tnetv107x ssp driver stack
Subsystems (9)
v2 cover tnetv107x ssp driver stack
TI's sequencer serial port (TI-SSP) is a jack-of-all-trades type of serial port device. It has a built-in programmable execution engine that can be programmed to operate as almost any serial bus (I2C, SPI, EasyScale, and others).
This patch series implements a driver stack that looks like the following:
+--------+
| eeprom | . . .
+--------+
+-----------+ +--------------+ +---------+
| regulator | . . . | i2c-gpio | | 1-wire | . . .
+-----------+ +--------------+ +---------+
+----------------------+ +--------------------------------+
| ssp-spi | | ssp-gpio |
+----------------------+ +--------------------------------+
+----------------------------------------------------------+
| ssp |
+----------------------------------------------------------+Changes between v1 and v2 of this series:
- Replaced open()/close() semantics with dynamic platform_device registration on SSP probe.
- Removed user-land interface to regulator registers
- More sensible regulator constraints
- Other minor cleanups
Cyril Chemparathy (12):
misc: add driver for sequencer serial port
davinci: add tnetv107x ssp platform device
davinci: add ssp config for tnetv107x evm board
spi: add ti-ssp spi master driver
davinci: add spi devices on tnetv107x evm
regulator: add driver for tps6524x regulator
davinci: add tnetv107x evm regulators
gpio: add ti-ssp virtual gpio driver
davinci: add tnetv107x evm ti-ssp gpio device
backlight: add support for tps6116x controller
davinci: add tnetv107x evm backlight device
davinci: add tnetv107x evm i2c eeprom device
arch/arm/mach-davinci/board-tnetv107x-evm.c | 199 +++++++ arch/arm/mach-davinci/devices-tnetv107x.c | 25 + arch/arm/mach-davinci/include/mach/ti_ssp.h | 99 ++++ arch/arm/mach-davinci/include/mach/tnetv107x.h | 2 + arch/arm/mach-davinci/tnetv107x.c | 2 +- drivers/gpio/Kconfig | 10 + drivers/gpio/Makefile | 1 + drivers/gpio/ti-ssp-gpio.c | 200 +++++++ drivers/misc/Kconfig | 11 + drivers/misc/Makefile | 1 + drivers/misc/ti_ssp.c | 436 +++++++++++++++ drivers/regulator/Kconfig | 10 + drivers/regulator/Makefile | 1 + drivers/regulator/tps6524x-regulator.c | 692 ++++++++++++++++++++++++ drivers/spi/Kconfig | 6 + drivers/spi/Makefile | 1 + drivers/spi/spi_ti_ssp.c | 397 ++++++++++++++ drivers/video/backlight/Kconfig | 7 + drivers/video/backlight/Makefile | 2 +- drivers/video/backlight/tps6116x.c | 340 ++++++++++++ 20 files changed, 2440 insertions(+), 2 deletions(-) create mode 100644 arch/arm/mach-davinci/include/mach/ti_ssp.h create mode 100644 drivers/gpio/ti-ssp-gpio.c create mode 100644 drivers/misc/ti_ssp.c create mode 100644 drivers/regulator/tps6524x-regulator.c create mode 100644 drivers/spi/spi_ti_ssp.c create mode 100644 drivers/video/backlight/tps6116x.c
A message that is not in the archive (sent off-list or not yet received): 1287429922-18870-1-git-send-email-cyril-l0cyMroinI0@public.gmane.org
PATCH v2 1/12 misc: add driver for sequencer serial port
TI's sequencer serial port (TI-SSP) is a jack-of-all-trades type of serial port device. It has a built-in programmable execution engine that can be programmed to operate as almost any serial bus (I2C, SPI, EasyScale, and others).
This patch adds a driver for this controller device. The driver does not expose a user-land interface. Protocol drivers built on top of this layer are expected to remain in-kernel.
--- arch/arm/mach-davinci/include/mach/ti_ssp.h | 89 ++++++ drivers/misc/Kconfig | 11 + drivers/misc/Makefile | 1 + drivers/misc/ti_ssp.c | 436 +++++++++++++++++++++++++++ 4 files changed, 537 insertions(+), 0 deletions(-) create mode 100644 arch/arm/mach-davinci/include/mach/ti_ssp.h create mode 100644 drivers/misc/ti_ssp.c
arch/arm/mach-davinci/include/mach/ti_ssp.h new file +89 -0
@@ -0,0 +1,89 @@ +/* +* Sequencer Serial Port (SSP) driver for Texas Instruments' SoCs +* +* Copyright (C) 2010 Texas Instruments Inc +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2 of the License, or +* (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA +*/ + +#ifndef __TI_SSP_H__ +#define __TI_SSP_H__ + +struct ti_ssp_dev_data { +const char *dev_name; +unsigned long iosel;/* see note below */ +unsigned long config; +const void *pdata; +int pdata_sz; +}; + +struct ti_ssp_data { +unsigned long out_clock; +struct ti_ssp_dev_data dev_data[2 ]; +}; + +/* +* Sequencer port IO pin configuration bits. These do not correlate 1-1 with +* the hardware. The iosel field in the port data combines iosel1 and iosel2, +* and is therefore not a direct map to register space. It is best to use the +* macros below to construct iosel values. +* +* least significant 16 bits --> iosel1 +* most significant 16 bits --> iosel2 +*/ + +#define SSP_IN 0x0000 +#define SSP_DATA 0x0001 +#define SSP_CLOCK 0x0002 +#define SSP_CHIPSEL 0x0003 +#define SSP_OUT 0x0004 +#define SSP_PIN_SEL (pin, v) ((v) << ((pin) * 3)) +#define SSP_PIN_MASK (pin) SSP_PIN_SEL(pin, 0x7) +#define SSP_INPUT_SEL (pin) ((pin) << 16) + +/* Sequencer port config bits */ +#define SSP_EARLY_DIN BIT(8) +#define SSP_DELAY_DOUT BIT(9) + +/* Sequence map definitions */ +#define SSP_CLK_HIGH BIT(0) +#define SSP_CLK_LOW 0 +#define SSP_DATA_HIGH BIT(1) +#define SSP_DATA_LOW 0 +#define SSP_CS_HIGH BIT(2) +#define SSP_CS_LOW 0 +#define SSP_OUT_MODE BIT(3) +#define SSP_IN_MODE 0 +#define SSP_DATA_REG BIT(4) +#define SSP_ADDR_REG 0 + +#define SSP_OPCODE_DIRECT ((0x0) << 5) +#define SSP_OPCODE_TOGGLE ((0x1) << 5) +#define SSP_OPCODE_SHIFT ((0x2) << 5) +#define SSP_OPCODE_BRANCH0 ((0x4) << 5) +#define SSP_OPCODE_BRANCH1 ((0x5) << 5) +#define SSP_OPCODE_BRANCH ((0x6) << 5) +#define SSP_OPCODE_STOP ((0x7) << 5) +#define SSP_BRANCH (addr) ((addr) << 8) +#define SSP_COUNT (cycles) ((cycles) << 8) + +int ti_ssp_raw_read (struct device *dev); +int ti_ssp_raw_write (struct device *dev,u32 val); +int ti_ssp_load (struct device *dev,int offs,u32 * prog,int len); +int ti_ssp_run (struct device *dev,u32 pc,u32 input,u32 *output); +int ti_ssp_set_mode (struct device *dev,int mode); +int ti_ssp_set_iosel (struct device *dev,u32 iosel); + +#endif /* __TI_SSP_H__ */
drivers/misc/Kconfig +11 -0
@@ -390,6 +390,17 @@ config BMP085 To compile this driver as a module, choose M here: the module will be called bmp085. +config TI_SSP + depends on ARCH_DAVINCI_TNETV107X + tristate "Sequencer Serial Port support" + default y + ---help--- + Say Y here if you want support for the Sequencer Serial Port + in a Texas Instruments TNETV107X SoC. + + To compile this driver as a module, choose M here: the + module will be called ti_ssp. + source "drivers/misc/c2port/Kconfig" source "drivers/misc/eeprom/Kconfig" source "drivers/misc/cb710/Kconfig"
drivers/misc/Makefile +1 -0
@@ -28,6 +28,7 @@ obj-$(CONFIG_SENSORS_TSL2550) += tsl2550.o obj-$(CONFIG_EP93XX_PWM) += ep93xx_pwm.o obj-$(CONFIG_DS1682) += ds1682.o obj-$(CONFIG_TI_DAC7512) += ti_dac7512.o +obj-$(CONFIG_TI_SSP) += ti_ssp.o obj-$(CONFIG_C2PORT) += c2port/ obj-$(CONFIG_IWMC3200TOP) += iwmc3200top/ obj-$(CONFIG_HMC6352) += hmc6352.o
drivers/misc/ti_ssp.c new file +436 -0
436 lines not on this page · raw message
Signature · 9 lines
1.7.0.4 ------------------------------------------------------------------------------ Download new Adobe(R) Flash(R) Builder(TM) 4 The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly Flex(R) Builder(TM)) enable the development of rich applications that run across multiple browsers and platforms. Download your free trials today! http://p.sf.net/sfu/adobe-dev2dev
A message that is not in the archive (sent off-list or not yet received): 1287429922-18870-2-git-send-email-cyril-l0cyMroinI0@public.gmane.org
Grant Likely
Acked-byRe: [PATCH v2 01/12] misc: add driver for sequencer serial port
Quoted 9 lines · Cyril Chemparathy
TI's sequencer serial port (TI-SSP) is a jack-of-all-trades type of serial port device. It has a built-in programmable execution engine that can be programmed to operate as almost any serial bus (I2C, SPI, EasyScale, and others).
This patch adds a driver for this controller device. The driver does not expose a user-land interface. Protocol drivers built on top of this layer are expected to remain in-kernel.
Signed-off-by Cyril Chemparathy <[email protected]>
I like this version much better.
PATCH v2 2/12 davinci: add tnetv107x ssp platform device
In reply to a message not in the archiveThis patch adds an SSP platform device definition for the tnetv107x soc family. The clock lookup entry has also been updated to match.
--- arch/arm/mach-davinci/devices-tnetv107x.c | 25 ++++++++++++++++++++++++ arch/arm/mach-davinci/include/mach/tnetv107x.h | 2 + arch/arm/mach-davinci/tnetv107x.c | 2 +- 3 files changed, 28 insertions(+), 1 deletions(-)
arch/arm/mach-davinci/devices-tnetv107x.c +25 -0
@@ -35,6 +35,7 @@#define TNETV107X_SDIO0_BASE 0x08088700#define TNETV107X_SDIO1_BASE 0x08088800#define TNETV107X_KEYPAD_BASE 0x08088a00 +#define TNETV107X_SSP_BASE 0x08088c00#define TNETV107X_ASYNC_EMIF_CNTRL_BASE 0x08200000#define TNETV107X_ASYNC_EMIF_DATA_CE0_BASE 0x30000000#define TNETV107X_ASYNC_EMIF_DATA_CE1_BASE 0x40000000
@@ -342,6 +343,25 @@ static struct platform_device tsc_device = { .resource = tsc_resources, }; +static struct resource ssp_resources[] = { + { + .start =TNETV107X_SSP_BASE , + .end =TNETV107X_SSP_BASE +0x1ff , + .flags =IORESOURCE_MEM , + }, + { + .start =IRQ_TNETV107X_SSP , + .flags =IORESOURCE_IRQ , + }, +}; + +static struct platform_device ssp_device = { + .name ="ti-ssp" , + .id =-1 , + .num_resources =ARRAY_SIZE (ssp_resources), + .resource = ssp_resources, +}; +void __init tnetv107x_devices_init (struct tnetv107x_device_info *info) {int i;
@@ -367,4 +387,9 @@ void __init tnetv107x_devices_init(struct tnetv107x_device_info *info) keypad_device.dev.platform_data = info->keypad_config;platform_device_register (&keypad_device); } + +if (info->ssp_config) { + ssp_device.dev.platform_data = info->ssp_config; +platform_device_register (&ssp_device); + } }
arch/arm/mach-davinci/include/mach/tnetv107x.h +2 -0
@@ -38,12 +38,14 @@#include <mach/mmc.h> #include <mach/nand.h> #include <mach/serial.h> +#include <mach/ti_ssp.h> struct tnetv107x_device_info {struct davinci_uart_config *serial_config;struct davinci_mmc_config *mmc_config[2 ];/* 2 controllers */ struct davinci_nand_pdata *nand_config[4 ];/* 4 chipsels */ struct matrix_keypad_platform_data *keypad_config; +struct ti_ssp_data *ssp_config; };extern struct platform_device tnetv107x_wdt_device;
arch/arm/mach-davinci/tnetv107x.c +1 -1
@@ -277,7 +277,7 @@ static struct clk_lookup clks[] = {CLK (NULL ,"timer1" , &clk_timer1),CLK ("tnetv107x_wdt.0" ,NULL , &clk_wdt_arm),CLK (NULL ,"clk_wdt_dsp" , &clk_wdt_dsp), -CLK ("ti-ssp.0" ,NULL , &clk_ssp), +CLK ("ti-ssp" ,NULL , &clk_ssp),CLK (NULL ,"clk_tdm0" , &clk_tdm0),CLK (NULL ,"clk_vlynq" , &clk_vlynq), CLK(NULL, "clk_mcdma", &clk_mcdma),
Signature · 9 lines
1.7.0.4 ------------------------------------------------------------------------------ Download new Adobe(R) Flash(R) Builder(TM) 4 The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly Flex(R) Builder(TM)) enable the development of rich applications that run across multiple browsers and platforms. Download your free trials today! http://p.sf.net/sfu/adobe-dev2dev
PATCH v2 3/12 davinci: add ssp config for tnetv107x evm board
In reply to a message not in the archiveThis patch adds SSP configuration and pin muxing info for tnetv107x evm boards.
--- arch/arm/mach-davinci/board-tnetv107x-evm.c | 15 +++++++++++++++ 1 files changed, 15 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +15 -0
@@ -33,6 +33,7 @@#include <mach/edma.h> #include <mach/mux.h> #include <mach/cp_intc.h> +#include <mach/ti_ssp.h> #include <mach/tnetv107x.h> #define EVM_MMC_WP_GPIO 21
@@ -99,6 +100,12 @@ static const short uart1_pins[] __initdata = {-1 }; +static const short ssp_pins[]__initdata = { +TNETV107X_SSP0_0 ,TNETV107X_SSP0_1 ,TNETV107X_SSP0_2 , +TNETV107X_SSP1_0 ,TNETV107X_SSP1_1 ,TNETV107X_SSP1_2 , +TNETV107X_SSP1_3 ,-1 +}; +static struct mtd_partition nand_partitions[] = {/* bootloader (U-Boot, etc) in first 12 sectors */ {
@@ -196,17 +203,25 @@ static struct matrix_keypad_platform_data keypad_config = { .no_autorepeat = 0, }; +static struct ti_ssp_data ssp_config = { + .out_clock =250 *1000 , + .dev_data = { + }, +}; +static struct tnetv107x_device_info evm_device_info__initconst = { .serial_config = &serial_config, .mmc_config[1 ] = &mmc_config,/* controller 1 */ .nand_config[0 ] = &nand_config,/* chip select 0 */ .keypad_config = &keypad_config, + .ssp_config = &ssp_config, };static __init void tnetv107x_evm_board_init (void ) {davinci_cfg_reg_list (sdio1_pins);davinci_cfg_reg_list (uart1_pins); +davinci_cfg_reg_list (ssp_pins);tnetv107x_devices_init (&evm_device_info); }
Signature · 9 lines
1.7.0.4 ------------------------------------------------------------------------------ Download new Adobe(R) Flash(R) Builder(TM) 4 The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly Flex(R) Builder(TM)) enable the development of rich applications that run across multiple browsers and platforms. Download your free trials today! http://p.sf.net/sfu/adobe-dev2dev
PATCH v2 4/12 spi: add ti-ssp spi master driver
In reply to a message not in the archiveThis patch adds an SPI master implementation that operates on top of an underlying TI-SSP port.
--- arch/arm/mach-davinci/include/mach/ti_ssp.h | 5 + drivers/spi/Kconfig | 7 + drivers/spi/Makefile | 1 + drivers/spi/spi_ti_ssp.c | 397 +++++++++++++++++++++++++++ 4 files changed, 410 insertions(+), 0 deletions(-) create mode 100644 drivers/spi/spi_ti_ssp.c
arch/arm/mach-davinci/include/mach/ti_ssp.h +5 -0
@@ -34,6 +34,11 @@ struct ti_ssp_data {struct ti_ssp_dev_data dev_data[2 ]; }; +struct ti_ssp_spi_data { +int num_cs; +void (*select)(int cs); +}; +/* * Sequencer port IO pin configuration bits. These do not correlate 1-1 with * the hardware. The iosel field in the port data combines iosel1 and iosel2,
drivers/spi/Kconfig +7 -0
@@ -298,6 +298,13 @@ config SPI_STMP3XXX help SPI driver for Freescale STMP37xx/378x SoC SSP interface +config SPI_TI_SSP + tristate "TI SSP Controller SPI Driver" + depends on SPI_MASTER && TI_SSP + help + This selects an SPI master implementation using a TI sequencer + serial port. + config SPI_TXX9 tristate "Toshiba TXx9 SPI controller" depends on GENERIC_GPIO && CPU_TX49XX
drivers/spi/Makefile +1 -0
@@ -40,6 +40,7 @@ obj-$(CONFIG_SPI_S3C24XX_GPIO) += spi_s3c24xx_gpio.o obj-$(CONFIG_SPI_S3C24XX) += spi_s3c24xx_hw.o obj-$(CONFIG_SPI_S3C64XX) += spi_s3c64xx.o obj-$(CONFIG_SPI_TXX9) += spi_txx9.o +obj-$(CONFIG_SPI_TI_SSP) += spi_ti_ssp.o obj-$(CONFIG_SPI_XILINX) += xilinx_spi.o obj-$(CONFIG_SPI_XILINX_OF) += xilinx_spi_of.o obj-$(CONFIG_SPI_XILINX_PLTFM) += xilinx_spi_pltfm.o
drivers/spi/spi_ti_ssp.c new file +397 -0
397 lines not on this page · raw message
Signature · 9 lines
1.7.0.4 ------------------------------------------------------------------------------ Download new Adobe(R) Flash(R) Builder(TM) 4 The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly Flex(R) Builder(TM)) enable the development of rich applications that run across multiple browsers and platforms. Download your free trials today! http://p.sf.net/sfu/adobe-dev2dev
A message that is not in the archive (sent off-list or not yet received): 1287429922-18870-5-git-send-email-cyril-l0cyMroinI0@public.gmane.org
Grant Likely
Acked-byRe: [PATCH v2 04/12] spi: add ti-ssp spi master driver
Quoted 11 lines · Cyril Chemparathy
This patch adds an SPI master implementation that operates on top of an underlying TI-SSP port.
Signed-off-by Cyril Chemparathy <[email protected]>--- arch/arm/mach-davinci/include/mach/ti_ssp.h | 5 + drivers/spi/Kconfig | 7 + drivers/spi/Makefile | 1 + drivers/spi/spi_ti_ssp.c | 397 +++++++++++++++++++++++++++ 4 files changed, 410 insertions(+), 0 deletions(-) create mode 100644 drivers/spi/spi_ti_ssp.c
Minor comments below, but otherwise:
This patch should be merged with the rest of the series. I don't think there is any point in me picking it up into the SPI tree.
arch/arm/mach-davinci/include/mach/ti_ssp.h struct ti_ssp_data { · line 40
Quoted 13 lines
arch/arm/mach-davinci/include/mach/ti_ssp.h +4
-0@@ -34,6 +34,11 @@ struct ti_ssp_data {struct ti_ssp_dev_data dev_data[2 ]; }; +struct ti_ssp_spi_data { +int num_cs; +void (*select)(int cs); +};
Hmmm. I really should look into standardizing the way spi busses handle slave selects. In particular, it would be valuable to have a stock method for the common case of simple gpios used for ss lines.
(Not a critique on this patch, just thinking out loud).
Quoted 9 lines
arch/arm/mach-davinci/include/mach/ti_ssp.h +1
-0+/* * Sequencer port IO pin configuration bits. These do not correlate 1-1 with * the hardware. The iosel field in the port data combines iosel1 and iosel2, drivers/spi/Kconfig +0
-0
drivers/spi/Kconfig config SPI_STMP3XXX · line 303
Quoted 6 lines
drivers/spi/Kconfig +3
-0@@ -298,6 +298,13 @@ config SPI_STMP3XXX help SPI driver for Freescale STMP37xx/378x SoC SSP interface +config SPI_TI_SSP + tristate "TI SSP Controller SPI Driver" + depends on SPI_MASTER && TI_SSP
This is already in the "if SPI_MASTER" block. Make it simply "depends on TI_SSP".
Quoted 12 lines
drivers/spi/Kconfig +4
-0+ help + This selects an SPI master implementation using a TI sequencer + serial port. + config SPI_TXX9 tristate "Toshiba TXx9 SPI controller" depends on GENERIC_GPIO && CPU_TX49XXdrivers/spi/Makefile +0
-0
drivers/spi/Makefile obj-$(CONFIG_SPI_S3C24XX_GPIO) += spi_s3c24xx_gpio.o · line 43
Quoted 4 lines
drivers/spi/Makefile +1
-0@@ -40,6 +40,7 @@ obj-$(CONFIG_SPI_S3C24XX_GPIO) += spi_s3c24xx_gpio.o obj-$(CONFIG_SPI_S3C24XX) += spi_s3c24xx_hw.o obj-$(CONFIG_SPI_S3C64XX) += spi_s3c64xx.o obj-$(CONFIG_SPI_TXX9) += spi_txx9.o +obj-$(CONFIG_SPI_TI_SSP) += spi_ti_ssp.o
Nit: Try to keep the list both a) in the same order as Kconfig, and b) in alphabetical order (I know the kernel list isn't very close to alphabetical, but try not to make it worse). :-)
Quoted 409 lines
drivers/spi/Makefile +0
-0obj-$(CONFIG_SPI_XILINX) += xilinx_spi.o obj-$(CONFIG_SPI_XILINX_OF) += xilinx_spi_of.o obj-$(CONFIG_SPI_XILINX_PLTFM) += xilinx_spi_pltfm.odrivers/spi/spi_ti_ssp.c new file +397
-0@@ -0,0 +1,397 @@ +/* +* Sequencer Serial Port (SSP) based SPI master driver +* +* Copyright (C) 2010 Texas Instruments Inc +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2 of the License, or +* (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA +*/ + +#include <linux/kernel.h> +#include <linux/err.h> +#include <linux/completion.h> +#include <linux/delay.h> +#include <linux/platform_device.h> +#include <linux/spi/spi.h> + +#include <mach/ti_ssp.h> + +#define MODE_BITS (SPI_CPHA | SPI_CPOL | SPI_CS_HIGH) + +struct ti_ssp_spi { +const struct ti_ssp_spi_data *pdata; +struct spi_master *master; +struct device *dev; +spinlock_t lock; +struct list_head msg_queue; +struct completion complete; +int shutdown:1 ; +struct workqueue_struct *workqueue; +struct work_struct work; +u8 mode, bpw; +int cs_active; +u32 pc_en, pc_dis, pc_wr, pc_rd; +}; + +static u32 do_read_data (struct ti_ssp_spi *hw) +{ +u32 ret; + +ti_ssp_run (hw->dev, hw->pc_rd,0 , &ret); +return ret; +} + +static void do_write_data (struct ti_ssp_spi *hw,u32 data) +{ +ti_ssp_run (hw->dev, hw->pc_wr, data << (32 - hw->bpw),NULL ); +} + +static int do_transfer (struct ti_ssp_spi *hw,struct spi_message *msg, +struct spi_transfer *t) +{ +int count; + +if (hw->bpw <=8 ) { +u8 *rx = t->rx_buf; +const u8 *tx = t->tx_buf; + +for (count =0 ; count < t->len; count +=1 ) { +if (t->tx_buf) +do_write_data (hw, *tx++); +if (t->rx_buf) + *rx++ =do_read_data (hw); + } + }else if (hw->bpw <=16 ) { +u16 *rx = t->rx_buf; +const u16 *tx = t->tx_buf; + +for (count =0 ; count < t->len; count +=2 ) { +if (t->tx_buf) +do_write_data (hw, *tx++); +if (t->rx_buf) + *rx++ =do_read_data (hw); + } + }else { +u32 *rx = t->rx_buf; +const u32 *tx = t->tx_buf; + +for (count =0 ; count < t->len; count +=4 ) { +if (t->tx_buf) +do_write_data (hw, *tx++); +if (t->rx_buf) + *rx++ =do_read_data (hw); + } + } + + msg->actual_length += count;/* bytes transferred */ + +dev_dbg (&msg->spi->dev,"xfer %s%s, %d bytes, %d bpw, count %d%s\n" , + t->tx_buf ?"tx" :"" , t->rx_buf ?"rx" :"" , t->len, + hw->bpw, count, (count < t->len) ?" (under)" :"" ); + +return (count < t->len) ? -EIO :0 ;/* left over data */ +} + +static void chip_select (struct ti_ssp_spi *hw,int cs_active) +{ + cs_active = !!cs_active; +if (cs_active == hw->cs_active) +return ; +ti_ssp_run (hw->dev, cs_active ? hw->pc_en : hw->pc_dis,0 ,NULL ); + hw->cs_active = cs_active; +} + +#define __SHIFT_OUT (bits) (SSP_OPCODE_SHIFT | SSP_OUT_MODE | \ + cs_en | clk | SSP_COUNT((bits) * 2 - 1)) +#define __SHIFT_IN (bits) (SSP_OPCODE_SHIFT | SSP_IN_MODE | \ + cs_en | clk | SSP_COUNT((bits) * 2 - 1)) + +static int setup_xfer (struct ti_ssp_spi *hw,u8 bpw,u8 mode) +{ +int error, idx =0 ; +u32 seqram[16 ]; +u32 cs_en, cs_dis, clk; +u32 topbits, botbits; + + mode &=MODE_BITS ; +if (mode == hw->mode && bpw == hw->bpw) +return 0 ; + + cs_en = (mode &SPI_CS_HIGH ) ?SSP_CS_HIGH :SSP_CS_LOW ; + cs_dis = (mode &SPI_CS_HIGH ) ?SSP_CS_LOW :SSP_CS_HIGH ; + clk = (mode &SPI_CPOL ) ?SSP_CLK_HIGH :SSP_CLK_LOW ; + +/* Construct instructions */ + +/* Disable Chip Select */ + hw->pc_dis = idx; + seqram[idx++] =SSP_OPCODE_DIRECT |SSP_OUT_MODE | cs_dis | clk; + seqram[idx++] =SSP_OPCODE_STOP |SSP_OUT_MODE | cs_dis | clk; + +/* Enable Chip Select */ + hw->pc_en = idx; + seqram[idx++] =SSP_OPCODE_DIRECT |SSP_OUT_MODE | cs_en | clk; + seqram[idx++] =SSP_OPCODE_STOP |SSP_OUT_MODE | cs_en | clk; + +/* Reads and writes need to be split for bpw > 16 */ + topbits = (bpw >16 ) ?16 : bpw; + botbits = bpw - topbits; + +/* Write */ + hw->pc_wr = idx; + seqram[idx++] =__SHIFT_OUT (topbits) |SSP_ADDR_REG ; +if (botbits) + seqram[idx++] =__SHIFT_OUT (botbits) |SSP_DATA_REG ; + seqram[idx++] =SSP_OPCODE_STOP |SSP_OUT_MODE | cs_en | clk; + +/* Read */ + hw->pc_rd = idx; +if (botbits) + seqram[idx++] =__SHIFT_IN (botbits) |SSP_ADDR_REG ; + seqram[idx++] =__SHIFT_IN (topbits) |SSP_DATA_REG ; + seqram[idx++] =SSP_OPCODE_STOP |SSP_OUT_MODE | cs_en | clk; + + error =ti_ssp_load (hw->dev,0 , seqram, idx); +if (error <0 ) +return error; + + error =ti_ssp_set_mode (hw->dev, ((mode &SPI_CPHA ) ? +0 :SSP_EARLY_DIN )); +if (error <0 ) +return error; + + hw->bpw = bpw; + hw->mode = mode; + +return error; +} + +static void ti_ssp_spi_work (struct work_struct *work) +{ + struct ti_ssp_spi *hw = container_of(work, struct ti_ssp_spi, work); + +spin_lock_irq (&hw->lock); + +while (!list_empty (&hw->msg_queue)) { +struct spi_message *m; +struct spi_device *spi; +struct spi_transfer *t =NULL ; +int status =0 ; + + m = container_of(hw->msg_queue.next, struct spi_message, + queue); + +list_del_init (&m->queue); + + spi = m->spi; + +if (hw->pdata->select) + hw->pdata->select (spi->chip_select); + +list_for_each_entry (t, &m->transfers, transfer_list) { +int bpw = spi->bits_per_word; +int xfer_status; + +if (t->bits_per_word) + bpw = t->bits_per_word; + +if (setup_xfer (hw, bpw, spi->mode) <0 ) +break ; + +chip_select (hw,1 ); + +spin_unlock_irq (&hw->lock); + + xfer_status =do_transfer (hw, m, t); +if (xfer_status <0 ) + status = xfer_status; + +if (t->delay_usecs) +udelay (t->delay_usecs); + +spin_lock_irq (&hw->lock); + +if (t->cs_change) +chip_select (hw,0 ); + } + +chip_select (hw,0 ); + m->status = status; + m->complete (m->context); + } + +if (hw->shutdown) +complete (&hw->complete); + +spin_unlock_irq (&hw->lock); +} + +static int ti_ssp_spi_setup (struct spi_device *spi) +{ +if (spi->bits_per_word >32 ) +return -EINVAL ; + +return 0 ; +} + +static int ti_ssp_spi_transfer (struct spi_device *spi,struct spi_message *m) +{ +struct ti_ssp_spi *hw; +struct spi_transfer *t; +unsigned long flags; +int error =0 ; + + m->actual_length =0 ; + m->status = -EINPROGRESS ; + + hw =spi_master_get_devdata (spi->master); + +if (list_empty (&m->transfers) || !m->complete) +return -EINVAL ; + +list_for_each_entry (t, &m->transfers, transfer_list) { +if (t->len && !(t->rx_buf || t->tx_buf)) { +dev_err (&spi->dev,"invalid xfer, no buffer\n" ); +return -EINVAL ; + } + +if (t->len && t->rx_buf && t->tx_buf) { +dev_err (&spi->dev,"invalid xfer, full duplex\n" ); +return -EINVAL ; + } + +if (t->bits_per_word >32 ) { +dev_err (&spi->dev,"invalid xfer width %d\n" , + t->bits_per_word); +return -EINVAL ; + } + } + +spin_lock_irqsave (&hw->lock, flags); +if (hw->shutdown) { + error = -ESHUTDOWN ; + goto error_unlock; + } +list_add_tail (&m->queue, &hw->msg_queue); +queue_work (hw->workqueue, &hw->work); +error_unlock: +spin_unlock_irqrestore (&hw->lock, flags); +return error; +} + +static int __devinit ti_ssp_spi_probe (struct platform_device *pdev) +{ +const struct ti_ssp_spi_data *pdata; +struct ti_ssp_spi *hw; +struct spi_master *master; +struct device *dev = &pdev->dev; +int error =0 ; + + pdata = dev->platform_data; +if (!pdata) { +dev_err (dev,"platform data not found\n" ); +return -EINVAL ; + } + + master =spi_alloc_master (dev,sizeof (struct ti_ssp_spi )); +if (!master) { +dev_err (dev,"cannot allocate SPI master\n" ); +return -ENOMEM ; + } + + hw =spi_master_get_devdata (master); +platform_set_drvdata (pdev, hw); + + hw->master = master; + hw->dev = dev; + hw->pdata = pdata; + +spin_lock_init (&hw->lock); +init_completion (&hw->complete); +INIT_LIST_HEAD (&hw->msg_queue); +INIT_WORK (&hw->work, ti_ssp_spi_work); + + hw->workqueue =create_singlethread_workqueue (dev_name (dev)); +if (!hw->workqueue) { + error = -ENOMEM ; +dev_err (dev,"work queue creation failed\n" ); + goto error_wq; + } + + master->bus_num = pdev->id; + master->num_chipselect = hw->pdata->num_cs; + master->mode_bits =MODE_BITS ; + master->flags =SPI_MASTER_HALF_DUPLEX ; + master->setup = ti_ssp_spi_setup; + master->transfer = ti_ssp_spi_transfer; + + error =spi_register_master (master); +if (error) { +dev_err (dev,"master registration failed\n" ); + goto error_reg; + } + +return 0 ; + +error_reg: +destroy_workqueue (hw->workqueue); +error_wq: +spi_master_put (master); +return error; +} + +static int __devexit ti_ssp_spi_remove(struct platform_device *pdev) +{ +struct ti_ssp_spi *hw =platform_get_drvdata (pdev); +int error; + + hw->shutdown =1 ; +while (!list_empty (&hw->msg_queue)) { + error =wait_for_completion_interruptible (&hw->complete); +if (error <0 ) { + hw->shutdown =0 ; +return error; + } + } +destroy_workqueue (hw->workqueue); +spi_unregister_master (hw->master); + +return 0 ; +} + +static struct platform_driver ti_ssp_spi_driver = { + .probe = ti_ssp_spi_probe, + .remove =__devexit_p (ti_ssp_spi_remove), + .driver = { + .name ="ti-ssp-spi" , + .owner =THIS_MODULE , + }, +}; + +static int __init ti_ssp_spi_init (void ) +{ +return platform_driver_register (&ti_ssp_spi_driver); +} +subsys_initcall (ti_ssp_spi_init); + +static void __exit ti_ssp_spi_exit(void) +{ +platform_driver_unregister (&ti_ssp_spi_driver); +} +module_exit (ti_ssp_spi_exit); + +MODULE_DESCRIPTION ("SSP SPI Master" ); +MODULE_AUTHOR ("Cyril Chemparathy" ); +MODULE_LICENSE ("GPL" ); +MODULE_ALIAS ("platform:spi_ti_ssp" );Signature · 1 line
1.7.0.4
PATCH v2 5/12 davinci: add spi devices on tnetv107x evm
In reply to a message not in the archiveThis patch adds definitions for spi devices on the tnetv107x evm platform.
--- arch/arm/mach-davinci/board-tnetv107x-evm.c | 45 +++++++++++++++++++++++++++ 1 files changed, 45 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +45 -0
@@ -25,6 +25,7 @@#include <linux/mtd/partitions.h> #include <linux/input.h> #include <linux/input/matrix_keypad.h> +#include <linux/spi/spi.h> #include <asm/mach/arch.h> #include <asm/mach-types.h>
@@ -38,6 +39,7 @@#define EVM_MMC_WP_GPIO 21#define EVM_MMC_CD_GPIO 24 +#define EVM_SPI_CS_GPIO 54static int initialize_gpio (int gpio,char *desc) {
@@ -203,9 +205,47 @@ static struct matrix_keypad_platform_data keypad_config = { .no_autorepeat = 0, }; +static void spi_select_device (int cs) +{ +static int gpio; + +if (!gpio) { +int ret; + ret =gpio_request (EVM_SPI_CS_GPIO ,"spi chipsel" ); +if (ret <0 ) { +pr_err ("cannot open spi chipsel gpio\n" ); + gpio = -ENOSYS ; +return ; + }else { + gpio =EVM_SPI_CS_GPIO ; +gpio_direction_output (gpio,0 ); + } + } + +if (gpio <0 ) +return ; + +return gpio_set_value (gpio, cs ?1 :0 ); +} + +static const struct ti_ssp_spi_data spi_master_data = { + .num_cs =2 , + .select = spi_select_device, +}; +static struct ti_ssp_data ssp_config = { .out_clock =250 *1000 , .dev_data = { + [1 ] = { + .dev_name ="ti-ssp-spi" , + .iosel =SSP_PIN_SEL (0 ,SSP_CLOCK ) | +SSP_PIN_SEL (1 ,SSP_DATA ) | +SSP_PIN_SEL (2 ,SSP_CHIPSEL ) | +SSP_PIN_SEL (3 ,SSP_IN ) | +SSP_INPUT_SEL (3 ), + .pdata = &spi_master_data, + .pdata_sz =sizeof (spi_master_data), + }, }, };
@@ -217,6 +257,9 @@ static struct tnetv107x_device_info evm_device_info __initconst = { .ssp_config = &ssp_config, }; +static struct spi_board_info spi_info[]__initconst = { +}; +static __init void tnetv107x_evm_board_init (void ) {davinci_cfg_reg_list (sdio1_pins);
@@ -224,6 +267,8 @@ static __init void tnetv107x_evm_board_init(void)davinci_cfg_reg_list (ssp_pins);tnetv107x_devices_init (&evm_device_info); + +spi_register_board_info (spi_info,ARRAY_SIZE (spi_info)); }#ifdef CONFIG_SERIAL_8250_CONSOLE
Signature · 9 lines
1.7.0.4 ------------------------------------------------------------------------------ Download new Adobe(R) Flash(R) Builder(TM) 4 The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly Flex(R) Builder(TM)) enable the development of rich applications that run across multiple browsers and platforms. Download your free trials today! http://p.sf.net/sfu/adobe-dev2dev
PATCH v2 6/12 regulator: add driver for tps6524x regulator
In reply to a message not in the archiveTPS6524X provides three step-down converters and two general-purpose LDO voltage regulators. This device is interfaced using SPI.
--- drivers/regulator/Kconfig | 10 + drivers/regulator/Makefile | 1 + drivers/regulator/tps6524x-regulator.c | 692 ++++++++++++++++++++++++++++++++ 3 files changed, 703 insertions(+), 0 deletions(-) create mode 100644 drivers/regulator/tps6524x-regulator.c
drivers/regulator/Kconfig +10 -0
@@ -235,5 +235,15 @@ config REGULATOR_TPS6586X help This driver supports TPS6586X voltage regulator chips. +config REGULATOR_TPS6524X + tristate "TI TPS6524X Power regulators" + depends on TI_SSP + help + This driver supports TPS6524X voltage regulator chips. TPS6524X + provides three step-down converters and two general-purpose LDO + voltage regulators. This device is interfaced using a customized + serial interface currently supported on the sequencer serial + port controller. + endif
drivers/regulator/Makefile +1 -0
@@ -33,6 +33,7 @@ obj-$(CONFIG_REGULATOR_AB3100) += ab3100.o obj-$(CONFIG_REGULATOR_TPS65023) += tps65023-regulator.o obj-$(CONFIG_REGULATOR_TPS6507X) += tps6507x-regulator.o +obj-$(CONFIG_REGULATOR_TPS6524X) += tps6524x-regulator.o obj-$(CONFIG_REGULATOR_88PM8607) += 88pm8607.o obj-$(CONFIG_REGULATOR_ISL6271A) += isl6271a-regulator.o obj-$(CONFIG_REGULATOR_AB8500) += ab8500.o
drivers/regulator/tps6524x-regulator.c new file +692 -0
692 lines not on this page · raw message
Signature · 9 lines
1.7.0.4 ------------------------------------------------------------------------------ Download new Adobe(R) Flash(R) Builder(TM) 4 The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly Flex(R) Builder(TM)) enable the development of rich applications that run across multiple browsers and platforms. Download your free trials today! http://p.sf.net/sfu/adobe-dev2dev
A message that is not in the archive (sent off-list or not yet received): 1287429922-18870-7-git-send-email-cyril-l0cyMroinI0@public.gmane.org
Mark Brown
Acked-byRe: [PATCH v2 06/12] regulator: add driver for tps6524x regulator
Quoted 4 lines · Cyril Chemparathy
TPS6524X provides three step-down converters and two general-purpose LDO voltage regulators. This device is interfaced using SPI.
Signed-off-by Cyril Chemparathy <[email protected]>
PATCH v2 7/12 davinci: add tnetv107x evm regulators
In reply to a message not in the archiveThis patch adds regulator and spi board info definitions for the tps6524x power management IC found on tnetv107x evm boards.
--- arch/arm/mach-davinci/board-tnetv107x-evm.c | 85 +++++++++++++++++++++++++++ 1 files changed, 85 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +85 -0
@@ -26,6 +26,9 @@#include <linux/input.h> #include <linux/input/matrix_keypad.h> #include <linux/spi/spi.h> +#include <linux/regulator/machine.h> +#include <linux/regulator/consumer.h> +#include <linux/regulator/driver.h> #include <asm/mach/arch.h> #include <asm/mach-types.h>
@@ -257,7 +260,89 @@ static struct tnetv107x_device_info evm_device_info __initconst = { .ssp_config = &ssp_config, }; +static struct regulator_consumer_supply usb_consumers[] = { +REGULATOR_SUPPLY ("vbus" ,"musb_hdrc.1" ), +}; + +static struct regulator_consumer_supply lcd_consumers[] = { +REGULATOR_SUPPLY ("vlcd" ,"tps6116x" ), +}; + +static struct regulator_init_data regulators[] = { + { + .constraints = { + .name ="DCDC1" , + .min_uV =1000000 , + .max_uV =1000000 , + .always_on =1 , + .boot_on =1 , + }, + }, + { + .constraints = { + .name ="DCDC2" , + .min_uV =1800000 , + .max_uV =1800000 , + .always_on =1 , + .boot_on =1 , + }, + }, + { + .constraints = { + .name ="DCDC3" , + .min_uV =3300000 , + .max_uV =3300000 , + .always_on =1 , + .boot_on =1 , + }, + }, + { + .constraints = { + .name ="LDO1" , + .min_uV =4800000 , + .max_uV =4800000 , + .always_on =1 , + .boot_on =1 , + }, + }, + { + .constraints = { + .name ="LDO1" , + .min_uV =3300000 , + .max_uV =3300000 , + .always_on =1 , + .boot_on =1 , + }, + }, + { + .num_consumer_supplies =ARRAY_SIZE (usb_consumers), + .consumer_supplies = usb_consumers, + .constraints = { + .name ="USB" , + .min_uA =200000 , + .max_uA =1000000 , + .valid_ops_mask =REGULATOR_CHANGE_CURRENT | +REGULATOR_CHANGE_STATUS , + }, + }, + { + .num_consumer_supplies =ARRAY_SIZE (lcd_consumers), + .consumer_supplies = lcd_consumers, + .constraints = { + .name ="LCD" , + .valid_ops_mask =REGULATOR_CHANGE_STATUS , + }, + }, +}; +static struct spi_board_info spi_info[]__initconst = { + { + .modalias ="tps6524x" , + .bus_num =1 , + .chip_select =0 , + .mode =SPI_MODE_0 , + .platform_data = regulators, + }, };static __init void tnetv107x_evm_board_init (void )
Signature · 9 lines
1.7.0.4 ------------------------------------------------------------------------------ Download new Adobe(R) Flash(R) Builder(TM) 4 The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly Flex(R) Builder(TM)) enable the development of rich applications that run across multiple browsers and platforms. Download your free trials today! http://p.sf.net/sfu/adobe-dev2dev
PATCH v2 8/12 gpio: add ti-ssp virtual gpio driver
In reply to a message not in the archiveThis patch adds a GPIO driver based on TI's SSP device. This driver does not support GPIO-IRQs.
--- arch/arm/mach-davinci/include/mach/ti_ssp.h | 4 + drivers/gpio/Kconfig | 10 ++ drivers/gpio/Makefile | 1 + drivers/gpio/ti-ssp-gpio.c | 200 +++++++++++++++++++++++++++ 4 files changed, 215 insertions(+), 0 deletions(-) create mode 100644 drivers/gpio/ti-ssp-gpio.c
arch/arm/mach-davinci/include/mach/ti_ssp.h +4 -0
@@ -39,6 +39,10 @@ struct ti_ssp_spi_data {void (*select)(int cs); }; +struct ti_ssp_gpio_data { +int start; +}; +/* * Sequencer port IO pin configuration bits. These do not correlate 1-1 with * the hardware. The iosel field in the port data combines iosel1 and iosel2,
drivers/gpio/Kconfig +10 -0
@@ -111,6 +111,16 @@ config GPIO_SCH This driver can also be built as a module. If so, the module will be called sch-gpio. +config GPIO_TI_SSP + tristate "TI SSP Controller GPIO Driver" + depends on GPIOLIB && TI_SSP + help + Say yes here to support a virtual GPIO interface on TI SSP ports. + Each SSP port translates into 4 GPIOs, with no IRQ support. + + This driver can also be built as a module. If so, the module + will be called ti-ssp-gpio. + comment "I2C GPIO expanders:" config GPIO_MAX7300
drivers/gpio/Makefile +1 -0
@@ -23,6 +23,7 @@ obj-$(CONFIG_GPIO_PL061) += pl061.o obj-$(CONFIG_GPIO_STMPE) += stmpe-gpio.o obj-$(CONFIG_GPIO_TC35892) += tc35892-gpio.o obj-$(CONFIG_GPIO_TIMBERDALE) += timbgpio.o +obj-$(CONFIG_GPIO_TI_SSP) += ti-ssp-gpio.o obj-$(CONFIG_GPIO_TWL4030) += twl4030-gpio.o obj-$(CONFIG_GPIO_UCB1400) += ucb1400_gpio.o obj-$(CONFIG_GPIO_XILINX) += xilinx_gpio.o
drivers/gpio/ti-ssp-gpio.c new file +200 -0
200 lines not on this page · raw message
Signature · 9 lines
1.7.0.4 ------------------------------------------------------------------------------ Download new Adobe(R) Flash(R) Builder(TM) 4 The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly Flex(R) Builder(TM)) enable the development of rich applications that run across multiple browsers and platforms. Download your free trials today! http://p.sf.net/sfu/adobe-dev2dev
A message that is not in the archive (sent off-list or not yet received): 1287429922-18870-9-git-send-email-cyril-l0cyMroinI0@public.gmane.org
Grant Likely
Acked-byRe: [PATCH v2 08/12] gpio: add ti-ssp virtual gpio driver
Quoted 4 lines · Cyril Chemparathy
This patch adds a GPIO driver based on TI's SSP device. This driver does not support GPIO-IRQs.
Signed-off-by Cyril Chemparathy <[email protected]>
Quoted 265 lines
--- arch/arm/mach-davinci/include/mach/ti_ssp.h | 4 + drivers/gpio/Kconfig | 10 ++ drivers/gpio/Makefile | 1 + drivers/gpio/ti-ssp-gpio.c | 200 +++++++++++++++++++++++++++ 4 files changed, 215 insertions(+), 0 deletions(-) create mode 100644 drivers/gpio/ti-ssp-gpio.carch/arm/mach-davinci/include/mach/ti_ssp.h +4
-0@@ -39,6 +39,10 @@ struct ti_ssp_spi_data {void (*select)(int cs); }; +struct ti_ssp_gpio_data { +int start; +}; +/* * Sequencer port IO pin configuration bits. These do not correlate 1-1 with * the hardware. The iosel field in the port data combines iosel1 and iosel2, drivers/gpio/Kconfig +10
-0@@ -111,6 +111,16 @@ config GPIO_SCH This driver can also be built as a module. If so, the module will be called sch-gpio. +config GPIO_TI_SSP + tristate "TI SSP Controller GPIO Driver" + depends on GPIOLIB && TI_SSP + help + Say yes here to support a virtual GPIO interface on TI SSP ports. + Each SSP port translates into 4 GPIOs, with no IRQ support. + + This driver can also be built as a module. If so, the module + will be called ti-ssp-gpio. + comment "I2C GPIO expanders:" config GPIO_MAX7300drivers/gpio/Makefile +1
-0@@ -23,6 +23,7 @@ obj-$(CONFIG_GPIO_PL061) += pl061.o obj-$(CONFIG_GPIO_STMPE) += stmpe-gpio.o obj-$(CONFIG_GPIO_TC35892) += tc35892-gpio.o obj-$(CONFIG_GPIO_TIMBERDALE) += timbgpio.o +obj-$(CONFIG_GPIO_TI_SSP) += ti-ssp-gpio.o obj-$(CONFIG_GPIO_TWL4030) += twl4030-gpio.o obj-$(CONFIG_GPIO_UCB1400) += ucb1400_gpio.o obj-$(CONFIG_GPIO_XILINX) += xilinx_gpio.odrivers/gpio/ti-ssp-gpio.c new file +200
-0@@ -0,0 +1,200 @@ +/* +* Sequencer Serial Port (SSP) based virtual GPIO driver +* +* Copyright (C) 2010 Texas Instruments Inc +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2 of the License, or +* (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA +*/ + +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/io.h> +#include <linux/err.h> +#include <linux/slab.h> +#include <linux/gpio.h> +#include <linux/platform_device.h> + +#include <mach/ti_ssp.h> + +struct ti_ssp_gpio { +struct gpio_chip chip; +#define chip2gpio (chip) container_of(chip, struct ti_ssp_gpio, chip) +struct device *dev; +spinlock_t lock; +u8 out; +u32 iosel; +}; + +static int direction_in (struct gpio_chip *chip,unsigned gpio_num) +{ +struct ti_ssp_gpio *gpio =chip2gpio (chip); +int error =0 ; + +spin_lock (&gpio->lock); + + gpio->iosel &= ~SSP_PIN_MASK (gpio_num); + gpio->iosel |=SSP_PIN_SEL (gpio_num,SSP_IN ); + + error =ti_ssp_set_iosel (gpio->dev, gpio->iosel); + +spin_unlock (&gpio->lock); + +return error; +} + +static int direction_out (struct gpio_chip *chip,unsigned gpio_num,int val) +{ +struct ti_ssp_gpio *gpio =chip2gpio (chip); +int error; + +spin_lock (&gpio->lock); + + gpio->iosel &= ~SSP_PIN_MASK (gpio_num); + gpio->iosel |=SSP_PIN_SEL (gpio_num,SSP_OUT ); + + error =ti_ssp_set_iosel (gpio->dev, gpio->iosel); + +if (error <0 ) + goto error; + +if (val) + gpio->out |=BIT (gpio_num); +else + gpio->out &= ~BIT (gpio_num); + + error =ti_ssp_raw_write (gpio->dev, gpio->out); + +error: +spin_unlock (&gpio->lock); +return error; +} + +static int value_get (struct gpio_chip *chip,unsigned gpio_num) +{ +struct ti_ssp_gpio *gpio =chip2gpio (chip); +int ret; + +spin_lock (&gpio->lock); + + ret =ti_ssp_raw_read (gpio->dev); +if (ret >=0 ) + ret = (ret &BIT (gpio_num)) ?1 :0 ; + +spin_unlock (&gpio->lock); +return ret; +} + +static void value_set (struct gpio_chip *chip,unsigned gpio_num,int val) +{ +struct ti_ssp_gpio *gpio =chip2gpio (chip); + +spin_lock (&gpio->lock); + +if (val) + gpio->out |=BIT (gpio_num); +else + gpio->out &= ~BIT (gpio_num); + +ti_ssp_raw_write (gpio->dev, gpio->out); + +spin_unlock (&gpio->lock); +} + +static int __devinit ti_ssp_gpio_probe (struct platform_device *pdev) +{ +const struct ti_ssp_gpio_data *pdata = pdev->dev.platform_data; +struct device *dev = &pdev->dev; +struct ti_ssp_gpio *gpio; +int error; + +if (!pdata) { +dev_err (dev,"platform data not found\n" ); +return -EINVAL ; + } + + gpio =kzalloc (sizeof (*gpio),GFP_KERNEL ); +if (!gpio) { +dev_err (dev,"cannot allocate driver data\n" ); +return -ENOMEM ; + } + + gpio->dev = dev; + gpio->iosel =SSP_PIN_SEL (0 ,SSP_IN ) |SSP_PIN_SEL (1 ,SSP_IN ) | +SSP_PIN_SEL (2 ,SSP_IN ) |SSP_PIN_SEL (3 ,SSP_IN ); +spin_lock_init (&gpio->lock); +platform_set_drvdata (pdev, gpio); + + gpio->chip.base = pdata->start; + gpio->chip.ngpio =4 ; + gpio->chip.dev = &pdev->dev; + gpio->chip.label ="ti_ssp_gpio" ; + gpio->chip.owner =THIS_MODULE ; + gpio->chip.get = value_get; + gpio->chip.set = value_set; + gpio->chip.direction_input = direction_in; + gpio->chip.direction_output = direction_out; + + error =gpiochip_add (&gpio->chip); +if (error <0 ) { +dev_err (dev,"gpio chip registration failed (%d)\n" , error); + goto error; + } + +dev_info (dev,"ssp gpio interface registered\n" ); +return 0 ; + +error: +kfree (gpio); +return error; +} + +static int __devexit ti_ssp_gpio_remove(struct platform_device *pdev) +{ +struct ti_ssp_gpio *gpio =platform_get_drvdata (pdev); +int error; + + error =gpiochip_remove (&gpio->chip); +if (error <0 ) +return error; +kfree (gpio); +return 0 ; +} + +static struct platform_driver ti_ssp_gpio_driver = { + .probe = ti_ssp_gpio_probe, + .remove =__devexit_p (ti_ssp_gpio_remove), + .driver = { + .name ="ti-ssp-gpio" , + .owner =THIS_MODULE , + }, +}; + +static int __init ti_ssp_gpio_init (void ) +{ +return platform_driver_register (&ti_ssp_gpio_driver); +} +subsys_initcall (ti_ssp_gpio_init); + +static void __exit ti_ssp_gpio_exit(void) +{ +platform_driver_unregister (&ti_ssp_gpio_driver); +} +module_exit (ti_ssp_gpio_exit); + +MODULE_DESCRIPTION ("GPIO interface for TI-SSP" ); +MODULE_AUTHOR ("Cyril Chemparathy <[email protected]>" ); +MODULE_LICENSE ("GPL" ); +MODULE_ALIAS ("platform:ti-ssp-gpio" );Signature · 1 line
1.7.0.4
------------------------------------------------------------------------------
Nokia and AT&T present the 2010 Calling All Innovators-North America contest Create new apps & games for the Nokia N8 for consumers in U.S. and Canada $10 million total in prizes - $4M cash, 500 devices, nearly $6M in marketing Develop with Nokia Qt SDK, Web Runtime, or Java and Publish to Ovi Store
http://p.sf.net/sfu/nokia-dev2dev
Re: [PATCH v2 08/12] gpio: add ti-ssp virtual gpio driver
In reply to a message not in the archiveQuoted 2 lines · Cyril Chemparathy
This patch adds a GPIO driver based on TI's SSP device. This driver does not support GPIO-IRQs.
Doesn't look particularly evil, except I don't much like the notion of needing a "stack" if it's not being used like an MFD where numerous functions are accessed concurrently, better IMO to just have each function's driver bind exclusively to the chip (and drive it in the mode it supports -- SPI, GPIO etc).
Also, the patch description is weak/confusing. First, there's not a thing "virtual" about this. Second, just say that this GPIO driver is bypassing pretty much everything in the SSP module (notably, all the silicon support for serial protocols) and just driving some of the pins as GPIOs. (Right?)
Quoted 30 lines
Signed-off-by Cyril Chemparathy <[email protected]>--- arch/arm/mach-davinci/include/mach/ti_ssp.h | 4 + drivers/gpio/Kconfig | 10 ++ drivers/gpio/Makefile | 1 + drivers/gpio/ti-ssp-gpio.c | 200 +++++++++++++++++++++++++++ 4 files changed, 215 insertions(+), 0 deletions(-) create mode 100644 drivers/gpio/ti-ssp-gpio.carch/arm/mach-davinci/include/mach/ti_ssp.h +4
-0@@ -39,6 +39,10 @@ struct ti_ssp_spi_data {void (*select)(int cs); }; +struct ti_ssp_gpio_data { +int start; +}; +/* * Sequencer port IO pin configuration bits. These do not correlate 1-1 with * the hardware. The iosel field in the port data combines iosel1 and iosel2, drivers/gpio/Kconfig +0
-0
drivers/gpio/Kconfig config GPIO_SCH · line 119
Quoted 9 lines
drivers/gpio/Kconfig +6
-0@@ -111,6 +111,16 @@ config GPIO_SCH This driver can also be built as a module. If so, the module will be called sch-gpio. +config GPIO_TI_SSP + tristate "TI SSP Controller GPIO Driver" + depends on GPIOLIB && TI_SSP + help + Say yes here to support a virtual GPIO interface on TI SSP ports. + Each SSP port translates into 4 GPIOs, with no IRQ support.
Don't emphasize the "no IRQ part so much; lots of GPIOs don't do IRQs. If a board uses SSP this way, it won't care; Kconfig users have no control over such board wiring issues.
Quoted 225 lines
drivers/gpio/Kconfig +4
-0+ + This driver can also be built as a module. If so, the module + will be called ti-ssp-gpio. + comment "I2C GPIO expanders:" config GPIO_MAX7300drivers/gpio/Makefile +1
-0@@ -23,6 +23,7 @@ obj-$(CONFIG_GPIO_PL061) += pl061.o obj-$(CONFIG_GPIO_STMPE) += stmpe-gpio.o obj-$(CONFIG_GPIO_TC35892) += tc35892-gpio.o obj-$(CONFIG_GPIO_TIMBERDALE) += timbgpio.o +obj-$(CONFIG_GPIO_TI_SSP) += ti-ssp-gpio.o obj-$(CONFIG_GPIO_TWL4030) += twl4030-gpio.o obj-$(CONFIG_GPIO_UCB1400) += ucb1400_gpio.o obj-$(CONFIG_GPIO_XILINX) += xilinx_gpio.odrivers/gpio/ti-ssp-gpio.c new file +200
-0@@ -0,0 +1,200 @@ +/* +* Sequencer Serial Port (SSP) based virtual GPIO driver +* +* Copyright (C) 2010 Texas Instruments Inc +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2 of the License, or +* (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA +*/ + +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/io.h> +#include <linux/err.h> +#include <linux/slab.h> +#include <linux/gpio.h> +#include <linux/platform_device.h> + +#include <mach/ti_ssp.h> + +struct ti_ssp_gpio { +struct gpio_chip chip; +#define chip2gpio (chip) container_of(chip, struct ti_ssp_gpio, chip) +struct device *dev; +spinlock_t lock; +u8 out; +u32 iosel; +}; + +static int direction_in (struct gpio_chip *chip,unsigned gpio_num) +{ +struct ti_ssp_gpio *gpio =chip2gpio (chip); +int error =0 ; + +spin_lock (&gpio->lock); + + gpio->iosel &= ~SSP_PIN_MASK (gpio_num); + gpio->iosel |=SSP_PIN_SEL (gpio_num,SSP_IN ); + + error =ti_ssp_set_iosel (gpio->dev, gpio->iosel); + +spin_unlock (&gpio->lock); + +return error; +} + +static int direction_out (struct gpio_chip *chip,unsigned gpio_num,int val) +{ +struct ti_ssp_gpio *gpio =chip2gpio (chip); +int error; + +spin_lock (&gpio->lock); + + gpio->iosel &= ~SSP_PIN_MASK (gpio_num); + gpio->iosel |=SSP_PIN_SEL (gpio_num,SSP_OUT ); + + error =ti_ssp_set_iosel (gpio->dev, gpio->iosel); + +if (error <0 ) + goto error; + +if (val) + gpio->out |=BIT (gpio_num); +else + gpio->out &= ~BIT (gpio_num); + + error =ti_ssp_raw_write (gpio->dev, gpio->out); + +error: +spin_unlock (&gpio->lock); +return error; +} + +static int value_get (struct gpio_chip *chip,unsigned gpio_num) +{ +struct ti_ssp_gpio *gpio =chip2gpio (chip); +int ret; + +spin_lock (&gpio->lock); + + ret =ti_ssp_raw_read (gpio->dev); +if (ret >=0 ) + ret = (ret &BIT (gpio_num)) ?1 :0 ; + +spin_unlock (&gpio->lock); +return ret; +} + +static void value_set (struct gpio_chip *chip,unsigned gpio_num,int val) +{ +struct ti_ssp_gpio *gpio =chip2gpio (chip); + +spin_lock (&gpio->lock); + +if (val) + gpio->out |=BIT (gpio_num); +else + gpio->out &= ~BIT (gpio_num); + +ti_ssp_raw_write (gpio->dev, gpio->out); + +spin_unlock (&gpio->lock); +} + +static int __devinit ti_ssp_gpio_probe (struct platform_device *pdev) +{ +const struct ti_ssp_gpio_data *pdata = pdev->dev.platform_data; +struct device *dev = &pdev->dev; +struct ti_ssp_gpio *gpio; +int error; + +if (!pdata) { +dev_err (dev,"platform data not found\n" ); +return -EINVAL ; + } + + gpio =kzalloc (sizeof (*gpio),GFP_KERNEL ); +if (!gpio) { +dev_err (dev,"cannot allocate driver data\n" ); +return -ENOMEM ; + } + + gpio->dev = dev; + gpio->iosel =SSP_PIN_SEL (0 ,SSP_IN ) |SSP_PIN_SEL (1 ,SSP_IN ) | +SSP_PIN_SEL (2 ,SSP_IN ) |SSP_PIN_SEL (3 ,SSP_IN ); +spin_lock_init (&gpio->lock); +platform_set_drvdata (pdev, gpio); + + gpio->chip.base = pdata->start; + gpio->chip.ngpio =4 ; + gpio->chip.dev = &pdev->dev; + gpio->chip.label ="ti_ssp_gpio" ; + gpio->chip.owner =THIS_MODULE ; + gpio->chip.get = value_get; + gpio->chip.set = value_set; + gpio->chip.direction_input = direction_in; + gpio->chip.direction_output = direction_out; + + error =gpiochip_add (&gpio->chip); +if (error <0 ) { +dev_err (dev,"gpio chip registration failed (%d)\n" , error); + goto error; + } + +dev_info (dev,"ssp gpio interface registered\n" ); +return 0 ; + +error: +kfree (gpio); +return error; +} + +static int __devexit ti_ssp_gpio_remove(struct platform_device *pdev) +{ +struct ti_ssp_gpio *gpio =platform_get_drvdata (pdev); +int error; + + error =gpiochip_remove (&gpio->chip); +if (error <0 ) +return error; +kfree (gpio); +return 0 ; +} + +static struct platform_driver ti_ssp_gpio_driver = { + .probe = ti_ssp_gpio_probe, + .remove =__devexit_p (ti_ssp_gpio_remove), + .driver = { + .name ="ti-ssp-gpio" , + .owner =THIS_MODULE , + }, +}; + +static int __init ti_ssp_gpio_init (void ) +{ +return platform_driver_register (&ti_ssp_gpio_driver); +} +subsys_initcall (ti_ssp_gpio_init); + +static void __exit ti_ssp_gpio_exit(void) +{ +platform_driver_unregister (&ti_ssp_gpio_driver); +} +module_exit (ti_ssp_gpio_exit); + +MODULE_DESCRIPTION ("GPIO interface for TI-SSP" ); +MODULE_AUTHOR ("Cyril Chemparathy <[email protected]>" ); +MODULE_LICENSE ("GPL" ); +MODULE_ALIAS ("platform:ti-ssp-gpio" );
Re: [PATCH v2 08/12] gpio: add ti-ssp virtual gpio driver
Hi David,
Quoted 9 lines · David Brownell
Quoted 2 lines · Cyril Chemparathy
This patch adds a GPIO driver based on TI's SSP device. This driver does not support GPIO-IRQs.
Doesn't look particularly evil, except I don't much like the notion of needing a "stack" if it's not being used like an MFD where numerous functions are accessed concurrently, better IMO to just have each function's driver bind exclusively to the chip (and drive it in the mode it supports -- SPI, GPIO etc).
SPI and GPIO are not the only modes that this hardware can be programmed to behave in. In future, other functions may be added as needed. I thought it would be best to keep the shared stuff reusable.
Quoted 5 lines
Also, the patch description is weak/confusing. First, there's not a thing "virtual" about this. Second, just say that this GPIO driver is bypassing pretty much everything in the SSP module (notably, all the silicon support for serial protocols) and just driving some of the pins as GPIOs. (Right?)
Sure.
[...]
Quoted 10 lines
drivers/gpio/Kconfig config GPIO_SCH · line 119
Quoted 6 lines
drivers/gpio/Kconfig +6
-0+config GPIO_TI_SSP + tristate "TI SSP Controller GPIO Driver" + depends on GPIOLIB && TI_SSP + help + Say yes here to support a virtual GPIO interface on TI SSP ports. + Each SSP port translates into 4 GPIOs, with no IRQ support.Don't emphasize the "no IRQ part so much; lots of GPIOs don't do IRQs. If a board uses SSP this way, it won't care;
Kconfigusers have no control over such board wiring issues.
Agreed.
Thanks
Cyril.
A message that is not in the archive (sent off-list or not yet received): [email protected]
Re: [PATCH v2 08/12] gpio: add ti-ssp virtual gpio driver
Quoted 5 lines
Quoted 3 lines
Doesn't look particularly evil, except I don't much
like the notion of
Quoted 1 line
needing a "stack" if it's not being used
Quoted 8 lines
like an MFD where numerous
Quoted 1 line
functions are accessed concurrently,
better IMO to just have each function's driver bind exclusively to the chip (and drive it in the
Quoted 1 line
mode it supports -- SPI, GPIO etc).
SPI and GPIO are not the only modes that
this hardware can be programmed
I know; ergo the "etc". This is common for serial engines. Many have enough flexibility to hook up to several flavors of audio codec too.
Quoted 2 lines
to behave in. In future, other functions may be added as needed.
And each one would have its own driver.
Quoted 2 lines
I thought it would be best to keep the
shared stuff reusable.
The way I've seen that done in the past is to keep the register decls clean enough so most drivers use them directly ... and in a few cases, provide some library code (if there is a a good reason to share any logic). (But it often turned out that the functions couldn't share much beyond the register layouts, since behaviors of each function differ so widely.
Quoted 1 line
Quoted 2 lines
there's not a
Quoted 1 line
thing "virtual" about this.
PATCH v2 9/12 davinci: add tnetv107x evm ti-ssp gpio device
In reply to a message not in the archiveThis patch adds definitions to hook up one of the ti-ssp ports to the SSP GPIO driver.
--- arch/arm/mach-davinci/board-tnetv107x-evm.c | 15 +++++++++++++++ 1 files changed, 15 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +15 -0
@@ -40,6 +40,8 @@#include <mach/ti_ssp.h> #include <mach/tnetv107x.h> +#define SSP_GPIO_START 128 +#define EVM_MMC_WP_GPIO 21#define EVM_MMC_CD_GPIO 24#define EVM_SPI_CS_GPIO 54
@@ -236,9 +238,22 @@ static const struct ti_ssp_spi_data spi_master_data = { .select = spi_select_device, }; +static const struct ti_ssp_gpio_data ssp_gpio_data = { + .start =SSP_GPIO_START , +}; +static struct ti_ssp_data ssp_config = { .out_clock =250 *1000 , .dev_data = { + [0 ] = { + .dev_name ="ti-ssp-gpio" , + .iosel =SSP_PIN_SEL (0 ,SSP_IN ) | +SSP_PIN_SEL (1 ,SSP_IN ) | +SSP_PIN_SEL (2 ,SSP_IN ) | +SSP_PIN_SEL (3 ,SSP_IN ), + .pdata = &ssp_gpio_data, + .pdata_sz =sizeof (ssp_gpio_data), + }, [1 ] = { .dev_name ="ti-ssp-spi" , .iosel = SSP_PIN_SEL(0, SSP_CLOCK) |
Signature · 9 lines
1.7.0.4 ------------------------------------------------------------------------------ Download new Adobe(R) Flash(R) Builder(TM) 4 The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly Flex(R) Builder(TM)) enable the development of rich applications that run across multiple browsers and platforms. Download your free trials today! http://p.sf.net/sfu/adobe-dev2dev
PATCH v2 10/12 backlight: add support for tps6116x controller
In reply to a message not in the archiveTPS6116x is an EasyScale backlight controller device. This driver supports TPS6116x devices connected on a single GPIO.
--- drivers/video/backlight/Kconfig | 7 + drivers/video/backlight/Makefile | 2 +- drivers/video/backlight/tps6116x.c | 340 ++++++++++++++++++++++++++++++++++++ 3 files changed, 348 insertions(+), 1 deletions(-) create mode 100644 drivers/video/backlight/tps6116x.c
drivers/video/backlight/Kconfig +7 -0
@@ -307,6 +307,13 @@ config BACKLIGHT_PCF50633 If you have a backlight driven by a NXP PCF50633 MFD, say Y here to enable its driver. +config BACKLIGHT_TPS6116X + tristate "TPS6116X LCD Backlight" + depends on GENERIC_GPIO + help + This driver controls the LCD backlight level for EasyScale capable + SSP connected backlight controllers. + endif # BACKLIGHT_CLASS_DEVICE endif # BACKLIGHT_LCD_SUPPORT
drivers/video/backlight/Makefile +1 -1
@@ -35,4 +35,4 @@ obj-$(CONFIG_BACKLIGHT_ADP5520) += adp5520_bl.o obj-$(CONFIG_BACKLIGHT_ADP8860) += adp8860_bl.o obj-$(CONFIG_BACKLIGHT_88PM860X) += 88pm860x_bl.o obj-$(CONFIG_BACKLIGHT_PCF50633) += pcf50633-backlight.o - +obj-$(CONFIG_BACKLIGHT_TPS6116X)+= tps6116x.o
drivers/video/backlight/tps6116x.c new file +340 -0
340 lines not on this page · raw message
Signature · 9 lines
1.7.0.4 ------------------------------------------------------------------------------ Download new Adobe(R) Flash(R) Builder(TM) 4 The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly Flex(R) Builder(TM)) enable the development of rich applications that run across multiple browsers and platforms. Download your free trials today! http://p.sf.net/sfu/adobe-dev2dev
PATCH v2 11/12 davinci: add tnetv107x evm backlight device
In reply to a message not in the archiveThe tnetv107x evm board has a backlight device that is connected on one of the SSP ports. This patch adds the board definitions necessary to plug the backlight driver to the GPIO corresponding to this SSP pin.
--- arch/arm/mach-davinci/board-tnetv107x-evm.c | 9 +++++++++ 1 files changed, 9 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +9 -0
@@ -45,6 +45,7 @@#define EVM_MMC_WP_GPIO 21#define EVM_MMC_CD_GPIO 24#define EVM_SPI_CS_GPIO 54 +#define EVM_BACKLIGHT_GPIO (SSP_GPIO_START + 2)static int initialize_gpio (int gpio,char *desc) {
@@ -360,6 +361,12 @@ static struct spi_board_info spi_info[] __initconst = { }, }; +static struct platform_device backlight_device = { + .name ="tps6116x" , + .id =-1 , + .dev.platform_data = (void *)EVM_BACKLIGHT_GPIO , +}; +static __init void tnetv107x_evm_board_init (void ) {davinci_cfg_reg_list (sdio1_pins);
@@ -368,6 +375,8 @@ static __init void tnetv107x_evm_board_init(void)tnetv107x_devices_init (&evm_device_info); +platform_device_register (&backlight_device); +spi_register_board_info (spi_info,ARRAY_SIZE (spi_info)); }
Signature · 9 lines
1.7.0.4 ------------------------------------------------------------------------------ Download new Adobe(R) Flash(R) Builder(TM) 4 The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly Flex(R) Builder(TM)) enable the development of rich applications that run across multiple browsers and platforms. Download your free trials today! http://p.sf.net/sfu/adobe-dev2dev
PATCH v2 12/12 davinci: add tnetv107x evm i2c eeprom device
In reply to a message not in the archiveThe tnetv107x evm board has an I2C device connected on one of the SSP ports. This patch adds board definitions for a GPIO based I2C master, as well as definitions for the eeprom device on these boards.
--- arch/arm/mach-davinci/board-tnetv107x-evm.c | 30 +++++++++++++++++++++++++++ 1 files changed, 30 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +30 -0
@@ -29,6 +29,9 @@#include <linux/regulator/machine.h> #include <linux/regulator/consumer.h> #include <linux/regulator/driver.h> +#include <linux/i2c.h> +#include <linux/i2c/at24.h> +#include <linux/i2c-gpio.h> #include <asm/mach/arch.h> #include <asm/mach-types.h>
@@ -45,6 +48,8 @@#define EVM_MMC_WP_GPIO 21#define EVM_MMC_CD_GPIO 24#define EVM_SPI_CS_GPIO 54 +#define EVM_I2C_SDA_GPIO (SSP_GPIO_START + 0) +#define EVM_I2C_SCL_GPIO (SSP_GPIO_START + 1)#define EVM_BACKLIGHT_GPIO (SSP_GPIO_START + 2)static int initialize_gpio (int gpio,char *desc)
@@ -367,6 +372,29 @@ static struct platform_device backlight_device = { .dev.platform_data = (void *)EVM_BACKLIGHT_GPIO, }; +struct i2c_gpio_platform_data i2c_data = { + .sda_pin =EVM_I2C_SDA_GPIO , + .scl_pin =EVM_I2C_SCL_GPIO , +}; + +static struct platform_device i2c_device = { + .name ="i2c-gpio" , + .id =0 , + .dev.platform_data = &i2c_data, +}; + +static struct at24_platform_data at24_config = { + .byte_len =SZ_16K /8 , + .page_size =16 , +}; + +static struct i2c_board_info i2c_info[]__initconst = { + { +I2C_BOARD_INFO ("24c16" ,0x50 ), + .platform_data = &at24_config, + }, +}; +static __init void tnetv107x_evm_board_init (void ) {davinci_cfg_reg_list (sdio1_pins);
@@ -376,8 +404,10 @@ static __init void tnetv107x_evm_board_init(void)tnetv107x_devices_init (&evm_device_info);platform_device_register (&backlight_device); +platform_device_register (&i2c_device);spi_register_board_info (spi_info,ARRAY_SIZE (spi_info)); +i2c_register_board_info (0 , i2c_info,ARRAY_SIZE (i2c_info)); }#ifdef CONFIG_SERIAL_8250_CONSOLE
Signature · 9 lines
1.7.0.4 ------------------------------------------------------------------------------ Download new Adobe(R) Flash(R) Builder(TM) 4 The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly Flex(R) Builder(TM)) enable the development of rich applications that run across multiple browsers and platforms. Download your free trials today! http://p.sf.net/sfu/adobe-dev2dev
Quoted 3 lines · Cyril Chemparathy
TI's sequencer serial port (TI-SSP) is a jack-of-all-trades type of serial port device. It has a built-in programmable execution engine that can be programmed to operate as almost any serial bus (I2C, SPI, EasyScale, and others).
Hi Cyril,
Can you do one more posting, including the acks from the subsystem maintainers so far, and posting also to LKML and linux-arm-kernel-IAPFreCvJWM7uuMidbF8XZu6nac5fYnt@public.gmane.org
Also the backlight driver needs a review/ack from Richard Purdie (search for drivers/video/backlight in MAINTAINERS).
With acks from all the subsystem maintainers, I think it makes sense to
merge all of these together via the davinci tree. At the moment, I'm
not sure who the final authority on the drivers/misc stuff is, but I will ask in response to your updated posting.
Thanks,
Kevin
Quoted 74 lines
This patch series implements a driver stack that looks like the following:
+--------+ | eeprom | . . . +--------+ +-----------+ +--------------+ +---------+ | regulator | . . . | i2c-gpio | | 1-wire | . . . +-----------+ +--------------+ +---------+ +----------------------+ +--------------------------------+ | ssp-spi | | ssp-gpio | +----------------------+ +--------------------------------+ +----------------------------------------------------------+ | ssp | +----------------------------------------------------------+Changes between v1 and v2 of this series:
- Replaced open()/close() semantics with dynamic
platform_deviceregistration on SSP probe.- Removed user-land interface to regulator registers
- More sensible regulator constraints
- Other minor cleanups
Cyril Chemparathy (12):
misc: add driver for sequencer serial port
davinci: add tnetv107x ssp platform device
davinci: add ssp config for tnetv107x evm board
spi: add ti-ssp spi master driver
davinci: add spi devices on tnetv107x evm
regulator: add driver for tps6524x regulator
davinci: add tnetv107x evm regulators
gpio: add ti-ssp virtual gpio driver
davinci: add tnetv107x evm ti-ssp gpio device
backlight: add support for tps6116x controller
davinci: add tnetv107x evm backlight device
davinci: add tnetv107x evm i2c eeprom devicearch/arm/mach-davinci/board-tnetv107x-evm.c | 199 +++++++ arch/arm/mach-davinci/devices-tnetv107x.c | 25 + arch/arm/mach-davinci/include/mach/ti_ssp.h | 99 ++++ arch/arm/mach-davinci/include/mach/tnetv107x.h | 2 + arch/arm/mach-davinci/tnetv107x.c | 2 +- drivers/gpio/Kconfig | 10 + drivers/gpio/Makefile | 1 + drivers/gpio/ti-ssp-gpio.c | 200 +++++++ drivers/misc/Kconfig | 11 + drivers/misc/Makefile | 1 + drivers/misc/ti_ssp.c | 436 +++++++++++++++ drivers/regulator/Kconfig | 10 + drivers/regulator/Makefile | 1 + drivers/regulator/tps6524x-regulator.c | 692 ++++++++++++++++++++++++ drivers/spi/Kconfig | 6 + drivers/spi/Makefile | 1 + drivers/spi/spi_ti_ssp.c | 397 ++++++++++++++ drivers/video/backlight/Kconfig | 7 + drivers/video/backlight/Makefile | 2 +- drivers/video/backlight/tps6116x.c | 340 ++++++++++++ 20 files changed, 2440 insertions(+), 2 deletions(-) create mode 100644 arch/arm/mach-davinci/include/mach/ti_ssp.h create mode 100644 drivers/gpio/ti-ssp-gpio.c create mode 100644 drivers/misc/ti_ssp.c create mode 100644 drivers/regulator/tps6524x-regulator.c create mode 100644 drivers/spi/spi_ti_ssp.c create mode 100644 drivers/video/backlight/tps6116x.c_______________________________________________
Davinci-linux-open-source mailing list Davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/@public.gmane.org
http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source