wl1251 SDIO patches
cover wl1251 SDIO patches
These patches add runtime PM support for wl1251, similar to how it's done for wl1271. This allows powering down the card properly when the driver is loaded but not started.
Last patch switches to cleaner method for passing platform_data. Most of this code is based on Ohad Ben-Cohen's wl1271 work.
Grazvydas Ignotas (3):
wl1251: add power callback to wl1251_if_operations
wl1251: add runtime PM support for SDIO
wl1251: use wl12xx_platform_data to pass data
arch/arm/mach-omap2/board-omap3pandora.c | 32 +++------- drivers/net/wireless/wl1251/main.c | 15 +++-- drivers/net/wireless/wl1251/sdio.c | 99 +++++++++++++++++++----------- drivers/net/wireless/wl1251/spi.c | 9 +++ drivers/net/wireless/wl1251/wl1251.h | 1 + drivers/net/wireless/wl12xx/Kconfig | 2 +- 6 files changed, 93 insertions(+), 65 deletions(-)
PATCH 1/3 wl1251: add power callback to wl1251_if_operations
Call interface specific power callback before calling board specific one. Also allow that callback to fail. This is how it's done for wl1271 and will be used for runtime_pm support.
--- drivers/net/wireless/wl1251/main.c | 15 +++++++++------ drivers/net/wireless/wl1251/sdio.c | 8 ++++++-- drivers/net/wireless/wl1251/spi.c | 9 +++++++++ drivers/net/wireless/wl1251/wl1251.h | 1 + 4 files changed, 25 insertions(+), 8 deletions(-)
drivers/net/wireless/wl1251/main.c +9 -6
@@ -52,14 +52,14 @@ void wl1251_disable_interrupts(struct wl1251 *wl) wl->if_ops->disable_irq (wl); } -static void wl1251_power_off (struct wl1251 *wl) +static int wl1251_power_off (struct wl1251 *wl) { - wl->set_power (false); +return wl->if_ops->power (wl, false); } -static void wl1251_power_on (struct wl1251 *wl) +static int wl1251_power_on (struct wl1251 *wl) { - wl->set_power (true); +return wl->if_ops->power (wl, true); }static int wl1251_fetch_firmware (struct wl1251 *wl)
@@ -152,9 +152,12 @@ static void wl1251_fw_wakeup(struct wl1251 *wl)static int wl1251_chip_wakeup (struct wl1251 *wl) { -int ret =0 ; +int ret; + + ret =wl1251_power_on (wl); +if (ret <0 ) +return ret; -wl1251_power_on (wl);msleep (WL1251_POWER_ON_SLEEP ); wl->if_ops->reset (wl);
drivers/net/wireless/wl1251/sdio.c +6 -2
@@ -171,8 +171,12 @@ static void wl1251_disable_line_irq(struct wl1251 *wl)return disable_irq (wl->irq); } -static void wl1251_sdio_set_power (bool enable) +static int wl1251_sdio_set_power (struct wl1251 *wl,bool enable) { +if (wl->set_power) + wl->set_power (enable); + +return 0 ; }static struct wl1251_if_operations wl1251_sdio_ops = {
@@ -181,6 +185,7 @@ static struct wl1251_if_operations wl1251_sdio_ops = { .write_elp = wl1251_sdio_write_elp, .read_elp = wl1251_sdio_read_elp, .reset = wl1251_sdio_reset, + .power = wl1251_sdio_set_power, };static int wl1251_platform_probe (struct platform_device *pdev)
@@ -239,7 +244,6 @@ static int wl1251_sdio_probe(struct sdio_func *func, wl_sdio->func = func; wl->if_priv = wl_sdio; wl->if_ops = &wl1251_sdio_ops; - wl->set_power = wl1251_sdio_set_power;if (wl12xx_board_data !=NULL ) { wl->set_power = wl12xx_board_data->set_power;
drivers/net/wireless/wl1251/spi.c +9 -0
@@ -215,12 +215,21 @@ static void wl1251_spi_disable_irq(struct wl1251 *wl)return disable_irq (wl->irq); } +static int wl1251_spi_set_power (struct wl1251 *wl,bool enable) +{ +if (wl->set_power) + wl->set_power (enable); + +return 0 ; +} +static const struct wl1251_if_operations wl1251_spi_ops = { .read = wl1251_spi_read, .write = wl1251_spi_write, .reset = wl1251_spi_reset_wake, .enable_irq = wl1251_spi_enable_irq, .disable_irq = wl1251_spi_disable_irq, + .power = wl1251_spi_set_power, };static int __devinit wl1251_spi_probe (struct spi_device *spi)
drivers/net/wireless/wl1251/wl1251.h +1 -0
@@ -256,6 +256,7 @@ struct wl1251_if_operations {void (*write)(struct wl1251 *wl,int addr,void *buf,size_t len);void (*read_elp)(struct wl1251 *wl,int addr,u32 *val);void (*write_elp)(struct wl1251 *wl,int addr,u32 val); +int (*power)(struct wl1251 *wl,bool enable);void (*reset)(struct wl1251 *wl);void (*enable_irq)(struct wl1251 *wl);void (*disable_irq)(struct wl1251 *wl);
Signature · 1 line
1.6.3.3
Re: [PATCH 1/3] wl1251: add power callback to wl1251_if_operations
Quoted 3 lines · Grazvydas Ignotas
Call interface specific power callback before calling board specific one. Also allow that callback to fail. This is how it's done for wl1271 and will be used for
runtime_pmsupport.
Thanks, looks good to me.
Quoted 1 line
Signed-off-by Grazvydas Ignotas <[email protected]>
Signature · 1 line
Kalle Valo
PATCH 2/3 wl1251: add runtime PM support for SDIO
In reply to Grazvydas IgnotasAdd runtime PM support, similar to how it's done for wl1271. This allows to power down the card when the driver is loaded but network is not in use.
--- drivers/net/wireless/wl1251/sdio.c | 62 ++++++++++++++++++++++++++++++++++-- 1 files changed, 59 insertions(+), 3 deletions(-)
drivers/net/wireless/wl1251/sdio.c +59 -3
@@ -26,6 +26,7 @@#include <linux/platform_device.h> #include <linux/wl12xx.h> #include <linux/irq.h> +#include <linux/pm_runtime.h> #include "wl1251.h"
@@ -173,10 +174,36 @@ static void wl1251_disable_line_irq(struct wl1251 *wl)static int wl1251_sdio_set_power (struct wl1251 *wl,bool enable) { -if (wl->set_power) - wl->set_power (enable); +struct sdio_func *func =wl_to_func (wl); +int ret; -return 0 ; +if (enable) { +/* Power up the card */ +if (wl->set_power) + wl->set_power (true); + + ret =pm_runtime_get_sync (&func->dev); +if (ret <0 ) + goto out; + +sdio_claim_host (func); +sdio_enable_func (func); +sdio_release_host (func); + }else { +sdio_claim_host (func); +sdio_disable_func (func); +sdio_release_host (func); + + ret =pm_runtime_put_sync (&func->dev); +if (ret <0 ) + goto out; + +if (wl->set_power) + wl->set_power (false); + } + +out: +return ret; }static struct wl1251_if_operations wl1251_sdio_ops = {
@@ -277,6 +304,10 @@ static int wl1251_sdio_probe(struct sdio_func *func, goto out_free_irq;sdio_set_drvdata (func, wl); + +/* Tell PM core that we don't need the card to be powered now */ +pm_runtime_put_noidle (&func->dev); +return ret; out_free_irq:
@@ -298,6 +329,9 @@ static void __devexit wl1251_sdio_remove(struct sdio_func *func)struct wl1251 *wl =sdio_get_drvdata (func);struct wl1251_sdio *wl_sdio = wl->if_priv; +/* Undo decrement done above in wl1271_probe */ +pm_runtime_get_noresume (&func->dev); +if (wl->irq)free_irq (wl->irq, wl);kfree (wl_sdio);
@@ -309,11 +343,33 @@ static void __devexit wl1251_sdio_remove(struct sdio_func *func)sdio_release_host (func); } +static int wl1251_suspend (struct device *dev) +{ +/* +* Tell MMC/SDIO core it's OK to power down the card +* (if it isn't already), but not to remove it completely +*/ +return 0 ; +} + +static int wl1251_resume (struct device *dev) +{ +return 0 ; +} + +static const struct dev_pm_ops wl1251_sdio_pm_ops = { + .suspend = wl1251_suspend, + .resume = wl1251_resume, +}; +static struct sdio_driver wl1251_sdio_driver = { .name ="wl1251_sdio" , .id_table = wl1251_devices, .probe = wl1251_sdio_probe, .remove =__devexit_p (wl1251_sdio_remove), + .drv = { + .pm = &wl1251_sdio_pm_ops, + }, };static int __init wl1251_sdio_init (void )
Signature · 1 line
1.6.3.3
Re: [PATCH 2/3] wl1251: add runtime PM support for SDIO
Quoted 26 lines · Grazvydas Ignotas
Add runtime PM support, similar to how it's done for wl1271. This allows to power down the card when the driver is loaded but network is not in use.
CC Ohad Ben-Cohen <[email protected]>Signed-off-by Grazvydas Ignotas <[email protected]>---
drivers/net/wireless/wl1251/sdio.c | 62 ++++++++++++++++++++++++++++++++++--1 files changed, 59 insertions(+), 3 deletions(-)drivers/net/wireless/wl1251/sdio.c +1
-0@@ -26,6 +26,7 @@ #include <linux/platform_device.h> #include <linux/wl12xx.h> #include <linux/irq.h> +#include <linux/pm_runtime.h> #include "wl1251.h"@@ -173,10 +174,36 @@ static void wl1251_disable_line_irq(struct wl1251 *wl) static int wl1251_sdio_set_power(struct wl1251 *wl, bool enable) {
drivers/net/wireless/wl1251/sdio.c static void wl1251_disable_line_irq(struct wl1251 *wl) · line 183
Quoted 10 lines
drivers/net/wireless/wl1251/sdio.c +6
-3- if (wl->set_power) - wl->set_power(enable); + struct sdio_func *func = wl_to_func(wl); + int ret; - return 0; + if (enable) { + /* Power up the card */ + if (wl->set_power) + wl->set_power(true);
Why do you still need that ->set_power() handler ?
drivers/net/wireless/wl1251/sdio.c static void wl1251_disable_line_irq(struct wl1251 *wl) · line 185
Quoted 2 lines
drivers/net/wireless/wl1251/sdio.c +2
-0+ + ret = pm_runtime_get_sync(&func->dev);
This call should do all the power-related work for you (assuming you have a fixed regulator in place).
Quoted 83 lines
drivers/net/wireless/wl1251/sdio.c +25
-0+ if (ret < 0) + goto out; + + sdio_claim_host(func); + sdio_enable_func(func); + sdio_release_host(func); + } else { + sdio_claim_host(func); + sdio_disable_func(func); + sdio_release_host(func); + + ret = pm_runtime_put_sync(&func->dev); + if (ret < 0) + goto out; + + if (wl->set_power) + wl->set_power(false); + } + +out: + return ret; } static struct wl1251_if_operations wl1251_sdio_ops = {@@ -277,6 +304,10 @@ static int wl1251_sdio_probe(struct sdio_func *func, goto out_free_irq; sdio_set_drvdata(func, wl); + + /* Tell PM core that we don't need the card to be powered now */ + pm_runtime_put_noidle(&func->dev); + return ret;out_free_irq:
drivers/net/wireless/wl1251/sdio.c +25
-1@@ -298,6 +329,9 @@ static void __devexit wl1251_sdio_remove(struct sdio_func *func) struct wl1251 *wl = sdio_get_drvdata(func); struct wl1251_sdio *wl_sdio = wl->if_priv; + /* Undo decrement done above in wl1271_probe */ + pm_runtime_get_noresume(&func->dev); + if (wl->irq) free_irq(wl->irq, wl); kfree(wl_sdio);@@ -309,11 +343,33 @@ static void __devexit wl1251_sdio_remove(struct sdio_func *func) sdio_release_host(func); } +static int wl1251_suspend (struct device *dev) +{ + /* + * Tell MMC/SDIO core it's OK to power down the card + * (if it isn't already), but not to remove it completely + */ + return 0; +} + +static int wl1251_resume (struct device *dev) +{ + return 0; +} + +static const struct dev_pm_ops wl1251_sdio_pm_ops = { + .suspend = wl1251_suspend, + .resume = wl1251_resume, +}; + static struct sdio_driver wl1251_sdio_driver = { .name = "wl1251_sdio", .id_table = wl1251_devices, .probe = wl1251_sdio_probe, .remove = __devexit_p(wl1251_sdio_remove), + .drv = { + .pm = &wl1251_sdio_pm_ops, + }, }; static int __init wl1251_sdio_init(void) --1.6.3.3
Re: [PATCH 2/3] wl1251: add runtime PM support for SDIO
Quoted 32 lines · Ohad Ben-Cohen
Quoted 31 lines · Grazvydas Ignotas
Add runtime PM support, similar to how it's done for wl1271. This allows to power down the card when the driver is loaded but network is not in use.
CC Ohad Ben-Cohen <[email protected]>Signed-off-by Grazvydas Ignotas <[email protected]>---
drivers/net/wireless/wl1251/sdio.c | 62 ++++++++++++++++++++++++++++++++++--1 files changed, 59 insertions(+), 3 deletions(-)drivers/net/wireless/wl1251/sdio.c +3
-2@@ -26,6 +26,7 @@ #include <linux/platform_device.h> #include <linux/wl12xx.h> #include <linux/irq.h> +#include <linux/pm_runtime.h> #include "wl1251.h"@@ -173,10 +174,36 @@ static void wl1251_disable_line_irq(struct wl1251 *wl) static int wl1251_sdio_set_power(struct wl1251 *wl, bool enable) { - if (wl->set_power) - wl->set_power(enable); + struct sdio_func *func = wl_to_func(wl); + int ret;
Quoted 7 lines
drivers/net/wireless/wl1251/sdio.c static void wl1251_disable_line_irq(struct wl1251 *wl) · line 183
Quoted 5 lines
drivers/net/wireless/wl1251/sdio.c +4
-1- return 0; + if (enable) { + /* Power up the card */ + if (wl->set_power) + wl->set_power(true);Why do you still need that ->set_power() handler ?
On pandora besides power, we also have a GPIO to control clock buffer for wl1251, so I thought I could enable it here. Perhaps it could be set up as regulator too, but I'm not sure how to set it up so that clock is enabled before main power. Also it's not really a power supply so it somehow felt wrong to set up regulator for it.
Re: [PATCH 2/3] wl1251: add runtime PM support for SDIO
Quoted 41 lines · Grazvydas Ignotas
Quoted 32 lines · Ohad Ben-Cohen
Quoted 31 lines · Grazvydas Ignotas
Add runtime PM support, similar to how it's done for wl1271. This allows to power down the card when the driver is loaded but network is not in use.
CC Ohad Ben-Cohen <[email protected]>Signed-off-by Grazvydas Ignotas <[email protected]>---
drivers/net/wireless/wl1251/sdio.c | 62 ++++++++++++++++++++++++++++++++++--1 files changed, 59 insertions(+), 3 deletions(-)drivers/net/wireless/wl1251/sdio.c +3
-2@@ -26,6 +26,7 @@ #include <linux/platform_device.h> #include <linux/wl12xx.h> #include <linux/irq.h> +#include <linux/pm_runtime.h> #include "wl1251.h"@@ -173,10 +174,36 @@ static void wl1251_disable_line_irq(struct wl1251 *wl) static int wl1251_sdio_set_power(struct wl1251 *wl, bool enable) { - if (wl->set_power) - wl->set_power(enable); + struct sdio_func *func = wl_to_func(wl); + int ret;Quoted 7 lines
drivers/net/wireless/wl1251/sdio.c static void wl1251_disable_line_irq(struct wl1251 *wl) · line 183
Quoted 5 lines
drivers/net/wireless/wl1251/sdio.c +4
-1- return 0; + if (enable) { + /* Power up the card */ + if (wl->set_power) + wl->set_power(true);Why do you still need that ->set_power() handler ?
Quoted 2 lines
On pandora besides power, we also have a GPIO to control clock buffer for wl1251, so I thought I could enable it here.
Oh, I see. The name set_power then is a bit misleading.. ;)
Quoted 5 lines
Perhaps it could be
set up as regulator too, but I'm not sure how to set it up so that clock is enabled before main power. Also it's not really a power supply so it somehow felt wrong to set up regulator for it.
Re: [PATCH 2/3] wl1251: add runtime PM support for SDIO
Quoted 6 lines · Ohad Ben-Cohen
Quoted 4 lines
Quoted 1 line
Why do you still need that ->set_power() handler ?
On pandora besides power, we also have a GPIO to control clock buffer for wl1251, so I thought I could enable it here.
Oh, I see. The name
set_powerthen is a bit misleading.. ;)
Maybe a comment stating the reason for the callback would make it more clear?
Signature · 1 line
Kalle Valo
Re: [PATCH 2/3] wl1251: add runtime PM support for SDIO
Quoted 2 lines · Kalle Valo
Maybe a comment stating the reason for the callback would make it more clear?
Definitely.
Quoted 4 lines
--
Kalle Valo
Re: [PATCH 2/3] wl1251: add runtime PM support for SDIO
In reply to Grazvydas IgnotasQuoted 3 lines · Grazvydas Ignotas
Add runtime PM support, similar to how it's done for wl1271. This allows to power down the card when the driver is loaded but network is not in use.
Few minor comments:
drivers/net/wireless/wl1251/sdio.c static void __devexit wl1251_sdio_remove(struct sdio_func *func) · line 332
Quoted 1 line
drivers/net/wireless/wl1251/sdio.c +1
-0+/* Undo decrement done above in wl1271_probe */
Should be wl1251_probe().
drivers/net/wireless/wl1251/sdio.c static void __devexit wl1251_sdio_remove(struct sdio_func *func) · line 353
Quoted 8 lines
drivers/net/wireless/wl1251/sdio.c +8
-0+static int wl1251_suspend (struct device *dev) +{ +/* +* Tell MMC/SDIO core it's OK to power down the card +* (if it isn't already), but not to remove it completely +*/ +return 0 ; +}
Sorry, I'm not familiar with pm_ops and I don't fully understand the comment above. Does the comment mean that by returning 0 we can accomplish all that? Or instead is it a fixme comment that we should do that, but it's not implemented yet?
Signature · 1 line
Kalle Valo
Re: [PATCH 2/3] wl1251: add runtime PM support for SDIO
Quoted 4 lines · Kalle Valo
Quoted 4 lines
drivers/net/wireless/wl1251/sdio.c +4
-0+static int wl1251_suspend (struct device *dev) +{ + /* +* Tell MMC/SDIO core it's OK to power down the card
Quoted 8 lines
Quoted 4 lines
+ * (if it isn't already), but not to remove it completely
+ */
+ return 0;
+}Sorry, I'm not familiar with
pm_opsand I don't fully understand the comment above. Does the comment mean that by returning 0 we can accomplish all that?
Yes. By returning 0 we let the MMC core power down our card, but not remove it.
Quoted 6 lines
Or instead is it a fixme comment that we should
do that, but it's not implemented yet?--
Kalle Valo
Re: [PATCH 2/3] wl1251: add runtime PM support for SDIO
Quoted 14 lines · Ohad Ben-Cohen
Quoted 4 lines · Kalle Valo
Quoted 4 lines
drivers/net/wireless/wl1251/sdio.c +4
-0+static int wl1251_suspend (struct device *dev) +{ + /* +* Tell MMC/SDIO core it's OK to power down the card Quoted 8 lines
Quoted 4 lines
+ * (if it isn't already), but not to remove it completely
+ */
+ return 0;
+}Sorry, I'm not familiar with
pm_opsand I don't fully understand the comment above. Does the comment mean that by returning 0 we can accomplish all that?
Quoted 2 lines
Yes. By returning 0 we let the MMC core power down our card, but not remove it.
Good, thanks for confirming that.
Signature · 1 line
Kalle Valo
Re: [PATCH 2/3] wl1251: add runtime PM support for SDIO
Quoted 16 lines · Kalle Valo
Quoted 14 lines · Ohad Ben-Cohen
Quoted 12 lines · Kalle Valo
drivers/net/wireless/wl1251/sdio.c static void __devexit wl1251_sdio_remove(struct sdio_func *func) · line 353
Quoted 8 lines
drivers/net/wireless/wl1251/sdio.c +8
-0+static int wl1251_suspend (struct device *dev) +{ + /* + * Tell MMC/SDIO core it's OK to power down the card + * (if it isn't already), but not to remove it completely + */ + return 0; +}Sorry, I'm not familiar with
pm_opsand I don't fully understand the comment above. Does the comment mean that by returning 0 we can accomplish all that?
Quoted 4 lines
Quoted 2 lines
Yes. By returning 0 we let the MMC core power down our card, but not remove it.
Good, thanks for confirming that.
Thanks, updating comments and resending this one in a moment.
PATCH 3/3 wl1251: use wl12xx_platform_data to pass data
In reply to Grazvydas IgnotasMake use the newly added method to pass platform data for wl1251 too. This allows to eliminate some redundant code.
---
This touches arch/arm/mach-omap2/* but I think it should go through the wireless tree to avoid cross-tree dependencies, if Tony and others are ok with this.
arch/arm/mach-omap2/board-omap3pandora.c | 32 +++++++------------------- drivers/net/wireless/wl1251/sdio.c | 35 +---------------------------- drivers/net/wireless/wl12xx/Kconfig | 2 +- 3 files changed, 12 insertions(+), 57 deletions(-)
arch/arm/mach-omap2/board-omap3pandora.c +9 -23
@@ -642,31 +642,13 @@ static void __init omap3pandora_init_irq(void)omap_gpio_init (); } -static void pandora_wl1251_set_power (bool enable) -{ -/* -* Keep power always on until wl1251_sdio driver learns to re-init -* the chip after powering it down and back up. -*/ -} - -static struct wl12xx_platform_data pandora_wl1251_pdata = { - .set_power = pandora_wl1251_set_power, - .use_eeprom = true, -}; - -static struct platform_device pandora_wl1251_data = { - .name ="wl1251_data" , - .id =-1 , - .dev = { - .platform_data = &pandora_wl1251_pdata, - }, -}; - -static void pandora_wl1251_init (void ) +static void __init pandora_wl1251_init (void ) { +struct wl12xx_platform_data pandora_wl1251_pdata;int ret; +memset (&pandora_wl1251_pdata,0 ,sizeof (pandora_wl1251_pdata)); + ret =gpio_request (PANDORA_WIFI_IRQ_GPIO ,"wl1251 irq" );if (ret <0 ) goto fail;
@@ -679,6 +661,11 @@ static void pandora_wl1251_init(void)if (pandora_wl1251_pdata.irq <0 ) goto fail_irq; + pandora_wl1251_pdata.use_eeprom = true; + ret =wl12xx_set_platform_data (&pandora_wl1251_pdata); +if (ret <0 ) + goto fail_irq; +return ; fail_irq:
@@ -691,7 +678,6 @@ static struct platform_device *omap3pandora_devices[] __initdata = { &pandora_leds_gpio, &pandora_keys_gpio, &pandora_dss_device, - &pandora_wl1251_data, &pandora_vwlan_device, };
drivers/net/wireless/wl1251/sdio.c +2 -33
@@ -43,8 +43,6 @@ struct wl1251_sdio {u32 elp_val; }; -static struct wl12xx_platform_data *wl12xx_board_data; -static struct sdio_func *wl_to_func (struct wl1251 *wl) {struct wl1251_sdio *wl_sdio = wl->if_priv;
@@ -215,30 +213,6 @@ static struct wl1251_if_operations wl1251_sdio_ops = { .power = wl1251_sdio_set_power, }; -static int wl1251_platform_probe (struct platform_device *pdev) -{ -if (pdev->id !=-1 ) { -wl1251_error ("can only handle single device" ); -return -ENODEV ; - } - - wl12xx_board_data = pdev->dev.platform_data; -return 0 ; -} - -/* -* Dummy platform_driver for passing platform_data to this driver, -* until we have a way to pass this through SDIO subsystem or -* some other way. -*/ -static struct platform_driver wl1251_platform_driver = { - .driver = { - .name ="wl1251_data" , - .owner =THIS_MODULE , - }, - .probe = wl1251_platform_probe, -}; -static int wl1251_sdio_probe (struct sdio_func *func,const struct sdio_device_id *id) {
@@ -246,6 +220,7 @@ static int wl1251_sdio_probe(struct sdio_func *func,struct wl1251 *wl;struct ieee80211_hw *hw;struct wl1251_sdio *wl_sdio; +const struct wl12xx_platform_data *wl12xx_board_data; hw =wl1251_alloc_hw ();if (IS_ERR (hw))
@@ -272,6 +247,7 @@ static int wl1251_sdio_probe(struct sdio_func *func, wl->if_priv = wl_sdio; wl->if_ops = &wl1251_sdio_ops; + wl12xx_board_data =wl12xx_get_platform_data ();if (wl12xx_board_data !=NULL ) { wl->set_power = wl12xx_board_data->set_power; wl->irq = wl12xx_board_data->irq;
@@ -376,12 +352,6 @@ static int __init wl1251_sdio_init(void) {int err; - err =platform_driver_register (&wl1251_platform_driver); -if (err) { -wl1251_error ("failed to register platform driver: %d" , err); -return err; - } - err =sdio_register_driver (&wl1251_sdio_driver);if (err)wl1251_error ("failed to register sdio driver: %d" , err);
@@ -391,7 +361,6 @@ static int __init wl1251_sdio_init(void) static void __exit wl1251_sdio_exit(void) {sdio_unregister_driver (&wl1251_sdio_driver); -platform_driver_unregister (&wl1251_platform_driver);wl1251_notice ("unloaded" ); }
drivers/net/wireless/wl12xx/Kconfig +1 -1
@@ -42,5 +42,5 @@ config WL1271_SDIO config WL12XX_PLATFORM_DATA bool - depends on WL1271_SDIO != n + depends on WL1271_SDIO != n || WL1251_SDIO != n default y
Signature · 1 line
1.6.3.3
Re: [PATCH 3/3] wl1251: use wl12xx_platform_data to pass data
Quoted 6 lines · Grazvydas Ignotas
Make use the newly added method to pass platform data for wl1251 too. This allows to eliminate some redundant code.
Cc Tony Lindgren <[email protected]>Cc Ohad Ben-Cohen <[email protected]>Signed-off-by Grazvydas Ignotas <[email protected]>
For the wl1251 part:
Quoted 4 lines
---
This touchesarch/arm/mach-omap2/*but I think it should go through the wireless tree to avoid cross-tree dependencies, if Tony and others are ok with this.
I agree, better to push this through the wireless tree.
Quoted 3 lines
arch/arm/mach-omap2/board-omap3pandora.c | 32 +++++++------------------- drivers/net/wireless/wl1251/sdio.c | 35 +---------------------------- drivers/net/wireless/wl12xx/Kconfig | 2 +-
We need to CC Luciano for the wl12xx change.
drivers/net/wireless/wl12xx/Kconfig config WL1271_SDIO · line 46
Quoted 9 lines
drivers/net/wireless/wl12xx/Kconfig +1
-1@@ -42,5 +42,5 @@ config WL1271_SDIO config WL12XX_PLATFORM_DATA bool - depends on WL1271_SDIO != n + depends on WL1271_SDIO != n || WL1251_SDIO != n default y
Oh, I didn't take this into account when I moved wl1251 out from the wl12xx directory. Now wl1251 has a dependency to wl12xx stuff.
Oh well, it's a small issue. I guess we can live with that :)
Signature · 1 line
Kalle Valo
Luciano Coelho
Acked-byRe: [PATCH 3/3] wl1251: use wl12xx_platform_data to pass data
Quoted 39 lines · ext Kalle Valo
Quoted 6 lines · Grazvydas Ignotas
Make use the newly added method to pass platform data for wl1251 too. This allows to eliminate some redundant code.
Cc Tony Lindgren <[email protected]>Cc Ohad Ben-Cohen <[email protected]>Signed-off-by Grazvydas Ignotas <[email protected]>For the wl1251 part:
Acked-by Kalle Valo <[email protected]>Quoted 4 lines
---
This touchesarch/arm/mach-omap2/*but I think it should go through the wireless tree to avoid cross-tree dependencies, if Tony and others are ok with this.I agree, better to push this through the wireless tree.
Quoted 3 lines
arch/arm/mach-omap2/board-omap3pandora.c | 32 +++++++------------------- drivers/net/wireless/wl1251/sdio.c | 35 +---------------------------- drivers/net/wireless/wl12xx/Kconfig | 2 +-We need to CC Luciano for the wl12xx change.
drivers/net/wireless/wl12xx/Kconfig config WL1271_SDIO · line 46
Quoted 9 lines
drivers/net/wireless/wl12xx/Kconfig +1
-1@@ -42,5 +42,5 @@ config WL1271_SDIO config WL12XX_PLATFORM_DATA bool - depends on WL1271_SDIO != n + depends on WL1271_SDIO != n || WL1251_SDIO != n default yOh, I didn't take this into account when I moved wl1251 out from the wl12xx directory. Now wl1251 has a dependency to wl12xx stuff.
Quoted 1 line
Oh well, it's a small issue. I guess we can live with that :)
Yeah, I didn't realize this either. I think we can live with that, but at some point we should clean this up and either have separate platform data for wl1251 and wl12xx or move the the platform data one level up, to wireless. But for now:
And I agree with pushing this through wireless-testing as well, if it's okay with Tony and John.
Signature · 2 lines
Cheers, Luca.
Re: [PATCH 3/3] wl1251: use wl12xx_platform_data to pass data
Quoted 47 lines · Luciano Coelho
Quoted 39 lines · ext Kalle Valo
Quoted 6 lines · Grazvydas Ignotas
Make use the newly added method to pass platform data for wl1251 too. This allows to eliminate some redundant code.
Cc Tony Lindgren <[email protected]>Cc Ohad Ben-Cohen <[email protected]>Signed-off-by Grazvydas Ignotas <[email protected]>For the wl1251 part:
Acked-by Kalle Valo <[email protected]>Quoted 4 lines
---
This touchesarch/arm/mach-omap2/*but I think it should go through the wireless tree to avoid cross-tree dependencies, if Tony and others are ok with this.I agree, better to push this through the wireless tree.
Quoted 3 lines
arch/arm/mach-omap2/board-omap3pandora.c | 32 +++++++------------------- drivers/net/wireless/wl1251/sdio.c | 35 +---------------------------- drivers/net/wireless/wl12xx/Kconfig | 2 +-We need to CC Luciano for the wl12xx change.
drivers/net/wireless/wl12xx/Kconfig config WL1271_SDIO · line 46
Quoted 9 lines
drivers/net/wireless/wl12xx/Kconfig +1
-1@@ -42,5 +42,5 @@ config WL1271_SDIO config WL12XX_PLATFORM_DATA bool - depends on WL1271_SDIO != n + depends on WL1271_SDIO != n || WL1251_SDIO != n default yOh, I didn't take this into account when I moved wl1251 out from the wl12xx directory. Now wl1251 has a dependency to wl12xx stuff.
Quoted 1 line
Oh well, it's a small issue. I guess we can live with that :)
Yeah, I didn't realize this either. I think we can live with that, but at some point we should clean this up and either have separate platform data for wl1251 and wl12xx or move the the platform data one level up, to wireless. But for now:
Quoted 4 lines
Acked-by Luciano Coelho <[email protected]>And I agree with pushing this through wireless-testing as well, if it's okay with Tony and John.
Yes, ack from me too: