Skip to contentSkip to conversation

Add support for Seagate FreeAgent DockStar

PATCH Superseded Eric Cooper 6 participants 30 messages Sep 7, 2010 – Oct 21, 2010 1 message not in the archive

Subsystems (2)

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

cover Add support for Seagate FreeAgent DockStar

This patch series adds support for the Seagate FreeAgent DockStar. The DockStar is almost identical to the Marvell SheevaPlug, but has 256M of NAND flash, 128M of SDRAM, and different LED pins.

A new machine ID (2998) has already been registered for this device.

Alexander Holler (2):
DockStar: change RAM definitions to one bank (128 MB)
DockStar: config

Eric Cooper (3):
add DOCKSTAR machine type
DockStar: board support (derived from sheevaplug)
DockStar: LED support

 arch/arm/include/asm/mach-types.h   |   13 ++
 board/Marvell/dockstar/Makefile     |   51 ++++++++
 board/Marvell/dockstar/config.mk    |   28 +++++
 board/Marvell/dockstar/dockstar.c   |  185 +++++++++++++++++++++++++++++
 board/Marvell/dockstar/dockstar.h   |   41 +++++++
 board/Marvell/dockstar/kwbimage.cfg |  162 ++++++++++++++++++++++++++
 boards.cfg                          |    1 +
 include/configs/dockstar.h          |  217 +++++++++++++++++++++++++++++++++++
 8 files changed, 698 insertions(+), 0 deletions(-)
 create mode 100644 board/Marvell/dockstar/Makefile
 create mode 100644 board/Marvell/dockstar/config.mk
 create mode 100644 board/Marvell/dockstar/dockstar.c
 create mode 100644 board/Marvell/dockstar/dockstar.h
 create mode 100644 board/Marvell/dockstar/kwbimage.cfg
 create mode 100644 include/configs/dockstar.h
#1 lore raw

PATCH 1/5 add DOCKSTAR machine type

---
 arch/arm/include/asm/mach-types.h |   13 +++++++++++++
 1 files changed, 13 insertions(+), 0 deletions(-)
arch/arm/include/asm/mach-types.h +13 -0
index fd28d2b..e0b6090 100644
@@ -2946,6 +2946,7 @@ extern unsigned int __machine_arch_type;
 #define MACH_TYPE_NETVIZ               2964
 #define MACH_TYPE_FLEXIBITY            2965
 #define MACH_TYPE_WLAN_COMPUTER        2966
+#define MACH_TYPE_DOCKSTAR             2998
 
 #ifdef CONFIG_ARCH_EBSA110
 # ifdef machine_arch_type
@@ -38155,6 +38156,18 @@ extern unsigned int __machine_arch_type;
 # define machine_is_wlan_computer()	(0)
 #endif
 
+#ifdef CONFIG_MACH_DOCKSTAR
+# ifdef machine_arch_type
+#  undef machine_arch_type
+#  define machine_arch_type	__machine_arch_type
+# else
+#  define machine_arch_type	MACH_TYPE_DOCKSTAR
+# endif
+# define machine_is_dockstar()	(machine_arch_type == MACH_TYPE_DOCKSTAR)
+#else
+# define machine_is_dockstar()	(0)
+#endif
+
 /*
  * These have not yet been registered
  */
Signature · 1 line
1.7.1
#2 lore raw

PATCH 1/5 add DOCKSTAR machine type

Dear Eric Cooper,

Quoted 11 lines · In message <[email protected]> you wrote:
---
 arch/arm/include/asm/mach-types.h |   13 +++++++++++++
 1 files changed, 13 insertions(+), 0 deletions(-)
arch/arm/include/asm/mach-types.h +0 -0
index fd28d2b..e0b6090 100644

arch/arm/include/asm/mach-types.h extern unsigned int __machine_arch_type; · line 2950

Quoted 5 lines
arch/arm/include/asm/mach-types.h +1 -0
@@ -2946,6 +2946,7 @@ extern unsigned int __machine_arch_type;
 #define MACH_TYPE_NETVIZ               2964
 #define MACH_TYPE_FLEXIBITY            2965
 #define MACH_TYPE_WLAN_COMPUTER        2966
+#define MACH_TYPE_DOCKSTAR             2998
 

NAK. We don't edit mach-types.h manually.

If you need it updated, please send a request to do so to the acting ARM custodian (ahem).

But also note that we always sync against the current mainline Linux kernel, and this does not have an entry for DOCKSTAR yet (it ends at WLAN_COMPUTER), so a new sync would not change the file yet.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
I can't understand it. I can't even understand  the  people  who  can
understand it.                    - Queen Juliana of the Netherlands.
#3 lore raw

PATCH 2/5 DockStar: board support (derived from sheevaplug)

In reply to Eric Cooper
---
 board/Marvell/dockstar/Makefile   |   51 ++++++++++++
 board/Marvell/dockstar/config.mk  |   28 +++++++
 board/Marvell/dockstar/dockstar.c |  155 +++++++++++++++++++++++++++++++++++++
 board/Marvell/dockstar/dockstar.h |   41 ++++++++++
 boards.cfg                        |    1 +
 5 files changed, 276 insertions(+), 0 deletions(-)
 create mode 100644 board/Marvell/dockstar/Makefile
 create mode 100644 board/Marvell/dockstar/config.mk
 create mode 100644 board/Marvell/dockstar/dockstar.c
 create mode 100644 board/Marvell/dockstar/dockstar.h
board/Marvell/dockstar/Makefile new file +51 -0
new file mode 100644
index 0000000..da9d29e
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <[email protected]>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	:= dockstar.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
board/Marvell/dockstar/config.mk new file +28 -0
new file mode 100644
index 0000000..2bd9f79
@@ -0,0 +1,28 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <[email protected]>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+TEXT_BASE = 0x00600000
+
+# Kirkwood Boot Image configuration file
+KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg
board/Marvell/dockstar/dockstar.c new file +155 -0

155 lines not on this page · raw message

board/Marvell/dockstar/dockstar.h new file +41 -0

41 lines not on this page · raw message

boards.cfg +1 -0
index 69c6897..f97927b 100644
@@ -250,6 +250,7 @@ guruplug	arm	arm926ejs	-		Marvell		kirkwood
 mv88f6281gtw_ge	arm	arm926ejs	-		Marvell		kirkwood
 openrd_base	arm	arm926ejs	-		Marvell		kirkwood
 sheevaplug	arm	arm926ejs	-		Marvell		kirkwood
+dockstar	arm	arm926ejs	-		Marvell		kirkwood
 imx27lite	arm	arm926ejs	imx27lite	logicpd		mx27
 magnesium	arm	arm926ejs	imx27lite	logicpd		mx27
 omap5912osk	arm	arm926ejs	-		ti		omap
Signature · 1 line
1.7.1
#4 lore raw

PATCH 2/5 DockStar: board support (derived from sheevaplug)

Dear Eric Cooper,

Quoted 13 lines · In message <[email protected]> you wrote:
---
 board/Marvell/dockstar/Makefile   |   51 ++++++++++++
 board/Marvell/dockstar/config.mk  |   28 +++++++
 board/Marvell/dockstar/dockstar.c |  155 +++++++++++++++++++++++++++++++++++++
 board/Marvell/dockstar/dockstar.h |   41 ++++++++++
 boards.cfg                        |    1 +
 5 files changed, 276 insertions(+), 0 deletions(-)
 create mode 100644 board/Marvell/dockstar/Makefile
 create mode 100644 board/Marvell/dockstar/config.mk
 create mode 100644 board/Marvell/dockstar/dockstar.c
 create mode 100644 board/Marvell/dockstar/dockstar.h

Entries to MAINTAINERS and MAKEALL missing.

Board config file missing. Did you try to compile this code?

Also, please rebase your code on top of Heiko's ARM rework patches (enable caches, add relocation). These will go in before your board support.

Best regards,

Wolfgang Denk

Signature · 6 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Nothing in progression can rest on its original plan. We may as  well
think  of  rocking  a grown man in the cradle of an infant.
- Edmund Burke

A message that is not in the archive (sent off-list or not yet received): 20100908010601.GG8903@localhost

#6 lore raw

PATCH 2/5 DockStar: board support (derived from sheevaplug)

Dear Eric Cooper,

please keep the mailing list on Cc:

Quoted 6 lines · In message <20100908010601.GG8903@localhost> you wrote:
Quoted 3 lines

Also, please rebase your code on top of Heiko's ARM rework patches (enable caches, add relocation). These will go in before your board support.

Thanks for your comments and your patience with my first-time submission. Is Heiko's ARM work available on one of the git repos?

Sure. Please see the "arm-reloc-and-cache-support" branch in the u-boot-testing repository: git://git.denx.de/u-boot-testing.git

http://git.denx.de/?p=u-boot/u-boot-testing.git;a=shortlog;h=refs/heads/arm-reloc-and-cache-support

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Humans do claim a great deal for that particular emotion (love).
	-- Spock, "The Lights of Zetar", stardate 5725.6
#7 lore raw

PATCH 3/5 DockStar: change RAM definitions to one bank (128 MB)

In reply to Eric Cooper

From: Alexander Holler <[email protected]>

---
 board/Marvell/dockstar/kwbimage.cfg |  162 +++++++++++++++++++++++++++++++++++
 1 files changed, 162 insertions(+), 0 deletions(-)
 create mode 100644 board/Marvell/dockstar/kwbimage.cfg
board/Marvell/dockstar/kwbimage.cfg new file +162 -0
new file mode 100644
index 0000000..46d504c
@@ -0,0 +1,162 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <[email protected]>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM	nand
+NAND_ECC_MODE	default
+NAND_PAGE_SIZE	0x0800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1b1b1b9b
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xFFD01400 0x43000c30	# DDR Configuration register
+# bit13-0:  0xc30 (3120 DDR2 clks refresh rate)
+# bit23-14: zero
+# bit24: 1= enable exit self refresh mode on DDR access
+# bit25: 1 required
+# bit29-26: zero
+# bit31-30: 01
+
+DATA 0xFFD01404 0x37543000	# DDR Controller Control Low
+# bit 4:    0=addr/cmd in smame cycle
+# bit 5:    0=clk is driven during self refresh, we don't care for APX
+# bit 6:    0=use recommended falling edge of clk for addr/cmd
+# bit14:    0=input buffer always powered up
+# bit18:    1=cpu lock transaction enabled
+# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 3 required
+# bit31:    0=no additional STARTBURST delay
+
+DATA 0xFFD01408 0x22125451	# DDR Timing (Low) (active cycles value +1)
+# bit3-0:   TRAS lsbs
+# bit7-4:   TRCD
+# bit11- 8: TRP
+# bit15-12: TWR
+# bit19-16: TWTR
+# bit20:    TRAS msb
+# bit23-21: 0x0
+# bit27-24: TRRD
+# bit31-28: TRTP
+
+DATA 0xFFD0140C 0x00000a33	#  DDR Timing (High)
+# bit6-0:   TRFC
+# bit8-7:   TR2R
+# bit10-9:  TR2W
+# bit12-11: TW2W
+# bit31-13: zero required
+
+DATA 0xFFD01410 0x0000000d	#  DDR Address Control
+# bit1-0:   00, Cs0width=x8
+# bit3-2:   11, Cs0size=1Gb
+# bit5-4:   00, Cs1width=nonexistent
+# bit7-6:   00, Cs1size =nonexistent
+# bit9-8:   00, Cs2width=nonexistent
+# bit11-10: 00, Cs2size =nonexistent
+# bit13-12: 00, Cs3width=nonexistent
+# bit15-14: 00, Cs3size =nonexistent
+# bit16:    0,  Cs0AddrSel
+# bit17:    0,  Cs1AddrSel
+# bit18:    0,  Cs2AddrSel
+# bit19:    0,  Cs3AddrSel
+# bit31-20: 0 required
+
+DATA 0xFFD01414 0x00000000	#  DDR Open Pages Control
+# bit0:    0,  OpenPage enabled
+# bit31-1: 0 required
+
+DATA 0xFFD01418 0x00000000	#  DDR Operation
+# bit3-0:   0x0, DDR cmd
+# bit31-4:  0 required
+
+DATA 0xFFD0141C 0x00000C52	#  DDR Mode
+# bit2-0:   2, BurstLen=2 required
+# bit3:     0, BurstType=0 required
+# bit6-4:   4, CL=5
+# bit7:     0, TestMode=0 normal
+# bit8:     0, DLL reset=0 normal
+# bit11-9:  6, auto-precharge write recovery ????????????
+# bit12:    0, PD must be zero
+# bit31-13: 0 required
+
+DATA 0xFFD01420 0x00000040	#  DDR Extended Mode
+# bit0:    0,  DDR DLL enabled
+# bit1:    0,  DDR drive strenght normal
+# bit2:    0,  DDR ODT control lsd (disabled)
+# bit5-3:  000, required
+# bit6:    1,  DDR ODT control msb, (disabled)
+# bit9-7:  000, required
+# bit10:   0,  differential DQS enabled
+# bit11:   0, required
+# bit12:   0, DDR output buffer enabled
+# bit31-13: 0 required
+
+DATA 0xFFD01424 0x0000F17F	#  DDR Controller Control High
+# bit2-0:  111, required
+# bit3  :  1  , MBUS Burst Chop disabled
+# bit6-4:  111, required
+# bit7  :  0
+# bit8  :  1  , add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9  :  0  , no half clock cycle addition to dataout
+# bit10 :  0  , 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11 :  0  , 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 1111 required
+# bit31-16: 0    required
+
+DATA 0xFFD01428 0x00085520	# DDR2 ODT Read Timing (default values)
+DATA 0xFFD0147C 0x00008552	# DDR2 ODT Write Timing (default values)
+
+DATA 0xFFD01500 0x00000000	# CS[0]n Base address to 0x0
+DATA 0xFFD01504 0x07FFFFF1	# CS[0]n Size
+# bit0:    1,  Window enabled
+# bit1:    0,  Write Protect disabled
+# bit3-2:  00, CS0 hit selected
+# bit23-4: ones, required
+# bit31-24: 0x0F, Size (i.e. 256MB)
+
+DATA 0xFFD01508 0x10000000	# CS[1]n Base address to 256Mb
+DATA 0xFFD0150C 0x00000000	# CS[1]n Size, window disabled
+
+DATA 0xFFD01514 0x00000000	# CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000	# CS[3]n Size, window disabled
+
+DATA 0xFFD01494 0x00030000	#  DDR ODT Control (Low)
+DATA 0xFFD01498 0x00000000	#  DDR ODT Control (High)
+# bit1-0:  00, ODT0 controlled by ODT Control (low) register above
+# bit3-2:  01, ODT1 active NEVER!
+# bit31-4: zero, required
+
+DATA 0xFFD0149C 0x0000E803	# CPU ODT Control
+DATA 0xFFD01480 0x00000001	# DDR Initialization Control
+#bit0=1, enable DDR init upon this register write
+
+# End of Header extension
+DATA 0x0 0x0
Signature · 1 line
1.7.1
#8 lore raw

PATCH 3/5 DockStar: change RAM definitions to one bank (128 MB)

Dear Eric Cooper,

Quoted 8 lines · In message <[email protected]> you wrote:

From: Alexander Holler <[email protected]>

---
 board/Marvell/dockstar/kwbimage.cfg |  162 +++++++++++++++++++++++++++++++++++
 1 files changed, 162 insertions(+), 0 deletions(-)
 create mode 100644 board/Marvell/dockstar/kwbimage.cfg

NAK. Please merge this into previous patch.

Best regards,

Wolfgang Denk

Signature · 6 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
One essential to success is that you desire be an all-obsessing  one,
your thoughts and aims be co-ordinated, and your energy be concentra-
ted and applied without letup.
#9 lore raw

PATCH 4/5 DockStar: config

In reply to Eric Cooper

From: Alexander Holler <[email protected]>

Change ident string.
Include long help messages.
Environment is at 0xa0000.
Define MTD partitions and default environment variables.

---
 include/configs/dockstar.h |  218 ++++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 218 insertions(+), 0 deletions(-)
 create mode 100644 include/configs/dockstar.h
include/configs/dockstar.h new file +218 -0
new file mode 100644
index 0000000..a1a97a3
@@ -0,0 +1,218 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_DOCKSTAR_H
+#define _CONFIG_DOCKSTAR_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING	"\nSeagate FreeAgent DockStar"
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_MARVELL		1
+#define CONFIG_ARM926EJS	1	/* Basic Architecture */
+#define CONFIG_FEROCEON_88FR131	1	/* CPU Core subversion */
+#define CONFIG_KIRKWOOD		1	/* SOC Family Name */
+#define CONFIG_KW88F6281	1	/* SOC Name */
+#define CONFIG_MACH_DOCKSTAR	/* Machine type */
+
+#define CONFIG_MD5	/* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
+#define CONFIG_KIRKWOOD_EGIGA_INIT	/* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8	/* Set RGMII Pad voltage to 1.8V */
+
+/*
+ * CLKs configurations
+ */
+#define CONFIG_SYS_HZ		1000
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
+#define CONFIG_SYS_NS16550_CLK		CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1		KW_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX	1	/*Console on UART0 */
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, \
+					  115200,230400, 460800, 921600 }
+/* auto boot */
+#define CONFIG_BOOTDELAY	3	/* default enable autoboot */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG	1	/* enable passing of ATAGs  */
+#define CONFIG_INITRD_TAG	1	/* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1	/* enable memory tag */
+
+#define	CONFIG_SYS_PROMPT	"Marvell>> "	/* Command Prompt */
+#define	CONFIG_SYS_CBSIZE	1024	/* Console I/O Buff Size */
+#define	CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE \
+		+sizeof(CONFIG_SYS_PROMPT) + 16)	/* Print Buff */
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH		/* Declare no flash (NOR/SPI) */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+#define CONFIG_SYS_LONGHELP
+
+/*
+ * NAND configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_KIRKWOOD
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define NAND_MAX_CHIPS			1
+#define CONFIG_SYS_NAND_BASE		0xD8000000	/* KW_DEFADR_NANDF */
+#define NAND_ALLOW_ERASE_ALL		1
+#endif
+
+/*
+ *  Environment variables configurations
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_NAND		1
+#define CONFIG_ENV_SECT_SIZE		0x20000	/* 128K */
+#else
+#define CONFIG_ENV_IS_NOWHERE		1	/* if env in SDRAM */
+#endif
+/*
+ * max 4k env size is enough, but in case of nand
+ * it has to be rounded to sector size
+ */
+#define CONFIG_ENV_SIZE			0x20000	/* 128k */
+#define CONFIG_ENV_ADDR			0xA0000
+#define CONFIG_ENV_OFFSET		0xA0000	/* env starts here */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_MTDPARTS		"mtdparts=orion_nand:1m(uboot),-(root)\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"console=console=ttyS0,115200\0" \
+	"mtdids=nand0=orion_nand\0" \
+	"mtdparts="CONFIG_MTDPARTS \
+	"kernel=/boot/uImage\0" \
+	"initrd=/boot/uInitrd\0" \
+	"bootargs_root=ubi.mtd=1 root=ubi0:root rootfstype=ubifs ro\0"
+
+#define CONFIG_BOOTCOMMAND \
+	"setenv bootargs ${console} ${mtdparts} ${bootargs_root}; "	\
+	"ubi part root; " \
+	"ubifsmount root; " \
+	"ubifsload 0x800000 ${kernel}; " \
+	"ubifsload 0x1100000 ${initrd}; " \
+	"bootm 0x800000 0x1100000"
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN	(1024 * 1024) /* 1 MiB for malloc() */
+/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE	128
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_ARCH_CPU_INIT	/* call arch_cpu_init() */
+#define CONFIG_ARCH_MISC_INIT	/* call arch_misc_init() */
+#define CONFIG_DISPLAY_CPUINFO	/* Display cpu info */
+#define CONFIG_NR_DRAM_BANKS	4
+#define CONFIG_STACKSIZE	0x00100000	/* regular stack- 1M */
+#define CONFIG_SYS_LOAD_ADDR	0x00800000	/* default load adr- 8M */
+#define CONFIG_SYS_MEMTEST_START 0x00400000	/* 4M */
+#define CONFIG_SYS_MEMTEST_END	0x007fffff	/*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000	/* Rst Vector Adr */
+#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NETCONSOLE	/* include NetConsole support   */
+#define CONFIG_NET_MULTI	/* specify more that one ports available */
+#define	CONFIG_MII		/* expose smi ove miiphy interface */
+#define CONFIG_MVGBE		/* Enable Marvell Gbe Controller Driver */
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	/* detect link using phy */
+#define CONFIG_MVGBE_PORTS	{1, 0}	/* enable port 0 only */
+#define CONFIG_PHY_BASE_ADR	0
+#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
+#define CONFIG_RESET_PHY_R	/* use reset_phy() to init mv8831116 PHY */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * USB/EHCI
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI			/* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_KIRKWOOD	/* on Kirkwood platform	*/
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#endif /* CONFIG_CMD_USB */
+
+/*
+ * File system
+ */
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_LZO
+
+#endif /* _CONFIG_DOCKSTAR_H */
Signature · 1 line
1.7.1
#10 lore raw

PATCH 4/5 DockStar: config

Dear Eric Cooper,

Quoted 9 lines · In message <[email protected]> you wrote:

From: Alexander Holler <[email protected]>

Change ident string.
Include long help messages.
Environment is at 0xa0000.
Define MTD partitions and default environment variables.

---

Please squash into patch that adds support for this board.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Power is danger.
	-- The Centurion, "Balance of Terror", stardate 1709.2
#11 lore raw

PATCH 5/5 DockStar: LED support

In reply to Eric Cooper

derived from patches posted by Jeff Doozan
in the uBoot forum at http://forum.doozan.com

---
 board/Marvell/dockstar/dockstar.c |   30 ++++++++++++++++++++++++++++++
 include/configs/dockstar.h        |    1 -
 2 files changed, 30 insertions(+), 1 deletions(-)
board/Marvell/dockstar/dockstar.c +30 -0
index 13cd347..7788837 100644
@@ -153,3 +153,33 @@ void reset_phy(void)
 	printf("88E1116 Initialized on %s\n", name);
 }
 #endif /* CONFIG_RESET_PHY_R */
+
+#define GREEN_LED	(1 << 14)
+#define ORANGE_LED	(1 << 15)
+#define BOTH_LEDS	(GREEN_LED | ORANGE_LED)
+#define NEITHER_LED	0
+
+static void set_leds(u32 leds, u32 blinking)
+{
+	struct kwgpio_registers *r = (struct kwgpio_registers *)KW_GPIO1_BASE;
+	u32 oe = readl(&r->oe) | BOTH_LEDS;
+	writel(oe & ~leds, &r->oe);	/* active low */
+	u32 bl = readl(&r->blink_en) & ~BOTH_LEDS;
+	writel(bl | blinking, &r->blink_en);
+}
+
+void show_boot_progress(int val)
+{
+	switch (val) {
+	    case 15:	/* booting Linux */
+		set_leds(BOTH_LEDS, NEITHER_LED);
+		break;
+	    case 64:	/* Ethernet initialization */
+		set_leds(GREEN_LED, GREEN_LED);
+		break;
+	    default:
+		if (val < 0)	/* error */
+			set_leds(ORANGE_LED, ORANGE_LED);
+		break;
+	}
+}
include/configs/dockstar.h +0 -1
index a1a97a3..ecd5f27 100644
@@ -181,7 +181,6 @@
 #define CONFIG_NET_MULTI	/* specify more that one ports available */
 #define	CONFIG_MII		/* expose smi ove miiphy interface */
 #define CONFIG_MVGBE		/* Enable Marvell Gbe Controller Driver */
-#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	/* detect link using phy */
 #define CONFIG_MVGBE_PORTS	{1, 0}	/* enable port 0 only */
 #define CONFIG_PHY_BASE_ADR	0
 #define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
Signature · 1 line
1.7.1
#12 lore raw

PATCH 5/5 DockStar: LED support

Dear Eric Cooper,

Quoted 2 lines · In message <[email protected]> you wrote:

derived from patches posted by Jeff Doozan
in the uBoot forum at http://forum.doozan.com

Please squash into patch that adds support for this board.

include/configs/dockstar.h line 184

Quoted 9 lines
include/configs/dockstar.h +0 -1
index a1a97a3..ecd5f27 100644
@@ -181,7 +181,6 @@
 #define CONFIG_NET_MULTI	/* specify more that one ports available */
 #define	CONFIG_MII		/* expose smi ove miiphy interface */
 #define CONFIG_MVGBE		/* Enable Marvell Gbe Controller Driver */
-#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	/* detect link using phy */

This is a modification which is completely unrelated to that patch anyway.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
An expert is a person who avoids the small errors while  sweeping  on
to the grand fallacy.
#13 lore raw

PATCH 5/5 DockStar: LED support

In reply to Eric Cooper

Hello.

Quoted 4 lines · Eric Cooper

derived from patches posted by Jeff Doozan
in the uBoot forum at http://forum.doozan.com

[...]

Quoted 17 lines
board/Marvell/dockstar/dockstar.c +9 -0
index 13cd347..7788837 100644
@@ -153,3 +153,33 @@ void reset_phy(void)
  	printf("88E1116 Initialized on %s\n", name);
  }
  #endif /* CONFIG_RESET_PHY_R */
+
+#define GREEN_LED	(1<<  14)
+#define ORANGE_LED	(1<<  15)
+#define BOTH_LEDS	(GREEN_LED | ORANGE_LED)
+#define NEITHER_LED	0
+
+static void set_leds(u32 leds, u32 blinking)
+{
+	struct kwgpio_registers *r = (struct kwgpio_registers *)KW_GPIO1_BASE;

board/Marvell/dockstar/dockstar.c void reset_phy(void) · line 174

Quoted 10 lines
board/Marvell/dockstar/dockstar.c +10 -0
+	u32 oe = readl(&r->oe) | BOTH_LEDS;
+	writel(oe&  ~leds,&r->oe);	/* active low */
+	u32 bl = readl(&r->blink_en)&  ~BOTH_LEDS;
+	writel(bl | blinking,&r->blink_en);
+}
+
+void show_boot_progress(int val)
+{
+	switch (val) {
+	    case 15:	/* booting Linux */

*case* should be aligned with *switch*. Don't align using spaces.

board/Marvell/dockstar/dockstar.c void reset_phy(void) · line 185

Quoted 11 lines
board/Marvell/dockstar/dockstar.c +11 -0
+		set_leds(BOTH_LEDS, NEITHER_LED);
+		break;
+	    case 64:	/* Ethernet initialization */
+		set_leds(GREEN_LED, GREEN_LED);
+		break;
+	    default:
+		if (val < 0)	/* error */
+			set_leds(ORANGE_LED, ORANGE_LED);
+		break;
+	}
+}

WBR, Sergei

#14 lore raw

cover Add support for Seagate FreeAgent DockStar

In reply to Eric Cooper

Am 07.09.2010 16:28, schrieb Eric Cooper:

Quoted 31 lines

This patch series adds support for the Seagate FreeAgent DockStar. The DockStar is almost identical to the Marvell SheevaPlug, but has 256M of NAND flash, 128M of SDRAM, and different LED pins.

A new machine ID (2998) has already been registered for this device.

Alexander Holler (2):
DockStar: change RAM definitions to one bank (128 MB)
DockStar: config

Eric Cooper (3):
add DOCKSTAR machine type
DockStar: board support (derived from sheevaplug)
DockStar: LED support

 arch/arm/include/asm/mach-types.h   |   13 ++
 board/Marvell/dockstar/Makefile     |   51 ++++++++
 board/Marvell/dockstar/config.mk    |   28 +++++
 board/Marvell/dockstar/dockstar.c   |  185 +++++++++++++++++++++++++++++
 board/Marvell/dockstar/dockstar.h   |   41 +++++++
 board/Marvell/dockstar/kwbimage.cfg |  162 ++++++++++++++++++++++++++
 boards.cfg                          |    1 +
 include/configs/dockstar.h          |  217 +++++++++++++++++++++++++++++++++++
 8 files changed, 698 insertions(+), 0 deletions(-)
 create mode 100644 board/Marvell/dockstar/Makefile
 create mode 100644 board/Marvell/dockstar/config.mk
 create mode 100644 board/Marvell/dockstar/dockstar.c
 create mode 100644 board/Marvell/dockstar/dockstar.h
 create mode 100644 board/Marvell/dockstar/kwbimage.cfg
 create mode 100644 include/configs/dockstar.h
Quoted 4 lines

_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Hello Eric,

can you rework your patch set and send v2? Or do you need help?

Thomas

#15 lore raw

[U-Boot] How to debug u-boot with GDB & BDI3000

Thanks for your time.

I 'm just working on a u-boot on the board with CN5010, but it looks like
there are some problems with GDB and BDI3000. I have built the debug
environment covering GDB & BDI3000 & my board, but later I sadly found that the breakpoint doesn't work.

Could you give me some suggestions?

Thanks!
Shuyou

#16 lore raw

[U-Boot] How to debug u-boot with GDB & BDI3000

Dear "sywang",

Quoted 5 lines · In message <[email protected]> you wrote:

I 'm just working on a u-boot on the board with CN5010, but it looks like
there are some problems with GDB and BDI3000. I have built the debug
environment covering GDB & BDI3000 & my board, but later I sadly found that the breakpoint doesn't work.

We don't know your hardware, and we don't know your code.

We cannot support you with stuff that is kept closed. And we explained this before.

Please contact Cavium technical support.

Best regards,

Wolfgang Denk

Signature · 6 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
At the source of every error which is blamed on the computer you will
find at least two human errors, including the error of blaming it  on
the computer.
#17 lore raw

[U-Boot] How to debug u-boot with GDB & BDI3000

Thanks for your comments.

Who has done this? Please contact me.

Thanks!
Shuyou

-----Original Message-----
From: Wolfgang Denk [mailto:wd at denx.de]
Sent: 2010?9?27? 18:08
To: sywang
Cc: u-boot at lists.denx.de
Subject: Re: [U-Boot] How to debug u-boot with GDB & BDI3000

Dear "sywang",

Quoted 4 lines · In message <[email protected]> you wrote:

I 'm just working on a u-boot on the board with CN5010, but it looks like
there are some problems with GDB and BDI3000. I have built the debug
environment covering GDB & BDI3000 & my board, but later I sadly found

that

Quoted 1 line

the breakpoint doesn't work.

We don't know your hardware, and we don't know your code.

We cannot support you with stuff that is kept closed. And we explained this before.

Please contact Cavium technical support.

Best regards,

Wolfgang Denk

Signature · 6 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
At the source of every error which is blamed on the computer you will
find at least two human errors, including the error of blaming it  on
the computer.
#18 lore raw

cover Add support for Seagate FreeAgent DockStar

In reply to Thomas Weber
Quoted 1 line · Thomas Weber

can you rework your patch set and send v2? Or do you need help?

I was going to wait until the sheevaplug or guruplug boards had been modified for the ARM relocation changes and then base my v2 on that. I don't really know enough about the hardware to do it myself, and since I don't have a JTAG environment ready in case I mess it up, I don't really want to "experiment" :-)

Signature · 1 line
Eric Cooper             e c c @ c m u . e d u
#19 lore raw

PATCH v2 1/1 Seagate FreeAgent DockStar support

In reply to Thomas Weber

start with sheevaplug configuration
add modifications by Alexander Holler <[email protected]>
change RAM definitions to one bank (128 MB) change ident string
change environment to 0xA0000
define MTD partitions and default environment variables add support for LEDs

---
Changes for v2:
- rebased on master, post ARM and kirkwood relocation changes
- squashed into single commit
Pending patches that this depends on:
Gray Remlin:
kirkwood: Fix uninitialised DRAM struct
Prafulla Wadaskar:
Kirkwood: bugfix: broken early console messages

 MAINTAINERS                         |    4 +
 MAKEALL                             |    1 +
 board/Marvell/dockstar/Makefile     |   51 ++++++++++
 board/Marvell/dockstar/config.mk    |   28 ++++++
 board/Marvell/dockstar/dockstar.c   |  178 +++++++++++++++++++++++++++++++++++
 board/Marvell/dockstar/dockstar.h   |   41 ++++++++
 board/Marvell/dockstar/kwbimage.cfg |  162 +++++++++++++++++++++++++++++++
 boards.cfg                          |    1 +
 include/configs/dockstar.h          |  119 +++++++++++++++++++++++
 9 files changed, 585 insertions(+), 0 deletions(-)
 create mode 100644 board/Marvell/dockstar/Makefile
 create mode 100644 board/Marvell/dockstar/config.mk
 create mode 100644 board/Marvell/dockstar/dockstar.c
 create mode 100644 board/Marvell/dockstar/dockstar.h
 create mode 100644 board/Marvell/dockstar/kwbimage.cfg
 create mode 100644 include/configs/dockstar.h
MAINTAINERS +4 -0
index 5108c54..0a25971 100644
@@ -585,6 +585,10 @@ Po-Yu Chuang <[email protected]>
 
 	a320evb		FA526 (ARM920T-like) (a320 SoC)
 
+Eric Cooper <[email protected]>
+
+	dockstar	ARM926EJS (Kirkwood SoC)
+
 George G. Davis <[email protected]>
 
 	assabet		SA1100
MAKEALL +1 -0
index c1f3842..83679b4 100755
@@ -327,6 +327,7 @@ LIST_ARM9="			\
 	cp966			\
 	da830evm		\
 	da850evm		\
+	dockstar		\
 	edb9301			\
 	edb9302			\
 	edb9302a		\
board/Marvell/dockstar/Makefile new file +51 -0

51 lines not on this page · raw message

board/Marvell/dockstar/config.mk new file +28 -0
new file mode 100644
index 0000000..761c2bb
@@ -0,0 +1,28 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <[email protected]>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+CONFIG_SYS_TEXT_BASE = 0x00600000
+
+# Kirkwood Boot Image configuration file
+KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg
board/Marvell/dockstar/dockstar.c new file +178 -0

178 lines not on this page · raw message

board/Marvell/dockstar/dockstar.h new file +41 -0

41 lines not on this page · raw message

board/Marvell/dockstar/kwbimage.cfg new file +162 -0

162 lines not on this page · raw message

boards.cfg +1 -0
index 3a965e9..6542be4 100644
@@ -361,6 +361,7 @@ guruplug	arm	arm926ejs	-		Marvell		kirkwood
 mv88f6281gtw_ge	arm	arm926ejs	-		Marvell		kirkwood
 openrd_base	arm	arm926ejs	-		Marvell		kirkwood
 sheevaplug	arm	arm926ejs	-		Marvell		kirkwood
+dockstar	arm	arm926ejs	-		Marvell		kirkwood
 imx27lite	arm	arm926ejs	imx27lite	logicpd		mx27
 magnesium	arm	arm926ejs	imx27lite	logicpd		mx27
 omap5912osk	arm	arm926ejs	-		ti		omap
include/configs/dockstar.h new file +119 -0

119 lines not on this page · raw message

Signature · 1 line
1.7.1
#20 lore raw

PATCH v2 1/1 Seagate FreeAgent DockStar support

Quoted 29 lines

-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Eric Cooper
Sent: Wednesday, October 20, 2010 8:25 PM
To: u-boot at lists.denx.de
Cc: Eric Cooper
Subject: [U-Boot] [PATCH v2] Seagate FreeAgent DockStar support

start with sheevaplug configuration
add modifications by Alexander Holler <[email protected]>
change RAM definitions to one bank (128 MB) change ident string
change environment to 0xA0000
define MTD partitions and default environment variables add support for LEDs

---
Changes for v2:
- rebased on master, post ARM and kirkwood relocation changes
- squashed into single commit
Pending patches that this depends on:
Gray Remlin:
kirkwood: Fix uninitialised DRAM struct
Prafulla Wadaskar:
Kirkwood: bugfix: broken early console messages

Quoted 3 lines
 MAINTAINERS                         |    4 +
 MAKEALL                             |    1 +
 board/Marvell/dockstar/Makefile     |   51 ++++++++++

This is not Marvell owned board, so it must go in board/Seagate or board/dockstar folder

Quoted 50 lines
 board/Marvell/dockstar/config.mk    |   28 ++++++
 board/Marvell/dockstar/dockstar.c   |  178 
+++++++++++++++++++++++++++++++++++
 board/Marvell/dockstar/dockstar.h   |   41 ++++++++
 board/Marvell/dockstar/kwbimage.cfg |  162 
+++++++++++++++++++++++++++++++
 boards.cfg                          |    1 +
 include/configs/dockstar.h          |  119 +++++++++++++++++++++++
 9 files changed, 585 insertions(+), 0 deletions(-)
 create mode 100644 board/Marvell/dockstar/Makefile
 create mode 100644 board/Marvell/dockstar/config.mk
 create mode 100644 board/Marvell/dockstar/dockstar.c
 create mode 100644 board/Marvell/dockstar/dockstar.h
 create mode 100644 board/Marvell/dockstar/kwbimage.cfg
 create mode 100644 include/configs/dockstar.h
MAINTAINERS +4 -0
index 5108c54..0a25971 100644
@@ -585,6 +585,10 @@ Po-Yu Chuang <[email protected]>
 
 	a320evb		FA526 (ARM920T-like) (a320 SoC)
 
+Eric Cooper <[email protected]>
+
+	dockstar	ARM926EJS (Kirkwood SoC)
+
 George G. Davis <[email protected]>
 
 	assabet		SA1100
MAKEALL +1 -0
index c1f3842..83679b4 100755
@@ -327,6 +327,7 @@ LIST_ARM9="			\
 	cp966			\
 	da830evm		\
 	da850evm		\
+	dockstar		\
 	edb9301			\
 	edb9302			\
 	edb9302a		\
board/Marvell/dockstar/Makefile new file +0 -0
new file mode 100644
index 0000000..da9d29e

board/Marvell/dockstar/Makefile line 4

Quoted 4 lines
board/Marvell/dockstar/Makefile new file +4 -0
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <[email protected]>

This is to be updated, you can say "based/referenced" Ditto for other files

Regards..
Prafulla . .

#21 lore raw

PATCH v2 1/1 Seagate FreeAgent DockStar support

Quoted 2 lines · Prafulla Wadaskar

This is not Marvell owned board, so it must go in board/Seagate or board/dockstar folder

board/Seagate/dockstar/ would be my preference, since there are similar products like the "Go Flex" that might go in board/Seagate/ someday.

Any problem with this, given that I am not affiliated with Seagate in any way?

Signature · 1 line
Eric Cooper             e c c @ c m u . e d u
#22 lore raw

PATCH v2 1/1 Seagate FreeAgent DockStar support

Dear Eric Cooper,

Quoted 10 lines · In message <20101021150117.GB6772@localhost> you wrote:
Quoted 2 lines · Prafulla Wadaskar

This is not Marvell owned board, so it must go in board/Seagate or board/dockstar folder

board/Seagate/dockstar/ would be my preference, since there are similar products like the "Go Flex" that might go in board/Seagate/ someday.

Any problem with this, given that I am not affiliated with Seagate in any way?

Not at all. It's the board vendor directory, but everybody can submit code for any boards from any vendors.

Best regards,

Wolfgang Denk

Signature · 6 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
HANDLE WITH EXTREME CARE:  This Product Contains  Minute Electrically
Charged  Particles  Moving  at  Velocities  in Excess of Five Hundred
Million Miles Per Hour.
#23 lore raw

PATCH v2 1/1 Seagate FreeAgent DockStar support

In reply to Eric Cooper

Dear Eric Cooper,

In message <[email protected]> you wrote:
...

MAKEALL LIST_ARM9=" \ · line 333

Quoted 12 lines
MAKEALL +1 -0
index c1f3842..83679b4 100755
@@ -327,6 +327,7 @@ LIST_ARM9="			\
 	cp966			\
 	da830evm		\
 	da850evm		\
+	dockstar		\
 	edb9301			\
 	edb9302			\
 	edb9302a		\

This is not needed any more for any boards registered in boards.cfg

Quoted 21 lines
board/Marvell/dockstar/config.mk new file +15 -0
new file mode 100644
index 0000000..761c2bb
@@ -0,0 +1,28 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <[email protected]>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of

board/Marvell/dockstar/config.mk line 25

Quoted 10 lines
board/Marvell/dockstar/config.mk new file +10 -0
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+CONFIG_SYS_TEXT_BASE = 0x00600000

Please move this as #define into the board config file.

board/Marvell/dockstar/config.mk line 28

Quoted 2 lines
board/Marvell/dockstar/config.mk new file +2 -0
+# Kirkwood Boot Image configuration file
+KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg

I would like to get rid of this, too. But this needs discussion with Prafulla.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Just because your doctor has a name for your condition  doesn't  mean
he knows what it is.
#24 lore raw

PATCH v2 1/1 Seagate FreeAgent DockStar support

Quoted 10 lines

-----Original Message-----
From: u-boot-bounces at lists.denx.de [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Wolfgang Denk
Sent: Thursday, October 21, 2010 11:47 AM
To: Eric Cooper
Cc: u-boot at lists.denx.de
Subject: Re: [U-Boot] [PATCH v2] Seagate FreeAgent DockStar support

Quoted 5 lines

board/Marvell/dockstar/config.mk line 28

Quoted 2 lines
board/Marvell/dockstar/config.mk new file +2 -0
+# Kirkwood Boot Image configuration file
+KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg

I would like to get rid of this, too. But this needs discussion with Prafulla.

Hi Wolfgang
We can rename KWD_CONFIG to CONFIG_SYS_KWB_CONFIG and have default assignment as above If for some boards default assignment stands invalid, those can be redefined in board config file.

I will post a patch for this, waiting for your comments/ack.

Regards..
Prafulla . .

#25 lore raw

PATCH v2 1/1 Seagate FreeAgent DockStar support

Dear Prafulla Wadaskar,

Quoted 5 lines · In message <[email protected]>…

We can rename KWD_CONFIG to CONFIG_SYS_KWB_CONFIG and have default assignment as above If for some boards default assignment stands invalid, those can be redefined in board config file.

I will post a patch for this, waiting for your comments/ack.

Thanks, but please wait a second... I have something cooking already.

Best regards,

Wolfgang Denk

Signature · 7 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Alan Turing thought about criteria to settle the question of  whether
machines  can think, a question of which we now know that it is about
as relevant as the question of whether submarines can swim.
                                                   -- Edsger Dijkstra
#26 lore raw

RFC PATCH 1/1 kirkwood: get rid of config.mk files

In reply to Prafulla Wadaskar

After moving the definition of CONFIG_SYS_TEXT_BASE to the respective board config files, all Marvell kirkwood board have just a single and common entry in their config.mk files:

	KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg

Replace the only reference to KWD_CONFIG in the top level Makefile by an equivalent setting, and remove all kirkwood config.mk files.

Cc Prafulla Wadaskar <[email protected]>
Cc Siddarth Gore <[email protected]>
Cc Simon Kagstrom <[email protected]>
Cc Heiko Schocher <[email protected]>
Cc Eric Cooper <[email protected]>

---
Hi,

this is a (basicly untested) proposal how to clean up support for the kirkwood boards. Unfortunately I have no hardware available to test any of this, so I need your help here.

Thanks.

Wolfgang Denk

 Makefile                                |    4 ++-
 board/Marvell/guruplug/config.mk        |   27 -------------------------
 board/Marvell/mv88f6281gtw_ge/config.mk |   28 --------------------------
 board/Marvell/openrd_base/config.mk     |   33 -------------------------------
 board/Marvell/rd6281a/config.mk         |   28 --------------------------
 board/Marvell/sheevaplug/config.mk      |   28 --------------------------
 board/keymile/km_arm/config.mk          |   28 --------------------------
 include/configs/guruplug.h              |    2 +
 include/configs/km_arm.h                |    2 +
 include/configs/mv88f6281gtw_ge.h       |    2 +
 include/configs/openrd_base.h           |    2 +
 include/configs/rd6281a.h               |    2 +
 include/configs/sheevaplug.h            |    2 +
 13 files changed, 15 insertions(+), 173 deletions(-)
 delete mode 100644 board/Marvell/guruplug/config.mk
 delete mode 100644 board/Marvell/mv88f6281gtw_ge/config.mk
 delete mode 100644 board/Marvell/openrd_base/config.mk
 delete mode 100644 board/Marvell/rd6281a/config.mk
 delete mode 100644 board/Marvell/sheevaplug/config.mk
 delete mode 100644 board/keymile/km_arm/config.mk
Makefile +3 -1
index 06c71a2..2ec1172 100644
@@ -357,7 +357,9 @@ $(obj)u-boot.imx:       $(obj)u-boot.bin
 		-e $(CONFIG_SYS_TEXT_BASE) -d $< $@
 
 $(obj)u-boot.kwb:       $(obj)u-boot.bin
-		$(obj)tools/mkimage -n $(KWD_CONFIG) -T kwbimage \
+		$(obj)tools/mkimage \
+		-n $(SRCTREE)/board/$(CONFIG_BOARDDIR)/kwbimage.cfg \
+		-T kwbimage \
 		-a $(CONFIG_SYS_TEXT_BASE) -e $(CONFIG_SYS_TEXT_BASE) -d $< $@
 
 $(obj)u-boot.sha1:	$(obj)u-boot.bin
board/Marvell/guruplug/config.mk deleted +0 -27
deleted file mode 100644
index 12d7737..0000000
@@ -1,27 +0,0 @@
-#
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Siddarth Gore <[email protected]>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
-# MA 02110-1301 USA
-#
-
-CONFIG_SYS_TEXT_BASE = 0x00600000
-
-KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg
board/Marvell/mv88f6281gtw_ge/config.mk deleted +0 -28
deleted file mode 100644
index 761c2bb..0000000
@@ -1,28 +0,0 @@
-#
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <[email protected]>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
-# MA 02110-1301 USA
-#
-
-CONFIG_SYS_TEXT_BASE = 0x00600000
-
-# Kirkwood Boot Image configuration file
-KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg
board/Marvell/openrd_base/config.mk deleted +0 -33
deleted file mode 100644
index 5a49280..0000000
@@ -1,33 +0,0 @@
-#
-# (C) Copyright 2009
-# Net Insight <www.netinsight.net>
-# Written-by: Simon Kagstrom <[email protected]>
-#
-# Based on sheevaplug:
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <[email protected]>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
-# MA 02110-1301 USA
-#
-
-CONFIG_SYS_TEXT_BASE = 0x00600000
-
-# Kirkwood Boot Image configuration file
-KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg
board/Marvell/rd6281a/config.mk deleted +0 -28
deleted file mode 100644
index 761c2bb..0000000
@@ -1,28 +0,0 @@
-#
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <[email protected]>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
-# MA 02110-1301 USA
-#
-
-CONFIG_SYS_TEXT_BASE = 0x00600000
-
-# Kirkwood Boot Image configuration file
-KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg
board/Marvell/sheevaplug/config.mk deleted +0 -28
deleted file mode 100644
index 761c2bb..0000000
@@ -1,28 +0,0 @@
-#
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <[email protected]>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
-# MA 02110-1301 USA
-#
-
-CONFIG_SYS_TEXT_BASE = 0x00600000
-
-# Kirkwood Boot Image configuration file
-KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg
board/keymile/km_arm/config.mk deleted +0 -28
deleted file mode 100644
index df4828c..0000000
@@ -1,28 +0,0 @@
-#
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Prafulla Wadaskar <[email protected]>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
-# MA 02110-1301 USA
-#
-
-CONFIG_SYS_TEXT_BASE = 0x004000000
-
-# Kirkwood Boot Image configuration file
-KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg
include/configs/guruplug.h +2 -0
index 2c2682c..64f6f06 100644
@@ -39,6 +39,8 @@
 #define CONFIG_MACH_GURUPLUG	/* Machine type */
 #define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
 
+#define	CONFIG_SYS_TEXT_BASE	0x00600000
+
 /*
  * Commands configuration
  */
include/configs/km_arm.h +2 -0
index faa0f50..4254341 100644
@@ -40,6 +40,8 @@
 #define CONFIG_KW88F6281		/* SOC Name */
 #define CONFIG_MACH_SUEN3		/* Machine type */
 
+#define CONFIG_SYS_TEXT_BASE	0x004000000
+
 /* include common defines/options for all Keymile boards */
 #include "keymile-common.h"
 #undef CONFIG_CMD_DTT
include/configs/mv88f6281gtw_ge.h +2 -0
index d323829..69bd221 100644
@@ -39,6 +39,8 @@
 #define CONFIG_MACH_MV88F6281GTW_GE	/* Machine type */
 #define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
 
+#define CONFIG_SYS_TEXT_BASE	0x00600000
+
 /*
  * Commands configuration
  */
include/configs/openrd_base.h +2 -0
index cfdd09c..a60c4c9 100644
@@ -44,6 +44,8 @@
 #define CONFIG_MACH_OPENRD_BASE	/* Machine type */
 #define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
 
+#define CONFIG_SYS_TEXT_BASE	0x00600000
+
 /*
  * Commands configuration
  */
include/configs/rd6281a.h +2 -0
index 60f9579..634a2b7 100644
@@ -39,6 +39,8 @@
 #define CONFIG_MACH_RD6281A		/* Machine type */
 #define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
 
+#define CONFIG_SYS_TEXT_BASE	0x00600000
+
 /*
  * Commands configuration
  */
include/configs/sheevaplug.h +2 -0
index 83dd8ff..2629344 100644
@@ -39,6 +39,8 @@
 #define CONFIG_MACH_SHEEVAPLUG	/* Machine type */
 #define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
 
+#define CONFIG_SYS_TEXT_BASE	0x00600000
+
 /*
  * Commands configuration
  */
Signature · 1 line
1.7.2.3
#27 lore raw

RFC PATCH 1/1 kirkwood: get rid of config.mk files

Quoted 68 lines

-----Original Message-----
From: Wolfgang Denk [mailto:wd at denx.de]
Sent: Thursday, October 21, 2010 12:08 PM
To: u-boot at lists.denx.de
Cc: Wolfgang Denk; Prafulla Wadaskar; Siddarth Gore; Simon Kagstrom; Heiko Schocher; Eric Cooper
Subject: [RFC] [PATCH] kirkwood: get rid of config.mk files

After moving the definition of CONFIG_SYS_TEXT_BASE to the respective board config files, all Marvell kirkwood board have just a single and common entry in their config.mk files:

	KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg

Replace the only reference to KWD_CONFIG in the top level Makefile by an equivalent setting, and remove all kirkwood config.mk files.

Cc Prafulla Wadaskar <[email protected]>
Cc Siddarth Gore <[email protected]>
Cc Simon Kagstrom <[email protected]>
Cc Heiko Schocher <[email protected]>
Cc Eric Cooper <[email protected]>

---
Hi,

this is a (basicly untested) proposal how to clean up support for the kirkwood boards. Unfortunately I have no hardware available to test any of this, so I need your help here.

Thanks.

Wolfgang Denk

 Makefile                                |    4 ++-
 board/Marvell/guruplug/config.mk        |   27 
-------------------------
 board/Marvell/mv88f6281gtw_ge/config.mk |   28 
--------------------------
 board/Marvell/openrd_base/config.mk     |   33 
-------------------------------
 board/Marvell/rd6281a/config.mk         |   28 
--------------------------
 board/Marvell/sheevaplug/config.mk      |   28 
--------------------------
 board/keymile/km_arm/config.mk          |   28 
--------------------------
 include/configs/guruplug.h              |    2 +
 include/configs/km_arm.h                |    2 +
 include/configs/mv88f6281gtw_ge.h       |    2 +
 include/configs/openrd_base.h           |    2 +
 include/configs/rd6281a.h               |    2 +
 include/configs/sheevaplug.h            |    2 +
 13 files changed, 15 insertions(+), 173 deletions(-)
 delete mode 100644 board/Marvell/guruplug/config.mk
 delete mode 100644 board/Marvell/mv88f6281gtw_ge/config.mk
 delete mode 100644 board/Marvell/openrd_base/config.mk
 delete mode 100644 board/Marvell/rd6281a/config.mk
 delete mode 100644 board/Marvell/sheevaplug/config.mk
 delete mode 100644 board/keymile/km_arm/config.mk
Makefile +0 -0
index 06c71a2..2ec1172 100644

Makefile $(obj)u-boot.imx: $(obj)u-boot.bin · line 361

Quoted 6 lines
Makefile +2 -1
@@ -357,7 +357,9 @@ $(obj)u-boot.imx:       $(obj)u-boot.bin
 		-e $(CONFIG_SYS_TEXT_BASE) -d $< $@
 
 $(obj)u-boot.kwb:       $(obj)u-boot.bin
-		$(obj)tools/mkimage -n $(KWD_CONFIG) -T kwbimage \
+		$(obj)tools/mkimage \
+		-n $(SRCTREE)/board/$(CONFIG_BOARDDIR)/kwbimage.cfg \

Hi Wolfgang
This will not address other forecasted use cases like-
1. if the new board is added to boards/ (i.e. no BOARDDIR)
2. it will force each board to have it's own kwbimage.cfg even though two boards need same configuration, i.e. code duplication.

In my opinion, we can keep this default setup with CONFIG_SYS_KWD_CONFIG support in addition.

Regards..
Prafulla . .

#28 lore raw

RFC PATCH 1/1 kirkwood: get rid of config.mk files

Dear Prafulla,

Quoted 4 lines · In message <[email protected]>…

Makefile $(obj)u-boot.imx: $(obj)u-boot.bin · line 361

Quoted 4 lines
Makefile +2 -1
-		$(obj)tools/mkimage -n $(KWD_CONFIG) -T kwbimage \
+		$(obj)tools/mkimage \
+		-n $(SRCTREE)/board/$(CONFIG_BOARDDIR)/kwbimage.cfg \

Note: I have to admit that I don't really understand what the command is supposed to do (which is why I asked you for help with the testing).

The "-n" option to mkimage means "set image name to 'name'", so the file name given as argument here would only change the name string inside the image, but not affect the image content at all.

I guess this is not how it's supposed to work?

Quoted 8 lines

This will not address other forecasted use cases like-
1. if the new board is added to boards/ (i.e. no BOARDDIR)

2. it will force each board to have it's own kwbimage.cfg even though two boards need same configuration, i.e. code duplication.

In my opinion, we can keep this default setup with CONFIG_SYS_KWD_CONFIG support in addition.

I'm not sure what exactly you mean here. Do you man to replace

	$(SRCTREE)/board/$(CONFIG_BOARDDIR)/kwbimage.cfg

by something like

	$(SRCTREE)/board/$(CONFIG_SYS_KWD_CONFIG)

? I would agree with that, too.

But I definitely want to avoid to have any such board specific configuration information in the config.mk files. Ideally, I want to get completely rid of all board specific config.mk files.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Fascinating is a word I use for the unexpected.
	-- Spock, "The Squire of Gothos", stardate 2124.5
#29 lore raw

RFC PATCH 1/1 kirkwood: get rid of config.mk files

Quoted 16 lines

-----Original Message-----
From: Wolfgang Denk [mailto:wd at denx.de]
Sent: Thursday, October 21, 2010 1:52 PM
To: Prafulla Wadaskar
Cc: u-boot at lists.denx.de; Siddarth Gore; Simon Kagstrom; Heiko Schocher; Eric Cooper
Subject: Re: [RFC] [PATCH] kirkwood: get rid of config.mk files

Dear Prafulla,

In message <[email protected].

Quoted 1 line · com> you wrote:
Quoted 7 lines
Quoted 3 lines

Makefile $(obj)u-boot.imx: $(obj)u-boot.bin · line 361

Quoted 3 lines
Makefile +2 -1
-		$(obj)tools/mkimage -n $(KWD_CONFIG) -T kwbimage \
+		$(obj)tools/mkimage \
+		-n $(SRCTREE)/board/$(CONFIG_BOARDDIR)/kwbimage.cfg \

Note: I have to admit that I don't really understand what the command is supposed to do (which is why I asked you for help with the testing).

Hi Wolfgang
Shall I take this opporunity to modify test and repost this patch?

Regards..
Prafulla . .

#30 lore raw

RFC PATCH 1/1 kirkwood: get rid of config.mk files

Dear Prafulla Wadaskar,

Quoted 2 lines · In message <[email protected]>…

Shall I take this opporunity to modify test and repost this patch?

Yes, please do! Thanks!

Best regards,

Wolfgang Denk

Signature · 4 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Artificial Intelligence is no match for natural stupidity.