Skip to contentSkip to conversation

tnetv107x ssp drivers

PATCH Superseded Cyril Chemparathy 5 participants 22 messages Nov 19, 2010 – Nov 22, 2010

Subsystems (9)

v6 of 8 Superseded Latest is v8 →

lore
Share & tools
lore
#0 lore raw

v6 cover tnetv107x ssp drivers

TI's sequencer serial port (TI-SSP) is a jack-of-all-trades type of serial port device. It has a built-in programmable execution engine that can be programmed to operate as almost any serial bus (I2C, SPI, EasyScale, and others).

This patch series implements a driver stack that looks like the following:

                             +--------+
                             | eeprom | . . .
                             +--------+
   +-----------+             +--------------+ +---------+
   | regulator | . . .       |   i2c-gpio   | | 1-wire  | . . .
   +-----------+             +--------------+ +---------+
   +----------------------+  +--------------------------------+
   |       ssp-spi        |  |           ssp-gpio             |
   +----------------------+  +--------------------------------+
   +----------------------------------------------------------+
   |                            ssp                           |
   +----------------------------------------------------------+

Changes between v6 and v5 of this series:
- Changed initcalls to module_init() across all drivers. This series now uses a late_initcall() in the board to delay initialization of gpio and regulator dependent devices.

Changes between v5 and v4 of this series:
- Moved drivers from misc/gpio/spi to mfd
- Removed implicit init-time iosel setup
- Minor cleanups in backlight driver

Changes between v3 and v4 of this series:
- Replaced polled wait for sequence termination with interrupt
- Improved locking within SSP driver
- Other minor cleanups

Changes between v2 and v3 of this series:
- Minor cleanups in Kconfig and Makefile ordering

Changes between v1 and v2 of this series:
- Replaced open()/close() semantics with dynamic platform_device registration on SSP probe.
- Removed user-land interface to regulator registers
- More sensible regulator constraints
- Other minor cleanups

Cyril Chemparathy (12):
misc: add driver for sequencer serial port
davinci: add tnetv107x ssp platform device
davinci: add ssp config for tnetv107x evm board
spi: add ti-ssp spi master driver
davinci: add spi devices on tnetv107x evm
regulator: add driver for tps6524x regulator
davinci: add tnetv107x evm regulators
gpio: add ti-ssp gpio driver
davinci: add tnetv107x evm ti-ssp gpio device
backlight: add support for tps6116x controller
davinci: add tnetv107x evm backlight device
davinci: add tnetv107x evm i2c eeprom device

 arch/arm/mach-davinci/board-tnetv107x-evm.c    |  197 +++++++
 arch/arm/mach-davinci/devices-tnetv107x.c      |   25 +
 arch/arm/mach-davinci/include/mach/tnetv107x.h |    2 +
 arch/arm/mach-davinci/tnetv107x.c              |    2 +-
 drivers/gpio/Kconfig                           |   10 +
 drivers/gpio/Makefile                          |    1 +
 drivers/gpio/ti-ssp-gpio.c                     |  206 +++++++
 drivers/mfd/Kconfig                            |   11 +
 drivers/mfd/Makefile                           |    1 +
 drivers/mfd/ti-ssp.c                           |  472 ++++++++++++++++
 drivers/regulator/Kconfig                      |   10 +
 drivers/regulator/Makefile                     |    1 +
 drivers/regulator/tps6524x-regulator.c         |  692 ++++++++++++++++++++++++
 drivers/spi/Kconfig                            |   10 +
 drivers/spi/Makefile                           |    1 +
 drivers/spi/ti-ssp-spi.c                       |  402 ++++++++++++++
 drivers/video/backlight/Kconfig                |    7 +
 drivers/video/backlight/Makefile               |    2 +-
 drivers/video/backlight/tps6116x.c             |  298 ++++++++++
 include/linux/mfd/ti_ssp.h                     |   97 ++++
 20 files changed, 2445 insertions(+), 2 deletions(-)
 create mode 100644 drivers/gpio/ti-ssp-gpio.c
 create mode 100644 drivers/mfd/ti-ssp.c
 create mode 100644 drivers/regulator/tps6524x-regulator.c
 create mode 100644 drivers/spi/ti-ssp-spi.c
 create mode 100644 drivers/video/backlight/tps6116x.c
 create mode 100644 include/linux/mfd/ti_ssp.h
#1 lore raw

PATCH v6 1/12 misc: add driver for sequencer serial port

TI's sequencer serial port (TI-SSP) is a jack-of-all-trades type of serial port device. It has a built-in programmable execution engine that can be programmed to operate as almost any serial bus (I2C, SPI, EasyScale, and others).

This patch adds a driver for this controller device. The driver does not expose a user-land interface. Protocol drivers built on top of this layer are expected to remain in-kernel.

---
 drivers/mfd/Kconfig        |   11 +
 drivers/mfd/Makefile       |    1 +
 drivers/mfd/ti-ssp.c       |  472 ++++++++++++++++++++++++++++++++++++++++++++
 include/linux/mfd/ti_ssp.h |   87 ++++++++
 4 files changed, 571 insertions(+), 0 deletions(-)
 create mode 100644 drivers/mfd/ti-ssp.c
 create mode 100644 include/linux/mfd/ti_ssp.h
drivers/mfd/Kconfig +11 -0
index 3a1493b..a4b4b70 100644
@@ -81,6 +81,17 @@ config MFD_DM355EVM_MSP
 	  boards.  MSP430 firmware manages resets and power sequencing,
 	  inputs from buttons and the IR remote, LEDs, an RTC, and more.
 
+config MFD_TI_SSP
+	tristate "TI Sequencer Serial Port support"
+	depends on ARCH_DAVINCI_TNETV107X
+	select MFD_CORE
+	---help---
+	  Say Y here if you want support for the Sequencer Serial Port
+	  in a Texas Instruments TNETV107X SoC.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ti-ssp.
+
 config HTC_EGPIO
 	bool "HTC EGPIO support"
 	depends on GENERIC_HARDIRQS && GPIOLIB && ARM
drivers/mfd/Makefile +1 -0
index f54b365..f64cf13 100644
@@ -14,6 +14,7 @@ obj-$(CONFIG_HTC_I2CPLD)	+= htc-i2cpld.o
 
 obj-$(CONFIG_MFD_DAVINCI_VOICECODEC)	+= davinci_voicecodec.o
 obj-$(CONFIG_MFD_DM355EVM_MSP)	+= dm355evm_msp.o
+obj-$(CONFIG_MFD_TI_SSP)	+= ti-ssp.o
 
 obj-$(CONFIG_MFD_STMPE)		+= stmpe.o
 obj-$(CONFIG_MFD_TC35892)	+= tc35892.o
drivers/mfd/ti-ssp.c new file +472 -0

472 lines not on this page · raw message

include/linux/mfd/ti_ssp.h new file +87 -0

87 lines not on this page · raw message

Signature · 1 line
1.7.1
#2 lore raw

PATCH v6 2/12 davinci: add tnetv107x ssp platform device

In reply to Cyril Chemparathy

This patch adds an SSP platform device definition for the tnetv107x soc family. The clock lookup entry has also been updated to match.

---
 arch/arm/mach-davinci/devices-tnetv107x.c      |   25 ++++++++++++++++++++++++
 arch/arm/mach-davinci/include/mach/tnetv107x.h |    2 +
 arch/arm/mach-davinci/tnetv107x.c              |    2 +-
 3 files changed, 28 insertions(+), 1 deletions(-)
arch/arm/mach-davinci/devices-tnetv107x.c +25 -0
index 85503de..6162cae 100644
@@ -35,6 +35,7 @@
 #define TNETV107X_SDIO0_BASE			0x08088700
 #define TNETV107X_SDIO1_BASE			0x08088800
 #define TNETV107X_KEYPAD_BASE			0x08088a00
+#define TNETV107X_SSP_BASE			0x08088c00
 #define TNETV107X_ASYNC_EMIF_CNTRL_BASE		0x08200000
 #define TNETV107X_ASYNC_EMIF_DATA_CE0_BASE	0x30000000
 #define TNETV107X_ASYNC_EMIF_DATA_CE1_BASE	0x40000000
@@ -342,6 +343,25 @@ static struct platform_device tsc_device = {
 	.resource	= tsc_resources,
 };
 
+static struct resource ssp_resources[] = {
+	{
+		.start	= TNETV107X_SSP_BASE,
+		.end	= TNETV107X_SSP_BASE + 0x1ff,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.start	= IRQ_TNETV107X_SSP,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device ssp_device = {
+	.name		= "ti-ssp",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(ssp_resources),
+	.resource	= ssp_resources,
+};
+
 void __init tnetv107x_devices_init(struct tnetv107x_device_info *info)
 {
 	int i, error;
@@ -380,4 +400,9 @@ void __init tnetv107x_devices_init(struct tnetv107x_device_info *info)
 		keypad_device.dev.platform_data = info->keypad_config;
 		platform_device_register(&keypad_device);
 	}
+
+	if (info->ssp_config) {
+		ssp_device.dev.platform_data = info->ssp_config;
+		platform_device_register(&ssp_device);
+	}
 }
arch/arm/mach-davinci/include/mach/tnetv107x.h +2 -0
index 5a681d8..89c1fdc 100644
@@ -34,6 +34,7 @@
 
 #include <linux/serial_8250.h>
 #include <linux/input/matrix_keypad.h>
+#include <linux/mfd/ti_ssp.h>
 
 #include <mach/mmc.h>
 #include <mach/nand.h>
@@ -44,6 +45,7 @@ struct tnetv107x_device_info {
 	struct davinci_mmc_config	*mmc_config[2];  /* 2 controllers */
 	struct davinci_nand_pdata	*nand_config[4]; /* 4 chipsels */
 	struct matrix_keypad_platform_data *keypad_config;
+	struct ti_ssp_data		*ssp_config;
 };
 
 extern struct platform_device tnetv107x_wdt_device;
arch/arm/mach-davinci/tnetv107x.c +1 -1
index 6fcdece..1b28fdd 100644
@@ -278,7 +278,7 @@ static struct clk_lookup clks[] = {
 	CLK(NULL,		"timer1",		&clk_timer1),
 	CLK("tnetv107x_wdt.0",	NULL,			&clk_wdt_arm),
 	CLK(NULL,		"clk_wdt_dsp",		&clk_wdt_dsp),
-	CLK("ti-ssp.0",		NULL,			&clk_ssp),
+	CLK("ti-ssp",		NULL,			&clk_ssp),
 	CLK(NULL,		"clk_tdm0",		&clk_tdm0),
 	CLK(NULL,		"clk_vlynq",		&clk_vlynq),
 	CLK(NULL,		"clk_mcdma",		&clk_mcdma),
Signature · 1 line
1.7.1
#3 lore raw

PATCH v6 3/12 davinci: add ssp config for tnetv107x evm board

In reply to Cyril Chemparathy

This patch adds SSP configuration and pin muxing info for tnetv107x evm boards.

---
 arch/arm/mach-davinci/board-tnetv107x-evm.c |   14 ++++++++++++++
 1 files changed, 14 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +14 -0
index a6db854..ef526b1 100644
@@ -99,6 +99,12 @@ static const short uart1_pins[] __initdata = {
 	-1
 };
 
+static const short ssp_pins[] __initdata = {
+	TNETV107X_SSP0_0, TNETV107X_SSP0_1, TNETV107X_SSP0_2,
+	TNETV107X_SSP1_0, TNETV107X_SSP1_1, TNETV107X_SSP1_2,
+	TNETV107X_SSP1_3, -1
+};
+
 static struct mtd_partition nand_partitions[] = {
 	/* bootloader (U-Boot, etc) in first 12 sectors */
 	{
@@ -196,17 +202,25 @@ static struct matrix_keypad_platform_data keypad_config = {
 	.no_autorepeat	= 0,
 };
 
+static struct ti_ssp_data ssp_config = {
+	.out_clock	= 250 * 1000,
+	.dev_data	= {
+	},
+};
+
 static struct tnetv107x_device_info evm_device_info __initconst = {
 	.serial_config		= &serial_config,
 	.mmc_config[1]		= &mmc_config,	/* controller 1 */
 	.nand_config[0]		= &nand_config,	/* chip select 0 */
 	.keypad_config		= &keypad_config,
+	.ssp_config		= &ssp_config,
 };
 
 static __init void tnetv107x_evm_board_init(void)
 {
 	davinci_cfg_reg_list(sdio1_pins);
 	davinci_cfg_reg_list(uart1_pins);
+	davinci_cfg_reg_list(ssp_pins);
 
 	tnetv107x_devices_init(&evm_device_info);
 }
Signature · 1 line
1.7.1
#4 lore raw

PATCH v6 4/12 spi: add ti-ssp spi master driver

In reply to Cyril Chemparathy

This patch adds an SPI master implementation that operates on top of an underlying TI-SSP port.

---
 drivers/spi/Kconfig        |   10 +
 drivers/spi/Makefile       |    1 +
 drivers/spi/ti-ssp-spi.c   |  402 ++++++++++++++++++++++++++++++++++++++++++++
 include/linux/mfd/ti_ssp.h |    6 +
 4 files changed, 419 insertions(+), 0 deletions(-)
 create mode 100644 drivers/spi/ti-ssp-spi.c
drivers/spi/Kconfig +10 -0
index 78f9fd0..7f0ed2a 100644
@@ -336,6 +336,16 @@ config SPI_TEGRA
 	help
 	  SPI driver for NVidia Tegra SoCs
 
+config SPI_TI_SSP
+	tristate "TI Sequencer Serial Port - SPI Support"
+	depends on MFD_TI_SSP
+	help
+	  This selects an SPI master implementation using a TI sequencer
+	  serial port.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ti-ssp-spi.
+
 config SPI_TOPCLIFF_PCH
 	tristate "Topcliff PCH SPI Controller"
 	depends on PCI
drivers/spi/Makefile +1 -0
index 8bc1a5a..595e5b8 100644
@@ -40,6 +40,7 @@ obj-$(CONFIG_SPI_S3C24XX_GPIO)		+= spi_s3c24xx_gpio.o
 obj-$(CONFIG_SPI_S3C24XX)		+= spi_s3c24xx_hw.o
 obj-$(CONFIG_SPI_S3C64XX)		+= spi_s3c64xx.o
 obj-$(CONFIG_SPI_TEGRA)			+= spi_tegra.o
+obj-$(CONFIG_SPI_TI_SSP)		+= ti-ssp-spi.o
 obj-$(CONFIG_SPI_TOPCLIFF_PCH)		+= spi_topcliff_pch.o
 obj-$(CONFIG_SPI_TXX9)			+= spi_txx9.o
 obj-$(CONFIG_SPI_XILINX)		+= xilinx_spi.o
drivers/spi/ti-ssp-spi.c new file +402 -0

402 lines not on this page · raw message

include/linux/mfd/ti_ssp.h +6 -0
index 021fe09..dbb4b43 100644
@@ -32,6 +32,12 @@ struct ti_ssp_data {
 	struct ti_ssp_dev_data	dev_data[2];
 };
 
+struct ti_ssp_spi_data {
+	unsigned long	iosel;
+	int		num_cs;
+	void		(*select)(int cs);
+};
+
 /*
  * Sequencer port IO pin configuration bits.  These do not correlate 1-1 with
  * the hardware.  The iosel field in the port data combines iosel1 and iosel2,
Signature · 1 line
1.7.1
#5 lore raw

PATCH v6 5/12 davinci: add spi devices on tnetv107x evm

In reply to Cyril Chemparathy

This patch adds definitions for spi devices on the tnetv107x evm platform.

---
 arch/arm/mach-davinci/board-tnetv107x-evm.c |   43 +++++++++++++++++++++++++++
 1 files changed, 43 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +43 -0
index ef526b1..1a656e8 100644
@@ -25,6 +25,7 @@
 #include <linux/mtd/partitions.h>
 #include <linux/input.h>
 #include <linux/input/matrix_keypad.h>
+#include <linux/spi/spi.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach-types.h>
@@ -37,6 +38,7 @@
 
 #define EVM_MMC_WP_GPIO		21
 #define EVM_MMC_CD_GPIO		24
+#define EVM_SPI_CS_GPIO		54
 
 static int initialize_gpio(int gpio, char *desc)
 {
@@ -202,9 +204,45 @@ static struct matrix_keypad_platform_data keypad_config = {
 	.no_autorepeat	= 0,
 };
 
+static void spi_select_device(int cs)
+{
+	static int gpio;
+
+	if (!gpio) {
+		int ret;
+		ret = gpio_request(EVM_SPI_CS_GPIO, "spi chipsel");
+		if (ret < 0) {
+			pr_err("cannot open spi chipsel gpio\n");
+			gpio = -ENOSYS;
+			return;
+		} else {
+			gpio = EVM_SPI_CS_GPIO;
+			gpio_direction_output(gpio, 0);
+		}
+	}
+
+	if (gpio < 0)
+		return;
+
+	return gpio_set_value(gpio, cs ? 1 : 0);
+}
+
+static struct ti_ssp_spi_data spi_master_data = {
+	.num_cs	= 2,
+	.select	= spi_select_device,
+	.iosel	= SSP_PIN_SEL(0, SSP_CLOCK)	| SSP_PIN_SEL(1, SSP_DATA) |
+		  SSP_PIN_SEL(2, SSP_CHIPSEL)	| SSP_PIN_SEL(3, SSP_IN)   |
+		  SSP_INPUT_SEL(3),
+};
+
 static struct ti_ssp_data ssp_config = {
 	.out_clock	= 250 * 1000,
 	.dev_data	= {
+		[1] = {
+			.dev_name = "ti-ssp-spi",
+			.pdata = &spi_master_data,
+			.pdata_size = sizeof(spi_master_data),
+		},
 	},
 };
 
@@ -216,6 +254,9 @@ static struct tnetv107x_device_info evm_device_info __initconst = {
 	.ssp_config		= &ssp_config,
 };
 
+static struct spi_board_info spi_info[] __initconst = {
+};
+
 static __init void tnetv107x_evm_board_init(void)
 {
 	davinci_cfg_reg_list(sdio1_pins);
@@ -223,6 +264,8 @@ static __init void tnetv107x_evm_board_init(void)
 	davinci_cfg_reg_list(ssp_pins);
 
 	tnetv107x_devices_init(&evm_device_info);
+
+	spi_register_board_info(spi_info, ARRAY_SIZE(spi_info));
 }
 
 #ifdef CONFIG_SERIAL_8250_CONSOLE
Signature · 1 line
1.7.1
#6 lore raw

PATCH v6 5/12 davinci: add spi devices on tnetv107x evm

Hello.

Quoted 11 lines · Cyril Chemparathy

This patch adds definitions for spi devices on the tnetv107x evm platform.

---
 arch/arm/mach-davinci/board-tnetv107x-evm.c |   43 +++++++++++++++++++++++++++
 1 files changed, 43 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +0 -0
index ef526b1..1a656e8 100644

[...]

arch/arm/mach-davinci/board-tnetv107x-evm.c static struct matrix_keypad_platform_data keypad_config = { · line 213

Quoted 11 lines
arch/arm/mach-davinci/board-tnetv107x-evm.c +7 -0
@@ -202,9 +204,45 @@ static struct matrix_keypad_platform_data keypad_config = {
 	.no_autorepeat	= 0,
 };
 
+static void spi_select_device(int cs)
+{
+	static int gpio;
+
+	if (!gpio) {
+		int ret;
+		ret = gpio_request(EVM_SPI_CS_GPIO, "spi chipsel");

Why not just:

int ret = gpio_request(EVM_SPI_CS_GPIO, "spi chipsel");

Also, and empty line after declaration wouldn't hurt.

Quoted 4 lines
arch/arm/mach-davinci/board-tnetv107x-evm.c +4 -0
+		if (ret < 0) {
+			pr_err("cannot open spi chipsel gpio\n");
+			gpio = -ENOSYS;
+			return;

arch/arm/mach-davinci/board-tnetv107x-evm.c static struct matrix_keypad_platform_data keypad_config = { · line 227

Quoted 10 lines
arch/arm/mach-davinci/board-tnetv107x-evm.c +10 -0
+		} else {
+			gpio = EVM_SPI_CS_GPIO;
+			gpio_direction_output(gpio, 0);
+		}
+	}
+
+	if (gpio < 0)
+		return;
+
+	return gpio_set_value(gpio, cs ? 1 : 0);

Why not do it right with gpio_direction_output() call?

WBR, Sergei

#7 lore raw

PATCH v6 5/12 davinci: add spi devices on tnetv107x evm

On 11/19/2010 11:25 AM, Sergei Shtylyov wrote:
[...]

Quoted 8 lines

arch/arm/mach-davinci/board-tnetv107x-evm.c static struct matrix_keypad_platform_data keypad_config = { · line 213

Quoted 1 line
arch/arm/mach-davinci/board-tnetv107x-evm.c +1 -0
+		ret = gpio_request(EVM_SPI_CS_GPIO, "spi chipsel");

Why not just:

int ret = gpio_request(EVM_SPI_CS_GPIO, "spi chipsel");

Also, and empty line after declaration wouldn't hurt.

[...]

Quoted 3 lines

arch/arm/mach-davinci/board-tnetv107x-evm.c static struct matrix_keypad_platform_data keypad_config = { · line 227

Quoted 1 line
arch/arm/mach-davinci/board-tnetv107x-evm.c +1 -0
+	return gpio_set_value(gpio, cs ? 1 : 0);

Why not do it right with gpio_direction_output() call?

Sure. I might as well change to use gpio_request_one() while I'm at it.

If I get enough comments to warrant another revision of this series, I will put in this change at the time. Otherwise, I'd rather roll this in with other patches on my pending list. Is that ok?

Thanks for taking a look, Sergei.

Regards
- Cyril.

#8 lore raw

PATCH v6 6/12 regulator: add driver for tps6524x regulator

In reply to Cyril Chemparathy

TPS6524X provides three step-down converters and two general-purpose LDO voltage regulators. This device is interfaced using SPI.

---
 drivers/regulator/Kconfig              |   10 +
 drivers/regulator/Makefile             |    1 +
 drivers/regulator/tps6524x-regulator.c |  692 ++++++++++++++++++++++++++++++++
 3 files changed, 703 insertions(+), 0 deletions(-)
 create mode 100644 drivers/regulator/tps6524x-regulator.c
drivers/regulator/Kconfig +10 -0
index dd30e88..da34981 100644
@@ -250,5 +250,15 @@ config REGULATOR_TPS6586X
 	help
 	  This driver supports TPS6586X voltage regulator chips.
 
+config REGULATOR_TPS6524X
+	tristate "TI TPS6524X Power regulators"
+	depends on SPI
+	help
+	  This driver supports TPS6524X voltage regulator chips. TPS6524X
+	  provides three step-down converters and two general-purpose LDO
+	  voltage regulators.  This device is interfaced using a customized
+	  serial interface currently supported on the sequencer serial
+	  port controller.
+
 endif
 
drivers/regulator/Makefile +1 -0
index bff8157..cf71df7 100644
@@ -34,6 +34,7 @@ obj-$(CONFIG_REGULATOR_AB3100) += ab3100.o
 
 obj-$(CONFIG_REGULATOR_TPS65023) += tps65023-regulator.o
 obj-$(CONFIG_REGULATOR_TPS6507X) += tps6507x-regulator.o
+obj-$(CONFIG_REGULATOR_TPS6524X) += tps6524x-regulator.o
 obj-$(CONFIG_REGULATOR_88PM8607) += 88pm8607.o
 obj-$(CONFIG_REGULATOR_ISL6271A) += isl6271a-regulator.o
 obj-$(CONFIG_REGULATOR_AB8500)	+= ab8500.o
drivers/regulator/tps6524x-regulator.c new file +692 -0

692 lines not on this page · raw message

Signature · 1 line
1.7.1
#9 lore raw

PATCH v6 7/12 davinci: add tnetv107x evm regulators

In reply to Cyril Chemparathy

This patch adds regulator and spi board info definitions for the tps6524x power management IC found on tnetv107x evm boards.

---
 arch/arm/mach-davinci/board-tnetv107x-evm.c |   85 +++++++++++++++++++++++++++
 1 files changed, 85 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +85 -0
index 1a656e8..ca23516 100644
@@ -26,6 +26,9 @@
 #include <linux/input.h>
 #include <linux/input/matrix_keypad.h>
 #include <linux/spi/spi.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/consumer.h>
+#include <linux/regulator/driver.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach-types.h>
@@ -254,7 +257,89 @@ static struct tnetv107x_device_info evm_device_info __initconst = {
 	.ssp_config		= &ssp_config,
 };
 
+static struct regulator_consumer_supply usb_consumers[] = {
+	REGULATOR_SUPPLY("vbus", "musb_hdrc.1"),
+};
+
+static struct regulator_consumer_supply lcd_consumers[] = {
+	REGULATOR_SUPPLY("vlcd", "tps6116x"),
+};
+
+static struct regulator_init_data regulators[] = {
+	{
+		.constraints		= {
+			.name		= "DCDC1",
+			.min_uV		= 1000000,
+			.max_uV		= 1000000,
+			.always_on	= 1,
+			.boot_on	= 1,
+		},
+	},
+	{
+		.constraints		= {
+			.name		= "DCDC2",
+			.min_uV		= 1800000,
+			.max_uV		= 1800000,
+			.always_on	= 1,
+			.boot_on	= 1,
+		},
+	},
+	{
+		.constraints		= {
+			.name		= "DCDC3",
+			.min_uV		= 3300000,
+			.max_uV		= 3300000,
+			.always_on	= 1,
+			.boot_on	= 1,
+		},
+	},
+	{
+		.constraints		= {
+			.name		= "LDO1",
+			.min_uV		= 4800000,
+			.max_uV		= 4800000,
+			.always_on	= 1,
+			.boot_on	= 1,
+		},
+	},
+	{
+		.constraints		= {
+			.name		= "LDO1",
+			.min_uV		= 3300000,
+			.max_uV		= 3300000,
+			.always_on	= 1,
+			.boot_on	= 1,
+		},
+	},
+	{
+		.num_consumer_supplies	= ARRAY_SIZE(usb_consumers),
+		.consumer_supplies	= usb_consumers,
+		.constraints		= {
+			.name		= "USB",
+			.min_uA		= 200000,
+			.max_uA		= 1000000,
+			.valid_ops_mask	= REGULATOR_CHANGE_CURRENT |
+					  REGULATOR_CHANGE_STATUS,
+		},
+	},
+	{
+		.num_consumer_supplies	= ARRAY_SIZE(lcd_consumers),
+		.consumer_supplies	= lcd_consumers,
+		.constraints		= {
+			.name		= "LCD",
+			.valid_ops_mask	= REGULATOR_CHANGE_STATUS,
+		},
+	},
+};
+
 static struct spi_board_info spi_info[] __initconst = {
+	{
+		.modalias	= "tps6524x",
+		.bus_num	= 1,
+		.chip_select	= 0,
+		.mode		= SPI_MODE_0,
+		.platform_data	= regulators,
+	},
 };
 
 static __init void tnetv107x_evm_board_init(void)
Signature · 1 line
1.7.1
#10 lore raw

PATCH v6 8/12 gpio: add ti-ssp gpio driver

In reply to Cyril Chemparathy

TI's SSP controller pins can be directly read and written to behave like a GPIO. This patch adds a GPIO driver that exposes such functionality.

---
 drivers/gpio/Kconfig       |   10 ++
 drivers/gpio/Makefile      |    1 +
 drivers/gpio/ti-ssp-gpio.c |  206 ++++++++++++++++++++++++++++++++++++++++++++
 include/linux/mfd/ti_ssp.h |    4 +
 4 files changed, 221 insertions(+), 0 deletions(-)
 create mode 100644 drivers/gpio/ti-ssp-gpio.c
drivers/gpio/Kconfig +10 -0
index 3143ac7..05bbe4c 100644
@@ -128,6 +128,16 @@ config GPIO_VX855
 	  additional drivers must be enabled in order to use the
 	  functionality of the device.
 
+config GPIO_TI_SSP
+	tristate "TI Sequencer Serial Port - GPIO Support"
+	depends on MFD_TI_SSP
+	help
+	  Say yes here to support a GPIO interface on TI SSP port pins.
+	  Each SSP port translates into 4 GPIOs.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called ti-ssp-gpio.
+
 comment "I2C GPIO expanders:"
 
 config GPIO_MAX7300
drivers/gpio/Makefile +1 -0
index bdf3dde..0e2a844 100644
@@ -26,6 +26,7 @@ obj-$(CONFIG_GPIO_PL061)	+= pl061.o
 obj-$(CONFIG_GPIO_STMPE)	+= stmpe-gpio.o
 obj-$(CONFIG_GPIO_TC35892)	+= tc35892-gpio.o
 obj-$(CONFIG_GPIO_TIMBERDALE)	+= timbgpio.o
+obj-$(CONFIG_GPIO_TI_SSP)	+= ti-ssp-gpio.o
 obj-$(CONFIG_GPIO_TWL4030)	+= twl4030-gpio.o
 obj-$(CONFIG_GPIO_UCB1400)	+= ucb1400_gpio.o
 obj-$(CONFIG_GPIO_XILINX)	+= xilinx_gpio.o
drivers/gpio/ti-ssp-gpio.c new file +206 -0

206 lines not on this page · raw message

include/linux/mfd/ti_ssp.h +4 -0
index dbb4b43..10c65bb 100644
@@ -38,6 +38,10 @@ struct ti_ssp_spi_data {
 	void		(*select)(int cs);
 };
 
+struct ti_ssp_gpio_data {
+	int		start;
+};
+
 /*
  * Sequencer port IO pin configuration bits.  These do not correlate 1-1 with
  * the hardware.  The iosel field in the port data combines iosel1 and iosel2,
Signature · 1 line
1.7.1
#11 lore raw

PATCH v6 8/12 gpio: add ti-ssp gpio driver

Quoted 25 lines · Cyril Chemparathy

TI's SSP controller pins can be directly read and written to behave like a GPIO. This patch adds a GPIO driver that exposes such functionality.

---

drivers/gpio/ti-ssp-gpio.c new file +19 -0
+static int __devinit ti_ssp_gpio_probe(struct platform_device *pdev)
+{
+	const struct ti_ssp_gpio_data *pdata = pdev->dev.platform_data;
+	struct device *dev = &pdev->dev;
+	struct ti_ssp_gpio_chip *gpio;
+	int error;
+
+	if (!pdata) {
+		dev_err(dev, "platform data not found\n");
+		return -EINVAL;
+	}
+
+	gpio = kzalloc(sizeof(*gpio), GFP_KERNEL);
+	if (!gpio) {
+		dev_err(dev, "cannot allocate driver data\n");
+		return -ENOMEM;
+	}
+
+	gpio->dev = dev;

drivers/gpio/ti-ssp-gpio.c line 144

Quoted 10 lines
drivers/gpio/ti-ssp-gpio.c new file +10 -0
+	gpio->iosel = SSP_PIN_SEL(0, SSP_IN) | SSP_PIN_SEL(1, SSP_IN) |
+		      SSP_PIN_SEL(2, SSP_IN) | SSP_PIN_SEL(3, SSP_IN);
+	error = ti_ssp_set_iosel(gpio->dev, gpio->iosel);
+	if (error < 0) {
+		dev_err(dev, "gpio io setup failed (%d)\n", error);
+		goto error;
+	}
+
+	spin_lock_init(&gpio->lock);
+	platform_set_drvdata(pdev, gpio);

This looks wrong. gpio is of type ti_ssp_gpio_chip, but the ssp core functions, ssp_read, etc, use dev_to_ssp:

static inline struct ti_ssp *dev_to_ssp(struct device *dev)

{
	return dev_get_drvdata(dev->parent);
}

If I understand correctly, the ssp core can only be used to for one peripheral at a time. Currently the code will allow you to install several peripherals at once, which will lead to odd behaviour at runtime. Maybe a better approach would be to have something like this in drivers/mfd/ti-ssp.c:

struct ti_ssp {
	struct resource		*res;
	struct device		*dev;
	void __iomem		*regs;
	struct clk		*clk;
	int			irq;
	wait_queue_head_t	wqh;
	int			in_use;
};
static struct ti_ssp ti_ssp = {
	.in_use = 0,
};

static DEFINE_SPINLOCK(ti_ssp_lock);

struct ti_ssp *ti_ssp_get(void)

{
	spin_lock(&ti_ssp_lock);
	if (ti_ssp.in_use) {
		spin_unlock(&ti_ssp_lock);
		return NULL;
	}

	ti_ssp.in_use = 1;
	spin_unlock(&ti_ssp_lock);
	return &ti_ssp;
}

int ti_ssp_put(void)

{
	spin_lock(&ti_ssp_lock);
	if (!ti_ssp.in_use) {
		spin_unlock(&ti_ssp_lock);
		return -ENODEV;
	}
	
	ti_ssp.in_use = 0;	
	spin_unlock(&ti_ssp_lock);
	return 0;
}

This way, the ssp core api functions can take struct ti_ssp * as their first argument (which can still be an opaque pointer) and the code protects against multiple peripherals attempting to register the ssp core.

~Ryan

Signature · 7 lines
Bluewater Systems Ltd - ARM Technology Solution Centre

Ryan Mallon         		5 Amuri Park, 404 Barbadoes St
ryan at bluewatersys.com         	PO Box 13 889, Christchurch 8013
http://www.bluewatersys.com	New Zealand
Phone: +64 3 3779127		Freecall: Australia 1800 148 751
Fax:   +64 3 3779135			  USA 1800 261 2934
#12 lore raw

PATCH v6 8/12 gpio: add ti-ssp gpio driver

Quoted 31 lines · Ryan Mallon
Quoted 30 lines · Cyril Chemparathy

TI's SSP controller pins can be directly read and written to behave like a GPIO. ?This patch adds a GPIO driver that exposes such functionality.

---

(quoted diff) +24 -0
+static int __devinit ti_ssp_gpio_probe(struct platform_device *pdev)
+{
+ ? ? const struct ti_ssp_gpio_data *pdata = pdev->dev.platform_data;
+ ? ? struct device *dev = &pdev->dev;
+ ? ? struct ti_ssp_gpio_chip *gpio;
+ ? ? int error;
+
+ ? ? if (!pdata) {
+ ? ? ? ? ? ? dev_err(dev, "platform data not found\n");
+ ? ? ? ? ? ? return -EINVAL;
+ ? ? }
+
+ ? ? gpio = kzalloc(sizeof(*gpio), GFP_KERNEL);
+ ? ? if (!gpio) {
+ ? ? ? ? ? ? dev_err(dev, "cannot allocate driver data\n");
+ ? ? ? ? ? ? return -ENOMEM;
+ ? ? }
+
+ ? ? gpio->dev = dev;
+ ? ? gpio->iosel = SSP_PIN_SEL(0, SSP_IN) | SSP_PIN_SEL(1, SSP_IN) |
+ ? ? ? ? ? ? ? ? ? SSP_PIN_SEL(2, SSP_IN) | SSP_PIN_SEL(3, SSP_IN);
+ ? ? error = ti_ssp_set_iosel(gpio->dev, gpio->iosel);
+ ? ? if (error < 0) {
+ ? ? ? ? ? ? dev_err(dev, "gpio io setup failed (%d)\n", error);
Quoted 8 lines
Quoted 5 lines

+ ? ? ? ? ? ? goto error;
+ ? ? }
+
+ ? ? spin_lock_init(&gpio->lock);
+ ? ? platform_set_drvdata(pdev, gpio);

This looks wrong. gpio is of type ti_ssp_gpio_chip, but the ssp core functions, ssp_read, etc, use dev_to_ssp:

This sets the child device's private data pointer, not the parents. dev_to_ssp still correctly returns the parent device private data.

Quoted 8 lines

static inline struct ti_ssp *dev_to_ssp(struct device *dev) {
? ? ? ?return dev_get_drvdata(dev->parent);
}

If I understand correctly, the ssp core can only be used to for one peripheral at a time.

I believe the ssp has 2 channels; thus up to 2 child devices.

Quoted 4 lines

Currently the code will allow you to install
several peripherals at once, which will lead to odd behaviour at runtime. Maybe a better approach would be to have something like this in drivers/mfd/ti-ssp.c:

Only the ssp core itself is allowed to register the peripheral devices, and so using the parent pointer is perfectly valid. I think Cyril's approach is fine.

g.

#13 lore raw

PATCH v6 8/12 gpio: add ti-ssp gpio driver

Quoted 10 lines · Grant Likely
Quoted 4 lines · Ryan Mallon

Currently the code will allow you to install
several peripherals at once, which will lead to odd behaviour at runtime. Maybe a better approach would be to have something like this in drivers/mfd/ti-ssp.c:

Only the ssp core itself is allowed to register the peripheral devices, and so using the parent pointer is perfectly valid. I think Cyril's approach is fine.

This is very much a standard idiom for MFD children in Linux - if the children are entirely reliant on working through a parent-specific API anyway there's no issue with making the parent device be part of that API.

#14 lore raw

PATCH v6 8/12 gpio: add ti-ssp gpio driver

Quoted 8 lines · Mark Brown
Quoted 6 lines · Grant Likely
Quoted 4 lines · Ryan Mallon

Currently the code will allow you to install
several peripherals at once, which will lead to odd behaviour at runtime. Maybe a better approach would be to have something like this in drivers/mfd/ti-ssp.c:

Quoted 8 lines
Quoted 3 lines

Only the ssp core itself is allowed to register the peripheral devices, and so using the parent pointer is perfectly valid. I think Cyril's approach is fine.

This is very much a standard idiom for MFD children in Linux - if the children are entirely reliant on working through a parent-specific API anyway there's no issue with making the parent device be part of that API.

Yeah, I misunderstood how the registration worked. It is fine as is, ignore my comments :-).

~Ryan

Signature · 7 lines
Bluewater Systems Ltd - ARM Technology Solution Centre

Ryan Mallon         		5 Amuri Park, 404 Barbadoes St
ryan at bluewatersys.com         	PO Box 13 889, Christchurch 8013
http://www.bluewatersys.com	New Zealand
Phone: +64 3 3779127		Freecall: Australia 1800 148 751
Fax:   +64 3 3779135			  USA 1800 261 2934
#15 lore raw

PATCH v6 9/12 davinci: add tnetv107x evm ti-ssp gpio device

In reply to Cyril Chemparathy

This patch adds definitions to hook up one of the ti-ssp ports to the SSP GPIO driver.

---
 arch/arm/mach-davinci/board-tnetv107x-evm.c |   11 +++++++++++
 1 files changed, 11 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +11 -0
index ca23516..e3863dd 100644
@@ -39,6 +39,8 @@
 #include <mach/cp_intc.h>
 #include <mach/tnetv107x.h>
 
+#define SSP_GPIO_START		128
+
 #define EVM_MMC_WP_GPIO		21
 #define EVM_MMC_CD_GPIO		24
 #define EVM_SPI_CS_GPIO		54
@@ -238,9 +240,18 @@ static struct ti_ssp_spi_data spi_master_data = {
 		  SSP_INPUT_SEL(3),
 };
 
+static struct ti_ssp_gpio_data ssp_gpio_data = {
+	.start		= SSP_GPIO_START,
+};
+
 static struct ti_ssp_data ssp_config = {
 	.out_clock	= 250 * 1000,
 	.dev_data	= {
+		[0] = {
+			.dev_name = "ti-ssp-gpio",
+			.pdata = &ssp_gpio_data,
+			.pdata_size = sizeof(ssp_gpio_data),
+		},
 		[1] = {
 			.dev_name = "ti-ssp-spi",
 			.pdata = &spi_master_data,
Signature · 1 line
1.7.1
#16 lore raw

PATCH v6 10/12 backlight: add support for tps6116x controller

In reply to Cyril Chemparathy

TPS6116x is an EasyScale backlight controller device. This driver supports TPS6116x devices connected on a single GPIO.

---
 drivers/video/backlight/Kconfig    |    7 +
 drivers/video/backlight/Makefile   |    2 +-
 drivers/video/backlight/tps6116x.c |  298 ++++++++++++++++++++++++++++++++++++
 3 files changed, 306 insertions(+), 1 deletions(-)
 create mode 100644 drivers/video/backlight/tps6116x.c
drivers/video/backlight/Kconfig +7 -0
index e54a337..06e868e 100644
@@ -307,6 +307,13 @@ config BACKLIGHT_PCF50633
 	  If you have a backlight driven by a NXP PCF50633 MFD, say Y here to
 	  enable its driver.
 
+config BACKLIGHT_TPS6116X
+	tristate "TPS6116X LCD Backlight"
+	depends on GENERIC_GPIO
+	help
+	  This driver controls the LCD backlight level for EasyScale capable
+	  SSP connected backlight controllers.
+
 endif # BACKLIGHT_CLASS_DEVICE
 
 endif # BACKLIGHT_LCD_SUPPORT
drivers/video/backlight/Makefile +1 -1
index 44c0f81..5d407c8 100644
@@ -35,4 +35,4 @@ obj-$(CONFIG_BACKLIGHT_ADP5520)	+= adp5520_bl.o
 obj-$(CONFIG_BACKLIGHT_ADP8860)	+= adp8860_bl.o
 obj-$(CONFIG_BACKLIGHT_88PM860X) += 88pm860x_bl.o
 obj-$(CONFIG_BACKLIGHT_PCF50633)	+= pcf50633-backlight.o
-
+obj-$(CONFIG_BACKLIGHT_TPS6116X)+= tps6116x.o
drivers/video/backlight/tps6116x.c new file +298 -0

298 lines not on this page · raw message

Signature · 1 line
1.7.1
#17 lore raw

PATCH v6 11/12 davinci: add tnetv107x evm backlight device

In reply to Cyril Chemparathy

The tnetv107x evm board has a backlight device that is connected on one of the SSP ports. This patch adds the board definitions necessary to plug the backlight driver to the GPIO corresponding to this SSP pin.

---
 arch/arm/mach-davinci/board-tnetv107x-evm.c |   14 ++++++++++++++
 1 files changed, 14 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +14 -0
index e3863dd..ac62de2 100644
@@ -44,6 +44,7 @@
 #define EVM_MMC_WP_GPIO		21
 #define EVM_MMC_CD_GPIO		24
 #define EVM_SPI_CS_GPIO		54
+#define EVM_BACKLIGHT_GPIO	(SSP_GPIO_START + 2)
 
 static int initialize_gpio(int gpio, char *desc)
 {
@@ -353,6 +354,12 @@ static struct spi_board_info spi_info[] __initconst = {
 	},
 };
 
+static struct platform_device backlight_device = {
+	.name		= "tps6116x",
+	.id		= -1,
+	.dev.platform_data = (void *)EVM_BACKLIGHT_GPIO,
+};
+
 static __init void tnetv107x_evm_board_init(void)
 {
 	davinci_cfg_reg_list(sdio1_pins);
@@ -364,6 +371,13 @@ static __init void tnetv107x_evm_board_init(void)
 	spi_register_board_info(spi_info, ARRAY_SIZE(spi_info));
 }
 
+static int __init tnetv107x_evm_late_init(void)
+{
+	platform_device_register(&backlight_device);
+	return 0;
+}
+late_initcall(tnetv107x_evm_late_init);
+
 #ifdef CONFIG_SERIAL_8250_CONSOLE
 static int __init tnetv107x_evm_console_init(void)
 {
Signature · 1 line
1.7.1
#18 lore raw

PATCH v6 11/12 davinci: add tnetv107x evm backlight device

Hello.

Quoted 14 lines · Cyril Chemparathy

The tnetv107x evm board has a backlight device that is connected on one of the SSP ports. This patch adds the board definitions necessary to plug the backlight driver to the GPIO corresponding to this SSP pin.

---
 arch/arm/mach-davinci/board-tnetv107x-evm.c |   14 ++++++++++++++
 1 files changed, 14 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +0 -0
index e3863dd..ac62de2 100644

arch/arm/mach-davinci/board-tnetv107x-evm.c line 47

Quoted 4 lines
arch/arm/mach-davinci/board-tnetv107x-evm.c +1 -0
@@ -44,6 +44,7 @@
 #define EVM_MMC_WP_GPIO		21
 #define EVM_MMC_CD_GPIO		24
 #define EVM_SPI_CS_GPIO		54
+#define EVM_BACKLIGHT_GPIO	(SSP_GPIO_START + 2)

Why it's not aligned with others?

WBR, Sergei

#19 lore raw

PATCH v6 11/12 davinci: add tnetv107x evm backlight device

Quoted 13 lines · Sergei Shtylyov

Hello.

Quoted 8 lines · Cyril Chemparathy

The tnetv107x evm board has a backlight device that is connected on one of the SSP ports. This patch adds the board definitions necessary to plug the backlight driver to the GPIO corresponding to this SSP pin.

---
 arch/arm/mach-davinci/board-tnetv107x-evm.c |   14 ++++++++++++++
 1 files changed, 14 insertions(+), 0 deletions(-)
Quoted 11 lines

arch/arm/mach-davinci/board-tnetv107x-evm.c line 47

Quoted 9 lines
arch/arm/mach-davinci/board-tnetv107x-evm.c +1 -0
index e3863dd..ac62de2 100644
@@ -44,6 +44,7 @@
 #define EVM_MMC_WP_GPIO		21
 #define EVM_MMC_CD_GPIO		24
 #define EVM_SPI_CS_GPIO		54
+#define EVM_BACKLIGHT_GPIO	(SSP_GPIO_START + 2)

Why it's not aligned with others?

It actually is aligned if you remove the leading space/+.

Regards
Cyril.

#20 lore raw

PATCH v6 11/12 davinci: add tnetv107x evm backlight device

Hello.

Quoted 19 lines · Cyril Chemparathy
Quoted 10 lines
Quoted 10 lines

The tnetv107x evm board has a backlight device that is connected on one of the SSP ports. This patch adds the board definitions necessary to plug the backlight driver to the GPIO corresponding to this SSP pin.

---
 arch/arm/mach-davinci/board-tnetv107x-evm.c |   14 ++++++++++++++
 1 files changed, 14 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +0 -1
index e3863dd..ac62de2 100644
--- a/arch/arm/mach-davinci/board-tnetv107x-evm.c
Quoted 8 lines

arch/arm/mach-davinci/board-tnetv107x-evm.c line 47

Quoted 6 lines

+++ b/arch/arm/mach-davinci/board-tnetv107x-evm.c

arch/arm/mach-davinci/board-tnetv107x-evm.c +1 -0
@@ -44,6 +44,7 @@
 #define EVM_MMC_WP_GPIO		21
 #define EVM_MMC_CD_GPIO		24
 #define EVM_SPI_CS_GPIO		54
+#define EVM_BACKLIGHT_GPIO	(SSP_GPIO_START + 2)

Why it's not aligned with others?

Quoted 1 line

It actually is aligned if you remove the leading space/+.

Heh, realized that after sending. :-)
That's why I use spaces instead of one-space tab. Unfortunately,
scripts/checkpatch.pl does not like it now... :-/

Quoted 2 lines

Regards
Cyril.

WBR, Sergei

#21 lore raw

PATCH v6 12/12 davinci: add tnetv107x evm i2c eeprom device

In reply to Cyril Chemparathy

The tnetv107x evm board has an I2C device connected on one of the SSP ports. This patch adds board definitions for a GPIO based I2C master, as well as definitions for the eeprom device on these boards.

---
 arch/arm/mach-davinci/board-tnetv107x-evm.c |   30 +++++++++++++++++++++++++++
 1 files changed, 30 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +30 -0
index ac62de2..869af15 100644
@@ -29,6 +29,9 @@
 #include <linux/regulator/machine.h>
 #include <linux/regulator/consumer.h>
 #include <linux/regulator/driver.h>
+#include <linux/i2c.h>
+#include <linux/i2c/at24.h>
+#include <linux/i2c-gpio.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach-types.h>
@@ -44,6 +47,8 @@
 #define EVM_MMC_WP_GPIO		21
 #define EVM_MMC_CD_GPIO		24
 #define EVM_SPI_CS_GPIO		54
+#define EVM_I2C_SDA_GPIO	(SSP_GPIO_START + 0)
+#define EVM_I2C_SCL_GPIO	(SSP_GPIO_START + 1)
 #define EVM_BACKLIGHT_GPIO	(SSP_GPIO_START + 2)
 
 static int initialize_gpio(int gpio, char *desc)
@@ -360,6 +365,29 @@ static struct platform_device backlight_device = {
 	.dev.platform_data = (void *)EVM_BACKLIGHT_GPIO,
 };
 
+struct i2c_gpio_platform_data i2c_data = {
+	.sda_pin	= EVM_I2C_SDA_GPIO,
+	.scl_pin	= EVM_I2C_SCL_GPIO,
+};
+
+static struct platform_device i2c_device = {
+	.name		= "i2c-gpio",
+	.id		= 0,
+	.dev.platform_data = &i2c_data,
+};
+
+static struct at24_platform_data at24_config = {
+	.byte_len	= SZ_16K / 8,
+	.page_size	= 16,
+};
+
+static struct i2c_board_info i2c_info[] __initconst =  {
+	{
+		I2C_BOARD_INFO("24c16", 0x50),
+		.platform_data	= &at24_config,
+	},
+};
+
 static __init void tnetv107x_evm_board_init(void)
 {
 	davinci_cfg_reg_list(sdio1_pins);
@@ -369,11 +397,13 @@ static __init void tnetv107x_evm_board_init(void)
 	tnetv107x_devices_init(&evm_device_info);
 
 	spi_register_board_info(spi_info, ARRAY_SIZE(spi_info));
+	i2c_register_board_info(0, i2c_info, ARRAY_SIZE(i2c_info));
 }
 
 static int __init tnetv107x_evm_late_init(void)
 {
 	platform_device_register(&backlight_device);
+	platform_device_register(&i2c_device);
 	return 0;
 }
 late_initcall(tnetv107x_evm_late_init);
Signature · 1 line
1.7.1