ASoC: Add iPAQ RX1950 support
Subsystems (4)
v6 cover ASoC: Add iPAQ RX1950 support
These three patches are necessary to add sound support for iPAQ RX1950 PDA, appropriate mach-rx1950.c patch is missing, as it depends on battery and LEDs patches which are still not merged nor reviewed.
First patch improves situation with power consumption for uda1380 and also fixes suspend/resume.
Second patch just adds glue driver.
Third patch fixes s3c_device_iis name and exports s3c_device_pcm for all s3c24xx-based devices.
v2: - make mixer regs dirty after power-down, not after power-up
v3: - improve glue driver init code (handle errors)
v4: - adapt patches for multi-component
v5: - handle return values in rx1950_uda1380 init code;
- use gpio_set_value instead of gpio_direction_output in spk_power;
- uda1380: improve code alignment in set_bias
v6: - use gpio_is_valid to check gpio validity
PATCH RESEND v6 1/3 ASoC: uda1380: make driver more powersave-friendly
Disable some codec modules in standby mode, completely disable codec in off mode to save some power.
Fix suspend/resume: mark mixer regs as dirty on resume to restore mixer values, otherwise driver produces no sound (master is muted by default).
--- sound/soc/codecs/uda1380.c | 145 ++++++++++++++++++++++++++++++++------------ 1 files changed, 105 insertions(+), 40 deletions(-)
sound/soc/codecs/uda1380.c +105 -40
@@ -39,6 +39,7 @@ struct uda1380_priv {u16 reg_cache[UDA1380_CACHEREGNUM ];unsigned int dac_clk;struct work_struct work; +void *control_data; };/*
@@ -129,7 +130,46 @@ static int uda1380_write(struct snd_soc_codec *codec, unsigned int reg,return -EIO ; } -#define uda1380_reset (c) uda1380_write(c, UDA1380_RESET, 0) +static void uda1380_sync_cache (struct snd_soc_codec *codec) +{ +int reg; +u8 data[3 ]; +u16 *cache = codec->reg_cache; + +/* Sync reg_cache with the hardware */ +for (reg =0 ; reg <UDA1380_MVOL ; reg++) { + data[0 ] = reg; + data[1 ] = (cache[reg] &0xff00 ) >>8 ; + data[2 ] = cache[reg] &0x00ff ; +if (codec->hw_write (codec->control_data, data,3 ) !=3 ) +dev_err (codec->dev,"%s: write to reg 0x%x failed\n" , + __func__, reg); + } +} + +static int uda1380_reset (struct snd_soc_codec *codec) +{ +struct uda1380_platform_data *pdata = codec->dev->platform_data; + +if (gpio_is_valid (pdata->gpio_reset)) { +gpio_set_value (pdata->gpio_reset,1 ); +mdelay (1 ); +gpio_set_value (pdata->gpio_reset,0 ); + }else { +u8 data[3 ]; + + data[0 ] =UDA1380_RESET ; + data[1 ] =0 ; + data[2 ] =0 ; + +if (codec->hw_write (codec->control_data, data,3 ) !=3 ) { +dev_err (codec->dev,"%s: failed\n" , __func__); +return -EIO ; + } + } + +return 0 ; +}static void uda1380_flush_work (struct work_struct *work) {
@@ -560,18 +600,40 @@ static int uda1380_set_bias_level(struct snd_soc_codec *codec, enum snd_soc_bias_level level) {int pm =uda1380_read_reg_cache (codec,UDA1380_PM ); +int reg; +struct uda1380_platform_data *pdata = codec->dev->platform_data; + +if (codec->bias_level == level) +return 0 ;switch (level) {case SND_SOC_BIAS_ON :case SND_SOC_BIAS_PREPARE : +/* ADC, DAC on */ uda1380_write (codec,UDA1380_PM ,R02_PON_BIAS | pm);break ;case SND_SOC_BIAS_STANDBY : -uda1380_write (codec,UDA1380_PM ,R02_PON_BIAS ); -break ; -case SND_SOC_BIAS_OFF : +if (codec->bias_level ==SND_SOC_BIAS_OFF ) { +if (gpio_is_valid (pdata->gpio_power)) { +gpio_set_value (pdata->gpio_power,1 ); +uda1380_reset (codec); + } + +uda1380_sync_cache (codec); + }uda1380_write (codec,UDA1380_PM ,0x0 );break ; +case SND_SOC_BIAS_OFF : +if (!gpio_is_valid (pdata->gpio_power)) +break ; + +gpio_set_value (pdata->gpio_power,0 ); + +/* Mark mixer regs cache dirty to sync them with +* codec regs on power on. +*/ +for (reg =UDA1380_MVOL ; reg <UDA1380_CACHEREGNUM ; reg++) +set_bit (reg -0x10 , &uda1380_cache_dirty); } codec->bias_level = level;return 0 ;
@@ -651,16 +713,6 @@ static int uda1380_suspend(struct snd_soc_codec *codec, pm_message_t state)static int uda1380_resume (struct snd_soc_codec *codec) { -int i; -u8 data[2 ]; -u16 *cache = codec->reg_cache; - -/* Sync reg_cache with the hardware */ -for (i =0 ; i <ARRAY_SIZE (uda1380_reg); i++) { - data[0 ] = (i <<1 ) | ((cache[i] >>8 ) &0x0001 ); - data[1 ] = cache[i] &0x00ff ; - codec->hw_write (codec->control_data, data,2 ); - }uda1380_set_bias_level (codec,SND_SOC_BIAS_STANDBY );return 0 ; }
@@ -671,29 +723,36 @@ static int uda1380_probe(struct snd_soc_codec *codec)struct uda1380_priv *uda1380 =snd_soc_codec_get_drvdata (codec);int ret; + uda1380->codec = codec; + codec->hw_write = (hw_write_t )i2c_master_send; + codec->control_data = uda1380->control_data; -if (!pdata || !pdata->gpio_power || !pdata->gpio_reset) +if (!pdata)return -EINVAL ; - ret =gpio_request (pdata->gpio_power,"uda1380 power" ); -if (ret) -return ret; - ret =gpio_request (pdata->gpio_reset,"uda1380 reset" ); -if (ret) - goto err_gpio; - -gpio_direction_output (pdata->gpio_power,1 ); - -/* we may need to have the clock running here - pH5 */ -gpio_direction_output (pdata->gpio_reset,1 ); -udelay (5 ); -gpio_set_value (pdata->gpio_reset,0 ); +if (gpio_is_valid (pdata->gpio_reset)) { + ret =gpio_request (pdata->gpio_reset,"uda1380 reset" ); +if (ret) + goto err_out; + ret =gpio_direction_output (pdata->gpio_reset,0 ); +if (ret) + goto err_gpio_reset_conf; + } - ret =uda1380_reset (codec); -if (ret <0 ) { -dev_err (codec->dev,"Failed to issue reset\n" ); - goto err_reset; +if (gpio_is_valid (pdata->gpio_power)) { + ret =gpio_request (pdata->gpio_power,"uda1380 power" ); +if (ret) + goto err_gpio; + ret =gpio_direction_output (pdata->gpio_power,0 ); +if (ret) + goto err_gpio_power_conf; + }else { + ret =uda1380_reset (codec); +if (ret) { +dev_err (codec->dev,"Failed to issue reset\n" ); + goto err_reset; + } }INIT_WORK (&uda1380->work, uda1380_flush_work);
@@ -703,10 +762,11 @@ static int uda1380_probe(struct snd_soc_codec *codec)/* set clock input */ switch (pdata->dac_clk) {case UDA1380_DAC_CLK_SYSCLK : -uda1380_write (codec,UDA1380_CLK ,0 ); +uda1380_write_reg_cache (codec,UDA1380_CLK ,0 );break ;case UDA1380_DAC_CLK_WSPLL : -uda1380_write (codec,UDA1380_CLK ,R00_DAC_CLK ); +uda1380_write_reg_cache (codec,UDA1380_CLK , +R00_DAC_CLK );break ; }
@@ -717,10 +777,15 @@ static int uda1380_probe(struct snd_soc_codec *codec)return 0 ; err_reset: -gpio_set_value (pdata->gpio_power,0 ); -gpio_free (pdata->gpio_reset); +err_gpio_power_conf: +if (gpio_is_valid (pdata->gpio_power)) +gpio_free (pdata->gpio_power); + +err_gpio_reset_conf: err_gpio: -gpio_free (pdata->gpio_power); +if (gpio_is_valid (pdata->gpio_reset)) +gpio_free (pdata->gpio_reset); +err_out:return ret; }
@@ -731,7 +796,6 @@ static int uda1380_remove(struct snd_soc_codec *codec)uda1380_set_bias_level (codec,SND_SOC_BIAS_OFF ); -gpio_set_value (pdata->gpio_power,0 );gpio_free (pdata->gpio_reset);gpio_free (pdata->gpio_power);
@@ -743,8 +807,8 @@ static struct snd_soc_codec_driver soc_codec_dev_uda1380 = { .remove = uda1380_remove, .suspend = uda1380_suspend, .resume = uda1380_resume, - .read = uda1380_read_reg_cache, - .write = uda1380_write, + .read = uda1380_read_reg_cache, + .write = uda1380_write, .set_bias_level = uda1380_set_bias_level, .reg_cache_size = ARRAY_SIZE(uda1380_reg), .reg_word_size = sizeof(u16),
@@ -764,6 +828,7 @@ static __devinit int uda1380_i2c_probe(struct i2c_client *i2c,return -ENOMEM ;i2c_set_clientdata (i2c, uda1380); + uda1380->control_data = i2c; ret =snd_soc_register_codec (&i2c->dev, &soc_codec_dev_uda1380, uda1380_dai,ARRAY_SIZE (uda1380_dai));
Signature · 1 line
1.7.2
Re: [PATCH RESEND v6 1/3] ASoC: uda1380: make driver more powersave-friendly
Dne Po 30. srpna 2010 10:28:07 Vasily Khoruzhick napsal(a):
Quoted 7 lines
Disable some codec modules in standby mode, completely disable codec in off mode to save some power.
Fix suspend/resume: mark mixer regs as dirty on resume to restore mixer values, otherwise driver produces no sound (master is muted by default).Signed-off-by Vasily Khoruzhick <[email protected]>
Please have my:
Quoted 235 lines
--- sound/soc/codecs/uda1380.c | 145++++++++++++++++++++++++++++++++------------ 1 files changed, 105 insertions(+), 40 deletions(-)
sound/soc/codecs/uda1380.c +66
-14@@ -39,6 +39,7 @@ struct uda1380_priv {u16 reg_cache[UDA1380_CACHEREGNUM ];unsigned int dac_clk;struct work_struct work; +void *control_data; };/* @@ -129,7 +130,46 @@ static int uda1380_write(struct snd_soc_codec *codec, unsigned int reg, return -EIO; } -#define uda1380_reset (c) uda1380_write(c, UDA1380_RESET, 0) +static void uda1380_sync_cache (struct snd_soc_codec *codec) +{ +int reg; +u8 data[3 ]; +u16 *cache = codec->reg_cache; + +/* Sync reg_cache with the hardware */ +for (reg =0 ; reg <UDA1380_MVOL ; reg++) { + data[0 ] = reg; + data[1 ] = (cache[reg] &0xff00 ) >>8 ; + data[2 ] = cache[reg] &0x00ff ; +if (codec->hw_write (codec->control_data, data,3 ) !=3 ) +dev_err (codec->dev,"%s: write to reg 0x%x failed\n" , + __func__, reg); + } +} + +static int uda1380_reset (struct snd_soc_codec *codec) +{ +struct uda1380_platform_data *pdata = codec->dev->platform_data; + +if (gpio_is_valid (pdata->gpio_reset)) { +gpio_set_value (pdata->gpio_reset,1 ); +mdelay (1 ); +gpio_set_value (pdata->gpio_reset,0 ); + }else { +u8 data[3 ]; + + data[0 ] =UDA1380_RESET ; + data[1 ] =0 ; + data[2 ] =0 ; + +if (codec->hw_write (codec->control_data, data,3 ) !=3 ) { +dev_err (codec->dev,"%s: failed\n" , __func__); +return -EIO ; + } + } + +return 0 ; +}static void uda1380_flush_work (struct work_struct *work) {@@ -560,18 +600,40 @@ static int uda1380_set_bias_level(struct snd_soc_codec *codec, enum snd_soc_bias_level level) { int pm = uda1380_read_reg_cache(codec, UDA1380_PM); +int reg; +struct uda1380_platform_data *pdata = codec->dev->platform_data; + +if (codec->bias_level == level) +return 0 ;switch (level) {case SND_SOC_BIAS_ON :case SND_SOC_BIAS_PREPARE : +/* ADC, DAC on */ uda1380_write (codec,UDA1380_PM ,R02_PON_BIAS | pm);break ;case SND_SOC_BIAS_STANDBY : -uda1380_write (codec,UDA1380_PM ,R02_PON_BIAS ); -break ; -case SND_SOC_BIAS_OFF : +if (codec->bias_level ==SND_SOC_BIAS_OFF ) { +if (gpio_is_valid (pdata->gpio_power)) { +gpio_set_value (pdata->gpio_power,1 ); +uda1380_reset (codec); + } + +uda1380_sync_cache (codec); + }uda1380_write (codec,UDA1380_PM ,0x0 );break ; +case SND_SOC_BIAS_OFF : +if (!gpio_is_valid (pdata->gpio_power)) +break ; + +gpio_set_value (pdata->gpio_power,0 ); + +/* Mark mixer regs cache dirty to sync them with +* codec regs on power on. +*/ +for (reg =UDA1380_MVOL ; reg <UDA1380_CACHEREGNUM ; reg++) +set_bit (reg -0x10 , &uda1380_cache_dirty); } codec->bias_level = level;return 0 ;@@ -651,16 +713,6 @@ static int uda1380_suspend(struct snd_soc_codec *codec, pm_message_t state)static int uda1380_resume (struct snd_soc_codec *codec) { -int i; -u8 data[2 ]; -u16 *cache = codec->reg_cache; - -/* Sync reg_cache with the hardware */ -for (i =0 ; i <ARRAY_SIZE (uda1380_reg); i++) { - data[0 ] = (i <<1 ) | ((cache[i] >>8 ) &0x0001 ); - data[1 ] = cache[i] &0x00ff ; - codec->hw_write (codec->control_data, data,2 ); - }uda1380_set_bias_level (codec,SND_SOC_BIAS_STANDBY );return 0 ;}
sound/soc/codecs/uda1380.c +38
-26@@ -671,29 +723,36 @@ static int uda1380_probe(struct snd_soc_codec *codec)struct uda1380_priv *uda1380 =snd_soc_codec_get_drvdata (codec);int ret; + uda1380->codec = codec; + codec->hw_write = (hw_write_t )i2c_master_send; + codec->control_data = uda1380->control_data; -if (!pdata || !pdata->gpio_power || !pdata->gpio_reset) +if (!pdata)return -EINVAL ; - ret =gpio_request (pdata->gpio_power,"uda1380 power" ); -if (ret) -return ret; - ret =gpio_request (pdata->gpio_reset,"uda1380 reset" ); -if (ret) - goto err_gpio; - -gpio_direction_output (pdata->gpio_power,1 ); - -/* we may need to have the clock running here - pH5 */ -gpio_direction_output (pdata->gpio_reset,1 ); -udelay (5 ); -gpio_set_value (pdata->gpio_reset,0 ); +if (gpio_is_valid (pdata->gpio_reset)) { + ret =gpio_request (pdata->gpio_reset,"uda1380 reset" ); +if (ret) + goto err_out; + ret =gpio_direction_output (pdata->gpio_reset,0 ); +if (ret) + goto err_gpio_reset_conf; + } - ret =uda1380_reset (codec); -if (ret <0 ) { -dev_err (codec->dev,"Failed to issue reset\n" ); - goto err_reset; +if (gpio_is_valid (pdata->gpio_power)) { + ret =gpio_request (pdata->gpio_power,"uda1380 power" ); +if (ret) + goto err_gpio; + ret =gpio_direction_output (pdata->gpio_power,0 ); +if (ret) + goto err_gpio_power_conf; + }else { + ret =uda1380_reset (codec); +if (ret) { +dev_err (codec->dev,"Failed to issue reset\n" ); + goto err_reset; + } }INIT_WORK (&uda1380->work, uda1380_flush_work);@@ -703,10 +762,11 @@ static int uda1380_probe(struct snd_soc_codec *codec)/* set clock input */ switch (pdata->dac_clk) {case UDA1380_DAC_CLK_SYSCLK : -uda1380_write (codec,UDA1380_CLK ,0 ); +uda1380_write_reg_cache (codec,UDA1380_CLK ,0 );break ;case UDA1380_DAC_CLK_WSPLL : -uda1380_write (codec,UDA1380_CLK ,R00_DAC_CLK ); +uda1380_write_reg_cache (codec,UDA1380_CLK , +R00_DAC_CLK );break ; }@@ -717,10 +777,15 @@ static int uda1380_probe(struct snd_soc_codec *codec)return 0 ; err_reset: -gpio_set_value (pdata->gpio_power,0 ); -gpio_free (pdata->gpio_reset); +err_gpio_power_conf: +if (gpio_is_valid (pdata->gpio_power)) +gpio_free (pdata->gpio_power); + +err_gpio_reset_conf: err_gpio: -gpio_free (pdata->gpio_power); +if (gpio_is_valid (pdata->gpio_reset)) +gpio_free (pdata->gpio_reset); +err_out:return ret; }@@ -731,7 +796,6 @@ static int uda1380_remove(struct snd_soc_codec *codec)uda1380_set_bias_level (codec,SND_SOC_BIAS_OFF ); -gpio_set_value (pdata->gpio_power,0 );gpio_free (pdata->gpio_reset);gpio_free (pdata->gpio_power);@@ -743,8 +807,8 @@ static struct snd_soc_codec_driver soc_codec_dev_uda1380 = { .remove = uda1380_remove, .suspend = uda1380_suspend, .resume = uda1380_resume, - .read = uda1380_read_reg_cache, - .write = uda1380_write, + .read = uda1380_read_reg_cache, + .write = uda1380_write, .set_bias_level = uda1380_set_bias_level, .reg_cache_size = ARRAY_SIZE(uda1380_reg), .reg_word_size = sizeof(u16),
sound/soc/codecs/uda1380.c static __devinit int uda1380_i2c_probe(struct · line 834
Quoted 7 lines
sound/soc/codecs/uda1380.c +1
-0@@ -764,6 +828,7 @@ static __devinit int uda1380_i2c_probe(struct i2c_client *i2c, return -ENOMEM ;i2c_set_clientdata (i2c, uda1380); + uda1380->control_data = i2c; ret = snd_soc_register_codec(&i2c->dev, &soc_codec_dev_uda1380, uda1380_dai,
ARRAY_SIZE(uda1380_dai));
Re: [PATCH RESEND v6 1/3] ASoC: uda1380: make driver more powersave-friendly
В сообщении от 30 августа 2010 11:43:22 автор Marek Vasut написал:
Quoted 7 lines
Dne Po 30. srpna 2010 10:28:07 Vasily Khoruzhick napsal(a):
Quoted 6 lines
Disable some codec modules in standby mode, completely disable codec in off mode to save some power.
Fix suspend/resume: mark mixer regs as dirty on resume to restore mixer values, otherwise driver produces no sound (master is muted by default).
Quoted 5 lines
Quoted 1 line
Signed-off-by Vasily Khoruzhick <[email protected]>Please have my:
Acked-by Marek Vasut <[email protected]>
Does it mean I should resend patches with this line included? :)
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
Re: [PATCH RESEND v6 1/3] ASoC: uda1380: make driver more powersave-friendly
Quoted 8 lines · Vasily Khoruzhick
В сообщении от 30 августа 2010 11:43:22 автор Marek Vasut написал:
Quoted 7 lines
Dne Po 30. srpna 2010 10:28:07 Vasily Khoruzhick napsal(a):
Quoted 6 lines
Disable some codec modules in standby mode, completely disable codec in off mode to save some power.
Fix suspend/resume: mark mixer regs as dirty on resume to restore mixer values, otherwise driver produces no sound (master is muted by default).
Quoted 7 lines
Quoted 5 lines
Quoted 1 line
Signed-off-by Vasily Khoruzhick <[email protected]>Please have my:
Acked-by Marek Vasut <[email protected]>Does it mean I should resend patches with this line included? :)
No.
Signature · 8 lines
Freelance Developer, SlimLogic Ltd ASoC and Voltage Regulator Maintainer. http://www.slimlogic.co.uk _______________________________________________ Alsa-devel mailing list [email protected] http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
PATCH RESEND v6 2/3 ASoC: Add HP iPAQ RX1950 support
In reply to Vasily Khoruzhick--- sound/soc/s3c24xx/Kconfig | 8 + sound/soc/s3c24xx/Makefile | 2 + sound/soc/s3c24xx/rx1950_uda1380.c | 335 ++++++++++++++++++++++++++++++++++++ 3 files changed, 345 insertions(+), 0 deletions(-) create mode 100644 sound/soc/s3c24xx/rx1950_uda1380.c
sound/soc/s3c24xx/Kconfig +8 -0
@@ -118,6 +118,14 @@ config SND_S3C24XX_SOC_SIMTEC_HERMES select SND_SOC_TLV320AIC3X select SND_S3C24XX_SOC_SIMTEC +config SND_S3C24XX_SOC_RX1950_UDA1380 + tristate "Audio support for the HP iPAQ RX1950" + depends on SND_S3C24XX_SOC && MACH_RX1950 + select SND_S3C24XX_SOC_I2S + select SND_SOC_UDA1380 + help + This driver provides audio support for HP iPAQ RX1950 PDA. + config SND_SOC_SMDK_WM9713 tristate "SoC AC97 Audio support for SMDK with WM9713" depends on SND_S3C24XX_SOC && (MACH_SMDK6410 || MACH_SMDKC100 || MACH_SMDKV210 || MACH_SMDKC110)
sound/soc/s3c24xx/Makefile +2 -0
@@ -27,6 +27,7 @@ snd-soc-s3c24xx-uda134x-objs := s3c24xx_uda134x.o snd-soc-s3c24xx-simtec-objs := s3c24xx_simtec.o snd-soc-s3c24xx-simtec-hermes-objs := s3c24xx_simtec_hermes.o snd-soc-s3c24xx-simtec-tlv320aic23-objs := s3c24xx_simtec_tlv320aic23.o +snd-soc-rx1950-uda1380-objs := rx1950_uda1380.o snd-soc-smdk64xx-wm8580-objs := smdk64xx_wm8580.o snd-soc-smdk-wm9713-objs := smdk_wm9713.o snd-soc-s3c64xx-smartq-wm8987-objs := smartq_wm8987.o
@@ -42,6 +43,7 @@ obj-$(CONFIG_SND_S3C24XX_SOC_S3C24XX_UDA134X) += snd-soc-s3c24xx-uda134x.o obj-$(CONFIG_SND_S3C24XX_SOC_SIMTEC) += snd-soc-s3c24xx-simtec.o obj-$(CONFIG_SND_S3C24XX_SOC_SIMTEC_HERMES) += snd-soc-s3c24xx-simtec-hermes.o obj-$(CONFIG_SND_S3C24XX_SOC_SIMTEC_TLV320AIC23) += snd-soc-s3c24xx-simtec-tlv320aic23.o +obj-$(CONFIG_SND_S3C24XX_SOC_RX1950_UDA1380) += snd-soc-rx1950-uda1380.o obj-$(CONFIG_SND_S3C64XX_SOC_WM8580) += snd-soc-smdk64xx-wm8580.o obj-$(CONFIG_SND_SOC_SMDK_WM9713) += snd-soc-smdk-wm9713.o obj-$(CONFIG_SND_S3C64XX_SOC_SMARTQ) += snd-soc-s3c64xx-smartq-wm8987.o
sound/soc/s3c24xx/rx1950_uda1380.c new file +335 -0
335 lines not on this page · raw message
Signature · 1 line
1.7.2
PATCH RESEND v6 3/3 ARM: S3C24XX: I2S multi-component-related fixes
In reply to Vasily KhoruzhickExport s3c_device_pcm for all S3C24xx-devices, not only for S3C2440;
Fix device name for s3c_device_iis;
--- arch/arm/plat-s3c24xx/devs.c | 32 ++++++++++++++++---------------- 1 files changed, 16 insertions(+), 16 deletions(-)
arch/arm/plat-s3c24xx/devs.c +16 -16
@@ -247,7 +247,7 @@ static struct resource s3c_iis_resource[] = {static u64 s3c_device_iis_dmamask =0xffffffffUL ;struct platform_device s3c_device_iis = { - .name ="s3c2410-iis" , + .name ="s3c24xx-iis" , .id =-1 , .num_resources =ARRAY_SIZE (s3c_iis_resource), .resource = s3c_iis_resource,
@@ -259,6 +259,21 @@ struct platform_device s3c_device_iis = {EXPORT_SYMBOL (s3c_device_iis); +/* ASoC PCM DMA */ + +static u64 s3c_device_audio_dmamask =0xffffffffUL ; + +struct platform_device s3c_device_pcm = { + .name ="s3c24xx-pcm-audio" , + .id =-1 , + .dev = { + .dma_mask = &s3c_device_audio_dmamask, + .coherent_dma_mask =0xffffffffUL + } +}; + +EXPORT_SYMBOL (s3c_device_pcm); +/* RTC */ static struct resource s3c_rtc_resource[] = {
@@ -481,8 +496,6 @@ static struct resource s3c_ac97_resource[] = { }, }; -static u64 s3c_device_audio_dmamask =0xffffffffUL ; -struct platform_device s3c_device_ac97 = { .name ="s3c-ac97" , .id =-1 ,
@@ -496,19 +509,6 @@ struct platform_device s3c_device_ac97 = {EXPORT_SYMBOL (s3c_device_ac97); -/* ASoC PCM DMA */ - -struct platform_device s3c_device_pcm = { - .name ="s3c24xx-pcm-audio" , - .id =-1 , - .dev = { - .dma_mask = &s3c_device_audio_dmamask, - .coherent_dma_mask =0xffffffffUL - } -}; - -EXPORT_SYMBOL (s3c_device_pcm); -/* ASoC I2S */ struct platform_device s3c2412_device_iis = {
Signature · 1 line
1.7.2
Quoted 13 lines · Vasily Khoruzhick
These three patches are necessary to add sound support for iPAQ RX1950 PDA, appropriate
mach-rx1950.cpatch is missing, as it depends on battery and LEDs patches which are still not merged nor reviewed.First patch improves situation with power consumption for uda1380 and also fixes suspend/resume.
Second patch just adds glue driver.
Third patch fixes
s3c_device_iisname and exportss3c_device_pcmfor all s3c24xx-based devices.
Quoted 8 lines
v2: - make mixer regs dirty after power-down, not after power-up
v3: - improve glue driver init code (handle errors)
v4: - adapt patches for multi-component
v5: - handle return values inrx1950_uda1380init code;
- usegpio_set_valueinstead ofgpio_direction_outputinspk_power;
- uda1380: improve code alignment inset_bias
v6: - usegpio_is_validto check gpio validity
All
Signature · 3 lines
Freelance Developer, SlimLogic Ltd ASoC and Voltage Regulator Maintainer. http://www.slimlogic.co.uk
Mark Brown
AppliedQuoted 3 lines · Liam Girdwood
All
Acked-by Liam Girdwood <[email protected]>
Applied, thanks.
В сообщении от 31 августа 2010 15:25:59 автор Mark Brown написал:
Quoted 6 lines · Liam Girdwood
Quoted 3 lines
All
Acked-by Liam Girdwood <[email protected]>Applied, thanks.
Mark, maybe merging third patch without Ben's comment is not good idea? It touches arch/arm/plat-s3c24xx/devs.c
Regards
Vasily
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
Quoted 2 lines · Vasily Khoruzhick
Mark, maybe merging third patch without Ben's comment is not good idea? It touches
arch/arm/plat-s3c24xx/devs.c
It's required for multi-component which is going in during the next merge window and Ben is currently not very available. If there's a problem we can always fix it up later.