (jiff=%lu)...done\n", lsr, jiffies);
 #endif
drivers/serial/crisv10.c +2 -2
index 31f1723..d11d898 100644
@@ -3924,7 +3924,7 @@ static void rs_wait_until_sent(struct tty_struct *tty, int timeout)
 	 * Check R_DMA_CHx_STATUS bit 0-6=number of available bytes in FIFO
 	 * R_DMA_CHx_HWSW bit 31-16=nbr of bytes left in DMA buffer (0=64k)
 	 */
-	lock_kernel();
+	tty_lock_nested(); /* locked already when coming from close */
 	orig_jiffies = jiffies;
 	while (info->xmit.head != info->xmit.tail || /* More in send queue */
 	       (*info->ostatusadr & 0x007f) ||  /* more in FIFO */
@@ -3941,7 +3941,7 @@ static void rs_wait_until_sent(struct tty_struct *tty, int timeout)
 			curr_time_usec - info->last_tx_active_usec;
 	}
 	set_current_state(TASK_RUNNING);
-	unlock_kernel();
+	tty_unlock();
 }
 
 /*
drivers/serial/serial_core.c +5 -5
index a55751a..4b151a4 100644
@@ -1274,7 +1274,7 @@ static void uart_close(struct tty_struct *tty, struct file *filp)
 	struct uart_port *uport;
 	unsigned long flags;
 
-	BUG_ON(!kernel_locked());
+	BUG_ON(!tty_locked());
 
 	if (!state)
 		return;
@@ -1382,7 +1382,7 @@ static void uart_wait_until_sent(struct tty_struct *tty, int timeout)
 	if (port->type == PORT_UNKNOWN || port->fifosize == 0)
 		return;
 
-	lock_kernel();
+	tty_lock_nested(); /* already locked when coming from close */
 
 	/*
 	 * Set the check interval to be 1/5 of the estimated time to
@@ -1429,7 +1429,7 @@ static void uart_wait_until_sent(struct tty_struct *tty, int timeout)
 			break;
 	}
 	set_current_state(TASK_RUNNING); /* might not be needed */
-	unlock_kernel();
+	tty_unlock();
 }
 
 /*
@@ -1444,7 +1444,7 @@ static void uart_hangup(struct tty_struct *tty)
 	struct tty_port *port = &state->port;
 	unsigned long flags;
 
-	BUG_ON(!kernel_locked());
+	BUG_ON(!tty_locked());
 	pr_debug("uart_hangup(%d)\n", state->uart_port->line);
 
 	mutex_lock(&port->mutex);
@@ -1570,7 +1570,7 @@ static int uart_open(struct tty_struct *tty, struct file *filp)
 	struct tty_port *port;
 	int retval, line = tty->index;
 
-	BUG_ON(!kernel_locked());
+	BUG_ON(!tty_locked());
 	pr_debug("uart_open(%d) called\n", line);
 
 	/*
drivers/video/console/vgacon.c +2 -2
index 182dd6f..7197005 100644
@@ -1108,7 +1108,7 @@ static int vgacon_do_font_op(struct vgastate *state,char *arg,int set,int ch512)
 		charmap += 4 * cmapsz;
 #endif
 
-	unlock_kernel();
+	tty_unlock();
 	spin_lock_irq(&vga_lock);
 	/* First, the Sequencer */
 	vga_wseq(state->vgabase, VGA_SEQ_RESET, 0x1);
@@ -1192,7 +1192,7 @@ static int vgacon_do_font_op(struct vgastate *state,char *arg,int set,int ch512)
 		vga_wattr(state->vgabase, VGA_AR_ENABLE_DISPLAY, 0);	
 	}
 	spin_unlock_irq(&vga_lock);
-	lock_kernel();
+	tty_lock();
 	return 0;
 }
 
include/linux/tty.h +31 -0
index 931078b..faf0bcd 100644
@@ -13,6 +13,7 @@
 #include <linux/tty_driver.h>
 #include <linux/tty_ldisc.h>
 #include <linux/mutex.h>
+#include <linux/smp_lock.h>
 
 #include <asm/system.h>
 
@@ -572,5 +573,35 @@ extern int vt_ioctl(struct tty_struct *tty, struct file *file,
 extern long vt_compat_ioctl(struct tty_struct *tty, struct file * file,
 		     unsigned int cmd, unsigned long arg);
 
+/* functions for preparation of BKL removal */
+
+/*
+ * tty_lock_nested get the tty_lock while potentially holding it
+ *
+ * The Big TTY Mutex is a recursive lock, meaning you can take it
+ * from a thread that is already holding it.
+ * This is bad for a number of reasons, so tty_lock_nested should
+ * really be used as rarely as possible. If a code location can
+ * be shown to never get called with this held already, it should
+ * use tty_lock() instead.
+ */
+static inline void __lockfunc tty_lock_nested(void) __acquires(kernel_lock)
+{
+	lock_kernel();
+}
+static inline void tty_lock(void) __acquires(kernel_lock)
+{
+#ifdef CONFIG_LOCK_KERNEL
+	/* kernel_locked is 1 for !CONFIG_LOCK_KERNEL */
+	WARN_ON(kernel_locked());
+#endif
+	lock_kernel();
+}
+static inline void tty_unlock(void) __releases(kernel_lock)
+{
+	unlock_kernel();
+}
+#define tty_locked()		(kernel_locked())
+
 #endif /* __KERNEL__ */
 #endif
Signature · 1 line
1.7.0.4
author maintainer
#24 lore raw

PATCH 22/31 tty: never hold BTM while getting tty_mutex

In reply to Arnd Bergmann

tty_mutex is never taken with the BTM held, except for two corner cases that are worked around here. We give up the BTM before calling tty_release() in the error path of tty_open().
Similarly, we reorder the locking in ptmx_open() to get tty_mutex before the BTM.

---
 drivers/char/pty.c    |   24 +++++++++++-------------
 drivers/char/tty_io.c |   12 ++++++------
 2 files changed, 17 insertions(+), 19 deletions(-)
drivers/char/pty.c +11 -13
index 384e79f..d9c1407 100644
@@ -626,7 +626,7 @@ static const struct tty_operations pty_unix98_ops = {
  *		allocated_ptys_lock handles the list of free pty numbers
  */
 
-static int __ptmx_open(struct inode *inode, struct file *filp)
+static int ptmx_open(struct inode *inode, struct file *filp)
 {
 	struct tty_struct *tty;
 	int retval;
@@ -635,11 +635,14 @@ static int __ptmx_open(struct inode *inode, struct file *filp)
 	nonseekable_open(inode, filp);
 
 	/* find a device that is not in use. */
+	tty_lock();
 	index = devpts_new_index(inode);
+	tty_unlock();
 	if (index < 0)
 		return index;
 
 	mutex_lock(&tty_mutex);
+	tty_lock();
 	tty = tty_init_dev(ptm_driver, index, 1);
 	mutex_unlock(&tty_mutex);
 
@@ -657,24 +660,19 @@ static int __ptmx_open(struct inode *inode, struct file *filp)
 		goto out1;
 
 	retval = ptm_driver->ops->open(tty, filp);
-	if (!retval)
-		return 0;
+	if (retval)
+		goto out2;
 out1:
+	tty_unlock();
+	return retval;
+out2:
+	tty_unlock();
 	tty_release(inode, filp);
 	return retval;
 out:
 	devpts_kill_index(inode, index);
-	return retval;
-}
-
-static int ptmx_open(struct inode *inode, struct file *filp)
-{
-	int ret;
-
-	tty_lock();
-	ret = __ptmx_open(inode, filp);
 	tty_unlock();
-	return ret;
+	return retval;
 }
 
 static struct file_operations ptmx_fops;
drivers/char/tty_io.c +6 -6
index 4c2cc6b..d51993b 100644
@@ -1866,19 +1866,19 @@ got_driver:
 		printk(KERN_DEBUG "error %d in opening %s...", retval,
 		       tty->name);
 #endif
+		tty_unlock(); /* need to call tty_release without BTM */
 		tty_release(inode, filp);
-		if (retval != -ERESTARTSYS) {
-			tty_unlock();
+		if (retval != -ERESTARTSYS)
 			return retval;
-		}
-		if (signal_pending(current)) {
-			tty_unlock();
+
+		if (signal_pending(current))
 			return retval;
-		}
+
 		schedule();
 		/*
 		 * Need to reset f_op in case a hangup happened.
 		 */
+		tty_lock();
 		if (filp->f_op == &hung_up_tty_fops)
 			filp->f_op = &tty_fops;
 		tty_unlock();
Signature · 1 line
1.7.0.4
author maintainer
#25 lore raw

PATCH 23/31 tty: fix console_sem lock order

In reply to Arnd Bergmann

vgacon_do_font_op releases and reacquires the BTM while holding console_sem. This violates the rule that BTM has to be the outer lock whenever we hold both.

There does not seem to be any reason to give up the BTM here, so just stop doing that.

---
 drivers/video/console/vgacon.c |    2 --
 1 files changed, 0 insertions(+), 2 deletions(-)
drivers/video/console/vgacon.c +0 -2
index 7197005..54e32c5 100644
@@ -1108,7 +1108,6 @@ static int vgacon_do_font_op(struct vgastate *state,char *arg,int set,int ch512)
 		charmap += 4 * cmapsz;
 #endif
 
-	tty_unlock();
 	spin_lock_irq(&vga_lock);
 	/* First, the Sequencer */
 	vga_wseq(state->vgabase, VGA_SEQ_RESET, 0x1);
@@ -1192,7 +1191,6 @@ static int vgacon_do_font_op(struct vgastate *state,char *arg,int set,int ch512)
 		vga_wattr(state->vgabase, VGA_AR_ENABLE_DISPLAY, 0);	
 	}
 	spin_unlock_irq(&vga_lock);
-	tty_lock();
 	return 0;
 }
 
Signature · 1 line
1.7.0.4
author maintainer
#26 lore raw

PATCH 24/31 cdc-acm: remove dead code

In reply to Arnd Bergmann

The wait_event_interruptible_timeout in acm_port_down is never reached. Remove it to avoid possible deadlocks with the big tty mutex if someone were to start using the blocking version of acm_port_down.

---
 drivers/usb/class/cdc-acm.c |   12 +++---------
 1 files changed, 3 insertions(+), 9 deletions(-)
drivers/usb/class/cdc-acm.c +3 -9
index 0c2f14f..d00d155 100644
@@ -636,19 +636,13 @@ static void acm_tty_unregister(struct acm *acm)
 
 static int acm_tty_chars_in_buffer(struct tty_struct *tty);
 
-static void acm_port_down(struct acm *acm, int drain)
+static void acm_port_down(struct acm *acm)
 {
 	int i, nr = acm->rx_buflimit;
 	mutex_lock(&open_mutex);
 	if (acm->dev) {
 		usb_autopm_get_interface(acm->control);
 		acm_set_control(acm, acm->ctrlout = 0);
-		/* try letting the last writes drain naturally */
-		if (drain) {
-			wait_event_interruptible_timeout(acm->drain_wait,
-				(ACM_NW == acm_wb_is_avail(acm)) || !acm->dev,
-					ACM_CLOSE_TIMEOUT * HZ);
-		}
 		usb_kill_urb(acm->ctrlurb);
 		for (i = 0; i < ACM_NW; i++)
 			usb_kill_urb(acm->wb[i].urb);
@@ -664,7 +658,7 @@ static void acm_tty_hangup(struct tty_struct *tty)
 {
 	struct acm *acm = tty->driver_data;
 	tty_port_hangup(&acm->port);
-	acm_port_down(acm, 0);
+	acm_port_down(acm);
 }
 
 static void acm_tty_close(struct tty_struct *tty, struct file *filp)
@@ -685,7 +679,7 @@ static void acm_tty_close(struct tty_struct *tty, struct file *filp)
 		mutex_unlock(&open_mutex);
 		return;
 	}
-	acm_port_down(acm, 0);
+	acm_port_down(acm);
 	tty_port_close_end(&acm->port, tty);
 	tty_port_tty_set(&acm->port, NULL);
 }
Signature · 1 line
1.7.0.4
author maintainer
#27 lore raw

PATCH 25/31 tty: introduce wait_event_interruptible_tty

In reply to Arnd Bergmann

Calling wait_event_interruptible implicitly
releases the BKL when it sleeps, but we need
to do this explcitly when we have converted
it to a mutex.

---
 drivers/char/cyclades.c  |    2 +-
 drivers/char/istallion.c |   12 ++++++++----
 drivers/char/n_r3964.c   |    2 +-
 drivers/char/tty_port.c  |    2 +-
 drivers/char/vt_ioctl.c  |    2 +-
 drivers/serial/crisv10.c |    4 ++--
 include/linux/tty.h      |   42 ++++++++++++++++++++++++++++++++++++++++++
 7 files changed, 56 insertions(+), 10 deletions(-)
drivers/char/cyclades.c +1 -1
index 51acfe3..27aad94 100644
@@ -1607,7 +1607,7 @@ static int cy_open(struct tty_struct *tty, struct file *filp)
 	 * If the port is the middle of closing, bail out now
 	 */
 	if (tty_hung_up_p(filp) || (info->port.flags & ASYNC_CLOSING)) {
-		wait_event_interruptible(info->port.close_wait,
+		wait_event_interruptible_tty(info->port.close_wait,
 				!(info->port.flags & ASYNC_CLOSING));
 		return (info->port.flags & ASYNC_HUP_NOTIFY) ? -EAGAIN: -ERESTARTSYS;
 	}
drivers/char/istallion.c +8 -4
index 5e9a81d..be28391 100644
@@ -954,7 +954,7 @@ static int stli_rawopen(struct stlibrd *brdp, struct stliport *portp, unsigned l
  *	order of opens and closes may not be preserved across shared
  *	memory, so we must wait until it is complete.
  */
-	wait_event_interruptible(portp->raw_wait,
+	wait_event_interruptible_tty(portp->raw_wait,
 			!test_bit(ST_CLOSING, &portp->state));
 	if (signal_pending(current)) {
 		return -ERESTARTSYS;
@@ -989,7 +989,7 @@ static int stli_rawopen(struct stlibrd *brdp, struct stliport *portp, unsigned l
 	set_bit(ST_OPENING, &portp->state);
 	spin_unlock_irqrestore(&brd_lock, flags);
 
-	wait_event_interruptible(portp->raw_wait,
+	wait_event_interruptible_tty(portp->raw_wait,
 			!test_bit(ST_OPENING, &portp->state));
 	if (signal_pending(current))
 		rc = -ERESTARTSYS;
@@ -1020,7 +1020,7 @@ static int stli_rawclose(struct stlibrd *brdp, struct stliport *portp, unsigned
  *	occurs on this port.
  */
 	if (wait) {
-		wait_event_interruptible(portp->raw_wait,
+		wait_event_interruptible_tty(portp->raw_wait,
 				!test_bit(ST_CLOSING, &portp->state));
 		if (signal_pending(current)) {
 			return -ERESTARTSYS;
@@ -1052,7 +1052,7 @@ static int stli_rawclose(struct stlibrd *brdp, struct stliport *portp, unsigned
  *	to come back.
  */
 	rc = 0;
-	wait_event_interruptible(portp->raw_wait,
+	wait_event_interruptible_tty(portp->raw_wait,
 			!test_bit(ST_CLOSING, &portp->state));
 	if (signal_pending(current))
 		rc = -ERESTARTSYS;
@@ -1073,6 +1073,10 @@ static int stli_rawclose(struct stlibrd *brdp, struct stliport *portp, unsigned
 
 static int stli_cmdwait(struct stlibrd *brdp, struct stliport *portp, unsigned long cmd, void *arg, int size, int copyback)
 {
+	/*
+	 * no need for wait_event_tty because clearing ST_CMDING cannot block
+	 * on BTM
+	 */
 	wait_event_interruptible(portp->raw_wait,
 			!test_bit(ST_CMDING, &portp->state));
 	if (signal_pending(current))
drivers/char/n_r3964.c +1 -1
index f4bd259..a98290d 100644
@@ -1079,7 +1079,7 @@ static ssize_t r3964_read(struct tty_struct *tty, struct file *file,
 				goto unlock;
 			}
 			/* block until there is a message: */
-			wait_event_interruptible(pInfo->read_wait,
+			wait_event_interruptible_tty(pInfo->read_wait,
 					(pMsg = remove_msg(pInfo, pClient)));
 		}
 
drivers/char/tty_port.c +1 -1
index a3bd1d0..35eb304 100644
@@ -231,7 +231,7 @@ int tty_port_block_til_ready(struct tty_port *port,
 
 	/* block if port is in the process of being closed */
 	if (tty_hung_up_p(filp) || port->flags & ASYNC_CLOSING) {
-		wait_event_interruptible(port->close_wait,
+		wait_event_interruptible_tty(port->close_wait,
 				!(port->flags & ASYNC_CLOSING));
 		if (port->flags & ASYNC_HUP_NOTIFY)
 			return -EAGAIN;
drivers/char/vt_ioctl.c +1 -1
index cc07fab..c56c4f3 100644
@@ -133,7 +133,7 @@ static void vt_event_wait(struct vt_event_wait *vw)
 	list_add(&vw->list, &vt_events);
 	spin_unlock_irqrestore(&vt_event_lock, flags);
 	/* Wait for it to pass */
-	wait_event_interruptible(vt_event_waitqueue, vw->done);
+	wait_event_interruptible_tty(vt_event_waitqueue, vw->done);
 	/* Dequeue it */
 	spin_lock_irqsave(&vt_event_lock, flags);
 	list_del(&vw->list);
drivers/serial/crisv10.c +2 -2
index d11d898..e6a1cb7 100644
@@ -3981,7 +3981,7 @@ block_til_ready(struct tty_struct *tty, struct file * filp,
 	 */
 	if (tty_hung_up_p(filp) ||
 	    (info->flags & ASYNC_CLOSING)) {
-		wait_event_interruptible(info->close_wait,
+		wait_event_interruptible_tty(info->close_wait,
 			!(info->flags & ASYNC_CLOSING));
 #ifdef SERIAL_DO_RESTART
 		if (info->flags & ASYNC_HUP_NOTIFY)
@@ -4139,7 +4139,7 @@ rs_open(struct tty_struct *tty, struct file * filp)
 	 */
 	if (tty_hung_up_p(filp) ||
 	    (info->flags & ASYNC_CLOSING)) {
-		wait_event_interruptible(info->close_wait,
+		wait_event_interruptible_tty(info->close_wait,
 			!(info->flags & ASYNC_CLOSING));
 #ifdef SERIAL_DO_RESTART
 		return ((info->flags & ASYNC_HUP_NOTIFY) ?
include/linux/tty.h +42 -0

47 lines not on this page · raw message

Signature · 1 line
1.7.0.4
author maintainer
#28 lore raw

PATCH 26/31 tty: reorder ldisc locking

In reply to Arnd Bergmann

We need to release the BTM in paste_selection() when sleeping in tty_ldisc_ref_wait to avoid deadlocks with tty_ldisc_enable.

In tty_set_ldisc, we now always grab the BTM before taking the ldisc_mutex in order to avoid AB-BA deadlocks between the two.

tty_ldisc_halt potentially blocks on a workqueue function that takes the BTM, so we must release the BTM before calling it.

---
 drivers/char/selection.c |    9 +++++++--
 drivers/char/tty_ldisc.c |   24 ++++++++++++++++++++----
 2 files changed, 27 insertions(+), 6 deletions(-)
drivers/char/selection.c +7 -2
index 85211a3..75889cd 100644
@@ -319,8 +319,13 @@ int paste_selection(struct tty_struct *tty)
 	poke_blanked_console();
 	release_console_sem();
 
-	ld = tty_ldisc_ref_wait(tty);
-	
+	ld = tty_ldisc_ref(tty);
+	if (!ld) {
+		tty_unlock();
+		ld = tty_ldisc_ref_wait(tty);
+		tty_lock();
+	}
+
 	add_wait_queue(&vc->paste_wait, &wait);
 	while (sel_buffer && sel_buffer_lth > pasted) {
 		set_current_state(TASK_INTERRUPTIBLE);
drivers/char/tty_ldisc.c +20 -4
index 97681ff..0f49479 100644
@@ -582,6 +582,7 @@ int tty_set_ldisc(struct tty_struct *tty, int ldisc)
 
 	tty_wait_until_sent(tty, 0);
 
+	tty_lock();
 	mutex_lock(&tty->ldisc_mutex);
 
 	/*
@@ -591,13 +592,13 @@ int tty_set_ldisc(struct tty_struct *tty, int ldisc)
 
 	while (test_bit(TTY_LDISC_CHANGING, &tty->flags)) {
 		mutex_unlock(&tty->ldisc_mutex);
+		tty_unlock();
 		wait_event(tty_ldisc_wait,
 			test_bit(TTY_LDISC_CHANGING, &tty->flags) == 0);
+		tty_lock();
 		mutex_lock(&tty->ldisc_mutex);
 	}
 
-	tty_lock();
-
 	set_bit(TTY_LDISC_CHANGING, &tty->flags);
 
 	/*
@@ -634,8 +635,8 @@ int tty_set_ldisc(struct tty_struct *tty, int ldisc)
 
 	flush_scheduled_work();
 
-	mutex_lock(&tty->ldisc_mutex);
 	tty_lock();
+	mutex_lock(&tty->ldisc_mutex);
 	if (test_bit(TTY_HUPPED, &tty->flags)) {
 		/* We were raced by the hangup method. It will have stomped
 		   the ldisc data and closed the ldisc down */
@@ -782,7 +783,20 @@ void tty_ldisc_hangup(struct tty_struct *tty)
 	 * Avoid racing set_ldisc or tty_ldisc_release
 	 */
 	mutex_lock(&tty->ldisc_mutex);
-	tty_ldisc_halt(tty);
+
+	/*
+	 * this is like tty_ldisc_halt, but we need to give up
+	 * the BTM before calling cancel_delayed_work_sync,
+	 * which may need to wait for another function taking the BTM
+	 */
+	clear_bit(TTY_LDISC, &tty->flags);
+	tty_unlock();
+	cancel_delayed_work_sync(&tty->buf.work);
+	mutex_unlock(&tty->ldisc_mutex);
+
+	tty_lock();
+	mutex_lock(&tty->ldisc_mutex);
+
 	/* At this point we have a closed ldisc and we want to
 	   reopen it. We could defer this to the next open but
 	   it means auditing a lot of other paths so this is
@@ -853,8 +867,10 @@ void tty_ldisc_release(struct tty_struct *tty, struct tty_struct *o_tty)
 	 * race with the set_ldisc code path.
 	 */
 
+	tty_unlock();
 	tty_ldisc_halt(tty);
 	flush_scheduled_work();
+	tty_lock();
 
 	mutex_lock(&tty->ldisc_mutex);
 	/*
Signature · 1 line
1.7.0.4
author maintainer
#29 lore raw

PATCH 27/31 tty: untangle locking of wait_until_sent

In reply to Arnd Bergmann

Some wait_until_sent versions require the big tty mutex, others don't and some callers of wait_until_sent already hold it while other don't. That leads to recursive use of the BTM in these functions, which we're trying to get rid of.

This turns all cleans up the locking there so that the driver's wait_until_sent function never takes the BTM itself if it is already called with that lock held.

---
 drivers/char/amiserial.c     |   11 +++++++++--
 drivers/serial/68360serial.c |    2 --
 drivers/serial/crisv10.c     |    2 --
 drivers/serial/serial_core.c |   31 ++++++++++++++++++++++---------
 4 files changed, 31 insertions(+), 15 deletions(-)
drivers/char/amiserial.c +9 -2
index 1b21a7a..8228e61 100644
@@ -1528,6 +1528,7 @@ static void rs_wait_until_sent(struct tty_struct *tty, int timeout)
 {
 	struct async_struct * info = tty->driver_data;
 	unsigned long orig_jiffies, char_time;
+	int tty_was_locked = tty_locked();
 	int lsr;
 
 	if (serial_paranoia_check(info, tty->name, "rs_wait_until_sent"))
@@ -1538,7 +1539,12 @@ static void rs_wait_until_sent(struct tty_struct *tty, int timeout)
 
 	orig_jiffies = jiffies;
 
-	tty_lock_nested(); /* tty_wait_until_sent is called from lots of places */
+	/*
+	 * tty_wait_until_sent is called from lots of places,
+	 * with or without the BTM.
+	 */
+	if (!tty_was_locked)
+		tty_lock();
 	/*
 	 * Set the check interval to be 1/5 of the estimated time to
 	 * send a single character, and make it at least 1.  The check
@@ -1579,7 +1585,8 @@ static void rs_wait_until_sent(struct tty_struct *tty, int timeout)
 			break;
 	}
 	__set_current_state(TASK_RUNNING);
-	tty_unlock();
+	if (!tty_was_locked)
+		tty_unlock();
 #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT
 	printk("lsr = %d (jiff=%lu)...done\n", lsr, jiffies);
 #endif
drivers/serial/68360serial.c +0 -2
index c17a595..5b7b801 100644
@@ -1705,7 +1705,6 @@ static void rs_360_wait_until_sent(struct tty_struct *tty, int timeout)
 	printk("jiff=%lu...", jiffies);
 #endif
 
-	tty_lock_nested(); /* always held already since we come from ->close */
 	/* We go through the loop at least once because we can't tell
 	 * exactly when the last character exits the shifter.  There can
 	 * be at least two characters waiting to be sent after the buffers
@@ -1734,7 +1733,6 @@ static void rs_360_wait_until_sent(struct tty_struct *tty, int timeout)
 			bdp--;
 	} while (bdp->status & BD_SC_READY);
 	current->state = TASK_RUNNING;
-	tty_unlock();
 #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT
 	printk("lsr = %d (jiff=%lu)...done\n", lsr, jiffies);
 #endif
drivers/serial/crisv10.c +0 -2
index e6a1cb7..0825d4a 100644
@@ -3924,7 +3924,6 @@ static void rs_wait_until_sent(struct tty_struct *tty, int timeout)
 	 * Check R_DMA_CHx_STATUS bit 0-6=number of available bytes in FIFO
 	 * R_DMA_CHx_HWSW bit 31-16=nbr of bytes left in DMA buffer (0=64k)
 	 */
-	tty_lock_nested(); /* locked already when coming from close */
 	orig_jiffies = jiffies;
 	while (info->xmit.head != info->xmit.tail || /* More in send queue */
 	       (*info->ostatusadr & 0x007f) ||  /* more in FIFO */
@@ -3941,7 +3940,6 @@ static void rs_wait_until_sent(struct tty_struct *tty, int timeout)
 			curr_time_usec - info->last_tx_active_usec;
 	}
 	set_current_state(TASK_RUNNING);
-	tty_unlock();
 }
 
 /*
drivers/serial/serial_core.c +22 -9
index 4b151a4..78b1eac 100644
@@ -60,7 +60,7 @@ static struct lock_class_key port_lock_key;
 
 static void uart_change_speed(struct tty_struct *tty, struct uart_state *state,
 					struct ktermios *old_termios);
-static void uart_wait_until_sent(struct tty_struct *tty, int timeout);
+static void __uart_wait_until_sent(struct uart_port *port, int timeout);
 static void uart_change_pm(struct uart_state *state, int pm_state);
 
 /*
@@ -1322,8 +1322,16 @@ static void uart_close(struct tty_struct *tty, struct file *filp)
 	tty->closing = 1;
 	spin_unlock_irqrestore(&port->lock, flags);
 
-	if (port->closing_wait != ASYNC_CLOSING_WAIT_NONE)
-		tty_wait_until_sent(tty, msecs_to_jiffies(port->closing_wait));
+	if (port->closing_wait != ASYNC_CLOSING_WAIT_NONE) {
+		/*
+		 * hack: open-coded tty_wait_until_sent to avoid
+		 * recursive tty_lock
+		 */
+		long timeout = msecs_to_jiffies(port->closing_wait);
+		if (wait_event_interruptible_timeout(tty->write_wait,
+				!tty_chars_in_buffer(tty), timeout) >= 0)
+			__uart_wait_until_sent(uport, timeout);
+	}
 
 	/*
 	 * At this point, we stop accepting input.  To do this, we
@@ -1339,7 +1347,7 @@ static void uart_close(struct tty_struct *tty, struct file *filp)
 		 * has completely drained; this is especially
 		 * important if there is a transmit FIFO!
 		 */
-		uart_wait_until_sent(tty, uport->timeout);
+		__uart_wait_until_sent(uport, uport->timeout);
 	}
 
 	uart_shutdown(tty, state);
@@ -1373,17 +1381,13 @@ done:
 	mutex_unlock(&port->mutex);
 }
 
-static void uart_wait_until_sent(struct tty_struct *tty, int timeout)
+static void __uart_wait_until_sent(struct uart_port *port, int timeout)
 {
-	struct uart_state *state = tty->driver_data;
-	struct uart_port *port = state->uart_port;
 	unsigned long char_time, expire;
 
 	if (port->type == PORT_UNKNOWN || port->fifosize == 0)
 		return;
 
-	tty_lock_nested(); /* already locked when coming from close */
-
 	/*
 	 * Set the check interval to be 1/5 of the estimated time to
 	 * send a single character, and make it at least 1.  The check
@@ -1429,6 +1433,15 @@ static void uart_wait_until_sent(struct tty_struct *tty, int timeout)
 			break;
 	}
 	set_current_state(TASK_RUNNING); /* might not be needed */
+}
+
+static void uart_wait_until_sent(struct tty_struct *tty, int timeout)
+{
+	struct uart_state *state = tty->driver_data;
+	struct uart_port *port = state->uart_port;
+
+	tty_lock();
+	__uart_wait_until_sent(port, timeout);
 	tty_unlock();
 }
 
Signature · 1 line
1.7.0.4
author maintainer
#30 lore raw

PATCH 28/31 tty: remove tty_lock_nested

In reply to Arnd Bergmann

This changes all remaining users of tty_lock_nested to be non-recursive, which lets us kill this function. As a consequence, we won't need to keep the lock count any more, which allows more simplifications later.

---
 drivers/char/pty.c       |    2 +-
 drivers/char/selection.c |    4 ++--
 drivers/char/tty_io.c    |   41 ++++++++++++++++++++---------------------
 drivers/char/tty_ldisc.c |    3 +--
 include/linux/tty.h      |   16 +---------------
 5 files changed, 25 insertions(+), 41 deletions(-)
drivers/char/pty.c +1 -1
index d9c1407..c9af9ff 100644
@@ -62,7 +62,7 @@ static void pty_close(struct tty_struct *tty, struct file *filp)
 		if (tty->driver == ptm_driver)
 			devpts_pty_kill(tty->link);
 #endif
-		tty_vhangup(tty->link);
+		tty_vhangup_locked(tty->link);
 	}
 }
 
drivers/char/selection.c +2 -2
index 75889cd..ebae344 100644
@@ -313,7 +313,8 @@ int paste_selection(struct tty_struct *tty)
 	struct  tty_ldisc *ld;
 	DECLARE_WAITQUEUE(wait, current);
 
-	tty_lock_nested(); /* always called with BTM from vt_ioctl */
+	/* always called with BTM from vt_ioctl */
+	WARN_ON(!tty_locked());
 
 	acquire_console_sem();
 	poke_blanked_console();
@@ -343,6 +344,5 @@ int paste_selection(struct tty_struct *tty)
 	__set_current_state(TASK_RUNNING);
 
 	tty_ldisc_deref(ld);
-	tty_unlock();
 	return 0;
 }
drivers/char/tty_io.c +20 -21

108 lines not on this page · raw message

drivers/char/tty_ldisc.c +1 -2
index 0f49479..412f977 100644
@@ -450,9 +450,8 @@ static int tty_ldisc_open(struct tty_struct *tty, struct tty_ldisc *ld)
 	if (ld->ops->open) {
 		int ret;
                 /* BTM here locks versus a hangup event */
-		tty_lock_nested(); /* always held here already */
+		WARN_ON(!tty_locked());
 		ret = ld->ops->open(tty);
-		tty_unlock();
 		return ret;
 	}
 	return 0;
include/linux/tty.h +1 -15
index 18a7955..21a6de2 100644
@@ -416,6 +416,7 @@ extern int is_ignored(int sig);
 extern int tty_signal(int sig, struct tty_struct *tty);
 extern void tty_hangup(struct tty_struct *tty);
 extern void tty_vhangup(struct tty_struct *tty);
+extern void tty_vhangup_locked(struct tty_struct *tty);
 extern void tty_vhangup_self(void);
 extern void tty_unhangup(struct file *filp);
 extern int tty_hung_up_p(struct file *filp);
@@ -574,21 +575,6 @@ extern long vt_compat_ioctl(struct tty_struct *tty, struct file * file,
 		     unsigned int cmd, unsigned long arg);
 
 /* functions for preparation of BKL removal */
-
-/*
- * tty_lock_nested get the tty_lock while potentially holding it
- *
- * The Big TTY Mutex is a recursive lock, meaning you can take it
- * from a thread that is already holding it.
- * This is bad for a number of reasons, so tty_lock_nested should
- * really be used as rarely as possible. If a code location can
- * be shown to never get called with this held already, it should
- * use tty_lock() instead.
- */
-static inline void __lockfunc tty_lock_nested(void) __acquires(kernel_lock)
-{
-	lock_kernel();
-}
 static inline void tty_lock(void) __acquires(kernel_lock)
 {
 #ifdef CONFIG_LOCK_KERNEL
Signature · 1 line
1.7.0.4
author maintainer
#31 lore raw

PATCH 29/31 tty: implement BTM as mutex instead of BKL

In reply to Arnd Bergmann

The tty locking now follows the rules for mutexes, so we can replace the BKL usage with a new subsystem wide mutex.

This patch for now makes the new behaviour an optional experimental feature that can be enabled for testing purposes.

Using a regular mutex here will change the behaviour when blocked on the BTM from spinning to sleeping, but that should not be visible to the user.

Using the mutex also means that all the BTM is now covered by lockdep.

---
 drivers/char/Makefile    |    1 +
 drivers/char/tty_mutex.c |   47 ++++++++++++++++++++++++++++++++++++++++++++++
 include/linux/tty.h      |    8 +++++++
 lib/Kconfig.debug        |   10 +++++++++
 4 files changed, 66 insertions(+), 0 deletions(-)
 create mode 100644 drivers/char/tty_mutex.c
drivers/char/Makefile +1 -0
index 88d6eac..658bfbe 100644
@@ -9,6 +9,7 @@ FONTMAPFILE = cp437.uni
 
 obj-y	 += mem.o random.o tty_io.o n_tty.o tty_ioctl.o tty_ldisc.o tty_buffer.o tty_port.o
 
+obj-$(CONFIG_TTY_MUTEX)		+= tty_mutex.o
 obj-$(CONFIG_LEGACY_PTYS)	+= pty.o
 obj-$(CONFIG_UNIX98_PTYS)	+= pty.o
 obj-y				+= misc.o
drivers/char/tty_mutex.c new file +47 -0

47 lines not on this page · raw message

include/linux/tty.h +8 -0
index 21a6de2..3e7e04a 100644
@@ -574,7 +574,14 @@ extern int vt_ioctl(struct tty_struct *tty, struct file *file,
 extern long vt_compat_ioctl(struct tty_struct *tty, struct file * file,
 		     unsigned int cmd, unsigned long arg);
 
+/* tty_mutex.c */
 /* functions for preparation of BKL removal */
+#ifdef CONFIG_TTY_MUTEX
+extern void __lockfunc tty_lock(void) __acquires(tty_lock);
+extern void __lockfunc tty_unlock(void) __releases(tty_lock);
+extern struct task_struct *__big_tty_mutex_owner;
+#define tty_locked()		(current == __big_tty_mutex_owner)
+#else
 static inline void tty_lock(void) __acquires(kernel_lock)
 {
 #ifdef CONFIG_LOCK_KERNEL
@@ -588,6 +595,7 @@ static inline void tty_unlock(void) __releases(kernel_lock)
 	unlock_kernel();
 }
 #define tty_locked()		(kernel_locked())
+#endif
 
 /*
  * wait_event_interruptible_tty -- wait for a condition with the tty lock held
lib/Kconfig.debug +10 -0
index e722e9d..fd1a2f1 100644
@@ -428,6 +428,16 @@ config RT_MUTEX_TESTER
 	help
 	  This option enables a rt-mutex tester.
 
+config TTY_MUTEX
+	bool "Use a mutex instead of BKL for TTY locking"
+	depends on EXPERIMENTAL && SMP
+	help
+	  The TTY subsystem traditionally depends on the big kernel lock
+	  for serialization. Saying Y here replaces the BKL with the Big
+	  TTY Mutex (BTM).
+	  Building a kernel without the BKL is only possible with TTY_MUTEX
+	  enabled.
+
 config DEBUG_SPINLOCK
 	bool "Spinlock and rw-lock debugging: basic checks"
 	depends on DEBUG_KERNEL
Signature · 1 line
1.7.0.4
author maintainer
#32 lore raw

PATCH 30/31 tty: release BTM while sleeping in block_til_ready

In reply to Arnd Bergmann

Most tty drivers may block while opening a device. Since this possibly depends on another thread closing it first and both threads may need the BTM, we need to release it here.

---
 drivers/char/amiserial.c     |    2 ++
 drivers/char/ip2/ip2main.c   |    4 ++++
 drivers/char/serial167.c     |    4 +++-
 drivers/char/specialix.c     |    2 ++
 drivers/char/synclink.c      |    2 ++
 drivers/char/synclink_gt.c   |    2 ++
 drivers/char/synclinkmp.c    |    2 ++
 drivers/char/tty_port.c      |    2 ++
 drivers/serial/68328serial.c |    2 ++
 drivers/serial/68360serial.c |    2 ++
 drivers/serial/crisv10.c     |    2 ++
 11 files changed, 25 insertions(+), 1 deletions(-)
drivers/char/amiserial.c +2 -0
index 8228e61..a11c8c9 100644
@@ -1710,7 +1710,9 @@ static int block_til_ready(struct tty_struct *tty, struct file * filp,
 		printk("block_til_ready blocking: ttys%d, count = %d\n",
 		       info->line, state->count);
 #endif
+		tty_unlock();
 		schedule();
+		tty_lock();
 	}
 	__set_current_state(TASK_RUNNING);
 	remove_wait_queue(&info->open_wait, &wait);
drivers/char/ip2/ip2main.c +4 -0
index 911e1da..07f3ea3 100644
@@ -1486,7 +1486,9 @@ ip2_open( PTTY tty, struct file *pFile )
 
 	if ( tty_hung_up_p(pFile) || ( pCh->flags & ASYNC_CLOSING )) {
 		if ( pCh->flags & ASYNC_CLOSING ) {
+			tty_unlock();
 			schedule();
+			tty_lock();
 		}
 		if ( tty_hung_up_p(pFile) ) {
 			set_current_state( TASK_RUNNING );
@@ -1548,7 +1550,9 @@ ip2_open( PTTY tty, struct file *pFile )
 			rc = (( pCh->flags & ASYNC_HUP_NOTIFY ) ? -EAGAIN : -ERESTARTSYS);
 			break;
 		}
+		tty_unlock();
 		schedule();
+		tty_lock();
 	}
 	set_current_state( TASK_RUNNING );
 	remove_wait_queue(&pCh->open_wait, &wait);
drivers/char/serial167.c +3 -1
index 90b3ec0..f646725 100644
@@ -1786,7 +1786,9 @@ block_til_ready(struct tty_struct *tty, struct file *filp,
 		       tty->name, info->count);
 		/**/
 #endif
-		    schedule();
+		tty_unlock();
+		schedule();
+		tty_lock();
 	}
 	__set_current_state(TASK_RUNNING);
 	remove_wait_queue(&info->open_wait, &wait);
drivers/char/specialix.c +2 -0
index 7be456f..9f8495b 100644
@@ -1365,7 +1365,9 @@ static int block_til_ready(struct tty_struct *tty, struct file *filp,
 			retval = -ERESTARTSYS;
 			break;
 		}
+		tty_unlock();
 		schedule();
+		tty_lock();
 	}
 
 	set_current_state(TASK_RUNNING);
drivers/char/synclink.c +2 -0
index 4de1246..c1a004f 100644
@@ -3349,7 +3349,9 @@ static int block_til_ready(struct tty_struct *tty, struct file * filp,
 			printk("%s(%d):block_til_ready blocking on %s count=%d\n",
 				 __FILE__,__LINE__, tty->driver->name, port->count );
 				 
+		tty_unlock();
 		schedule();
+		tty_lock();
 	}
 	
 	set_current_state(TASK_RUNNING);
drivers/char/synclink_gt.c +2 -0
index c56b70a..99fae38 100644
@@ -3244,7 +3244,9 @@ static int block_til_ready(struct tty_struct *tty, struct file *filp,
 		}
 
 		DBGINFO(("%s block_til_ready wait\n", tty->driver->name));
+		tty_unlock();
 		schedule();
+		tty_lock();
 	}
 
 	set_current_state(TASK_RUNNING);
drivers/char/synclinkmp.c +2 -0
index cfa581e..eb58d5f 100644
@@ -3365,7 +3365,9 @@ static int block_til_ready(struct tty_struct *tty, struct file *filp,
 			printk("%s(%d):%s block_til_ready() count=%d\n",
 				 __FILE__,__LINE__, tty->driver->name, port->count );
 
+		tty_unlock();
 		schedule();
+		tty_lock();
 	}
 
 	set_current_state(TASK_RUNNING);
drivers/char/tty_port.c +2 -0
index 35eb304..33d37d2 100644
@@ -294,7 +294,9 @@ int tty_port_block_til_ready(struct tty_port *port,
 			retval = -ERESTARTSYS;
 			break;
 		}
+		tty_unlock();
 		schedule();
+		tty_lock();
 	}
 	finish_wait(&port->open_wait, &wait);
 
drivers/serial/68328serial.c +2 -0
index 3046386..0e91896 100644
@@ -1243,7 +1243,9 @@ static int block_til_ready(struct tty_struct *tty, struct file * filp,
 			retval = -ERESTARTSYS;
 			break;
 		}
+		tty_unlock();
 		schedule();
+		tty_lock();
 	}
 	current->state = TASK_RUNNING;
 	remove_wait_queue(&info->open_wait, &wait);
drivers/serial/68360serial.c +2 -0
index 5b7b801..8b8e4c3 100644
@@ -1860,7 +1860,9 @@ static int block_til_ready(struct tty_struct *tty, struct file * filp,
 		printk("block_til_ready blocking: ttys%d, count = %d\n",
 		       info->line, state->count);
 #endif
+		tty_unlock();
 		schedule();
+		tty_lock();
 	}
 	current->state = TASK_RUNNING;
 	remove_wait_queue(&info->open_wait, &wait);
drivers/serial/crisv10.c +2 -0
index 0825d4a..ca47072 100644
@@ -4055,7 +4055,9 @@ block_til_ready(struct tty_struct *tty, struct file * filp,
 		printk("block_til_ready blocking: ttyS%d, count = %d\n",
 		       info->line, info->count);
 #endif
+		tty_unlock();
 		schedule();
+		tty_lock();
 	}
 	set_current_state(TASK_RUNNING);
 	remove_wait_queue(&info->open_wait, &wait);
Signature · 1 line
1.7.0.4
author maintainer
#33 lore raw

PATCH 31/31 8250: fix set_ldisc operation

In reply to Arnd Bergmann

The ldisc number now gets passed into ->set_ldisc.

---
 drivers/serial/8250.c |    9 ++-------
 1 files changed, 2 insertions(+), 7 deletions(-)
drivers/serial/8250.c +2 -7
index 891e1dd..93c8358 100644
@@ -2409,14 +2409,9 @@ serial8250_set_termios(struct uart_port *port, struct ktermios *termios,
 }
 
 static void
-serial8250_set_ldisc(struct uart_port *port)
+serial8250_set_ldisc(struct uart_port *port, int new)
 {
-	int line = port->line;
-
-	if (line >= port->state->port.tty->driver->num)
-		return;
-
-	if (port->state->port.tty->ldisc->ops->num == N_PPS) {
+	if (new == N_PPS) {
 		port->flags |= UPF_HARDPPS_CD;
 		serial8250_enable_ms(port);
 	} else
Signature · 1 line
1.7.0.4
author maintainer
#34 lore raw
In reply to Arnd Bergmann
Quoted 6 lines · On Tuesday 01 June 2010 22:52:40 Arnd Bergmann wrote:

Hi Greg,

As promised, here is a resend of the patches from
both Alan and myself, making the BKL optional
in the TTY layer. Please apply to your tty-next
tree.

FWIW, I've documented what I've learned about the BKL (now BTM) locking in the tty code, see
http://kernelnewbies.org/BigKernelLock?action=AttachFile&do=view&target=tty_lock.png

I hope that helps in the process of killing the BTM itself.

Arnd

#35 lore raw
Quoted 8 lines · Arnd Bergmann
Quoted 6 lines · On Tuesday 01 June 2010 22:52:40 Arnd Bergmann wrote:

Hi Greg,

As promised, here is a resend of the patches from
both Alan and myself, making the BKL optional
in the TTY layer. Please apply to your tty-next
tree.

Quoted 5 lines

FWIW, I've documented what I've learned about the BKL (now BTM) locking in the tty code, see
http://kernelnewbies.org/BigKernelLock?action=AttachFile&do=view&target=tty_lock.png

I hope that helps in the process of killing the BTM itself.

Very cool, thanks for documenting this. I'll queue up your patches in a few days.

greg k-h

#36 lore raw
In reply to Arnd Bergmann
Quoted 6 lines · Arnd Bergmann

Hi Greg,

As promised, here is a resend of the patches from
both Alan and myself, making the BKL optional
in the TTY layer. Please apply to your tty-next
tree.

All applied now, thanks for doing this work.

let's see what breaks now :)

thanks,

greg k-h