davinci: EMAC support for Omapl138-Hawkboard
Subsystems (5)
A message that is not in the archive (sent off-list or not yet received): [email protected]
PATCH v8 1/9 davinci: EMAC support for Omapl138-Hawkboard
From: Victor Rodriguez <[email protected]>
This patch adds EMAC support for the Hawkboard-L138 system
--- arch/arm/mach-davinci/board-omapl138-hawk.c | 43 +++++++++++++++++++++++++++ 1 files changed, 43 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-omapl138-hawk.c +43 -0
@@ -19,6 +19,47 @@#include <mach/cp_intc.h> #include <mach/da8xx.h> +#include <mach/mux.h> + +#define HAWKBOARD_PHY_ID "0:07" + +static short omapl138_hawk_mii_pins[]__initdata = { +DA850_MII_TXEN ,DA850_MII_TXCLK ,DA850_MII_COL ,DA850_MII_TXD_3 , +DA850_MII_TXD_2 ,DA850_MII_TXD_1 ,DA850_MII_TXD_0 ,DA850_MII_RXER , +DA850_MII_CRS ,DA850_MII_RXCLK ,DA850_MII_RXDV ,DA850_MII_RXD_3 , +DA850_MII_RXD_2 ,DA850_MII_RXD_1 ,DA850_MII_RXD_0 ,DA850_MDIO_CLK , +DA850_MDIO_D , +-1 +}; + +static __init void omapl138_hawk_config_emac (void ) +{ +void __iomem *cfgchip3 =DA8XX_SYSCFG0_VIRT (DA8XX_CFGCHIP3_REG ); +int ret; +u32 val; +struct davinci_soc_info *soc_info = &davinci_soc_info; + + val =__raw_readl (cfgchip3); + val &= ~BIT (8 ); + ret =davinci_cfg_reg_list (omapl138_hawk_mii_pins); +if (ret) { +pr_warning ("%s: cpgmac/mii mux setup failed: %d\n" , + __func__, ret); +return ; + } + +/* configure the CFGCHIP3 register for MII */ +__raw_writel (val, cfgchip3); +pr_info ("EMAC: MII PHY configured\n" ); + + soc_info->emac_pdata->phy_id =HAWKBOARD_PHY_ID ; + + ret =da8xx_register_emac (); +if (ret) +pr_warning ("%s: emac registration failed: %d\n" , + __func__, ret); +} +static struct davinci_uart_config omapl138_hawk_uart_config__initdata = { .enabled_uarts =0x7 ,
@@ -30,6 +71,8 @@ static __init void omapl138_hawk_init(void)davinci_serial_init (&omapl138_hawk_uart_config); +omapl138_hawk_config_emac (); + ret =da8xx_register_watchdog ();if (ret) pr_warning("omapl138_hawk_init: "
Signature · 1 line
1.7.0.4
PATCH v8 2/9 davinci: EDMA support for Omapl138-Hawkboard
In reply to a message not in the archiveFrom: Victor Rodriguez <[email protected]>
This patch adds EDMA support for the Hawkboard-L138 system
--- arch/arm/mach-davinci/board-omapl138-hawk.c | 54 +++++++++++++++++++++++++++ 1 files changed, 54 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-omapl138-hawk.c +54 -0
@@ -60,6 +60,55 @@ static __init void omapl138_hawk_config_emac(void) __func__, ret); } +/* +* The following EDMA channels/slots are not being used by drivers (for +* example: Timer, GPIO, UART events etc) on da850/omap-l138 EVM/Hawkboard, +* hence they are being reserved for codecs on the DSP side. +*/ +static const s16 da850_dma0_rsv_chans[][2 ] = { +/* (offset, number) */ + {8 ,6 }, + {24 ,4 }, + {30 ,2 }, + {-1 ,-1 } +}; + +static const s16 da850_dma0_rsv_slots[][2 ] = { +/* (offset, number) */ + {8 ,6 }, + {24 ,4 }, + {30 ,50 }, + {-1 ,-1 } +}; + +static const s16 da850_dma1_rsv_chans[][2 ] = { +/* (offset, number) */ + {0 ,28 }, + {30 ,2 }, + {-1 ,-1 } +}; + +static const s16 da850_dma1_rsv_slots[][2 ] = { +/* (offset, number) */ + {0 ,28 }, + {30 ,90 }, + {-1 ,-1 } +}; + +static struct edma_rsv_info da850_edma_cc0_rsv = { + .rsv_chans = da850_dma0_rsv_chans, + .rsv_slots = da850_dma0_rsv_slots, +}; + +static struct edma_rsv_info da850_edma_cc1_rsv = { + .rsv_chans = da850_dma1_rsv_chans, + .rsv_slots = da850_dma1_rsv_slots, +}; + +static struct edma_rsv_info *da850_edma_rsv[2 ] = { + &da850_edma_cc0_rsv, + &da850_edma_cc1_rsv, +};static struct davinci_uart_config omapl138_hawk_uart_config__initdata = { .enabled_uarts =0x7 ,
@@ -73,6 +122,11 @@ static __init void omapl138_hawk_init(void)omapl138_hawk_config_emac (); + ret =da850_register_edma (da850_edma_rsv); +if (ret) +pr_warning ("%s: EDMA registration failed: %d\n" , + __func__, ret); + ret =da8xx_register_watchdog ();if (ret) pr_warning("omapl138_hawk_init: "
Signature · 1 line
1.7.0.4
PATCH v8 3/9 davinci: ASoC support for Omapl138-Hawkboard
In reply to a message not in the archiveFrom: Victor Rodriguez <[email protected]>
This patch adds ASoC support for the Hawkboard-L138 system
--- sound/soc/davinci/Kconfig | 5 +++-- sound/soc/davinci/davinci-evm.c | 6 ++++-- 2 files changed, 7 insertions(+), 4 deletions(-)
sound/soc/davinci/Kconfig +3 -2
@@ -76,8 +76,9 @@ config SND_DA830_SOC_EVM DA830/OMAP-L137 EVM config SND_DA850_SOC_EVM - tristate "SoC Audio support for DA850/OMAP-L138 EVM" - depends on SND_DAVINCI_SOC && MACH_DAVINCI_DA850_EVM + tristate "SoC Audio support for DA850/OMAP-L138 EVM/Hawkboard" + depends on SND_DAVINCI_SOC && (MACH_DAVINCI_DA850_EVM || \ + MACH_OMAPL138_HAWKBOARD) select SND_DAVINCI_SOC_MCASP select SND_SOC_TLV320AIC3X help
sound/soc/davinci/davinci-evm.c +4 -2
@@ -59,7 +59,8 @@ static int evm_hw_params(struct snd_pcm_substream *substream, sysclk =12288000 ; else if (machine_is_davinci_da830_evm() || -machine_is_davinci_da850_evm ()) + machine_is_davinci_da850_evm() || +machine_is_omapl138_hawkboard ()) sysclk =24576000 ; else
@@ -311,7 +312,8 @@ static int __init evm_init(void) }else if (machine_is_davinci_da830_evm ()) { evm_snd_dev_data = &da830_evm_snd_devdata; index =1 ; - }else if (machine_is_davinci_da850_evm ()) { + }else if (machine_is_davinci_da850_evm () || +machine_is_omapl138_hawkboard ()) { evm_snd_dev_data = &da850_evm_snd_devdata; index =0 ; }else
Signature · 1 line
1.7.0.4
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
In reply to a message not in the archiveFrom: Victor Rodriguez <[email protected]>
This patch defines Pin Mux configuration for MacASP used on the Hawkboard-L138 system in order to add Audio support
--- arch/arm/mach-davinci/da850.c | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-)
arch/arm/mach-davinci/da850.c +1 -1
@@ -591,7 +591,7 @@ const short da850_cpgmac_pins[] __initdata = {const short da850_mcasp_pins[]__initdata = {DA850_AHCLKX ,DA850_ACLKX ,DA850_AFSX ,DA850_AHCLKR ,DA850_ACLKR ,DA850_AFSR ,DA850_AMUTE , -DA850_AXR_11 ,DA850_AXR_12 , +DA850_AXR_11 ,DA850_AXR_12 ,DA850_AXR_13 ,DA850_AXR_14 ,-1 };
Signature · 1 line
1.7.0.4
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
Hi Victor,
Quoted 16 lines · On Sat, Nov 13, 2010 at 04:08:50, vm.rod25 at gmail.com wrote:
From: Victor Rodriguez <[email protected]>
This patch defines Pin Mux configuration for MacASP used on the Hawkboard-L138 system in order to add Audio support
Signed-off-by Victor Rodriguez <[email protected]>Tested-by Rene Gonzalez <[email protected]>--- arch/arm/mach-davinci/da850.c | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-)arch/arm/mach-davinci/da850.c +0
-0
arch/arm/mach-davinci/da850.c const short da850_cpgmac_pins[] __initdata = { · line 594
Quoted 5 lines
arch/arm/mach-davinci/da850.c +1
-1@@ -591,7 +591,7 @@ const short da850_cpgmac_pins[] __initdata = {const short da850_mcasp_pins[]__initdata = {DA850_AHCLKX ,DA850_ACLKX ,DA850_AFSX ,DA850_AHCLKR ,DA850_ACLKR ,DA850_AFSR ,DA850_AMUTE , -DA850_AXR_11 ,DA850_AXR_12 , +DA850_AXR_11 ,DA850_AXR_12 ,DA850_AXR_13 ,DA850_AXR_14 ,
Looks like I missed pointing this out previously, but extending this list to take care of all boards will not be right since (for example) AXR13 and AXR14 pins could be used for different purpose on different boards.
The right way would be to make this a per-board list. Since it is marked __initdata, that wouldn't lead to bloat.
Thanks,
Sekhar
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
Quoted 6 lines · Sekhar
Quoted 5 lines
This patch defines Pin Mux configuration for MacASP used on the Hawkboard-L138 system in order to add Audio support
Signed-off-by Victor Rodriguez<[email protected]>Tested-by Rene Gonzalez<[email protected]>
Quoted 15 lines
arch/arm/mach-davinci/da850.c const short da850_cpgmac_pins[] __initdata = { · line 594
Quoted 10 lines
arch/arm/mach-davinci/da850.c +1
-1@@ -591,7 +591,7 @@ const short da850_cpgmac_pins[] __initdata = {const short da850_mcasp_pins[]__initdata = {DA850_AHCLKX ,DA850_ACLKX ,DA850_AFSX ,DA850_AHCLKR ,DA850_ACLKR ,DA850_AFSR ,DA850_AMUTE , -DA850_AXR_11 ,DA850_AXR_12 , +DA850_AXR_11 ,DA850_AXR_12 ,DA850_AXR_13 ,DA850_AXR_14 ,Looks like I missed pointing this out previously, but extending this list to take care of all boards will not be right since (for example) AXR13 and AXR14 pins could be used for different purpose on different boards.
This is correct as the list in da850.c is a *generic* module's pin list.
If the board needs less pins (and the pins it does not use for McASP are used differently), it should define its own pin list.
Quoted 2 lines
The right way would be to make this a per-board list. Since it is marked
__initdata, that wouldn't lead to bloat.
This patch is correct anyway. Unless DA850 EVM board can't use these pins
for McASP -- but in this case the corresponding board file needs the specific pin list added.
Quoted 2 lines
Thanks,
Sekhar
WBR, Sergei
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
Hi Sergei,
Quoted 28 lines · Sergei Shtylyov
Quoted 6 lines · Sekhar
Quoted 5 lines
This patch defines Pin Mux configuration for MacASP used on the Hawkboard-L138 system in order to add Audio support
Signed-off-by Victor Rodriguez<[email protected]>Tested-by Rene Gonzalez<[email protected]>Quoted 15 lines
arch/arm/mach-davinci/da850.c const short da850_cpgmac_pins[] __initdata = { · line 594
Quoted 10 lines
arch/arm/mach-davinci/da850.c +1
-1@@ -591,7 +591,7 @@ const short da850_cpgmac_pins[] __initdata = {const short da850_mcasp_pins[]__initdata = {DA850_AHCLKX ,DA850_ACLKX ,DA850_AFSX ,DA850_AHCLKR ,DA850_ACLKR ,DA850_AFSR ,DA850_AMUTE , -DA850_AXR_11 ,DA850_AXR_12 , +DA850_AXR_11 ,DA850_AXR_12 ,DA850_AXR_13 ,DA850_AXR_14 ,Looks like I missed pointing this out previously, but extending this list to take care of all boards will not be right since (for example) AXR13 and AXR14 pins could be used for different purpose on different boards.
This is correct as the list in
da850.cis a *generic* module's pin list.
If the board needs less pins (and the pins it does not use for McASP are used differently), it should define its own pin list.
Quoted 6 lines
Quoted 2 lines
The right way would be to make this a per-board list. Since it is marked
__initdata, that wouldn't lead to bloat.This patch is correct anyway. Unless DA850 EVM board can't use these pins
for McASP -- but in this case the corresponding board file needs the specific pin list added.
Okay. I guess you are saying we will keep adding pins to the generic list as long as *all* supported boards don't get a conflict and if we run into a conflict we will spawn separate list for the affected board.
The only issue I see with this approach is it puts too much burden on the developer to verify that none of the supported boards break.
Since it is highly unlikely that any board will need all the McASP pins, the generic list will likely remain unused. It might just be easier to start using board specific lists right away. This is especially true for McASP where usage of pins across boards will likely vary widely.
Thanks,
Sekhar
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
Quoted 45 lines · Sekhar
Hi Sergei,
Quoted 28 lines · Sergei Shtylyov
Quoted 6 lines · Sekhar
Quoted 5 lines
This patch defines Pin Mux configuration for MacASP used on the Hawkboard-L138 system in order to add Audio support
Signed-off-by Victor Rodriguez<[email protected]>Tested-by Rene Gonzalez<[email protected]>Quoted 15 lines
arch/arm/mach-davinci/da850.c const short da850_cpgmac_pins[] __initdata = { · line 594
Quoted 10 lines
arch/arm/mach-davinci/da850.c +1
-1@@ -591,7 +591,7 @@ const short da850_cpgmac_pins[] __initdata = { ? const short da850_mcasp_pins[] __initdata = { ? ? ? ?DA850_AHCLKX, DA850_ACLKX, DA850_AFSX, ? ? ? ?DA850_AHCLKR, DA850_ACLKR, DA850_AFSR, DA850_AMUTE, - ? ? DA850_AXR_11, DA850_AXR_12, + ? ? DA850_AXR_11, DA850_AXR_12, DA850_AXR_13, DA850_AXR_14,Looks like I missed pointing this out previously, but extending this list to take care of all boards will not be right since (for example) AXR13 and AXR14 pins could be used for different purpose on different boards.
? ? This is correct as the list in
da850.cis a *generic* module's pin list. If the board needs less pins (and the pins it does not use for McASP are used differently), it should define its own pin list.Quoted 6 lines
Quoted 2 lines
The right way would be to make this a per-board list. Since it is marked
__initdata, that wouldn't lead to bloat.? ? This patch is correct anyway. Unless DA850 EVM board can't use these pins for McASP -- but in this case the corresponding board file needs the specific pin list added.
Okay. I guess you are saying we will keep adding pins to the generic list as long as *all* supported boards don't get a conflict and if we run into a conflict we will spawn separate list for the affected board.
The only issue I see with this approach is it puts too much burden on the developer to verify that none of the supported boards break.
Quoted 9 lines
Since it is highly unlikely that any board will need all the McASP pins, the generic list will likely remain unused. It might just be easier to start using board specific lists right away. This is especially true for McASP where usage of pins across boards will likely vary widely.
Thanks,
Sekhar
Hi All
Please confirme me if the path is rigth or if I should make a McASP list for the board.
Regards
Victor Rodriguez
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
In reply to Nori, SekharHello.
Quoted 27 lines · Sekhar
Quoted 26 lines
Quoted 11 lines
Quoted 11 lines
This patch defines Pin Mux configuration for MacASP used on the Hawkboard-L138 system in order to add Audio support
Signed-off-by Victor Rodriguez<[email protected]>Tested-by Rene Gonzalez<[email protected]>arch/arm/mach-davinci/da850.c +0
-0@@ -591,7 +591,7 @@ const short da850_cpgmac_pins[] __initdata = {const short da850_mcasp_pins[]__initdata = {DA850_AHCLKX ,DA850_ACLKX ,DA850_AFSX ,Quoted 8 lines
arch/arm/mach-davinci/da850.c const short da850_cpgmac_pins[] __initdata = { · line 594
Quoted 3 lines
arch/arm/mach-davinci/da850.c +1
-1DA850_AHCLKR ,DA850_ACLKR ,DA850_AFSR ,DA850_AMUTE , - DA850_AXR_11, DA850_AXR_12, + DA850_AXR_11, DA850_AXR_12, DA850_AXR_13, DA850_AXR_14,Looks like I missed pointing this out previously, but extending this list to take care of all boards will not be right since (for example) AXR13 and AXR14 pins could be used for different purpose on different boards.
This is correct as the list in
da850.cis a *generic* module's pin list.
If the board needs less pins (and the pins it does not use for McASP are used differently), it should define its own pin list.Quoted 2 lines
The right way would be to make this a per-board list. Since it is marked
__initdata, that wouldn't lead to bloat.
Quoted 6 lines
Quoted 3 lines
This patch is correct anyway. Unless DA850 EVM board can't use these pins
for McASP -- but in this case the corresponding board file needs the specific pin list added.Okay. I guess you are saying we will keep adding pins to the generic list as long as *all* supported boards don't get a conflict
No, I don't care about conflicts as long as da850.c is concerned.
Quoted 2 lines
and if we run into
a conflict we will spawn separate list for the affected board.
Yes.
Quoted 2 lines
The only issue I see with this approach is it puts too much burden on the developer to verify that none of the supported boards break.
That should be verified by the owners of that board. They shouldn't even
have used the generic pin lists in the first place. The conception behind pin lists in da850.c was celarly misunderstood when DA850 EVM code was developed.
Quoted 2 lines
Since it is highly unlikely that any board will need all the McASP pins, the generic list will likely remain unused.
At least for now, Hawkboard will use all the defined pins -- I don't know if
there are any more undefined yet...
Quoted 3 lines
It might just be easier to
start using board specific lists right away. This is especially true for McASP where usage of pins across boards will likely vary widely.
Well, that depends on how complete the new generic McASP pin list is. If
it's still not, then board specific pin list looks preferable indeed...
Quoted 2 lines
Thanks,
Sekhar
WBR, Sergei
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
Quoted 68 lines · Sergei Shtylyov
Hello.
Quoted 30 lines · Sekhar
Quoted 29 lines
Quoted 12 lines
Quoted 12 lines
This patch defines Pin Mux configuration for MacASP used on the Hawkboard-L138 system in order to add Audio support
Signed-off-by Victor Rodriguez<[email protected]>Tested-by Rene Gonzalez<[email protected]>arch/arm/mach-davinci/da850.c +0
-0@@ -591,7 +591,7 @@ const short da850_cpgmac_pins[] __initdata = { ?const short da850_mcasp_pins[] __initdata = { ? ? ? DA850_AHCLKX, DA850_ACLKX, DA850_AFSX,Quoted 8 lines
arch/arm/mach-davinci/da850.c const short da850_cpgmac_pins[] __initdata = { · line 594
Quoted 3 lines
arch/arm/mach-davinci/da850.c +1
-1? ? ? DA850_AHCLKR, DA850_ACLKR, DA850_AFSR, DA850_AMUTE, - ? ? DA850_AXR_11, DA850_AXR_12, + ? ? DA850_AXR_11, DA850_AXR_12, DA850_AXR_13, DA850_AXR_14,Looks like I missed pointing this out previously, but extending this list to take care of all boards will not be right since (for example) AXR13 and AXR14 pins could be used for different purpose on different boards.
? ?This is correct as the list in
da850.cis a *generic* module's pin list.
If the board needs less pins (and the pins it does not use for McASP are used
differently), it should define its own pin list.Quoted 2 lines
The right way would be to make this a per-board list. Since it is marked
__initdata, that wouldn't lead to bloat.Quoted 8 lines
Quoted 5 lines
? ?This patch is correct anyway. Unless DA850 EVM board can't use these pins
for McASP -- but in this case the corresponding board file needs the specific
pin list added.Okay. I guess you are saying we will keep adding pins to the generic list as long as *all* supported boards don't get a conflict
? No, I don't care about conflicts as long as
da850.cis concerned.Quoted 2 lines
and if we run into
a conflict we will spawn separate list for the affected board.? Yes.
Quoted 2 lines
The only issue I see with this approach is it puts too much burden on the developer to verify that none of the supported boards break.
? That should be verified by the owners of that board. They shouldn't even have used the generic pin lists in the first place. The conception behind pin lists in
da850.cwas celarly misunderstood when DA850 EVM code was developed.Quoted 2 lines
Since it is highly unlikely that any board will need all the McASP pins, the generic list will likely remain unused.
? At least for now, Hawkboard will use all the defined pins -- I don't know if there are any more undefined yet...
Quoted 3 lines
It might just be easier to
start using board specific lists right away. This is especially true for McASP where usage of pins across boards will likely vary widely.
Quoted 8 lines
? Well, that depends on how complete the new generic McASP pin list is. If it's still not, then board specific pin list looks preferable indeed...
Quoted 2 lines
Thanks,
SekharWBR, Sergei
HI Sergei and Sekhar
Thanks for check the patch
What I can do if you agree with this change is to leave da850.c as it is, and declare
static short hawk_mcasp_pins[] __initdata = {
DA850_AHCLKX, DA850_ACLKX, DA850_AFSX,
DA850_AHCLKR, DA850_ACLKR, DA850_AFSR, DA850_AMUTE,
DA850_AXR_11, DA850_AXR_12, DA850_AXR_13, DA850_AXR_14,
-1
};on the hawkboard file and call it insted of da850_mcasp_pins.
ret = davinci_cfg_reg_list(hawk_mcasp_pins);
if (ret)
pr_warning("%s: mcasp mux setup failed: %d\n", __func__, ret);Please tell me if you agree with this change, I think is better because I do not touch any other file besides my board file.
Thanks
Regards
Victor Rodriguez
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
Hello.
Quoted 72 lines · Victor Rodriguez
Quoted 71 lines
Quoted 32 lines
Quoted 31 lines
Quoted 6 lines
Quoted 5 lines
This patch defines Pin Mux configuration for MacASP used on the Hawkboard-L138 system in order to add Audio support
Signed-off-by Victor Rodriguez<[email protected]>Tested-by Rene Gonzalez<[email protected]>Quoted 16 lines
arch/arm/mach-davinci/da850.c const short da850_cpgmac_pins[] __initdata = { · line 594
Quoted 11 lines
arch/arm/mach-davinci/da850.c +1
-1@@ -591,7 +591,7 @@ const short da850_cpgmac_pins[] __initdata = {const short da850_mcasp_pins[]__initdata = {DA850_AHCLKX ,DA850_ACLKX ,DA850_AFSX ,DA850_AHCLKR ,DA850_ACLKR ,DA850_AFSR ,DA850_AMUTE , -DA850_AXR_11 ,DA850_AXR_12 , +DA850_AXR_11 ,DA850_AXR_12 ,DA850_AXR_13 ,DA850_AXR_14 ,Looks like I missed pointing this out previously, but extending this list to take care of all boards will not be right since (for example) AXR13 and AXR14 pins could be used for different purpose on different boards.
This is correct as the list in
da850.cis a *generic* module's pin
list.
If the board needs less pins (and the pins it does not use for McASP are used
differently), it should define its own pin list.Quoted 2 lines
The right way would be to make this a per-board list. Since it is marked
__initdata, that wouldn't lead to bloat.Quoted 8 lines
Quoted 5 lines
This patch is correct anyway. Unless DA850 EVM board can't use these
pins
for McASP -- but in this case the corresponding board file needs the specific
pin list added.Okay. I guess you are saying we will keep adding pins to the generic list as long as *all* supported boards don't get a conflict
No, I don't care about conflicts as long as
da850.cis concerned.Quoted 2 lines
and if we run into
a conflict we will spawn separate list for the affected board.Yes.
Quoted 2 lines
The only issue I see with this approach is it puts too much burden on the developer to verify that none of the supported boards break.
That should be verified by the owners of that board. They shouldn't even
have used the generic pin lists in the first place. The conception behind pin lists inda850.cwas celarly misunderstood when DA850 EVM code was developed.Quoted 2 lines
Since it is highly unlikely that any board will need all the McASP pins, the generic list will likely remain unused.
At least for now, Hawkboard will use all the defined pins -- I don't know
if there are any more undefined yet...Quoted 3 lines
It might just be easier to
start using board specific lists right away. This is especially true for McASP where usage of pins across boards will likely vary widely.Well, that depends on how complete the new generic McASP pin list is. If
it's still not, then board specific pin list looks preferable indeed...Quoted 2 lines
Thanks,
Sekhar
Quoted 8 lines
Quoted 1 line
WBR, Sergei
HI Sergei and Sekhar
Thanks for check the patch
What I can do if you agree with this change is to leave
da850.cas it is,
No, please don't.
Quoted 9 lines
and declare
static short hawk_mcasp_pins[] __initdata = { DA850_AHCLKX, DA850_ACLKX, DA850_AFSX, DA850_AHCLKR, DA850_ACLKR, DA850_AFSR, DA850_AMUTE, DA850_AXR_11, DA850_AXR_12, DA850_AXR_13, DA850_AXR_14, -1 };
Quoted 8 lines
on the hawkboard file and call it insted of
da850_mcasp_pins.ret = davinci_cfg_reg_list(hawk_mcasp_pins); if (ret) pr_warning("%s: mcasp mux setup failed: %d\n", __func__, ret);Please tell me if you agree with this change, I think is better because I do not touch any other file besides my board file.
No, it's not really better. The generic list in da850.c should be more
complete, regardless... Ideally, you should go thru the DA850 manual and put in that list all McASP pins that aren't already there. Then you can use your own pin list if that *complete* pin list can't be used on your board.
Quoted 5 lines
Thanks
Regards
Victor Rodriguez
WBR, Sergei
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
Quoted 25 lines · Sergei Shtylyov
Quoted 7 lines
HI Sergei and Sekhar
Thanks for check the patch
What I can do if you agree with this change is to leave
da850.cas it is,No, please don't.
Quoted 14 lines
and declare
static short hawk_mcasp_pins[] __initdata = { DA850_AHCLKX, DA850_ACLKX, DA850_AFSX, DA850_AHCLKR, DA850_ACLKR, DA850_AFSR, DA850_AMUTE, DA850_AXR_11, DA850_AXR_12, DA850_AXR_13, DA850_AXR_14, -1 };on the hawkboard file and call it insted of
da850_mcasp_pins.ret = davinci_cfg_reg_list(hawk_mcasp_pins); if (ret) pr_warning("%s: mcasp mux setup failed: %d\n", __func__, ret);
Quoted 7 lines
Quoted 2 lines
Please tell me if you agree with this change, I think is better because I do not touch any other file besides my board file.
No, it's not really better. The generic list in
da850.cshould be more
complete, regardless... Ideally, you should go thru the DA850 manual and put in that list all McASP pins that aren't already there. Then you can use your own pin list if that *complete* pin list can't be used on your board.
That will cause a bunch of pin conflicts on the EVM so it will need its own list too.
Thanks,
Sekhar
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
Quoted 35 lines · Sekhar
Quoted 25 lines · Sergei Shtylyov
Quoted 7 lines
HI Sergei and Sekhar
Thanks for check the patch
What I can do if you agree with this change is to leave
da850.cas it is,? ? No, please don't.
Quoted 14 lines
and declare
static short hawk_mcasp_pins[]
__initdata= {
? ?DA850_AHCLKX,DA850_ACLKX,DA850_AFSX,
? ?DA850_AHCLKR,DA850_ACLKR,DA850_AFSR,DA850_AMUTE, ? ?DA850_AXR_11,DA850_AXR_12,DA850_AXR_13,DA850_AXR_14, ? ? -1
};on the hawkboard file and call it insted of
da850_mcasp_pins.? ? ret =
davinci_cfg_reg_list(hawk_mcasp_pins);
? ? if (ret)
? ? ? ? ? ?pr_warning("%s: mcasp mux setup failed: %d\n", __func__, ret);Quoted 7 lines
Quoted 2 lines
Please tell me if you agree with this change, I think is better because I do not touch any other file besides my board file.
? ? No, it's not really better. The generic list in
da850.cshould be more complete, regardless... Ideally, you should go thru the DA850 manual and put in that list all McASP pins that aren't already there. Then you can use your own pin list if that *complete* pin list can't be used on your board.
Quoted 7 lines
That will cause a bunch of pin conflicts on the EVM so it will need its own list too.
Thanks,
Sekhar
So do you think that the peer-board list (as I am implementing ) would be a better idea ?
Regards
Victor Rodriguez
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
In reply to Nori, SekharQuoted 30 lines · Sekhar
Quoted 28 lines · Sergei Shtylyov
Quoted 7 lines
HI Sergei and Sekhar
Thanks for check the patch
What I can do if you agree with this change is to leave
da850.cas it is,No, please don't.
Quoted 17 lines
and declare
static short hawk_mcasp_pins[] __initdata = { DA850_AHCLKX, DA850_ACLKX, DA850_AFSX, DA850_AHCLKR, DA850_ACLKR, DA850_AFSR, DA850_AMUTE, DA850_AXR_11, DA850_AXR_12, DA850_AXR_13, DA850_AXR_14, -1 };on the hawkboard file and call it insted of
da850_mcasp_pins.ret = davinci_cfg_reg_list(hawk_mcasp_pins); if (ret) pr_warning("%s: mcasp mux setup failed: %d\n", __func__, ret);Please tell me if you agree with this change, I think is better because I do not touch any other file besides my board file.
Quoted 8 lines
Quoted 4 lines
No, it's not really better. The generic list in
da850.cshould be more
complete, regardless... Ideally, you should go thru the DA850 manual and put in that list all McASP pins that aren't already there. Then you can use your own pin list if that *complete* pin list can't be used on your board.That will cause a bunch of pin conflicts on the EVM so it will need its own list too.
Help me out. Why do we need generic pin lists?
It seems to me that the "generic pin list" for da850.c isn't practical for most (if not all) of the peripherals. They should be done using __initdata in each board file.
Just a cursory glance at what's in da850.c highlights several items being set up for the EVM and not generically. For example:
- da850_uart1_pins and da850_uart2_pins: I believe both have RTS/CTS pins which for a generic definition should be included as for UART0, but would then be unused as the EVM doesn't use these pins in this function.
- da850_mcasp_pins: if generic, must include all 16 AXR pins. I think you'd be hard pressed to find a board configuration that would use all 16 AXR pins for the McASP. I'm fairly sure the EVM uses the pins called out, and uses other pins for other functions. So it's likely this structure wouldn't get used.
- da850_mmcsd0_pins : includes 2 GPIO pins (specific to the EVM, though possible for other boards) for the card detect and write protect signals. These pins are completely arbitrary for that particular board design. I also believe that the complete mmcsd0 port has 4 more data lines as part of it's peripheral, although the driver doesn't support using them.
- da850_emif25_pins interface doesn't include the generic pins for some of the SDRAM functions.
- da850_cpgmac_pins defines both RMII and MII pins. I don't think any board would want to configure both sets at the same time. Seems like this should never get used...
It's also incomplete. What about the uPP pin list? Or the VPIF? Etc.
I think a board file author should be familiar enough with the SoC to understand what peripheral pins he should be configuring for his/her particular hardware setup and explicitly specify them in the board file.
If you remove the common pin-mux lists and move them to a board file, then once you configure your specific platform, is there any more memory used than with
the common scheme? Of course, there would be replication of pin-mux code in the board files that had identical configurations. Is that the driver for the current implementation?
Is there a thread that hashes through the decisions on this that I should be googling?
Thanks for any insight.
-Mike
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
________________________________________
From: Michael Williamson [michael.williamson at criticallink.com]
Sent: Tuesday, November 16, 2010 2:42 PM
To: Nori, Sekhar
Cc: Sergei Shtylyov; Victor Rodriguez; davinci-linux-open-source at linux.davincidsp.com; Russell King; Victor Rodriguez; linux-arm-kernel at lists.infradead.org
Subject: Re: [PATCH v8 4/9] davinci: McASP configuration for Omapl138-Hawkboard
Quoted 30 lines · Sekhar
Quoted 28 lines · Sergei Shtylyov
Quoted 7 lines
HI Sergei and Sekhar
Thanks for check the patch
What I can do if you agree with this change is to leave
da850.cas it is,No, please don't.
Quoted 17 lines
and declare
static short hawk_mcasp_pins[] __initdata = { DA850_AHCLKX, DA850_ACLKX, DA850_AFSX, DA850_AHCLKR, DA850_ACLKR, DA850_AFSR, DA850_AMUTE, DA850_AXR_11, DA850_AXR_12, DA850_AXR_13, DA850_AXR_14, -1 };on the hawkboard file and call it insted of
da850_mcasp_pins.ret = davinci_cfg_reg_list(hawk_mcasp_pins); if (ret) pr_warning("%s: mcasp mux setup failed: %d\n", __func__, ret);Please tell me if you agree with this change, I think is better because I do not touch any other file besides my board file.
Quoted 8 lines
Quoted 4 lines
No, it's not really better. The generic list in
da850.cshould be more
complete, regardless... Ideally, you should go thru the DA850 manual and put in that list all McASP pins that aren't already there. Then you can use your own pin list if that *complete* pin list can't be used on your board.That will cause a bunch of pin conflicts on the EVM so it will need its own list too.
Help me out. Why do we need generic pin lists?
It seems to me that the "generic pin list" for da850.c isn't practical for most (if not all) of the peripherals. They should be done using __initdata in each board file.
Just a cursory glance at what's in da850.c highlights several items being set up for the EVM and not generically. For example:
- da850_uart1_pins and da850_uart2_pins: I believe both have RTS/CTS pins which for a generic definition should be included as for UART0, but would then be unused as the EVM doesn't use these pins in this function.
- da850_mcasp_pins: if generic, must include all 16 AXR pins. I think you'd be hard pressed to find a board configuration that would use all 16 AXR pins for the McASP. I'm fairly sure the EVM uses the pins called out, and uses other pins for other functions. So it's likely this structure wouldn't get used.
- da850_mmcsd0_pins : includes 2 GPIO pins (specific to the EVM, though possible for other boards) for the card detect and write protect signals. These pins are completely arbitrary for that particular board design. I also believe that the complete mmcsd0 port has 4 more data lines as part of it's peripheral, although the driver doesn't support using them.
- da850_emif25_pins interface doesn't include the generic pins for some of the SDRAM functions.
- da850_cpgmac_pins defines both RMII and MII pins. I don't think any board would want to configure both sets at the same time. Seems like this should never get used...
It's also incomplete. What about the uPP pin list? Or the VPIF? Etc.
I think a board file author should be familiar enough with the SoC to understand what peripheral pins he should be configuring for his/her particular hardware setup and explicitly specify them in the board file.
If you remove the common pin-mux lists and move them to a board file, then once you configure your specific platform, is there any more memory used than with
the common scheme? Of course, there would be replication of pin-mux code in the board files that had identical configurations. Is that the driver for the current implementation?
Is there a thread that hashes through the decisions on this that I should be googling?
Thanks for any insight.
-Mike
Hi Mike thanks for the comments I agree with the part of replication
So do you recommend that the best way to solve this problem is to make a pin list that has all the 16 pins on da850.c ?
I have checked and on the file
arch/arm/mach-davinci/include/mach/mux.h
are declared
/* McASP function */
DA850_ACLKR,
DA850_ACLKX,
DA850_AFSR,
DA850_AFSX,
DA850_AHCLKR,
DA850_AHCLKX,
DA850_AMUTE,
DA850_AXR_15,
DA850_AXR_14,
DA850_AXR_13,
DA850_AXR_12,
DA850_AXR_11,
DA850_AXR_10,
DA850_AXR_9,
DA850_AXR_8,
DA850_AXR_7,
DA850_AXR_6,
DA850_AXR_5,
DA850_AXR_4,
DA850_AXR_3,
DA850_AXR_2,
DA850_AXR_1,
DA850_AXR_0,I have changed the pin list to
const short da850_mcasp_pins[] __initdata = {
DA850_AHCLKX, DA850_ACLKX, DA850_AFSX,
DA850_AHCLKR, DA850_ACLKR, DA850_AFSR, DA850_AMUTE,
DA850_AXR_11, DA850_AXR_12,DA850_AXR_13, DA850_AXR_14, DA850_AXR_15,
-1
};and after checked with the hawk board it works fine
I have put on the list all the available pins for McASP even if hawkboard does not need the last one DA850_AXR_15 , and is still working
Please tell me which way do you recommend me
Regards
Victor Rodriguez
SASKEN BUSINESS DISCLAIMER: This message may contain confidential, proprietary or legally privileged information. In case you are not the original intended Recipient of the message, you must not, directly or indirectly, use, disclose, distribute, print, or copy any part of this message and you are requested to delete it and inform the sender. Any views expressed in this message are those of the individual sender unless otherwise stated. Nothing contained in this message shall be construed as an offer or acceptance of any offer by Sasken Communication Technologies Limited ("Sasken") unless sent with that express intent and with due authority of Sasken. Sasken has taken enough precautions to prevent the spread of viruses. However the company accepts no liability for any damage caused by any virus transmitted by this email. Read Disclaimer at http://www.sasken.com/extras/mail_disclaimer.html
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
In reply to Michael WilliamsonQuoted 84 lines · Michael Williamson
Quoted 30 lines · Sekhar
Quoted 28 lines · Sergei Shtylyov
Quoted 7 lines
HI Sergei and Sekhar
Thanks for check the patch
What I can do if you agree with this change is to leave
da850.cas it is,? ? No, please don't.
Quoted 17 lines
and declare
static short hawk_mcasp_pins[]
__initdata= {
? ?DA850_AHCLKX,DA850_ACLKX,DA850_AFSX,
? ?DA850_AHCLKR,DA850_ACLKR,DA850_AFSR,DA850_AMUTE, ? ?DA850_AXR_11,DA850_AXR_12,DA850_AXR_13,DA850_AXR_14, ? ? -1
};on the hawkboard file and call it insted of
da850_mcasp_pins.? ? ret =
davinci_cfg_reg_list(hawk_mcasp_pins);
? ? if (ret)
? ? ? ? ? ?pr_warning("%s: mcasp mux setup failed: %d\n", __func__, ret);Please tell me if you agree with this change, I think is better because I do not touch any other file besides my board file.
Quoted 8 lines
Quoted 4 lines
? ? No, it's not really better. The generic list in
da850.cshould be more complete, regardless... Ideally, you should go thru the DA850 manual and put in that list all McASP pins that aren't already there. Then you can use your own pin list if that *complete* pin list can't be used on your board.That will cause a bunch of pin conflicts on the EVM so it will need its own list too.
Help me out. ?Why do we need generic pin lists?
It seems to me that the "generic pin list" for
da850.cisn't practical for most (if not all) of the peripherals. ?They should be done using__initdatain each board file.Just a cursory glance at what's in
da850.chighlights several items being set up for the EVM and not generically. ?For example:-
da850_uart1_pinsandda850_uart2_pins: I believe both have RTS/CTS pins which ?for a generic definition should be included as for UART0, but would then ?be unused as the EVM doesn't use these pins in this function.-
da850_mcasp_pins: if generic, must include all 16 AXR pins. ?I think you'd ?be hard pressed to find a board configuration that would use all 16 AXR pins ?for the McASP. ?I'm fairly sure the EVM uses the pins called out, and uses ?other pins for other functions. ?So it's likely this structure wouldn't get used.-
da850_mmcsd0_pins: includes 2 GPIO pins (specific to the EVM, though possible for ?other boards) for the card detect and write protect signals. ?These pins are ?completely arbitrary for that particular board design. I also believe that ?the complete mmcsd0 port has 4 more data lines as part of it's peripheral, although ?the driver doesn't support using them.-
da850_emif25_pinsinterface doesn't include the generic pins for some of ?the SDRAM functions.-
da850_cpgmac_pinsdefines both RMII and MII pins. ?I don't think any board ?would want to configure both sets at the same time. ?Seems like this should ?never get used...It's also incomplete. ?What about the uPP pin list? ?Or the VPIF? ?Etc.
I think a board file author should be familiar enough with the SoC to understand what peripheral pins he should be configuring for his/her particular hardware setup and explicitly specify them in the board file.
If you remove the common pin-mux lists and move them to a board file, then once you configure your specific platform, is there any more memory used than with
the common scheme? ?Of course, there would be replication of pin-mux code in the board files that had identical configurations. ?Is that the driver for the current implementation?
Quoted 12 lines
Is there a thread that hashes through the decisions on this that I should be googling?
Thanks for any insight.
-Mike
Hi Mike thanks for the comments I agree with the part of replication
So do you recommend that the best way to solve this problem is to make a pin list that has all the 16 pins on da850.c ?
I have checked and on the file
arch/arm/mach-davinci/include/mach/mux.h
are declared
/* McASP function */
DA850_ACLKR,
DA850_ACLKX,
DA850_AFSR,
DA850_AFSX,
DA850_AHCLKR,
DA850_AHCLKX,
DA850_AMUTE,
DA850_AXR_15,
DA850_AXR_14,
DA850_AXR_13,
DA850_AXR_12,
DA850_AXR_11,
DA850_AXR_10,
DA850_AXR_9,
DA850_AXR_8,
DA850_AXR_7,
DA850_AXR_6,
DA850_AXR_5,
DA850_AXR_4,
DA850_AXR_3,
DA850_AXR_2,
DA850_AXR_1,
DA850_AXR_0,I have changed the pin list to
const short da850_mcasp_pins[] __initdata = {
DA850_AHCLKX, DA850_ACLKX, DA850_AFSX,
DA850_AHCLKR, DA850_ACLKR, DA850_AFSR, DA850_AMUTE,
DA850_AXR_11, DA850_AXR_12,DA850_AXR_13, DA850_AXR_14, DA850_AXR_15,
-1
};and after checked with the hawk board it works fine
I have put on the list all the available pins for McASP even if hawkboard does not need the last one DA850_AXR_15 , and is still working
Please tell me which way do you recommend me
Regards
Victor Rodriguez
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
In reply to Michael WilliamsonHi Michael,
Quoted 3 lines · Michael Williamson
Help me out. Why do we need generic pin lists?
They might help in cases where all boards will use the same set of pins. For example, every one who uses I2C will most likely both the clock and data pins from the IP. For more complex peripherals with different pins options they serve a documentation purpose at best.
Quoted 3 lines
It seems to me that the "generic pin list" for
da850.cisn't practical for most (if not all) of the peripherals. They should be done using__initdatain each board file.
Yes, agreed.
Quoted 7 lines
Just a cursory glance at what's in
da850.chighlights several items being set up for the EVM and not generically. For example:-
da850_uart1_pinsandda850_uart2_pins: I believe both have RTS/CTS pins which for a generic definition should be included as for UART0, but would then be unused as the EVM doesn't use these pins in this function.
Yes, the generic pin list should have RTS and CTS pins defined for UART1 and UART2. This needs fixing.
Quoted 5 lines
-
da850_mcasp_pins: if generic, must include all 16 AXR pins. I think you'd be hard pressed to find a board configuration that would use all 16 AXR pins for the McASP. I'm fairly sure the EVM uses the pins called out, and uses other pins for other functions. So it's likely this structure wouldn't get used.
Yes, the generic pin list should either be completed or removed altogether and the existing pin list da850_mcasp_pins should be copied into the board file and called da850_evm_mcasp_pins.
Quoted 6 lines
-
da850_mmcsd0_pins: includes 2 GPIO pins (specific to the EVM, though possible for other boards) for the card detect and write protect signals. These pins are completely arbitrary for that particular board design. I also believe that the complete mmcsd0 port has 4 more data lines as part of it's peripheral, although the driver doesn't support using them.
This is incorrect again. The generic pin list should be completed (or removed) and the existing list should be copied into the EVM board file as da850_evm_mmcsd0_pins.
Quoted 3 lines
-
da850_emif25_pinsinterface doesn't include the generic pins for some of the SDRAM functions.
Yes, this should be completed (or removed). This list is unused anyway.
Quoted 4 lines
-
da850_cpgmac_pinsdefines both RMII and MII pins. I don't think any board would want to configure both sets at the same time. Seems like this should never get used...
Agreed.
Quoted 2 lines
It's also incomplete. What about the uPP pin list? Or the VPIF? Etc.
These should be added as the drivers for these devices are supported.
Quoted 4 lines
I think a board file author should be familiar enough with the SoC to understand what peripheral pins he should be configuring for his/her particular hardware setup and explicitly specify them in the board file.
Agree.
Quoted 4 lines
If you remove the common pin-mux lists and move them to a board file, then once you configure your specific platform, is there any more memory used than with the common scheme? Of course, there would be replication of pin-mux code in the board
There is no memory wastage. All the pin lists are init data.
I too prefer all generic pin lists which are most likely not going to be used at all to be removed. Unused stuff like this will only make code difficult to read.
Thanks,
Sekhar
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
Quoted 81 lines · Sekhar
Hi Michael,
Quoted 3 lines · Michael Williamson
Help me out. ?Why do we need generic pin lists?
They might help in cases where all boards will use the same set of pins. For example, every one who uses I2C will most likely both the clock and data pins from the IP. For more complex peripherals with different pins options they serve a documentation purpose at best.
Quoted 3 lines
It seems to me that the "generic pin list" for
da850.cisn't practical for most (if not all) of the peripherals. ?They should be done using__initdatain each board file.Yes, agreed.
Quoted 7 lines
Just a cursory glance at what's in
da850.chighlights several items being set up for the EVM and not generically. ?For example:-
da850_uart1_pinsandda850_uart2_pins: I believe both have RTS/CTS pins which ? for a generic definition should be included as for UART0, but would then ? be unused as the EVM doesn't use these pins in this function.Yes, the generic pin list should have RTS and CTS pins defined for UART1 and UART2. This needs fixing.
Quoted 5 lines
-
da850_mcasp_pins: if generic, must include all 16 AXR pins. ?I think you'd ? be hard pressed to find a board configuration that would use all 16 AXR pins ? for the McASP. ?I'm fairly sure the EVM uses the pins called out, and uses ? other pins for other functions. ?So it's likely this structure wouldn't get used.Yes, the generic pin list should either be completed or removed altogether and the existing pin list
da850_mcasp_pinsshould be copied into the board file and calledda850_evm_mcasp_pins.Quoted 6 lines
-
da850_mmcsd0_pins: includes 2 GPIO pins (specific to the EVM, though possible for ? other boards) for the card detect and write protect signals. ?These pins are ? completely arbitrary for that particular board design. I also believe that ? the complete mmcsd0 port has 4 more data lines as part of it's peripheral, although ? the driver doesn't support using them.This is incorrect again. The generic pin list should be completed (or removed) and the existing list should be copied into the EVM board file as
da850_evm_mmcsd0_pins.Quoted 3 lines
-
da850_emif25_pinsinterface doesn't include the generic pins for some of ? the SDRAM functions.Yes, this should be completed (or removed). This list is unused anyway.
Quoted 4 lines
-
da850_cpgmac_pinsdefines both RMII and MII pins. ?I don't think any board ? would want to configure both sets at the same time. ?Seems like this should ? never get used...Agreed.
Quoted 2 lines
It's also incomplete. ?What about the uPP pin list? ?Or the VPIF? ?Etc.
These should be added as the drivers for these devices are supported.
Quoted 4 lines
I think a board file author should be familiar enough with the SoC to understand what peripheral pins he should be configuring for his/her particular hardware setup and explicitly specify them in the board file.
Agree.
Quoted 4 lines
If you remove the common pin-mux lists and move them to a board file, then once you configure your specific platform, is there any more memory used than with the common scheme? ?Of course, there would be replication of pin-mux code in the board
Quoted 10 lines
There is no memory wastage. All the pin lists are init data.
I too prefer all generic pin lists which are most likely not going to be used at all to be removed. Unused stuff like this will only make code difficult to read.
Thanks,
Sekhar
HI Sekhar
Let me see if I understand, you prefer to remove the unused pin list, but that will produce a lot of changes on each board that used these pin list. I do not have those boards, in order to test if that works :(
I want to help to fix it and give a complete and right support to the hawk board.
Please give me a tip of how to do it
Regards
Victor Rodriguez
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
Hi Victor,
On Thu, Nov 18, 2010 at 22:08:34, Victor Rodriguez wrote:
[...]
Quoted 11 lines
HI Sekhar
Let me see if I understand, you prefer to remove the unused pin list, but that will produce a lot of changes on each board that used these pin list. I do not have those boards, in order to test if that works :(
I want to help to fix it and give a complete and right support to the hawk board.
Please give me a tip of how to do it
If you make the changes and post the patches,
we can ack for the EVM. Mike would be able
to test on the Mity-DSP platform.
Anyway, I expect the changes to be fairly innocuous.
Thanks,
Sekhar
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
In reply to Nori, SekharQuoted 81 lines · Sekhar
Hi Michael,
Quoted 3 lines · Michael Williamson
Help me out. Why do we need generic pin lists?
They might help in cases where all boards will use the same set of pins. For example, every one who uses I2C will most likely both the clock and data pins from the IP. For more complex peripherals with different pins options they serve a documentation purpose at best.
Quoted 3 lines
It seems to me that the "generic pin list" for
da850.cisn't practical for most (if not all) of the peripherals. They should be done using__initdatain each board file.Yes, agreed.
Quoted 7 lines
Just a cursory glance at what's in
da850.chighlights several items being set up for the EVM and not generically. For example:-
da850_uart1_pinsandda850_uart2_pins: I believe both have RTS/CTS pins which for a generic definition should be included as for UART0, but would then be unused as the EVM doesn't use these pins in this function.Yes, the generic pin list should have RTS and CTS pins defined for UART1 and UART2. This needs fixing.
Quoted 5 lines
-
da850_mcasp_pins: if generic, must include all 16 AXR pins. I think you'd be hard pressed to find a board configuration that would use all 16 AXR pins for the McASP. I'm fairly sure the EVM uses the pins called out, and uses other pins for other functions. So it's likely this structure wouldn't get used.Yes, the generic pin list should either be completed or removed altogether and the existing pin list
da850_mcasp_pinsshould be copied into the board file and calledda850_evm_mcasp_pins.Quoted 6 lines
-
da850_mmcsd0_pins: includes 2 GPIO pins (specific to the EVM, though possible for other boards) for the card detect and write protect signals. These pins are completely arbitrary for that particular board design. I also believe that the complete mmcsd0 port has 4 more data lines as part of it's peripheral, although the driver doesn't support using them.This is incorrect again. The generic pin list should be completed (or removed) and the existing list should be copied into the EVM board file as
da850_evm_mmcsd0_pins.Quoted 3 lines
-
da850_emif25_pinsinterface doesn't include the generic pins for some of the SDRAM functions.Yes, this should be completed (or removed). This list is unused anyway.
Quoted 4 lines
-
da850_cpgmac_pinsdefines both RMII and MII pins. I don't think any board would want to configure both sets at the same time. Seems like this should never get used...Agreed.
Quoted 2 lines
It's also incomplete. What about the uPP pin list? Or the VPIF? Etc.
These should be added as the drivers for these devices are supported.
Quoted 4 lines
I think a board file author should be familiar enough with the SoC to understand what peripheral pins he should be configuring for his/her particular hardware setup and explicitly specify them in the board file.
Agree.
Quoted 4 lines
If you remove the common pin-mux lists and move them to a board file, then once you configure your specific platform, is there any more memory used than with the common scheme? Of course, there would be replication of pin-mux code in the board
Quoted 5 lines
There is no memory wastage. All the pin lists are init data.
I too prefer all generic pin lists which are most likely not going to be used at all to be removed. Unused stuff like this will only make code difficult to read.
FWIW, I agree.
Now, who wants to tackle it?
Kevin
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
Quoted 89 lines · Kevin Hilman
Quoted 81 lines · Sekhar
Hi Michael,
Quoted 3 lines · Michael Williamson
Help me out. ?Why do we need generic pin lists?
They might help in cases where all boards will use the same set of pins. For example, every one who uses I2C will most likely both the clock and data pins from the IP. For more complex peripherals with different pins options they serve a documentation purpose at best.
Quoted 3 lines
It seems to me that the "generic pin list" for
da850.cisn't practical for most (if not all) of the peripherals. ?They should be done using__initdatain each board file.Yes, agreed.
Quoted 7 lines
Just a cursory glance at what's in
da850.chighlights several items being set up for the EVM and not generically. ?For example:-
da850_uart1_pinsandda850_uart2_pins: I believe both have RTS/CTS pins which ? for a generic definition should be included as for UART0, but would then ? be unused as the EVM doesn't use these pins in this function.Yes, the generic pin list should have RTS and CTS pins defined for UART1 and UART2. This needs fixing.
Quoted 5 lines
-
da850_mcasp_pins: if generic, must include all 16 AXR pins. ?I think you'd ? be hard pressed to find a board configuration that would use all 16 AXR pins ? for the McASP. ?I'm fairly sure the EVM uses the pins called out, and uses ? other pins for other functions. ?So it's likely this structure wouldn't get used.Yes, the generic pin list should either be completed or removed altogether and the existing pin list
da850_mcasp_pinsshould be copied into the board file and calledda850_evm_mcasp_pins.Quoted 6 lines
-
da850_mmcsd0_pins: includes 2 GPIO pins (specific to the EVM, though possible for ? other boards) for the card detect and write protect signals. ?These pins are ? completely arbitrary for that particular board design. I also believe that ? the complete mmcsd0 port has 4 more data lines as part of it's peripheral, although ? the driver doesn't support using them.This is incorrect again. The generic pin list should be completed (or removed) and the existing list should be copied into the EVM board file as
da850_evm_mmcsd0_pins.Quoted 3 lines
-
da850_emif25_pinsinterface doesn't include the generic pins for some of ? the SDRAM functions.Yes, this should be completed (or removed). This list is unused anyway.
Quoted 4 lines
-
da850_cpgmac_pinsdefines both RMII and MII pins. ?I don't think any board ? would want to configure both sets at the same time. ?Seems like this should ? never get used...Agreed.
Quoted 2 lines
It's also incomplete. ?What about the uPP pin list? ?Or the VPIF? ?Etc.
These should be added as the drivers for these devices are supported.
Quoted 4 lines
I think a board file author should be familiar enough with the SoC to understand what peripheral pins he should be configuring for his/her particular hardware setup and explicitly specify them in the board file.
Agree.
Quoted 4 lines
If you remove the common pin-mux lists and move them to a board file, then once you configure your specific platform, is there any more memory used than with the common scheme? ?Of course, there would be replication of pin-mux code in the board
Quoted 5 lines
There is no memory wastage. All the pin lists are init data.
I too prefer all generic pin lists which are most likely not going to be used at all to be removed. Unused stuff like this will only make code difficult to read.
Quoted 6 lines
FWIW, I agree.
Now, who wants to tackle it?
Kevin
I could but I will need a little help and from all of you. :)
Regards
Victor Rodriguez
Quoted 5 lines
_______________________________________________
Davinci-linux-open-source mailing list
Davinci-linux-open-source at linux.davincidsp.com
http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
Quoted 95 lines · Victor Rodriguez
Quoted 93 lines · Kevin Hilman
Quoted 81 lines · Sekhar
Hi Michael,
Quoted 3 lines · Michael Williamson
Help me out. ?Why do we need generic pin lists?
They might help in cases where all boards will use the same set of pins. For example, every one who uses I2C will most likely both the clock and data pins from the IP. For more complex peripherals with different pins options they serve a documentation purpose at best.
Quoted 3 lines
It seems to me that the "generic pin list" for
da850.cisn't practical for most (if not all) of the peripherals. ?They should be done using__initdatain each board file.Yes, agreed.
Quoted 7 lines
Just a cursory glance at what's in
da850.chighlights several items being set up for the EVM and not generically. ?For example:-
da850_uart1_pinsandda850_uart2_pins: I believe both have RTS/CTS pins which ? for a generic definition should be included as for UART0, but would then ? be unused as the EVM doesn't use these pins in this function.Yes, the generic pin list should have RTS and CTS pins defined for UART1 and UART2. This needs fixing.
Quoted 5 lines
-
da850_mcasp_pins: if generic, must include all 16 AXR pins. ?I think you'd ? be hard pressed to find a board configuration that would use all 16 AXR pins ? for the McASP. ?I'm fairly sure the EVM uses the pins called out, and uses ? other pins for other functions. ?So it's likely this structure wouldn't get used.Yes, the generic pin list should either be completed or removed altogether and the existing pin list
da850_mcasp_pinsshould be copied into the board file and calledda850_evm_mcasp_pins.Quoted 6 lines
-
da850_mmcsd0_pins: includes 2 GPIO pins (specific to the EVM, though possible for ? other boards) for the card detect and write protect signals. ?These pins are ? completely arbitrary for that particular board design. I also believe that ? the complete mmcsd0 port has 4 more data lines as part of it's peripheral, although ? the driver doesn't support using them.This is incorrect again. The generic pin list should be completed (or removed) and the existing list should be copied into the EVM board file as
da850_evm_mmcsd0_pins.Quoted 3 lines
-
da850_emif25_pinsinterface doesn't include the generic pins for some of ? the SDRAM functions.Yes, this should be completed (or removed). This list is unused anyway.
Quoted 4 lines
-
da850_cpgmac_pinsdefines both RMII and MII pins. ?I don't think any board ? would want to configure both sets at the same time. ?Seems like this should ? never get used...Agreed.
Quoted 2 lines
It's also incomplete. ?What about the uPP pin list? ?Or the VPIF? ?Etc.
These should be added as the drivers for these devices are supported.
Quoted 4 lines
I think a board file author should be familiar enough with the SoC to understand what peripheral pins he should be configuring for his/her particular hardware setup and explicitly specify them in the board file.
Agree.
Quoted 4 lines
If you remove the common pin-mux lists and move them to a board file, then once you configure your specific platform, is there any more memory used than with the common scheme? ?Of course, there would be replication of pin-mux code in the board
Quoted 5 lines
There is no memory wastage. All the pin lists are init data.
I too prefer all generic pin lists which are most likely not going to be used at all to be removed. Unused stuff like this will only make code difficult to read.
FWIW, I agree.
Now, who wants to tackle it?
Quoted 9 lines
Quoted 2 lines
Kevin
I could but I will need a little help and from all of you. :)
Regards
Victor Rodriguez
Hey I have sent the first patch in order to fix UARTs on da850. please check if this is right
Regards
Victor Rodriguez
Quoted 6 lines
Quoted 5 lines
_______________________________________________
Davinci-linux-open-source mailing list
Davinci-linux-open-source at linux.davincidsp.com
http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
In reply to vm.rod25 at gmail.comHi Victor,
Quoted 16 lines · On Sat, Nov 13, 2010 at 04:08:50, vm.rod25 at gmail.com wrote:
From: Victor Rodriguez <[email protected]>
This patch defines Pin Mux configuration for MacASP used on the Hawkboard-L138 system in order to add Audio support
Signed-off-by Victor Rodriguez <[email protected]>Tested-by Rene Gonzalez <[email protected]>--- arch/arm/mach-davinci/da850.c | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-)arch/arm/mach-davinci/da850.c +0
-0
arch/arm/mach-davinci/da850.c const short da850_cpgmac_pins[] __initdata = { · line 594
Quoted 5 lines
arch/arm/mach-davinci/da850.c +1
-1@@ -591,7 +591,7 @@ const short da850_cpgmac_pins[] __initdata = {const short da850_mcasp_pins[]__initdata = {DA850_AHCLKX ,DA850_ACLKX ,DA850_AFSX ,DA850_AHCLKR ,DA850_ACLKR ,DA850_AFSR ,DA850_AMUTE , -DA850_AXR_11 ,DA850_AXR_12 , +DA850_AXR_11 ,DA850_AXR_12 ,DA850_AXR_13 ,DA850_AXR_14 ,
To speed up acceptance of this series, can you please drop this patch and submit the rest of the patches as a reduced series?
Audio support can be revisited as a separate patch.
Thanks,
Sekhar
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
Quoted 28 lines · Sekhar
Hi Victor,
Quoted 16 lines · On Sat, Nov 13, 2010 at 04:08:50, vm.rod25 at gmail.com wrote:
From: Victor Rodriguez <[email protected]>
This patch defines Pin Mux configuration for MacASP used on the Hawkboard-L138 system in order to add Audio support
Signed-off-by Victor Rodriguez <[email protected]>Tested-by Rene Gonzalez <[email protected]>---
?arch/arm/mach-davinci/da850.c | ? ?2 +-
?1 files changed, 1 insertions(+), 1 deletions(-)arch/arm/mach-davinci/da850.c +0
-0arch/arm/mach-davinci/da850.c const short da850_cpgmac_pins[] __initdata = { · line 594
Quoted 5 lines
arch/arm/mach-davinci/da850.c +1
-1@@ -591,7 +591,7 @@ const short da850_cpgmac_pins[] __initdata = { ?const short da850_mcasp_pins[] __initdata = { ? ? ? DA850_AHCLKX, DA850_ACLKX, DA850_AFSX, ? ? ? DA850_AHCLKR, DA850_ACLKR, DA850_AFSR, DA850_AMUTE, - ? ? DA850_AXR_11, DA850_AXR_12, + ? ? DA850_AXR_11, DA850_AXR_12, DA850_AXR_13, DA850_AXR_14,To speed up acceptance of this series, can you please drop this patch and submit the rest of the patches as a reduced series?
Quoted 5 lines
Audio support can be revisited as a separate patch.
Thanks,
Sekhar
Yes Sekhar I will do it right now, sorry for the delay with the other patch that fix this
Regards
Victor Rodriguez
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
Quoted 3 lines · Victor Rodriguez
Yes Sekhar I will do it right now, sorry for the delay with the other patch that fix this
The issue was not yours to fix. The generic pin lists need to be cleaned up regardless. So, don't be sorry :)
Thanks,
Sekhar
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
By the way I will eliminate 3 of my patches
[PATCH v8 3/9] davinci: ASoC support for Omapl138-Hawkboard [PATCH v8 4/9] davinci: McASP configuration for Omapl138-Hawkboard [PATCH v8 5/9] davinci: Audio support for Omapl138-Hawkboard
Because if I eliminate the McASP configuration I can not enable the audio support for the board, the kernel compiles and the sound card is recognized but when I try to play any file on the board it will not produce any error but no sound will be produced either
So in order to do not give a wrong support I will eliminate the audio support for hawk board
Regards
Victor Rodriguez
Quoted 12 lines · Sekhar
Quoted 3 lines · Victor Rodriguez
Yes Sekhar I will do it ?right now, sorry for the delay with the other patch that fix this
The issue was not yours to fix. The generic pin lists need to be cleaned up regardless. So, don't be sorry :)
Thanks,
Sekhar
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
In reply to Nori, SekharHello.
Quoted 12 lines · Sekhar
Quoted 10 lines · On Sat, Nov 13, 2010 at 04:08:50, vm.rod25 at gmail.com wrote:
From: Victor Rodriguez <[email protected]>
This patch defines Pin Mux configuration for MacASP used on the Hawkboard-L138 system in order to add Audio support
Signed-off-by Victor Rodriguez <[email protected]>Tested-by Rene Gonzalez <[email protected]>--- arch/arm/mach-davinci/da850.c | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-)
Quoted 13 lines
arch/arm/mach-davinci/da850.c const short da850_cpgmac_pins[] __initdata = { · line 594
Quoted 10 lines
arch/arm/mach-davinci/da850.c +1
-1@@ -591,7 +591,7 @@ const short da850_cpgmac_pins[] __initdata = {const short da850_mcasp_pins[]__initdata = {DA850_AHCLKX ,DA850_ACLKX ,DA850_AFSX ,DA850_AHCLKR ,DA850_ACLKR ,DA850_AFSR ,DA850_AMUTE , -DA850_AXR_11 ,DA850_AXR_12 , +DA850_AXR_11 ,DA850_AXR_12 ,DA850_AXR_13 ,DA850_AXR_14 ,To speed up acceptance of this series, can you please drop this patch and submit the rest of the patches as a reduced series?
BTW, I've seen more AXR pins in DA850, so this patch is far from being
complete anyway.
Quoted 2 lines
Thanks,
Sekhar
WBR, Sergei
PATCH v8 4/9 davinci: McASP configuration for Omapl138-Hawkboard
Quoted 32 lines · Sergei Shtylyov
Hello.
Quoted 13 lines · Sekhar
Quoted 11 lines · On Sat, Nov 13, 2010 at 04:08:50, vm.rod25 at gmail.com wrote:
From: Victor Rodriguez <[email protected]>
This patch defines Pin Mux configuration for MacASP used on the Hawkboard-L138 system in order to add Audio support
Signed-off-by Victor Rodriguez <[email protected]>Tested-by Rene Gonzalez <[email protected]>---
?arch/arm/mach-davinci/da850.c | ? ?2 +-
?1 files changed, 1 insertions(+), 1 deletions(-)Quoted 14 lines
arch/arm/mach-davinci/da850.c const short da850_cpgmac_pins[] __initdata = { · line 594
Quoted 11 lines
arch/arm/mach-davinci/da850.c +1
-1@@ -591,7 +591,7 @@ const short da850_cpgmac_pins[] __initdata = { ?const short da850_mcasp_pins[] __initdata = { ? ? ?DA850_AHCLKX, DA850_ACLKX, DA850_AFSX, ? ? ?DA850_AHCLKR, DA850_ACLKR, DA850_AFSR, DA850_AMUTE, - ? ? DA850_AXR_11, DA850_AXR_12, + ? ? DA850_AXR_11, DA850_AXR_12, DA850_AXR_13, DA850_AXR_14,To speed up acceptance of this series, can you please drop this patch and submit the rest of the patches as a reduced series?
Quoted 2 lines
? BTW, I've seen more AXR pins in DA850, so this patch is far from being complete anyway.
Ok Sergei we will need to work hard on it
By the way is there any other comment to my patches with out this from audio and McASP pins ?
Regards
Victor Rodriguez
Quoted 5 lines
Quoted 2 lines
Thanks,
SekharWBR, Sergei
PATCH v8 5/9 davinci: Audio support for Omapl138-Hawkboard
In reply to a message not in the archiveFrom: Victor Rodriguez <[email protected]>
This patch adds sound support for the Hawkboard-L138 system
---
Notes:
This patch works with da8xx_omapl_defconfig
In order to test ALSA utils select in menuconfig like insmodule:
Sound card support --->
Advanced Linux Sound Architecture --->
ALSA for SoC audio support --->
SoC Audio for the TI DAVINCI chip
SoC Audio support for DA850/OMAP-L138 EVM/Hawkboard
arch/arm/mach-davinci/board-omapl138-hawk.c | 46 +++++++++++++++++++++++++++ 1 files changed, 46 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-omapl138-hawk.c +46 -0
@@ -13,6 +13,7 @@#include <linux/init.h> #include <linux/console.h> #include <linux/gpio.h> +#include <linux/i2c.h> #include <asm/mach-types.h> #include <asm/mach/arch.h>
@@ -110,6 +111,38 @@ static struct edma_rsv_info *da850_edma_rsv[2] = { &da850_edma_cc1_rsv, }; +static struct i2c_board_info __initdata omapl138_hawk_i2c_devices[] = { + { +I2C_BOARD_INFO ("tlv320aic3x" ,0x18 ), + }, +}; + +static struct davinci_i2c_platform_data omapl138_hawk_i2c_0_pdata = { + .bus_freq =100 ,/* kHz */ + .bus_delay =0 ,/* usec */ +}; + +/* davinci Hawkboard audio machine driver */ +static u8 da850_iis_serializer_direction[] = { +INACTIVE_MODE ,INACTIVE_MODE ,INACTIVE_MODE ,INACTIVE_MODE , +INACTIVE_MODE ,INACTIVE_MODE ,INACTIVE_MODE ,INACTIVE_MODE , +INACTIVE_MODE ,INACTIVE_MODE ,INACTIVE_MODE ,INACTIVE_MODE , +INACTIVE_MODE ,TX_MODE ,RX_MODE ,INACTIVE_MODE , +}; + +static struct snd_platform_data omapl138_hawk_snd_data = { + .tx_dma_offset =0x2000 , + .rx_dma_offset =0x2000 , + .op_mode =DAVINCI_MCASP_IIS_MODE , + .num_serializer =ARRAY_SIZE (da850_iis_serializer_direction), + .tdm_slots =2 , + .serial_dir = da850_iis_serializer_direction, + .asp_chan_q =EVENTQ_1 , + .version =MCASP_VERSION_2 , + .txnumevt =1 , + .rxnumevt =1 , +}; +static struct davinci_uart_config omapl138_hawk_uart_config__initdata = { .enabled_uarts =0x7 , };
@@ -127,6 +160,19 @@ static __init void omapl138_hawk_init(void)pr_warning ("%s: EDMA registration failed: %d\n" , __func__, ret); +i2c_register_board_info (1 , omapl138_hawk_i2c_devices, +ARRAY_SIZE (omapl138_hawk_i2c_devices)); + + ret =da8xx_register_i2c (0 , &omapl138_hawk_i2c_0_pdata); +if (ret) +pr_warning ("%s: i2c0 registration failed: %d\n" , + __func__, ret); + + ret =davinci_cfg_reg_list (da850_mcasp_pins); +if (ret) +pr_warning ("%s: mcasp mux setup failed: %d\n" , __func__, ret); +da8xx_register_mcasp (0 , &omapl138_hawk_snd_data); + ret =da8xx_register_watchdog ();if (ret) pr_warning("omapl138_hawk_init: "
Signature · 1 line
1.7.0.4
PATCH v8 6/9 davinci: MMC/SD and USB-OHCI configuration for Omapl138-Hawkboard
In reply to a message not in the archiveFrom: Victor Rodriguez <[email protected]>
This patch defines Pin Mux configuration to enable MMC/SD and USB-OHCI on the Hawkboard-L138 system
--- arch/arm/mach-davinci/da850.c | 4 ++++ arch/arm/mach-davinci/include/mach/mux.h | 4 ++++ 2 files changed, 8 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/da850.c +4 -0
@@ -543,11 +543,15 @@ static const struct mux_config da850_pins[] = { MUX_CFG(DA850, EMA_WAIT_1, 6, 24, 15, 1, false)MUX_CFG (DA850 ,NEMA_CS_2 ,7 ,0 ,15 ,1 , false) /* GPIO function */ + MUX_CFG(DA850, GPIO2_4, 6, 12, 15, 8, false) MUX_CFG(DA850, GPIO2_6, 6, 4, 15, 8, false) MUX_CFG(DA850, GPIO2_8, 5, 28, 15, 8, false) MUX_CFG(DA850, GPIO2_15, 5, 0, 15, 8, false) + MUX_CFG(DA850, GPIO3_12, 7, 12, 15, 8, false) + MUX_CFG(DA850, GPIO3_13, 7, 8, 15, 8, false) MUX_CFG(DA850, GPIO4_0, 10, 28, 15, 8, false) MUX_CFG(DA850, GPIO4_1, 10, 24, 15, 8, false) + MUX_CFG(DA850, GPIO6_13, 13, 8, 15, 8, false) MUX_CFG(DA850, RTC_ALARM, 0, 28, 15, 2, false)#endif };
arch/arm/mach-davinci/include/mach/mux.h +4 -0
@@ -908,11 +908,15 @@ enum davinci_da850_index {DA850_NEMA_CS_2 ,/* GPIO function */ +DA850_GPIO2_4 ,DA850_GPIO2_6 ,DA850_GPIO2_8 ,DA850_GPIO2_15 , +DA850_GPIO3_12 , +DA850_GPIO3_13 ,DA850_GPIO4_0 ,DA850_GPIO4_1 , +DA850_GPIO6_13 , DA850_RTC_ALARM, };
Signature · 1 line
1.7.0.4
PATCH v8 7/9 davinci: MMC/SD support for Omapl138-Hawkboard
In reply to a message not in the archiveFrom: Victor Rodriguez <[email protected]>
This patch adds MMC/SD support for the Hawkboard-L138 system
---
Notes:
This patch works with da8xx_omapl_defconfig
In order to test it select in menuconfig like insmodule
MMC/SD/SDIO card support --->
MMC block device driver
Use bounce buffer for simple hosts TI DAVINCI Multimedia Card Interface support
arch/arm/mach-davinci/board-omapl138-hawk.c | 63 +++++++++++++++++++++++++++ 1 files changed, 63 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-omapl138-hawk.c +63 -0
@@ -23,6 +23,8 @@#include <mach/mux.h> #define HAWKBOARD_PHY_ID "0:07" +#define DA850_HAWK_MMCSD_CD_PIN GPIO_TO_PIN(3, 12) +#define DA850_HAWK_MMCSD_WP_PIN GPIO_TO_PIN(3, 13)static short omapl138_hawk_mii_pins[]__initdata = {DA850_MII_TXEN ,DA850_MII_TXCLK ,DA850_MII_COL ,DA850_MII_TXD_3 ,
@@ -143,6 +145,65 @@ static struct snd_platform_data omapl138_hawk_snd_data = { .rxnumevt = 1, }; +static const short hawk_mmcsd0_pins[] = { +DA850_MMCSD0_DAT_0 ,DA850_MMCSD0_DAT_1 ,DA850_MMCSD0_DAT_2 , +DA850_MMCSD0_DAT_3 ,DA850_MMCSD0_CLK ,DA850_MMCSD0_CMD , +DA850_GPIO3_12 ,DA850_GPIO3_13 , +-1 +}; + +static int da850_hawk_mmc_get_ro (int index) +{ +return gpio_get_value (DA850_HAWK_MMCSD_WP_PIN ); +} + +static int da850_hawk_mmc_get_cd (int index) +{ +return !gpio_get_value (DA850_HAWK_MMCSD_CD_PIN ); +} + +static struct davinci_mmc_config da850_mmc_config = { + .get_ro = da850_hawk_mmc_get_ro, + .get_cd = da850_hawk_mmc_get_cd, + .wires =4 , + .max_freq =50000000 , + .caps =MMC_CAP_MMC_HIGHSPEED |MMC_CAP_SD_HIGHSPEED , + .version =MMC_CTLR_VERSION_2 , +}; + +static __init void omapl138_hawk_mmc_init (void ) +{ +int ret; + + ret =davinci_cfg_reg_list (hawk_mmcsd0_pins); +if (ret) { +pr_warning ("%s: MMC/SD0 mux setup failed: %d\n" , + __func__, ret); +return ; + } + + ret =gpio_request_one (DA850_HAWK_MMCSD_CD_PIN , +GPIOF_DIR_IN ,"MMC CD" ); +if (ret <0 ) { +pr_warning ("%s: can not open GPIO %d\n" , + __func__,DA850_HAWK_MMCSD_CD_PIN ); +return ; + } + + ret =gpio_request_one (DA850_HAWK_MMCSD_WP_PIN , +GPIOF_DIR_IN ,"MMC WP" ); +if (ret <0 ) { +pr_warning ("%s: can not open GPIO %d\n" , + __func__,DA850_HAWK_MMCSD_WP_PIN ); +return ; + } + + ret =da8xx_register_mmcsd0 (&da850_mmc_config); +if (ret) +pr_warning ("%s: MMC/SD0 registration failed: %d\n" , + __func__, ret); +} +static struct davinci_uart_config omapl138_hawk_uart_config__initdata = { .enabled_uarts =0x7 , };
@@ -173,6 +234,8 @@ static __init void omapl138_hawk_init(void)pr_warning ("%s: mcasp mux setup failed: %d\n" , __func__, ret);da8xx_register_mcasp (0 , &omapl138_hawk_snd_data); +omapl138_hawk_mmc_init (); + ret =da8xx_register_watchdog ();if (ret) pr_warning("omapl138_hawk_init: "
Signature · 1 line
1.7.0.4
PATCH v8 8/9 davinci: USB clocks for Omapl138-Hawkboard
In reply to a message not in the archiveFrom: Victor Rodriguez <[email protected]>
This patch adds USB1.1 and USB2.0 clocks for the Hawkboard-L138 system
--- arch/arm/mach-davinci/da850.c | 16 ++++++++++++++++ 1 files changed, 16 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/da850.c +16 -0
@@ -345,6 +345,20 @@ static struct clk aemif_clk = { .flags = ALWAYS_ENABLED, }; +static struct clk usb11_clk = { + .name ="usb11" , + .parent = &pll0_sysclk4, + .lpsc =DA8XX_LPSC1_USB11 , + .gpsc =1 , +}; + +static struct clk usb20_clk = { + .name ="usb20" , + .parent = &pll0_sysclk2, + .lpsc =DA8XX_LPSC1_USB20 , + .gpsc =1 , +}; +static struct clk_lookup da850_clks[] = {CLK (NULL ,"ref" , &ref_clk),CLK (NULL ,"pll0" , &pll0_clk),
@@ -387,6 +401,8 @@ static struct clk_lookup da850_clks[] = {CLK ("davinci_mmc.0" ,NULL , &mmcsd0_clk),CLK ("davinci_mmc.1" ,NULL , &mmcsd1_clk),CLK (NULL ,"aemif" , &aemif_clk), +CLK (NULL ,"usb11" , &usb11_clk), +CLK (NULL ,"usb20" , &usb20_clk), CLK(NULL, NULL, NULL), };
Signature · 1 line
1.7.0.4
PATCH v8 9/9 davinci: USB1.1 support for Omapl138-Hawkboard
In reply to a message not in the archiveFrom: Victor Rodriguez <[email protected]>
This patch adds USB1.1 support for the Hawkboard-L138 system
---
Notes:
This patch works with da8xx_omapl_defconfig
In order to test it select in menuconfig like insmodule
Device Drivers --->
SCSI device support --->
SCSI device support
legacy /proc/scsi/ support
SCSI disk support
SCSI low-level drivers
USB support --->
Support for Host-side USB OHCI HCD support (NEW)
USB Mass Storage support (NEW) USB Gadget Support --->
USB Gadget Drivers (Ethernet Gadget\
(with CDC Ethernet support)) --->
NOP USB Transceiver Driver
And you will be able to mount and USB pen drive
In order to connect a keyboard or a mouse on a USB-hub select in menuconfig like insmodule
HID Devices --->
Generic HID support
USB Human Interface Device (full HID) support
arch/arm/mach-davinci/board-omapl138-hawk.c | 106 +++++++++++++++++++++++++++ 1 files changed, 106 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-omapl138-hawk.c +106 -0
@@ -26,6 +26,9 @@#define DA850_HAWK_MMCSD_CD_PIN GPIO_TO_PIN(3, 12)#define DA850_HAWK_MMCSD_WP_PIN GPIO_TO_PIN(3, 13) +#define DA850_USB1_VBUS_PIN GPIO_TO_PIN(2, 4) +#define DA850_USB1_OC_PIN GPIO_TO_PIN(6, 13) +static short omapl138_hawk_mii_pins[]__initdata = {DA850_MII_TXEN ,DA850_MII_TXCLK ,DA850_MII_COL ,DA850_MII_TXD_3 ,DA850_MII_TXD_2 ,DA850_MII_TXD_1 ,DA850_MII_TXD_0 ,DA850_MII_RXER ,
@@ -204,6 +207,107 @@ static __init void omapl138_hawk_mmc_init(void) __func__, ret); } +static irqreturn_t omapl138_hawk_usb_ocic_irq (int irq,void *dev_id); +static da8xx_ocic_handler_t hawk_usb_ocic_handler; + +static const short da850_hawk_usb11_pins[] = { +DA850_GPIO2_4 ,DA850_GPIO6_13 , +-1 +}; + +static int hawk_usb_set_power (unsigned port,int on) +{ +gpio_set_value (DA850_USB1_VBUS_PIN , on); +return 0 ; +} + +static int hawk_usb_get_power (unsigned port) +{ +return gpio_get_value (DA850_USB1_VBUS_PIN ); +} + +static int hawk_usb_get_oci (unsigned port) +{ +return !gpio_get_value (DA850_USB1_OC_PIN ); +} + +static int hawk_usb_ocic_notify (da8xx_ocic_handler_t handler) +{ +int irq =gpio_to_irq (DA850_USB1_OC_PIN ); +int error =0 ; + +if (handler !=NULL ) { + hawk_usb_ocic_handler = handler; + + error =request_irq (irq, omapl138_hawk_usb_ocic_irq, +IRQF_DISABLED |IRQF_TRIGGER_RISING | +IRQF_TRIGGER_FALLING , +"OHCI over-current indicator" ,NULL ); +if (error) +pr_err (KERN_ERR "%s: could not request IRQ to watch " +"over-current indicator changes\n" , __func__); + }else { +free_irq (irq,NULL ); + } +return error; +} + +static struct da8xx_ohci_root_hub omapl138_hawk_usb11_pdata = { + .set_power = hawk_usb_set_power, + .get_power = hawk_usb_get_power, + .get_oci = hawk_usb_get_oci, + .ocic_notify = hawk_usb_ocic_notify, +/* TPS2087 switch @ 5V */ + .potpgt = (3 +1 ) /2 ,/* 3 ms max */ +}; + +static irqreturn_t omapl138_hawk_usb_ocic_irq (int irq,void *dev_id) +{ +hawk_usb_ocic_handler (&omapl138_hawk_usb11_pdata,1 ); +return IRQ_HANDLED ; +} + +static __init void omapl138_hawk_usb_init (void ) +{ +int ret; +u32 cfgchip2; + + ret =davinci_cfg_reg_list (da850_hawk_usb11_pins); +if (ret) { +pr_warning ("%s: USB 1.1 PinMux setup failed: %d\n" , + __func__, ret); +return ; + } + +/* Setup the Ref. clock frequency for the HAWK at 24 MHz. */ + + cfgchip2 =__raw_readl (DA8XX_SYSCFG0_VIRT (DA8XX_CFGCHIP2_REG )); + cfgchip2 &= ~CFGCHIP2_REFFREQ ; + cfgchip2 |=CFGCHIP2_REFFREQ_24MHZ ; +__raw_writel (cfgchip2,DA8XX_SYSCFG0_VIRT (DA8XX_CFGCHIP2_REG )); + + ret =gpio_request_one (DA850_USB1_VBUS_PIN , +GPIOF_DIR_OUT ,"USB1 VBUS" ); +if (ret <0 ) { +pr_err (KERN_ERR "%s: failed to request GPIO for USB 1.1 port " +"power control: %d\n" , __func__, ret); +return ; + } + + ret =gpio_request_one (DA850_USB1_OC_PIN , +GPIOF_DIR_IN ,"USB1 OC" ); +if (ret <0 ) { +pr_err (KERN_ERR "%s: failed to request GPIO for USB 1.1 port " +"over-current indicator: %d\n" , __func__, ret); +return ; + } + + ret =da8xx_register_usb11 (&omapl138_hawk_usb11_pdata); +if (ret) +pr_warning ("%s: USB 1.1 registration failed: %d\n" , + __func__, ret); +} +static struct davinci_uart_config omapl138_hawk_uart_config__initdata = { .enabled_uarts =0x7 , };
@@ -236,6 +340,8 @@ static __init void omapl138_hawk_init(void)omapl138_hawk_mmc_init (); +omapl138_hawk_usb_init (); + ret =da8xx_register_watchdog ();if (ret) pr_warning("omapl138_hawk_init: "
Signature · 1 line
1.7.0.4