rx1950: add rest of devices
Subsystems (3)
cover rx1950: add rest of devices
This series adds battery device, LEDs device and sound codec device to mach-rx1950.c
PATCH 1/3 rx1950: add battery device
--- arch/arm/mach-s3c2440/Kconfig | 3 + arch/arm/mach-s3c2440/mach-rx1950.c | 160 +++++++++++++++++++++++++++++++++++ 2 files changed, 163 insertions(+), 0 deletions(-)
arch/arm/mach-s3c2440/Kconfig +3 -0
@@ -198,6 +198,9 @@ config MACH_RX1950 select S3C_DEV_NAND select S3C2410_IOTIMING if S3C2440_CPUFREQ select S3C2440_XTAL_16934400 + select S3C_ADC + select PDA_POWER + select BATTERY_S3C_ADC help Say Y here if you're using HP iPAQ rx1950
arch/arm/mach-s3c2440/mach-rx1950.c +160 -0
180 lines not on this page · raw message
Signature · 1 line
1.7.2.2
PATCH 1/3 rx1950: add battery device
Quoted 11 lines · Vasily Khoruzhick
Signed-off-by Vasily Khoruzhick <[email protected]>--- arch/arm/mach-s3c2440/Kconfig | 3 + arch/arm/mach-s3c2440/mach-rx1950.c | 160 +++++++++++++++++++++++++++++++++++ 2 files changed, 163 insertions(+), 0 deletions(-)arch/arm/mach-s3c2440/Kconfig +0
-0
arch/arm/mach-s3c2440/Kconfig config MACH_RX1950 · line 203
Quoted 6 lines
arch/arm/mach-s3c2440/Kconfig +3
-0@@ -198,6 +198,9 @@ config MACH_RX1950 select S3C_DEV_NAND select S3C2410_IOTIMING if S3C2440_CPUFREQ select S3C2440_XTAL_16934400 + select S3C_ADC + select PDA_POWER + select BATTERY_S3C_ADC
not keen on forcing these on unless they are required for the system to work.
Quoted 23 lines
arch/arm/mach-s3c2440/Kconfig +0
-0help Say Y here if you're using HP iPAQ rx1950arch/arm/mach-s3c2440/mach-rx1950.c +14
-0@@ -25,8 +25,10 @@ + +static const struct s3c_adc_bat_thresh bat_lut_noac[] = { + {4100 ,156 ,100 }, + {4050 ,156 ,95 }, + {4025 ,141 ,90 }, + {3995 ,144 ,85 }, + {3957 ,162 ,80 }, + {3931 ,147 ,75 }, + {3902 ,147 ,70 }, + {3863 ,153 ,65 }, + {3838 ,150 ,60 }, + {3800 ,153 ,55 }, + {3765 ,153 ,50 }, + {3748 ,172 ,45 },
arch/arm/mach-s3c2440/mach-rx1950.c static struct s3c2410fb_display rx1950_display = { · line 203
Quoted 10 lines
arch/arm/mach-s3c2440/mach-rx1950.c +10
-0+ {3740, 153, 40}, + {3714, 175, 35}, + {3710, 156, 30}, + {3963, 156, 25}, + {3672, 178, 20}, + {3651, 178, 15}, + {3629, 178, 10}, + {3612, 162, 5}, + {3605, 162, 0}, +
at least add a space after { and before }
it would be nice to have named initialisers.
PATCH 1/3 rx1950: add battery device
? ????????? ?? 8 ???????? 2010 02:06:19 ????? Ben Dooks ???????:
Quoted 19 lines · Vasily Khoruzhick
Quoted 18 lines
Signed-off-by Vasily Khoruzhick <[email protected]>---
arch/arm/mach-s3c2440/Kconfig | 3 + arch/arm/mach-s3c2440/mach-rx1950.c | 160+++++++++++++++++++++++++++++++++++ 2 files changed, 163 insertions(+), 0 deletions(-)
(quoted diff) +0
-0b/arch/arm/mach-s3c2440/Kconfig index cd8e7de..9b6b026 100644
arch/arm/mach-s3c2440/Kconfig +0
-0@@ -198,6 +198,9 @@ config MACH_RX1950 select S3C_DEV_NAND select S3C2410_IOTIMING if S3C2440_CPUFREQ select S3C2440_XTAL_16934400
Quoted 6 lines
arch/arm/mach-s3c2440/Kconfig config MACH_RX1950 · line 203
Quoted 3 lines
arch/arm/mach-s3c2440/Kconfig +3
-0+ select S3C_ADC + select PDA_POWER + select BATTERY_S3C_ADCnot keen on forcing these on unless they are required for the system to work.
Ok
Quoted 7 lines
arch/arm/mach-s3c2440/Kconfig config MACH_RX1950
Quoted 4 lines
arch/arm/mach-s3c2440/Kconfig +4
-0+ {3629, 178, 10}, + {3612, 162, 5}, + {3605, 162, 0}, +at least add a space after { and before }
it would be nice to have named initialisers.
Ok, I'll add named initialisers
Regards
Vasily
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 198 bytes
Desc: This is a digitally signed message part.
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20100908/c04cdb87/attachment.sig>
PATCH v2 1/3 rx1950: add battery device
In reply to Ben Dooksv2: don't force usage of battery driver,
use named initialisers in LUTs.
--- arch/arm/mach-s3c2440/mach-rx1950.c | 316 +++++++++++++++++++++++++++++++++++ 1 files changed, 316 insertions(+), 0 deletions(-)
arch/arm/mach-s3c2440/mach-rx1950.c +316 -0
@@ -25,8 +25,10 @@#include <linux/input.h> #include <linux/gpio_keys.h> #include <linux/sysdev.h> +#include <linux/pda_power.h> #include <linux/pwm_backlight.h> #include <linux/pwm.h> +#include <linux/s3c_adc_battery.h> #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h>
@@ -127,6 +129,318 @@ static struct s3c2410fb_display rx1950_display = { }; +static int power_supply_init (struct device *dev) +{ +return gpio_request (S3C2410_GPF (2 ),"cable plugged" ); +} + +static int rx1950_is_ac_online (void ) +{ +return !gpio_get_value (S3C2410_GPF (2 )); +} + +static void power_supply_exit (struct device *dev) +{ +gpio_free (S3C2410_GPF (2 )); +} + +static char *rx1950_supplicants[] = { +"main-battery" +}; + +static struct pda_power_pdata power_supply_info = { + .init = power_supply_init, + .is_ac_online = rx1950_is_ac_online, + .exit = power_supply_exit, + .supplied_to = rx1950_supplicants, + .num_supplicants =ARRAY_SIZE (rx1950_supplicants), +}; + +static struct resource power_supply_resources[] = { + [0 ] = { + .name ="ac" , + .flags =IORESOURCE_IRQ |IORESOURCE_IRQ_LOWEDGE | +IORESOURCE_IRQ_HIGHEDGE , + .start =IRQ_EINT2 , + .end =IRQ_EINT2 , + }, +}; + +static struct platform_device power_supply = { + .name ="pda-power" , + .id =-1 , + .dev = { + .platform_data = + &power_supply_info, + }, + .resource = power_supply_resources, + .num_resources =ARRAY_SIZE (power_supply_resources), +}; + +static const struct s3c_adc_bat_thresh bat_lut_noac[] = { + { + .volt =4100 , + .cur =156 , + .level =100 + }, + { + .volt =4050 , + .cur =156 , + .level =95 + }, + { + .volt =4025 , + .cur =141 , + .level =90 + }, + { + .volt =3995 , + .cur =144 , + .level =85 + }, + { + .volt =3957 , + .cur =162 , + .level =80 + }, + { + .volt =3931 , + .cur =147 , + .level =75 + }, + { + .volt =3902 , + .cur =147 , + .level =70 + }, + { + .volt =3863 , + .cur =153 , + .level =65 + }, + { + .volt =3838 , + .cur =150 , + .level =60 + }, + { + .volt =3800 , + .cur =153 , + .level =55 + }, + { + .volt =3765 , + .cur =153 , + .level =50 + }, + { + .volt =3748 , + .cur =172 , + .level =45 + }, + { + .volt =3740 , + .cur =153 , + .level =40 + }, + { + .volt =3714 , + .cur =175 , + .level =35 + }, + { + .volt =3710 , + .cur =156 , + .level =30 + }, + { + .volt =3963 , + .cur =156 , + .level =25 + }, + { + .volt =3672 , + .cur =178 , + .level =20 + }, + { + .volt =3651 , + .cur =178 , + .level =15 + }, + { + .volt =3629 , + .cur =178 , + .level =10 + }, + { + .volt =3612 , + .cur =162 , + .level =5 + }, + { + .volt =3605 , + .cur =162 , + .level =0 + }, +}; + +static const struct s3c_adc_bat_thresh bat_lut_acin[] = { + { + .volt =4200 , + .cur =0 , + .level =100 + }, + { + .volt =4190 , + .cur =0 , + .level =99 + }, + { + .volt =4178 , + .cur =0 , + .level =95 + }, + { + .volt =4110 , + .cur =0 , + .level =70 + }, + { + .volt =4076 , + .cur =0 , + .level =65 + }, + { + .volt =4046 , + .cur =0 , + .level =60 + }, + { + .volt =4021 , + .cur =0 , + .level =55 + }, + { + .volt =3999 , + .cur =0 , + .level =50 + }, + { + .volt =3982 , + .cur =0 , + .level =45 + }, + { + .volt =3965 , + .cur =0 , + .level =40 + }, + { + .volt =3957 , + .cur =0 , + .level =35 + }, + { + .volt =3948 , + .cur =0 , + .level =30 + }, + { + .volt =3936 , + .cur =0 , + .level =25 + }, + { + .volt =3927 , + .cur =0 , + .level =20 + }, + { + .volt =3906 , + .cur =0 , + .level =15 + }, + { + .volt =3880 , + .cur =0 , + .level =10 + }, + { + .volt =3829 , + .cur =0 , + .level =5 + }, + { + .volt =3820 , + .cur =0 , + .level =0 + }, +}; + +int rx1950_bat_init (void ) +{ +int ret; + + ret =gpio_request (S3C2410_GPJ (2 ),"rx1950-charger-enable-1" ); +if (ret) + goto err_gpio1; + ret =gpio_request (S3C2410_GPJ (3 ),"rx1950-charger-enable-2" ); +if (ret) + goto err_gpio2; + +return 0 ; + +err_gpio2: +gpio_free (S3C2410_GPJ (2 )); +err_gpio1: +return ret; +} + +void rx1950_bat_exit (void ) +{ +gpio_free (S3C2410_GPJ (2 )); +gpio_free (S3C2410_GPJ (3 )); +} + +void rx1950_enable_charger (void ) +{ +gpio_direction_output (S3C2410_GPJ (2 ),1 ); +gpio_direction_output (S3C2410_GPJ (3 ),1 ); +} + +void rx1950_disable_charger (void ) +{ +gpio_direction_output (S3C2410_GPJ (2 ),0 ); +gpio_direction_output (S3C2410_GPJ (3 ),0 ); +} + +static struct s3c_adc_bat_pdata rx1950_bat_cfg = { + .init = rx1950_bat_init, + .exit = rx1950_bat_exit, + .enable_charger = rx1950_enable_charger, + .disable_charger = rx1950_disable_charger, + .gpio_charge_finished =S3C2410_GPF (3 ), + .lut_noac = bat_lut_noac, + .lut_noac_cnt =ARRAY_SIZE (bat_lut_noac), + .lut_acin = bat_lut_acin, + .lut_acin_cnt =ARRAY_SIZE (bat_lut_acin), + .volt_channel =0 , + .current_channel =1 , + .volt_mult =4235 , + .current_mult =2900 , + .internal_impedance =200 , +}; + +static struct platform_device rx1950_battery = { + .name ="s3c-adc-battery" , + .id =-1 , + .dev = { + .parent = &s3c_device_adc.dev, + .platform_data = &rx1950_bat_cfg, + }, +}; +static struct s3c2410fb_mach_info rx1950_lcd_cfg = { .displays = &rx1950_display, .num_displays =1 ,
@@ -503,6 +817,8 @@ static struct platform_device *rx1950_devices[] __initdata = { &s3c_device_timer[1 ], &rx1950_backlight, &rx1950_device_gpiokeys, + &power_supply, + &rx1950_battery, }; static struct clk *rx1950_clocks[] __initdata = {
Signature · 1 line
1.7.2.2
PATCH v2 1/3 rx1950: add battery device
Quoted 2 lines · Vasily Khoruzhick
v2: don't force usage of battery driver,
use named initialisers in LUTs.
Any chance of more description here?
arch/arm/mach-s3c2440/mach-rx1950.c static struct s3c2410fb_display rx1950_display = { · line 185
Quoted 7 lines
arch/arm/mach-s3c2440/mach-rx1950.c +7
-0+ +static const struct s3c_adc_bat_thresh bat_lut_noac[] = { + { + .volt =4100 , + .cur =156 , + .level =100 + },
In this case I'd say we may as well do the following
{ .volt = 4100, .cur = 156, .level = 100 },given there so many of them.
Signature · 1 line
Ben
PATCH v3 1/3 rx1950: add battery device
This patch adds registration of appropriate device for s3c-adc-battery driver, so battery monitoring and charging are available on RX1950 PDA now.
---
v2: don't force usage of battery driver,
use named initialisers in LUTs.
v3: add comment to patch, make LUTs look tiny again.
arch/arm/mach-s3c2440/mach-rx1950.c | 160 +++++++++++++++++++++++++++++++++++ 1 files changed, 160 insertions(+), 0 deletions(-)
arch/arm/mach-s3c2440/mach-rx1950.c +160 -0
@@ -25,8 +25,10 @@#include <linux/input.h> #include <linux/gpio_keys.h> #include <linux/sysdev.h> +#include <linux/pda_power.h> #include <linux/pwm_backlight.h> #include <linux/pwm.h> +#include <linux/s3c_adc_battery.h> #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h>
@@ -127,6 +129,162 @@ static struct s3c2410fb_display rx1950_display = { }; +static int power_supply_init (struct device *dev) +{ +return gpio_request (S3C2410_GPF (2 ),"cable plugged" ); +} + +static int rx1950_is_ac_online (void ) +{ +return !gpio_get_value (S3C2410_GPF (2 )); +} + +static void power_supply_exit (struct device *dev) +{ +gpio_free (S3C2410_GPF (2 )); +} + +static char *rx1950_supplicants[] = { +"main-battery" +}; + +static struct pda_power_pdata power_supply_info = { + .init = power_supply_init, + .is_ac_online = rx1950_is_ac_online, + .exit = power_supply_exit, + .supplied_to = rx1950_supplicants, + .num_supplicants =ARRAY_SIZE (rx1950_supplicants), +}; + +static struct resource power_supply_resources[] = { + [0 ] = { + .name ="ac" , + .flags =IORESOURCE_IRQ |IORESOURCE_IRQ_LOWEDGE | +IORESOURCE_IRQ_HIGHEDGE , + .start =IRQ_EINT2 , + .end =IRQ_EINT2 , + }, +}; + +static struct platform_device power_supply = { + .name ="pda-power" , + .id =-1 , + .dev = { + .platform_data = + &power_supply_info, + }, + .resource = power_supply_resources, + .num_resources =ARRAY_SIZE (power_supply_resources), +}; + +static const struct s3c_adc_bat_thresh bat_lut_noac[] = { + { .volt =4100 , .cur =156 , .level =100 }, + { .volt =4050 , .cur =156 , .level =95 }, + { .volt =4025 , .cur =141 , .level =90 }, + { .volt =3995 , .cur =144 , .level =85 }, + { .volt =3957 , .cur =162 , .level =80 }, + { .volt =3931 , .cur =147 , .level =75 }, + { .volt =3902 , .cur =147 , .level =70 }, + { .volt =3863 , .cur =153 , .level =65 }, + { .volt =3838 , .cur =150 , .level =60 }, + { .volt =3800 , .cur =153 , .level =55 }, + { .volt =3765 , .cur =153 , .level =50 }, + { .volt =3748 , .cur =172 , .level =45 }, + { .volt =3740 , .cur =153 , .level =40 }, + { .volt =3714 , .cur =175 , .level =35 }, + { .volt =3710 , .cur =156 , .level =30 }, + { .volt =3963 , .cur =156 , .level =25 }, + { .volt =3672 , .cur =178 , .level =20 }, + { .volt =3651 , .cur =178 , .level =15 }, + { .volt =3629 , .cur =178 , .level =10 }, + { .volt =3612 , .cur =162 , .level =5 }, + { .volt =3605 , .cur =162 , .level =0 }, +}; + +static const struct s3c_adc_bat_thresh bat_lut_acin[] = { + { .volt =4200 , .cur =0 , .level =100 }, + { .volt =4190 , .cur =0 , .level =99 }, + { .volt =4178 , .cur =0 , .level =95 }, + { .volt =4110 , .cur =0 , .level =70 }, + { .volt =4076 , .cur =0 , .level =65 }, + { .volt =4046 , .cur =0 , .level =60 }, + { .volt =4021 , .cur =0 , .level =55 }, + { .volt =3999 , .cur =0 , .level =50 }, + { .volt =3982 , .cur =0 , .level =45 }, + { .volt =3965 , .cur =0 , .level =40 }, + { .volt =3957 , .cur =0 , .level =35 }, + { .volt =3948 , .cur =0 , .level =30 }, + { .volt =3936 , .cur =0 , .level =25 }, + { .volt =3927 , .cur =0 , .level =20 }, + { .volt =3906 , .cur =0 , .level =15 }, + { .volt =3880 , .cur =0 , .level =10 }, + { .volt =3829 , .cur =0 , .level =5 }, + { .volt =3820 , .cur =0 , .level =0 }, +}; + +int rx1950_bat_init (void ) +{ +int ret; + + ret =gpio_request (S3C2410_GPJ (2 ),"rx1950-charger-enable-1" ); +if (ret) + goto err_gpio1; + ret =gpio_request (S3C2410_GPJ (3 ),"rx1950-charger-enable-2" ); +if (ret) + goto err_gpio2; + +return 0 ; + +err_gpio2: +gpio_free (S3C2410_GPJ (2 )); +err_gpio1: +return ret; +} + +void rx1950_bat_exit (void ) +{ +gpio_free (S3C2410_GPJ (2 )); +gpio_free (S3C2410_GPJ (3 )); +} + +void rx1950_enable_charger (void ) +{ +gpio_direction_output (S3C2410_GPJ (2 ),1 ); +gpio_direction_output (S3C2410_GPJ (3 ),1 ); +} + +void rx1950_disable_charger (void ) +{ +gpio_direction_output (S3C2410_GPJ (2 ),0 ); +gpio_direction_output (S3C2410_GPJ (3 ),0 ); +} + +static struct s3c_adc_bat_pdata rx1950_bat_cfg = { + .init = rx1950_bat_init, + .exit = rx1950_bat_exit, + .enable_charger = rx1950_enable_charger, + .disable_charger = rx1950_disable_charger, + .gpio_charge_finished =S3C2410_GPF (3 ), + .lut_noac = bat_lut_noac, + .lut_noac_cnt =ARRAY_SIZE (bat_lut_noac), + .lut_acin = bat_lut_acin, + .lut_acin_cnt =ARRAY_SIZE (bat_lut_acin), + .volt_channel =0 , + .current_channel =1 , + .volt_mult =4235 , + .current_mult =2900 , + .internal_impedance =200 , +}; + +static struct platform_device rx1950_battery = { + .name ="s3c-adc-battery" , + .id =-1 , + .dev = { + .parent = &s3c_device_adc.dev, + .platform_data = &rx1950_bat_cfg, + }, +}; +static struct s3c2410fb_mach_info rx1950_lcd_cfg = { .displays = &rx1950_display, .num_displays =1 ,
@@ -503,6 +661,8 @@ static struct platform_device *rx1950_devices[] __initdata = { &s3c_device_timer[1 ], &rx1950_backlight, &rx1950_device_gpiokeys, + &power_supply, + &rx1950_battery, }; static struct clk *rx1950_clocks[] __initdata = {
Signature · 1 line
1.7.3
PATCH 2/3 rx1950: add LEDs support
In reply to Vasily Khoruzhick--- arch/arm/mach-s3c2440/mach-rx1950.c | 33 +++++++++++++++++++++++++++++++++ 1 files changed, 33 insertions(+), 0 deletions(-)
arch/arm/mach-s3c2440/mach-rx1950.c +33 -0
@@ -29,6 +29,7 @@#include <linux/pwm_backlight.h> #include <linux/pwm.h> #include <linux/s3c_adc_battery.h> +#include <linux/leds.h> #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h>
@@ -259,6 +260,37 @@ void rx1950_disable_charger(void)gpio_direction_output (S3C2410_GPJ (3 ),0 ); } +static struct gpio_led rx1950_leds_desc[] = { + { + .name ="Green" , + .default_trigger ="main-battery-charging-or-full" , + .gpio =S3C2410_GPA (6 ), + }, + { + .name ="Red" , + .default_trigger ="main-battery-full" , + .gpio =S3C2410_GPA (7 ), + }, + { + .name ="Blue" , + .default_trigger ="rx1950-acx-mem" , + .gpio =S3C2410_GPA (11 ), + }, +}; + +static struct gpio_led_platform_data rx1950_leds_pdata = { + .num_leds =ARRAY_SIZE (rx1950_leds_desc), + .leds = rx1950_leds_desc, +}; + +static struct platform_device rx1950_leds = { + .name ="leds-gpio" , + .id =-1 , + .dev = { + .platform_data = &rx1950_leds_pdata, + }, +}; +static struct s3c_adc_bat_pdata rx1950_bat_cfg = { .init = rx1950_bat_init, .exit = rx1950_bat_exit,
@@ -663,6 +695,7 @@ static struct platform_device *rx1950_devices[] __initdata = { &rx1950_device_gpiokeys, &power_supply, &rx1950_battery, + &rx1950_leds, }; static struct clk *rx1950_clocks[] __initdata = {
Signature · 1 line
1.7.2.2
PATCH 3/3 rx1950: add UDA1380 to i2c devices list
In reply to Vasily Khoruzhick--- arch/arm/mach-s3c2440/mach-rx1950.c | 25 +++++++++++++++++++------ 1 files changed, 19 insertions(+), 6 deletions(-)
arch/arm/mach-s3c2440/mach-rx1950.c +19 -6
@@ -30,6 +30,7 @@#include <linux/pwm.h> #include <linux/s3c_adc_battery.h> #include <linux/leds.h> +#include <linux/i2c.h> #include <linux/mtd/mtd.h> #include <linux/mtd/partitions.h>
@@ -58,6 +59,8 @@#include <plat/irq.h> #include <plat/ts.h> +#include <sound/uda1380.h> +#define LCD_PWM_PERIOD 192960#define LCD_PWM_DUTY 127353
@@ -671,11 +674,17 @@ static struct platform_device rx1950_device_gpiokeys = { .dev.platform_data = &rx1950_gpio_keys_data, }; -static struct s3c2410_platform_i2c rx1950_i2c_data = { - .flags =0 , - .slave_addr =0x42 , - .frequency =400 *1000 , - .sda_delay =S3C2410_IICLC_SDA_DELAY5 |S3C2410_IICLC_FILTER_ON , +static struct uda1380_platform_data uda1380_info = { + .gpio_power =S3C2410_GPJ (0 ), + .gpio_reset =S3C2410_GPD (0 ), + .dac_clk =UDA1380_DAC_CLK_SYSCLK , +}; + +static struct i2c_board_info rx1950_i2c_devices[] = { + { +I2C_BOARD_INFO ("uda1380" ,0x1a ), + .platform_data = &uda1380_info, + }, };static struct platform_device *rx1950_devices[]__initdata = {
@@ -683,6 +692,7 @@ static struct platform_device *rx1950_devices[] __initdata = { &s3c_device_wdt, &s3c_device_i2c0, &s3c_device_iis, + &s3c_device_pcm, &s3c_device_usbgadget, &s3c_device_rtc, &s3c_device_nand,
@@ -731,7 +741,7 @@ static void __init rx1950_init_machine(void)s3c24xx_udc_set_platdata (&rx1950_udc_cfg);s3c24xx_ts_set_platdata (&rx1950_ts_cfg);s3c24xx_mci_set_platdata (&rx1950_mmc_cfg); -s3c_i2c0_set_platdata (&rx1950_i2c_data); +s3c_i2c0_set_platdata (NULL );s3c_nand_set_platdata (&rx1950_nand_info);/* Turn off suspend on both USB ports, and switch the
@@ -762,6 +772,9 @@ static void __init rx1950_init_machine(void)WARN_ON (gpio_request (S3C2410_GPB (1 ),"LCD power" ));platform_add_devices (rx1950_devices,ARRAY_SIZE (rx1950_devices)); + +i2c_register_board_info (0 , rx1950_i2c_devices, +ARRAY_SIZE (rx1950_i2c_devices)); }/* H1940 and RX3715 need to reserve this for suspend */
Signature · 1 line
1.7.2.2
cover rx1950: add rest of devices
In reply to Vasily KhoruzhickQuoted 2 lines · Vasily Khoruzhick
This series adds battery device, LEDs device and sound codec device to
mach-rx1950.c
the first one has a few issues, the others look fine.