Staging: comedi: fix code warnings in s626.c
PATCH 2/2 Staging: comedi: fix code warnings in s626.c
From: John Sheehan <[email protected]>
A patch for s626.c to fix some of the warnings
reported by the checkpatch.pl tool, namely,
-suspect code indent for conditional statements
-please, no space before tabs
Signed-off-by John Sheehan <[email protected]>
--- drivers/staging/comedi/drivers/s626.c | 44 ++++++++++++++++---------------- 1 files changed, 22 insertions(+), 22 deletions(-)
drivers/staging/comedi/drivers/s626.c +22 -22
@@ -816,7 +816,7 @@ static int s626_attach(struct comedi_device *dev, struct comedi_devconfig *it)MC_ENABLE (P_MC2 ,MC2_UPLD_IIC );/* Invoke command upload */ while ((RR7146 (P_MC2 ) &MC2_UPLD_IIC ) ==0 ) - ; + ;/* and wait for upload to complete. */ /* Per SAA7146 data sheet, write to STATUS reg twice to
@@ -826,7 +826,7 @@ static int s626_attach(struct comedi_device *dev, struct comedi_devconfig *it)/* Write I2C control: reset error flags. */ MC_ENABLE (P_MC2 ,MC2_UPLD_IIC );/* Invoke command upload */ while (!MC_TEST (P_MC2 ,MC2_UPLD_IIC )) - ; + ;/* and wait for upload to complete. */ }
@@ -866,14 +866,14 @@ static int s626_attach(struct comedi_device *dev, struct comedi_devconfig *it)* not start up in a defined state after a PCI reset. */ -/* PollList = EOPL; // Create a simple polling */ -/* // list for analog input */ -/* // channel 0. */ +/* PollList = EOPL; // Create a simple polling */ +/* // list for analog input */ +/* // channel 0. */ /* ResetADC( dev, &PollList ); */ /* s626_ai_rinsn(dev,dev->subdevices,NULL,data); //( &AdcData ); // */ -/* //Get initial ADC */ -/* //value. */ +/* //Get initial ADC */ +/* //value. */ /* StartVal = data[0]; */
@@ -886,10 +886,10 @@ static int s626_attach(struct comedi_device *dev, struct comedi_devconfig *it)/* for ( index = 0; index < 500; index++ ) */ /* { */ -/* s626_ai_rinsn(dev,dev->subdevices,NULL,data); */ -/* AdcData = data[0]; //ReadADC( &AdcData ); */ -/* if ( AdcData != StartVal ) */ -/* break; */ +/* s626_ai_rinsn(dev,dev->subdevices,NULL,data); */ +/* AdcData = data[0]; //ReadADC( &AdcData ); */ +/* if ( AdcData != StartVal ) */ +/* break; */ /* } */ /* end initADC */
@@ -1690,7 +1690,7 @@ static int s626_ai_insn_read(struct comedi_device *dev,/* Wait for ADC done. */ while (!(RR7146 (P_PSR ) &PSR_GPIO2 )) - ; + ;/* Fetch ADC data. */ if (n !=0 )
@@ -1723,7 +1723,7 @@ static int s626_ai_insn_read(struct comedi_device *dev,/* Wait for ADC done. */ while (!(RR7146 (P_PSR ) &PSR_GPIO2 )) - ; + ;/* Fetch ADC data from audio interface's input shift register. */
@@ -2564,11 +2564,11 @@ static uint32_t I2Chandshake(struct comedi_device *dev, uint32_t val)MC_ENABLE (P_MC2 ,MC2_UPLD_IIC );while (!MC_TEST (P_MC2 ,MC2_UPLD_IIC )) - ; + ;/* Wait until I2C bus transfer is finished or an error occurs. */ while ((RR7146 (P_I2CCTRL ) & (I2C_BUSY |I2C_ERR )) ==I2C_BUSY ) - ; + ;/* Return non-zero if I2C error occured. */ return RR7146 (P_I2CCTRL ) &I2C_ERR ;
@@ -2683,7 +2683,7 @@ static void SendDAC(struct comedi_device *dev, uint32_t val)* cleared when the transfer has finished. */ while ((RR7146 (P_MC1 ) &MC1_A2OUT ) !=0 ) - ; + ;/* START THE OUTPUT STREAM TO THE TARGET DAC -------------------- */
@@ -2701,7 +2701,7 @@ static void SendDAC(struct comedi_device *dev, uint32_t val)* to the output buffer register. */ while ((RR7146 (P_SSR ) &SSR_AF2_OUT ) ==0 ) - ; + ;/* Set up to trap execution at slot 0 when the TSL sequencer cycles * back to slot 0 after executing the EOS in slot 5. Also,
@@ -2738,7 +2738,7 @@ static void SendDAC(struct comedi_device *dev, uint32_t val)* out/in on SD2 the 0x00 that is always referenced by slot 5. */ while ((RR7146 (P_FB_BUFFER2 ) &0xFF000000 ) !=0 ) - ; + ; }/* Either (1) we were too late setting the slot 0 trap; the TSL * sequencer restarted slot 0 before we could set the EOS trap flag,
@@ -2755,7 +2755,7 @@ static void SendDAC(struct comedi_device *dev, uint32_t val)* from 0x00 to 0xFF. */ while ((RR7146 (P_FB_BUFFER2 ) &0xFF000000 ) ==0 ) - ; + ; }static void WriteMISC2 (struct comedi_device *dev,uint16_t NewImage)
@@ -2795,11 +2795,11 @@ static void DEBItransfer(struct comedi_device *dev)/* Wait for completion of upload from shadow RAM to DEBI control */ /* register. */ while (!MC_TEST (P_MC2 ,MC2_UPLD_DEBI )) - ; + ;/* Wait until DEBI transfer is done. */ while (RR7146 (P_PSR ) &PSR_DEBI_S ) - ; + ; }/* Write a value to a gate array register. */
@@ -3157,7 +3157,7 @@ static void SetLatchSource(struct comedi_device *dev, struct enc_private *k,/* * static uint16_t GetLatchSource(struct comedi_device *dev, struct enc_private *k ) * { -* return ( DEBIread( dev, k->MyCRB) >> CRBBIT_LATCHSRC ) & 3; +* return ( DEBIread( dev, k->MyCRB) >> CRBBIT_LATCHSRC ) & 3; * } */
Signature · 1 line
1.7.0.4