Skip to contentSkip to conversation

MX31: add support for setting pin pads

PATCH New Stefano Babic 3 participants 6 messages Oct 7, 2010 – Oct 13, 2010

Subsystems (5)
lore
Share & tools
lore
#0 lore raw

PATCH 1/3 MX31: add support for setting pin pads

The patch adds a utility function and defines
to set the pad as it is done in linux.

---
 arch/arm/cpu/arm1136/mx31/generic.c        |   17 ++
 arch/arm/include/asm/arch-mx31/mx31-regs.h |  404 ++++++++++++++++++++++++++++
 drivers/video/mx3fb.c                      |   31 ---
 3 files changed, 421 insertions(+), 31 deletions(-)
arch/arm/cpu/arm1136/mx31/generic.c +17 -0
index 1415d6c..cbe8243 100644
@@ -23,6 +23,7 @@
 
 #include <common.h>
 #include <asm/arch/mx31-regs.h>
+#include <asm/io.h>
 
 static u32 mx31_decode_pll(u32 reg, u32 infreq)
 {
@@ -90,6 +91,22 @@ void mx31_gpio_mux(unsigned long mode)
 	__REG(reg) = tmp;
 }
 
+void mx31_set_pad(enum iomux_pins pin, u32 config)
+{
+	u32 field, l;
+	void *reg;
+
+	pin &= IOMUX_PADNUM_MASK;
+	reg = (IOMUXC_BASE + 0x154) + (pin + 2) / 3 * 4;
+	field = (pin + 2) % 3;
+
+	l = __raw_readl(reg);
+	l &= ~(0x1ff << (field * 10));
+	l |= config << (field * 10);
+	__raw_writel(l, reg);
+
+}
+
 #if defined(CONFIG_DISPLAY_CPUINFO)
 int print_cpuinfo (void)
 {
arch/arm/include/asm/arch-mx31/mx31-regs.h +404 -0

426 lines not on this page · raw message

drivers/video/mx3fb.c +0 -31
index 7f04b49..51831f0 100644
@@ -334,37 +334,6 @@ enum ipu_panel {
 
 #define IOMUX_MODE_L(pin, mode) IOMUX_MODE(((pin) + 0xc) ^ 3, mode)
 
-enum lcd_pin {
-	MX31_PIN_D3_SPL		= IOMUX_PIN(0xff,  19),
-	MX31_PIN_D3_CLS		= IOMUX_PIN(0xff,  20),
-	MX31_PIN_D3_REV		= IOMUX_PIN(0xff,  21),
-	MX31_PIN_CONTRAST	= IOMUX_PIN(0xff,  22),
-	MX31_PIN_VSYNC3		= IOMUX_PIN(0xff,  23),
-
-	MX31_PIN_DRDY0		= IOMUX_PIN(0xff,  33),
-	MX31_PIN_FPSHIFT	= IOMUX_PIN(0xff,  34),
-	MX31_PIN_HSYNC		= IOMUX_PIN(0xff,  35),
-
-	MX31_PIN_LD17		= IOMUX_PIN(0xff,  37),
-	MX31_PIN_LD16		= IOMUX_PIN(0xff,  38),
-	MX31_PIN_LD15		= IOMUX_PIN(0xff,  39),
-	MX31_PIN_LD14		= IOMUX_PIN(0xff,  40),
-	MX31_PIN_LD13		= IOMUX_PIN(0xff,  41),
-	MX31_PIN_LD12		= IOMUX_PIN(0xff,  42),
-	MX31_PIN_LD11		= IOMUX_PIN(0xff,  43),
-	MX31_PIN_LD10		= IOMUX_PIN(0xff,  44),
-	MX31_PIN_LD9		= IOMUX_PIN(0xff,  45),
-	MX31_PIN_LD8		= IOMUX_PIN(0xff,  46),
-	MX31_PIN_LD7		= IOMUX_PIN(0xff,  47),
-	MX31_PIN_LD6		= IOMUX_PIN(0xff,  48),
-	MX31_PIN_LD5		= IOMUX_PIN(0xff,  49),
-	MX31_PIN_LD4		= IOMUX_PIN(0xff,  50),
-	MX31_PIN_LD3		= IOMUX_PIN(0xff,  51),
-	MX31_PIN_LD2		= IOMUX_PIN(0xff,  52),
-	MX31_PIN_LD1		= IOMUX_PIN(0xff,  53),
-	MX31_PIN_LD0		= IOMUX_PIN(0xff,  54),
-};
-
 struct chan_param_mem_planar {
 	/* Word 0 */
 	u32	xv:10;
Signature · 1 line
1.6.3.3
#1 lore raw

PATCH 2/3 MX31: Add support for MXC EHCI controller

The patch adds the EHCI controller for the i.MX31 Soc.

---
 drivers/usb/host/Makefile   |    1 +
 drivers/usb/host/ehci-mxc.c |  130 +++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 131 insertions(+), 0 deletions(-)
 create mode 100644 drivers/usb/host/ehci-mxc.c
drivers/usb/host/Makefile +1 -0
index 255679a..399520e 100644
@@ -36,6 +36,7 @@ COBJS-$(CONFIG_USB_SL811HS) += sl811-hcd.o
 # echi
 COBJS-$(CONFIG_USB_EHCI) += ehci-hcd.o
 COBJS-$(CONFIG_USB_EHCI_FSL) += ehci-fsl.o
+COBJS-$(CONFIG_USB_EHCI_MXC) += ehci-mxc.o
 COBJS-$(CONFIG_USB_EHCI_PPC4XX) += ehci-ppc4xx.o
 COBJS-$(CONFIG_USB_EHCI_IXP4XX) += ehci-ixp.o
 COBJS-$(CONFIG_USB_EHCI_KIRKWOOD) += ehci-kirkwood.o
drivers/usb/host/ehci-mxc.c new file +130 -0

130 lines not on this page · raw message

Signature · 1 line
1.6.3.3
#2 lore raw

PATCH 3/3 MX31: Add USB Host support to the QONG board

---
 board/davedenx/qong/qong.c |   33 +++++++++++++++++++++++++++++++++
 include/configs/qong.h     |   18 +++++++++++++++++-
 2 files changed, 50 insertions(+), 1 deletions(-)
board/davedenx/qong/qong.c +33 -0
index efeb0bb..8a81cfc 100644
@@ -25,6 +25,7 @@
 #include <netdev.h>
 #include <asm/arch/mx31.h>
 #include <asm/arch/mx31-regs.h>
+#include <asm/io.h>
 #include <nand.h>
 #include <fsl_pmic.h>
 #include <mxc_gpio.h>
@@ -97,6 +98,38 @@ int board_early_init_f (void)
 	mx31_gpio_mux(MUX_CSPI2_SCLK__CSPI2_CLK);
 	mx31_gpio_mux(MUX_CSPI2_SPI_RDY__CSPI2_DATAREADY_B);
 
+	/* Setup pins for USB2 Host */
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_CLK, MUX_CTL_FUNC));
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_DIR, MUX_CTL_FUNC));
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_NXT, MUX_CTL_FUNC));
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_STP, MUX_CTL_FUNC));
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_DATA0, MUX_CTL_FUNC));
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_USBH2_DATA1, MUX_CTL_FUNC));
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_STXD3, MUX_CTL_FUNC));
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SRXD3, MUX_CTL_FUNC));
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SCK3, MUX_CTL_FUNC));
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SFS3, MUX_CTL_FUNC));
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_STXD6, MUX_CTL_FUNC));
+	mx31_gpio_mux(IOMUX_MODE(MUX_CTL_SRXD6, MUX_CTL_FUNC));
+
+#define H2_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
+			PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
+
+	mx31_set_pad(MX31_PIN_USBH2_CLK, H2_PAD_CFG);
+	mx31_set_pad(MX31_PIN_USBH2_DIR, H2_PAD_CFG);
+	mx31_set_pad(MX31_PIN_USBH2_NXT, H2_PAD_CFG);
+	mx31_set_pad(MX31_PIN_USBH2_STP, H2_PAD_CFG);
+	mx31_set_pad(MX31_PIN_USBH2_DATA0, H2_PAD_CFG); /* USBH2_DATA0 */
+	mx31_set_pad(MX31_PIN_USBH2_DATA1, H2_PAD_CFG); /* USBH2_DATA1 */
+	mx31_set_pad(MX31_PIN_SRXD6, H2_PAD_CFG);	/* USBH2_DATA2 */
+	mx31_set_pad(MX31_PIN_STXD6, H2_PAD_CFG);	/* USBH2_DATA3 */
+	mx31_set_pad(MX31_PIN_SFS3, H2_PAD_CFG);	/* USBH2_DATA4 */
+	mx31_set_pad(MX31_PIN_SCK3, H2_PAD_CFG);	/* USBH2_DATA5 */
+	mx31_set_pad(MX31_PIN_SRXD3, H2_PAD_CFG);	/* USBH2_DATA6 */
+	mx31_set_pad(MX31_PIN_STXD3, H2_PAD_CFG);	/* USBH2_DATA7 */
+
+	writel(readl((IOMUXC_BASE + 0x8)) | (1 << 11), IOMUXC_BASE + 0x8);
+
 	return 0;
 
 }
include/configs/qong.h +17 -1
index 2d124ea..fef8094 100644
@@ -89,6 +89,22 @@
 #define CONFIG_BMP_16BPP
 #define CONFIG_DISPLAY_COM57H5M10XRC
 
+/* USB */
+#define CONFIG_CMD_USB
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI			/* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_MXC
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORT	2
+#define CONFIG_MXC_USB_PORTSC	(MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT)
+#define CONFIG_MXC_USB_FLAGS	MXC_EHCI_POWER_PINS_ENABLED
+#define CONFIG_EHCI_IS_TDI
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#define CONFIG_CMD_FAT
+#endif /* CONFIG_CMD_USB */
+
 /*
  * Reducing the ARP timeout from default 5 seconds to 200ms we speed up the
  * initial TFTP transfer, should the user wish one, significantly.
@@ -250,7 +266,7 @@ extern int qong_nand_rdy(void *chip);
 #define	CONFIG_ENV_IS_IN_FLASH	1
 #define CONFIG_ENV_SECT_SIZE	0x20000
 #define CONFIG_ENV_SIZE		CONFIG_ENV_SECT_SIZE
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x60000)
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x80000)
 
 /* Address and size of Redundant Environment Sector	*/
 #define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
Signature · 1 line
1.6.3.3
#3 lore raw

PATCH 3/3 MX31: Add USB Host support to the QONG board

Dear Remy,

Quoted 5 lines · In message <[email protected]> you wrote:
---
 board/davedenx/qong/qong.c |   33 +++++++++++++++++++++++++++++++++
 include/configs/qong.h     |   18 +++++++++++++++++-
 2 files changed, 50 insertions(+), 1 deletions(-)

even though USB related, this looks like a board specific patch to me. Is it OK with you that Stefano pulls this through the iMX repository?

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
A conservative is a man who believes that nothing should be done for
the first time.                                   - Alfred E. Wiggam
#4 lore raw

PATCH 3/3 MX31: Add USB Host support to the QONG board

Hi,

2010/10/11 Wolfgang Denk <[email protected]>:

Quoted 12 lines

Dear Remy,

Quoted 5 lines · In message <[email protected]> you wrote:

---
?board/davedenx/qong/qong.c | ? 33 +++++++++++++++++++++++++++++++++ ?include/configs/qong.h ? ? | ? 18 +++++++++++++++++-
?2 files changed, 50 insertions(+), 1 deletions(-)

even though USB related, this looks like a board specific patch to me. Is it OK with you that Stefano pulls this through the iMX repository?

OK with me.

Remy

#5 lore raw

PATCH 3/3 MX31: Add USB Host support to the QONG board

Quoted 6 lines · Remy Bohmer
Quoted 3 lines

even though USB related, this looks like a board specific patch to me. Is it OK with you that Stefano pulls this through the iMX repository?

OK with me.

Hi Remy,

thanks - I will merge in u-boot-imx and sent the pull request to Wolfgang

Stefano

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================