LCD on Zoom2 dev board with DSS
Subsystems (3)
Hi all,
I'm working on a zoom2 dev board (omap34x-II MDP). There is my actual config :
I've built kernel 2.6.35 from git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6.git
and then applied the following patchs :
[PATCH 1/2 V7] OMAP: ZOOM2/3&SDP3630: Add display board file for zoom boards <http://marc.info/?l=linux-omap&m=127445506720934&w=2>
[PATCH 2/2 V7] OMAP: ZOOM2/3&SDP3630: Add display board file for zoom boards <http://marc.info/?l=linux-omap&m=127445522921326&w=2>
[PATCH V6] OMAP: DSS: Add NEC NL8048HL11-01B display panel <http://marc.info/?l=linux-omap&m=127445535621669&w=2>
Finally I've enabled DSS and lcd NEC_NL8048HL11 in kernel config file.
At this time the kernel boots well, and my LCD backlight turns on but I can't see TUX while booting, and I can't draw anything after logging in. I've checked, the framebuffer device is present and configured with size of 800x480.
I've played with sys filesystem like on this wiki, but nothing happened:
<http://www.omappedia.org/wiki/Bootargs_for_enabling_display>
To enable DSS at boot time, I passed following boot options:
vram=10M omapdss.def_disp=lcd
Perhaps I've missed something?
Thank you in advance.
---
Yanick
Hi,
Quoted 4 lines · Yanick Saugy
Finally I've enabled DSS and lcd
NEC_NL8048HL11in kernel config file.At this time the kernel boots well, and my LCD backlight turns on but I can't see TUX while booting, and I can't draw anything after logging
to see tux you need to enable CONFIG_LOGO_LINUX_CLUT224 at least. Then you also might want to enable the framebuffer console, just to get some output on the screen.
Signature · 1 line
balbi
Hi,
I solved my problem. It appeared the PIN which controls LCD's reset signal (VGA_nRESET/h_GPIO_96) was not configured as a GPIO, and the driver tries to use it as GPIO, so the logical value was 0. We had to modify the OMAP MUX, and select this PIN (CAM_XCLKA) as an output GPIO (OMAP_MUX_MODE4).
Be aware of changing this PIN will probably disable the camera, because it was previously configured as a clock.
There is the patch for the LCD (diff -Naur):
--- a/arch/arm/mach-omap2/board-zoom2.c 2010-09-15 15:27:05.148399721
+0200
+++ b/arch/arm/mach-omap2/board-zoom2.c 2010-09-15 14:46:09.792900019
+0200
@@ -71,6 +71,7 @@
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
+ OMAP3_MUX(CAM_XCLKA, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#else
Quoted 26 lines · Yanick Saugy
Hi all,
I'm working on a zoom2 dev board (omap34x-II MDP). There is my actual config :
I've built kernel 2.6.35 from
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6.git
and then applied the following patchs :
[PATCH 1/2 V7] OMAP: ZOOM2/3&SDP3630: Add display board file for zoom boards <http://marc.info/?l=linux-omap&m=127445506720934&w=2>
[PATCH 2/2 V7] OMAP: ZOOM2/3&SDP3630: Add display board file for zoom boards <http://marc.info/?l=linux-omap&m=127445522921326&w=2>
[PATCH V6] OMAP: DSS: Add NEC NL8048HL11-01B display panel <http://marc.info/?l=linux-omap&m=127445535621669&w=2>Finally I've enabled DSS and lcd
NEC_NL8048HL11in kernel config file.At this time the kernel boots well, and my LCD backlight turns on but I can't see TUX while booting, and I can't draw anything after logging in. I've checked, the framebuffer device is present and configured with size of 800x480.
I've played with sys filesystem like on this wiki, but nothing happened:
<http://www.omappedia.org/wiki/Bootargs_for_enabling_display>To enable DSS at boot time, I passed following boot options:
vram=10M omapdss.def_disp=lcdPerhaps I've missed something?
Thank you in advance.
Quoted 7 lines
---
Yanick--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Tony Lindgren
maintainerQuoted 18 lines · Yanick Saugy
Hi,
I solved my problem. It appeared the PIN which controls LCD's reset signal (VGA_nRESET/h_GPIO_96) was not configured as a GPIO, and the driver tries to use it as GPIO, so the logical value was 0. We had to modify the OMAP MUX, and select this PIN (
CAM_XCLKA) as an output GPIO (OMAP_MUX_MODE4).Be aware of changing this PIN will probably disable the camera, because it was previously configured as a clock.
There is the patch for the LCD (diff -Naur):
---
a/arch/arm/mach-omap2/board-zoom2.c2010-09-15 15:27:05.148399721
+0200
+++b/arch/arm/mach-omap2/board-zoom2.c2010-09-15 14:46:09.792900019
+0200
Review line 77
Quoted 7 lines
(quoted diff) +1
-0@@ -71,6 +71,7 @@ #ifdef CONFIG_OMAP_MUX static struct omap_board_mux board_mux[] __initdata = { + OMAP3_MUX(CAM_XCLKA, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT), { .reg_offset = OMAP_MUX_TERMINATOR }, }; #else
Please repost with proper Signed-off-by. You might want to also Cc Tomi Valkeinen.
Regards,
Tony
PATCH 1/1 OMAP: ZOOM2: Change GPIO to enable LCD NEC NL8048HL11-01B on OMAP34x-II MDP
In reply to Yanick SaugyThe PIN which controls LCD's reset signal (VGA_nRESET/h_GPIO_96) was not configured as a GPIO. We had to modify the OMAP MUX, and select this PIN (CAM_XCLKA) as an output GPIO (OMAP_MUX_MODE4). (kernel 2.6.35)
Be aware of changing this PIN will probably disable the camera, because it was previously configured as a camera clock.
arch/arm/mach-omap2/board-zoom2.c 2010-09-15 14:46:09.792900019 +0200 renamed from arch/arm/mach-omap2/board-zoom2.c 2010-09-15 15:27:05.148399721 +0200 +2 -0
@@ -71,6 +71,7 @@ static struct twl4030_platform_data zoom #ifdef CONFIG_OMAP_MUX static struct omap_board_mux board_mux[] __initdata = { + OMAP3_MUX(CAM_XCLKA, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT), { .reg_offset = OMAP_MUX_TERMINATOR }, }; #else
@@ -82,6 +83,7 @@ static void __init omap_zoom2_init(void) omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); zoom_peripherals_init(); zoom_debugboard_init(); + zoom_display_init(OMAP_DSS_VENC_TYPE_COMPOSITE); } static void __init omap_zoom2_map_io(void)
Re: [PATCH] OMAP: ZOOM2: Change GPIO to enable LCD NEC NL8048HL11-01B on OMAP34x-II MDP
Quoted 9 lines · Yanick Saugy
The PIN which controls LCD's reset signal (VGA_nRESET/h_GPIO_96) was not configured as a GPIO. We had to modify the OMAP MUX, and select this PIN (
CAM_XCLKA) as an output GPIO (OMAP_MUX_MODE4). (kernel 2.6.35)Be aware of changing this PIN will probably disable the camera, because it was previously configured as a camera clock.
Signed-off-by Yanick Saugy <[email protected]>
I'm assuming Tomi is queuing this.
Quoted 26 lines
arch/arm/mach-omap2/board-zoom2.c 2010-09-15 14:46:09.792900019 +0200 renamed from arch/arm/mach-omap2/board-zoom2.c 2010-09-15 15:27:05.148399721 +0200 +2
-1@@ -71,6 +71,7 @@ static struct twl4030_platform_data zoom #ifdef CONFIG_OMAP_MUX static struct omap_board_mux board_mux[] __initdata = { + OMAP3_MUX(CAM_XCLKA, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT), { .reg_offset = OMAP_MUX_TERMINATOR }, }; #else@@ -82,6 +83,7 @@ static void __init omap_zoom2_init(void) omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); zoom_peripherals_init(); zoom_debugboard_init(); + zoom_display_init(OMAP_DSS_VENC_TYPE_COMPOSITE); } static void __init omap_zoom2_map_io(void) --To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [PATCH] OMAP: ZOOM2: Change GPIO to enable LCD NEC NL8048HL11-01B on OMAP34x-II MDP
In reply to Yanick SaugyHi,
Quoted 21 lines · ext Yanick Saugy
The PIN which controls LCD's reset signal (VGA_nRESET/h_GPIO_96) was not configured as a GPIO. We had to modify the OMAP MUX, and select this PIN (
CAM_XCLKA) as an output GPIO (OMAP_MUX_MODE4). (kernel 2.6.35)Be aware of changing this PIN will probably disable the camera, because it was previously configured as a camera clock.
Signed-off-by Yanick Saugy <[email protected]>arch/arm/mach-omap2/board-zoom2.c 2010-09-15 14:46:09.792900019 +0200 renamed from arch/arm/mach-omap2/board-zoom2.c 2010-09-15 15:27:05.148399721 +0200 +1
-0@@ -71,6 +71,7 @@ static struct twl4030_platform_data zoom #ifdef CONFIG_OMAP_MUX static struct omap_board_mux board_mux[] __initdata = { + OMAP3_MUX(CAM_XCLKA, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT), { .reg_offset = OMAP_MUX_TERMINATOR }, }; #else
arch/arm/mach-omap2/board-zoom2.c 2010-09-15 14:46:09.792900019 +0200 static void __init omap_zoom2_init(void) · line 89
Quoted 7 lines
arch/arm/mach-omap2/board-zoom2.c 2010-09-15 14:46:09.792900019 +0200 renamed from arch/arm/mach-omap2/board-zoom2.c 2010-09-15 15:27:05.148399721 +0200 +1
-0@@ -82,6 +83,7 @@ static void __init omap_zoom2_init(void) omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); zoom_peripherals_init(); zoom_debugboard_init(); + zoom_display_init(OMAP_DSS_VENC_TYPE_COMPOSITE); } static void __init omap_zoom2_map_io(void)
How did you create this patch? It doesn't look like standard one, and git am chokes on it. Also, it doesn't apply to the latest linux tree, so you need to rebase.
Tomi