Skip to contentSkip to conversation

Kirkwood: dram_init is moved to dram.c

PATCH New Prafulla Wadaskar 3 participants 9 messages Oct 7, 2010 – Oct 12, 2010 Arm (32-bit)

lore
Share & tools
lore
#0 lore raw

PATCH v2 1/3 Kirkwood: dram_init is moved to dram.c

For all Kirkwood boards so far dram_init function is duplicated dram_init function is moved to dram.c and relevant code from all board specific files removed

If any board needs specific dram init handling than standard one, then, a macro CONFIG_SYS_BOARD_DRAM_INIT should be defined in board config header file and the dram_init function can be put in board specific source file
For ex. keymile boards

---
Changelog
v2:
dram_init only performed for consecutive memory
removed CONFIG_SYS_WITHOUT_RELOC dependency dram_init_banksize added to avoid re-configuration of dram bank 0

 arch/arm/cpu/arm926ejs/kirkwood/dram.c          |   38 +++++++++++++++++++++++
 board/Marvell/guruplug/guruplug.c               |   11 ------
 board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c |   11 ------
 board/Marvell/openrd_base/openrd_base.c         |   11 ------
 board/Marvell/rd6281a/rd6281a.c                 |   11 ------
 board/Marvell/sheevaplug/sheevaplug.c           |   11 ------
 include/configs/keymile-common.h                |    1 +
 7 files changed, 39 insertions(+), 55 deletions(-)
arch/arm/cpu/arm926ejs/kirkwood/dram.c +38 -0
index 8f2a18a..cb29f97 100644
@@ -23,8 +23,11 @@
  */
 
 #include <config.h>
+#include <common.h>
 #include <asm/arch/kirkwood.h>
 
+DECLARE_GLOBAL_DATA_PTR;
+
 #define KW_REG_CPUCS_WIN_BAR(x)		(KW_REGISTER(0x1500) + (x * 0x08))
 #define KW_REG_CPUCS_WIN_SZ(x)		(KW_REGISTER(0x1504) + (x * 0x08))
 /*
@@ -56,3 +59,38 @@ u32 kw_sdram_bs(enum memory_bank bank)
 	result += 0x01000000;
 	return result;
 }
+
+#ifndef CONFIG_SYS_BOARD_DRAM_INIT
+int dram_init(void)
+{
+	int i;
+
+	gd->ram_size = 0;
+	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+		gd->bd->bi_dram[i].start = kw_sdram_bar(i);
+		gd->bd->bi_dram[i].size = kw_sdram_bs(i);
+		/*
+		 * It is assumed that all memory banks are consecutive
+		 * and without gaps.
+		 * If the gap is found, ram_size will be reported for
+		 * consecutive memory only
+		 */
+		if (gd->bd->bi_dram[i].start != gd->ram_size)
+			break;
+
+		gd->ram_size += gd->bd->bi_dram[i].size;
+
+	}
+	return 0;
+}
+
+/*
+ * If this function is not defined here,
+ * board.c alters dram bank zero configuration defined above.
+ */
+void dram_init_banksize(void)
+{
+	dram_init();
+}
+#endif /* CONFIG_SYS_BOARD_DRAM_INIT */
+
board/Marvell/guruplug/guruplug.c +0 -11
index c028a53..4df4e9b 100644
@@ -108,17 +108,6 @@ int board_init(void)
 	return 0;
 }
 
-int dram_init(void)
-{
-	int i;
-
-	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
-		gd->bd->bi_dram[i].start = kw_sdram_bar(i);
-		gd->bd->bi_dram[i].size = kw_sdram_bs(i);
-	}
-	return 0;
-}
-
 #ifdef CONFIG_RESET_PHY_R
 void mv_phy_88e1121_init(char *name)
 {
board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c +0 -11
index c959bf8..93d1400 100644
@@ -110,17 +110,6 @@ int board_init(void)
 	return 0;
 }
 
-int dram_init(void)
-{
-	int i;
-
-	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
-		gd->bd->bi_dram[i].start = kw_sdram_bar(i);
-		gd->bd->bi_dram[i].size = kw_sdram_bs(i);
-	}
-	return 0;
-}
-
 #ifdef CONFIG_MV88E61XX_SWITCH
 void reset_phy(void)
 {
board/Marvell/openrd_base/openrd_base.c +0 -11
index c00a08a..d006b2d 100644
@@ -113,17 +113,6 @@ int board_init(void)
 	return 0;
 }
 
-int dram_init(void)
-{
-	int i;
-
-	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
-		gd->bd->bi_dram[i].start = kw_sdram_bar(i);
-		gd->bd->bi_dram[i].size = kw_sdram_bs(i);
-	}
-	return 0;
-}
-
 #ifdef CONFIG_RESET_PHY_R
 /* Configure and enable MV88E1116 PHY */
 void reset_phy(void)
board/Marvell/rd6281a/rd6281a.c +0 -11
index 8713a3c..0d76146 100644
@@ -109,17 +109,6 @@ int board_init(void)
 	return 0;
 }
 
-int dram_init(void)
-{
-	int i;
-
-	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
-		gd->bd->bi_dram[i].start = kw_sdram_bar(i);
-		gd->bd->bi_dram[i].size = kw_sdram_bs(i);
-	}
-	return 0;
-}
-
 void mv_phy_88e1116_init(char *name)
 {
 	u16 reg;
board/Marvell/sheevaplug/sheevaplug.c +0 -11
index 547126a..173a7b8 100644
@@ -108,17 +108,6 @@ int board_init(void)
 	return 0;
 }
 
-int dram_init(void)
-{
-	int i;
-
-	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
-		gd->bd->bi_dram[i].start = kw_sdram_bar(i);
-		gd->bd->bi_dram[i].size = kw_sdram_bs(i);
-	}
-	return 0;
-}
-
 #ifdef CONFIG_RESET_PHY_R
 /* Configure and enable MV88E1116 PHY */
 void reset_phy(void)
include/configs/keymile-common.h +1 -0
index 6c14ca0..62d21f6 100644
@@ -85,6 +85,7 @@
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+#define CONFIG_SYS_BOARD_DRAM_INIT	/* Used board specific dram_init */
 
 /*
  * How to get access to the slot ID.  Put this here to make it easy
Signature · 1 line
1.5.3.3
#1 lore raw

PATCH v2 1/3 Kirkwood: dram_init is moved to dram.c

Quoted 27 lines

-----Original Message-----
From: Prafulla Wadaskar [mailto:prafulla at marvell.com]
Sent: Thursday, October 07, 2010 8:29 PM
To: u-boot at lists.denx.de
Cc: Prabhanjan Sarnaik; Ashish Karkare; Prafulla Wadaskar
Subject: [PATCH V2 1/3] Kirkwood: dram_init is moved to dram.c

For all Kirkwood boards so far dram_init function is duplicated dram_init function is moved to dram.c and relevant code from all board specific files removed

If any board needs specific dram init handling than standard one, then, a macro CONFIG_SYS_BOARD_DRAM_INIT should be defined in board config header file and the dram_init function can be put in board specific source file
For ex. keymile boards

---
Changelog
v2:
dram_init only performed for consecutive memory
removed CONFIG_SYS_WITHOUT_RELOC dependency dram_init_banksize added to avoid re-configuration of dram bank 0

Quoted 10 lines
 arch/arm/cpu/arm926ejs/kirkwood/dram.c          |   38 
+++++++++++++++++++++++
 board/Marvell/guruplug/guruplug.c               |   11 ------
 board/Marvell/mv88f6281gtw_ge/mv88f6281gtw_ge.c |   11 ------
 board/Marvell/openrd_base/openrd_base.c         |   11 ------
 board/Marvell/rd6281a/rd6281a.c                 |   11 ------
 board/Marvell/sheevaplug/sheevaplug.c           |   11 ------
 include/configs/keymile-common.h                |    1 +
 7 files changed, 39 insertions(+), 55 deletions(-)

Applied to u-boot-marvell.git master branch

Regards.
Prafulla . .

#2 lore raw

PATCH v2 2/3 kirkwood: added common config file mv-common.h

In reply to Prafulla Wadaskar

It is observed that, in most of the board configs the code is being duplicated, also for any common change all board files needs update This issue was under discussion from long on mailing list and we converge on introducing common config file.

With this patch-
1. Total Kirkwood specific configuration code is reduced by 210 lines
2. All common configuration can be shared by multiple boards
3. Easy to manage common updates like ARM relocation changes

mv-common.h file is added to include/configs/
It contains all common configuration supported for all Kirkwood boards The respective board configs are updated for its usage

Build tested for guruplug, mv88f6281gtw_ge, openrd_base, rd6281a and sheevaplug
Binary execution tested for sheevaplug

Todo:
1. Other custom Kirkwood boards to be synced
2. The support to be extended for Orion5X based boards

---
Changelog:
v2: patch description updated for s/mv-config/mv-common/ SATA port configs made board specific
changed IDe typo with IDE

 include/configs/guruplug.h        |  103 ++----------------
 include/configs/mv-common.h       |  225 +++++++++++++++++++++++++++++++++++++
 include/configs/mv88f6281gtw_ge.h |  120 ++------------------
 include/configs/openrd_base.h     |  146 ++-----------------------
 include/configs/rd6281a.h         |  101 ++---------------
 include/configs/sheevaplug.h      |  104 +-----------------
 6 files changed, 266 insertions(+), 533 deletions(-)
 create mode 100644 include/configs/mv-common.h
include/configs/guruplug.h +8 -95
index eb3fa57..2c2682c 100644
@@ -33,59 +33,13 @@
 /*
  * High Level Configuration Options (easy to change)
  */
-#define CONFIG_MARVELL		1
-#define CONFIG_ARM926EJS	1	/* Basic Architecture */
 #define CONFIG_SHEEVA_88SV131	1	/* CPU Core subversion */
 #define CONFIG_KIRKWOOD		1	/* SOC Family Name */
 #define CONFIG_KW88F6281	1	/* SOC Name */
 #define CONFIG_MACH_GURUPLUG	/* Machine type */
-
-#define CONFIG_MD5	/* get_random_hex on krikwood needs MD5 support */
 #define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
-#define CONFIG_KIRKWOOD_EGIGA_INIT	/* Enable GbePort0/1 for kernel */
-#define CONFIG_KIRKWOOD_RGMII_PAD_1V8	/* Set RGMII Pad voltage to 1.8V */
-
-/*
- * CLKs configurations
- */
-#define CONFIG_SYS_HZ		1000
-
-/*
- * NS16550 Configuration
- */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	(-4)
-#define CONFIG_SYS_NS16550_CLK		CONFIG_SYS_TCLK
-#define CONFIG_SYS_NS16550_COM1		KW_UART0_BASE
-
-/*
- * Serial Port configuration
- * The following definitions let you select what serial you want to use
- * for your console driver.
- */
-
-#define CONFIG_CONS_INDEX	1	/*Console on UART0 */
-#define CONFIG_BAUDRATE			115200
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, \
-					  115200,230400, 460800, 921600 }
-/* auto boot */
-#define CONFIG_BOOTDELAY	3	/* default enable autoboot */
 
 /*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_CMDLINE_TAG	1	/* enable passing of ATAGs  */
-#define CONFIG_INITRD_TAG	1	/* enable INITRD tag */
-#define CONFIG_SETUP_MEMORY_TAGS 1	/* enable memory tag */
-
-#define	CONFIG_SYS_PROMPT	"Marvell>> "	/* Command Prompt */
-#define	CONFIG_SYS_CBSIZE	1024	/* Console I/O Buff Size */
-#define	CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE \
-		+sizeof(CONFIG_SYS_PROMPT) + 16)	/* Print Buff */
-/*
  * Commands configuration
  */
 #define CONFIG_SYS_NO_FLASH		/* Declare no flash (NOR/SPI) */
@@ -96,18 +50,13 @@
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_USB
+#define CONFIG_CMD_IDE
 
 /*
- * NAND configuration
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
  */
-#ifdef CONFIG_CMD_NAND
-#define CONFIG_NAND_KIRKWOOD
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define NAND_MAX_CHIPS			1
-#define CONFIG_SYS_NAND_BASE		0xD8000000	/* KW_DEFADR_NANDF */
-#define NAND_ALLOW_ERASE_ALL		1
-#define CONFIG_SYS_64BIT_VSPRINTF	/* needed for nand_util.c */
-#endif
+#include "mv-common.h"
 
 /*
  *  Environment variables configurations
@@ -143,55 +92,19 @@
 	"x_bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs\0"
 
 /*
- * Size of malloc() pool
- */
-#define CONFIG_SYS_MALLOC_LEN	(1024 * 128) /* 128kB for malloc() */
-/* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_SIZE	128
-
-/*
- * Other required configurations
- */
-#define CONFIG_CONSOLE_INFO_QUIET	/* some code reduction */
-#define CONFIG_ARCH_CPU_INIT	/* call arch_cpu_init() */
-#define CONFIG_ARCH_MISC_INIT	/* call arch_misc_init() */
-#define CONFIG_DISPLAY_CPUINFO	/* Display cpu info */
-#define CONFIG_NR_DRAM_BANKS	4
-#define CONFIG_STACKSIZE	0x00100000	/* regular stack- 1M */
-#define CONFIG_SYS_LOAD_ADDR	0x00800000	/* default load adr- 8M */
-#define CONFIG_SYS_MEMTEST_START 0x00800000	/* 8M */
-#define CONFIG_SYS_MEMTEST_END	0x1fffffff	/*(_512M -1) */
-#define CONFIG_SYS_RESET_ADDRESS 0xffff0000	/* Rst Vector Adr */
-#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
-
-/*
  * Ethernet Driver configuration
  */
 #ifdef CONFIG_CMD_NET
-#define CONFIG_NETCONSOLE	/* include NetConsole support   */
-#define CONFIG_NET_MULTI	/* specify more that one ports available */
-#define CONFIG_MII		/* expose smi ove miiphy interface */
-#define CONFIG_CMD_MII
-#define CONFIG_MVGBE		/* Enable Marvell Gbe Controller Driver */
-#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	/* detect link using phy */
 #define CONFIG_MVGBE_PORTS	{1, 1}	/* enable both ports */
 #define CONFIG_PHY_BASE_ADR	0
-#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
-#define CONFIG_RESET_PHY_R	/* use reset_phy() to init mv88e1121 PHY */
 #endif /* CONFIG_CMD_NET */
 
 /*
- * USB/EHCI
+ * SATA Driver configuration
  */
-#ifdef CONFIG_CMD_USB
-#define CONFIG_USB_EHCI			/* Enable EHCI USB support */
-#define CONFIG_USB_EHCI_KIRKWOOD	/* on Kirkwood platform	*/
-#define CONFIG_EHCI_IS_TDI
-#define CONFIG_USB_STORAGE
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-#define CONFIG_SUPPORT_VFAT
-#endif /* CONFIG_CMD_USB */
+#ifdef CONFIG_MVSATA_IDE
+#define CONFIG_SYS_ATA_IDE0_OFFSET	MV_SATA_PORT0_OFFSET
+#endif /*CONFIG_MVSATA_IDE*/
 
 #define CONFIG_SYS_ALT_MEMTEST
 
include/configs/mv-common.h new file +225 -0

225 lines not on this page · raw message

include/configs/mv88f6281gtw_ge.h +13 -107

155 lines not on this page · raw message

include/configs/openrd_base.h +8 -138

179 lines not on this page · raw message

include/configs/rd6281a.h +9 -92

141 lines not on this page · raw message

include/configs/sheevaplug.h +3 -101

143 lines not on this page · raw message

Signature · 1 line
1.5.3.3
#3 lore raw

PATCH v2 2/3 kirkwood: added common config file mv-common.h

Quoted 38 lines

-----Original Message-----
From: Prafulla Wadaskar [mailto:prafulla at marvell.com]
Sent: Thursday, October 07, 2010 8:29 PM
To: u-boot at lists.denx.de
Cc: Prabhanjan Sarnaik; Ashish Karkare; Prafulla Wadaskar
Subject: [PATCH V2 2/3] kirkwood: added common config file mv-common.h

It is observed that, in most of the board configs the code is being duplicated, also for any common change all board files needs update This issue was under discussion from long on mailing list and we converge on introducing common config file.

With this patch-
1. Total Kirkwood specific configuration code is reduced by 210 lines
2. All common configuration can be shared by multiple boards
3. Easy to manage common updates like ARM relocation changes

mv-common.h file is added to include/configs/
It contains all common configuration supported for all Kirkwood boards The respective board configs are updated for its usage

Build tested for guruplug, mv88f6281gtw_ge, openrd_base, rd6281a and sheevaplug
Binary execution tested for sheevaplug

Todo:
1. Other custom Kirkwood boards to be synced
2. The support to be extended for Orion5X based boards

---
Changelog:
v2: patch description updated for s/mv-config/mv-common/ SATA port configs made board specific
changed IDe typo with IDE

Quoted 10 lines
 include/configs/guruplug.h        |  103 ++----------------
 include/configs/mv-common.h       |  225 
+++++++++++++++++++++++++++++++++++++
 include/configs/mv88f6281gtw_ge.h |  120 ++------------------
 include/configs/openrd_base.h     |  146 ++-----------------------
 include/configs/rd6281a.h         |  101 ++---------------
 include/configs/sheevaplug.h      |  104 +-----------------
 6 files changed, 266 insertions(+), 533 deletions(-)
 create mode 100644 include/configs/mv-common.h

Applied to u-boot-marvell.git master branch

Regards.
Prafulla . .

#4 lore raw

PATCH v2 3/3 Kirkwood: Changes specific to ARM relocation support

In reply to Prafulla Wadaskar

All Kirkwood based boards are supported for this new implementation
ref: docs/README.arm-relocation

---
Changelog:
v2: typo changed in the commit message
Security SRAM used for CONFIG_SYS_INIT_SP_ADDR

 include/configs/mv-common.h |    5 +++++
 1 files changed, 5 insertions(+), 0 deletions(-)
include/configs/mv-common.h +5 -0
index e78d29f..bdcebd3 100644
@@ -55,6 +55,11 @@
 #error "Unsupported SoC"
 #endif
 
+/* additions for new ARM relocation support */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+/* Kirkwood has 2k of Security SRAM, use it for SP */
+#define CONFIG_SYS_INIT_SP_ADDR		0xC8012000
+
 /*
  * CLKs configurations
  */
Signature · 1 line
1.5.3.3
#5 lore raw

PATCH v2 3/3 Kirkwood: Changes specific to ARM relocation support

Le 07/10/2010 16:58, Prafulla Wadaskar a ?crit :

Quoted 4 lines

All Kirkwood based boards are supported for this new implementation
ref: docs/README.arm-relocation

BTW, Wolfgang, is your offer to provide a branch to put ELF relocation related changes still valid? Even periodically rebased against master would be perfect... Otherwise I can set one up if you prefer.

Amicalement,

Signature · 1 line
Albert.
#6 lore raw

PATCH v2 3/3 Kirkwood: Changes specific to ARM relocation support

Dear Albert ARIBAUD,

Quoted 4 lines · In message <[email protected]> you wrote:

BTW, Wolfgang, is your offer to provide a branch to put ELF relocation related changes still valid? Even periodically rebased against master would be perfect... Otherwise I can set one up if you prefer.

Of course this is still valid, but

- I'm late with updating the u-boot-arm repo because I got stuck in this "little" task I started to make some progress with the Makefile / boards.cfg cleanup (that turned out to burn more time than expected)

- I lost a bit track of which exact version of the patches I should use. If you could please be so kind and send me a short reference to the current ones (messag-ID or similar).

Thanks.

Best regards,

Wolfgang Denk

Signature · 6 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"I find this a nice feature but it is not according to  the  documen-
tation. Or is it a BUG?"   "Let's call it an accidental feature. :-)"
                       - Larry Wall in <[email protected]>
#7 lore raw

PATCH v2 3/3 Kirkwood: Changes specific to ARM relocation support

Le 08/10/2010 10:32, Wolfgang Denk a ?crit :

Quoted 10 lines

Dear Albert ARIBAUD,

Quoted 4 lines · In message<[email protected]> you wrote:

BTW, Wolfgang, is your offer to provide a branch to put ELF relocation related changes still valid? Even periodically rebased against master would be perfect... Otherwise I can set one up if you prefer.

Of course this is still valid, but

Quoted 8 lines

- I'm late with updating the u-boot-arm repo because I got stuck in this "little" task I started to make some progress with the Makefile / boards.cfg cleanup (that turned out to burn more time than expected)

- I lost a bit track of which exact version of the patches I should use. If you could please be so kind and send me a short reference to the current ones (messag-ID or similar).

Actually I'd sent out a first [PATCH] set but have to do a couple of fixes based on comments to it; later today I'll send a [PATCH V2] version which I'll tag [ELF RELOC] to differenciate it from master patches.

Quoted 1 line

Thanks.

Thanks to you.

Quoted 3 lines

Best regards,

Wolfgang Denk

Amicalement,

Signature · 1 line
Albert.
#8 lore raw

PATCH v2 3/3 Kirkwood: Changes specific to ARM relocation support

In reply to Prafulla Wadaskar
Quoted 13 lines

-----Original Message-----
From: Prafulla Wadaskar [mailto:prafulla at marvell.com]
Sent: Thursday, October 07, 2010 8:29 PM
To: u-boot at lists.denx.de
Cc: Prabhanjan Sarnaik; Ashish Karkare; Prafulla Wadaskar
Subject: [PATCH V2 3/3] Kirkwood: Changes specific to ARM relocation support

All Kirkwood based boards are supported for this new implementation
ref: docs/README.arm-relocation

Quoted 9 lines

---
Changelog:
v2: typo changed in the commit message
Security SRAM used for CONFIG_SYS_INIT_SP_ADDR

 include/configs/mv-common.h |    5 +++++
 1 files changed, 5 insertions(+), 0 deletions(-)

Applied to u-boot-marvell.git master branch

Regards.
Prafulla . .