Skip to contentSkip to conversation

TPM bug fix causes hang on suspend (2.6.35-rc4)

PATCH Sarah Sharp 2 participants 4 messages Jul 17, 2010 – Aug 10, 2010 TPM device driver

lore
Share & tools
lore
#0 lore raw

I recently upgraded to 2.6.35-rc4, and I discovered that suspend no longer works on my Thinkpad x200s. When I suspend with some programs open (specifically while buffy is reading my maildirs), the suspend light blinks forever and the system never suspends.

I bisected the issue down to commit b5edfef, which is a merge of James Morris' security-testing-2.6 tree, that only included this commit:

commit 02a077c52ef7631275a79862ffd9f3dbe9d38bc2

Author: Rajiv Andrade <[email protected]>
Date:   Mon Jun 14 13:58:22 2010 -0300

TPM: ReadPubEK output struct fix

This patch adds a missing element of the ReadPubEK command output, that prevents future overflow of this buffer when copying the TPM output result into it.

Prevents a kernel panic in case the user tries to read the pubek from sysfs.

drivers/char/tpm/tpm.h +1 -0
index 8e00b4d..792868d 100644
@@ -224,6 +224,7 @@ struct      tpm_readpubek_params_out {
        u8      algorithm[4];
        u8      encscheme[2];
        u8      sigscheme[2];
+       __be32  paramsize;
        u8      parameters[12]; /*assuming RSA*/
        __be32  keysize;
        u8      modulus[256];

The dmesg captured over netconsole when suspend fails is attached, but it doesn't look very interesting. lspci output is also attached. I don't have any userspace programs installed that can use TPM, like trousers or libtspi1.

If I try just removing the tpm_tis, tpm_bios, and tpm modules before suspending, the suspend still fails. If I recompile without TPM hardware support (CONFIG_TCG_TPM=n), suspend still fails. However, if I also turn off the securityFS config option (CONFIG_SECURITYFS), suspend succeeds.

It looks like an odd commit to cause a suspend failure, but when I reset the git HEAD to the commit before the merge of this patch, and suspend works fine. Can you fix this?

Sarah Sharp

[  284.608553] console [netcon0] enabled
[  284.608559] netconsole: network logging started
[  292.584052] wlan0: no IPv6 routers present
[  314.124116] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0004
[  314.124138] uhci_hcd 0000:00:1a.1: port 2 portsc 008a,00
[  314.124150] hub 4-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
[  314.124154] usb 4-2: USB disconnect, address 3
[  314.124157] usb 4-2: unregistering device
[  314.124160] usb 4-2: usb_disable_device nuking all URBs
[  314.124167] usb 4-2: unregistering interface 4-2:1.0
[  314.124223] usb 4-2: unregistering interface 4-2:1.1
[  314.124266] usb 4-2: unregistering interface 4-2:1.2
[  314.124302] usb 4-2: unregistering interface 4-2:1.3

00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
Subsystem: Lenovo Device 20e0
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp

00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
Subsystem: Lenovo Device 20e4
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 45
Region 0: Memory at f2000000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 1800 [size=8]
Capabilities: <access denied>
Kernel driver in use: i915
Kernel modules: i915

00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
Subsystem: Lenovo Device 20e4
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f2400000 (64-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>

00:03.0 Communication controller: Intel Corporation Mobile 4 Series Chipset MEI Controller (rev 07)
Subsystem: Lenovo Device 20e6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f2826800 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>

00:03.2 IDE interface: Intel Corporation Mobile 4 Series Chipset PT IDER Controller (rev 07) (prog-if 85 [Master SecO PriO])

	Subsystem: Lenovo Device 20ea
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Interrupt: pin C routed to IRQ 18
	Region 0: I/O ports at 1828 [size=8]
	Region 1: I/O ports at 180c [size=4]
	Region 2: I/O ports at 1820 [size=8]
	Region 3: I/O ports at 1808 [size=4]
	Region 4: I/O ports at 1810 [size=16]
	Capabilities: <access denied>

00:03.3 Serial controller: Intel Corporation Mobile 4 Series Chipset AMT SOL Redirection (rev 07) (prog-if 02)
Subsystem: Lenovo Device 20ec
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 1830 [size=8]
Region 1: Memory at f2624000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: serial

00:19.0 Ethernet controller: Intel Corporation 82567LM Gigabit Network Connection (rev 03)
Subsystem: Lenovo Device 20ee
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 44
Region 0: Memory at f2600000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at f2625000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at 1840 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e

00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03)
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 1860 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03)
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 1880 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03)
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 4: I/O ports at 18a0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) (prog-if 20)
Subsystem: Lenovo Device 20f1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 23
Region 0: Memory at f2826c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd

00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03)
Subsystem: Lenovo Device 20f2
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 46
Region 0: Memory at f2620000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel

00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: c0000000-c01fffff
Prefetchable memory behind bridge: 00000000c0200000-00000000c03fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: f2500000-f25fffff
Prefetchable memory behind bridge: 00000000c0400000-00000000c05fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=0c, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f0000000-f1ffffff
Prefetchable memory behind bridge: 00000000f2900000-00000000f29fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
Kernel modules: shpchp

00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03)
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at 18c0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03)
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at 18e0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03)
Subsystem: Lenovo Device 20f0
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1c00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) (prog-if 20)
Subsystem: Lenovo Device 20f1
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 0: Memory at f2827000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) (prog-if 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=0d, subordinate=0d, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>

00:1f.0 ISA bridge: Intel Corporation ICH9M-E LPC Interface Controller (rev 03)
Subsystem: Lenovo Device 20f5
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: iTCO_wdt

00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) (prog-if 01)

	Subsystem: Lenovo Device 20f8
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin B routed to IRQ 43
	Region 0: I/O ports at 1c48 [size=8]
	Region 1: I/O ports at 183c [size=4]
	Region 2: I/O ports at 1c40 [size=8]
	Region 3: I/O ports at 1838 [size=4]
	Region 4: I/O ports at 1c20 [size=32]
	Region 5: Memory at f2826000 (32-bit, non-prefetchable) [size=2K]
	Capabilities: <access denied>
	Kernel driver in use: ahci

00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03)
Subsystem: Lenovo Device 20f9
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 0: Memory at f2827400 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 1c60 [size=32]
Kernel modules: i2c-i801

03:00.0 Network controller: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection
Subsystem: Intel Corporation Device 1211
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 47
Region 0: Memory at f2500000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: iwlagn
Kernel modules: iwlagn

#1 lore raw

Am Freitag, den 16.07.2010, 17:00 -0700 schrieb Sarah Sharp:

Quoted 48 lines

I recently upgraded to 2.6.35-rc4, and I discovered that suspend no longer works on my Thinkpad x200s. When I suspend with some programs open (specifically while buffy is reading my maildirs), the suspend light blinks forever and the system never suspends.

I bisected the issue down to commit b5edfef, which is a merge of James Morris' security-testing-2.6 tree, that only included this commit:

commit 02a077c52ef7631275a79862ffd9f3dbe9d38bc2

Author: Rajiv Andrade <[email protected]>
Date:   Mon Jun 14 13:58:22 2010 -0300

TPM: ReadPubEK output struct fix

This patch adds a missing element of the ReadPubEK command output, that prevents future overflow of this buffer when copying the TPM output result into it.

Prevents a kernel panic in case the user tries to read the pubek from sysfs.

drivers/char/tpm/tpm.h +1 -0
index 8e00b4d..792868d 100644
@@ -224,6 +224,7 @@ struct      tpm_readpubek_params_out {
        u8      algorithm[4];
        u8      encscheme[2];
        u8      sigscheme[2];
+       __be32  paramsize;
        u8      parameters[12]; /*assuming RSA*/
        __be32  keysize;
        u8      modulus[256];

The dmesg captured over netconsole when suspend fails is attached, but it doesn't look very interesting. lspci output is also attached. I don't have any userspace programs installed that can use TPM, like trousers or libtspi1.

If I try just removing the tpm_tis, tpm_bios, and tpm modules before suspending, the suspend still fails. If I recompile without TPM hardware support (CONFIG_TCG_TPM=n), suspend still fails. However, if I also turn off the securityFS config option (CONFIG_SECURITYFS), suspend succeeds.

Quoted 5 lines

It looks like an odd commit to cause a suspend failure, but when I reset the git HEAD to the commit before the merge of this patch, and suspend works fine. Can you fix this?

Sarah Sharp

Maybe same as https://bugzilla.kernel.org/show_bug.cgi?id=16256 ?

#2 lore raw
Quoted 49 lines · Thomas Meyer

Am Freitag, den 16.07.2010, 17:00 -0700 schrieb Sarah Sharp:

Quoted 48 lines

I recently upgraded to 2.6.35-rc4, and I discovered that suspend no longer works on my Thinkpad x200s. When I suspend with some programs open (specifically while buffy is reading my maildirs), the suspend light blinks forever and the system never suspends.

I bisected the issue down to commit b5edfef, which is a merge of James Morris' security-testing-2.6 tree, that only included this commit:

commit 02a077c52ef7631275a79862ffd9f3dbe9d38bc2

Author: Rajiv Andrade <[email protected]>
Date:   Mon Jun 14 13:58:22 2010 -0300

TPM: ReadPubEK output struct fix

This patch adds a missing element of the ReadPubEK command output, that prevents future overflow of this buffer when copying the TPM output result into it.

Prevents a kernel panic in case the user tries to read the pubek from sysfs.

drivers/char/tpm/tpm.h +1 -0
index 8e00b4d..792868d 100644
@@ -224,6 +224,7 @@ struct      tpm_readpubek_params_out {
        u8      algorithm[4];
        u8      encscheme[2];
        u8      sigscheme[2];
+       __be32  paramsize;
        u8      parameters[12]; /*assuming RSA*/
        __be32  keysize;
        u8      modulus[256];

The dmesg captured over netconsole when suspend fails is attached, but it doesn't look very interesting. lspci output is also attached. I don't have any userspace programs installed that can use TPM, like trousers or libtspi1.

If I try just removing the tpm_tis, tpm_bios, and tpm modules before suspending, the suspend still fails. If I recompile without TPM hardware support (CONFIG_TCG_TPM=n), suspend still fails. However, if I also turn off the securityFS config option (CONFIG_SECURITYFS), suspend succeeds.

Quoted 7 lines
Quoted 5 lines

It looks like an odd commit to cause a suspend failure, but when I reset the git HEAD to the commit before the merge of this patch, and suspend works fine. Can you fix this?

Sarah Sharp

Maybe same as https://bugzilla.kernel.org/show_bug.cgi?id=16256 ?

That doesn't look really similar. The user found a different patch at fault, and they were also able to successfully suspend when the tpm_tis module was removed, but suspend still breaks for me in that case. Suspend breaks with that commit even when I don't compile any tpm modules at all. But I'll try Helmut's fix[1] and let you know if it works.

Sarah Sharp

[1] http://sourceforge.net/mailarchive/message.php?msg_name=201006091511.09810.helmut.schaa%40googlemail.com

#3 lore raw
Quoted 58 lines · Sarah Sharp
Quoted 49 lines · Thomas Meyer

Am Freitag, den 16.07.2010, 17:00 -0700 schrieb Sarah Sharp:

Quoted 48 lines

I recently upgraded to 2.6.35-rc4, and I discovered that suspend no longer works on my Thinkpad x200s. When I suspend with some programs open (specifically while buffy is reading my maildirs), the suspend light blinks forever and the system never suspends.

I bisected the issue down to commit b5edfef, which is a merge of James Morris' security-testing-2.6 tree, that only included this commit:

commit 02a077c52ef7631275a79862ffd9f3dbe9d38bc2

Author: Rajiv Andrade <[email protected]>
Date:   Mon Jun 14 13:58:22 2010 -0300

TPM: ReadPubEK output struct fix

This patch adds a missing element of the ReadPubEK command output, that prevents future overflow of this buffer when copying the TPM output result into it.

Prevents a kernel panic in case the user tries to read the pubek from sysfs.

drivers/char/tpm/tpm.h +1 -0
index 8e00b4d..792868d 100644
@@ -224,6 +224,7 @@ struct      tpm_readpubek_params_out {
        u8      algorithm[4];
        u8      encscheme[2];
        u8      sigscheme[2];
+       __be32  paramsize;
        u8      parameters[12]; /*assuming RSA*/
        __be32  keysize;
        u8      modulus[256];

The dmesg captured over netconsole when suspend fails is attached, but it doesn't look very interesting. lspci output is also attached. I don't have any userspace programs installed that can use TPM, like trousers or libtspi1.

If I try just removing the tpm_tis, tpm_bios, and tpm modules before suspending, the suspend still fails. If I recompile without TPM hardware support (CONFIG_TCG_TPM=n), suspend still fails. However, if I also turn off the securityFS config option (CONFIG_SECURITYFS), suspend succeeds.

Quoted 7 lines
Quoted 5 lines

It looks like an odd commit to cause a suspend failure, but when I reset the git HEAD to the commit before the merge of this patch, and suspend works fine. Can you fix this?

Sarah Sharp

Maybe same as https://bugzilla.kernel.org/show_bug.cgi?id=16256 ?

Quoted 6 lines

That doesn't look really similar. The user found a different patch at fault, and they were also able to successfully suspend when the tpm_tis module was removed, but suspend still breaks for me in that case. Suspend breaks with that commit even when I don't compile any tpm modules at all. But I'll try Helmut's fix[1] and let you know if it works.

I tried the fix, and all seemed well for a while. Then suspend randomly broken again. I've tried to update to 2.6.35, but I have the same issue (constant blinking suspend light and the suspend never completes).

Sarah Sharp