Skip to contentSkip to conversation

Bluetooth: Automate remote name requests

PATCH In review [email protected] 2 participants 3 messages Oct 28, 2010 – Nov 10, 2010

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 Bluetooth: Automate remote name requests

From: Johan Hedberg <[email protected]>

In Bluetooth there are no automatic updates of remote device names when they get changed on the remote side. Instead, it is a good idea to do a manual name request when a new connection gets created (for whatever reason) since at this point it is very cheap (no costly baseband connection creation needed just for the sake of the name request).

So far userspace has been responsible for this extra name request but tighter control is needed in order not to flood Bluetooth controllers with two many commands during connection creation. It has been shown that some controllers simply fail to function correctly if they get too many (almost) simultaneous commands during connection creation. The simplest way to acheive better control of these commands is to move their sending completely to the kernel side.

This patch inserts name requests into the sequence of events that the kernel performs during connection creation. It does this after the remote features have been successfully requested and before any pending authentication requests are performed. The code will work sub-optimally with userspace versions that still do the name requesting themselves (it shouldn't break anything though) so it is recommended to combine this with a userspace software version that doesn't have automated name requests.

---
v2 makes sure that the name request gets always sent instead of just doing it for cases when we're also going to request authentication.

 net/bluetooth/hci_event.c |  151 ++++++++++++++++++++++++++++++++-------------
 1 files changed, 107 insertions(+), 44 deletions(-)
net/bluetooth/hci_event.c +107 -44
index 84093b0..6e770e8 100644
@@ -677,9 +677,51 @@ static void hci_cs_set_conn_encrypt(struct hci_dev *hdev, __u8 status)
 	hci_dev_unlock(hdev);
 }
 
+static void request_outgoing_auth(struct hci_dev *hdev, bdaddr_t *bdaddr)
+{
+	struct hci_cp_auth_requested cp;
+	struct hci_conn *conn;
+
+	conn = hci_conn_hash_lookup_ba(hdev, ACL_LINK, bdaddr);
+	if (!conn)
+		return;
+
+	if (conn->state != BT_CONFIG || !conn->out)
+		return;
+
+	if (conn->sec_level == BT_SECURITY_SDP)
+		return;
+
+	/* Only request authentication for SSP connections or non-SSP
+	 * devices with sec_level HIGH */
+	if (!(hdev->ssp_mode > 0 && conn->ssp_mode > 0) &&
+					conn->sec_level != BT_SECURITY_HIGH)
+		return;
+
+	cp.handle = __cpu_to_le16(conn->handle);
+	hci_send_cmd(hdev, HCI_OP_AUTH_REQUESTED, sizeof(cp), &cp);
+}
+
 static void hci_cs_remote_name_req(struct hci_dev *hdev, __u8 status)
 {
+	struct hci_cp_remote_name_req *cp;
+
 	BT_DBG("%s status 0x%x", hdev->name, status);
+
+	/* If successful wait for the name req complete event before
+	 * checking for the need to do authentication */
+	if (!status)
+		return;
+
+	cp = hci_sent_cmd_data(hdev, HCI_OP_REMOTE_NAME_REQ);
+	if (!cp)
+		return;
+
+	hci_dev_lock(hdev);
+
+	request_outgoing_auth(hdev, &cp->bdaddr);
+
+	hci_dev_unlock(hdev);
 }
 
 static void hci_cs_read_remote_features(struct hci_dev *hdev, __u8 status)
@@ -1090,9 +1132,17 @@ static inline void hci_auth_complete_evt(struct hci_dev *hdev, struct sk_buff *s
 
 static inline void hci_remote_name_evt(struct hci_dev *hdev, struct sk_buff *skb)
 {
+	struct hci_ev_remote_name *ev = (void *) skb->data;
+
 	BT_DBG("%s", hdev->name);
 
 	hci_conn_check_pending(hdev);
+
+	hci_dev_lock(hdev);
+
+	request_outgoing_auth(hdev, &ev->bdaddr);
+
+	hci_dev_unlock(hdev);
 }
 
 static inline void hci_encrypt_change_evt(struct hci_dev *hdev, struct sk_buff *skb)
@@ -1162,33 +1212,39 @@ static inline void hci_remote_features_evt(struct hci_dev *hdev, struct sk_buff
 	hci_dev_lock(hdev);
 
 	conn = hci_conn_hash_lookup_handle(hdev, __le16_to_cpu(ev->handle));
-	if (conn) {
-		if (!ev->status)
-			memcpy(conn->features, ev->features, 8);
+	if (!conn)
+		goto unlock;
 
-		if (conn->state == BT_CONFIG) {
-			if (!ev->status && lmp_ssp_capable(hdev) &&
-						lmp_ssp_capable(conn)) {
-				struct hci_cp_read_remote_ext_features cp;
-				cp.handle = ev->handle;
-				cp.page = 0x01;
-				hci_send_cmd(hdev,
-					HCI_OP_READ_REMOTE_EXT_FEATURES,
-							sizeof(cp), &cp);
-			} else if (!ev->status && conn->out &&
-					conn->sec_level == BT_SECURITY_HIGH) {
-				struct hci_cp_auth_requested cp;
-				cp.handle = ev->handle;
-				hci_send_cmd(hdev, HCI_OP_AUTH_REQUESTED,
+	if (!ev->status)
+		memcpy(conn->features, ev->features, 8);
+
+	if (conn->state != BT_CONFIG)
+		goto unlock;
+
+	if (!ev->status && lmp_ssp_capable(hdev) && lmp_ssp_capable(conn)) {
+		struct hci_cp_read_remote_ext_features cp;
+		cp.handle = ev->handle;
+		cp.page = 0x01;
+		hci_send_cmd(hdev, HCI_OP_READ_REMOTE_EXT_FEATURES,
 							sizeof(cp), &cp);
-			} else {
-				conn->state = BT_CONNECTED;
-				hci_proto_connect_cfm(conn, ev->status);
-				hci_conn_put(conn);
-			}
-		}
+		goto unlock;
+	}
+
+	if (!ev->status) {
+		struct hci_cp_remote_name_req cp;
+		memset(&cp, 0, sizeof(cp));
+		bacpy(&cp.bdaddr, &conn->dst);
+		cp.pscan_rep_mode = 0x02;
+		hci_send_cmd(hdev, HCI_OP_REMOTE_NAME_REQ, sizeof(cp), &cp);
+	}
+
+	if (!conn->out || conn->sec_level != BT_SECURITY_HIGH) {
+		conn->state = BT_CONNECTED;
+		hci_proto_connect_cfm(conn, ev->status);
+		hci_conn_put(conn);
 	}
 
+unlock:
 	hci_dev_unlock(hdev);
 }
 
@@ -1646,32 +1702,39 @@ static inline void hci_remote_ext_features_evt(struct hci_dev *hdev, struct sk_b
 	hci_dev_lock(hdev);
 
 	conn = hci_conn_hash_lookup_handle(hdev, __le16_to_cpu(ev->handle));
-	if (conn) {
-		if (!ev->status && ev->page == 0x01) {
-			struct inquiry_entry *ie;
+	if (!conn)
+		goto unlock;
 
-			if ((ie = hci_inquiry_cache_lookup(hdev, &conn->dst)))
-				ie->data.ssp_mode = (ev->features[0] & 0x01);
+	if (!ev->status && ev->page == 0x01) {
+		struct inquiry_entry *ie;
 
-			conn->ssp_mode = (ev->features[0] & 0x01);
-		}
+		if ((ie = hci_inquiry_cache_lookup(hdev, &conn->dst)))
+			ie->data.ssp_mode = (ev->features[0] & 0x01);
 
-		if (conn->state == BT_CONFIG) {
-			if (!ev->status && hdev->ssp_mode > 0 &&
-					conn->ssp_mode > 0 && conn->out &&
-					conn->sec_level != BT_SECURITY_SDP) {
-				struct hci_cp_auth_requested cp;
-				cp.handle = ev->handle;
-				hci_send_cmd(hdev, HCI_OP_AUTH_REQUESTED,
-							sizeof(cp), &cp);
-			} else {
-				conn->state = BT_CONNECTED;
-				hci_proto_connect_cfm(conn, ev->status);
-				hci_conn_put(conn);
-			}
-		}
+		conn->ssp_mode = (ev->features[0] & 0x01);
 	}
 
+	if (conn->state != BT_CONFIG)
+		goto unlock;
+
+	if (!ev->status) {
+		struct hci_cp_remote_name_req cp;
+		memset(&cp, 0, sizeof(cp));
+		bacpy(&cp.bdaddr, &conn->dst);
+		cp.pscan_rep_mode = 0x02;
+		hci_send_cmd(hdev, HCI_OP_REMOTE_NAME_REQ, sizeof(cp), &cp);
+	}
+
+	/* If legacy pairing, or an incoming connection, or SDP security
+	 * consider ourself connected */
+	if (!(hdev->ssp_mode > 0 && conn->ssp_mode > 0) || !conn->out ||
+					conn->sec_level == BT_SECURITY_SDP) {
+		conn->state = BT_CONNECTED;
+		hci_proto_connect_cfm(conn, ev->status);
+		hci_conn_put(conn);
+	}
+
+unlock:
 	hci_dev_unlock(hdev);
 }
 
Signature · 1 line
1.7.1
maintainer
#1 lore raw

Hi Johan,

Quoted 53 lines

In Bluetooth there are no automatic updates of remote device names when they get changed on the remote side. Instead, it is a good idea to do a manual name request when a new connection gets created (for whatever reason) since at this point it is very cheap (no costly baseband connection creation needed just for the sake of the name request).

So far userspace has been responsible for this extra name request but tighter control is needed in order not to flood Bluetooth controllers with two many commands during connection creation. It has been shown that some controllers simply fail to function correctly if they get too many (almost) simultaneous commands during connection creation. The simplest way to acheive better control of these commands is to move their sending completely to the kernel side.

This patch inserts name requests into the sequence of events that the kernel performs during connection creation. It does this after the remote features have been successfully requested and before any pending authentication requests are performed. The code will work sub-optimally with userspace versions that still do the name requesting themselves (it shouldn't break anything though) so it is recommended to combine this with a userspace software version that doesn't have automated name requests.

---
v2 makes sure that the name request gets always sent instead of just doing it for cases when we're also going to request authentication.

 net/bluetooth/hci_event.c |  151 ++++++++++++++++++++++++++++++++-------------
 1 files changed, 107 insertions(+), 44 deletions(-)
net/bluetooth/hci_event.c +14 -0
index 84093b0..6e770e8 100644
@@ -677,9 +677,51 @@ static void hci_cs_set_conn_encrypt(struct hci_dev *hdev, __u8 status)
 	hci_dev_unlock(hdev);
 }
 
+static void request_outgoing_auth(struct hci_dev *hdev, bdaddr_t *bdaddr)
+{
+	struct hci_cp_auth_requested cp;
+	struct hci_conn *conn;
+
+	conn = hci_conn_hash_lookup_ba(hdev, ACL_LINK, bdaddr);
+	if (!conn)
+		return;
+
+	if (conn->state != BT_CONFIG || !conn->out)
+		return;
+
+	if (conn->sec_level == BT_SECURITY_SDP)
+		return;

net/bluetooth/hci_event.c static void hci_cs_set_conn_encrypt(struct hci_dev *hdev, __u8 status) · line 703

Quoted 10 lines
net/bluetooth/hci_event.c +10 -0
+
+	/* Only request authentication for SSP connections or non-SSP
+	 * devices with sec_level HIGH */
+	if (!(hdev->ssp_mode > 0 && conn->ssp_mode > 0) &&
+					conn->sec_level != BT_SECURITY_HIGH)
+		return;
+
+	cp.handle = __cpu_to_le16(conn->handle);
+	hci_send_cmd(hdev, HCI_OP_AUTH_REQUESTED, sizeof(cp), &cp);
+}

please split this patch into two. One creating the common function for the authentication requested and one for adding the name request.

My brain actually core dumps when following the logic and making sure that it is still correct. I pretty sure it is correct, but the whole patch is damn hard to review.

Regards

Marcel

#2 lore raw

Hi Marcel,

Quoted 6 lines · Marcel Holtmann

please split this patch into two. One creating the common function for the authentication requested and one for adding the name request.

My brain actually core dumps when following the logic and making sure that it is still correct. I pretty sure it is correct, but the whole patch is damn hard to review.

Yeah, sorry about this. I know the patch ended up being quite complex. I'll resend it in three parts in a moment:

1. getting rid of multiple nested if-statements in the remote features callbacks.
2. create a unified authentication request function
3. add the remote name request

Johan