[RFC: WL1271 DC supprot on OMAP3EVM 0/5]
Subsystems (9)
cover [RFC: WL1271 DC supprot on OMAP3EVM 0/5]
From: Sanjay Kumar Champati <csanjay-EvXpCiN+lbve9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
Sanjay Kumar Champati (5):
ARM: Supported MMC 2 features for OMAP3EVM
ARM: Supported for Standard SDIO driver on OMAP3EVM for WL1271 DC
ARM: Supported for BT enable on OMAP3EVM for WL1271 DC
ARM: Added ALSA audio support for WL1271 DC over the PCM interface
(OMAP37XX)
Supported BT and WLAN configuration for WL1271 over the OMAP37XX
arch/arm/configs/omap3_evm_defconfig | 27 +++++++- arch/arm/mach-omap2/board-omap3evm.c | 28 ++++++++- arch/arm/mach-omap2/mmc-twl4030.c | 1 + arch/arm/mach-omap2/mmc-twl4030.h | 2 + drivers/bluetooth/Kconfig | 7 ++ drivers/char/tty_io.c | 110 ++++++++++++++++++++++++++++++++++ drivers/mmc/core/sdio_ops.c | 7 ++- drivers/net/wireless/Kconfig | 11 ++++ sound/soc/omap/Kconfig | 6 ++ sound/soc/omap/Makefile | 2 + sound/soc/omap/omap3evm.c | 81 ++++++++++++++++++++++++- sound/soc/omap/wl1271bt.c | 59 ++++++++++++++++++ sound/soc/omap/wl1271bt.h | 16 +++++ 13 files changed, 350 insertions(+), 7 deletions(-) create mode 100644 sound/soc/omap/wl1271bt.c create mode 100644 sound/soc/omap/wl1271bt.h
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
A message that is not in the archive (sent off-list or not yet received): 1286967439-705-1-git-send-email-csanjay-EvXpCiN+lbve9wHmmfpqLFaTQe2KTcn/@public.gmane.org
RFC 2/5 ARM: Supported for Standard SDIO driver on OMAP3EVM for WL1271 DC
From: Sanjay Kumar Champati <csanjay-EvXpCiN+lbve9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
* Apply MMC2 support patch before apply this patch
* Modified the "Kconfig" and "board-omap3evm.c" files to support standard SDIO driver for WL1271 DC
--- arch/arm/mach-omap2/board-omap3evm.c | 13 ++++++++++++- drivers/mmc/core/sdio_ops.c | 7 ++++++- drivers/net/wireless/Kconfig | 11 +++++++++++ 3 files changed, 29 insertions(+), 2 deletions(-)
arch/arm/mach-omap2/board-omap3evm.c +12 -1
@@ -79,6 +79,10 @@#define OMAP3EVM_ETHR_ID_REV 0x50#define OMAP3EVM_ETHR_GPIO_IRQ 176#define OMAP3EVM_SMSC911X_CS 5 +#ifdef CONFIG_WL1271_WLAN +#define OMAP3EVM_WLAN_EN 150 +#define OMAP3EVM_WLAN_IRQ 149 +#endif extern struct regulator_consumer_supply twl4030_vmmc1_supply;extern struct regulator_consumer_supply twl4030_vsim_supply;
@@ -749,7 +753,14 @@ static int omap3evm_twl_gpio_setup(struct device *dev, twl4030_vmmc1_supply.dev = mmc[0 ].dev; twl4030_vsim_supply.dev = mmc[0 ].dev; twl4030_vmmc2_supply.dev = mmc[1 ].dev; - +#ifdef CONFIG_WL1271_WLAN +omap_mux_init_gpio (OMAP3EVM_WLAN_EN ,OMAP_PIN_OUTPUT ); +if (gpio_request (OMAP3EVM_WLAN_EN ,"WLAN_ENABLE" )) +printk (KERN_ERR "Fail to get WLAN Enable GPIO\n" ); +gpio_direction_output (OMAP3EVM_WLAN_EN ,1 ); +mdelay (100 ); +omap_mux_init_gpio (OMAP3EVM_WLAN_IRQ ,OMAP_PIN_INPUT ); +#endif /* * Most GPIOs are for USB OTG. Some are mostly sent to * the P2 connector; notably LEDA for the LCD backlight.
drivers/mmc/core/sdio_ops.c +6 -1
@@ -114,6 +114,9 @@ int mmc_io_rw_direct(struct mmc_card *card, int write, unsigned fn,return 0 ; } +#ifdef CONFIG_WL1271_WLAN +EXPORT_SYMBOL (mmc_io_rw_direct); +#endif int mmc_io_rw_extended (struct mmc_card *card,int write,unsigned fn,unsigned addr,int incr_addr,u8 *buf,unsigned blocks,unsigned blksz)
@@ -181,4 +184,6 @@ int mmc_io_rw_extended(struct mmc_card *card, int write, unsigned fn,return 0 ; } - +#ifdef CONFIG_WL1271_WLAN +EXPORT_SYMBOL (mmc_io_rw_extended); +#endif
drivers/net/wireless/Kconfig +11 -0
@@ -31,6 +31,17 @@ config PCMCIA_RAYCS To compile this driver as a module, choose M here: the module will be called ray_cs. If unsure, say N. +config WL1271_WLAN + tristate "WL1271 TI's SDIO based wireless card" + select WIRELESS_EXT + select CRYPTO + select WEXT_SPY + select WEXT_PRIV + ---help--- + This driver support both the standard Linux Wireless Extensions + and TI's proprietary API, so both the Linux Wireless Tools and this + module support 2.4 GHz 802.11 b/g/n standrd. + config LIBERTAS_THINFIRM tristate "Marvell 8xxx Libertas WLAN driver support with thin firmware" depends on MAC80211
Signature · 6 lines
1.6.3.3 -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
A message that is not in the archive (sent off-list or not yet received): 1286967439-705-3-git-send-email-csanjay-EvXpCiN+lbve9wHmmfpqLFaTQe2KTcn/@public.gmane.org
RE: [RFC: WL1271 DC supprot on OMAP3EVM 2/5] ARM: Supported for Standard SDIO driver on OMAP3EVM for WL1271 DC
Quoted 42 lines
-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of csanjay-EvXpCiN+lbve9wHmmfpqLFaTQe2KTcn/@public.gmane.org
Sent: Wednesday, October 13, 2010 4:27 PM
To: [email protected]
Cc: [email protected]; Sanjay Kumar Champati
Subject: [RFC: WL1271 DC supprot on OMAP3EVM 2/5] ARM:
Supported for Standard SDIO driver on OMAP3EVM for WL1271 DCFrom: Sanjay Kumar Champati <csanjay-EvXpCiN+lbve9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
* Apply MMC2 support patch before apply this patch
* Modified the "Kconfig" and "board-omap3evm.c" files to support standard SDIO driver for WL1271 DC--- arch/arm/mach-omap2/board-omap3evm.c | 13 ++++++++++++- drivers/mmc/core/sdio_ops.c | 7 ++++++- drivers/net/wireless/Kconfig | 11 +++++++++++ 3 files changed, 29 insertions(+), 2 deletions(-)arch/arm/mach-omap2/board-omap3evm.c +4
-0@@ -79,6 +79,10 @@#define OMAP3EVM_ETHR_ID_REV 0x50#define OMAP3EVM_ETHR_GPIO_IRQ 176#define OMAP3EVM_SMSC911X_CS 5 +#ifdef CONFIG_WL1271_WLAN +#define OMAP3EVM_WLAN_EN 150 +#define OMAP3EVM_WLAN_IRQ 149 +#endif extern struct regulator_consumer_supply twl4030_vmmc1_supply;extern struct regulator_consumer_supply twl4030_vsim_supply;
arch/arm/mach-omap2/board-omap3evm.c static int · line 758
Quoted 7 lines
arch/arm/mach-omap2/board-omap3evm.c +2
-1@@ -749,7 +753,14 @@ static int omap3evm_twl_gpio_setup(struct device *dev, twl4030_vmmc1_supply.dev = mmc[0].dev; twl4030_vsim_supply.dev = mmc[0 ].dev; twl4030_vmmc2_supply.dev = mmc[1 ].dev; - +#ifdef CONFIG_WL1271_WLAN +omap_mux_init_gpio (OMAP3EVM_WLAN_EN ,OMAP_PIN_OUTPUT );
Check for return value
arch/arm/mach-omap2/board-omap3evm.c static int omap3evm_twl_gpio_setup(struct device *dev, · line 761
Quoted 4 lines
arch/arm/mach-omap2/board-omap3evm.c +4
-0+if (gpio_request (OMAP3EVM_WLAN_EN ,"WLAN_ENABLE" )) +printk (KERN_ERR "Fail to get WLAN Enable GPIO\n" ); +gpio_direction_output (OMAP3EVM_WLAN_EN ,1 ); +mdelay (100 );
You may add a comment to mention why this needs to be 100.
arch/arm/mach-omap2/board-omap3evm.c static int omap3evm_twl_gpio_setup(struct device *dev, · line 762
Quoted 1 line
arch/arm/mach-omap2/board-omap3evm.c +1
-0+omap_mux_init_gpio (OMAP3EVM_WLAN_IRQ ,OMAP_PIN_INPUT );
Check for return value
Quoted 53 lines
arch/arm/mach-omap2/board-omap3evm.c +1
-0+#endif /* * Most GPIOs are for USB OTG. Some are mostly sent to arch/arm/mach-omap2/board-omap3evm.c +0
-0* the P2 connector; notably LEDA for the LCD backlight. drivers/mmc/core/sdio_ops.c +3
-0@@ -114,6 +114,9 @@ int mmc_io_rw_direct(struct mmc_card *card, int write, unsigned fn, return 0; } +#ifdef CONFIG_WL1271_WLAN +EXPORT_SYMBOL (mmc_io_rw_direct); +#endif int mmc_io_rw_extended(struct mmc_card *card, int write, unsigned fn,unsigned addr, int
incr_addr, u8 *buf, unsigned blocks,
unsigned blksz)drivers/mmc/core/sdio_ops.c +3
-1@@ -181,4 +184,6 @@ int mmc_io_rw_extended(struct mmc_card *card, int write, unsigned fn, return 0; } - +#ifdef CONFIG_WL1271_WLAN +EXPORT_SYMBOL (mmc_io_rw_extended); +#endif drivers/net/wireless/Kconfig +0
-0@@ -31,6 +31,17 @@ config PCMCIA_RAYCS To compile this driver as a module, choose M here:the module will be
drivers/net/wireless/Kconfig +9
-0called ray_cs. If unsure, say N. +config WL1271_WLAN + tristate "WL1271 TI's SDIO based wireless card" + select WIRELESS_EXT + select CRYPTO + select WEXT_SPY + select WEXT_PRIV + ---help--- + This driver support both the standard Linux Wireless Extensions + and TI's proprietary API, so both the Linux WirelessTools and this
drivers/net/wireless/Kconfig +2
-0+ module support 2.4 GHz 802.11 b/g/n standrd. + config LIBERTAS_THINFIRM tristate "Marvell 8xxx Libertas WLAN driver support
Quoted 4 lines
with thin firmware"
depends on MAC80211Signature · 1 line
1.6.3.3
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [RFC: WL1271 DC supprot on OMAP3EVM 2/5] ARM: Supported for Standard SDIO driver on OMAP3EVM for WL1271 DC
In reply to a message not in the archivedrivers/net/wireless/Kconfig config PCMCIA_RAYCS · line 43
Quoted 10 lines · On Wed, 2010-10-13 at 16:27 +0530, csanjay-EvXpCiN+lbve9wHmmfpqLFaTQe2KTcn/@pub…
drivers/net/wireless/Kconfig +10
-0+config WL1271_WLAN + tristate "WL1271 TI's SDIO based wireless card" + select WIRELESS_EXT + select CRYPTO + select WEXT_SPY + select WEXT_PRIV + ---help--- + This driver support both the standard Linux Wireless Extensions + and TI's proprietary API, so both the Linux Wireless Tools and this + module support 2.4 GHz 802.11 b/g/n standrd.
Err, no? For once, you aren't actually adding a driver, and secondly, you don't get to add drivers that need WIRELESS_EXT or any of the other wext crap outside staging.
johannes
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
RFC 3/5 ARM: Supported for BT enable on OMAP3EVM for WL1271 DC
In reply to a message not in the archiveFrom: Sanjay Kumar Champati <csanjay-EvXpCiN+lbve9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
* Midified "tty_io.c" and "Kconfig" files to suuport BT enable for WL1271
--- drivers/bluetooth/Kconfig | 7 +++ drivers/char/tty_io.c | 110 +++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 117 insertions(+), 0 deletions(-)
drivers/bluetooth/Kconfig +7 -0
@@ -195,5 +195,12 @@ config BT_MRVL_SDIO Say Y here to compile support for Marvell BT-over-SDIO driver into the kernel or say M to compile it as module. +config BT_WL1271 + bool "WL1271 Bluetooth driver support" + depends on BT_HCIUART + help + The core driver to support WL1271 Bluetooth devices. + Say Y here to compile WL1271 Bluetooth driver into the kernel. + endmenu
drivers/char/tty_io.c +110 -0
134 lines not on this page · raw message
Signature · 6 lines
1.6.3.3 -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
RFC 4/5 ARM: Added ALSA audio support for WL1271 DC over the PCM interface (OMAP37XX)
In reply to a message not in the archiveFrom: Sanjay Kumar Champati <csanjay-EvXpCiN+lbve9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
* Add "wl1271bt.c" & "wl1271bt.h" in the PS kernel to support PCM interface for OMAP37XX
* Modified "Makefile" file to compile "wl1271bt.c" & "wl1271bt.h" files
* Modified "omap3evm.c" file to support Audio codec for WL1271 DC
--- sound/soc/omap/Kconfig | 6 +++ sound/soc/omap/Makefile | 2 + sound/soc/omap/omap3evm.c | 81 +++++++++++++++++++++++++++++++++++++++++++- sound/soc/omap/wl1271bt.c | 59 ++++++++++++++++++++++++++++++++ sound/soc/omap/wl1271bt.h | 16 +++++++++ 5 files changed, 162 insertions(+), 2 deletions(-) create mode 100644 sound/soc/omap/wl1271bt.c create mode 100644 sound/soc/omap/wl1271bt.h
sound/soc/omap/Kconfig +6 -0
@@ -116,3 +116,9 @@ config SND_OMAP_SOC_IGEP0020 select SND_SOC_TWL4030 help Say Y if you want to add support for Soc audio on IGEP v2 board. + +config SND_OMAP_SOC_WL1271BT + tristate "WL1271 Bluetooth Codec support" + default n + help + Say Y if you want to add support for WL1271 on OMAP3EVM board.
sound/soc/omap/Makefile +2 -0
@@ -18,6 +18,7 @@ snd-soc-omap3pandora-objs := omap3pandora.o snd-soc-omap3beagle-objs := omap3beagle.o snd-soc-zoom2-objs := zoom2.o snd-soc-igep0020-objs := igep0020.o +snd-soc-wl1271bt-objs := wl1271bt.o obj-$(CONFIG_SND_OMAP_SOC_N810) += snd-soc-n810.o obj-$(CONFIG_SND_OMAP_SOC_AMS_DELTA) += snd-soc-ams-delta.o
@@ -31,3 +32,4 @@ obj-$(CONFIG_SND_OMAP_SOC_OMAP3_PANDORA) += snd-soc-omap3pandora.o obj-$(CONFIG_SND_OMAP_SOC_OMAP3_BEAGLE) += snd-soc-omap3beagle.o obj-$(CONFIG_SND_OMAP_SOC_ZOOM2) += snd-soc-zoom2.o obj-$(CONFIG_SND_OMAP_SOC_IGEP0020) += snd-soc-igep0020.o +obj-$(CONFIG_SND_OMAP_SOC_WL1271BT) += snd-soc-wl1271bt.o
sound/soc/omap/omap3evm.c +79 -2
125 lines not on this page · raw message
sound/soc/omap/wl1271bt.c new file +59 -0
59 lines not on this page · raw message
sound/soc/omap/wl1271bt.h new file +16 -0
@@ -0,0 +1,16 @@ +/* +* wl1271bt.h -- ALSA SoC WL1271 Bluetooth codec driver header +* +* Author: Sinoj M. Issac, <sinoj at mistralsolutions.com> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +*/ + +#ifndef WL1271BT_H +#define WL1271BT_H + +extern struct snd_soc_dai wl1271bt_dai; + +#endif /* WL1271BT_H */
Signature · 6 lines
1.6.3.3 -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Sanjay,
Quoted 10 lines · On Wed, 2010-10-13 at 12:57 +0200, ext csanjay-EvXpCiN+lbve9wHmmfpqLFaTQe2KTcn/…
From: Sanjay Kumar Champati <csanjay-EvXpCiN+lbve9wHmmfpqLFaTQe2KTcn/@public.gmane.org>
Sanjay Kumar Champati (5):
ARM: Supported MMC 2 features for OMAP3EVM
ARM: Supported for Standard SDIO driver on OMAP3EVM for WL1271 DC
ARM: Supported for BT enable on OMAP3EVM for WL1271 DC
ARM: Added ALSA audio support for WL1271 DC over the PCM interface(OMAP37XX)Supported BT and WLAN configuration for WL1271 over the OMAP37XX
Nobody (or at least most of us) don't even understand what exactly the purpose of your patchset it. Can you try to explain what you're trying to achieve?
Also, you should clean things up, put platform-specific things where they belong etc. You really must review your implementation from an architectural point of view. If you have questions, ask here first. In most cases a patch describes things better than a thousand words, but it is certainly not the case here. ;)
Signature · 7 lines
Cheers, Luca. -- To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
RFC 1/5 ARM: Supported MMC 2 features for OMAP3EVM
In reply to csanjay-EvXpCiN+lbve9wHmmfpqLFaTQe2KTcn/@public.gmane.orgFrom: Sanjay Kumar Champati <[email protected]>
* Modified "board-omap3evm.c" file for MMC2 support
* Modified "mmc-twl4030.c" and "mmc-twl4030.h" file for MMC2 power support
--- arch/arm/mach-omap2/board-omap3evm.c | 15 +++++++++++++++ arch/arm/mach-omap2/mmc-twl4030.c | 1 + arch/arm/mach-omap2/mmc-twl4030.h | 2 ++ 3 files changed, 18 insertions(+), 0 deletions(-)
arch/arm/mach-omap2/board-omap3evm.c +15 -0
@@ -611,6 +611,13 @@ static struct twl4030_hsmmc_info mmc[] = { .gpio_cd = -EINVAL, .gpio_wp = 63, }, + { + .mmc = 2, + .wires = 4, + .gpio_cd = -EINVAL, + .gpio_wp = -EINVAL, + .ocr_mask = 0x00000080, + }, {}/* Terminator */ };
@@ -741,6 +748,7 @@ static int omap3evm_twl_gpio_setup(struct device *dev,/* link regulators to MMC adapters */ twl4030_vmmc1_supply.dev = mmc[0 ].dev; twl4030_vsim_supply.dev = mmc[0 ].dev; + twl4030_vmmc2_supply.dev = mmc[1 ].dev;/* * Most GPIOs are for USB OTG. Some are mostly sent to
@@ -949,6 +957,7 @@ static int __init omap3_evm_i2c_init(void)*/ omap3evm_twldata.vmmc1 = &vmmc1_data; omap3evm_twldata.vsim = &vsim_data; + omap3evm_twldata.vmmc2 = &vmmc2_data;omap_register_i2c_bus (1 ,2600 , omap3evm_i2c_boardinfo,ARRAY_SIZE (omap3evm_i2c_boardinfo));
@@ -1067,6 +1076,12 @@ static struct omap_board_mux omap35x_board_mux[] __initdata = {OMAP_PIN_OFF_INPUT_PULLUP |OMAP_PIN_OFF_OUTPUT_LOW | OMAP_PIN_OFF_WAKEUPENABLE), #endif +OMAP3_MUX (SDMMC2_CLK ,OMAP_MUX_MODE0 |OMAP_PIN_INPUT_PULLUP ), +OMAP3_MUX (SDMMC2_CMD ,OMAP_MUX_MODE0 |OMAP_PIN_INPUT_PULLUP ), +OMAP3_MUX (SDMMC2_DAT0 ,OMAP_MUX_MODE0 |OMAP_PIN_INPUT_PULLUP ), +OMAP3_MUX (SDMMC2_DAT1 ,OMAP_MUX_MODE0 |OMAP_PIN_INPUT_PULLUP ), +OMAP3_MUX (SDMMC2_DAT2 ,OMAP_MUX_MODE0 |OMAP_PIN_INPUT_PULLUP ), +OMAP3_MUX (SDMMC2_DAT3 ,OMAP_MUX_MODE0 |OMAP_PIN_INPUT_PULLUP ), { .reg_offset = OMAP_MUX_TERMINATOR }, };
arch/arm/mach-omap2/mmc-twl4030.c +1 -0
@@ -124,6 +124,7 @@ static int twl_mmc_late_init(struct device *dev) } hsmmc[i].vcc = reg; mmc->slots[0 ].ocr_mask =mmc_regulator_get_ocrmask (reg); + mmc->slots[1 ].ocr_mask =mmc_regulator_get_ocrmask (reg);/* allow an aux regulator */ reg =regulator_get (dev,"vmmc_aux" );
arch/arm/mach-omap2/mmc-twl4030.h +2 -0
@@ -34,3 +34,5 @@ static inline void twl4030_mmc_init(struct twl4030_hsmmc_info *info) }#endif +extern struct regulator_consumer_supply twl4030_vmmc2_supply; +extern struct regulator_init_data vmmc2_data;
Signature · 1 line
1.6.3.3
RFC 5/5 Supported BT and WLAN configuration for WL1271 over the OMAP37XX
In reply to csanjay-EvXpCiN+lbve9wHmmfpqLFaTQe2KTcn/@public.gmane.orgFrom: Sanjay Kumar Champati <[email protected]>
* Modified the "omap3_evm_defconfig" file to support WLAN and BT configuration for WL1271
--- arch/arm/configs/omap3_evm_defconfig | 27 ++++++++++++++++++++++++--- 1 files changed, 24 insertions(+), 3 deletions(-)
arch/arm/configs/omap3_evm_defconfig +24 -3
@@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit # Linux kernel version: 2.6.32 -# Tue Jan 5 13:03:54 2010 +# Sun Oct 10 05:00:18 2010 # CONFIG_ARM=y CONFIG_SYS_SUPPORTS_APM_EMULATION=y
@@ -492,10 +492,29 @@ CONFIG_DEFAULT_TCP_CONG="cubic" # CONFIG_HAMRADIO is not set # CONFIG_CAN is not set # CONFIG_IRDA is not set -# CONFIG_BT is not set +CONFIG_BT=y +CONFIG_BT_L2CAP=y +CONFIG_BT_SCO=y +CONFIG_BT_RFCOMM=y +CONFIG_BT_RFCOMM_TTY=y + +# +# Bluetooth device drivers +# +CONFIG_BT_HCIUART=y +CONFIG_BT_HCIUART_H4=y +CONFIG_BT_HCIUART_BCSP=y +CONFIG_BT_HCIUART_LL=y +CONFIG_BT_WL1271=y # CONFIG_AF_RXRPC is not set CONFIG_WIRELESS=y +CONFIG_WIRELESS_EXT=y +CONFIG_WEXT_CORE=y +CONFIG_WEXT_PROC=y +CONFIG_WEXT_SPY=y +CONFIG_WEXT_PRIV=y # CONFIG_CFG80211 is not set +CONFIG_WIRELESS_EXT_SYSFS=y # CONFIG_LIB80211 is not set #
@@ -740,6 +759,7 @@ CONFIG_SMSC911X=y # CONFIG_NETDEV_1000 is not set # CONFIG_NETDEV_10000 is not set CONFIG_WLAN=y +CONFIG_WL1271_WLAN=y # CONFIG_USB_ZD1201 is not set # CONFIG_HOSTAP is not set
@@ -1302,6 +1322,7 @@ CONFIG_SND_SOC=y CONFIG_SND_OMAP_SOC=y CONFIG_SND_OMAP_SOC_MCBSP=y CONFIG_SND_OMAP_SOC_OMAP3EVM=y +CONFIG_SND_OMAP_SOC_WL1271BT=y CONFIG_SND_SOC_I2C_AND_SPI=y # CONFIG_SND_SOC_ALL_CODECS is not set CONFIG_SND_SOC_TWL4030=y
@@ -2004,7 +2025,7 @@ CONFIG_CRYPTO_HW=y CONFIG_BITREVERSE=y CONFIG_GENERIC_FIND_LAST_BIT=y CONFIG_CRC_CCITT=y -# CONFIG_CRC16 is not set +CONFIG_CRC16=y # CONFIG_CRC_T10DIF is not set # CONFIG_CRC_ITU_T is not set CONFIG_CRC32=y
Signature · 1 line
1.6.3.3
Hi Sanjay,
Quoted 7 lines · On Wed, Oct 13, 2010 at 12:57 PM, <[email protected]> wrote:
Sanjay Kumar Champati (5):
ARM: Supported MMC 2 features for OMAP3EVM
ARM: Supported for Standard SDIO driver on OMAP3EVM for WL1271 DC
ARM: Supported for BT enable on OMAP3EVM for WL1271 DC
ARM: Added ALSA audio support for WL1271 DC over the PCM interface (OMAP37XX)
Supported BT and WLAN configuration for WL1271 over the OMAP37XX
There are many things to say here but maybe the most important one is that it seems you are trying to push changes that are only relevant for an out-of-tree driver, and such changes will never be accepted.
Why don't you try out the mainline wl1271 driver on your board and come back with the necessary changes for that ?
Thanks,
Ohad.
Quoted 15 lines
arch/arm/configs/omap3_evm_defconfig | 27 +++++++-
arch/arm/mach-omap2/board-omap3evm.c| 28 ++++++++-arch/arm/mach-omap2/mmc-twl4030.c| 1 +arch/arm/mach-omap2/mmc-twl4030.h| 2 +drivers/bluetooth/Kconfig| 7 ++drivers/char/tty_io.c| 110 ++++++++++++++++++++++++++++++++++drivers/mmc/core/sdio_ops.c| 7 ++-drivers/net/wireless/Kconfig| 11 ++++sound/soc/omap/Kconfig| 6 ++sound/soc/omap/Makefile| 2 +sound/soc/omap/omap3evm.c | 81 ++++++++++++++++++++++++- sound/soc/omap/wl1271bt.c | 59 ++++++++++++++++++ sound/soc/omap/wl1271bt.h | 16 +++++ 13 files changed, 350 insertions(+), 7 deletions(-)
Quoted 8 lines
create mode 100644
sound/soc/omap/wl1271bt.c
create mode 100644sound/soc/omap/wl1271bt.h--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html