msm: qsd8x50: Add support for USB peripheral
Subsystems (3)
PATCH 1/1 msm: qsd8x50: Add support for USB peripheral
Signed-off-by Pavankumar Kondeti <[email protected]>
--- arch/arm/mach-msm/board-qsd8x50.c | 59 ++++++++++++++++++++++++++++++++ arch/arm/mach-msm/devices-qsd8x50.c | 23 ++++++++++++ arch/arm/mach-msm/include/mach/board.h | 5 +++ 3 files changed, 87 insertions(+), 0 deletions(-)
arch/arm/mach-msm/board-qsd8x50.c +59 -0
@@ -20,6 +20,9 @@#include <linux/gpio.h> #include <linux/platform_device.h> #include <linux/delay.h> +#include <linux/err.h> +#include <linux/clk.h> +#include <linux/usb/msm_hsusb.h> #include <asm/mach-types.h> #include <asm/mach/arch.h>
@@ -35,6 +38,60 @@extern struct sys_timer msm_timer; +static int hsusb_phy_init_seq[] = { +0x08 ,0x31 ,/* Increase HS Driver Amplitude */ +0x20 ,0x32 ,/* Enable and set Pre-Emphasis Depth to 10% */ +-1 }; + +static void hsusb_phy_reset (void ) +{ +struct clk *phy_reset_clk; +int ret; + + phy_reset_clk =clk_get (NULL ,"usb_phy_clk" ); +if (IS_ERR (phy_reset_clk)) { +pr_err ("%s: failed to get usb_phy_clk\n" , __func__); +return ; + } + + ret =clk_reset (phy_reset_clk,CLK_RESET_ASSERT ); +if (ret) { +pr_err ("%s: phy clk assert failed\n" , __func__); +clk_put (phy_reset_clk); +return ; + } +usleep_range (1000 ,1200 ); + ret =clk_reset (phy_reset_clk,CLK_RESET_DEASSERT ); +if (ret) +pr_err ("%s: phy clk deassert failed\n" , __func__); +clk_put (phy_reset_clk); +} + +static void hsusb_hw_reset (bool enable) +{ +struct clk *hs_clk; +int ret; + + hs_clk =clk_get (NULL ,"usb_hs_clk" ); +if (IS_ERR (hs_clk)) { +pr_err ("%s: failed to get usb_hs_clk\n" , __func__); +return ; + } + ret =clk_reset (hs_clk, enable ?CLK_RESET_ASSERT :CLK_RESET_DEASSERT ); +if (ret) +pr_err ("%s: usb hs_clk %s failed\n" , __func__, + enable ?"assert" :"deassert" ); + +clk_put (hs_clk); +} + + +static struct msm_hsusb_platform_data msm_hsusb_pdata = { + .phy_init_seq = hsusb_phy_init_seq, + .phy_reset = hsusb_phy_reset, + .hw_reset = hsusb_hw_reset, +}; +static struct msm_gpio uart3_config_data[] = { {GPIO_CFG (86 ,1 ,GPIO_INPUT ,GPIO_PULL_DOWN ,GPIO_2MA ),"UART2_Rx" }, {GPIO_CFG (87 ,1 ,GPIO_OUTPUT ,GPIO_PULL_DOWN ,GPIO_2MA ),"UART2_Tx" },
@@ -42,6 +99,7 @@ static struct msm_gpio uart3_config_data[] = {static struct platform_device *devices[]__initdata = { &msm_device_uart3, + &msm_device_hsusb, };static void msm8x50_init_uart3 (void )
@@ -65,6 +123,7 @@ static void __init qsd8x50_init_irq(void)static void __init qsd8x50_init (void ) {msm8x50_init_uart3 (); + msm_device_hsusb.dev.platform_data = &msm_hsusb_pdata;platform_add_devices (devices,ARRAY_SIZE (devices)); }
arch/arm/mach-msm/devices-qsd8x50.c +23 -0
@@ -28,6 +28,29 @@#include <mach/mmc.h> +static struct resource resources_hsusb[] = { + { + .start =MSM_HSUSB_PHYS , + .end =MSM_HSUSB_PHYS +MSM_HSUSB_SIZE , + .flags =IORESOURCE_MEM , + }, + { + .start =INT_USB_HS , + .end =INT_USB_HS , + .flags =IORESOURCE_IRQ , + }, +}; + +struct platform_device msm_device_hsusb = { + .name ="msm_hsusb" , + .id =-1 , + .num_resources =ARRAY_SIZE (resources_hsusb), + .resource = resources_hsusb, + .dev = { + .coherent_dma_mask =0xffffffff , + }, +}; +static struct resource resources_uart3[] = { { .start =INT_UART3 ,
arch/arm/mach-msm/include/mach/board.h +5 -0
@@ -44,5 +44,10 @@ void __init msm_acpu_clock_init(struct msm_acpu_clock_platform_data *);int __init msm_add_sdcc (unsigned int controller,struct msm_mmc_platform_data *plat,unsigned int stat_irq,unsigned long stat_irq_flags); +#ifdef CONFIG_USB_MSM_72K +void msm_hsusb_set_vbus_state (int online); +#else +static inline void msm_hsusb_set_vbus_state (int online) {} +#endif #endif
Signature · 5 lines
1.7.1 -- Sent by a consultant of the Qualcomm Innovation Center, Inc. The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.