Network Patchset v4
cover Network Patchset v4
We are close to the end of this journey. Several little problems were fixed and we are down to some little problems:
1 - jumbo test - tap interface name shouldn't be used to stablish arp static entry, use bridge name instead - need validation from akong and/or jasonwang
2 - vlan subtest - still has some problems with it
3 - ethtool - find a way to install ethtool in guest using distro packages - this one can be easily postponed
Please give me some feedback on it.
Amos Kong (11):
KVM test: Add a new macaddress pool algorithm
KVM test: Add a new subtest ping
KVM test: Add basic file transfer test
KVM test: Add a subtest of nic promisc
KVM test: Add a subtest of multicast
KVM test: Add a subtest of pxe
KVM test: Add a subtest of changing MAC address
KVM test: Add a netperf subtest
KVM test: kvm_utils - Add support of check if remote port free KVM test: Improve vlan subtest
KVM test: vlan subtest - Replace extra_params '-snapshot' with
image_snapshot
Lucas Meneghel Rodrigues (7):
KVM test: Make physical_resources_check to work with MAC management KVM test: Remove address_pools.cfg dependency
KVM test: Add a get_ifname function
KVM Test: Add nw related functions ping and get_linux_ifname KVM test: Add a subtest jumbo
KVM test: Add a subtest of load/unload nic driver
KVM test: Add subtest of testing offload by ethtool
client/tests/kvm/address_pools.cfg.sample | 65 ------ client/tests/kvm/control | 8 - client/tests/kvm/control.parallel | 9 - client/tests/kvm/get_started.py | 4 +- client/tests/kvm/kvm_test_utils.py | 130 ++++++++++++- client/tests/kvm/kvm_utils.py | 139 ++++++++++++- client/tests/kvm/kvm_vm.py | 104 +++++++++- client/tests/kvm/scripts/join_mcast.py | 37 ++++ client/tests/kvm/tests/ethtool.py | 222 ++++++++++++++++++++ client/tests/kvm/tests/file_transfer.py | 58 +++++ client/tests/kvm/tests/jumbo.py | 136 ++++++++++++ client/tests/kvm/tests/mac_change.py | 68 ++++++ client/tests/kvm/tests/multicast.py | 91 ++++++++ client/tests/kvm/tests/netperf.py | 56 +++++ client/tests/kvm/tests/nic_promisc.py | 103 +++++++++ client/tests/kvm/tests/nicdriver_unload.py | 115 ++++++++++ client/tests/kvm/tests/physical_resources_check.py | 7 +- client/tests/kvm/tests/ping.py | 72 +++++++ client/tests/kvm/tests/pxe.py | 31 +++ client/tests/kvm/tests/vlan.py | 186 ++++++++++++++++ client/tests/kvm/tests/vlan_tag.py | 68 ------ client/tests/kvm/tests_base.cfg.sample | 97 ++++++++- 22 files changed, 1628 insertions(+), 178 deletions(-) delete mode 100644 client/tests/kvm/address_pools.cfg.sample create mode 100755 client/tests/kvm/scripts/join_mcast.py create mode 100644 client/tests/kvm/tests/ethtool.py create mode 100644 client/tests/kvm/tests/file_transfer.py create mode 100644 client/tests/kvm/tests/jumbo.py create mode 100644 client/tests/kvm/tests/mac_change.py create mode 100644 client/tests/kvm/tests/multicast.py create mode 100644 client/tests/kvm/tests/netperf.py create mode 100644 client/tests/kvm/tests/nic_promisc.py create mode 100644 client/tests/kvm/tests/nicdriver_unload.py create mode 100644 client/tests/kvm/tests/ping.py create mode 100644 client/tests/kvm/tests/pxe.py create mode 100644 client/tests/kvm/tests/vlan.py delete mode 100644 client/tests/kvm/tests/vlan_tag.py
PATCH 1/18 KVM test: Add a new macaddress pool algorithm
From: Amos Kong <[email protected]>
Old method uses the addresses in the config files which could lead serious problem when multiple tests running in different hosts.
This patch adds a new macaddress pool algorithm, it generates the mac prefix based on mac address of the host, and fix it to correspond to IEEE802. When user have set the mac_prefix in the config file, we should use it instead of the dynamic generated mac prefix.
Add a parameter like 'preserve_mac', to preserve the original mac address, for things like migration.
MAC addresses are recorded into a dictionary 'address_pool' in following
format: {{'20100310-165222-Wt7l:0' : 'AE:9D:94:6A:9b:f9'},...}
20100310-165222-Wt7l : instance attribute of VM
0 : index of NIC
AE:9D:94:6A:9b:f9 : mac address
Use 'vm instance' + 'nic index' as the key, macaddress is the value.
Changes from v3:
- Generate prefix and suffixes using random.SystemRandom(), was having trouble generating truly random prefixes and suffixes only with random.randint().
Changes from v2:
- Instead of basing ourselves in a physical interface address to get an address prefix, just generate one with the prefix 0x9a (convention) randomly and add it to the address pool. If there's already one prefix, keep it there and just return it.
- Made messages more consistent and informative
- Made function names consistent all across the board
- Fixed some single line spacing between functions
Changs from v1:
- Use 'vm instance' + 'nic index' as the key of address_pool, address is value.
- Put 'mac_lock' and 'address_pool' to '/tmp', for sharing them to other autotest instances running on the same host.
- Change function names for less confusion.
- Do not copy 'vm.instance' in vm.clone()
- Split 'adding get_ifname function' to another patch
--- client/tests/kvm/kvm_utils.py | 116 ++++++++++++++++++++++++++++++++ client/tests/kvm/kvm_vm.py | 83 +++++++++++++++++++++-- client/tests/kvm/tests_base.cfg.sample | 2 +- 3 files changed, 195 insertions(+), 6 deletions(-)
client/tests/kvm/kvm_utils.py +116 -0
@@ -5,6 +5,7 @@ KVM test utility functions. """ import time, string, random, socket, os, signal, re, logging, commands, cPickle +import fcntl, shelve from autotest_lib.client.bin import utils from autotest_lib.client.common_lib import error, logging_config import kvm_subprocess
@@ -82,6 +83,121 @@ def get_sub_dict_names(dict, keyword): # Functions related to MAC/IP addresses +def _generate_mac_address_prefix(): + """ + Generate a MAC address prefix. By convention we will set KVM autotest + MAC addresses to start with 0x9a. + """ + r = random.SystemRandom() + l = [0x9a, r.randint(0x00, 0x7f), r.randint(0x00, 0x7f), + r.randint(0x00, 0xff)] + prefix = ':'.join(map(lambda x: "%02x" % x, l)) + ":" + return prefix + + +def generate_mac_address_prefix(): + """ + Generate a random MAC address prefix and add it to the MAC pool dictionary. + If there's a MAC prefix there already, do not update the MAC pool and just + return what's in there. + """ + lock_file = open("/tmp/mac_lock", 'w') + fcntl.lockf(lock_file.fileno() ,fcntl.LOCK_EX) + mac_pool = shelve.open("/tmp/address_pool", writeback=False) + + if mac_pool.get('prefix'): + prefix = mac_pool.get('prefix') + logging.debug('Retrieved previously generated MAC prefix for this ' + 'host: %s', prefix) + else: + prefix = _generate_mac_address_prefix() + mac_pool['prefix'] = prefix + logging.debug('Generated MAC address prefix for this host: %s', prefix) + + mac_pool.close() + fcntl.lockf(lock_file.fileno(), fcntl.LOCK_UN) + lock_file.close() + + return prefix + + +def generate_mac_address(root_dir, instance_vm, nic_index, prefix=None): + """ + Random generate a MAC address and add it to the MAC pool. + + Try to generate macaddress based on the mac address prefix, add it to a + dictionary 'address_pool'. + key = VM instance + nic index, value = mac address + {['20100310-165222-Wt7l:0'] : 'AE:9D:94:6A:9b:f9'} + + @param root_dir: Root dir for kvm. + @param instance_vm: Here we use instance of vm. + @param nic_index: The index of nic. + @param prefix: Prefix of MAC address. + @return: MAC address string. + """ + if prefix is None: + prefix = generate_mac_address_prefix() + + r = random.SystemRandom() + lock_file = open("/tmp/mac_lock", 'w') + fcntl.lockf(lock_file.fileno() ,fcntl.LOCK_EX) + mac_pool = shelve.open("/tmp/address_pool", writeback=False) + found = False + key = "%s:%s" % (instance_vm, nic_index) + + if mac_pool.get(key): + found = True + mac = mac_pool.get(key) + + while not found: + suffix = "%02x:%02x" % (r.randint(0x00,0xfe), + r.randint(0x00,0xfe)) + mac = prefix + suffix + mac_list = mac.split(":") + # Clear multicast bit + mac_list[0] = int(mac_list[0],16) & 0xfe + # Set local assignment bit (IEEE802) + mac_list[0] = mac_list[0] | 0x02 + mac_list[0] = "%02x" % mac_list[0] + mac = ":".join(mac_list) + if mac in [mac_pool.get(k) for k in mac_pool.keys()]: + continue + mac_pool[key] = mac + found = True + logging.debug("Generated MAC address for NIC %s: %s ", key, mac) + + mac_pool.close() + fcntl.lockf(lock_file.fileno(), fcntl.LOCK_UN) + lock_file.close() + return mac + + +def free_mac_address(root_dir, instance_vm, nic_index): + """ + Free mac address from address pool + + @param root_dir: Root dir for kvm + @param instance_vm: Here we use instance attribute of vm + @param nic_index: The index of nic + """ + lock_file = open("/tmp/mac_lock", 'w') + fcntl.lockf(lock_file.fileno() ,fcntl.LOCK_EX) + mac_pool = shelve.open("/tmp/address_pool", writeback=False) + key = "%s:%s" % (instance_vm, nic_index) + if not mac_pool or (not key in mac_pool.keys()): + logging.debug("NIC not present in the MAC pool, not modifying pool") + logging.debug("NIC: %s" % key) + logging.debug("Contents of MAC pool: %s" % mac_pool) + else: + logging.debug("Freeing MAC addr for NIC %s: %s", key, mac_pool[key]) + mac_pool.pop(key) + + mac_pool.close() + fcntl.lockf(lock_file.fileno(), fcntl.LOCK_UN) + lock_file.close() + + def mac_str_to_int(addr): """ Convert MAC address string to integer.
client/tests/kvm/kvm_vm.py +78 -5
151 lines not on this page · raw message
client/tests/kvm/tests_base.cfg.sample +1 -1
@@ -54,7 +54,7 @@ guest_port_remote_shell = 22 nic_mode = user #nic_mode = tap nic_script = scripts/qemu-ifup -address_index = 0 +#address_index = 0 run_tcpdump = yes # Misc
Signature · 1 line
1.7.1
PATCH 2/18 KVM test: Make physical_resources_check to work with MAC management
In reply to Lucas Meneghel RodriguesThe previous MAC address management breaks up the physical_resources_check test (the test picks up NIC MAC parameters from test parameters). Let's fix it by making it retrieve params from the method VM.get_mac_address()
--- client/tests/kvm/tests/physical_resources_check.py | 7 ++++++- 1 files changed, 6 insertions(+), 1 deletions(-)
client/tests/kvm/tests/physical_resources_check.py +6 -1
@@ -123,9 +123,14 @@ def run_physical_resources_check(test, params, env): found_mac_addresses = re.findall("macaddr=(\S+)", o) logging.debug("Found MAC adresses: %s" % found_mac_addresses) + nic_index = 0 for nic_name in kvm_utils.get_sub_dict_names(params, "nics"): nic_params = kvm_utils.get_sub_dict(params, nic_name) - mac, ip = kvm_utils.get_mac_ip_pair_from_dict(nic_params) + if "address_index" in nic_params: + mac, ip = kvm_utils.get_mac_ip_pair_from_dict(nic_params) + else: + mac = vm.get_mac_address(nic_index) + nic_index += 1 if not string.lower(mac) in found_mac_addresses: n_fail += 1 logging.error("MAC address mismatch:")
Signature · 1 line
1.7.1
PATCH 3/18 KVM test: Remove address_pools.cfg dependency
In reply to Lucas Meneghel RodriguesSince the previous patch introduces an automated management mechanism for MAC addresses, let's simplify things a bit by removing address_pools.cfg parsing from the control files, as well as just removing address_pools.cfg.sample.
--- client/tests/kvm/address_pools.cfg.sample | 65 ----------------------------- client/tests/kvm/control | 8 ---- client/tests/kvm/control.parallel | 9 ---- client/tests/kvm/get_started.py | 4 +- 4 files changed, 2 insertions(+), 84 deletions(-) delete mode 100644 client/tests/kvm/address_pools.cfg.sample
client/tests/kvm/address_pools.cfg.sample deleted +0 -65
@@ -1,65 +0,0 @@ -# Copy this file to address_pools.cfg and edit it. -# -# This file specifies several MAC-IP ranges for each host in the network that -# may run KVM tests. A MAC address must not be used twice, so these ranges -# must not overlap. The VMs running on each host will only use MAC addresses -# from the pool of that host. -# If you wish to use a static MAC-IP mapping, where each MAC address range is -# mapped to a known corresponding IP address range, specify the bases of the IP -# address ranges in this file. -# If you specify a MAC address range without a corresponding IP address range, -# the IP addresses for that range will be determined at runtime by listening -# to DHCP traffic using tcpdump. -# If you wish to determine IP addresses using tcpdump in any case, regardless -# of any # IP addresses specified in this file, uncomment the following line: -#always_use_tcpdump = yes -# You may also specify this parameter for specific hosts by adding it in the -# appropriate sections below. - -variants: - # Rename host1 to an actual (short) hostname in the network that will be running the Autotest client - - @host1: - # Add/remove ranges here - address_ranges = r1 r2 - - # Modify the following parameters to reflect the DHCP server's configuration - address_range_base_mac_r1 = 52:54:00:12:35:56 - #address_range_base_ip_r1 = 10.0.2.20 - address_range_size_r1 = 16 - - # Modify the following parameters to reflect the DHCP server's configuration - address_range_base_mac_r2 = 52:54:00:12:35:80 - #address_range_base_ip_r2 = 10.0.2.40 - address_range_size_r2 = 16 - - # Rename host2 to an actual (short) hostname in the network that will be running the Autotest client - - @host2: - # Add/remove ranges here - address_ranges = r1 r2 - - # Modify the following parameters to reflect the DHCP server's configuration - address_range_base_mac_r1 = 52:54:00:12:36:56 - #address_range_base_ip_r1 = 10.0.3.20 - address_range_size_r1 = 16 - - # Modify the following parameters to reflect the DHCP server's configuration - address_range_base_mac_r2 = 52:54:00:12:36:80 - #address_range_base_ip_r2 = 10.0.3.40 - address_range_size_r2 = 16 - - # Add additional hosts here... - - # This will be used for hosts that do not appear on the list - - @default_host: - # Add/remove ranges here - address_ranges = r1 r2 - - # Modify the following parameters to reflect the DHCP server's configuration - address_range_base_mac_r1 = 52:54:00:12:34:56 - #address_range_base_ip_r1 = 10.0.1.20 - address_range_size_r1 = 16 - - # Modify the following parameters to reflect the DHCP server's configuration - address_range_base_mac_r2 = 52:54:00:12:34:80 - #address_range_base_ip_r2 = 10.0.1.40 - address_range_size_r2 = 16
client/tests/kvm/control +0 -8
@@ -55,14 +55,6 @@ tests_cfg = kvm_config.config() tests_cfg_path = os.path.join(kvm_test_dir, "tests.cfg") tests_cfg.fork_and_parse(tests_cfg_path, str) -pools_cfg_path = os.path.join(kvm_test_dir, "address_pools.cfg") -tests_cfg.parse_file(pools_cfg_path) -hostname = os.uname()[1].split(".")[0] -if tests_cfg.count("^" + hostname): - tests_cfg.parse_string("only ^%s" % hostname) -else: - tests_cfg.parse_string("only ^default_host") - # Run the tests kvm_utils.run_tests(tests_cfg.get_generator(), job)
client/tests/kvm/control.parallel +0 -9
@@ -171,15 +171,6 @@ cfg = kvm_config.config() filename = os.path.join(pwd, "tests.cfg") cfg.fork_and_parse(filename, str) -filename = os.path.join(pwd, "address_pools.cfg") -if os.path.exists(filename): - cfg.parse_file(filename) - hostname = os.uname()[1].split(".")[0] - if cfg.count("^" + hostname): - cfg.parse_string("only ^%s" % hostname) - else: - cfg.parse_string("only ^default_host") - tests = cfg.get_list()
client/tests/kvm/get_started.py +2 -2
@@ -68,8 +68,8 @@ if __name__ == "__main__": "config samples to actual config files)") kvm_test_dir = os.path.dirname(sys.modules[__name__].__file__) kvm_test_dir = os.path.abspath(kvm_test_dir) - config_file_list = ["address_pools.cfg", "build.cfg", "cdkeys.cfg", - "tests_base.cfg", "tests.cfg", "unittests.cfg"] + config_file_list = ["build.cfg", "cdkeys.cfg", "tests_base.cfg", + "tests.cfg", "unittests.cfg"] for config_file in config_file_list: src_file = os.path.join(kvm_test_dir, "%s.sample" % config_file) dst_file = os.path.join(kvm_test_dir, config_file)
Signature · 1 line
1.7.1
PATCH 4/18 KVM test: Add a get_ifname function
In reply to Lucas Meneghel RodriguesIt's clearer to use 'nic_mode + nic_index + vnc_port' than 'tap0', It's also unique for one guest.
--- client/tests/kvm/kvm_vm.py | 21 ++++++++++++++++++++- 1 files changed, 20 insertions(+), 1 deletions(-)
client/tests/kvm/kvm_vm.py +20 -1
@@ -426,7 +426,7 @@ class VM: if tftp: tftp = kvm_utils.get_path(root_dir, tftp) qemu_cmd += add_net(help, vlan, nic_params.get("nic_mode", "user"), - nic_params.get("nic_ifname"), + self.get_ifname(vlan), script, downscript, tftp, nic_params.get("bootp"), redirs, self.netdev_id[vlan])
@@ -959,6 +959,25 @@ class VM: return self.redirs.get(port) + def get_ifname(self, nic_index=0): + """ + Return the ifname of tap device for the guest nic. + + The vnc_port is unique for each VM, nic_index is unique for each nic + of one VM, it can avoid repeated ifname. + + @param nic_index: Index of the NIC + """ + nics = kvm_utils.get_sub_dict_names(self.params, "nics") + nic_name = nics[nic_index] + nic_params = kvm_utils.get_sub_dict(self.params, nic_name) + if nic_params.get("nic_ifname"): + return nic_params.get("nic_ifname") + else: + return "%s_%s_%s" % (nic_params.get("nic_model"), + nic_index, self.vnc_port) + + def get_mac_address(self, nic_index=0): """ Return the macaddr of guest nic.
Signature · 1 line
1.7.1
PATCH 5/18 KVM Test: Add nw related functions ping and get_linux_ifname
In reply to Lucas Meneghel RodriguesAdd nw related functions ping and get_linux_ifname to kvm_test_utils.
Changes from v1:
- Use None to indicate that the session should be local in raw_ping
- Use session.sendline("\003") to send (ctrl+c) signal
- Use None to indicate that the session should be local
- Fix of coding style
--- client/tests/kvm/kvm_test_utils.py | 130 +++++++++++++++++++++++++++++++++++- 1 files changed, 129 insertions(+), 1 deletions(-)
client/tests/kvm/kvm_test_utils.py +129 -1
@@ -21,7 +21,7 @@ More specifically: @copyright: 2008-2009 Red Hat Inc. """ -import time, os, logging, re, commands +import time, os, logging, re, commands, signal from autotest_lib.client.common_lib import error from autotest_lib.client.bin import utils import kvm_utils, kvm_vm, kvm_subprocess, scan_results
@@ -505,3 +505,131 @@ def run_autotest(vm, session, control_path, timeout, outputdir): e_msg = ("Tests %s failed during control file execution" % " ".join(bad_results)) raise error.TestFail(e_msg) + + +def get_loss_ratio(output): + """ + Get the packet loss ratio from the output of ping +. + @param output: Ping output. + """ + try: + return int(re.findall('(\d+)% packet loss', output)[0]) + except IndexError: + logging.debug(output) + return -1 + + +def raw_ping(command, timeout, session, output_func): + """ + Low-level ping command execution. + + @param command: Ping command. + @param timeout: Timeout of the ping command. + @param session: Local executon hint or session to execute the ping command. + """ + if session is None: + process = kvm_subprocess.run_bg(command, output_func=output_func, + timeout=timeout) + + # Send SIGINT signal to notify the timeout of running ping process, + # Because ping have the ability to catch the SIGINT signal so we can + # always get the packet loss ratio even if timeout. + if process.is_alive(): + kvm_utils.kill_process_tree(process.get_pid(), signal.SIGINT) + + status = process.get_status() + output = process.get_output() + + process.close() + return status, output + else: + session.sendline(command) + status, output = session.read_up_to_prompt(timeout=timeout, + print_func=output_func) + if not status: + # Send ctrl+c (SIGINT) through ssh session + session.send("\003") + status, output2 = session.read_up_to_prompt(print_func=output_func) + output += output2 + if not status: + # We also need to use this session to query the return value + session.send("\003") + + session.sendline(session.status_test_command) + s2, o2 = session.read_up_to_prompt() + if not s2: + status = -1 + else: + try: + status = int(re.findall("\d+", o2)[0]) + except: + status = -1 + + return status, output + + +def ping(dest=None, count=None, interval=None, interface=None, + packetsize=None, ttl=None, hint=None, adaptive=False, + broadcast=False, flood=False, timeout=0, + output_func=logging.debug, session=None): + """ + Wrapper of ping. + + @param dest: Destination address. + @param count: Count of icmp packet. + @param interval: Interval of two icmp echo request. + @param interface: Specified interface of the source address. + @param packetsize: Packet size of icmp. + @param ttl: IP time to live. + @param hint: Path mtu discovery hint. + @param adaptive: Adaptive ping flag. + @param broadcast: Broadcast ping flag. + @param flood: Flood ping flag. + @param timeout: Timeout for the ping command. + @param output_func: Function used to log the result of ping. + @param session: Local executon hint or session to execute the ping command. + """ + if dest is not None: + command = "ping %s " % dest + else: + command = "ping localhost " + if count is not None: + command += " -c %s" % count + if interval is not None: + command += " -i %s" % interval + if interface is not None: + command += " -I %s" % interface + if packetsize is not None: + command += " -s %s" % packetsize + if ttl is not None: + command += " -t %s" % ttl + if hint is not None: + command += " -M %s" % hint + if adaptive: + command += " -A" + if broadcast: + command += " -b" + if flood: + command += " -f -q" + output_func = None + + return raw_ping(command, timeout, session, output_func) + + +def get_linux_ifname(session, mac_address): + """ + Get the interface name through the mac address. + + @param session: session to the virtual machine + @mac_address: the macaddress of nic + """ + + output = session.get_command_output("ifconfig -a") + + try: + ethname = re.findall("(\w+)\s+Link.*%s" % mac_address, output, + re.IGNORECASE)[0] + return ethname + except: + return None
Signature · 1 line
1.7.1
PATCH 6/18 KVM test: Add a new subtest ping
In reply to Lucas Meneghel RodriguesFrom: Amos Kong <[email protected]>
This test use ping to check the virtual nics, it contains two kinds of test:
1. Packet loss ratio test, ping the guest with different size of packets.
2. Stress test, flood ping guest then use ordinary ping to test the network.
We could not raise an error when flood ping failed, it's too strict. But we must check the ping result before/after flood-ping. The interval and packet size could be configurated through tests_base.cfg
Changes from v2:
- Coding style fixes
Changes from v1:
- Improve error message
--- client/tests/kvm/tests/ping.py | 72 ++++++++++++++++++++++++++++++++ client/tests/kvm/tests_base.cfg.sample | 5 ++ 2 files changed, 77 insertions(+), 0 deletions(-) create mode 100644 client/tests/kvm/tests/ping.py
client/tests/kvm/tests/ping.py new file +72 -0
@@ -0,0 +1,72 @@ +import logging +from autotest_lib.client.common_lib import error +import kvm_test_utils + + +def run_ping(test, params, env): + """ + Ping the guest with different size of packets. + + Packet Loss Test: + 1) Ping the guest with different size/interval of packets. + + Stress Test: + 1) Flood ping the guest. + 2) Check if the network is still usable. + + @param test: KVM test object. + @param params: Dictionary with the test parameters. + @param env: Dictionary with test environment. + """ + + vm = kvm_test_utils.get_living_vm(env, params.get("main_vm")) + session = kvm_test_utils.wait_for_login(vm) + + counts = params.get("ping_counts", 100) + flood_minutes = float(params.get("flood_minutes", 10)) + nics = params.get("nics").split() + strict_check = params.get("strict_check", "no") == "yes" + + packet_size = [0, 1, 4, 48, 512, 1440, 1500, 1505, 4054, 4055, 4096, 4192, + 8878, 9000, 32767, 65507] + + try: + for i, nic in enumerate(nics): + ip = vm.get_address(i) + if not ip: + logging.error("Could not get the ip of nic index %d", i) + continue + + for size in packet_size: + logging.info("Ping with packet size %s", size) + status, output = kvm_test_utils.ping(ip, 10, + packetsize=size, + timeout=20) + if strict_check: + ratio = kvm_test_utils.get_loss_ratio(output) + if ratio != 0: + raise error.TestFail("Loss ratio is %s for packet size" + " %s" % (ratio, size)) + else: + if status != 0: + raise error.TestFail("Ping failed, status: %s," + " output: %s" % (status, output)) + + logging.info("Flood ping test") + kvm_test_utils.ping(ip, None, flood=True, output_func=None, + timeout=flood_minutes * 60) + + logging.info("Final ping test") + status, output = kvm_test_utils.ping(ip, counts, + timeout=float(counts) * 1.5) + if strict_check: + ratio = kvm_test_utils.get_loss_ratio(output) + if ratio != 0: + raise error.TestFail("Ping failed, status: %s," + " output: %s" % (status, output)) + else: + if status != 0: + raise error.TestFail("Ping returns non-zero value %s" % + output) + finally: + session.close()
client/tests/kvm/tests_base.cfg.sample +5 -0
@@ -468,6 +468,11 @@ variants: kill_vm_gracefully_vm2 = no address_index_vm2 = 1 + - ping: install setup unattended_install.cdrom + type = ping + counts = 100 + flood_minutes = 10 + - physical_resources_check: install setup unattended_install.cdrom type = physical_resources_check catch_uuid_cmd = dmidecode | awk -F: '/UUID/ {print $2}'
Signature · 1 line
1.7.1
PATCH 7/18 KVM test: Add a subtest jumbo
In reply to Lucas Meneghel RodriguesAccording to different nic model set different MTU for it. And ping from guest to host, to see whether tested size can be received by host.
Changes from v3:
- The arp entry should be set with the bridge name, not the tap interface name
Changes from v2:
- Coding style fixes
Changes from v1:
- Make standard of lost ratio can be configured
--- client/tests/kvm/tests/jumbo.py | 136 ++++++++++++++++++++++++++++++++ client/tests/kvm/tests_base.cfg.sample | 11 +++- 2 files changed, 146 insertions(+), 1 deletions(-) create mode 100644 client/tests/kvm/tests/jumbo.py
client/tests/kvm/tests/jumbo.py new file +136 -0
@@ -0,0 +1,136 @@ +import logging, commands, random +from autotest_lib.client.common_lib import error +from autotest_lib.client.bin import utils +import kvm_test_utils, kvm_utils + +def run_jumbo(test, params, env): + """ + Test the RX jumbo frame function of vnics: + + 1) Boot the VM. + 2) Change the MTU of guest nics and host taps depending on the NIC model. + 3) Add the static ARP entry for guest NIC. + 4) Wait for the MTU ok. + 5) Verify the path MTU using ping. + 6) Ping the guest with large frames. + 7) Increment size ping. + 8) Flood ping the guest with large frames. + 9) Verify the path MTU. + 10) Recover the MTU. + + @param test: KVM test object. + @param params: Dictionary with the test parameters. + @param env: Dictionary with test environment. + """ + + vm = kvm_test_utils.get_living_vm(env, params.get("main_vm")) + session = kvm_test_utils.wait_for_login(vm) + mtu = params.get("mtu", "1500") + bridge = params.get("bridge", "") + if not bridge: + logging.warning('Bridge not defined on the config file, ' + 'trying to locate one with brctl...') + bridge_cmd = "/usr/sbin/brctl show | awk 'NR==2 { print $1 }'" + bridge = utils.system_output(bridge_cmd).strip() + flood_time = params.get("flood_time", "300") + max_icmp_pkt_size = int(mtu) - 28 + + ifname = vm.get_ifname(0) + ip = vm.get_address(0) + if ip is None: + raise error.TestError("Could not get the IP address") + + try: + # Environment preparation + ethname = kvm_test_utils.get_linux_ifname(session, vm.get_mac_address(0)) + + logging.info("Changing the MTU of guest ...") + guest_mtu_cmd = "ifconfig %s mtu %s" % (ethname , mtu) + s, o = session.get_command_status_output(guest_mtu_cmd) + if s != 0: + logging.error(o) + raise error.TestError("Fail to set the MTU of guest NIC: %s" % + ethname) + + logging.info("Chaning the MTU of host tap ...") + host_mtu_cmd = "ifconfig %s mtu %s" % (ifname, mtu) + utils.run(host_mtu_cmd) + + logging.info("Add a temporary static ARP entry ...") + arp_add_cmd = "arp -s %s %s -i %s" % (ip, vm.get_mac_address(0), bridge) + utils.run(arp_add_cmd) + + def is_mtu_ok(): + s, o = kvm_test_utils.ping(ip, 1, interface=ifname, + packetsize=max_icmp_pkt_size, + hint="do", timeout=2) + return s == 0 + + def verify_mtu(): + logging.info("Verify the path MTU") + s, o = kvm_test_utils.ping(ip, 10, interface=ifname, + packetsize=max_icmp_pkt_size, + hint="do", timeout=15) + if s != 0 : + logging.error(o) + raise error.TestFail("Path MTU is not as expected") + if kvm_test_utils.get_loss_ratio(o) != 0: + logging.error(o) + raise error.TestFail("Packet loss ratio during MTU " + "verification is not zero") + + def flood_ping(): + logging.info("Flood with large frames") + kvm_test_utils.ping(ip, interface=ifname, + packetsize=max_icmp_pkt_size, + flood=True, timeout=float(flood_time)) + + def large_frame_ping(count=100): + logging.info("Large frame ping") + s, o = kvm_test_utils.ping(ip, count, interface=ifname, + packetsize=max_icmp_pkt_size, + timeout=float(count) * 2) + ratio = kvm_test_utils.get_loss_ratio(o) + if ratio != 0: + raise error.TestFail("Loss ratio of large frame ping is %s" % + ratio) + + def size_increase_ping(step=random.randrange(90, 110)): + logging.info("Size increase ping") + for size in range(0, max_icmp_pkt_size + 1, step): + logging.info("Ping %s with size %s" % (ip, size)) + s, o = kvm_test_utils.ping(ip, 1, interface=ifname, + packetsize=size, + hint="do", timeout=1) + if s != 0: + s, o = kvm_test_utils.ping(ip, 10, interface=ifname, + packetsize=size, + adaptive=True, hint="do", + timeout=20) + + if kvm_test_utils.get_loss_ratio(o) > int(params.get( + "fail_ratio", 50)): + raise error.TestFail("Ping loss ratio is greater " + "than 50% for size %s" % size) + + logging.info("Waiting for the MTU to be OK") + wait_mtu_ok = 10 + if not kvm_utils.wait_for(is_mtu_ok, wait_mtu_ok, 0, 1): + logging.debug(commands.getoutput("ifconfig -a")) + raise error.TestError("MTU is not as expected even after %s " + "seconds" % wait_mtu_ok) + + # Functional Test + verify_mtu() + large_frame_ping() + size_increase_ping() + + # Stress test + flood_ping() + verify_mtu() + + finally: + # Environment clean + session.close() + logging.info("Removing the temporary ARP entry") + utils.run("arp -d %s -i %s" % (ip, bridge))
client/tests/kvm/tests_base.cfg.sample +10 -1
@@ -473,6 +473,9 @@ variants: counts = 100 flood_minutes = 10 + - jumbo: install setup unattended_install.cdrom + type = jumbo + - physical_resources_check: install setup unattended_install.cdrom type = physical_resources_check catch_uuid_cmd = dmidecode | awk -F: '/UUID/ {print $2}'
@@ -623,10 +626,16 @@ variants: variants: - @rtl8139: nic_model = rtl8139 + jumbo: + mtu = 1500 - e1000: nic_model = e1000 + jumbo: + mtu = 16110 - virtio_net: nic_model = virtio + jumbo: + mtu = 65520 # Guests
@@ -1241,7 +1250,7 @@ variants: # Windows section - @Windows: - no autotest linux_s3 vlan_tag ioquit unattended_install.(url|nfs|remote_ks) + no autotest linux_s3 vlan_tag ioquit unattended_install.(url|nfs|remote_ks) jumbo shutdown_command = shutdown /s /f /t 0 reboot_command = shutdown /r /f /t 0 status_test_command = echo %errorlevel%
Signature · 1 line
1.7.1
Re: [PATCH 07/18] KVM test: Add a subtest jumbo
O
Quoted 5 lines
client/tests/kvm/tests/jumbo.py new file +4
-0+ Test the RX jumbo frame function of vnics: + + 1) Boot the VM. + 2) Change the MTU of guest nics and host taps depending on theNIC model.
client/tests/kvm/tests/jumbo.py line 20
Quoted 9 lines
client/tests/kvm/tests/jumbo.py new file +9
-0+ 3) Add the static ARP entry for guest NIC. + 4) Wait for the MTU ok. + 5) Verify the path MTU using ping. + 6) Ping the guest with large frames. + 7) Increment size ping. + 8) Flood ping the guest with large frames. + 9) Verify the path MTU. + 10) Recover the MTU. +
Thanks for new set of patches.
Jumbo fails again since MTU is not as expected even.
02:46:14 INFO | Removing the temporary ARP entry 02:46:14 DEBUG| Running 'arp -d 10.168.0.6 -i kvmbr0' 02:46:14 ERROR| Test failed: TestError: MTU is not as expected even
after 10 seconds 02:46:14 DEBUG| Postprocessing VM 'vm2'... 02:46:14 DEBUG| VM object found in environment 02:46:14 DEBUG| Terminating screendump thread...
client/tests/kvm/tests/jumbo.py line 136
Quoted 3 lines
client/tests/kvm/tests/jumbo.py new file +2
-0+ logging.info("Removing the temporary ARP entry") + utils.run("arp -d %s -i %s" % (ip, bridge))
I am just trying to understand, why are we trying to remove same guest ip arp cache. For sure host ip will be there in arp cache. Try with host ip @eth*. It works fine for me.
Thanks
Pradeep
Re: [PATCH 07/18] KVM test: Add a subtest jumbo
Quoted 19 lines · pradeep
O
Quoted 5 lines
client/tests/kvm/tests/jumbo.py new file +4
-0+ Test the RX jumbo frame function of vnics: + + 1) Boot the VM. + 2) Change the MTU of guest nics and host taps depending on theNIC model.
client/tests/kvm/tests/jumbo.py line 20
Quoted 9 lines
client/tests/kvm/tests/jumbo.py new file +9
-0+ 3) Add the static ARP entry for guest NIC. + 4) Wait for the MTU ok. + 5) Verify the path MTU using ping. + 6) Ping the guest with large frames. + 7) Increment size ping. + 8) Flood ping the guest with large frames. + 9) Verify the path MTU. + 10) Recover the MTU. +Thanks for new set of patches.
Quoted 1 line
Jumbo fails again since MTU is not as expected even.
Not as expected even after 10 seconds. The idea is to change the MTU, wait a little while and check it again. Yes, I also got this problem doing my test of the patch. Need to check why that is happening.
Quoted 22 lines
02:46:14 INFO | Removing the temporary ARP entry 02:46:14 DEBUG| Running 'arp -d 10.168.0.6 -i kvmbr0' 02:46:14 ERROR| Test failed: TestError: MTU is not as expected evenafter 10 seconds 02:46:14 DEBUG| Postprocessing VM 'vm2'... 02:46:14 DEBUG| VM object found in environment 02:46:14 DEBUG| Terminating screendump thread...
client/tests/kvm/tests/jumbo.py line 136
Quoted 3 lines
client/tests/kvm/tests/jumbo.py new file +2
-0+ logging.info("Removing the temporary ARP entry") + utils.run("arp -d %s -i %s" % (ip, bridge))I am just trying to understand, why are we trying to remove same guest ip arp cache. For sure host ip will be there in arp cache. Try with host ip @eth*. It works fine for me.
Thanks
Pradeep
Re: [PATCH 07/18] KVM test: Add a subtest jumbo
Quoted 5 lines · On Wed, 29 Sep 2010 08:07:19 -0300 Lucas Meneghel Rodrigues <[email protected]>…
Not as expected even after 10 seconds. The idea is to change the MTU, wait a little while and check it again. Yes, I also got this problem doing my test of the patch. Need to check why that is happening.
from guest i tried to remove arp entry from cache as mentioned in code.
arp -d 10.168.0.6 -i kvmbr0
It never worked for me. I guess this is the reason for this error.
Quoted 11 lines
Quoted 5 lines
Thanks
Pradeep--
To unsubscribe from this list: send the line "unsubscribe kvm" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [PATCH 07/18] KVM test: Add a subtest jumbo
Quoted 10 lines · pradeep
Quoted 5 lines · On Wed, 29 Sep 2010 08:07:19 -0300 Lucas Meneghel Rodrigues <[email protected]>…
Not as expected even after 10 seconds. The idea is to change the MTU, wait a little while and check it again. Yes, I also got this problem doing my test of the patch. Need to check why that is happening.
Quoted 5 lines
from guest i tried to remove arp entry from cache as mentioned in code.
arp -d 10.168.0.6 -i kvmbr0
It never worked for me. I guess this is the reason for this error.
I spend some time on this test today and got it working. The bottom line is, we add a static arp cache entry for:
(IP of vm + MAC of vm interface) + corresponding tap interface
^ Guest side info ^ Host side info
If you issue a ifconfig on host while tests are running, you'll see the tap interface:
virtio_0_5900 Link encap:Ethernet HWaddr 8A:65:51:1F:6A:95
inet6 addr: fe80::8865:51ff:fe1f:6a95/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:65520 Metric:1
RX packets:560511 errors:0 dropped:0 overruns:0 frame:0
TX packets:565406 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:500
RX bytes:36697168035 (34.1 GiB) TX bytes:36697563087 (34.1 GiB)Then, if you run:
arp -s 10.16.74.148 9a:0b:5d:7a:e6:eb -i virtio_0_5900
It will work. Of course, the actual values of the ip and MAC addresses have to be checked on guest side.
I have rebased this test and re-sent. You might try it, but now I think it's going to work for you, as it did for me.
Moving closer to the completion of this patchset,
Lucas
Re: [PATCH 07/18] KVM test: Add a subtest jumbo
now jumbo tests works fine, since we added a static arp entry
thanks
Pradeep
PATCH 8/18 KVM test: Add basic file transfer test
In reply to Lucas Meneghel RodriguesFrom: Amos Kong <[email protected]>
This test is the basic test of transfering file between host and guest. Try to transfer a large file from host to guest, and transfer it back to host, then compare the files by calculate their md5 hash.
The default file size is 4000M, scp timeout is 1000s. It means if the average speed is less than 4M/s, this test will be fail. We can extend this test by using another disk later, then we can transfer larger files without the limit of first disk size.
Changes from v1:
- Use md5 to verify the integrity of files
- Try to use autotest API, such as, utils.system()
--- client/tests/kvm/tests/file_transfer.py | 58 +++++++++++++++++++++++++++++++ client/tests/kvm/tests_base.cfg.sample | 7 +++- 2 files changed, 64 insertions(+), 1 deletions(-) create mode 100644 client/tests/kvm/tests/file_transfer.py
client/tests/kvm/tests/file_transfer.py new file +58 -0
@@ -0,0 +1,58 @@ +import logging, commands, re +from autotest_lib.client.common_lib import error +from autotest_lib.client.bin import utils +import kvm_utils, kvm_test_utils + +def run_file_transfer(test, params, env): + """ + Test ethrnet device function by ethtool + + 1) Boot up a VM. + 2) Create a large file by dd on host. + 3) Copy this file from host to guest. + 4) Copy this file from guest to host. + 5) Check if file transfers ended good. + + @param test: KVM test object. + @param params: Dictionary with the test parameters. + @param env: Dictionary with test environment. + """ + vm = kvm_test_utils.get_living_vm(env, params.get("main_vm")) + timeout=int(params.get("login_timeout", 360)) + + logging.info("Trying to log into guest '%s' by serial", vm.name) + session = kvm_utils.wait_for(lambda: vm.serial_login(), + timeout, 0, step=2) + if not session: + raise error.TestFail("Could not log into guest '%s'" % vm.name) + + dir = test.tmpdir + scp_timeout = int(params.get("scp_timeout")) + cmd = "dd if=/dev/urandom of=%s/a.out bs=1M count=%d" % (dir, int( + params.get("filesize", 4000))) + + try: + logging.info("Create file by dd command on host, cmd: %s" % cmd) + utils.run(cmd) + + logging.info("Transfer file from host to guest") + if not vm.copy_files_to("%s/a.out" % dir, "/tmp/b.out", + timeout=scp_timeout): + raise error.TestFail("Fail to transfer file from host to guest") + + logging.info("Transfer file from guest to host") + if not vm.copy_files_from("/tmp/b.out", "%s/c.out" % dir, + timeout=scp_timeout): + raise error.TestFail("Fail to transfer file from guest to host") + + logging.debug(commands.getoutput("ls -l %s/[ac].out" % dir)) + md5_orig = utils.hash_file("%s/a.out" % dir, method="md5") + md5_new = utils.hash_file("%s/c.out" % dir, method="md5") + + if md5_orig != md5_new: + raise error.TestFail("File changed after transfer") + + finally: + session.get_command_status("rm -f /tmp/b.out") + utils.run("rm -f %s/[ac].out" % dir) + session.close()
client/tests/kvm/tests_base.cfg.sample +6 -1
@@ -476,6 +476,11 @@ variants: - jumbo: install setup unattended_install.cdrom type = jumbo + - file_transfer: install setup unattended_install.cdrom + type = file_transfer + filesize = 4000 + scp_timeout = 1000 + - physical_resources_check: install setup unattended_install.cdrom type = physical_resources_check catch_uuid_cmd = dmidecode | awk -F: '/UUID/ {print $2}'
@@ -1250,7 +1255,7 @@ variants: # Windows section - @Windows: - no autotest linux_s3 vlan_tag ioquit unattended_install.(url|nfs|remote_ks) jumbo + no autotest linux_s3 vlan_tag ioquit unattended_install.(url|nfs|remote_ks) jumbo file_transfer shutdown_command = shutdown /s /f /t 0 reboot_command = shutdown /r /f /t 0 status_test_command = echo %errorlevel%
Signature · 1 line
1.7.1
Re: [PATCH 08/18] KVM test: Add basic file transfer test
Quoted 12 lines · Lucas Meneghel Rodrigues
From: Amos Kong <[email protected]>
This test is the basic test of transfering file between host and guest. Try to transfer a large file from host to guest, and transfer it back to host, then compare the files by calculate their md5 hash.
The default file size is 4000M, scp timeout is 1000s. It means if the average speed is less than 4M/s, this test will be fail. We can extend
this test by using another disk later, then we can transfer larger files without the limit of first disk size.
Quoted 5 lines
Changes from v1:
- Use md5 to verify the integrity of files
- Try to use autotest API, such as,utils.system()Signed-off-by Amos Kong <[email protected]>
Why scp_timeout? Not transfer_timeout?
Is this really only scp file transfer to/from linux guest? Need to either name it so or generalize. Other things that need testing are NFS for linux guest, scp from windows, samba for linux and windows guests.
Quoted 42 lines
--- client/tests/kvm/tests/file_transfer.py | 58 +++++++++++++++++++++++++++++++ client/tests/kvm/tests_base.cfg.sample | 7 +++- 2 files changed, 64 insertions(+), 1 deletions(-) create mode 100644 client/tests/kvm/tests/file_transfer.pyclient/tests/kvm/tests/file_transfer.py new file +30
-0@@ -0,0 +1,58 @@ +import logging, commands, re +from autotest_lib.client.common_lib import error +from autotest_lib.client.bin import utils +import kvm_utils, kvm_test_utils + +def run_file_transfer(test, params, env): + """ + Test ethrnet device function by ethtool + + 1) Boot up a VM. + 2) Create a large file by dd on host. + 3) Copy this file from host to guest. + 4) Copy this file from guest to host. + 5) Check if file transfers ended good. + + @param test: KVM test object. + @param params: Dictionary with the test parameters. + @param env: Dictionary with test environment. + """ + vm = kvm_test_utils.get_living_vm(env, params.get("main_vm")) + timeout=int(params.get("login_timeout", 360)) + + logging.info("Trying to log into guest '%s' by serial", vm.name) + session = kvm_utils.wait_for(lambda: vm.serial_login(), + timeout, 0, step=2) + if not session: + raise error.TestFail("Could not log into guest '%s'" % vm.name) + + dir = test.tmpdir + scp_timeout = int(params.get("scp_timeout"))
client/tests/kvm/tests/file_transfer.py line 40
Quoted 10 lines
client/tests/kvm/tests/file_transfer.py new file +10
-0+ cmd = "dd if=/dev/urandom of=%s/a.out bs=1M count=%d" % (dir, int( + params.get("filesize", 4000))) + + try: + logging.info("Create file by dd command on host, cmd: %s" % cmd) + utils.run(cmd) + + logging.info("Transfer file from host to guest") + if not vm.copy_files_to("%s/a.out" % dir, "/tmp/b.out", + timeout=scp_timeout):
/tmp/b.out won't work on windows guest, will it?
maybe let guest select dest dir?
Quoted 50 lines
client/tests/kvm/tests/file_transfer.py new file +18
-0+ raise error.TestFail("Fail to transfer file from host to guest") + + logging.info("Transfer file from guest to host") + if not vm.copy_files_from("/tmp/b.out", "%s/c.out" % dir, + timeout=scp_timeout): + raise error.TestFail("Fail to transfer file from guest to host") + + logging.debug(commands.getoutput("ls -l %s/[ac].out" % dir)) + md5_orig = utils.hash_file("%s/a.out" % dir, method="md5") + md5_new = utils.hash_file("%s/c.out" % dir, method="md5") + + if md5_orig != md5_new: + raise error.TestFail("File changed after transfer") + + finally: + session.get_command_status("rm -f /tmp/b.out") + utils.run("rm -f %s/[ac].out" % dir) + session.close()client/tests/kvm/tests_base.cfg.sample +6
-1@@ -476,6 +476,11 @@ variants: - jumbo: install setup unattended_install.cdrom type = jumbo + - file_transfer: install setup unattended_install.cdrom + type = file_transfer + filesize = 4000 + scp_timeout = 1000 + - physical_resources_check: install setup unattended_install.cdrom type = physical_resources_check catch_uuid_cmd = dmidecode | awk -F: '/UUID/ {print $2}'@@ -1250,7 +1255,7 @@ variants: # Windows section - @Windows: - no autotest linux_s3 vlan_tag ioquit unattended_install.(url|nfs|remote_ks) jumbo + no autotest linux_s3 vlan_tag ioquit unattended_install.(url|nfs|remote_ks) jumbo file_transfer shutdown_command = shutdown /s /f /t 0 reboot_command = shutdown /r /f /t 0 status_test_command = echo %errorlevel%Signature · 6 lines
1.7.1 -- To unsubscribe from this list: send the line "unsubscribe kvm" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [PATCH 08/18] KVM test: Add basic file transfer test
Quoted 8 lines · On Tue, 28 Sep 2010 15:24:25 +0200 "Michael S. Tsirkin" <[email protected]> wrote:
Quoted 2 lines
Signed-off-by Amos Kong <[email protected]>Why
scp_timeout? Nottransfer_timeout?
Is this really only scp file transfer to/from linux guest? Need to either name it so or generalize. Other things that need testing are NFS for linux guest, scp from windows, samba for linux and windows guests.
too Agree with transfer_timeout
For now, this test fails. Looks like test case issue. Will figure out and send you a patch
Re: [PATCH 08/18] KVM test: Add basic file transfer test
Quoted 13 lines · pradeep
Quoted 8 lines · On Tue, 28 Sep 2010 15:24:25 +0200 "Michael S. Tsirkin" <[email protected]> wrote:
Quoted 2 lines
Signed-off-by Amos Kong <[email protected]>Why
scp_timeout? Nottransfer_timeout?
Is this really only scp file transfer to/from linux guest? Need to either name it so or generalize. Other things that need testing are NFS for linux guest, scp from windows, samba for linux and windows guests.
Quoted 4 lines
too Agree with
transfer_timeout
For now, this test fails. Looks like test case issue. Will figure out and send you a patch
This test didn't fail for me at all, it was working fine, both on my laptop and on my lab machine :s
Quoted 1 line
Re: [PATCH 08/18] KVM test: Add basic file transfer test
In reply to Michael S. TsirkinQuoted 17 lines · Michael S. Tsirkin
Quoted 16 lines · Lucas Meneghel Rodrigues
From: Amos Kong <[email protected]>
This test is the basic test of transfering file between host and guest. Try to transfer a large file from host to guest, and transfer it back to host, then compare the files by calculate their md5 hash.
The default file size is 4000M, scp timeout is 1000s. It means if the average speed is less than 4M/s, this test will be fail. We can extend
this test by using another disk later, then we can transfer larger files without the limit of first disk size.Changes from v1:
- Use md5 to verify the integrity of files
- Try to use autotest API, such as,utils.system()
Quoted 7 lines
Quoted 1 line
Signed-off-by Amos Kong <[email protected]>Why
scp_timeout? Nottransfer_timeout?
Is this really only scp file transfer to/from linux guest? Need to either name it so or generalize. Other things that need testing are NFS for linux guest, scp from windows, samba for linux and windows guests.
Ok, based on your comments, I've made the test more generic. Now the timeout is transfer_timeout, I created a variant called 'remote', that is supposed to use vm.copy_files_* methods, that are implemented for both windows and linux, and made things easy for people to implement new methods of doing this file transfer (nfs, samba, etc). As a bonus, now the test works on windows too :)
For now, there's only file_transfer.remote, that uses scp for linux, and rss transfer for windows. In case you don't know what rss is, is a remote shell server that was created for kvm autotest, since we had a lot of problems in the past getting openssh fully functional and working across all the windows versions. We found out that our own, simple remote shell server was way more effective to perform tests on windows.
http://autotest.kernel.org/browser/trunk/client/tests/kvm/deps/rss.cpp
I am running tests against some windows guests to make sure I got everything right, will publish the new version of the test when I'm done.
Re: [PATCH 08/18] KVM test: Add basic file transfer test
In reply to Michael S. TsirkinQuoted 17 lines · Michael S. Tsirkin
Quoted 16 lines · Lucas Meneghel Rodrigues
From: Amos Kong <[email protected]>
This test is the basic test of transfering file between host and guest. Try to transfer a large file from host to guest, and transfer it back to host, then compare the files by calculate their md5 hash.
The default file size is 4000M, scp timeout is 1000s. It means if the average speed is less than 4M/s, this test will be fail. We can extend
this test by using another disk later, then we can transfer larger files without the limit of first disk size.Changes from v1:
- Use md5 to verify the integrity of files
- Try to use autotest API, such as,utils.system()
Quoted 7 lines
Quoted 1 line
Signed-off-by Amos Kong <[email protected]>Why
scp_timeout? Nottransfer_timeout?
Is this really only scp file transfer to/from linux guest? Need to either name it so or generalize. Other things that need testing are NFS for linux guest, scp from windows, samba for linux and windows guests.
Ok, the new version of the test is ready. Here is the output of the tests under Fedora 13 64 bit and Windows 7 64 bit, conveniently trimmed down:
13:22:42 INFO | Creating 100MB file on host 13:22:42 DEBUG| Running 'dd if=/dev/urandom of=/root/autotest/client/tmp/tmpmOpO1z_kvm.smp2.Win7.64.file_transfer.remote/a.out bs=1M count=100' 13:22:56 INFO | Transfering file host -> guest, timeout: 1000s 13:23:04 INFO | File transfer host -> guest succeed, estimated throughput: 11.77MB/s 13:23:04 INFO | Transfering file guest -> host, timeout: 1000s 13:23:13 INFO | File transfer guest -> host succeed, estimated throughput: 11.59MB/s 13:23:13 DEBUG| Size of a.out: 104857600B 13:23:13 DEBUG| Size of c.out: 104857600B 13:23:13 INFO | Cleaning temp file on guest 13:23:13 DEBUG| Sending command: del C:\b.out 13:23:14 INFO | Cleaning temp files on host
13:12:28 INFO | Creating 100MB file on host 13:12:28 DEBUG| Running 'dd if=/dev/urandom of=/root/autotest/client/tmp/tmpp0B85Z_kvm.virtio_blk.smp2.Fedora.13.64.virtio_net.file_transfer.remote/a.out bs=1M count=100' 13:12:42 INFO | Transfering file host -> guest, timeout: 1000s 13:12:46 INFO | File transfer host -> guest succeed, estimated throughput: 25.41MB/s 13:12:46 INFO | Transfering file guest -> host, timeout: 1000s 13:12:50 INFO | File transfer guest -> host succeed, estimated throughput: 27.23MB/s 13:12:50 DEBUG| Size of a.out: 104857600B 13:12:50 DEBUG| Size of c.out: 104857600B 13:12:50 INFO | Cleaning temp file on guest 13:12:50 DEBUG| Sending command: rm -f /tmp/b.out 13:12:50 INFO | Cleaning temp files on host
I chose the file size 100MB just to test my changes, of course the default size is still 4000MB. I'll send the updated version of the test, won't send the full patchset again until the other issues are properly fixed.
If you guys are wondering why the difference in the throughput figures, well, I am also wondering. Maybe this is because windows is not using virtio, maybe rss is slower, I don't know yet.
Cheers,
Lucas
PATCH 9/18 KVM test: Add a subtest of load/unload nic driver
In reply to Lucas Meneghel RodriguesRepeatedly load/unload nic driver, try to transfer file between guest and host by threads at the same time, and check the md5sum.
Changes from v1:
- Use a new method to get nic driver name
- Use utils.hash_file() to get md5sum
--- client/tests/kvm/tests/nicdriver_unload.py | 115 ++++++++++++++++++++++++++++ client/tests/kvm/tests_base.cfg.sample | 10 ++- 2 files changed, 124 insertions(+), 1 deletions(-) create mode 100644 client/tests/kvm/tests/nicdriver_unload.py
client/tests/kvm/tests/nicdriver_unload.py new file +115 -0
@@ -0,0 +1,115 @@ +import logging, threading, os +from autotest_lib.client.common_lib import error +from autotest_lib.client.bin import utils +import kvm_utils, kvm_test_utils + +def run_nicdriver_unload(test, params, env): + """ + Test nic driver. + + 1) Boot a VM. + 2) Get the NIC driver name. + 3) Repeatedly unload/load NIC driver. + 4) Multi-session TCP transfer on test interface. + 5) Check whether the test interface should still work. + + @param test: KVM test object. + @param params: Dictionary with the test parameters. + @param env: Dictionary with test environment. + """ + timeout = int(params.get("login_timeout", 360)) + vm = kvm_test_utils.get_living_vm(env, params.get("main_vm")) + session = kvm_test_utils.wait_for_login(vm, timeout=timeout) + logging.info("Trying to log into guest '%s' by serial", vm.name) + session2 = kvm_utils.wait_for(lambda: vm.serial_login(), + timeout, 0, step=2) + if not session2: + raise error.TestFail("Could not log into guest '%s'" % vm.name) + + ethname = kvm_test_utils.get_linux_ifname(session, vm.get_mac_address(0)) + sys_path = "/sys/class/net/%s/device/driver" % (ethname) + s, o = session.get_command_status_output('readlink -e %s' % sys_path) + if s: + raise error.TestError("Could not find driver name") + driver = os.path.basename(o.strip()) + logging.info("driver is %s", driver) + + class ThreadScp(threading.Thread): + def run(self): + remote_file = '/tmp/' + self.getName() + file_list.append(remote_file) + ret = vm.copy_files_to(file_name, remote_file, timeout=scp_timeout) + if ret: + logging.debug("File %s was transfered successfuly", remote_file) + else: + logging.debug("Failed to transfer file %s", remote_file) + + def compare(origin_file, receive_file): + cmd = "md5sum %s" + check_sum1 = utils.hash_file(origin_file, method="md5") + s, output2 = session.get_command_status_output(cmd % receive_file) + if s != 0: + logging.error("Could not get md5sum of receive_file") + return False + check_sum2 = output2.strip().split()[0] + logging.debug("original file md5: %s, received file md5: %s", + check_sum1, check_sum2) + if check_sum1 != check_sum2: + logging.error("MD5 hash of origin and received files doesn't match") + return False + return True + + #produce sized file in host + file_size = params.get("file_size") + file_name = "/tmp/nicdriver_unload_file" + cmd = "dd if=/dev/urandom of=%s bs=%sM count=1" + utils.system(cmd % (file_name, file_size)) + + file_list = [] + connect_time = params.get("connect_time") + scp_timeout = int(params.get("scp_timeout")) + thread_num = int(params.get("thread_num")) + unload_load_cmd = ("sleep %s && ifconfig %s down && modprobe -r %s && " + "sleep 1 && modprobe %s && ifconfig %s up" % + (connect_time, ethname, driver, driver, ethname)) + pid = os.fork() + if pid != 0: + logging.info("Unload/load NIC driver repeatedly in guest...") + while True: + logging.debug("Try to unload/load nic drive once") + if session2.get_command_status(unload_load_cmd, timeout=120) != 0: + session.get_command_output("rm -rf /tmp/Thread-*") + raise error.TestFail("Unload/load nic driver failed") + pid, s = os.waitpid(pid, os.WNOHANG) + status = os.WEXITSTATUS(s) + if (pid, status) != (0, 0): + logging.debug("Child process ending") + break + else: + logging.info("Multi-session TCP data transfer") + threads = [] + for i in range(thread_num): + t = ThreadScp() + t.start() + threads.append(t) + for t in threads: + t.join(timeout = scp_timeout) + os._exit(0) + + session2.close() + + try: + logging.info("Check MD5 hash for received files in multi-session") + for f in file_list: + if not compare(file_name, f): + raise error.TestFail("Fail to compare (guest) file %s" % f) + + logging.info("Test nic function after load/unload") + if not vm.copy_files_to(file_name, file_name): + raise error.TestFail("Fail to copy file from host to guest") + if not compare(file_name, file_name): + raise error.TestFail("Test nic function after load/unload fail") + + finally: + session.get_command_output("rm -rf /tmp/Thread-*") + session.close()
client/tests/kvm/tests_base.cfg.sample +9 -1
@@ -481,6 +481,14 @@ variants: filesize = 4000 scp_timeout = 1000 + - nicdriver_unload: install setup unattended_install.cdrom + type = nicdriver_unload + nic_mode = tap + file_size = 100 + connect_time = 4 + scp_timeout = 300 + thread_num = 10 + - physical_resources_check: install setup unattended_install.cdrom type = physical_resources_check catch_uuid_cmd = dmidecode | awk -F: '/UUID/ {print $2}'
@@ -1255,7 +1263,7 @@ variants: # Windows section - @Windows: - no autotest linux_s3 vlan_tag ioquit unattended_install.(url|nfs|remote_ks) jumbo file_transfer + no autotest linux_s3 vlan_tag ioquit unattended_install.(url|nfs|remote_ks) jumbo file_transfer nicdriver_unload shutdown_command = shutdown /s /f /t 0 reboot_command = shutdown /r /f /t 0 status_test_command = echo %errorlevel%
Signature · 1 line
1.7.1
Re: [PATCH 09/18] KVM test: Add a subtest of load/unload nic driver
Quoted 84 lines · Lucas Meneghel Rodrigues
Repeatedly load/unload nic driver, try to transfer file between guest and host by threads at the same time, and check the md5sum.
Changes from v1:
- Use a new method to get nic driver name
- Useutils.hash_file()to get md5sumSigned-off-by Amos Kong <[email protected]>Signed-off-by Lucas Meneghel Rodrigues <[email protected]>--- client/tests/kvm/tests/nicdriver_unload.py | 115 ++++++++++++++++++++++++++++ client/tests/kvm/tests_base.cfg.sample | 10 ++- 2 files changed, 124 insertions(+), 1 deletions(-) create mode 100644 client/tests/kvm/tests/nicdriver_unload.pyclient/tests/kvm/tests/nicdriver_unload.py new file +63
-0@@ -0,0 +1,115 @@ +import logging, threading, os +from autotest_lib.client.common_lib import error +from autotest_lib.client.bin import utils +import kvm_utils, kvm_test_utils + +def run_nicdriver_unload(test, params, env): + """ + Test nic driver. + + 1) Boot a VM. + 2) Get the NIC driver name. + 3) Repeatedly unload/load NIC driver. + 4) Multi-session TCP transfer on test interface. + 5) Check whether the test interface should still work. + + @param test: KVM test object. + @param params: Dictionary with the test parameters. + @param env: Dictionary with test environment. + """ + timeout = int(params.get("login_timeout", 360)) + vm = kvm_test_utils.get_living_vm(env, params.get("main_vm")) + session = kvm_test_utils.wait_for_login(vm, timeout=timeout) + logging.info("Trying to log into guest '%s' by serial", vm.name) + session2 = kvm_utils.wait_for(lambda: vm.serial_login(), + timeout, 0, step=2) + if not session2: + raise error.TestFail("Could not log into guest '%s'" % vm.name) + + ethname = kvm_test_utils.get_linux_ifname(session, vm.get_mac_address(0)) + sys_path = "/sys/class/net/%s/device/driver" % (ethname) + s, o = session.get_command_status_output('readlink -e %s' % sys_path) + if s: + raise error.TestError("Could not find driver name") + driver = os.path.basename(o.strip()) + logging.info("driver is %s", driver) + + class ThreadScp(threading.Thread): + def run(self): + remote_file = '/tmp/' + self.getName() + file_list.append(remote_file) + ret = vm.copy_files_to(file_name, remote_file, timeout=scp_timeout) + if ret: + logging.debug("File %s was transfered successfuly", remote_file) + else: + logging.debug("Failed to transfer file %s", remote_file) + + def compare(origin_file, receive_file): + cmd = "md5sum %s" + check_sum1 = utils.hash_file(origin_file, method="md5") + s, output2 = session.get_command_status_output(cmd % receive_file) + if s != 0: + logging.error("Could not get md5sum of receive_file") + return False + check_sum2 = output2.strip().split()[0] + logging.debug("original file md5: %s, received file md5: %s", + check_sum1, check_sum2) + if check_sum1 != check_sum2: + logging.error("MD5 hash of origin and received files doesn't match") + return False + return True + + #produce sized file in host + file_size = params.get("file_size")
client/tests/kvm/tests/nicdriver_unload.py line 73
Quoted 10 lines
client/tests/kvm/tests/nicdriver_unload.py new file +10
-0+ file_name = "/tmp/nicdriver_unload_file" + cmd = "dd if=/dev/urandom of=%s bs=%sM count=1" + utils.system(cmd % (file_name, file_size)) + + file_list = [] + connect_time = params.get("connect_time") + scp_timeout = int(params.get("scp_timeout")) + thread_num = int(params.get("thread_num")) + unload_load_cmd = ("sleep %s && ifconfig %s down && modprobe -r %s && " + "sleep 1 && modprobe %s && ifconfig %s up" %
Need sleep some seconds (eg. 4s) between 'modprobe ..' and 'ifconfig .. up'. Because, the creation of interface maybe not complete when command('modprobe ..') returns.
unload_load_cmd = ("sleep %s && ifconfig %s down && modprobe -r %s && "
"sleep 1 && modprobe %s && sleep 4 && ifconfig %s up" %btw, lucas
I added comments to nicdriver_unload, vlan, multicast, ethtool. I also tested other patchsets, they are all fine.
Quoted 73 lines
client/tests/kvm/tests/nicdriver_unload.py new file +42
-0+ (connect_time, ethname, driver, driver, ethname)) + pid = os.fork() + if pid != 0: + logging.info("Unload/load NIC driver repeatedly in guest...") + while True: + logging.debug("Try to unload/load nic drive once") + if session2.get_command_status(unload_load_cmd, timeout=120) != 0: + session.get_command_output("rm -rf /tmp/Thread-*") + raise error.TestFail("Unload/load nic driver failed") + pid, s = os.waitpid(pid, os.WNOHANG) + status = os.WEXITSTATUS(s) + if (pid, status) != (0, 0): + logging.debug("Child process ending") + break + else: + logging.info("Multi-session TCP data transfer") + threads = [] + for i in range(thread_num): + t = ThreadScp() + t.start() + threads.append(t) + for t in threads: + t.join(timeout = scp_timeout) + os._exit(0) + + session2.close() + + try: + logging.info("Check MD5 hash for received files in multi-session") + for f in file_list: + if not compare(file_name, f): + raise error.TestFail("Fail to compare (guest) file %s" % f) + + logging.info("Test nic function after load/unload") + if not vm.copy_files_to(file_name, file_name): + raise error.TestFail("Fail to copy file from host to guest") + if not compare(file_name, file_name): + raise error.TestFail("Test nic function after load/unload fail") + + finally: + session.get_command_output("rm -rf /tmp/Thread-*") + session.close()client/tests/kvm/tests_base.cfg.sample +9
-1@@ -481,6 +481,14 @@ variants: filesize = 4000 scp_timeout = 1000 + - nicdriver_unload: install setup unattended_install.cdrom + type = nicdriver_unload + nic_mode = tap + file_size = 100 + connect_time = 4 + scp_timeout = 300 + thread_num = 10 + - physical_resources_check: install setup unattended_install.cdrom type = physical_resources_check catch_uuid_cmd = dmidecode | awk -F: '/UUID/ {print $2}'@@ -1255,7 +1263,7 @@ variants: # Windows section - @Windows: - no autotest linux_s3 vlan_tag ioquit unattended_install.(url|nfs|remote_ks) jumbo file_transfer + no autotest linux_s3 vlan_tag ioquit unattended_install.(url|nfs|remote_ks) jumbo file_transfer nicdriver_unload shutdown_command = shutdown /s /f /t 0 reboot_command = shutdown /r /f /t 0 status_test_command = echo %errorlevel%Signature · 1 line
1.7.1
PATCH 10/18 KVM test: Add a subtest of nic promisc
In reply to Lucas Meneghel RodriguesFrom: Amos Kong <[email protected]>
This test mainly covers TCP sent from host to guest and from guest to host with repeatedly turn on/off NIC promiscuous mode.
Changes from v1:
- Don't abruptly fail the whole test if we get a failure for a single size
--- client/tests/kvm/tests/nic_promisc.py | 103 ++++++++++++++++++++++++++++++++ client/tests/kvm/tests_base.cfg.sample | 6 ++- 2 files changed, 108 insertions(+), 1 deletions(-) create mode 100644 client/tests/kvm/tests/nic_promisc.py
client/tests/kvm/tests/nic_promisc.py new file +103 -0
@@ -0,0 +1,103 @@ +import logging +from autotest_lib.client.common_lib import error +from autotest_lib.client.bin import utils +import kvm_utils, kvm_test_utils + +def run_nic_promisc(test, params, env): + """ + Test nic driver in promisc mode: + + 1) Boot up a VM. + 2) Repeatedly enable/disable promiscuous mode in guest. + 3) TCP data transmission from host to guest, and from guest to host, + with 1/1460/65000/100000000 bytes payloads. + 4) Clean temporary files. + 5) Stop enable/disable promiscuous mode change. + + @param test: KVM test object. + @param params: Dictionary with the test parameters. + @param env: Dictionary with test environment. + """ + timeout = int(params.get("login_timeout", 360)) + vm = kvm_test_utils.get_living_vm(env, params.get("main_vm")) + session = kvm_test_utils.wait_for_login(vm, timeout=timeout) + + logging.info("Trying to log into guest '%s' by serial", vm.name) + session2 = kvm_utils.wait_for(lambda: vm.serial_login(), + timeout, 0, step=2) + if not session2: + raise error.TestFail("Could not log into guest '%s'" % vm.name) + + def compare(filename): + cmd = "md5sum %s" % filename + md5_host = utils.hash_file(filename, method="md5") + rc_guest, md5_guest = session.get_command_status_output(cmd) + if rc_guest: + logging.debug("Could not get MD5 hash for file %s on guest," + "output: %s", filename, md5_guest) + return False + md5_guest = md5_guest.split()[0] + if md5_host != md5_guest: + logging.error("MD5 hash mismatch between file %s " + "present on guest and on host", filename) + logging.error("MD5 hash for file on guest: %s," + "MD5 hash for file on host: %s", md5_host, md5_guest) + return False + return True + + ethname = kvm_test_utils.get_linux_ifname(session, vm.get_mac_address(0)) + set_promisc_cmd = ("ip link set %s promisc on; sleep 0.01;" + "ip link set %s promisc off; sleep 0.01" % + (ethname, ethname)) + logging.info("Set promisc change repeatedly in guest") + session2.sendline("while true; do %s; done" % set_promisc_cmd) + + dd_cmd = "dd if=/dev/urandom of=%s bs=%d count=1" + filename = "/tmp/nic_promisc_file" + file_size = params.get("file_size", "1, 1460, 65000, 100000000").split(",") + success_counter = 0 + try: + for size in file_size: + logging.info("Create %s bytes file on host" % size) + utils.run(dd_cmd % (filename, int(size))) + + logging.info("Transfer file from host to guest") + if not vm.copy_files_to(filename, filename): + logging.error("File transfer failed") + continue + if not compare(filename): + logging.error("Compare file failed") + continue + else: + success_counter += 1 + + logging.info("Create %s bytes file on guest" % size) + if session.get_command_status(dd_cmd % (filename, int(size)), + timeout=100) != 0: + logging.error("Create file on guest failed") + continue + + logging.info("Transfer file from guest to host") + if not vm.copy_files_from(filename, filename): + logging.error("File transfer failed") + continue + if not compare(filename): + logging.error("Compare file failed") + continue + else: + success_counter += 1 + + logging.info("Clean temporary files") + cmd = "rm -f %s" % filename + utils.run(cmd) + session.get_command_status(cmd) + + finally: + logging.info("Restore the %s to the nonpromisc mode", ethname) + session2.close() + session.get_command_status("ip link set %s promisc off" % ethname) + session.close() + + if success_counter != 2 * len(file_size): + raise error.TestFail("Some tests failed, succss_ratio : %s/%s" % + (success_counter, len(file_size)))
client/tests/kvm/tests_base.cfg.sample +5 -1
@@ -489,6 +489,10 @@ variants: scp_timeout = 300 thread_num = 10 + - nic_promisc: install setup unattended_install.cdrom + type = nic_promisc + file_size = 1, 1460, 65000, 100000000 + - physical_resources_check: install setup unattended_install.cdrom type = physical_resources_check catch_uuid_cmd = dmidecode | awk -F: '/UUID/ {print $2}'
@@ -1263,7 +1267,7 @@ variants: # Windows section - @Windows: - no autotest linux_s3 vlan_tag ioquit unattended_install.(url|nfs|remote_ks) jumbo file_transfer nicdriver_unload + no autotest linux_s3 vlan_tag ioquit unattended_install.(url|nfs|remote_ks) jumbo file_transfer nicdriver_unload nic_promisc shutdown_command = shutdown /s /f /t 0 reboot_command = shutdown /r /f /t 0 status_test_command = echo %errorlevel%
Signature · 1 line
1.7.1
PATCH 11/18 KVM test: Add a subtest of multicast
In reply to Lucas Meneghel RodriguesFrom: Amos Kong <[email protected]>
Use 'ping' to test send/recive multicat packets. Flood ping test is also added. Limit guest network as 'bridge' mode, because multicast packets could not be transmitted to guest when using 'user' network.
Add join_mcast.py for joining machine into multicast groups.
Changes from v1:
- Just flush the firewall rules with iptables -F
--- client/tests/kvm/scripts/join_mcast.py | 37 +++++++++++++ client/tests/kvm/tests/multicast.py | 91 ++++++++++++++++++++++++++++++++ client/tests/kvm/tests_base.cfg.sample | 9 +++- 3 files changed, 136 insertions(+), 1 deletions(-) create mode 100755 client/tests/kvm/scripts/join_mcast.py create mode 100644 client/tests/kvm/tests/multicast.py
client/tests/kvm/scripts/join_mcast.py new file +37 -0
@@ -0,0 +1,37 @@ +#!/usr/bin/python +import socket, struct, os, signal, sys +# -*- coding: utf-8 -*- + +""" +Script used to join machine into multicast groups. + +@author Amos Kong <[email protected]> +""" + +if __name__ == "__main__": + if len(sys.argv) < 4: + print """%s [mgroup_count] [prefix] [suffix] + mgroup_count: count of multicast addresses + prefix: multicast address prefix + suffix: multicast address suffix""" % sys.argv[0] + sys.exit() + + mgroup_count = int(sys.argv[1]) + prefix = sys.argv[2] + suffix = int(sys.argv[3]) + + s = socket.socket(socket.AF_INET, socket.SOCK_DGRAM) + for i in range(mgroup_count): + mcast = prefix + "." + str(suffix + i) + try: + mreq = struct.pack("4sl", socket.inet_aton(mcast), + socket.INADDR_ANY) + s.setsockopt(socket.IPPROTO_IP, socket.IP_ADD_MEMBERSHIP, mreq) + except: + s.close() + print "Could not join multicast: %s" % mcast + raise + + print "join_mcast_pid:%s" % os.getpid() + os.kill(os.getpid(), signal.SIGSTOP) + s.close()
client/tests/kvm/tests/multicast.py new file +91 -0
91 lines not on this page · raw message
client/tests/kvm/tests_base.cfg.sample +8 -1
@@ -493,6 +493,13 @@ variants: type = nic_promisc file_size = 1, 1460, 65000, 100000000 + - multicast: install setup unattended_install.cdrom + type = multicast + nic_mode = tap + mcast = 225.0.0.1 + mgroup_count = 20 + flood_minutes = 1 + - physical_resources_check: install setup unattended_install.cdrom type = physical_resources_check catch_uuid_cmd = dmidecode | awk -F: '/UUID/ {print $2}'
@@ -1267,7 +1274,7 @@ variants: # Windows section - @Windows: - no autotest linux_s3 vlan_tag ioquit unattended_install.(url|nfs|remote_ks) jumbo file_transfer nicdriver_unload nic_promisc + no autotest linux_s3 vlan_tag ioquit unattended_install.(url|nfs|remote_ks) jumbo file_transfer nicdriver_unload nic_promisc multicast shutdown_command = shutdown /s /f /t 0 reboot_command = shutdown /r /f /t 0 status_test_command = echo %errorlevel%
Signature · 1 line
1.7.1
Re: [PATCH 11/18] KVM test: Add a subtest of multicast
Quoted 10 lines · On Mon, 27 Sep 2010 18:43:57 -0400 Lucas Meneghel Rodrigues <[email protected]>…
From: Amos Kong <[email protected]>
Use 'ping' to test send/recive multicat packets. Flood ping test is also added. Limit guest network as 'bridge' mode, because multicast packets could not be transmitted to guest when using 'user' network. Add
join_mcast.pyfor joining machine into multicast groups.Changes from v1:
- Just flush the firewall rules with iptables -F
After copying join_mcast.py to guest, autotest fails to run the below command.
05:22:56 DEBUG| Sending command: python /tmp/join_mcast.py 20 225.0.0 1 05:22:56 DEBUG| Command failed; status: 147, output:
join_mcast_pid:12727
[1]+ Stopped python /tmp/join_mcast.py 20 225.0.0 1
00:17:31 DEBUG| Sending command: kill -s SIGCONT 2005 00:17:31 ERROR| Test failed: TestFail: Ping return non-zero value PING 225.0.0.1 (225.0.0.1) from 9.126.89.203 rtl8139_0_5900: 56(84) bytes of data.
Re: [PATCH 11/18] KVM test: Add a subtest of multicast
In reply to Lucas Meneghel RodriguesQuoted 100 lines · Lucas Meneghel Rodrigues
From: Amos Kong <[email protected]>
Use 'ping' to test send/recive multicat packets. Flood ping test is also added. Limit guest network as 'bridge' mode, because multicast packets could not be transmitted to guest when using 'user' network.
Addjoin_mcast.pyfor joining machine into multicast groups.Changes from v1:
- Just flush the firewall rules with iptables -FSigned-off-by Amos Kong <[email protected]>--- client/tests/kvm/scripts/join_mcast.py | 37 +++++++++++++ client/tests/kvm/tests/multicast.py | 91 ++++++++++++++++++++++++++++++++ client/tests/kvm/tests_base.cfg.sample | 9 +++- 3 files changed, 136 insertions(+), 1 deletions(-) create mode 100755 client/tests/kvm/scripts/join_mcast.py create mode 100644 client/tests/kvm/tests/multicast.pyclient/tests/kvm/scripts/join_mcast.py new file +37
-0@@ -0,0 +1,37 @@ +#!/usr/bin/python +import socket, struct, os, signal, sys +# -*- coding: utf-8 -*- + +""" +Script used to join machine into multicast groups. + +@author Amos Kong <[email protected]> +""" + +if __name__ == "__main__": + if len(sys.argv) < 4: + print """%s [mgroup_count] [prefix] [suffix] + mgroup_count: count of multicast addresses + prefix: multicast address prefix + suffix: multicast address suffix""" % sys.argv[0] + sys.exit() + + mgroup_count = int(sys.argv[1]) + prefix = sys.argv[2] + suffix = int(sys.argv[3]) + + s = socket.socket(socket.AF_INET, socket.SOCK_DGRAM) + for i in range(mgroup_count): + mcast = prefix + "." + str(suffix + i) + try: + mreq = struct.pack("4sl", socket.inet_aton(mcast), + socket.INADDR_ANY) + s.setsockopt(socket.IPPROTO_IP, socket.IP_ADD_MEMBERSHIP, mreq) + except: + s.close() + print "Could not join multicast: %s" % mcast + raise + + print "join_mcast_pid:%s" % os.getpid() + os.kill(os.getpid(), signal.SIGSTOP) + s.close()client/tests/kvm/tests/multicast.py new file +32
-0@@ -0,0 +1,91 @@ +import logging, os, re +from autotest_lib.client.common_lib import error +from autotest_lib.client.bin import utils +import kvm_test_utils + + +def run_multicast(test, params, env): + """ + Test multicast function of nic (rtl8139/e1000/virtio) + + 1) Create a VM. + 2) Join guest into multicast groups. + 3) Ping multicast addresses on host. + 4) Flood ping test with different size of packets. + 5) Final ping test and check if lose packet. + + @param test: KVM test object. + @param params: Dictionary with the test parameters. + @param env: Dictionary with test environment. + """ + vm = kvm_test_utils.get_living_vm(env, params.get("main_vm")) + session = kvm_test_utils.wait_for_login(vm, + timeout=int(params.get("login_timeout", 360))) + + def run_guest(cmd): + s, o = session.get_command_status_output(cmd) + if s: + logging.warning('Command %s executed in guest returned exit code ' + '%s, output: %s', cmd, s, o.strip()) + + def run_host_guest(cmd): + run_guest(cmd)
client/tests/kvm/tests/multicast.py line 42
Quoted 10 lines
client/tests/kvm/tests/multicast.py new file +10
-0+ utils.system(cmd, ignore_status=True) + + # flush the firewall rules + cmd_flush = "iptables -F" + cmd_selinux = ("if [ -e /selinux/enforce ]; then setenforce 0; " + "else echo 'no /selinux/enforce file present'; fi") + run_host_guest(cmd_flush) + run_host_guest(cmd_selinux) + # make sure guest replies to broadcasts + cmd_broadcast = "echo 0 > /proc/sys/net/ipv4/icmp_echo_ignore"
Hello pradeep, thanks for your test, it's caused by this error
cmd_broadcast = "echo 0 > /proc/sys/net/ipv4/icmp_echo_ignore_broadcasts"
Quoted 79 lines
client/tests/kvm/tests/multicast.py new file +49
-0+ cmd_broadcast_2 = "echo 0 > /proc/sys/net/ipv4/icmp_echo_ignore_all" + run_guest(cmd_broadcast) + run_guest(cmd_broadcast_2) + + # base multicast address + mcast = params.get("mcast", "225.0.0.1") + # count of multicast addresses, less than 20 + mgroup_count = int(params.get("mgroup_count", 5)) + flood_minutes = float(params.get("flood_minutes", 10)) + ifname = vm.get_ifname() + prefix = re.findall("\d+.\d+.\d+", mcast)[0] + suffix = int(re.findall("\d+", mcast)[-1]) + # copy python script to guest for joining guest to multicast groups + mcast_path = os.path.join(test.bindir, "scripts/join_mcast.py") + if not vm.copy_files_to(mcast_path, "/tmp"): + raise error.TestError("Fail to copy %s to guest" % mcast_path) + output = session.get_command_output("python /tmp/join_mcast.py %d %s %d" % + (mgroup_count, prefix, suffix)) + + # if success to join multicast, the process will be paused, and return PID. + try: + pid = re.findall("join_mcast_pid:(\d+)", output)[0] + except IndexError: + raise error.TestFail("Can't join multicast groups,output:%s" % output) + + try: + for i in range(mgroup_count): + new_suffix = suffix + i + mcast = "%s.%d" % (prefix, new_suffix) + + logging.info("Initial ping test, mcast: %s", mcast) + s, o = kvm_test_utils.ping(mcast, 10, interface=ifname, timeout=20) + if s != 0: + raise error.TestFail(" Ping return non-zero value %s" % o) + + logging.info("Flood ping test, mcast: %s", mcast) + kvm_test_utils.ping(mcast, None, interface=ifname, flood=True, + output_func=None, timeout=flood_minutes*60) + + logging.info("Final ping test, mcast: %s", mcast) + s, o = kvm_test_utils.ping(mcast, 10, interface=ifname, timeout=20) + if s != 0: + raise error.TestFail("Ping failed, status: %s, output: %s" % + (s, o)) + + finally: + logging.debug(session.get_command_output("ipmaddr show")) + session.get_command_output("kill -s SIGCONT %s" % pid) + session.close()client/tests/kvm/tests_base.cfg.sample +8
-1@@ -493,6 +493,13 @@ variants: type = nic_promisc file_size = 1, 1460, 65000, 100000000 + - multicast: install setup unattended_install.cdrom + type = multicast + nic_mode = tap + mcast = 225.0.0.1 + mgroup_count = 20 + flood_minutes = 1 + - physical_resources_check: install setup unattended_install.cdrom type = physical_resources_check catch_uuid_cmd = dmidecode | awk -F: '/UUID/ {print $2}'@@ -1267,7 +1274,7 @@ variants: # Windows section - @Windows: - no autotest linux_s3 vlan_tag ioquit unattended_install.(url|nfs|remote_ks) jumbo file_transfer nicdriver_unload nic_promisc + no autotest linux_s3 vlan_tag ioquit unattended_install.(url|nfs|remote_ks) jumbo file_transfer nicdriver_unload nic_promisc multicast shutdown_command = shutdown /s /f /t 0 reboot_command = shutdown /r /f /t 0 status_test_command = echo %errorlevel%Signature · 1 line
1.7.1
Re: [PATCH 11/18] KVM test: Add a subtest of multicast
Quoted 8 lines · Amos Kong
client/tests/kvm/tests/multicast.py line 42
Quoted 3 lines · Lucas Meneghel Rodrigues
From: Amos Kong <[email protected]>
client/tests/kvm/tests/multicast.py new file +2
-0+ # make sure guest replies to broadcasts + cmd_broadcast = "echo 0 > /proc/sys/net/ipv4/icmp_echo_ignore"Hello pradeep, thanks for your test, it's caused by this error
cmd_broadcast= "echo 0 >/proc/sys/net/ipv4/icmp_echo_ignore_broadcasts"
^ Ouch, I am dumb :( Amos, I've just fixed it, will publish an updated version of this patch, and remove it from the todo list. Thank you very much!
PATCH 12/18 KVM test: Add a subtest of pxe
In reply to Lucas Meneghel RodriguesFrom: Amos Kong <[email protected]>
This case just snoop tftp packet through tcpdump, it depends on public dhcp server, better to test it through dnsmasq.
FIXME: Use dnsmasq for pxe test
--- client/tests/kvm/tests/pxe.py | 31 +++++++++++++++++++++++++++++++ client/tests/kvm/tests_base.cfg.sample | 13 +++++++++++++ 2 files changed, 44 insertions(+), 0 deletions(-) create mode 100644 client/tests/kvm/tests/pxe.py
client/tests/kvm/tests/pxe.py new file +31 -0
@@ -0,0 +1,31 @@ +import logging +from autotest_lib.client.common_lib import error +import kvm_subprocess, kvm_test_utils + + +def run_pxe(test, params, env): + """ + PXE test: + + 1) Snoop the tftp packet in the tap device. + 2) Wait for some seconds. + 3) Check whether we could capture TFTP packets. + + @param test: KVM test object. + @param params: Dictionary with the test parameters. + @param env: Dictionary with test environment. + """ + vm = kvm_test_utils.get_living_vm(env, params.get("main_vm")) + timeout = int(params.get("pxe_timeout", 60)) + + logging.info("Try to boot from PXE") + status, output = kvm_subprocess.run_fg("tcpdump -nli %s" % vm.get_ifname(), + logging.debug, + "(pxe capture) ", + timeout) + + logging.info("Analyzing the tcpdump result...") + if not "tftp" in output: + raise error.TestFail("Couldn't find any TFTP packets after %s seconds" % + timeout) + logging.info("Found TFTP packet")
client/tests/kvm/tests_base.cfg.sample +13 -0
@@ -500,6 +500,19 @@ variants: mgroup_count = 20 flood_minutes = 1 + - pxe: + type = pxe + images = pxe + image_name_pxe = pxe-test + image_size_pxe = 1G + force_create_image_pxe = yes + remove_image_pxe = yes + extra_params += ' -boot n' + kill_vm_on_error = yes + network = bridge + restart_vm = yes + pxe_timeout = 60 + - physical_resources_check: install setup unattended_install.cdrom type = physical_resources_check catch_uuid_cmd = dmidecode | awk -F: '/UUID/ {print $2}'
Signature · 1 line
1.7.1
PATCH 13/18 KVM test: Add a subtest of changing MAC address
In reply to Lucas Meneghel RodriguesFrom: Amos Kong <[email protected]>
Test steps:
1. Get a new mac from pool, and the old mac addr of guest.
2. Execute the mac_change.sh in guest.
3. Relogin to guest and query the interfaces info by ifconfig
Changes from v3:
- Make sure the old and newly generated MAC addresses are different before proceeding with the test.
--- client/tests/kvm/tests/mac_change.py | 68 ++++++++++++++++++++++++++++++++ client/tests/kvm/tests_base.cfg.sample | 6 ++- 2 files changed, 73 insertions(+), 1 deletions(-) create mode 100644 client/tests/kvm/tests/mac_change.py
client/tests/kvm/tests/mac_change.py new file +68 -0
@@ -0,0 +1,68 @@ +import logging +from autotest_lib.client.common_lib import error +import kvm_utils, kvm_test_utils + + +def run_mac_change(test, params, env): + """ + Change MAC address of guest. + + 1) Get a new mac from pool, and the old mac addr of guest. + 2) Set new mac in guest and regain new IP. + 3) Re-log into guest with new MAC. + + @param test: KVM test object. + @param params: Dictionary with the test parameters. + @param env: Dictionary with test environment. + """ + timeout = int(params.get("login_timeout", 360)) + vm = kvm_test_utils.get_living_vm(env, params.get("main_vm")) + logging.info("Trying to log into guest '%s' by serial", vm.name) + session = kvm_utils.wait_for(lambda: vm.serial_login(), + timeout, 0, step=2) + if not session: + raise error.TestFail("Could not log into guest '%s'" % vm.name) + + old_mac = vm.get_mac_address(0) + new_different = False + while not new_different: + kvm_utils.free_mac_address(vm.root_dir, vm.instance, 0) + new_mac = kvm_utils.generate_mac_address(vm.root_dir, + vm.instance, + 0, vm.mac_prefix) + if old_mac != new_mac: + new_different = True + logging.info("The initial MAC address is %s", old_mac) + interface = kvm_test_utils.get_linux_ifname(session, old_mac) + # Start change MAC address + logging.info("Changing MAC address to %s", new_mac) + change_cmd = ("ifconfig %s down && ifconfig %s hw ether %s && " + "ifconfig %s up" % (interface, interface, new_mac, interface)) + if session.get_command_status(change_cmd) != 0: + raise error.TestFail("Fail to send mac_change command") + + # Verify whether MAC address was changed to the new one + logging.info("Verifying the new mac address") + if session.get_command_status("ifconfig | grep -i %s" % new_mac) != 0: + raise error.TestFail("Fail to change MAC address") + + # Restart `dhclient' to regain IP for new mac address + logging.info("Restart the network to gain new IP") + dhclient_cmd = "dhclient -r && dhclient %s" % interface + session.sendline(dhclient_cmd) + + # Re-log into the guest after changing mac address + if kvm_utils.wait_for(session.is_responsive, 120, 20, 3): + # Just warning when failed to see the session become dead, + # because there is a little chance the ip does not change. + logging.warn("The session is still responsive, settings may fail.") + session.close() + + # Re-log into guest and check if session is responsive + logging.info("Re-log into the guest") + session = kvm_test_utils.wait_for_login(vm, + timeout=int(params.get("login_timeout", 360))) + if not session.is_responsive(): + raise error.TestFail("The new session is not responsive.") + + session.close()
client/tests/kvm/tests_base.cfg.sample +5 -1
@@ -513,6 +513,10 @@ variants: restart_vm = yes pxe_timeout = 60 + - mac_change: install setup unattended_install.cdrom + type = mac_change + kill_vm = yes + - physical_resources_check: install setup unattended_install.cdrom type = physical_resources_check catch_uuid_cmd = dmidecode | awk -F: '/UUID/ {print $2}'
@@ -1287,7 +1291,7 @@ variants: # Windows section - @Windows: - no autotest linux_s3 vlan_tag ioquit unattended_install.(url|nfs|remote_ks) jumbo file_transfer nicdriver_unload nic_promisc multicast + no autotest linux_s3 vlan_tag ioquit unattended_install.(url|nfs|remote_ks) jumbo file_transfer nicdriver_unload nic_promisc multicast mac_change shutdown_command = shutdown /s /f /t 0 reboot_command = shutdown /r /f /t 0 status_test_command = echo %errorlevel%
Signature · 1 line
1.7.1
Re: [PATCH 13/18] KVM test: Add a subtest of changing MAC address
Quoted 9 lines · On Mon, 27 Sep 2010 18:43:59 -0400 Lucas Meneghel Rodrigues <[email protected]>…
From: Amos Kong <[email protected]>
Test steps:
1. Get a new mac from pool, and the old mac addr of guest.
2. Execute themac_change.shin guest.
3. Relogin to guest and query the interfaces info byifconfigChanges from v3:
After successful mac address change, why are we trying to kill the guest?
Please find the below logs..
3:26:13 DEBUG| 'kill_vm' specified; killing VM...
03:26:13 DEBUG| Destroying VM with PID 7420... 03:26:13 DEBUG| Trying to shutdown VM with shell command... 03:26:13 DEBUG| Trying to login with command 'ssh -o
UserKnownHostsFile=/dev/null -o PreferredAuthentications=password -p 22 [email protected]' 03:26:13 DEBUG| Got 'Are you sure...'; sending 'yes' 03:26:14 DEBUG| Got password prompt; sending '123456' 03:26:15 DEBUG| Got shell prompt -- logged in 03:26:15 DEBUG| Shutdown command sent; waiting for VM to go down... 03:26:16 DEBUG| (address cache) Adding cache entry: 9a:18:2d:12:78:aa ---> 10.168.0.8 03:26:16 DEBUG| (address cache) Adding cache entry: 9a:18:2d:12:78:aa ---> 10.168.0.8 03:26:33 DEBUG| (address cache) Adding cache entry: 02:18:0a:cc:7c:8c ---> 10.168.0.6 03:26:33 DEBUG| (address cache) Adding cache entry:
02:18:0a:cc:7c:8c ---> 10.168.0.6 03:26:38 DEBUG| (qemu) (Process terminated with status 0) 03:26:39 DEBUG| VM is down, freeing mac address. 03:26:39 DEBUG| Freeing MAC addr for NIC 20100929-231813-f5uA:0: 9a:18:2d:12:74:20 03:26:39 DEBUG| Terminating screendump thread...
PATCH 14/18 KVM test: Add a netperf subtest
In reply to Lucas Meneghel RodriguesFrom: Amos Kong <[email protected]>
Add network load by netperf, server is launched on guest, execute netperf client with different protocols on host. if all clients execute successfully, case will be pass. Test result will be record into result.txt.
Now this case only tests with "TCP_RR TCP_CRR UDP_RR TCP_STREAM TCP_MAERTS TCP_SENDFILE UDP_STREAM". DLPI only supported by Unix, unix domain test is not necessary, so drop test of DLPI and unix domain.
--- client/tests/kvm/tests/netperf.py | 56 ++++++++++++++++++++++++++++++++ client/tests/kvm/tests_base.cfg.sample | 10 ++++++ 2 files changed, 66 insertions(+), 0 deletions(-) create mode 100644 client/tests/kvm/tests/netperf.py
client/tests/kvm/tests/netperf.py new file +56 -0
@@ -0,0 +1,56 @@ +import logging, commands, os +from autotest_lib.client.common_lib import error +from autotest_lib.client.bin import utils +import kvm_test_utils + +def run_netperf(test, params, env): + """ + Network stress test with netperf. + + 1) Boot up a VM. + 2) Launch netserver on guest. + 3) Execute netperf client on host with different protocols. + 4) Output the test result. + + @param test: KVM test object. + @param params: Dictionary with the test parameters. + @param env: Dictionary with test environment. + """ + vm = kvm_test_utils.get_living_vm(env, params.get("main_vm")) + session = kvm_test_utils.wait_for_login(vm, + timeout=int(params.get("login_timeout", 360))) + netperf_dir = os.path.join(os.environ['AUTODIR'], "tests/netperf2") + setup_cmd = params.get("setup_cmd") + guest_ip = vm.get_address() + result_file = os.path.join(test.resultsdir, "output_%s" % test.iteration) + + session.get_command_output("iptables -F") + for i in params.get("netperf_files").split(): + if not vm.copy_files_to(os.path.join(netperf_dir, i), "/tmp"): + raise error.TestError("Could not copy files to guest") + if session.get_command_status(setup_cmd % "/tmp", timeout=200) != 0: + raise error.TestFail("Fail to setup netperf on guest") + if session.get_command_status(params.get("netserver_cmd") % "/tmp") != 0: + raise error.TestFail("Fail to start netperf server on guest") + + try: + logging.info("Setup and run netperf client on host") + utils.run(setup_cmd % netperf_dir) + success = True + file(result_file, "w").write("Netperf Test Result\n") + for i in params.get("protocols").split(): + cmd = params.get("netperf_cmd") % (netperf_dir, i, guest_ip) + logging.debug("Execute netperf client test: %s", cmd) + s, o = commands.getstatusoutput(cmd) + if s != 0: + logging.error("Fail to execute netperf test, protocol:%s", i) + success = False + else: + logging.info(o) + file(result_file, "a+").write("%s\n" % o) + if not success: + raise error.TestFail("Some of the netperf tests failed") + + finally: + session.get_command_output("killall netserver") + session.close()
client/tests/kvm/tests_base.cfg.sample +10 -0
@@ -517,6 +517,16 @@ variants: type = mac_change kill_vm = yes + - netperf: install setup unattended_install.cdrom + type = netperf + nic_mode = tap + netperf_files = netperf-2.4.5.tar.bz2 wait_before_data.patch + setup_cmd = "cd %s && tar xvfj netperf-2.4.5.tar.bz2 && cd netperf-2.4.5 && patch -p0 < ../wait_before_data.patch && ./configure && make" + netserver_cmd = %s/netperf-2.4.5/src/netserver + # test time is 60 seconds, set the buffer size to 1 for more hardware interrupt + netperf_cmd = %s/netperf-2.4.5/src/netperf -t %s -H %s -l 60 -- -m 1 + protocols = "TCP_STREAM TCP_MAERTS TCP_RR TCP_CRR UDP_RR TCP_SENDFILE UDP_STREAM" + - physical_resources_check: install setup unattended_install.cdrom type = physical_resources_check catch_uuid_cmd = dmidecode | awk -F: '/UUID/ {print $2}'
Signature · 1 line
1.7.1
Re: [PATCH 14/18] KVM test: Add a netperf subtest
In Todo list i find TCP_CRR UDP_RR test case failures.
2) netperf
17:35:11 DEBUG| Execute netperf client
test: /root/autotest/client/tests/netperf2/netperf-2.4.5/src/netperf -tTCP_CRR -H 10.16.74.142 -l 60 -- -m 1 17:35:45 ERROR| Fail to execute
netperf test, protocol:TCP_CRR 17:35:45 DEBUG| Execute netperf client
test: /root/autotest/client/tests/netperf2/netperf-2.4.5/src/netperf -t UDP_RR -H 10.16.74.142 -l 60 -- -m 1 17:36:06 ERROR| Fail to execute netperf test, protocol:UDP_RR
I havent noticed any issues with UDP_RR
But with RHEL 5.5 guest TCP_CRR fails. with other RHEL latest distro it works fine. Need to figure out if its test issue or RHEL 5.5 issue.
Re: [PATCH 14/18] KVM test: Add a netperf subtest
Quoted 15 lines · pradeep
In Todo list i find
TCP_CRRUDP_RRtest case failures.2) netperf
17:35:11 DEBUG| Execute netperf client
test:/root/autotest/client/tests/netperf2/netperf-2.4.5/src/netperf-tTCP_CRR-H 10.16.74.142 -l 60 -- -m 1 17:35:45 ERROR| Fail to execute
netperf test, protocol:TCP_CRR 17:35:45 DEBUG| Execute netperf client
test:/root/autotest/client/tests/netperf2/netperf-2.4.5/src/netperf-tUDP_RR-H 10.16.74.142 -l 60 -- -m 1 17:36:06 ERROR| Fail to execute netperf test, protocol:UDP_RR
Quoted 3 lines
I havent noticed any issues with
UDP_RR
But with RHEL 5.5 guestTCP_CRRfails. with other RHEL latest distro it works fine. Need to figure out if its test issue or RHEL 5.5 issue.
This case can pass with rhel5.5 & rhel6.0, not test with fedora. it would not be the problem of testcase.
I did not touch this problem, can you provide more debug info ? eg, tcpdump, ...
Quoted 4 lines
--
To unsubscribe from this list: send the line "unsubscribe kvm" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [PATCH 14/18] KVM test: Add a netperf subtest
Quoted 9 lines
This case can pass with rhel5.5 & rhel6.0, not test with fedora. it would not be the problem of testcase.
I did not touch this problem, can you provide more debug info ? eg, tcpdump, ...
It seems like RHEL 5.5 issue
it fails only with TCP_CRR
PATCH 15/18 KVM test: kvm_utils - Add support of check if remote port free
In reply to Lucas Meneghel RodriguesFrom: Amos Kong <[email protected]>
--- client/tests/kvm/kvm_utils.py | 23 +++++++++++++++-------- 1 files changed, 15 insertions(+), 8 deletions(-)
client/tests/kvm/kvm_utils.py +15 -8
@@ -831,7 +831,7 @@ def scp_from_remote(host, port, username, password, remote_path, local_path, # The following are utility functions related to ports. -def is_port_free(port): +def is_port_free(port, address): """ Return True if the given port is available for use.
@@ -840,15 +840,22 @@ def is_port_free(port): try: s = socket.socket() #s.setsockopt(socket.SOL_SOCKET, socket.SO_REUSEADDR, 1) - s.bind(("localhost", port)) - free = True + if address == "localhost": + s.bind(("localhost", port)) + free = True + else: + s.connect((address, port)) + free = False except socket.error: - free = False + if address == "localhost": + free = False + else: + free = True s.close() return free -def find_free_port(start_port, end_port): +def find_free_port(start_port, end_port, address="localhost"): """ Return a host free port in the range [start_port, end_port].
@@ -856,12 +863,12 @@ def find_free_port(start_port, end_port): @param end_port: Port immediately after the last one that will be checked. """ for i in range(start_port, end_port): - if is_port_free(i): + if is_port_free(i, address): return i return None -def find_free_ports(start_port, end_port, count): +def find_free_ports(start_port, end_port, count, address="localhost"): """ Return count of host free ports in the range [start_port, end_port].
@@ -872,7 +879,7 @@ def find_free_ports(start_port, end_port, count): ports = [] i = start_port while i < end_port and count > 0: - if is_port_free(i): + if is_port_free(i, address): ports.append(i) count -= 1 i += 1
Signature · 1 line
1.7.1
PATCH 16/18 KVM test: Improve vlan subtest
In reply to Lucas Meneghel RodriguesFrom: Amos Kong <[email protected]>
This is an enhancement of existed vlan test. Rename the vlan_tag.py to vlan.py, it is more reasonable.
. Setup arp from "/proc/sys/net/ipv4/conf/all/arp_ignore"
. Multiple vlans exist simultaneously
. Test ping between same and different vlans
. Test by TCP data transfer, floop ping between same vlan
. Maximal plumb/unplumb vlans
--- client/tests/kvm/tests/vlan.py | 186 ++++++++++++++++++++++++++++++++ client/tests/kvm/tests/vlan_tag.py | 68 ------------ client/tests/kvm/tests_base.cfg.sample | 16 ++- 3 files changed, 196 insertions(+), 74 deletions(-) create mode 100644 client/tests/kvm/tests/vlan.py delete mode 100644 client/tests/kvm/tests/vlan_tag.py
client/tests/kvm/tests/vlan.py new file +186 -0
@@ -0,0 +1,186 @@ +import logging, time, re +from autotest_lib.client.common_lib import error +import kvm_test_utils, kvm_utils + +def run_vlan(test, params, env): + """ + Test 802.1Q vlan of NIC, config it by vconfig command. + + 1) Create two VMs. + 2) Setup guests in 10 different vlans by vconfig and using hard-coded + ip address. + 3) Test by ping between same and different vlans of two VMs. + 4) Test by TCP data transfer, floop ping between same vlan of two VMs. + 5) Test maximal plumb/unplumb vlans. + 6) Recover the vlan config. + + @param test: KVM test object. + @param params: Dictionary with the test parameters. + @param env: Dictionary with test environment. + """ + + vm = [] + session = [] + vm_ip = [] + digest_origin = [] + vlan_ip = ['', ''] + ip_unit = ['1', '2'] + subnet = params.get("subnet") + vlan_num = int(params.get("vlan_num")) + maximal = int(params.get("maximal")) + file_size = params.get("file_size") + + vm.append(kvm_test_utils.get_living_vm(env, params.get("main_vm"))) + vm.append(kvm_test_utils.get_living_vm(env, "vm2")) + + def add_vlan(session, id, iface="eth0"): + if session.get_command_status("vconfig add %s %s" % (iface, id)) != 0: + raise error.TestError("Fail to add %s.%s" % (iface, id)) + + + def set_ip_vlan(session, id, ip, iface="eth0"): + iface = "%s.%s" % (iface, id) + if session.get_command_status("ifconfig %s %s" % (iface, ip)) != 0: + raise error.TestError("Fail to configure ip for %s" % iface) + + + def set_arp_ignore(session, iface="eth0"): + ignore_cmd = "echo 1 > /proc/sys/net/ipv4/conf/all/arp_ignore" + if session.get_command_status(ignore_cmd) != 0: + raise error.TestError("Fail to set arp_ignore of %s" % session) + + + def rem_vlan(session, id, iface="eth0"): + rem_vlan_cmd = "if [[ -e /proc/net/vlan/%s ]];then vconfig rem %s;fi" + iface = "%s.%s" % (iface, id) + s = session.get_command_status(rem_vlan_cmd % (iface, iface)) + return s + + + def nc_transfer(src, dst): + nc_port = kvm_utils.find_free_port(1025, 5334, vm_ip[dst]) + listen_cmd = params.get("listen_cmd") + send_cmd = params.get("send_cmd") + + #listen in dst + listen_cmd = listen_cmd % (nc_port, "receive") + session[dst].sendline(listen_cmd) + time.sleep(2) + #send file from src to dst + send_cmd = send_cmd % (vlan_ip[dst], str(nc_port), "file") + if session[src].get_command_status(send_cmd, timeout = 60) != 0: + raise error.TestFail ("Fail to send file" + " from vm%s to vm%s" % (src+1, dst+1)) + s, o = session[dst].read_up_to_prompt(timeout=60) + if s != True: + raise error.TestFail ("Fail to receive file" + " from vm%s to vm%s" % (src+1, dst+1)) + #check MD5 message digest of receive file in dst + output = session[dst].get_command_output("md5sum receive").strip() + digest_receive = re.findall(r'(\w+)', output)[0] + if digest_receive == digest_origin[src]: + logging.info("file succeed received in vm %s" % vlan_ip[dst]) + else: + logging.info("digest_origin is %s" % digest_origin[src]) + logging.info("digest_receive is %s" % digest_receive) + raise error.TestFail("File transfered differ from origin") + session[dst].get_command_status("rm -f receive") + + + for i in range(2): + session.append(kvm_test_utils.wait_for_login(vm[i], + timeout=int(params.get("login_timeout", 360)))) + if not session[i] : + raise error.TestError("Could not log into guest(vm%d)" % i) + logging.info("Logged in") + + #get guest ip + vm_ip.append(vm[i].get_address()) + + #produce sized file in vm + dd_cmd = "dd if=/dev/urandom of=file bs=1024k count=%s" + if session[i].get_command_status(dd_cmd % file_size) != 0: + raise error.TestFail("File producing failed") + #record MD5 message digest of file + s, output =session[i].get_command_status_output("md5sum file", + timeout=60) + if s != 0: + raise error.TestFail("File MD5_checking failed" ) + digest_origin.append(re.findall(r'(\w+)', output)[0]) + + #stop firewall in vm + session[i].get_command_status("/etc/init.d/iptables stop") + + #load 8021q module for vconfig + load_8021q_cmd = "modprobe 8021q" + if session[i].get_command_status(load_8021q_cmd) != 0: + raise error.TestError("Fail to load 8021q module on VM%s" % i) + + try: + for i in range(2): + for vlan_i in range(1, vlan_num+1): + add_vlan(session[i], vlan_i) + set_ip_vlan(session[i], vlan_i, "%s.%s.%s" % \ + (subnet, vlan_i, ip_unit[i])) + set_arp_ignore(session[i]) + + for vlan in range(1, vlan_num+1): + logging.info("Test for vlan %s" % vlan) + + logging.info("Ping between vlans") + interface = 'eth0.' + str(vlan) + for vlan2 in range(1, vlan_num+1): + for i in range(2): + dest = subnet +'.'+ str(vlan2)+ '.' + ip_unit[(i+1)%2] + s, o = kvm_test_utils.ping(dest, count=2, + interface=interface, + session=session[i], timeout=30) + if ((vlan == vlan2) ^ (s == 0)): + raise error.TestFail ("%s ping %s unexpected" % + (interface, dest)) + + vlan_ip[0] = subnet + '.' + str(vlan) + '.' + ip_unit[0] + vlan_ip[1] = subnet + '.' + str(vlan) + '.' + ip_unit[1] + + logging.info("Flood ping") + def flood_ping(src, dst): + # we must use a dedicated session becuase the kvm_subprocess + # does not have the other method to interrupt the process in + # the guest rather than close the session. + session_flood = kvm_test_utils.wait_for_login(vm[src], + timeout = 60) + kvm_test_utils.ping(vlan_ip[dst], flood=True, + interface=interface, + session=session_flood, timeout=10) + session_flood.close() + + flood_ping(0,1) + flood_ping(1,0) + + logging.info("Transfering data through nc") + nc_transfer(0, 1) + nc_transfer(1, 0) + + finally: + for vlan in range(1, vlan_num+1): + rem_vlan(session[0], vlan) + rem_vlan(session[1], vlan) + logging.info("rem eth0.%s" % vlan) + + # Plumb/unplumb maximal unber of vlan interfaces + i = 1 + s = 0 + try: + logging.info("Testing the plumb of vlan interface") + for i in range (1, maximal+1): + add_vlan(session[0], i) + finally: + for j in range (1, i+1): + s = s or rem_vlan(session[0], j) + if s == 0: + logging.info("maximal interface plumb test done") + else: + logging.error("maximal interface plumb test failed") + + session[0].close() + session[1].close()
client/tests/kvm/tests/vlan_tag.py deleted +0 -68
68 lines not on this page · raw message
client/tests/kvm/tests_base.cfg.sample +10 -6
@@ -456,17 +456,21 @@ variants: - fmt_raw: image_format_stg = raw - - vlan_tag: install setup unattended_install.cdrom - type = vlan_tag + - vlan: install setup unattended_install.cdrom + type = vlan # subnet should not be used by host - subnet = 192.168.123 - vlans = "10 20" + subnet = "192.168" + vlan_num = 5 + file_size = 10 + maximal = 4094 + listen_cmd = "nc -l %s > %s" + send_cmd = "nc %s %s < %s" nic_mode = tap vms += " vm2" extra_params_vm1 += " -snapshot" extra_params_vm2 += " -snapshot" + kill_vm_vm2 = yes kill_vm_gracefully_vm2 = no - address_index_vm2 = 1 - ping: install setup unattended_install.cdrom type = ping
@@ -1301,7 +1305,7 @@ variants: # Windows section - @Windows: - no autotest linux_s3 vlan_tag ioquit unattended_install.(url|nfs|remote_ks) jumbo file_transfer nicdriver_unload nic_promisc multicast mac_change + no autotest linux_s3 vlan ioquit unattended_install.(url|nfs|remote_ks) jumbo file_transfer nicdriver_unload nic_promisc multicast mac_change shutdown_command = shutdown /s /f /t 0 reboot_command = shutdown /r /f /t 0 status_test_command = echo %errorlevel%
Signature · 1 line
1.7.1
Re: [PATCH 16/18] KVM test: Improve vlan subtest
Quoted 18 lines · On Mon, 27 Sep 2010 18:44:02 -0400 Lucas Meneghel Rodrigues <[email protected]>…
From: Amos Kong <[email protected]>
This is an enhancement of existed vlan test. Rename the
vlan_tag.pytovlan.py, it is more reasonable.
. Setup arp from "/proc/sys/net/ipv4/conf/all/arp_ignore" . Multiple vlans exist simultaneously
. Test ping between same and different vlans
. Test by TCP data transfer, floop ping between same vlan . Maximal plumb/unplumb vlans(quoted diff) +2
-0+ + vm.append(kvm_test_utils.get_living_vm(env,
params.get("main_vm")))client/tests/kvm/tests/vlan.py new file +4
-0+ vm.append(kvm_test_utils.get_living_vm(env, "vm2")) + + def add_vlan(session, id, iface="eth0"): + if session.get_command_status("vconfig add %s %s" % (iface,
Quoted 2 lines
id)) != 0:
+ raiseerror.TestError("Fail to add %s.%s" % (iface, id))
HI Lucas
I got below error with my guests.
With (2.6.32-71 kernel) guest
21:17:23 DEBUG| Sending command: vconfig add eth0 1
21:17:23 DEBUG| Command failed; status: 3, output: ERROR: trying to add VLAN #1 to IF -:eth0:- error: No such device
21:17:25 ERROR| Test failed: TestError: Fail to add eth0.1
client/tests/kvm/tests_base.cfg.sample variants: · line 462
Quoted 3 lines
client/tests/kvm/tests_base.cfg.sample +1
-2- subnet = 192.168.123 - vlans = "10 20" + subnet = "192.168"
My guest has got DHCP ip as 10.168*.
With RHEL 5.5 guest
02:30:39 DEBUG| PING 192.168.1.2 (192.168.1.2) from 192.168.1.1 eth0.1:
56(84) bytes of data. 02:30:42 DEBUG| From 192.168.1.1 icmp_seq=1 Destination Host Unreachable 02:30:42 DEBUG| From 192.168.1.1 icmp_seq=2 Destination Host Unreachable
02:30:45 INFO | rem eth0.5
02:30:45 ERROR| Test failed: TestFail: eth0.1 ping 192.168.1.2 unexpected 02:30:45 DEBUG| Postprocessing VM 'vm1'...
Re: [PATCH 16/18] KVM test: Improve vlan subtest
Quoted 25 lines · pradeep
Quoted 18 lines · On Mon, 27 Sep 2010 18:44:02 -0400 Lucas Meneghel Rodrigues <[email protected]>…
From: Amos Kong <[email protected]>
This is an enhancement of existed vlan test. Rename the
vlan_tag.pytovlan.py, it is more reasonable.
. Setup arp from "/proc/sys/net/ipv4/conf/all/arp_ignore" . Multiple vlans exist simultaneously
. Test ping between same and different vlans
. Test by TCP data transfer, floop ping between same vlan . Maximal plumb/unplumb vlans(quoted diff) +2
-0+ + vm.append(kvm_test_utils.get_living_vm(env,
params.get("main_vm")))client/tests/kvm/tests/vlan.py new file +4
-0+ vm.append(kvm_test_utils.get_living_vm(env, "vm2")) + + def add_vlan(session, id, iface="eth0"): + if session.get_command_status("vconfig add %s %s" % (iface,Quoted 2 lines
id)) != 0:
+ raiseerror.TestError("Fail to add %s.%s" % (iface, id))HI Lucas
Quoted 7 lines
I got below error with my guests.
With (2.6.32-71 kernel) guest
21:17:23 DEBUG| Sending command: vconfig add eth0 1
21:17:23 DEBUG| Command failed; status: 3, output: ERROR: trying to add VLAN #1 to IF -:eth0:- error: No such device
it was caused by the hardcode interface name.
lucas, attached the latest vlan.py. try to get right ifname by kvm_test_utils.get_linux_ifname()
import logging, time, re
from autotest_lib.client.common_lib import error
import kvm_test_utils, kvm_utils
def run_vlan(test, params, env):
"""
Test 802.1Q vlan of NIC, config it by vconfig command.
1) Create two VMs.
2) Setup guests in 10 different vlans by vconfig and using hard-coded ip address.
3) Test by ping between same and different vlans of two VMs.
4) Test by TCP data transfer, floop ping between same vlan of two VMs.
5) Test maximal plumb/unplumb vlans.
6) Recover the vlan config.
@param test: KVM test object.
@param params: Dictionary with the test parameters. @param env: Dictionary with test environment. """
vm = []
session = []
ifname = []
vm_ip = []
digest_origin = []
vlan_ip = ['', '']
ip_unit = ['1', '2']
subnet = params.get("subnet")
vlan_num = int(params.get("vlan_num"))
maximal = int(params.get("maximal"))
file_size = params.get("file_size")
vm.append(kvm_test_utils.get_living_vm(env, params.get("main_vm"))) vm.append(kvm_test_utils.get_living_vm(env, "vm2"))
def add_vlan(session, id, iface="eth0"):
if session.get_command_status("vconfig add %s %s" % (iface, id)) != 0:
raise error.TestError("Fail to add %s.%s" % (iface, id))
def set_ip_vlan(session, id, ip, iface="eth0"):
iface = "%s.%s" % (iface, id)
if session.get_command_status("ifconfig %s %s" % (iface, ip)) != 0:
raise error.TestError("Fail to configure ip for %s" % iface)
def set_arp_ignore(session, iface="eth0"):
ignore_cmd = "echo 1 > /proc/sys/net/ipv4/conf/all/arp_ignore" if session.get_command_status(ignore_cmd) != 0:
raise error.TestError("Fail to set arp_ignore of %s" % session)
def rem_vlan(session, id, iface="eth0"):
rem_vlan_cmd = "if [[ -e /proc/net/vlan/%s ]];then vconfig rem %s;fi" iface = "%s.%s" % (iface, id)
s = session.get_command_status(rem_vlan_cmd % (iface, iface)) return s
def nc_transfer(src, dst):
nc_port = kvm_utils.find_free_port(1025, 5334, vm_ip[dst]) listen_cmd = params.get("listen_cmd")
send_cmd = params.get("send_cmd")
#listen in dst
listen_cmd = listen_cmd % (nc_port, "receive") session[dst].sendline(listen_cmd)
time.sleep(2)
#send file from src to dst
send_cmd = send_cmd % (vlan_ip[dst], str(nc_port), "file") if session[src].get_command_status(send_cmd, timeout = 60) != 0:
raise error.TestFail ("Fail to send file"
" from vm%s to vm%s" % (src+1, dst+1))
s, o = session[dst].read_up_to_prompt(timeout=60)
if s != True:
raise error.TestFail ("Fail to receive file"
" from vm%s to vm%s" % (src+1, dst+1))
#check MD5 message digest of receive file in dst output = session[dst].get_command_output("md5sum receive").strip() digest_receive = re.findall(r'(\w+)', output)[0]
if digest_receive == digest_origin[src]:
logging.info("file succeed received in vm %s" % vlan_ip[dst])
else:
logging.info("digest_origin is %s" % digest_origin[src]) logging.info("digest_receive is %s" % digest_receive) raise error.TestFail("File transfered differ from origin")
session[dst].get_command_status("rm -f receive")
for i in range(2):
session.append(kvm_test_utils.wait_for_login(vm[i],
timeout=int(params.get("login_timeout", 360))))
if not session[i] :
raise error.TestError("Could not log into guest(vm%d)" % i)
logging.info("Logged in")
ifname.append(kvm_test_utils.get_linux_ifname(session[i],
vm[i].get_mac_address()))
#get guest ip
vm_ip.append(vm[i].get_address())
#produce sized file in vm
dd_cmd = "dd if=/dev/urandom of=file bs=1024k count=%s" if session[i].get_command_status(dd_cmd % file_size) != 0:
raise error.TestFail("File producing failed")
#record MD5 message digest of file
s, output =session[i].get_command_status_output("md5sum file",
timeout=60)
if s != 0:
raise error.TestFail("File MD5_checking failed" )
digest_origin.append(re.findall(r'(\w+)', output)[0])
#stop firewall in vm session[i].get_command_status("/etc/init.d/iptables stop")
#load 8021q module for vconfig
load_8021q_cmd = "modprobe 8021q"
if session[i].get_command_status(load_8021q_cmd) != 0:
raise error.TestError("Fail to load 8021q module on VM%s" % i)
try:
for i in range(2):
for vlan_i in range(1, vlan_num+1):
add_vlan(session[i], vlan_i, ifname[i]) set_ip_vlan(session[i], vlan_i, "%s.%s.%s" %
(subnet, vlan_i, ip_unit[i]), ifname[i])
set_arp_ignore(session[i], ifname[i])
for vlan in range(1, vlan_num+1):
logging.info("Test for vlan %s" % vlan)
logging.info("Ping between vlans")
interface = ifname[0] + '.' + str(vlan)
for vlan2 in range(1, vlan_num+1):
for i in range(2):
interface = ifname[i] + '.' + str(vlan)
dest = subnet +'.'+ str(vlan2)+ '.' + ip_unit[(i+1)%2] s, o = kvm_test_utils.ping(dest, count=2,
interface=interface, session=session[i], timeout=30)
if ((vlan == vlan2) ^ (s == 0)):
raise error.TestFail ("%s ping %s unexpected" %
(interface, dest))
vlan_ip[0] = subnet + '.' + str(vlan) + '.' + ip_unit[0] vlan_ip[1] = subnet + '.' + str(vlan) + '.' + ip_unit[1]
logging.info("Flood ping")
def flood_ping(src, dst):
# we must use a dedicated session becuase the kvm_subprocess # does not have the other method to interrupt the process in # the guest rather than close the session. session_flood = kvm_test_utils.wait_for_login(vm[src],
timeout = 60)
kvm_test_utils.ping(vlan_ip[dst], flood=True,
interface=ifname[src], session=session_flood, timeout=10)
session_flood.close()
flood_ping(0,1)
flood_ping(1,0)
logging.info("Transfering data through nc") nc_transfer(0, 1)
nc_transfer(1, 0)
finally:
for vlan in range(1, vlan_num+1):
rem_vlan(session[0], vlan, ifname[0])
rem_vlan(session[1], vlan, ifname[1])
logging.info("rem vlan: %s" % vlan)
# Plumb/unplumb maximal unber of vlan interfaces
i = 1
s = 0
try:
logging.info("Testing the plumb of vlan interface") for i in range (1, maximal+1):
add_vlan(session[0], i, ifname[0])
finally:
for j in range (1, i+1):
s = s or rem_vlan(session[0], j, ifname[0])
if s == 0:
logging.info("maximal interface plumb test done")
else:
logging.error("maximal interface plumb test failed")
session[0].close()
session[1].close()
_______________________________________________
Autotest mailing list
[email protected]
http://test.kernel.org/cgi-bin/mailman/listinfo/autotest
PATCH 17/18 KVM test: vlan subtest - Replace extra_params '-snapshot' with image_snapshot
In reply to Lucas Meneghel RodriguesFrom: Amos Kong <[email protected]>
Framework could not totalise default extra_params and extra_params_vm1 in the following condition, it's difficult to realise when parsing config file or calling get_sub_dict*().
extra_params += ' str1'
- case:extra_params_vm1 += " str2"
--- client/tests/kvm/tests_base.cfg.sample | 3 +-- 1 files changed, 1 insertions(+), 2 deletions(-)
client/tests/kvm/tests_base.cfg.sample +1 -2
@@ -467,8 +467,7 @@ variants: send_cmd = "nc %s %s < %s" nic_mode = tap vms += " vm2" - extra_params_vm1 += " -snapshot" - extra_params_vm2 += " -snapshot" + image_snapshot = yes kill_vm_vm2 = yes kill_vm_gracefully_vm2 = no
Signature · 1 line
1.7.1
PATCH 18/18 KVM test: Add subtest of testing offload by ethtool
In reply to Lucas Meneghel RodriguesThe latest case contains TX/RX/SG/TSO/GSO/GRO/LRO test. RTL8139 NIC doesn't support TSO, LRO, it's too old, so drop offload test from rtl8139. LRO, GRO are only supported by latest kernel, virtio nic doesn't support receive offloading function.
Initialize the callbacks first and execute all the sub tests one by one, all the result will be check at the end. When execute this test, vhost should be enabled, then most of new features can be used. Vhost doesn't support VIRTIO_NET_F_MRG_RXBUF, so do not check large packets in received offload test.
Transfer files by scp between host and guest, match new opened TCP port by netstat. Capture the packages info by tcpdump, it contains package length.
Changes from v3:
- Error the test on the very beginning if we can't find ethtool installed on guest.
TODO: Query supported offload function by 'ethtool'
TODO: Find a clean way to get ethtool installed through apt-get/yum/whatever
--- client/tests/kvm/tests/ethtool.py | 222 ++++++++++++++++++++++++++++++++ client/tests/kvm/tests_base.cfg.sample | 13 ++- 2 files changed, 233 insertions(+), 2 deletions(-) create mode 100644 client/tests/kvm/tests/ethtool.py
client/tests/kvm/tests/ethtool.py new file +222 -0
@@ -0,0 +1,222 @@ +import logging, commands, re +from autotest_lib.client.common_lib import error +from autotest_lib.client.bin import utils +import kvm_test_utils, kvm_utils + +def run_ethtool(test, params, env): + """ + Test offload functions of ethernet device by ethtool + + 1) Log into a guest. + 2) Initialize the callback of sub functions. + 3) Enable/disable sub function of NIC. + 4) Execute callback function. + 5) Check the return value. + 6) Restore original configuration. + + @param test: KVM test object. + @param params: Dictionary with the test parameters. + @param env: Dictionary with test environment. + + @todo: Not all guests have ethtool installed, so + find a way to get it installed using yum/apt-get/ + whatever + """ + def ethtool_get(type): + feature_pattern = { + 'tx': 'tx.*checksumming', + 'rx': 'rx.*checksumming', + 'sg': 'scatter.*gather', + 'tso': 'tcp.*segmentation.*offload', + 'gso': 'generic.*segmentation.*offload', + 'gro': 'generic.*receive.*offload', + 'lro': 'large.*receive.*offload', + } + s, o = session.get_command_status_output("ethtool -k %s" % ethname) + try: + return re.findall("%s: (.*)" % feature_pattern.get(type), o)[0] + except IndexError: + logging.debug("Could not get %s status" % type) + + + def ethtool_set(type, status): + """ + Set ethernet device offload status + + @param type: Offload type name + @param status: New status will be changed to + """ + logging.info("Try to set %s %s" % (type, status)) + if status not in ["off", "on"]: + return False + cmd = "ethtool -K %s %s %s" % (ethname, type, status) + if ethtool_get(type) != status: + return session.get_command_status(cmd) == 0 + if ethtool_get(type) != status: + logging.error("Fail to set %s %s" % (type, status)) + return False + return True + + + def ethtool_save_params(): + logging.info("Save ethtool configuration") + for i in supported_features: + feature_status[i] = ethtool_get(i) + + + def ethtool_restore_params(): + logging.info("Restore ethtool configuration") + for i in supported_features: + ethtool_set(i, feature_status[i]) + + + def compare_md5sum(name): + logging.info("Compare md5sum of the files on guest and host") + host_result = utils.hash_file(name, method="md5") + try: + o = session.get_command_output("md5sum %s" % name) + guest_result = re.findall("\w+", o)[0] + except IndexError: + logging.error("Could not get file md5sum in guest") + return False + logging.debug("md5sum: guest(%s), host(%s)" % + (guest_result, host_result)) + return guest_result == host_result + + + def transfer_file(src="guest"): + """ + Transfer file by scp, use tcpdump to capture packets, then check the + return string. + + @param src: Source host of transfer file + @return: Tuple (status, error msg/tcpdump result) + """ + session2.get_command_status("rm -rf %s" % filename) + dd_cmd = "dd if=/dev/urandom of=%s bs=1M count=%s" % (filename, + params.get("filesize")) + logging.info("Creat file in source host, cmd: %s" % dd_cmd) + tcpdump_cmd = "tcpdump -lep -s 0 tcp -vv port ssh" + if src == "guest": + s = session.get_command_status(dd_cmd, timeout=360) + tcpdump_cmd += " and src %s" % guest_ip + copy_files_fun = vm.copy_files_from + else: + s, o = commands.getstatusoutput(dd_cmd) + tcpdump_cmd += " and dst %s" % guest_ip + copy_files_fun = vm.copy_files_to + if s != 0: + return (False, "Fail to create file by dd, cmd: %s" % dd_cmd) + + # only capture the new tcp port after offload setup + original_tcp_ports = re.findall("tcp.*:(\d+).*%s" % guest_ip, + utils.system_output("/bin/netstat -nap")) + for i in original_tcp_ports: + tcpdump_cmd += " and not port %s" % i + logging.debug("Listen by command: %s" % tcpdump_cmd) + session2.sendline(tcpdump_cmd) + if not kvm_utils.wait_for(lambda: session.get_command_status( + "pgrep tcpdump") == 0, 30): + return (False, "Tcpdump process wasn't launched") + + logging.info("Start to transfer file") + if not copy_files_fun(filename, filename): + return (False, "Child process transfer file failed") + logging.info("Transfer file completed") + if session.get_command_status("killall tcpdump") != 0: + return (False, "Could not kill all tcpdump process") + s, tcpdump_string = session2.read_up_to_prompt(timeout=60) + if not s: + return (False, "Fail to read tcpdump's output") + + if not compare_md5sum(filename): + return (False, "Files' md5sum mismatched") + return (True, tcpdump_string) + + + def tx_callback(status="on"): + s, o = transfer_file(src="guest") + if not s: + logging.error(o) + return False + return True + + + def rx_callback(status="on"): + s, o = transfer_file(src="host") + if not s: + logging.error(o) + return False + return True + + + def so_callback(status="on"): + s, o = transfer_file(src="guest") + if not s: + logging.error(o) + return False + logging.info("Check if contained large frame") + # MTU: default IPv4 MTU is 1500 Bytes, ethernet header is 14 Bytes + return (status == "on") ^ (len([i for i in re.findall( + "length (\d*):", o) if int(i) > mtu]) == 0) + + + def ro_callback(status="on"): + s, o = transfer_file(src="host") + if not s: + logging.error(o) + return False + return True + + + vm = kvm_test_utils.get_living_vm(env, params.get("main_vm")) + session = kvm_test_utils.wait_for_login(vm, + timeout=int(params.get("login_timeout", 360))) + # Let's just error the test if we identify that there's no ethtool installed + if session.get_command_status("ethtool -h"): + raise error.TestError("Command ethtool not installed on guest") + session2 = kvm_test_utils.wait_for_login(vm, + timeout=int(params.get("login_timeout", 360))) + mtu = 1514 + feature_status = {} + filename = "/tmp/ethtool.dd" + guest_ip = vm.get_address() + ethname = kvm_test_utils.get_linux_ifname(session, vm.get_mac_address(0)) + supported_features = params.get("supported_features").split() + test_matrix = { + # type:(callback, (dependence), (exclude) + "tx": (tx_callback, (), ()), + "rx": (rx_callback, (), ()), + "sg": (tx_callback, ("tx",), ()), + "tso": (so_callback, ("tx", "sg",), ("gso",)), + "gso": (so_callback, (), ("tso",)), + "gro": (ro_callback, ("rx",), ("lro",)), + "lro": (rx_callback, (), ("gro",)), + } + ethtool_save_params() + success = True + try: + for type in supported_features: + callback = test_matrix[type][0] + for i in test_matrix[type][2]: + if not ethtool_set(i, "off"): + logging.error("Fail to disable %s" % i) + success = False + for i in [f for f in test_matrix[type][1]] + [type]: + if not ethtool_set(i, "on"): + logging.error("Fail to enable %s" % i) + success = False + if not callback(): + raise error.TestFail("Test failed, %s: on" % type) + + if not ethtool_set(type, "off"): + logging.error("Fail to disable %s" % type) + success = False + if not callback(status="off"): + raise error.TestFail("Test failed, %s: off" % type) + if not success: + raise error.TestError("Enable/disable offload function fail") + finally: + ethtool_restore_params() + session.close() + session2.close()
client/tests/kvm/tests_base.cfg.sample +11 -2
@@ -530,6 +530,11 @@ variants: netperf_cmd = %s/netperf-2.4.5/src/netperf -t %s -H %s -l 60 -- -m 1 protocols = "TCP_STREAM TCP_MAERTS TCP_RR TCP_CRR UDP_RR TCP_SENDFILE UDP_STREAM" + - ethtool: install setup unattended_install.cdrom + type = ethtool + filesize = 512 + nic_mode = tap + - physical_resources_check: install setup unattended_install.cdrom type = physical_resources_check catch_uuid_cmd = dmidecode | awk -F: '/UUID/ {print $2}'
@@ -686,11 +691,15 @@ variants: nic_model = e1000 jumbo: mtu = 16110 + ethtool: + # gso gro lro is only supported by latest kernel + supported_features = "tx rx sg tso gso gro lro" - virtio_net: nic_model = virtio jumbo: mtu = 65520 - + ethtool: + supported_features = "tx sg tso gso" # Guests variants:
@@ -1304,7 +1313,7 @@ variants: # Windows section - @Windows: - no autotest linux_s3 vlan ioquit unattended_install.(url|nfs|remote_ks) jumbo file_transfer nicdriver_unload nic_promisc multicast mac_change + no autotest linux_s3 vlan ioquit unattended_install.(url|nfs|remote_ks) jumbo file_transfer nicdriver_unload nic_promisc multicast mac_change ethtool shutdown_command = shutdown /s /f /t 0 reboot_command = shutdown /r /f /t 0 status_test_command = echo %errorlevel%
Signature · 1 line
1.7.1
Re: [PATCH 18/18] KVM test: Add subtest of testing offload by ethtool
Quoted 16 lines · On Mon, 27 Sep 2010 18:44:04 -0400 Lucas Meneghel Rodrigues <[email protected]>…
client/tests/kvm/tests/ethtool.py new file +5
-0+ + vm = kvm_test_utils.get_living_vm(env, params.get("main_vm")) + session = kvm_test_utils.wait_for_login(vm, + timeout=int(params.get("login_timeout", 360))) + # Let's just error the test if we identify that there's noethtool installed
(quoted diff) +2
-0+ if session.get_command_status("ethtool -h"): + raise error.TestError("Command ethtool not installed onguest")
client/tests/kvm/tests/ethtool.py new file +7
-0+ session2 = kvm_test_utils.wait_for_login(vm, + timeout=int(params.get("login_timeout", 360))) + mtu = 1514 + feature_status = {} + filename = "/tmp/ethtool.dd" + guest_ip = vm.get_address() + ethname = kvm_test_utils.get_linux_ifname(session,
Quoted 2 lines
vm.get_mac_address(0))
+supported_features= params.get("supported_features").split()
I guess split this expects input.
23:48:03 ERROR| Test failed: AttributeError: 'NoneType' object has no attribute 'split'
22.12', '00:1a:4a:65:09:09': '192.168.122.66', '9a:52:2f:62:12:63':
'192.168.122.151', '9a:52:2f:62:6b:28': '192.168.122.35'}, 'version':
0, 'tcpdump': <kvm_subprocess.kvm_tail instance at 0x27cb200>} 23:48:05 INFO | ['iteration.1'] 23:48:05 ERROR| Exception escaping from test:
Traceback (most recent call last): File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py", line 412, in _exec _call_test_function(self.execute, *p_args, **p_dargs) File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py", line 605, in _call_test_function raise error.UnhandledTestFail(e)
UnhandledTestFail: Unhandled AttributeError: 'NoneType' object has no attribute 'split' Traceback (most recent call last): File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py", line 598, in _call_test_function return func(*args, **dargs) File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py", line 284, in execute postprocess_profiled_run, args, dargs) File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py", line 202, in _call_run_once self.run_once_profiling(postprocess_profiled_run, *args, **dargs) File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py", line 308, in run_once_profiling self.run_once(*args, **dargs) File "/home/pradeep/vhost_net/autotest/client/tests/kvm/kvm.py", line 73, in run_once run_func(self, params, env) File "/home/pradeep/vhost_net/autotest/client/tests/kvm/tests/ethtool.py", line 185, in run_ethtool supported_features = params.get("supported_features").split() AttributeError: 'NoneType' object has no attribute 'split'
--Pradeep
Re: [Autotest] [PATCH 18/18] KVM test: Add subtest of testing offload by ethtool
Quoted 4 lines · On Wed, 6 Oct 2010 14:26:46 +0530 pradeep <[email protected]> wrote:
On Mon, 27 Sep 2010 18:44:04 -0400
Lucas Meneghel Rodrigues <[email protected]> wrote:
Quoted 9 lines
ion,
Quoted 2 lines
vm.get_mac_address(0))
+supported_features= params.get("supported_features").split()I guess split this expects input.
23:48:03 ERROR| Test failed: AttributeError: 'NoneType' object has no attribute 'split'
Neglect my earlier mail. i was using rtl8139.
rtl8139 doesnt support this.
Quoted 5 lines
--Pradeep
_______________________________________________
Autotest mailing list
[email protected]
http://test.kernel.org/cgi-bin/mailman/listinfo/autotest
Re: [PATCH 18/18] KVM test: Add subtest of testing offload by ethtool
In reply to pradeepQuoted 23 lines · pradeep
Quoted 16 lines · On Mon, 27 Sep 2010 18:44:04 -0400 Lucas Meneghel Rodrigues <[email protected]>…
client/tests/kvm/tests/ethtool.py new file +5
-0+ + vm = kvm_test_utils.get_living_vm(env, params.get("main_vm")) + session = kvm_test_utils.wait_for_login(vm, + timeout=int(params.get("login_timeout", 360))) + # Let's just error the test if we identify that there's noethtool installed
(quoted diff) +2
-0+ if session.get_command_status("ethtool -h"): + raise error.TestError("Command ethtool not installed onguest")
client/tests/kvm/tests/ethtool.py new file +7
-0+ session2 = kvm_test_utils.wait_for_login(vm, + timeout=int(params.get("login_timeout", 360))) + mtu = 1514 + feature_status = {} + filename = "/tmp/ethtool.dd" + guest_ip = vm.get_address() + ethname = kvm_test_utils.get_linux_ifname(session,Quoted 2 lines
vm.get_mac_address(0))
+supported_features= params.get("supported_features").split()
Quoted 4 lines
I guess split this expects input.
23:48:03 ERROR| Test failed: AttributeError: 'NoneType' object has no attribute 'split'
That'll need an update to the tests_base.cfg file to ensure the test type has that config value set.
Did the patchset miss updating tests_base.cfg.sample with this one ?
Quoted 35 lines
22.12', '00:1a:4a:65:09:09': '192.168.122.66', '9a:52:2f:62:12:63':
'192.168.122.151', '9a:52:2f:62:6b:28': '192.168.122.35'}, 'version':
0, 'tcpdump': <kvm_subprocess.kvm_tail instance at0x27cb200>} 23:48:05 INFO | ['iteration.1'] 23:48:05 ERROR| Exception escaping from test:
Traceback (most recent call last): File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py", line 412, in_exec_call_test_function(self.execute, *p_args, **p_dargs)File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py", line 605, in_call_test_functionraiseerror.UnhandledTestFail(e)
UnhandledTestFail: Unhandled AttributeError: 'NoneType' object has no attribute 'split' Traceback (most recent call last): File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py", line 598, in_call_test_functionreturnfunc(*args, **dargs)File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py", line 284, in executepostprocess_profiled_run, args, dargs) File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py", line 202, in_call_run_onceself.run_once_profiling(postprocess_profiled_run, *args, **dargs)File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py", line 308, inrun_once_profilingself.run_once(*args, **dargs)File "/home/pradeep/vhost_net/autotest/client/tests/kvm/kvm.py", line 73, inrun_oncerun_func(self, params, env)File "/home/pradeep/vhost_net/autotest/client/tests/kvm/tests/ethtool.py", line 185, inrun_ethtoolsupported_features= params.get("supported_features").split() AttributeError: 'NoneType' object has no attribute 'split'--Pradeep
--
To unsubscribe from this list: send the line "unsubscribe kvm" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signature · 4 lines
Ryan Harper Software Engineer; Linux Technology Center IBM Corp., Austin, Tx [email protected]
Re: [PATCH 18/18] KVM test: Add subtest of testing offload by ethtool
Quoted 26 lines · Ryan Harper
Quoted 25 lines · pradeep
Quoted 16 lines · On Mon, 27 Sep 2010 18:44:04 -0400 Lucas Meneghel Rodrigues <[email protected]>…
client/tests/kvm/tests/ethtool.py new file +5
-0+ + vm = kvm_test_utils.get_living_vm(env, params.get("main_vm")) + session = kvm_test_utils.wait_for_login(vm, + timeout=int(params.get("login_timeout", 360))) + # Let's just error the test if we identify that there's noethtool installed
(quoted diff) +2
-0+ if session.get_command_status("ethtool -h"): + raise error.TestError("Command ethtool not installed onguest")
client/tests/kvm/tests/ethtool.py new file +7
-0+ session2 = kvm_test_utils.wait_for_login(vm, + timeout=int(params.get("login_timeout", 360))) + mtu = 1514 + feature_status = {} + filename = "/tmp/ethtool.dd" + guest_ip = vm.get_address() + ethname = kvm_test_utils.get_linux_ifname(session,Quoted 2 lines
vm.get_mac_address(0))
+supported_features= params.get("supported_features").split()I guess split this expects input.
Quoted 7 lines
Quoted 2 lines
23:48:03 ERROR| Test failed: AttributeError: 'NoneType' object has no attribute 'split'
That'll need an update to the tests_base.cfg file to ensure the test type has that config value set.
Did the patchset miss updating tests_base.cfg.sample with this one ?
I think pradeep forgot to update tests_base.cfg indeed. It's working fine for me.
Quoted 2 lines · Lucas Meneghel Rodrigues
We are close to the end of this journey. Several little problems were fixed and we are down to some little problems:
Ok, all patches applied. Thanks to everyone that helped on this effort!
Quoted 70 lines
1 - jumbo test - tap interface name shouldn't be used to stablish arp static entry, use bridge name instead - need validation from akong and/or jasonwang
2 - vlan subtest - still has some problems with it
3 - ethtool - find a way to install ethtool in guest using distro packages - this one can be easily postponedPlease give me some feedback on it.
Amos Kong (11):
KVM test: Add a new macaddress pool algorithm
KVM test: Add a new subtest ping
KVM test: Add basic file transfer test
KVM test: Add a subtest of nic promisc
KVM test: Add a subtest of multicast
KVM test: Add a subtest of pxe
KVM test: Add a subtest of changing MAC address
KVM test: Add a netperf subtest
KVM test:kvm_utils- Add support of check if remote port free KVM test: Improve vlan subtest
KVM test: vlan subtest - Replaceextra_params'-snapshot' with
image_snapshotLucas Meneghel Rodrigues (7):
KVM test: Makephysical_resources_checkto work with MAC management KVM test: Remove address_pools.cfg dependency
KVM test: Add aget_ifnamefunction
KVM Test: Add nw related functions ping andget_linux_ifnameKVM test: Add a subtest jumbo
KVM test: Add a subtest of load/unload nic driver
KVM test: Add subtest of testing offload by ethtoolclient/tests/kvm/address_pools.cfg.sample | 65 ------ client/tests/kvm/control | 8 - client/tests/kvm/control.parallel | 9 - client/tests/kvm/get_started.py | 4 +- client/tests/kvm/kvm_test_utils.py | 130 ++++++++++++- client/tests/kvm/kvm_utils.py | 139 ++++++++++++- client/tests/kvm/kvm_vm.py | 104 +++++++++- client/tests/kvm/scripts/join_mcast.py | 37 ++++ client/tests/kvm/tests/ethtool.py | 222 ++++++++++++++++++++ client/tests/kvm/tests/file_transfer.py | 58 +++++ client/tests/kvm/tests/jumbo.py | 136 ++++++++++++ client/tests/kvm/tests/mac_change.py | 68 ++++++ client/tests/kvm/tests/multicast.py | 91 ++++++++ client/tests/kvm/tests/netperf.py | 56 +++++ client/tests/kvm/tests/nic_promisc.py | 103 +++++++++ client/tests/kvm/tests/nicdriver_unload.py | 115 ++++++++++ client/tests/kvm/tests/physical_resources_check.py | 7 +- client/tests/kvm/tests/ping.py | 72 +++++++ client/tests/kvm/tests/pxe.py | 31 +++ client/tests/kvm/tests/vlan.py | 186 ++++++++++++++++ client/tests/kvm/tests/vlan_tag.py | 68 ------ client/tests/kvm/tests_base.cfg.sample | 97 ++++++++- 22 files changed, 1628 insertions(+), 178 deletions(-) delete mode 100644 client/tests/kvm/address_pools.cfg.sample create mode 100755 client/tests/kvm/scripts/join_mcast.py create mode 100644 client/tests/kvm/tests/ethtool.py create mode 100644 client/tests/kvm/tests/file_transfer.py create mode 100644 client/tests/kvm/tests/jumbo.py create mode 100644 client/tests/kvm/tests/mac_change.py create mode 100644 client/tests/kvm/tests/multicast.py create mode 100644 client/tests/kvm/tests/netperf.py create mode 100644 client/tests/kvm/tests/nic_promisc.py create mode 100644 client/tests/kvm/tests/nicdriver_unload.py create mode 100644 client/tests/kvm/tests/ping.py create mode 100644 client/tests/kvm/tests/pxe.py create mode 100644 client/tests/kvm/tests/vlan.py delete mode 100644 client/tests/kvm/tests/vlan_tag.py
Quoted 6 lines · On Wed, 06 Oct 2010 23:09:33 -0300 Lucas Meneghel Rodrigues <[email protected]>…
Quoted 2 lines · Lucas Meneghel Rodrigues
We are close to the end of this journey. Several little problems were fixed and we are down to some little problems:
Ok, all patches applied. Thanks to everyone that helped on this effort!
Thanks for applying all patches to upstream. Can you push vhost_net patch also.
Please find, my below attached test results on RHEL 5.5, RHEL 6 guests(vhost enabled)
I find issues with macchange & guest_s4 code. We need to fix this as well. Will send erros in a separate mail.
Thanks
Pradeep
Quoted 10 lines · pradeep
Quoted 6 lines · On Wed, 06 Oct 2010 23:09:33 -0300 Lucas Meneghel Rodrigues <[email protected]>…
Quoted 2 lines · Lucas Meneghel Rodrigues
We are close to the end of this journey. Several little problems were fixed and we are down to some little problems:
Ok, all patches applied. Thanks to everyone that helped on this effort!
Quoted 8 lines
Thanks for applying all patches to upstream. Can you push
vhost_netpatch also.
Please find, my below attached test results on RHEL 5.5, RHEL 6 guests(vhost enabled)I find issues with macchange &
guest_s4code. We need to fix this as well. Will send erros in a separate mail.
I tested macchange quite a lot, so I wonder what the problem is. About guest_s4, interesting, we've been running this for a while, with no apparent problems. Please let us know and let's fix it ASAP.
Cheers,
Lucas
Quoted 3 lines
Thanks
Pradeep
Quoted 5 lines · On Thu, 07 Oct 2010 10:54:16 -0300 Lucas Meneghel Rodrigues <[email protected]>…
I tested macchange quite a lot, so I wonder what the problem is. About
guest_s4, interesting, we've been running this for a while, with no apparent problems. Please let us know and let's fix it ASAP.
I hope you have checked attachment in my previous mail for other failures with vhost_net.
Reg Mac change:
---------------
10/07 21:58:45 ERROR| kvm:0080| Test failed: TestFail: Could not
log into guest 'vm1' 10/07 21:59:00 ERROR| test:0415| Exception
escaping from test: Traceback (most recent call last):
File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py",
line 412, in _exec _call_test_function(self.execute, *p_args, **p_dargs)
File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py",
line 598, in _call_test_function return func(*args, **dargs)
File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py",
line 284, in execute postprocess_profiled_run, args, dargs)
File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py",
line 202, in _call_run_once self.run_once_profiling(postprocess_profiled_run, *args, **dargs) File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py", line 308, in run_once_profiling self.run_once(*args, **dargs) File "/home/pradeep/vhost_net/autotest/client/tests/kvm/kvm.py", line 73, in run_once run_func(self, params, env) File "/home/pradeep/vhost_net/autotest/client/tests/kvm/tests/mac_change.py", line 24, in run_mac_change raise error.TestFail("Could not log into guest '%s'" % vm.name) TestFail: Could not log into guest 'vm1'
guest_s4
--------
After suspending the guest, autotest fails to bring it back.
10:43:51 DEBUG| Could not verify MAC-IP address mapping:
9a:18:2d:12:c9:56 ---> 10.168.0.9 10:43:51 DEBUG| IP address or port unavailable 10:43:56 DEBUG| Could not verify MAC-IP address mapping:
9a:18:2d:12:c9:56 ---> 10.168.0.9 10:43:56 DEBUG| IP address or port unavailable 10:44:00 DEBUG| (address cache) Adding cache entry:
02:18:0a:cc:59:c0 ---> 10.168.0.8 10:44:00 DEBUG| (address cache) Adding cache entry: 02:18:0a:cc:59:c0 ---> 10.168.0.8 10:44:01 DEBUG| Could not verify MAC-IP address mapping: 9a:18:2d:12:c9:56 ---> 10.168.0.9 10:44:01 DEBUG| IP address or port unavailable 10:44:06 DEBUG| Could not verify MAC-IP address mapping: 9a:18:2d:12:c9:56 ---> 10.168.0.9 10:44:06 DEBUG| IP address or port unavailable 10:44:08 DEBUG| Timeout elapsed 10:44:08 ERROR| Test failed: TestFail: Could not log into VM after resuming from suspend to disk 10:44:08 DEBUG| Postprocessing VM 'vm1'...
Thanks
Pradeep
Quoted 28 lines · pradeep
Quoted 5 lines · On Thu, 07 Oct 2010 10:54:16 -0300 Lucas Meneghel Rodrigues <[email protected]>…
I tested macchange quite a lot, so I wonder what the problem is. About
guest_s4, interesting, we've been running this for a while, with no apparent problems. Please let us know and let's fix it ASAP.I hope you have checked attachment in my previous mail for other failures with
vhost_net.Reg Mac change:
---------------10/07 21:58:45 ERROR| kvm:0080| Test failed: TestFail: Could not
log into guest 'vm1' 10/07 21:59:00 ERROR| test:0415| Exception
escaping from test: Traceback (most recent call last):
File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py",
line 412, in_exec_call_test_function(self.execute, *p_args, **p_dargs)
File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py",
line 598, in_call_test_functionreturnfunc(*args, **dargs)
File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py",
line 284, in executepostprocess_profiled_run, args, dargs)
File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py",
line 202, in_call_run_once
Quoted 8 lines
self.run_once_profiling(postprocess_profiled_run, *args, **dargs)File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py", line 308, inrun_once_profilingself.run_once(*args, **dargs)File "/home/pradeep/vhost_net/autotest/client/tests/kvm/kvm.py", line 73, inrun_oncerun_func(self, params, env)File "/home/pradeep/vhost_net/autotest/client/tests/kvm/tests/mac_change.py", line 24, inrun_mac_changeraiseerror.TestFail("Could not log into guest '%s'" % vm.name)TestFail: Could not log into guest 'vm1'
What happens here exactly?
Quoted 19 lines
guest_s4
--------
After suspending the guest, autotest fails to bring it back.10:43:51 DEBUG| Could not verify MAC-IP address mapping:
9a:18:2d:12:c9:56 ---> 10.168.0.9 10:43:51 DEBUG| IP address or port unavailable 10:43:56 DEBUG| Could not verify MAC-IP address mapping:
9a:18:2d:12:c9:56 ---> 10.168.0.9 10:43:56 DEBUG| IP address or port unavailable 10:44:00 DEBUG| (address cache) Adding cache entry:
02:18:0a:cc:59:c0 ---> 10.168.0.8 10:44:00 DEBUG| (address cache) Adding cache entry: 02:18:0a:cc:59:c0 ---> 10.168.0.8 10:44:01 DEBUG| Could not verify MAC-IP address mapping: 9a:18:2d:12:c9:56 ---> 10.168.0.9 10:44:01 DEBUG| IP address or port unavailable 10:44:06 DEBUG| Could not verify MAC-IP address mapping: 9a:18:2d:12:c9:56 ---> 10.168.0.9 10:44:06 DEBUG| IP address or port unavailable 10:44:08 DEBUG| Timeout elapsed 10:44:08 ERROR| Test failed: TestFail: Could not log into VM after resuming from suspend to disk 10:44:08 DEBUG| Postprocessing VM 'vm1'...
Quoted 2 lines
Thanks
Pradeep
I just sent a pull request to qemu.git which might fix this. It'll get to qemu-kvm in several says I hope.
Signature · 1 line
MST
Quoted 38 lines · Michael S. Tsirkin
Quoted 28 lines · pradeep
Quoted 5 lines · On Thu, 07 Oct 2010 10:54:16 -0300 Lucas Meneghel Rodrigues <[email protected]>…
I tested macchange quite a lot, so I wonder what the problem is. About
guest_s4, interesting, we've been running this for a while, with no apparent problems. Please let us know and let's fix it ASAP.I hope you have checked attachment in my previous mail for other failures with
vhost_net.Reg Mac change:
---------------10/07 21:58:45 ERROR| kvm:0080| Test failed: TestFail: Could not
log into guest 'vm1' 10/07 21:59:00 ERROR| test:0415| Exception
escaping from test: Traceback (most recent call last):
File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py",
line 412, in_exec_call_test_function(self.execute, *p_args, **p_dargs)
File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py",
line 598, in_call_test_functionreturnfunc(*args, **dargs)
File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py",
line 284, in executepostprocess_profiled_run, args, dargs)
File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py",
line 202, in_call_run_onceQuoted 8 lines
self.run_once_profiling(postprocess_profiled_run, *args, **dargs)File "/home/pradeep/vhost_net/autotest/client/common_lib/test.py", line 308, inrun_once_profilingself.run_once(*args, **dargs)File "/home/pradeep/vhost_net/autotest/client/tests/kvm/kvm.py", line 73, inrun_oncerun_func(self, params, env)File "/home/pradeep/vhost_net/autotest/client/tests/kvm/tests/mac_change.py", line 24, inrun_mac_changeraiseerror.TestFail("Could not log into guest '%s'" % vm.name)TestFail: Could not log into guest 'vm1'
Quoted 1 line
What happens here exactly?
^ Here it wasn't possible to stablish an ssh connection to a host. When that happens, we throw this "Could not log into guest [vm]" message.