Skip to contentSkip to conversation

ARM: S5PV310: Add audio platform devices

PATCH New Jassi Brar 2 participants 5 messages Oct 26, 2010

Subsystems (3)
lore
Share & tools
lore

Jassi Brar

author
#0 lore raw

PATCH 9/9 ARM: S5PV310: Add audio platform devices

From: Jassi Brar <[email protected]>

Define platform devices for all audio devices found on S5PV310

---
 arch/arm/mach-s5pv310/Makefile            |    1 +
 arch/arm/mach-s5pv310/dev-audio.c         |  364 +++++++++++++++++++++++++++++
 arch/arm/mach-s5pv310/include/mach/map.h  |   16 ++
 arch/arm/plat-samsung/include/plat/devs.h |    9 +
 4 files changed, 390 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-s5pv310/dev-audio.c
arch/arm/mach-s5pv310/Makefile +1 -0
index d265adb..61e3cb6 100644
@@ -27,6 +27,7 @@ obj-$(CONFIG_MACH_UNIVERSAL_C210)	+= mach-universal_c210.o
 
 # device support
 
+obj-y += dev-audio.o
 obj-$(CONFIG_S5PV310_SETUP_I2C1)	+= setup-i2c1.o
 obj-$(CONFIG_S5PV310_SETUP_I2C2)	+= setup-i2c2.o
 obj-$(CONFIG_S5PV310_SETUP_I2C3)	+= setup-i2c3.o
arch/arm/mach-s5pv310/dev-audio.c new file +364 -0

364 lines not on this page · raw message

arch/arm/mach-s5pv310/include/mach/map.h +16 -0
index f6a6587..d99eff3 100644
@@ -61,6 +61,22 @@
 
 #define S5PV310_PA_HSMMC(x)		(0x12510000 + ((x) * 0x10000))
 
+/* S/PDIF */
+#define S5PV310_PA_SPDIF	0xE1100000
+
+/* I2S */
+#define S5PV310_PA_IIS0		0x03830000
+#define S5PV310_PA_IIS1		0xE3100000
+#define S5PV310_PA_IIS2		0xE2A00000
+
+/* PCM */
+#define S5PV310_PA_PCM0		0x03840000
+#define S5PV310_PA_PCM1		0x13980000
+#define S5PV310_PA_PCM2		0x13990000
+
+/* AC97 */
+#define S5PV310_PA_AC97		0x139A0000
+
 #define S5PV310_PA_UART			(0x13800000)
 
 #define S5P_PA_UART(x)			(S5PV310_PA_UART + ((x) * S3C_UART_OFFSET))
arch/arm/plat-samsung/include/plat/devs.h +9 -0
index 16521cc..9764268 100644
@@ -94,6 +94,15 @@ extern struct platform_device s5pv210_device_iis1;
 extern struct platform_device s5pv210_device_iis2;
 extern struct platform_device s5pv210_device_spdif;
 
+extern struct platform_device s5pv310_device_ac97;
+extern struct platform_device s5pv310_device_pcm0;
+extern struct platform_device s5pv310_device_pcm1;
+extern struct platform_device s5pv310_device_pcm2;
+extern struct platform_device s5pv310_device_iis0;
+extern struct platform_device s5pv310_device_iis1;
+extern struct platform_device s5pv310_device_iis2;
+extern struct platform_device s5pv310_device_spdif;
+
 extern struct platform_device s5p6442_device_pcm0;
 extern struct platform_device s5p6442_device_pcm1;
 extern struct platform_device s5p6442_device_iis0;
Signature · 1 line
1.6.2.5
#1 lore raw

PATCH 9/9 ARM: S5PV310: Add audio platform devices

Quoted 21 lines · Jassi Brar

From: Jassi Brar <[email protected]>

Define platform devices for all audio devices found on S5PV310

---

?arch/arm/mach-s5pv310/Makefile ? ? ? ? ? ?| ? ?1 +
?arch/arm/mach-s5pv310/dev-audio.c ? ? ? ? | ?364 +++++++++++++++++++++++++++++
?arch/arm/mach-s5pv310/include/mach/map.h ?| ? 16 ++
?arch/arm/plat-samsung/include/plat/devs.h | ? ?9 +

?4 files changed, 390 insertions(+), 0 deletions(-) ?create mode 100644 arch/arm/mach-s5pv310/dev-audio.c

arch/arm/mach-s5pv310/Makefile +0 -0
index d265adb..61e3cb6 100644
@@ -27,6 +27,7 @@ obj-$(CONFIG_MACH_UNIVERSAL_C210) ? ? += mach-universal_c210.o
 

?# device support

Quoted 1 line

+obj-y += dev-audio.o

Why it's default build? could you make a config as others?

Quoted 31 lines

?obj-$(CONFIG_S5PV310_SETUP_I2C1) ? ? ? += setup-i2c1.o ?obj-$(CONFIG_S5PV310_SETUP_I2C2) ? ? ? += setup-i2c2.o ?obj-$(CONFIG_S5PV310_SETUP_I2C3) ? ? ? += setup-i2c3.o

arch/arm/mach-s5pv310/dev-audio.c new file +22 -0
new file mode 100644
index 0000000..18ede29
@@ -0,0 +1,364 @@
+/* linux/arch/arm/mach-s5pv310/dev-audio.c
+ *
+ * Copyright (c) 2010 Samsung Electronics Co. Ltd
+ * ? ? Jaswinder Singh <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <linux/gpio.h>
+
+#include <plat/gpio-cfg.h>
+#include <plat/audio.h>
+
+#include <mach/map.h>
+#include <mach/dma.h>
+#include <mach/irqs.h>
+
+static const char *rclksrc[] = {

arch/arm/mach-s5pv310/dev-audio.c line 32

Quoted 10 lines
arch/arm/mach-s5pv310/dev-audio.c new file +10 -0
+ ? ? ? [0] = "busclk",
+ ? ? ? [1] = "i2sclk",
+};
+
+static int s5pv310_cfg_i2s(struct platform_device *pdev)
+{
+ ? ? ? /* configure GPIO for i2s port */
+ ? ? ? switch (pdev->id) {
+ ? ? ? case 0:
+ ? ? ? ? ? ? ? s3c_gpio_cfgpin_range(S5PV310_GPZ(0), 7, S3C_GPIO_SFN(2));

Does it default setup for i2s? In my board some pins are used for other purpose.
I mean GPZ(1, 5, 6) doesn't used it for I2S.
then how do you handle this one?

Quoted 17 lines
arch/arm/mach-s5pv310/dev-audio.c new file +17 -0
+ ? ? ? ? ? ? ? break;
+ ? ? ? case 1:
+ ? ? ? ? ? ? ? s3c_gpio_cfgpin_range(S5PV310_GPC0(0), 5, S3C_GPIO_SFN(2));
+ ? ? ? ? ? ? ? break;
+ ? ? ? case 2:
+ ? ? ? ? ? ? ? s3c_gpio_cfgpin_range(S5PV310_GPC1(0), 5, S3C_GPIO_SFN(4));
+ ? ? ? ? ? ? ? break;
+ ? ? ? default:
+ ? ? ? ? ? ? ? printk(KERN_ERR "Invalid Device %d\n", pdev->id);
+ ? ? ? ? ? ? ? return -EINVAL;
+ ? ? ? }
+
+ ? ? ? return 0;
+}
+
+static struct s3c_audio_pdata i2sv5_pdata = {
+ ? ? ? .cfg_gpio = s5pv310_cfg_i2s,

arch/arm/mach-s5pv310/dev-audio.c line 59

Quoted 10 lines
arch/arm/mach-s5pv310/dev-audio.c new file +10 -0
+ ? ? ? .type = {
+ ? ? ? ? ? ? ? .i2s = {
+ ? ? ? ? ? ? ? ? ? ? ? .quirks = QUIRK_PRI_6CHAN | QUIRK_SEC_DAI
+ ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ?| QUIRK_NEED_RSTCLR,
+ ? ? ? ? ? ? ? ? ? ? ? .src_clk = rclksrc,
+ ? ? ? ? ? ? ? },
+ ? ? ? },
+};
+
+static struct resource s5pv310_iis0_resource[] = {

You wrote that there are some users to use iis but c210/v310 doesn't. So you should use the i2s at least c210/v310 series

Quoted 339 lines
arch/arm/mach-s5pv310/dev-audio.c new file +305 -0
+ ? ? ? [0] = {
+ ? ? ? ? ? ? ? .start = S5PV310_PA_IIS0,
+ ? ? ? ? ? ? ? .end = S5PV310_PA_IIS0 + 0x100 - 1,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_MEM,
+ ? ? ? },
+ ? ? ? [1] = {
+ ? ? ? ? ? ? ? .start = DMACH_I2S0_TX,
+ ? ? ? ? ? ? ? .end = DMACH_I2S0_TX,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_DMA,
+ ? ? ? },
+ ? ? ? [2] = {
+ ? ? ? ? ? ? ? .start = DMACH_I2S0_RX,
+ ? ? ? ? ? ? ? .end = DMACH_I2S0_RX,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_DMA,
+ ? ? ? },
+ ? ? ? [3] = {
+ ? ? ? ? ? ? ? .start = DMACH_I2S0S_TX,
+ ? ? ? ? ? ? ? .end = DMACH_I2S0S_TX,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_DMA,
+ ? ? ? },
+};
+
+struct platform_device s5pv310_device_iis0 = {
+ ? ? ? .name = "samsung-i2s",
+ ? ? ? .id = 0,
+ ? ? ? .num_resources = ARRAY_SIZE(s5pv310_iis0_resource),
+ ? ? ? .resource = s5pv310_iis0_resource,
+ ? ? ? .dev = {
+ ? ? ? ? ? ? ? .platform_data = &i2sv5_pdata,
+ ? ? ? },
+};
+
+static const char *rclksrc_v3[] = {
+ ? ? ? [0] = "sclk_i2s",
+ ? ? ? [1] = "no_such_clock",
+};
+
+static struct s3c_audio_pdata i2sv3_pdata = {
+ ? ? ? .cfg_gpio = s5pv310_cfg_i2s,
+ ? ? ? .type = {
+ ? ? ? ? ? ? ? .i2s = {
+ ? ? ? ? ? ? ? ? ? ? ? .quirks = QUIRK_NO_MUXPSR,
+ ? ? ? ? ? ? ? ? ? ? ? .src_clk = rclksrc_v3,
+ ? ? ? ? ? ? ? },
+ ? ? ? },
+};
+
+static struct resource s5pv310_iis1_resource[] = {
+ ? ? ? [0] = {
+ ? ? ? ? ? ? ? .start = S5PV310_PA_IIS1,
+ ? ? ? ? ? ? ? .end = S5PV310_PA_IIS1 + 0x100 - 1,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_MEM,
+ ? ? ? },
+ ? ? ? [1] = {
+ ? ? ? ? ? ? ? .start = DMACH_I2S1_TX,
+ ? ? ? ? ? ? ? .end = DMACH_I2S1_TX,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_DMA,
+ ? ? ? },
+ ? ? ? [2] = {
+ ? ? ? ? ? ? ? .start = DMACH_I2S1_RX,
+ ? ? ? ? ? ? ? .end = DMACH_I2S1_RX,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_DMA,
+ ? ? ? },
+};
+
+struct platform_device s5pv310_device_iis1 = {
+ ? ? ? .name = "samsung-i2s",
+ ? ? ? .id = 1,
+ ? ? ? .num_resources = ARRAY_SIZE(s5pv310_iis1_resource),
+ ? ? ? .resource = s5pv310_iis1_resource,
+ ? ? ? .dev = {
+ ? ? ? ? ? ? ? .platform_data = &i2sv3_pdata,
+ ? ? ? },
+};
+
+static struct resource s5pv310_iis2_resource[] = {
+ ? ? ? [0] = {
+ ? ? ? ? ? ? ? .start = S5PV310_PA_IIS2,
+ ? ? ? ? ? ? ? .end = S5PV310_PA_IIS2 + 0x100 - 1,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_MEM,
+ ? ? ? },
+ ? ? ? [1] = {
+ ? ? ? ? ? ? ? .start = DMACH_I2S2_TX,
+ ? ? ? ? ? ? ? .end = DMACH_I2S2_TX,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_DMA,
+ ? ? ? },
+ ? ? ? [2] = {
+ ? ? ? ? ? ? ? .start = DMACH_I2S2_RX,
+ ? ? ? ? ? ? ? .end = DMACH_I2S2_RX,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_DMA,
+ ? ? ? },
+};
+
+struct platform_device s5pv310_device_iis2 = {
+ ? ? ? .name = "samsung-i2s",
+ ? ? ? .id = 2,
+ ? ? ? .num_resources = ARRAY_SIZE(s5pv310_iis2_resource),
+ ? ? ? .resource = s5pv310_iis2_resource,
+ ? ? ? .dev = {
+ ? ? ? ? ? ? ? .platform_data = &i2sv3_pdata,
+ ? ? ? },
+};
+
+/* PCM Controller platform_devices */
+
+static int s5pv310_pcm_cfg_gpio(struct platform_device *pdev)
+{
+ ? ? ? switch (pdev->id) {
+ ? ? ? case 0:
+ ? ? ? ? ? ? ? s3c_gpio_cfgpin_range(S5PV310_GPZ(0), 5, S3C_GPIO_SFN(3));
+ ? ? ? ? ? ? ? break;
+ ? ? ? case 1:
+ ? ? ? ? ? ? ? s3c_gpio_cfgpin_range(S5PV310_GPC0(0), 5, S3C_GPIO_SFN(3));
+ ? ? ? ? ? ? ? break;
+ ? ? ? case 2:
+ ? ? ? ? ? ? ? s3c_gpio_cfgpin_range(S5PV310_GPC1(0), 5, S3C_GPIO_SFN(3));
+ ? ? ? ? ? ? ? break;
+ ? ? ? default:
+ ? ? ? ? ? ? ? printk(KERN_DEBUG "Invalid PCM Controller number!");
+ ? ? ? ? ? ? ? return -EINVAL;
+ ? ? ? }
+
+ ? ? ? return 0;
+}
+
+static struct s3c_audio_pdata s3c_pcm_pdata = {
+ ? ? ? .cfg_gpio = s5pv310_pcm_cfg_gpio,
+};
+
+static struct resource s5pv310_pcm0_resource[] = {
+ ? ? ? [0] = {
+ ? ? ? ? ? ? ? .start = S5PV310_PA_PCM0,
+ ? ? ? ? ? ? ? .end = S5PV310_PA_PCM0 + 0x100 - 1,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_MEM,
+ ? ? ? },
+ ? ? ? [1] = {
+ ? ? ? ? ? ? ? .start = DMACH_PCM0_TX,
+ ? ? ? ? ? ? ? .end = DMACH_PCM0_TX,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_DMA,
+ ? ? ? },
+ ? ? ? [2] = {
+ ? ? ? ? ? ? ? .start = DMACH_PCM0_RX,
+ ? ? ? ? ? ? ? .end = DMACH_PCM0_RX,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_DMA,
+ ? ? ? },
+};
+
+struct platform_device s5pv310_device_pcm0 = {
+ ? ? ? .name = "samsung-pcm",
+ ? ? ? .id = 0,
+ ? ? ? .num_resources = ARRAY_SIZE(s5pv310_pcm0_resource),
+ ? ? ? .resource = s5pv310_pcm0_resource,
+ ? ? ? .dev = {
+ ? ? ? ? ? ? ? .platform_data = &s3c_pcm_pdata,
+ ? ? ? },
+};
+
+static struct resource s5pv310_pcm1_resource[] = {
+ ? ? ? [0] = {
+ ? ? ? ? ? ? ? .start = S5PV310_PA_PCM1,
+ ? ? ? ? ? ? ? .end = S5PV310_PA_PCM1 + 0x100 - 1,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_MEM,
+ ? ? ? },
+ ? ? ? [1] = {
+ ? ? ? ? ? ? ? .start = DMACH_PCM1_TX,
+ ? ? ? ? ? ? ? .end = DMACH_PCM1_TX,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_DMA,
+ ? ? ? },
+ ? ? ? [2] = {
+ ? ? ? ? ? ? ? .start = DMACH_PCM1_RX,
+ ? ? ? ? ? ? ? .end = DMACH_PCM1_RX,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_DMA,
+ ? ? ? },
+};
+
+struct platform_device s5pv310_device_pcm1 = {
+ ? ? ? .name = "samsung-pcm",
+ ? ? ? .id = 1,
+ ? ? ? .num_resources = ARRAY_SIZE(s5pv310_pcm1_resource),
+ ? ? ? .resource = s5pv310_pcm1_resource,
+ ? ? ? .dev = {
+ ? ? ? ? ? ? ? .platform_data = &s3c_pcm_pdata,
+ ? ? ? },
+};
+
+static struct resource s5pv310_pcm2_resource[] = {
+ ? ? ? [0] = {
+ ? ? ? ? ? ? ? .start = S5PV310_PA_PCM2,
+ ? ? ? ? ? ? ? .end = S5PV310_PA_PCM2 + 0x100 - 1,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_MEM,
+ ? ? ? },
+ ? ? ? [1] = {
+ ? ? ? ? ? ? ? .start = DMACH_PCM2_TX,
+ ? ? ? ? ? ? ? .end = DMACH_PCM2_TX,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_DMA,
+ ? ? ? },
+ ? ? ? [2] = {
+ ? ? ? ? ? ? ? .start = DMACH_PCM2_RX,
+ ? ? ? ? ? ? ? .end = DMACH_PCM2_RX,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_DMA,
+ ? ? ? },
+};
+
+struct platform_device s5pv310_device_pcm2 = {
+ ? ? ? .name = "samsung-pcm",
+ ? ? ? .id = 2,
+ ? ? ? .num_resources = ARRAY_SIZE(s5pv310_pcm2_resource),
+ ? ? ? .resource = s5pv310_pcm2_resource,
+ ? ? ? .dev = {
+ ? ? ? ? ? ? ? .platform_data = &s3c_pcm_pdata,
+ ? ? ? },
+};
+
+/* AC97 Controller platform devices */
+
+static int s5pv310_ac97_cfg_gpio(struct platform_device *pdev)
+{
+ ? ? ? return s3c_gpio_cfgpin_range(S5PV310_GPC0(0), 5, S3C_GPIO_SFN(4));
+}
+
+static struct resource s5pv310_ac97_resource[] = {
+ ? ? ? [0] = {
+ ? ? ? ? ? ? ? .start = S5PV310_PA_AC97,
+ ? ? ? ? ? ? ? .end = S5PV310_PA_AC97 + 0x100 - 1,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_MEM,
+ ? ? ? },
+ ? ? ? [1] = {
+ ? ? ? ? ? ? ? .start = DMACH_AC97_PCMOUT,
+ ? ? ? ? ? ? ? .end = DMACH_AC97_PCMOUT,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_DMA,
+ ? ? ? },
+ ? ? ? [2] = {
+ ? ? ? ? ? ? ? .start = DMACH_AC97_PCMIN,
+ ? ? ? ? ? ? ? .end = DMACH_AC97_PCMIN,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_DMA,
+ ? ? ? },
+ ? ? ? [3] = {
+ ? ? ? ? ? ? ? .start = DMACH_AC97_MICIN,
+ ? ? ? ? ? ? ? .end = DMACH_AC97_MICIN,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_DMA,
+ ? ? ? },
+ ? ? ? [4] = {
+ ? ? ? ? ? ? ? .start = IRQ_AC97,
+ ? ? ? ? ? ? ? .end = IRQ_AC97,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_IRQ,
+ ? ? ? },
+};
+
+static struct s3c_audio_pdata s3c_ac97_pdata = {
+ ? ? ? .cfg_gpio = s5pv310_ac97_cfg_gpio,
+};
+
+static u64 s5pv310_ac97_dmamask = DMA_BIT_MASK(32);
+
+struct platform_device s5pv310_device_ac97 = {
+ ? ? ? .name = "samsung-ac97",
+ ? ? ? .id = -1,
+ ? ? ? .num_resources = ARRAY_SIZE(s5pv310_ac97_resource),
+ ? ? ? .resource = s5pv310_ac97_resource,
+ ? ? ? .dev = {
+ ? ? ? ? ? ? ? .platform_data = &s3c_ac97_pdata,
+ ? ? ? ? ? ? ? .dma_mask = &s5pv310_ac97_dmamask,
+ ? ? ? ? ? ? ? .coherent_dma_mask = DMA_BIT_MASK(32),
+ ? ? ? },
+};
+
+/* S/PDIF Controller platform_device */
+
+static int s5pv310_spdif_cfg_gpio(struct platform_device *pdev)
+{
+ ? ? ? s3c_gpio_cfgpin_range(S5PV310_GPC1(0), 2, S3C_GPIO_SFN(3));
+
+ ? ? ? return 0;
+}
+
+static struct resource s5pv310_spdif_resource[] = {
+ ? ? ? [0] = {
+ ? ? ? ? ? ? ? .start = S5PV310_PA_SPDIF,
+ ? ? ? ? ? ? ? .end = S5PV310_PA_SPDIF + 0x100 - 1,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_MEM,
+ ? ? ? },
+ ? ? ? [1] = {
+ ? ? ? ? ? ? ? .start = DMACH_SPDIF,
+ ? ? ? ? ? ? ? .end = DMACH_SPDIF,
+ ? ? ? ? ? ? ? .flags = IORESOURCE_DMA,
+ ? ? ? },
+};
+
+static struct s3c_audio_pdata samsung_spdif_pdata = {
+ ? ? ? .cfg_gpio = s5pv310_spdif_cfg_gpio,
+};
+
+static u64 s5pv310_spdif_dmamask = DMA_BIT_MASK(32);
+
+struct platform_device s5pv310_device_spdif = {
+ ? ? ? .name = "samsung-spdif",
+ ? ? ? .id = -1,
+ ? ? ? .num_resources = ARRAY_SIZE(s5pv310_spdif_resource),
+ ? ? ? .resource = s5pv310_spdif_resource,
+ ? ? ? .dev = {
+ ? ? ? ? ? ? ? .platform_data = &samsung_spdif_pdata,
+ ? ? ? ? ? ? ? .dma_mask = &s5pv310_spdif_dmamask,
+ ? ? ? ? ? ? ? .coherent_dma_mask = DMA_BIT_MASK(32),
+ ? ? ? },
+};
arch/arm/mach-s5pv310/include/mach/map.h +16 -0
index f6a6587..d99eff3 100644
@@ -61,6 +61,22 @@
 
 ?#define S5PV310_PA_HSMMC(x) ? ? ? ? ? ?(0x12510000 + ((x) * 0x10000))
 
+/* S/PDIF */
+#define S5PV310_PA_SPDIF ? ? ? 0xE1100000
+
+/* I2S */
+#define S5PV310_PA_IIS0 ? ? ? ? ? ? ? ?0x03830000
+#define S5PV310_PA_IIS1 ? ? ? ? ? ? ? ?0xE3100000
+#define S5PV310_PA_IIS2 ? ? ? ? ? ? ? ?0xE2A00000
+
+/* PCM */
+#define S5PV310_PA_PCM0 ? ? ? ? ? ? ? ?0x03840000
+#define S5PV310_PA_PCM1 ? ? ? ? ? ? ? ?0x13980000
+#define S5PV310_PA_PCM2 ? ? ? ? ? ? ? ?0x13990000
+
+/* AC97 */
+#define S5PV310_PA_AC97 ? ? ? ? ? ? ? ?0x139A0000
+
 ?#define S5PV310_PA_UART ? ? ? ? ? ? ? ? ? ? ? ?(0x13800000)
 
 ?#define S5P_PA_UART(x) ? ? ? ? ? ? ? ? (S5PV310_PA_UART + ((x) * S3C_UART_OFFSET))
arch/arm/plat-samsung/include/plat/devs.h +0 -0
index 16521cc..9764268 100644
@@ -94,6 +94,15 @@ extern struct platform_device s5pv210_device_iis1;
 ?extern struct platform_device s5pv210_device_iis2;
 ?extern struct platform_device s5pv210_device_spdif;

arch/arm/plat-samsung/include/plat/devs.h extern struct platform_device s5pv210_device_iis1; · line 105

Quoted 10 lines
arch/arm/plat-samsung/include/plat/devs.h +9 -0
 
+extern struct platform_device s5pv310_device_ac97;
+extern struct platform_device s5pv310_device_pcm0;
+extern struct platform_device s5pv310_device_pcm1;
+extern struct platform_device s5pv310_device_pcm2;
+extern struct platform_device s5pv310_device_iis0;
+extern struct platform_device s5pv310_device_iis1;
+extern struct platform_device s5pv310_device_iis2;
+extern struct platform_device s5pv310_device_spdif;
+

How to make common audio platform data? If not, we should list all samsung soc audio node in the future.

Quoted 12 lines
arch/arm/plat-samsung/include/plat/devs.h +0 -1
 ?extern struct platform_device s5p6442_device_pcm0;
 ?extern struct platform_device s5p6442_device_pcm1;
 ?extern struct platform_device s5p6442_device_iis0;
--

1.6.2.5

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel at lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

author
#2 lore raw

PATCH 9/9 ARM: S5PV310: Add audio platform devices

Quoted 20 lines · Kyungmin Park
Quoted 19 lines · Jassi Brar

From: Jassi Brar <[email protected]>

Define platform devices for all audio devices found on S5PV310

---

?arch/arm/mach-s5pv310/Makefile ? ? ? ? ? ?| ? ?1 +
?arch/arm/mach-s5pv310/dev-audio.c ? ? ? ? | ?364 +++++++++++++++++++++++++++++
?arch/arm/mach-s5pv310/include/mach/map.h ?| ? 16 ++
?arch/arm/plat-samsung/include/plat/devs.h | ? ?9 +

?4 files changed, 390 insertions(+), 0 deletions(-) ?create mode 100644 arch/arm/mach-s5pv310/dev-audio.c

arch/arm/mach-s5pv310/Makefile +0 -0
index d265adb..61e3cb6 100644
@@ -27,6 +27,7 @@ obj-$(CONFIG_MACH_UNIVERSAL_C210) ? ? += mach-universal_c210.o
 
Quoted 4 lines
Quoted 3 lines

?# device support

+obj-y += dev-audio.o

Why it's default build? could you make a config as others?

It was decided by Ben (and Mark IIRC) that most, if not all, devices use audio and it is better to have the platform support built unconditionally. If you see, it is same for all platforms since 64xx.

Quoted 10 lines

arch/arm/mach-s5pv310/Makefile

Quoted 6 lines
arch/arm/mach-s5pv310/Makefile +6 -0
+static int s5pv310_cfg_i2s(struct platform_device *pdev)
+{
+ ? ? ? /* configure GPIO for i2s port */
+ ? ? ? switch (pdev->id) {
+ ? ? ? case 0:
+ ? ? ? ? ? ? ? s3c_gpio_cfgpin_range(S5PV310_GPZ(0), 7, S3C_GPIO_SFN(2));

Does it default setup for i2s? In my board some pins are used for other purpose.
I mean GPZ(1, 5, 6) doesn't used it for I2S.
then how do you handle this one?

At least in the manual that I have, I2S0 is possible only on GPZ[0:6], so if a user
does attempt to use I2S0, he/she shouldn't touch the GPIOs for any other purpose.
Please let me know details of your board if you think there is some problem with this setup.

Quoted 4 lines

arch/arm/mach-s5pv310/Makefile

Quoted 2 lines
arch/arm/mach-s5pv310/Makefile +2 -0
+
+static struct resource s5pv310_iis0_resource[] = {

You wrote that there are some users to use iis but c210/v310 doesn't. So you should use the i2s at least c210/v310 series

yes, this was simply modified from v210 so left unchanged.

Quoted 13 lines

arch/arm/mach-s5pv310/Makefile

Quoted 10 lines
arch/arm/mach-s5pv310/Makefile +9 -0
+extern struct platform_device s5pv310_device_ac97;
+extern struct platform_device s5pv310_device_pcm0;
+extern struct platform_device s5pv310_device_pcm1;
+extern struct platform_device s5pv310_device_pcm2;
+extern struct platform_device s5pv310_device_iis0;
+extern struct platform_device s5pv310_device_iis1;
+extern struct platform_device s5pv310_device_iis2;
+extern struct platform_device s5pv310_device_spdif;
+

How to make common audio platform data? If not, we should list all samsung soc audio node in the future.

That will be done when we have some common mechanism for all devices. There is nothing Audio specific that we can do about it.

#3 lore raw

PATCH 9/9 ARM: S5PV310: Add audio platform devices

Quoted 40 lines · Jassi Brar
Quoted 20 lines · Kyungmin Park
Quoted 19 lines · Jassi Brar

From: Jassi Brar <[email protected]>

Define platform devices for all audio devices found on S5PV310

---

?arch/arm/mach-s5pv310/Makefile ? ? ? ? ? ?| ? ?1 +
?arch/arm/mach-s5pv310/dev-audio.c ? ? ? ? | ?364 +++++++++++++++++++++++++++++
?arch/arm/mach-s5pv310/include/mach/map.h ?| ? 16 ++
?arch/arm/plat-samsung/include/plat/devs.h | ? ?9 +

?4 files changed, 390 insertions(+), 0 deletions(-) ?create mode 100644 arch/arm/mach-s5pv310/dev-audio.c

arch/arm/mach-s5pv310/Makefile +0 -0
index d265adb..61e3cb6 100644
@@ -27,6 +27,7 @@ obj-$(CONFIG_MACH_UNIVERSAL_C210) ? ? += mach-universal_c210.o
 
Quoted 4 lines
Quoted 3 lines

?# device support

+obj-y += dev-audio.o

Why it's default build? could you make a config as others?

It was decided by Ben (and Mark IIRC) that most, if not all, devices use audio and it is better to have the platform support built unconditionally. If you see, it is same for all platforms since 64xx.

Quoted 10 lines

arch/arm/mach-s5pv310/Makefile

Quoted 6 lines
arch/arm/mach-s5pv310/Makefile +6 -0
+static int s5pv310_cfg_i2s(struct platform_device *pdev)
+{
+ ? ? ? /* configure GPIO for i2s port */
+ ? ? ? switch (pdev->id) {
+ ? ? ? case 0:
+ ? ? ? ? ? ? ? s3c_gpio_cfgpin_range(S5PV310_GPZ(0), 7, S3C_GPIO_SFN(2));

Does it default setup for i2s? In my board some pins are used for other purpose.
I mean GPZ(1, 5, 6) doesn't used it for I2S.
then how do you handle this one?

Quoted 4 lines

At least in the manual that I have, I2S0 is possible only on GPZ[0:6], so if a user
does attempt to use I2S0, he/she shouldn't touch the GPIOs for any other purpose.

No C110 use the same scheme. and works

Quoted 2 lines

Please let me know details of your board if you think there is some problem with this setup.

As above it doesn't use the GPZ(1,5,6) and used for other purpose. and these are already checked by LSI H/W team.

Quoted 24 lines
Quoted 5 lines

arch/arm/mach-s5pv310/Makefile

Quoted 3 lines
arch/arm/mach-s5pv310/Makefile +2 -0
+
+static struct resource s5pv310_iis0_resource[] = {

You wrote that there are some users to use iis but c210/v310 doesn't. So you should use the i2s at least c210/v310 series

yes, this was simply modified from v210 so left unchanged.

Quoted 13 lines

arch/arm/mach-s5pv310/Makefile

Quoted 10 lines
arch/arm/mach-s5pv310/Makefile +9 -0
+extern struct platform_device s5pv310_device_ac97;
+extern struct platform_device s5pv310_device_pcm0;
+extern struct platform_device s5pv310_device_pcm1;
+extern struct platform_device s5pv310_device_pcm2;
+extern struct platform_device s5pv310_device_iis0;
+extern struct platform_device s5pv310_device_iis1;
+extern struct platform_device s5pv310_device_iis2;
+extern struct platform_device s5pv310_device_spdif;
+

How to make common audio platform data? If not, we should list all samsung soc audio node in the future.

That will be done when we have some common mechanism for all devices. There is nothing Audio specific that we can do about it.

author
#4 lore raw

PATCH 9/9 ARM: S5PV310: Add audio platform devices

Quoted 14 lines · Kyungmin Park
Quoted 10 lines
Quoted 10 lines

Review

Quoted 6 lines
(quoted diff) +6 -0
+static int s5pv310_cfg_i2s(struct platform_device *pdev)
+{
+ ? ? ? /* configure GPIO for i2s port */
+ ? ? ? switch (pdev->id) {
+ ? ? ? case 0:
+ ? ? ? ? ? ? ? s3c_gpio_cfgpin_range(S5PV310_GPZ(0), 7, S3C_GPIO_SFN(2));

Does it default setup for i2s? In my board some pins are used for other purpose.
I mean GPZ(1, 5, 6) doesn't used it for I2S.
then how do you handle this one?

Quoted 4 lines

At least in the manual that I have, I2S0 is possible only on GPZ[0:6], so if a user
does attempt to use I2S0, he/she shouldn't touch the GPIOs for any other purpose.

Quoted 5 lines

No C110 use the same scheme. and works

Quoted 2 lines

Please let me know details of your board if you think there is some problem with this setup.

As above it doesn't use the GPZ(1,5,6) and used for other purpose. and these are already checked by LSI H/W team.

Ok, so you mean running I2S0 in 2channel, rather than 6 channel mode. We don't support that yet but that should be easy to implement by defining custom i/f between platform and machine init code.