S5PC110: add MIPI-DSI driver.
PATCH 4/4 S5PC110: add MIPI-DSI driver.
driver features:
. Maximum resolution ranges up to XGA (1024x760)
. CSIS0 supports 1,2,3 or 4 data lanes
. CSIS1 supports 1 or 2 data lanes
. support pixel format : 16bpp, 18bpp packed,
18bpp loosely packed (3 byte format), and 24bpp
(now would use 24bpp)
. support RGB interface for video image from display controller . support I80 interface for command mode image input from display controller . support PMS control interface for PLL to configure byte clock frequency . support Prescaler to generate escape clock from byte clock
--- arch/arm/plat-s5p/include/plat/dsim.h | 470 +++++++++++++++++++ arch/arm/plat-s5p/include/plat/mipi_ddi.h | 94 ++++ arch/arm/plat-s5p/include/plat/regs-dsim.h | 281 +++++++++++ drivers/video/Kconfig | 7 + drivers/video/Makefile | 2 + drivers/video/s5p-dsim.c | 463 +++++++++++++++++++ drivers/video/s5p_dsim_common.c | 691 ++++++++++++++++++++++++++++ drivers/video/s5p_dsim_common.h | 35 ++ drivers/video/s5p_dsim_lowlevel.c | 569 +++++++++++++++++++++++ drivers/video/s5p_dsim_lowlevel.h | 101 ++++ 10 files changed, 2713 insertions(+), 0 deletions(-) create mode 100644 arch/arm/plat-s5p/include/plat/dsim.h create mode 100644 arch/arm/plat-s5p/include/plat/mipi_ddi.h create mode 100644 arch/arm/plat-s5p/include/plat/regs-dsim.h create mode 100644 drivers/video/s5p-dsim.c create mode 100644 drivers/video/s5p_dsim_common.c create mode 100644 drivers/video/s5p_dsim_common.h create mode 100644 drivers/video/s5p_dsim_lowlevel.c create mode 100644 drivers/video/s5p_dsim_lowlevel.h
arch/arm/plat-s5p/include/plat/dsim.h new file +470 -0
@@ -0,0 +1,470 @@ +/* linux/arm/arch/plat-s5p/include/plat/dsim.h +* +* Platform data header for Samsung MIPI-DSIM. +* +* Copyright (c) 2009 Samsung Electronics +* InKi Dae <[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +*/ + +#ifndef _DSIM_H +#define _DSIM_H + +#include <linux/device.h> + +/* h/w configuration */ +#define MIPI_FIN 24000000 + +#define DSIM_TRUE 1 +#define DSIM_FALSE 0 + +#define DSIM_HEADER_FIFO_SZ 16 + +enum dsim_interface_type { +DSIM_COMMAND =0 , +DSIM_VIDEO =1 , +}; + +enum dsim_state { +DSIM_STATE_RESET =0 , +DSIM_STATE_INIT =1 , +DSIM_STATE_STOP =2 , +DSIM_STATE_HSCLKEN =3 , +DSIM_STATE_ULPS =4 , +}; + +enum dsim_virtual_ch_no { +DSIM_VIRTUAL_CH_0 =0 , +DSIM_VIRTUAL_CH_1 =1 , +DSIM_VIRTUAL_CH_2 =2 , +DSIM_VIRTUAL_CH_3 =3 , +}; + +enum dsim_video_mode_type { +DSIM_NON_BURST_SYNC_EVENT =0 , +DSIM_NON_BURST_SYNC_PULSE =2 , +DSIM_BURST =3 , +DSIM_NON_VIDEO_MODE =4 , +}; + +enum dsim_fifo_state { +DSIM_RX_DATA_FULL = (1 <<25 ), +DSIM_RX_DATA_EMPTY = (1 <<24 ), +SFR_HEADER_FULL = (1 <<23 ), +SFR_HEADER_EMPTY = (1 <<22 ), +SFR_PAYLOAD_FULL = (1 <<21 ), +SFR_PAYLOAD_EMPTY = (1 <<20 ), +I80_HEADER_FULL = (1 <<19 ), +I80_HEADER_EMPTY = (1 <<18 ), +I80_PALOAD_FULL = (1 <<17 ), +I80_PALOAD_EMPTY = (1 <<16 ), +SUB_DISP_HEADER_FULL = (1 <<15 ), +SUB_DISP_HEADER_EMPTY = (1 <<14 ), +SUB_DISP_PAYLOAD_FULL = (1 <<13 ), +SUB_DISP_PAYLOAD_EMPTY = (1 <<12 ), +MAIN_DISP_HEADER_FULL = (1 <<11 ), +MAIN_DISP_HEADER_EMPTY = (1 <<10 ), +MAIN_DISP_PAYLOAD_FULL = (1 <<9 ), +MAIN_DISP_PAYLOAD_EMPTY = (1 <<8 ), +}; + +enum dsim_no_of_data_lane { +DSIM_DATA_LANE_1 =0 , +DSIM_DATA_LANE_2 =1 , +DSIM_DATA_LANE_3 =2 , +DSIM_DATA_LANE_4 =3 , +}; + +enum dsim_byte_clk_src { +DSIM_PLL_OUT_DIV8 =0 , +DSIM_EXT_CLK_DIV8 =1 , +DSIM_EXT_CLK_BYPASS =2 , +}; + +enum dsim_lane { +DSIM_LANE_DATA0 = (1 <<0 ), +DSIM_LANE_DATA1 = (1 <<1 ), +DSIM_LANE_DATA2 = (1 <<2 ), +DSIM_LANE_DATA3 = (1 <<3 ), +DSIM_LANE_DATA_ALL =0xf , +DSIM_LANE_CLOCK = (1 <<4 ), +DSIM_LANE_ALL =DSIM_LANE_CLOCK |DSIM_LANE_DATA_ALL , +}; + +enum dsim_pixel_format { +DSIM_CMD_3BPP =0 , +DSIM_CMD_8BPP =1 , +DSIM_CMD_12BPP =2 , +DSIM_CMD_16BPP =3 , +DSIM_VID_16BPP_565 =4 , +DSIM_VID_18BPP_666PACKED =5 , +DSIM_18BPP_666LOOSELYPACKED =6 , +DSIM_24BPP_888 =7 , +}; + +enum dsim_lane_state { +DSIM_LANE_STATE_HS_READY , +DSIM_LANE_STATE_ULPS , +DSIM_LANE_STATE_STOP , +DSIM_LANE_STATE_LPDT , +}; + +enum dsim_transfer { +DSIM_TRANSFER_NEITHER =0 , +DSIM_TRANSFER_BYCPU = (1 <<7 ), +DSIM_TRANSFER_BYLCDC = (1 <<6 ), +DSIM_TRANSFER_BOTH = (0x3 <<6 ) +}; + +enum dsim_lane_change { +DSIM_NO_CHANGE =0 , +DSIM_DATA_LANE_CHANGE =1 , +DSIM_CLOCK_NALE_CHANGE =2 , +DSIM_ALL_LANE_CHANGE =3 , +}; + +enum dsim_int_src { +DSIM_ALL_OF_INTR =0xffffffff , +DSIM_PLL_STABLE = (1 <<31 ), +}; + +/** +* struct dsim_config - interface for configuring mipi-dsi controller. +* +* @auto_flush: enable or disable Auto flush of MD FIFO using VSYNC pulse. +* @eot_disable: enable or disable EoT packet in HS mode. +* @auto_vertical_cnt: specifies auto vertical count mode. +* in Video mode, the vertical line transition uses line counter +* configured by VSA, VBP, and Vertical resolution. +* If this bit is set to '1', the line counter does not use VSA and VBP +* registers.(in command mode, this variable is ignored) +* @hse: set horizontal sync event mode. +* In VSYNC pulse and Vporch area, MIPI DSI master transfers only HSYNC +* start packet to MIPI DSI slave at MIPI DSI spec1.1r02. +* this bit transfers HSYNC end packet in VSYNC pulse and Vporch area +* (in mommand mode, this variable is ignored) +* @hfp: specifies HFP disable mode. +* if this variable is set, DSI master ignores HFP area in VIDEO mode. +* (in command mode, this variable is ignored) +* @hbp: specifies HBP disable mode. +* if this variable is set, DSI master ignores HBP area in VIDEO mode. +* (in command mode, this variable is ignored) +* @hsa: specifies HSA disable mode. +* if this variable is set, DSI master ignores HSA area in VIDEO mode. +* (in command mode, this variable is ignored) +* @e_no_data_lane: specifies data lane count to be used by Master. +* @e_byte_clk: select byte clock source. (it must be DSIM_PLL_OUT_DIV8) +* DSIM_EXT_CLK_DIV8 and DSIM_EXT_CLK_BYPASSS are not supported. +* @pll_stable_time: specifies the PLL Timer for stability of the ganerated +* clock(System clock cycle base) +* if the timer value goes to 0x00000000, the clock stable bit of status +* and interrupt register is set. +* @esc_clk: specifies escape clock frequency for getting the escape clock +* prescaler value. +* @stop_holding_cnt: specifies the interval value between transmitting +* read packet(or write "set_tear_on" command) and BTA request. +* after transmitting read packet or write "set_tear_on" command, +* BTA requests to D-PHY automatically. this counter value specifies +* the interval between them. +* @bta_timeout: specifies the timer for BTA. +* this register specifies time out from BTA request to change +* the direction with respect to Tx escape clock. +* @rx_timeout: specifies the timer for LP Rx mode timeout. +* this register specifies time out on how long RxValid deasserts, +* after RxLpdt asserts with respect to Tx escape clock. +* - RxValid specifies Rx data valid indicator. +* - RxLpdt specifies an indicator that D-PHY is under RxLpdt mode. +* - RxValid and RxLpdt specifies signal from D-PHY. +* @e_lane_swap: swaps Dp/Dn channel of Clock lane or Data lane. +* if this bit is set, Dp and Dn channel would be swapped each other. +*/ +struct dsim_config { +unsigned char auto_flush; +unsigned char eot_disable; + +unsigned char auto_vertical_cnt; +unsigned char hse; +unsigned char hfp; +unsigned char hbp; +unsigned char hsa; + +enum dsim_no_of_data_lane e_no_data_lane; +enum dsim_byte_clk_src e_byte_clk; + +/* +* =========================================== +* | P | M | S | MHz | +* ------------------------------------------- +* | 3 | 100 | 3 | 100 | +* | 3 | 100 | 2 | 200 | +* | 3 | 63 | 1 | 252 | +* | 4 | 100 | 1 | 300 | +* | 4 | 110 | 1 | 330 | +* | 12 | 350 | 1 | 350 | +* | 3 | 100 | 1 | 400 | +* | 4 | 150 | 1 | 450 | +* | 3 | 118 | 1 | 472 | +* | 12 | 250 | 0 | 500 | +* | 4 | 100 | 0 | 600 | +* | 3 | 81 | 0 | 648 | +* | 3 | 88 | 0 | 704 | +* | 3 | 90 | 0 | 720 | +* | 3 | 100 | 0 | 800 | +* | 12 | 425 | 0 | 850 | +* | 4 | 150 | 0 | 900 | +* | 12 | 475 | 0 | 950 | +* | 6 | 250 | 0 | 1000 | +* ------------------------------------------- +*/ +unsigned char p; +unsigned short m; +unsigned char s; + +unsigned int pll_stable_time; +unsigned long esc_clk; + +unsigned short stop_holding_cnt; +unsigned char bta_timeout; +unsigned short rx_timeout; +enum dsim_video_mode_type e_lane_swap; +}; + +/** +* struct dsim_lcd_config - interface for configuring mipi-dsi based lcd panel. +* +* @e_interface: specifies interface to be used.(CPU or RGB interface) +* @parameter[0]: specifies virtual channel number +* that main or sub diaplsy uses. +* @parameter[1]: specifies pixel stream format for main or sub display. +* @parameter[2]: selects Burst mode in Video mode. +* in Non-burst mode, RGB data area is filled with RGB data and NULL +* packets, according to input bandwidth of RGB interface. +* In Burst mode, RGB data area is filled with RGB data only. +* @lcd_panel_info: pointer for lcd panel specific structure. +* this structure specifies width, height, timing and polarity and so on. +* @mipi_ddi_pd: pointer for lcd panel platform data. +*/ +struct dsim_lcd_config { +enum dsim_interface_type e_interface; +unsigned int parameter[3 ]; + +void *lcd_panel_info; +void *mipi_ddi_pd; +}; + +struct dsim_global ; +struct fb_info ; +struct regulator ; + +/** +* struct s5p_platform_dsim - interface to platform data for mipi-dsi driver. +* +* @clk_name: specifies clock name for mipi-dsi. +* @lcd_panel_name: specifies lcd panel name registered to mipi-dsi driver. +* lcd panel driver searched would be actived. +* @mipi_1_1v_name: specifies mipi 1.1v regulator name. +* @mipi_1_8v_name: specifies mipi 1.8v regulator name. +* @platfrom_rev: specifies platform revision number. +* revision number should become 1. +* @dsim_config: pointer of structure for configuring mipi-dsi controller. +* @dsim_lcd_info: pointer to structure for configuring +* mipi-dsi based lcd panel. +* @mipi_power: callback pointer for enabling or disabling mipi power. +* @part_reset: callback pointer for reseting mipi phy. +* @init_d_phy: callback pointer for enabing d_phy of dsi master. +* @get_fb_frame_done: callback pointer for getting frame done status of the +* display controller(FIMD). +* @trigger: callback pointer for triggering display controller(FIMD) +* in case of CPU mode. +* @delay_for_stabilization: specifies stable time. +* this delay needs when writing data on SFR +* after mipi mode became LP mode. +*/ +struct s5p_platform_dsim { +char *clk_name; +char *mipi_1_1v_name; +char *mipi_1_8v_name; +char lcd_panel_name[64 ]; +unsigned int platform_rev; + +struct dsim_config *dsim_info; +struct dsim_lcd_config *dsim_lcd_info; + +unsigned int delay_for_stabilization; + +int (*mipi_power) (struct dsim_global *dsim, +struct regulator *p_mipi_1_1v, +struct regulator *p_mipi_1_8v,unsigned int enable); +int (*part_reset) (struct dsim_global *dsim); +int (*init_d_phy) (struct dsim_global *dsim); +int (*get_fb_frame_done) (struct fb_info *info); +void (*trigger) (struct fb_info *info); +}; + +/** +* struct dsim_global - global interface for mipi-dsi driver. +* +* @dev: driver model representation of the device. +* @clock: pointer to MIPI-DSI clock of clock framework. +* @irq: interrupt number to MIPI-DSI controller. +* @reg_base: base address to memory mapped SRF of MIPI-DSI controller. +* (virtual address) +* @r_mipi_1_1v: pointer to regulator for MIPI 1.1v power. +* @r_mipi_1_8v: pointer to regulator for MIPI 1.8v power. +* @pd: pointer to MIPI-DSI driver platform data. +* @dsim_lcd_info: pointer to structure for configuring +* mipi-dsi based lcd panel. +* @lcd_panel_info: pointer for lcd panel specific structure. +* this structure specifies width, height, timing and polarity and so on. +* @mipi_ddi_pd: pointer for lcd panel platform data. +* @mipi_drv: pointer to driver structure for mipi-dsi based lcd panel. +* @s3cfb_notif: kernel notifier structure to be registered +* by device specific framebuffer driver. +* this notifier could be used by fb_blank of device specifiec +* framebuffer driver. +* @state: specifies status of MIPI-DSI controller. +* the status could be RESET, INIT, STOP, HSCLKEN and ULPS. +* @data_lane: specifiec enabled data lane number. +* this variable would be set by driver according to e_no_data_lane +* automatically. +* @e_clk_src: select byte clock source. +* this variable would be set by driver according to e_byte_clock +* automatically. +* @hs_clk: HS clock rate. +* this variable would be set by driver automatically. +* @byte_clk: Byte clock rate. +* this variable would be set by driver automatically. +* @escape_clk: ESCAPE clock rate. +* this variable would be set by driver automatically. +* @freq_band: indicates Bitclk frequency band for D-PHY global timing. +* Serial Clock(=ByteClk X 8) FreqBand[3:0] +* ~ 99.99 MHz 0000 +* 100 ~ 119.99 MHz 0001 +* 120 ~ 159.99 MHz 0010 +* 160 ~ 199.99 MHz 0011 +* 200 ~ 239.99 MHz 0100 +* 140 ~ 319.99 MHz 0101 +* 320 ~ 389.99 MHz 0110 +* 390 ~ 449.99 MHz 0111 +* 450 ~ 509.99 MHz 1000 +* 510 ~ 559.99 MHz 1001 +* 560 ~ 639.99 MHz 1010 +* 640 ~ 689.99 MHz 1011 +* 690 ~ 769.99 MHz 1100 +* 770 ~ 869.99 MHz 1101 +* 870 ~ 949.99 MHz 1110 +* 950 ~ 1000 MHz 1111 +* this variable would be calculated by driver automatically. +* +* @header_fifo_index: specifies header fifo index. +* this variable is not used yet. +*/ +struct dsim_global { +struct device *dev; +struct clk *clock; +unsigned int irq; +void __iomem *reg_base; + +struct regulator *r_mipi_1_1v; +struct regulator *r_mipi_1_8v; + +struct s5p_platform_dsim *pd; +struct dsim_config *dsim_info; +struct dsim_lcd_config *dsim_lcd_info; +struct fb_videomode *lcd_panel_info; +struct mipi_ddi_platform_data *mipi_ddi_pd; +struct mipi_lcd_driver *mipi_drv; +struct notifier_block s3cfb_notif; + +unsigned char state; +unsigned int data_lane; +enum dsim_byte_clk_src e_clk_src; +unsigned long hs_clk; +unsigned long byte_clk; +unsigned long escape_clk; +unsigned char freq_band; + +char header_fifo_index[DSIM_HEADER_FIFO_SZ ]; +}; + +/** +* driver structure for mipi-dsi based lcd panel. +* +* this structure should be registered by lcd panel driver. +* mipi-dsi driver seeks lcd panel registered through name field +* and calls these callback functions in appropriate time. +*/ +struct mipi_lcd_driver { +s8 *name; + +s32 (*init)(struct device *dev); +void (*display_on)(struct device *dev); +s32 (*set_link)(struct mipi_ddi_platform_data *pd); +s32 (*probe)(struct device *dev); +s32 (*remove)(struct device *dev); +void (*shutdown)(struct device *dev); +s32 (*suspend)(struct device *dev); +s32 (*resume)(struct device *dev); +}; + +/** +* register mipi_lcd_driver object defined by lcd panel driver +* to mipi-dsi driver. +*/ +extern int s5p_dsim_register_lcd_driver (struct mipi_lcd_driver *lcd_drv); + +/** +* reset MIPI PHY through MIPI PHY CONTROL REGISTER +*/ +extern int s5p_dsim_part_reset (struct dsim_global *dsim); + +/** +* enable MIPI D-PHY and DSI Master block. +*/ +extern int s5p_dsim_init_d_phy (struct dsim_global *dsim); + +struct regulator ; + +/** +* enable regulators to MIPI-DSI power. +*/ +extern int s5p_dsim_mipi_power (struct dsim_global *dsim, +struct regulator *p_mipi_1_1v,struct regulator *p_mipi_1_8v, +unsigned int enable); + +/** +* send commands to mipi based lcd panel. +* +* @dsim_data: point to struct dsim_global. +* @data_id: MIPI-DSI Command ID. +* @data0: address to command array. +* @data1: size of command array. +*/ +extern int s5p_dsim_wr_data (void *dsim_data,unsigned int data_id, +unsigned int data0,unsigned int data1); + +/** +* get framedone status of mipi-dsi controller. +* +* @dsim_data: point to struct dsim_global. +*/ +extern int s5p_dsim_get_frame_done_status (void *dsim_data); + +/** +* clear framedone interrupt of mipi-dsi controller. +* +* @dsim_data: point to struct dsim_global. +*/ +extern int s5p_dsim_clear_frame_done (void *dsim_data); + +/** +* wrapper function for changing transfer mode. +* +* @mode: it could be 0(LP MODE) or 1(HS MODE). +*/ +extern int s5p_dsim_change_transfer_mode (unsigned int mode); + +#endif /* _DSIM_H */
arch/arm/plat-s5p/include/plat/mipi_ddi.h new file +94 -0
94 lines not on this page · raw message
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +281 -0
281 lines not on this page · raw message
drivers/video/Kconfig +7 -0
@@ -1996,6 +1996,13 @@ config FB_S3C2410_DEBUG Turn on debugging messages. Note that you can set/unset at run time through sysfs +config S5P_MIPI_DSI + tristate "Samsung SoC MIPI-DSI support." + depends on FB_S3C && ARCH_S5PV210 + default n + help + This enables support for MIPI-DSI device for samsung SoC S5PV210. + config FB_NUC900 bool "NUC900 LCD framebuffer support" depends on FB && ARCH_W90X900
drivers/video/Makefile +2 -0
@@ -115,6 +115,8 @@ obj-$(CONFIG_FB_SH7760) += sh7760fb.o obj-$(CONFIG_FB_IMX) += imxfb.o obj-$(CONFIG_FB_S3C) += s3c-fb.o obj-$(CONFIG_FB_S3C2410) += s3c2410fb.o +obj-$(CONFIG_S5P_MIPI_DSI) += s5p-dsim.o s5p_dsim_common.o \ + s5p_dsim_lowlevel.o obj-$(CONFIG_FB_FSL_DIU) += fsl-diu-fb.o obj-$(CONFIG_FB_COBALT) += cobalt_lcdfb.o obj-$(CONFIG_FB_PNX4008_DUM) += pnx4008/
drivers/video/s5p-dsim.c new file +463 -0
463 lines not on this page · raw message
drivers/video/s5p_dsim_common.c new file +691 -0
691 lines not on this page · raw message
drivers/video/s5p_dsim_common.h new file +35 -0
@@ -0,0 +1,35 @@ +/* linux/drivers/video/s5p_dsim_common.h +* +* Header file for Samsung MIPI-DSI common driver. +* +* Copyright (c) 2009 Samsung Electronics +* InKi Dae <[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +*/ + +#ifndef _S5P_DSIM_COMMON_H +#define _S5P_DSIM_COMMON_H + +int s5p_dsim_init_header_fifo (struct dsim_global *dsim); +int s5p_dsim_pll_on (struct dsim_global *dsim,unsigned int enable); +unsigned long s5p_dsim_change_pll (struct dsim_global *dsim, +unsigned int pre_divider,unsigned int main_divider, +unsigned int scaler); +int s5p_dsim_set_clock (struct dsim_global *dsim, +unsigned int byte_clk_sel,unsigned int enable); +int s5p_dsim_init_dsim (struct dsim_global *dsim); +int s5p_dsim_set_display_mode (struct dsim_global *dsim, +struct dsim_lcd_config *main_lcd,struct dsim_lcd_config *sub_lcd); +int s5p_dsim_init_link (struct dsim_global *dsim); +int s5p_dsim_set_hs_enable (struct dsim_global *dsim); +int s5p_dsim_set_data_transfer_mode (struct dsim_global *dsim, +unsigned int data_path,unsigned int hs_enable); +int s5p_dsim_enable_frame_done_int (struct dsim_global *dsim, +unsigned int enable); + +extern struct fb_info *registered_fb[FB_MAX ]__read_mostly ; + +#endif /* _S5P_DSIM_COMMON_H */
drivers/video/s5p_dsim_lowlevel.c new file +569 -0
569 lines not on this page · raw message
drivers/video/s5p_dsim_lowlevel.h new file +101 -0
101 lines not on this page · raw message
Signature · 1 line
1.5.4.3
PATCH 4/4 S5PC110: add MIPI-DSI driver.
Hello,
Quoted 75 lines · Inki Dae
driver features:
. Maximum resolution ranges up to XGA (1024x760)
. CSIS0 supports 1,2,3 or 4 data lanes
. CSIS1 supports 1 or 2 data lanes
. support pixel format : 16bpp, 18bpp packed,
18bpp loosely packed (3 byte format), and 24bpp
(now would use 24bpp)
. support RGB interface for video image from display controller . support I80 interface for command mode image input from display controller . support PMS control interface for PLL to configure byte clock frequency . support Prescaler to generate escape clock from byte clockSigned-off-by Inki Dae<[email protected]>Signed-off-by Kyungmin Park<[email protected]>--- arch/arm/plat-s5p/include/plat/dsim.h | 470 +++++++++++++++++++ arch/arm/plat-s5p/include/plat/mipi_ddi.h | 94 ++++ arch/arm/plat-s5p/include/plat/regs-dsim.h | 281 +++++++++++ drivers/video/Kconfig | 7 + drivers/video/Makefile | 2 + drivers/video/s5p-dsim.c | 463 +++++++++++++++++++ drivers/video/s5p_dsim_common.c | 691 ++++++++++++++++++++++++++++ drivers/video/s5p_dsim_common.h | 35 ++ drivers/video/s5p_dsim_lowlevel.c | 569 +++++++++++++++++++++++ drivers/video/s5p_dsim_lowlevel.h | 101 ++++ 10 files changed, 2713 insertions(+), 0 deletions(-)create mode 100644
arch/arm/plat-s5p/include/plat/dsim.hcreate mode 100644arch/arm/plat-s5p/include/plat/mipi_ddi.hcreate mode 100644arch/arm/plat-s5p/include/plat/regs-dsim.hcreate mode 100644drivers/video/s5p-dsim.c
create mode 100644drivers/video/s5p_dsim_common.ccreate mode 100644drivers/video/s5p_dsim_common.hcreate mode 100644drivers/video/s5p_dsim_lowlevel.ccreate mode 100644drivers/video/s5p_dsim_lowlevel.harch/arm/plat-s5p/include/plat/dsim.h new file +34
-0@@ -0,0 +1,470 @@ +/* linux/arm/arch/plat-s5p/include/plat/dsim.h +* +* Platform data header for Samsung MIPI-DSIM. +* +* Copyright (c) 2009 Samsung Electronics +* InKi Dae<[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +*/ + +#ifndef _DSIM_H +#define _DSIM_H + +#include <linux/device.h> + +/* h/w configuration */ +#define MIPI_FIN 24000000 + +#define DSIM_TRUE 1 +#define DSIM_FALSE 0 + +#define DSIM_HEADER_FIFO_SZ 16 + +enum dsim_interface_type { +DSIM_COMMAND =0 , +DSIM_VIDEO =1 , +}; + +enum dsim_state { +DSIM_STATE_RESET =0 , +DSIM_STATE_INIT =1 , + DSIM_STATE_STOP = 2,
arch/arm/plat-s5p/include/plat/dsim.h line 44
Quoted 10 lines
arch/arm/plat-s5p/include/plat/dsim.h new file +10
-0+DSIM_STATE_HSCLKEN =3 , + DSIM_STATE_ULPS = 4, +}; + +enum dsim_virtual_ch_no { +DSIM_VIRTUAL_CH_0 =0 , +DSIM_VIRTUAL_CH_1 =1 , +DSIM_VIRTUAL_CH_2 =2 , +DSIM_VIRTUAL_CH_3 =3 , +};
The enum type suggest the meaning so what is the point of redefining numbers?
Quoted 89 lines
arch/arm/plat-s5p/include/plat/dsim.h new file +89
-0+ +enum dsim_video_mode_type { +DSIM_NON_BURST_SYNC_EVENT =0 , +DSIM_NON_BURST_SYNC_PULSE =2 , +DSIM_BURST =3 , +DSIM_NON_VIDEO_MODE =4 , +}; + +enum dsim_fifo_state { +DSIM_RX_DATA_FULL = (1 <<25 ), +DSIM_RX_DATA_EMPTY = (1 <<24 ), +SFR_HEADER_FULL = (1 <<23 ), +SFR_HEADER_EMPTY = (1 <<22 ), +SFR_PAYLOAD_FULL = (1 <<21 ), +SFR_PAYLOAD_EMPTY = (1 <<20 ), +I80_HEADER_FULL = (1 <<19 ), +I80_HEADER_EMPTY = (1 <<18 ), +I80_PALOAD_FULL = (1 <<17 ), +I80_PALOAD_EMPTY = (1 <<16 ), +SUB_DISP_HEADER_FULL = (1 <<15 ), +SUB_DISP_HEADER_EMPTY = (1 <<14 ), +SUB_DISP_PAYLOAD_FULL = (1 <<13 ), +SUB_DISP_PAYLOAD_EMPTY = (1 <<12 ), +MAIN_DISP_HEADER_FULL = (1 <<11 ), +MAIN_DISP_HEADER_EMPTY = (1 <<10 ), +MAIN_DISP_PAYLOAD_FULL = (1 <<9 ), +MAIN_DISP_PAYLOAD_EMPTY = (1 <<8 ), +}; + +enum dsim_no_of_data_lane { +DSIM_DATA_LANE_1 =0 , +DSIM_DATA_LANE_2 =1 , +DSIM_DATA_LANE_3 =2 , +DSIM_DATA_LANE_4 =3 , +}; + +enum dsim_byte_clk_src { +DSIM_PLL_OUT_DIV8 =0 , +DSIM_EXT_CLK_DIV8 =1 , +DSIM_EXT_CLK_BYPASS =2 , +}; + +enum dsim_lane { +DSIM_LANE_DATA0 = (1 <<0 ), +DSIM_LANE_DATA1 = (1 <<1 ), +DSIM_LANE_DATA2 = (1 <<2 ), +DSIM_LANE_DATA3 = (1 <<3 ), +DSIM_LANE_DATA_ALL =0xf , +DSIM_LANE_CLOCK = (1 <<4 ), +DSIM_LANE_ALL =DSIM_LANE_CLOCK |DSIM_LANE_DATA_ALL , +}; + +enum dsim_pixel_format { +DSIM_CMD_3BPP =0 , +DSIM_CMD_8BPP =1 , +DSIM_CMD_12BPP =2 , +DSIM_CMD_16BPP =3 , +DSIM_VID_16BPP_565 =4 , +DSIM_VID_18BPP_666PACKED =5 , +DSIM_18BPP_666LOOSELYPACKED =6 , +DSIM_24BPP_888 =7 , +}; + +enum dsim_lane_state { +DSIM_LANE_STATE_HS_READY , +DSIM_LANE_STATE_ULPS , +DSIM_LANE_STATE_STOP , +DSIM_LANE_STATE_LPDT , +}; + +enum dsim_transfer { +DSIM_TRANSFER_NEITHER =0 , +DSIM_TRANSFER_BYCPU = (1 <<7 ), +DSIM_TRANSFER_BYLCDC = (1 <<6 ), +DSIM_TRANSFER_BOTH = (0x3 <<6 ) +}; + +enum dsim_lane_change { +DSIM_NO_CHANGE =0 , +DSIM_DATA_LANE_CHANGE =1 , +DSIM_CLOCK_NALE_CHANGE =2 , +DSIM_ALL_LANE_CHANGE =3 , +}; + +enum dsim_int_src { +DSIM_ALL_OF_INTR =0xffffffff , +DSIM_PLL_STABLE = (1 <<31 ), +}; +
<snip>
Quoted 34 lines
arch/arm/plat-s5p/include/plat/dsim.h new file +34
-0+ +/** +* struct s5p_platform_dsim - interface to platform data for mipi-dsi driver. +* +* @clk_name: specifies clock name for mipi-dsi. +* @lcd_panel_name: specifies lcd panel name registered to mipi-dsi driver. +* lcd panel driver searched would be actived. +* @mipi_1_1v_name: specifies mipi 1.1v regulator name. +* @mipi_1_8v_name: specifies mipi 1.8v regulator name. +* @platfrom_rev: specifies platform revision number. +* revision number should become 1. +* @dsim_config: pointer of structure for configuring mipi-dsi controller. +* @dsim_lcd_info: pointer to structure for configuring +* mipi-dsi based lcd panel. +* @mipi_power: callback pointer for enabling or disabling mipi power. +* @part_reset: callback pointer for reseting mipi phy. +* @init_d_phy: callback pointer for enabing d_phy of dsi master. +* @get_fb_frame_done: callback pointer for getting frame done status of the +* display controller(FIMD). +* @trigger: callback pointer for triggering display controller(FIMD) +* in case of CPU mode. +* @delay_for_stabilization: specifies stable time. +* this delay needs when writing data on SFR +* after mipi mode became LP mode. +*/ +struct s5p_platform_dsim { +char *clk_name; +char *mipi_1_1v_name; +char *mipi_1_8v_name; +char lcd_panel_name[64 ]; +unsigned int platform_rev; + +struct dsim_config *dsim_info; +struct dsim_lcd_config *dsim_lcd_info;
arch/arm/plat-s5p/include/plat/dsim.h line 304
Quoted 10 lines
arch/arm/plat-s5p/include/plat/dsim.h new file +10
-0+ +unsigned int delay_for_stabilization; + +int (*mipi_power) (struct dsim_global *dsim, +struct regulator *p_mipi_1_1v, +struct regulator *p_mipi_1_8v,unsigned int enable); +int (*part_reset) (struct dsim_global *dsim); +int (*init_d_phy) (struct dsim_global *dsim); +int (*get_fb_frame_done) (struct fb_info *info); +void (*trigger) (struct fb_info *info);
Since we may want to get prepared for the flattened device tree I would rather avoid defining fancy callbacks in the platform data struct.
<snip>
Quoted 279 lines
arch/arm/plat-s5p/include/plat/dsim.h new file +2
-0+ +#endif /* _MIPI_DDI_H */ arch/arm/plat-s5p/include/plat/regs-dsim.h new file +271
-0@@ -0,0 +1,281 @@ +/* linux/arch/arm/plat-s5p/include/plat/regs-dsim.h +* +* Register definition file for Samsung MIPI-DSIM driver +* +* InKi Dae<[email protected]>, Copyright (c) 2009 Samsung Electronics +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +*/ + +#ifndef _REGS_DSIM_H +#define _REGS_DSIM_H + +#define S5P_DSIM_STATUS (0x0)/* Status register */ +#define S5P_DSIM_SWRST (0x4)/* Software reset register */ +#define S5P_DSIM_CLKCTRL (0x8)/* Clock control register */ +#define S5P_DSIM_TIMEOUT (0xc)/* Time out register */ +#define S5P_DSIM_CONFIG (0x10)/* Configuration register */ +#define S5P_DSIM_ESCMODE (0x14)/* Escape mode register */ + +/* Main display image resolution register */ +#define S5P_DSIM_MDRESOL (0x18) +#define S5P_DSIM_MVPORCH (0x1c)/* Main display Vporch register */ +#define S5P_DSIM_MHPORCH (0x20)/* Main display Hporch register */ +#define S5P_DSIM_MSYNC (0x24)/* Main display sync area register */ + +/* Sub display image resolution register */ +#define S5P_DSIM_SDRESOL (0x28) +#define S5P_DSIM_INTSRC (0x2c)/* Interrupt source register */ +#define S5P_DSIM_INTMSK (0x30)/* Interrupt mask register */ +#define S5P_DSIM_PKTHDR (0x34)/* Packet Header FIFO register */ +#define S5P_DSIM_PAYLOAD (0x38)/* Payload FIFO register */ +#define S5P_DSIM_RXFIFO (0x3c)/* Read FIFO register */ +#define S5P_DSIM_FIFOTHLD (0x40)/* FIFO threshold level register */ +#define S5P_DSIM_FIFOCTRL (0x44)/* FIFO status and control register */ + +/* FIFO memory AC characteristic register */ +#define S5P_DSIM_MEMACCHR (0x48) +#define S5P_DSIM_PLLCTRL (0x4c)/* PLL control register */ +#define S5P_DSIM_PLLTMR (0x50)/* PLL timer register */ +#define S5P_DSIM_PHYACCHR (0x54)/* D-PHY AC characteristic register */ +#define S5P_DSIM_PHYACCHR1 (0x58)/* D-PHY AC characteristic register1 */ + +/* DSIM_SWRST */ +#define DSIM_FUNCRST (1<< 16) +#define DSIM_SWRST (1<< 0) + +/* S5P_DSIM_TIMEOUT */ +#define DSIM_LPDR_TOUT_SHIFT (0) +#define DSIM_BTA_TOUT_SHIFT (16) +#define DSIM_LPDR_TOUT (x) (((x)& 0xffff)<< DSIM_LPDR_TOUT_SHIFT) +#define DSIM_BTA_TOUT (x) (((x)& 0xff)<< DSIM_BTA_TOUT_SHIFT) + +/* S5P_DSIM_CLKCTRL */ +#define DSIM_ESC_PRESCALER_SHIFT (0) +#define DSIM_LANE_ESC_CLKEN_SHIFT (19) +#define DSIM_BYTE_CLKEN_SHIFT (24) +#define DSIM_BYTE_CLK_SRC_SHIFT (25) +#define DSIM_PLL_BYPASS_SHIFT (27) +#define DSIM_ESC_CLKEN_SHIFT (28) +#define DSIM_TX_REQUEST_HSCLK_SHIFT (31) +#define DSIM_ESC_PRESCALER (x) (((x)& 0xffff)<< \ + DSIM_ESC_PRESCALER_SHIFT) +#define DSIM_LANE_ESC_CLKEN (x) (((x)& 0x1f)<< \ + DSIM_LANE_ESC_CLKEN_SHIFT) +#define DSIM_BYTE_CLK_ENABLE (1<< DSIM_BYTE_CLKEN_SHIFT) +#define DSIM_BYTE_CLK_DISABLE (0<< DSIM_BYTE_CLKEN_SHIFT) +#define DSIM_BYTE_CLKSRC (x) (((x)& 0x3)<< DSIM_BYTE_CLK_SRC_SHIFT) +#define DSIM_PLL_BYPASS_PLL (0<< DSIM_PLL_BYPASS_SHIFT) +#define DSIM_PLL_BYPASS_EXTERNAL (1<< DSIM_PLL_BYPASS_SHIFT) +#define DSIM_ESC_CLKEN_ENABLE (1<< DSIM_ESC_CLKEN_SHIFT) +#define DSIM_ESC_CLKEN_DISABLE (0<< DSIM_ESC_CLKEN_SHIFT) + +/* S5P_DSIM_CONFIG */ +#define DSIM_LANE_EN_SHIFT (0) +#define DSIM_NUM_OF_DATALANE_SHIFT (5) +#define DSIM_SUB_PIX_FORMAT_SHIFT (8) +#define DSIM_MAIN_PIX_FORMAT_SHIFT (12) +#define DSIM_SUB_VC_SHIFT (16) +#define DSIM_MAIN_VC_SHIFT (18) +#define DSIM_HSA_MODE_SHIFT (20) +#define DSIM_HBP_MODE_SHIFT (21) +#define DSIM_HFP_MODE_SHIFT (22) +#define DSIM_HSE_MODE_SHIFT (23) +#define DSIM_AUTO_MODE_SHIFT (24) +#define DSIM_VIDEO_MODE_SHIFT (25) +#define DSIM_BURST_MODE_SHIFT (26) +#define DSIM_SYNC_INFORM_SHIFT (27) +#define DSIM_EOT_R03_SHIFT (28) +#define DSIM_LANE_ENx (x) ((1)<< x) + +/* in case of Gemunus, it should be 0x1. */ +#define DSIM_NUM_OF_DATA_LANE (x) ((x)<< 5) +#define DSIM_SUB_PIX_FORMAT_3BPP (0<< 8)/* command mode only */ +#define DSIM_SUB_PIX_FORMAT_8BPP (1<< 8)/* command mode only */ +#define DSIM_SUB_PIX_FORMAT_12BPP (2<< 8)/* command mode only */ +#define DSIM_SUB_PIX_FORMAT_16BPP (3<< 8)/* command mode only */ +#define DSIM_SUB_PIX_FORMAT_16BPP_RGB (4<< 8)/* video mode only */ +#define DSIM_SUB_PIX_FORMAT_18BPP_PRGB (5<< 8)/* video mode only */ +#define DSIM_SUB_PIX_FORMAT_18BPP_LRGB (6<< 8)/* common */ +#define DSIM_SUB_PIX_FORMAT_24BPP_RGB (7<< 8)/* common */ +#define DSIM_MAIN_PIX_FORMAT_3BPP (0<< 12)/* command mode only */ +#define DSIM_MAIN_PIX_FORMAT_8BPP (1<< 12)/* command mode only */ +#define DSIM_MAIN_PIX_FORMAT_12BPP (2<< 12)/* command mode only */ +#define DSIM_MAIN_PIX_FORMAT_16BPP (3<< 12)/* command mode only */ +#define DSIM_MAIN_PIX_FORMAT_16BPP_RGB (4<< 12)/* video mode only */ +#define DSIM_MAIN_PIX_FORMAT_18BPP_PRGB (5<< 12)/* video mode only */ +#define DSIM_MAIN_PIX_FORMAT_18BPP_LRGB (6<< 12)/* common */ +#define DSIM_MAIN_PIX_FORMAT_24BPP_RGB (7<< 12)/* common */ + +/* Virtual channel number for sub display */ +#define DSIM_SUB_VC (x) (((x)& 0x3)<< 16) +/* Virtual channel number for main display */ +#define DSIM_MAIN_VC (x) (((x)& 0x3)<< 18) +#define DSIM_HSA_MODE_ENABLE (1<< 20) +#define DSIM_HSA_MODE_DISABLE (0<< 20) +#define DSIM_HBP_MODE_ENABLE (1<< 21) +#define DSIM_HBP_MODE_DISABLE (0<< 21) +#define DSIM_HFP_MODE_ENABLE (1<< 22) +#define DSIM_HFP_MODE_DISABLE (0<< 22) +#define DSIM_HSE_MODE_ENABLE (1<< 23) +#define DSIM_HSE_MODE_DISABLE (0<< 23) +#define DSIM_AUTO_MODE (1<< 24) +#define DSIM_CONFIGURATION_MODE (0<< 24) +#define DSIM_VIDEO_MODE (1<< 25) +#define DSIM_COMMAND_MODE (0<< 25) +#define DSIM_BURST_MODE (1<< 26) +#define DSIM_NON_BURST_MODE (0<< 26) +#define DSIM_SYNC_INFORM_PULSE (1<< 27) +#define DSIM_SYNC_INFORM_EVENT (0<< 27) +/* enable EoT packet generation for V1.01r11 */ +#define DSIM_EOT_R03_ENABLE (0<< 28) +/* disable EoT packet generation for V1.01r03 */ +#define DSIM_EOT_R03_DISABLE (1<< 28) + +/* S5P_DSIM_ESCMODE */ +#define DSIM_STOP_STATE_CNT_SHIFT (21) +#define DSIM_STOP_STATE_CNT (x) (((x)& 0x3ff)<< \ + DSIM_STOP_STATE_CNT_SHIFT) +#define DSIM_FORCE_STOP_STATE_SHIFT (20) +#define DSIM_FORCE_BTA_SHIFT (16) +#define DSIM_CMD_LPDT_HS_MODE (0<< 7) +#define DSIM_CMD_LPDT_LP_MODE (1<< 7) +#define DSIM_TX_LPDT_HS_MODE (0<< 6) +#define DSIM_TX_LPDT_LP_MODE (1<< 6) +#define DSIM_TX_TRIGGER_RST_SHIFT (4) +#define DSIM_TX_UIPS_DAT_SHIFT (3) +#define DSIM_TX_UIPS_EXIT_SHIFT (2) +#define DSIM_TX_UIPS_CLK_SHIFT (1) +#define DSIM_TX_UIPS_CLK_EXIT_SHIFT (0) + +/* S5P_DSIM_MDRESOL */ +#define DSIM_MAIN_STAND_BY (1<< 31) +#define DSIM_MAIN_NOT_READY (0<< 31) +#define DSIM_MAIN_VRESOL (x) (((x)& 0x7ff)<< 16) +#define DSIM_MAIN_HRESOL (x) (((x)& 0X7ff)<< 0) + +/* S5P_DSIM_MVPORCH */ +#define DSIM_CMD_ALLOW_SHIFT (28) +#define DSIM_STABLE_VFP_SHIFT (16) +#define DSIM_MAIN_VBP_SHIFT (0) +#define DSIM_CMD_ALLOW_MASK (0xf<< DSIM_CMD_ALLOW_SHIFT) +#define DSIM_STABLE_VFP_MASK (0x7ff<< DSIM_STABLE_VFP_SHIFT) +#define DSIM_MAIN_VBP_MASK (0x7ff<< DSIM_MAIN_VBP_SHIFT) +#define DSIM_CMD_ALLOW (x) (((x)& 0xf)<< DSIM_CMD_ALLOW_SHIFT) +#define DSIM_STABLE_VFP (x) (((x)& 0x7ff)<< DSIM_STABLE_VFP_SHIFT) +#define DSIM_MAIN_VBP (x) (((x)& 0x7ff)<< DSIM_MAIN_VBP_SHIFT) + +/* S5P_DSIM_MHPORCH */ +#define DSIM_MAIN_HFP_SHIFT (16) +#define DSIM_MAIN_HBP_SHIFT (0) +#define DSIM_MAIN_HFP_MASK ((0xffff)<< DSIM_MAIN_HFP_SHIFT) +#define DSIM_MAIN_HBP_MASK ((0xffff)<< DSIM_MAIN_HBP_SHIFT) +#define DSIM_MAIN_HFP (x) (((x)& 0xffff)<< DSIM_MAIN_HFP_SHIFT) +#define DSIM_MAIN_HBP (x) (((x)& 0xffff)<< DSIM_MAIN_HBP_SHIFT) + +/* S5P_DSIM_MSYNC */ +#define DSIM_MAIN_VSA_SHIFT (22) +#define DSIM_MAIN_HSA_SHIFT (0) +#define DSIM_MAIN_VSA_MASK ((0x3ff)<< DSIM_MAIN_VSA_SHIFT) +#define DSIM_MAIN_HSA_MASK ((0xffff)<< DSIM_MAIN_HSA_SHIFT) +#define DSIM_MAIN_VSA (x) (((x)& 0x3ff)<< DSIM_MAIN_VSA_SHIFT) +#define DSIM_MAIN_HSA (x) (((x)& 0xffff)<< DSIM_MAIN_HSA_SHIFT) + +/* S5P_DSIM_SDRESOL */ +#define DSIM_SUB_STANDY_SHIFT (31) +#define DSIM_SUB_VRESOL_SHIFT (16) +#define DSIM_SUB_HRESOL_SHIFT (0) +#define DSIM_SUB_STANDY_MASK ((0x1)<< DSIM_SUB_STANDY_SHIFT) +#define DSIM_SUB_VRESOL_MASK ((0x7ff)<< DSIM_SUB_VRESOL_SHIFT) +#define DSIM_SUB_HRESOL_MASK ((0x7ff)<< DSIM_SUB_HRESOL_SHIFT) +#define DSIM_SUB_STANDY (1<< DSIM_SUB_STANDY_SHIFT) +#define DSIM_SUB_NOT_READY (0<< DSIM_SUB_STANDY_SHIFT) +#define DSIM_SUB_VRESOL (x) (((x)& 0x7ff)<< DSIM_SUB_VRESOL_SHIFT) +#define DSIM_SUB_HRESOL (x) (((x)& 0x7ff)<< DSIM_SUB_HRESOL_SHIFT) + +/* S5P_DSIM_INTSRC */ +#define INTSRC_ERR_CONTENT_LP1 (1<< 0) +#define INTSRC_ERR_CONTENT_LP0 (1<< 1) +#define INTSRC_ERR_CONTROL0 (1<< 2) +#define INTSRC_ERR_CONTROL1 (1<< 3) +#define INTSRC_ERR_CONTROL2 (1<< 4) +#define INTSRC_ERR_CONTROL3 (1<< 5) +#define INTSRC_ERR_SYNC0 (1<< 6) +#define INTSRC_ERR_SYNC1 (1<< 7) +#define INTSRC_ERR_SYNC2 (1<< 8) +#define INTSRC_ERR_SYNC3 (1<< 9) +#define INTSRC_ERR_ESC0 (1<< 10) +#define INTSRC_ERR_ESC1 (1<< 11) +#define INTSRC_ERR_ESC2 (1<< 12) +#define INTSRC_ERR_ESC3 (1<< 13) +#define INTSRC_ERR_RX_CRC (1<< 14) +#define INTSRC_ERR_RX_ECC (1<< 15) +#define INTSRC_RX_ACK (1<< 16) +#define INTSRC_RX_TE (1<< 17) +#define INTSRC_RX_DAT_DONE (1<< 18) +#define INTSRC_TA_TOUT (1<< 20) +#define INTSRC_LPDR_TOUT (1<< 21) +#define INTSRC_FRAME_DONE (1<< 24) +#define INTSRC_BUS_TURN_OVER (1<< 25) +#define INTSRC_SYNC_OVERRIDE (1<< 28) +#define INTSRC_SFR_FIFO_EMPTY (1<< 29) +#define INTSRC_SW_RST_RELEASE (1<< 30) +#define INTSRC_PLL_STABLE (1<< 31) + +/* S5P_DSIM_INTMSK */ +#define INTMSK_ERR_CONTENT_LP1 (1<< 0) +#define INTMSK_ERR_CONTENT_LP0 (1<< 1) +#define INTMSK_ERR_CONTROL0 (1<< 2) +#define INTMSK_ERR_CONTROL1 (1<< 3) +#define INTMSK_ERR_CONTROL2 (1<< 4) +#define INTMSK_ERR_CONTROL3 (1<< 5) +#define INTMSK_ERR_SYNC0 (1<< 6) +#define INTMSK_ERR_SYNC1 (1<< 7) +#define INTMSK_ERR_SYNC2 (1<< 8) +#define INTMSK_ERR_SYNC3 (1<< 9) +#define INTMSK_ERR_ESC0 (1<< 10) +#define INTMSK_ERR_ESC1 (1<< 11) +#define INTMSK_ERR_ESC2 (1<< 12) +#define INTMSK_ERR_ESC3 (1<< 13) +#define INTMSK_ERR_RX_CRC (1<< 14) +#define INTMSK_ERR_RX_ECC (1<< 15) +#define INTMSK_RX_ACK (1<< 16) +#define INTMSK_RX_TE (1<< 17) +#define INTMSK_RX_DAT_DONE (1<< 18) +#define INTMSK_TA_TOUT (1<< 20) +#define INTMSK_LPDR_TOUT (1<< 21) +#define INTMSK_FRAME_DONE (1<< 24) +#define INTMSK_BUS_TURN_OVER (1<< 25) +#define INTMSK_SFR_FIFO_EMPTY (1<< 29) +#define INTMSK_SW_RST_RELEASE (1<< 30) +#define INTMSK_PLL_STABLE (1<< 31) + +/* S5P_DSIM_PKTHDR */ +#define DSIM_PACKET_HEADER_DI (x) (((x)& 0xff)<< 0) +/* Word count lower byte for long packet */ +#define DSIM_PACKET_HEADER_DAT0 (x) (((x)& 0xff)<< 8) +/* Word count upper byte for long packet */ +#define DSIM_PACKET_HEADER_DAT1 (x) (((x)& 0xff)<< 16) + +/* S5P_DSIM_FIFOCTRL */ +#define DSIM_RX_FIFO (1<< 4) +#define DSIM_TX_SFR_FIFO (1<< 3) +#define DSIM_I80_FIFO (1<< 2) +#define DSIM_SUB_DISP_FIFO (1<< 1) +#define DSIM_MAIN_DISP_FIFO (1<< 0) + +/* S5P_DSIM_PHYACCHR */ +#define DSIM_AFC_CTL (x) (((x)& 0x7)<< 5) +#define DSIM_AFC_ENABLE (1<< 14)
arch/arm/plat-s5p/include/plat/regs-dsim.h line 281
Quoted 10 lines
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +10
-0+#define DSIM_AFC_DISABLE (0<< 14) + +/* S5P_DSIM_PLLCTRL */ +#define DSIM_PMS_SHIFT (1) +#define DSIM_PLL_EN_SHIFT (23) +#define DSIM_FREQ_BAND_SHIFT (24) +#define DSIM_PMS (x) (((x)& 0x7ffff)<< DSIM_PMS_SHIFT) +#define DSIM_FREQ_BAND (x) (((x)& 0xf)<< DSIM_FREQ_BAND_SHIFT) + +#endif /* _REGS_DSIM_H */
All these registers' definitions seem to be referenced only from one driver in drivers/video/s5p_dsim*.c. How about creating s5p-dsim directory in drivers/video/ and moving this whole pile of definitions there?
Also please see this thread
http://www.mail-archive.com/linux-media at vger.kernel.org/msg21129.html for more insight.
Quoted 76 lines
drivers/video/Kconfig +7
-0@@ -1996,6 +1996,13 @@ config FB_S3C2410_DEBUG Turn on debugging messages. Note that you can set/unset at run time through sysfs +config S5P_MIPI_DSI + tristate "Samsung SoC MIPI-DSI support." + depends on FB_S3C&& ARCH_S5PV210 + default n + help + This enables support for MIPI-DSI device for samsung SoC S5PV210. + config FB_NUC900 bool "NUC900 LCD framebuffer support" depends on FB&& ARCH_W90X900drivers/video/Makefile +2
-0@@ -115,6 +115,8 @@ obj-$(CONFIG_FB_SH7760) += sh7760fb.o obj-$(CONFIG_FB_IMX) += imxfb.o obj-$(CONFIG_FB_S3C) += s3c-fb.o obj-$(CONFIG_FB_S3C2410) += s3c2410fb.o +obj-$(CONFIG_S5P_MIPI_DSI) += s5p-dsim.o s5p_dsim_common.o \ + s5p_dsim_lowlevel.o obj-$(CONFIG_FB_FSL_DIU) += fsl-diu-fb.o obj-$(CONFIG_FB_COBALT) += cobalt_lcdfb.o obj-$(CONFIG_FB_PNX4008_DUM) += pnx4008/drivers/video/s5p-dsim.c new file +39
-0@@ -0,0 +1,463 @@ +/* linux/drivers/video/s5p-dsim.c +* +* Samsung MIPI-DSIM driver. +* +* InKi Dae,<[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +*/ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/errno.h> +#include <linux/clk.h> +#include <linux/mutex.h> +#include <linux/wait.h> +#include <linux/fs.h> +#include <linux/mm.h> +#include <linux/fb.h> +#include <linux/ctype.h> +#include <linux/platform_device.h> +#include <linux/io.h> +#include <linux/irq.h> +#include <linux/memory.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/kthread.h> +#include <linux/regulator/consumer.h> +#include <linux/notifier.h> + +#include <plat/fb.h> +#include <plat/regs-dsim.h> +#include <plat/dsim.h> +#include <plat/mipi_ddi.h> + +#include <mach/map.h> + +#include "s5p_dsim_common.h"
drivers/video/s5p-dsim.c line 49
Quoted 10 lines
drivers/video/s5p-dsim.c new file +10
-0+ +struct mipi_lcd_info { +struct list_head list; +struct mipi_lcd_driver *mipi_drv; +}; + +static LIST_HEAD (lcd_info_list); +static DEFINE_MUTEX (mipi_lock); + +struct dsim_global dsim;
Using a global variable like this seems rather hacky.. The driver will not be usable when there are more than one instance of the s5p-dsim device in the system. Or is it impossible that there could be multiple entities of MIPI-DSIM in the SoC?
How about allocating an instance of struct dsim_global (and perhaps changing it's name since it's not global any more?..) during device probing and storing a pointer to it in driver's private data in struct device/platform_device? Isn't that doable?
Regards,
Sylwester
Quoted 71 lines
drivers/video/s5p-dsim.c new file +71
-0+ +struct s5p_platform_dsim *to_dsim_plat (struct device *dev) +{ +struct platform_device *pdev =to_platform_device (dev); + +return (struct s5p_platform_dsim *)pdev->dev.platform_data; +} + +/* +* notifier callback function for fb_blank +* - this function would be called by device specific fb_blank. +*/ +static int s5p_dsim_notifier_callback (struct notifier_block *self, +unsigned long event,void *data) +{ +switch (event) { +case FB_BLANK_UNBLANK : +case FB_BLANK_NORMAL : +if (dsim.pd->mipi_power) + dsim.pd->mipi_power (&dsim, dsim.r_mipi_1_1v, + dsim.r_mipi_1_8v,1 ); + +clk_enable (dsim.clock); + +if (dsim.mipi_drv->resume) + dsim.mipi_drv->resume (dsim.dev); + +s5p_dsim_init_dsim (&dsim); +s5p_dsim_init_link (&dsim); + +s5p_dsim_set_hs_enable (&dsim); +s5p_dsim_set_data_transfer_mode (&dsim, +DSIM_TRANSFER_BYCPU ,1 ); + +/* it needs delay for stabilization */ +mdelay (dsim.pd->delay_for_stabilization); + +if (dsim.mipi_drv->init) + dsim.mipi_drv->init (dsim.dev); +else +dev_warn (dsim.dev,"init func is null.\n" ); + +s5p_dsim_set_display_mode (&dsim, dsim.dsim_lcd_info,NULL ); + +s5p_dsim_set_data_transfer_mode (&dsim,DSIM_TRANSFER_BYLCDC ,1 ); + dsim.mipi_ddi_pd->resume_complete =1 ; + +dev_dbg (dsim.dev,"FB_BLANK_NORMAL or UNBLANK.\n" ); + +break ; +case FB_BLANK_POWERDOWN : + dsim.mipi_ddi_pd->resume_complete =0 ; + +if (dsim.mipi_drv->suspend) + dsim.mipi_drv->suspend (dsim.dev); + +clk_disable (dsim.clock); + +if (dsim.pd->mipi_power) + dsim.pd->mipi_power (&dsim, dsim.r_mipi_1_1v, + dsim.r_mipi_1_8v,0 ); + +dev_dbg (dsim.dev,"FB_BLANK_POWERDOWN.\n" ); +break ; +default : +dev_warn (dsim.dev,"unknown FB_BLANK command.\n" ); +break ; + } + +return 0 ; +}
<snip>
Signature · 2 lines
Regards, Sylwester
PATCH 4/4 S5PC110: add MIPI-DSI driver.
Thank you for your comments.
Quoted 96 lines
-----Original Message-----
From: Sylwester Nawrocki [mailto:spnlinux at gmail.com]
Sent: Sunday, November 28, 2010 2:59 AM
To: Inki Dae
Cc: linux-fbdev at vger.kernel.org; linux-arm-kernel at lists.infradead.org; kyungmin.park at samsung.com; kgene.kim at samsung.com; akpm at linux- foundation.org; lethal at linux-sh.org
Subject: Re: [PATCH 4/4] S5PC110: add MIPI-DSI driver.Hello,
Quoted 9 lines · Inki Dae
driver features:
. Maximum resolution ranges up to XGA (1024x760)
. CSIS0 supports 1,2,3 or 4 data lanes
. CSIS1 supports 1 or 2 data lanes
. support pixel format : 16bpp, 18bpp packed,
18bpp loosely packed (3 byte format), and 24bpp
(now would use 24bpp)
. support RGB interface for video image from display controller . support I80 interface for command mode image input from displaycontroller
Quoted 1 line
. support PMS control interface for PLL to configure byte clock
frequency
Quoted 4 lines
. support Prescaler to generate escape clock from byte clock
Signed-off-by Inki Dae<[email protected]>Signed-off-by Kyungmin Park<[email protected]>Quoted 8 lines
--- arch/arm/plat-s5p/include/plat/dsim.h | 470 +++++++++++++++++++ arch/arm/plat-s5p/include/plat/mipi_ddi.h | 94 ++++ arch/arm/plat-s5p/include/plat/regs-dsim.h | 281 +++++++++++ drivers/video/Kconfig | 7 + drivers/video/Makefile | 2 + drivers/video/s5p-dsim.c | 463 +++++++++++++++++++ drivers/video/s5p_dsim_common.c | 691++++++++++++++++++++++++++++
arch/arm/plat-
Quoted 14 lines
drivers/video/s5p_dsim_common.h | 35 ++ drivers/video/s5p_dsim_lowlevel.c | 569 +++++++++++++++++++++++ drivers/video/s5p_dsim_lowlevel.h | 101 ++++ 10 files changed, 2713 insertions(+), 0 deletions(-)create mode 100644
arch/arm/plat-s5p/include/plat/dsim.hcreate mode 100644arch/arm/plat-s5p/include/plat/mipi_ddi.hcreate mode 100644arch/arm/plat-s5p/include/plat/regs-dsim.hcreate mode 100644drivers/video/s5p-dsim.c
create mode 100644drivers/video/s5p_dsim_common.ccreate mode 100644drivers/video/s5p_dsim_common.hcreate mode 100644drivers/video/s5p_dsim_lowlevel.ccreate mode 100644drivers/video/s5p_dsim_lowlevel.harch/arm/plat- renamed from arch/arm/plat-s5p/include/plat/dsim.h +0
-0
s5p/include/plat/dsim.hQuoted 44 lines
new file mode 100644
index 0000000..14bc13farch/arm/plat-s5p/include/plat/dsim.h new file +39
-0@@ -0,0 +1,470 @@ +/* linux/arm/arch/plat-s5p/include/plat/dsim.h +* +* Platform data header for Samsung MIPI-DSIM. +* +* Copyright (c) 2009 Samsung Electronics +* InKi Dae<[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +*/ + +#ifndef _DSIM_H +#define _DSIM_H + +#include <linux/device.h> + +/* h/w configuration */ +#define MIPI_FIN 24000000 + +#define DSIM_TRUE 1 +#define DSIM_FALSE 0 + +#define DSIM_HEADER_FIFO_SZ 16 + +enum dsim_interface_type { +DSIM_COMMAND =0 , +DSIM_VIDEO =1 , +}; + +enum dsim_state { +DSIM_STATE_RESET =0 , +DSIM_STATE_INIT =1 , +DSIM_STATE_STOP =2 , +DSIM_STATE_HSCLKEN =3 , +DSIM_STATE_ULPS =4 , +}; + +enum dsim_virtual_ch_no {
Quoted 9 lines
arch/arm/plat-s5p/include/plat/dsim.h line 44
Quoted 5 lines
arch/arm/plat-s5p/include/plat/dsim.h new file +5
-0+DSIM_VIRTUAL_CH_0 =0 , +DSIM_VIRTUAL_CH_1 =1 , +DSIM_VIRTUAL_CH_2 =2 , + DSIM_VIRTUAL_CH_3 = 3, +};The enum type suggest the meaning so what is the point of redefining numbers?
Ok, it would be cleaned.
Quoted 133 lines
Quoted 89 lines
arch/arm/plat-s5p/include/plat/dsim.h new file +89
-0+ +enum dsim_video_mode_type { +DSIM_NON_BURST_SYNC_EVENT =0 , +DSIM_NON_BURST_SYNC_PULSE =2 , +DSIM_BURST =3 , +DSIM_NON_VIDEO_MODE =4 , +}; + +enum dsim_fifo_state { +DSIM_RX_DATA_FULL = (1 <<25 ), +DSIM_RX_DATA_EMPTY = (1 <<24 ), +SFR_HEADER_FULL = (1 <<23 ), +SFR_HEADER_EMPTY = (1 <<22 ), +SFR_PAYLOAD_FULL = (1 <<21 ), +SFR_PAYLOAD_EMPTY = (1 <<20 ), +I80_HEADER_FULL = (1 <<19 ), +I80_HEADER_EMPTY = (1 <<18 ), +I80_PALOAD_FULL = (1 <<17 ), +I80_PALOAD_EMPTY = (1 <<16 ), +SUB_DISP_HEADER_FULL = (1 <<15 ), +SUB_DISP_HEADER_EMPTY = (1 <<14 ), +SUB_DISP_PAYLOAD_FULL = (1 <<13 ), +SUB_DISP_PAYLOAD_EMPTY = (1 <<12 ), +MAIN_DISP_HEADER_FULL = (1 <<11 ), +MAIN_DISP_HEADER_EMPTY = (1 <<10 ), +MAIN_DISP_PAYLOAD_FULL = (1 <<9 ), +MAIN_DISP_PAYLOAD_EMPTY = (1 <<8 ), +}; + +enum dsim_no_of_data_lane { +DSIM_DATA_LANE_1 =0 , +DSIM_DATA_LANE_2 =1 , +DSIM_DATA_LANE_3 =2 , +DSIM_DATA_LANE_4 =3 , +}; + +enum dsim_byte_clk_src { +DSIM_PLL_OUT_DIV8 =0 , +DSIM_EXT_CLK_DIV8 =1 , +DSIM_EXT_CLK_BYPASS =2 , +}; + +enum dsim_lane { +DSIM_LANE_DATA0 = (1 <<0 ), +DSIM_LANE_DATA1 = (1 <<1 ), +DSIM_LANE_DATA2 = (1 <<2 ), +DSIM_LANE_DATA3 = (1 <<3 ), +DSIM_LANE_DATA_ALL =0xf , +DSIM_LANE_CLOCK = (1 <<4 ), +DSIM_LANE_ALL =DSIM_LANE_CLOCK |DSIM_LANE_DATA_ALL , +}; + +enum dsim_pixel_format { +DSIM_CMD_3BPP =0 , +DSIM_CMD_8BPP =1 , +DSIM_CMD_12BPP =2 , +DSIM_CMD_16BPP =3 , +DSIM_VID_16BPP_565 =4 , +DSIM_VID_18BPP_666PACKED =5 , +DSIM_18BPP_666LOOSELYPACKED =6 , +DSIM_24BPP_888 =7 , +}; + +enum dsim_lane_state { +DSIM_LANE_STATE_HS_READY , +DSIM_LANE_STATE_ULPS , +DSIM_LANE_STATE_STOP , +DSIM_LANE_STATE_LPDT , +}; + +enum dsim_transfer { +DSIM_TRANSFER_NEITHER =0 , +DSIM_TRANSFER_BYCPU = (1 <<7 ), +DSIM_TRANSFER_BYLCDC = (1 <<6 ), +DSIM_TRANSFER_BOTH = (0x3 <<6 ) +}; + +enum dsim_lane_change { +DSIM_NO_CHANGE =0 , +DSIM_DATA_LANE_CHANGE =1 , +DSIM_CLOCK_NALE_CHANGE =2 , +DSIM_ALL_LANE_CHANGE =3 , +}; + +enum dsim_int_src { +DSIM_ALL_OF_INTR =0xffffffff , +DSIM_PLL_STABLE = (1 <<31 ), +}; +<snip>
arch/arm/plat-s5p/include/plat/dsim.h
Quoted 3 lines
arch/arm/plat-s5p/include/plat/dsim.h new file +3
-0+ +/** +* struct s5p_platform_dsim - interface to platform data for mipi-dsi driver.
Quoted 3 lines
+ *
+ * @clk_name: specifies clock name for mipi-dsi.
+ * @lcd_panel_name: specifies lcd panel name registered to mipi-dsidriver.
Quoted 6 lines
+ * lcd panel driver searched would be actived.
+ * @mipi_1_1v_name: specifies mipi 1.1v regulator name.
+ * @mipi_1_8v_name: specifies mipi 1.8v regulator name.
+ * @platfrom_rev: specifies platform revision number.
+ * revision number should become 1.
+ * @dsim_config: pointer of structure for configuring mipi-dsicontroller.
Quoted 6 lines
+ * @dsim_lcd_info: pointer to structure for configuring
+ * mipi-dsi based lcd panel.
+ * @mipi_power: callback pointer for enabling or disabling mipi power.
+ * @part_reset: callback pointer for reseting mipi phy.
+ * @init_d_phy: callback pointer for enabingd_phyof dsi master.
+ * @get_fb_frame_done: callback pointer for getting frame done statusof the
Quoted 21 lines
+ * display controller(FIMD).
+ * @trigger: callback pointer for triggering display controller(FIMD)
+ * in case of CPU mode.
+ * @delay_for_stabilization: specifies stable time.
+ * this delay needs when writing data on SFR
+ * after mipi mode became LP mode.
+ */arch/arm/plat-s5p/include/plat/dsim.h new file +14
-0+struct s5p_platform_dsim { +char *clk_name; +char *mipi_1_1v_name; +char *mipi_1_8v_name; +char lcd_panel_name[64 ]; +unsigned int platform_rev; + +struct dsim_config *dsim_info; +struct dsim_lcd_config *dsim_lcd_info; + +unsigned int delay_for_stabilization; + + int (*mipi_power) (struct dsim_global *dsim, + struct regulator *p_mipi_1_1v,
Quoted 9 lines
arch/arm/plat-s5p/include/plat/dsim.h line 304
Quoted 5 lines
arch/arm/plat-s5p/include/plat/dsim.h new file +5
-0+ struct regulator *p_mipi_1_8v, unsigned int enable); +int (*part_reset) (struct dsim_global *dsim); +int (*init_d_phy) (struct dsim_global *dsim); +int (*get_fb_frame_done) (struct fb_info *info); +void (*trigger) (struct fb_info *info);Since we may want to get prepared for the flattened device tree I would rather avoid defining fancy callbacks in the platform data struct.
These callbacks are for connection between device driver and machine specific code or functions of another driver such as fimd. By defining callbacks, all machines could use common interface.
Quoted 319 lines
<snip>
arch/arm/plat-
Quoted 3 lines
arch/arm/plat-s5p/include/plat/dsim.h new file +2
-0+ +#endif /* _MIPI_DDI_H */ arch/arm/plat- renamed from arch/arm/plat-s5p/include/plat/regs-dsim.h +0
-0
s5p/include/plat/regs-dsim.harch/arm/plat-s5p/include/plat/regs-dsim.h line 5
Quoted 10 lines
new file mode 100644
index 0000000..c4bfab5arch/arm/plat-s5p/include/plat/regs-dsim.h new file +5
-0@@ -0,0 +1,281 @@ +/* linux/arch/arm/plat-s5p/include/plat/regs-dsim.h +* +* Register definition file for Samsung MIPI-DSIM driver +* +* InKi Dae<[email protected]>, Copyright (c) 2009 Samsung Electronics
Quoted 11 lines
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +11
-0+* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +*/ + +#ifndef _REGS_DSIM_H +#define _REGS_DSIM_H + +#define S5P_DSIM_STATUS (0x0)/* Status register */ +#define S5P_DSIM_SWRST (0x4)/* Software reset register */ arch/arm/plat-s5p/include/plat/regs-dsim.h
Quoted 10 lines
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +10
-0+#define S5P_DSIM_CLKCTRL (0x8)/* Clock control register */ +#define S5P_DSIM_TIMEOUT (0xc)/* Time out register */ +#define S5P_DSIM_CONFIG (0x10)/* Configuration register */ +#define S5P_DSIM_ESCMODE (0x14)/* Escape mode register */ + +/* Main display image resolution register */ +#define S5P_DSIM_MDRESOL (0x18) +#define S5P_DSIM_MVPORCH (0x1c)/* Main display Vporch register */ +#define S5P_DSIM_MHPORCH (0x20)/* Main display Hporch register */ +#define S5P_DSIM_MSYNC (0x24)/* Main display sync area register */
arch/arm/plat-s5p/include/plat/regs-dsim.h
Quoted 9 lines
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +9
-0+ +/* Sub display image resolution register */ +#define S5P_DSIM_SDRESOL (0x28) +#define S5P_DSIM_INTSRC (0x2c)/* Interrupt source register */ +#define S5P_DSIM_INTMSK (0x30)/* Interrupt mask register */ +#define S5P_DSIM_PKTHDR (0x34)/* Packet Header FIFO register */ +#define S5P_DSIM_PAYLOAD (0x38)/* Payload FIFO register */ +#define S5P_DSIM_RXFIFO (0x3c)/* Read FIFO register */ +#define S5P_DSIM_FIFOTHLD (0x40)/* FIFO threshold level register */
arch/arm/plat-s5p/include/plat/regs-dsim.h line 36
Quoted 1 line
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +1
-0+#define S5P_DSIM_FIFOCTRL (0x44)/* FIFO status and control register */
arch/arm/plat-s5p/include/plat/regs-dsim.h
Quoted 6 lines
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +6
-0+ +/* FIFO memory AC characteristic register */ +#define S5P_DSIM_MEMACCHR (0x48) +#define S5P_DSIM_PLLCTRL (0x4c)/* PLL control register */ +#define S5P_DSIM_PLLTMR (0x50)/* PLL timer register */ +#define S5P_DSIM_PHYACCHR (0x54)/* D-PHY AC characteristic register */
arch/arm/plat-s5p/include/plat/regs-dsim.h line 43
Quoted 1 line
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +1
-0+#define S5P_DSIM_PHYACCHR1 (0x58)/* D-PHY AC characteristic register1 */
Quoted 16 lines
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +16
-0+ +/* DSIM_SWRST */ +#define DSIM_FUNCRST (1<< 16) +#define DSIM_SWRST (1<< 0) + +/* S5P_DSIM_TIMEOUT */ +#define DSIM_LPDR_TOUT_SHIFT (0) +#define DSIM_BTA_TOUT_SHIFT (16) +#define DSIM_LPDR_TOUT (x) (((x)& 0xffff)<< DSIM_LPDR_TOUT_SHIFT) +#define DSIM_BTA_TOUT (x) (((x)& 0xff)<< DSIM_BTA_TOUT_SHIFT) + +/* S5P_DSIM_CLKCTRL */ +#define DSIM_ESC_PRESCALER_SHIFT (0) +#define DSIM_LANE_ESC_CLKEN_SHIFT (19) +#define DSIM_BYTE_CLKEN_SHIFT (24) +#define DSIM_BYTE_CLK_SRC_SHIFT (25)arch/arm/plat-s5p/include/plat/regs-dsim.h
Quoted 10 lines
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +10
-0+#define DSIM_PLL_BYPASS_SHIFT (27) +#define DSIM_ESC_CLKEN_SHIFT (28) +#define DSIM_TX_REQUEST_HSCLK_SHIFT (31) +#define DSIM_ESC_PRESCALER (x) (((x)& 0xffff)<< \ + DSIM_ESC_PRESCALER_SHIFT) +#define DSIM_LANE_ESC_CLKEN (x) (((x)& 0x1f)<< \ + DSIM_LANE_ESC_CLKEN_SHIFT) +#define DSIM_BYTE_CLK_ENABLE (1<< DSIM_BYTE_CLKEN_SHIFT) +#define DSIM_BYTE_CLK_DISABLE (0<< DSIM_BYTE_CLKEN_SHIFT) +#define DSIM_BYTE_CLKSRC (x) (((x)& 0x3)<<
DSIM_BYTE_CLK_SRC_SHIFT)Quoted 16 lines
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +16
-0+#define DSIM_PLL_BYPASS_PLL (0<< DSIM_PLL_BYPASS_SHIFT) +#define DSIM_PLL_BYPASS_EXTERNAL (1<< DSIM_PLL_BYPASS_SHIFT) +#define DSIM_ESC_CLKEN_ENABLE (1<< DSIM_ESC_CLKEN_SHIFT) +#define DSIM_ESC_CLKEN_DISABLE (0<< DSIM_ESC_CLKEN_SHIFT) + +/* S5P_DSIM_CONFIG */ +#define DSIM_LANE_EN_SHIFT (0) +#define DSIM_NUM_OF_DATALANE_SHIFT (5) +#define DSIM_SUB_PIX_FORMAT_SHIFT (8) +#define DSIM_MAIN_PIX_FORMAT_SHIFT (12) +#define DSIM_SUB_VC_SHIFT (16) +#define DSIM_MAIN_VC_SHIFT (18) +#define DSIM_HSA_MODE_SHIFT (20) +#define DSIM_HBP_MODE_SHIFT (21) +#define DSIM_HFP_MODE_SHIFT (22) +#define DSIM_HSE_MODE_SHIFT (23)arch/arm/plat-s5p/include/plat/regs-dsim.h
Quoted 10 lines
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +10
-0+#define DSIM_AUTO_MODE_SHIFT (24) +#define DSIM_VIDEO_MODE_SHIFT (25) +#define DSIM_BURST_MODE_SHIFT (26) +#define DSIM_SYNC_INFORM_SHIFT (27) +#define DSIM_EOT_R03_SHIFT (28) +#define DSIM_LANE_ENx (x) ((1)<< x) + +/* in case of Gemunus, it should be 0x1. */ +#define DSIM_NUM_OF_DATA_LANE (x) ((x)<< 5) +#define DSIM_SUB_PIX_FORMAT_3BPP (0<< 8)/* command mode only */
arch/arm/plat-s5p/include/plat/regs-dsim.h line 96
Quoted 1 line
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +1
-0+#define DSIM_SUB_PIX_FORMAT_8BPP (1<< 8)/* command mode only */
arch/arm/plat-s5p/include/plat/regs-dsim.h line 97
Quoted 1 line
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +1
-0+#define DSIM_SUB_PIX_FORMAT_12BPP (2<< 8)/* command mode only */
arch/arm/plat-s5p/include/plat/regs-dsim.h line 98
Quoted 1 line
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +1
-0+#define DSIM_SUB_PIX_FORMAT_16BPP (3<< 8)/* command mode only */
arch/arm/plat-s5p/include/plat/regs-dsim.h line 99
Quoted 1 line
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +1
-0+#define DSIM_SUB_PIX_FORMAT_16BPP_RGB (4<< 8)/* video mode only */
arch/arm/plat-s5p/include/plat/regs-dsim.h line 100
Quoted 1 line
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +1
-0+#define DSIM_SUB_PIX_FORMAT_18BPP_PRGB (5<< 8)/* video mode only */
arch/arm/plat-s5p/include/plat/regs-dsim.h line 103
Quoted 3 lines
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +3
-0+#define DSIM_SUB_PIX_FORMAT_18BPP_LRGB (6<< 8)/* common */ +#define DSIM_SUB_PIX_FORMAT_24BPP_RGB (7<< 8)/* common */ +#define DSIM_MAIN_PIX_FORMAT_3BPP (0<< 12)/* command mode only */
arch/arm/plat-s5p/include/plat/regs-dsim.h line 104
Quoted 1 line
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +1
-0+#define DSIM_MAIN_PIX_FORMAT_8BPP (1<< 12)/* command mode only */
arch/arm/plat-s5p/include/plat/regs-dsim.h line 105
Quoted 1 line
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +1
-0+#define DSIM_MAIN_PIX_FORMAT_12BPP (2<< 12)/* command mode only */
arch/arm/plat-s5p/include/plat/regs-dsim.h line 106
Quoted 1 line
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +1
-0+#define DSIM_MAIN_PIX_FORMAT_16BPP (3<< 12)/* command mode only */
arch/arm/plat-s5p/include/plat/regs-dsim.h line 107
Quoted 1 line
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +1
-0+#define DSIM_MAIN_PIX_FORMAT_16BPP_RGB (4<< 12)/* video mode only */
arch/arm/plat-s5p/include/plat/regs-dsim.h line 108
Quoted 1 line
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +1
-0+#define DSIM_MAIN_PIX_FORMAT_18BPP_PRGB (5<< 12)/* video mode only */
Quoted 48 lines
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +48
-0+#define DSIM_MAIN_PIX_FORMAT_18BPP_LRGB (6<< 12)/* common */ +#define DSIM_MAIN_PIX_FORMAT_24BPP_RGB (7<< 12)/* common */ + +/* Virtual channel number for sub display */ +#define DSIM_SUB_VC (x) (((x)& 0x3)<< 16) +/* Virtual channel number for main display */ +#define DSIM_MAIN_VC (x) (((x)& 0x3)<< 18) +#define DSIM_HSA_MODE_ENABLE (1<< 20) +#define DSIM_HSA_MODE_DISABLE (0<< 20) +#define DSIM_HBP_MODE_ENABLE (1<< 21) +#define DSIM_HBP_MODE_DISABLE (0<< 21) +#define DSIM_HFP_MODE_ENABLE (1<< 22) +#define DSIM_HFP_MODE_DISABLE (0<< 22) +#define DSIM_HSE_MODE_ENABLE (1<< 23) +#define DSIM_HSE_MODE_DISABLE (0<< 23) +#define DSIM_AUTO_MODE (1<< 24) +#define DSIM_CONFIGURATION_MODE (0<< 24) +#define DSIM_VIDEO_MODE (1<< 25) +#define DSIM_COMMAND_MODE (0<< 25) +#define DSIM_BURST_MODE (1<< 26) +#define DSIM_NON_BURST_MODE (0<< 26) +#define DSIM_SYNC_INFORM_PULSE (1<< 27) +#define DSIM_SYNC_INFORM_EVENT (0<< 27) +/* enable EoT packet generation for V1.01r11 */ +#define DSIM_EOT_R03_ENABLE (0<< 28) +/* disable EoT packet generation for V1.01r03 */ +#define DSIM_EOT_R03_DISABLE (1<< 28) + +/* S5P_DSIM_ESCMODE */ +#define DSIM_STOP_STATE_CNT_SHIFT (21) +#define DSIM_STOP_STATE_CNT (x) (((x)& 0x3ff)<< \ + DSIM_STOP_STATE_CNT_SHIFT) +#define DSIM_FORCE_STOP_STATE_SHIFT (20) +#define DSIM_FORCE_BTA_SHIFT (16) +#define DSIM_CMD_LPDT_HS_MODE (0<< 7) +#define DSIM_CMD_LPDT_LP_MODE (1<< 7) +#define DSIM_TX_LPDT_HS_MODE (0<< 6) +#define DSIM_TX_LPDT_LP_MODE (1<< 6) +#define DSIM_TX_TRIGGER_RST_SHIFT (4) +#define DSIM_TX_UIPS_DAT_SHIFT (3) +#define DSIM_TX_UIPS_EXIT_SHIFT (2) +#define DSIM_TX_UIPS_CLK_SHIFT (1) +#define DSIM_TX_UIPS_CLK_EXIT_SHIFT (0) + +/* S5P_DSIM_MDRESOL */ +#define DSIM_MAIN_STAND_BY (1<< 31) +#define DSIM_MAIN_NOT_READY (0<< 31) +#define DSIM_MAIN_VRESOL (x) (((x)& 0x7ff)<< 16)arch/arm/plat-s5p/include/plat/regs-dsim.h line 166
Quoted 10 lines
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +10
-0+#define DSIM_MAIN_HRESOL (x) (((x)& 0X7ff)<< 0) + +/* S5P_DSIM_MVPORCH */ +#define DSIM_CMD_ALLOW_SHIFT (28) +#define DSIM_STABLE_VFP_SHIFT (16) +#define DSIM_MAIN_VBP_SHIFT (0) +#define DSIM_CMD_ALLOW_MASK (0xf<< DSIM_CMD_ALLOW_SHIFT) +#define DSIM_STABLE_VFP_MASK (0x7ff<< DSIM_STABLE_VFP_SHIFT) +#define DSIM_MAIN_VBP_MASK (0x7ff<< DSIM_MAIN_VBP_SHIFT) +#define DSIM_CMD_ALLOW (x) (((x)& 0xf)<<
DSIM_CMD_ALLOW_SHIFT)arch/arm/plat-s5p/include/plat/regs-dsim.h line 167
Quoted 1 line
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +1
-0+#define DSIM_STABLE_VFP (x) (((x)& 0x7ff)<<
DSIM_STABLE_VFP_SHIFT)arch/arm/plat-s5p/include/plat/regs-dsim.h line 168
Quoted 1 line
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +1
-0+#define DSIM_MAIN_VBP (x) (((x)& 0x7ff)<<
DSIM_MAIN_VBP_SHIFT)arch/arm/plat-s5p/include/plat/regs-dsim.h
Quoted 7 lines
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +7
-0+ +/* S5P_DSIM_MHPORCH */ +#define DSIM_MAIN_HFP_SHIFT (16) +#define DSIM_MAIN_HBP_SHIFT (0) +#define DSIM_MAIN_HFP_MASK ((0xffff)<< DSIM_MAIN_HFP_SHIFT) +#define DSIM_MAIN_HBP_MASK ((0xffff)<< DSIM_MAIN_HBP_SHIFT) +#define DSIM_MAIN_HFP (x) (((x)& 0xffff)<<
DSIM_MAIN_HFP_SHIFT)arch/arm/plat-s5p/include/plat/regs-dsim.h line 176
Quoted 1 line
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +1
-0+#define DSIM_MAIN_HBP (x) (((x)& 0xffff)<<
DSIM_MAIN_HBP_SHIFT)arch/arm/plat-s5p/include/plat/regs-dsim.h
Quoted 7 lines
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +7
-0+ +/* S5P_DSIM_MSYNC */ +#define DSIM_MAIN_VSA_SHIFT (22) +#define DSIM_MAIN_HSA_SHIFT (0) +#define DSIM_MAIN_VSA_MASK ((0x3ff)<< DSIM_MAIN_VSA_SHIFT) +#define DSIM_MAIN_HSA_MASK ((0xffff)<< DSIM_MAIN_HSA_SHIFT) +#define DSIM_MAIN_VSA (x) (((x)& 0x3ff)<<
DSIM_MAIN_VSA_SHIFT)arch/arm/plat-s5p/include/plat/regs-dsim.h line 184
Quoted 1 line
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +1
-0+#define DSIM_MAIN_HSA (x) (((x)& 0xffff)<<
DSIM_MAIN_HSA_SHIFT)arch/arm/plat-s5p/include/plat/regs-dsim.h line 195
Quoted 11 lines
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +11
-0+ +/* S5P_DSIM_SDRESOL */ +#define DSIM_SUB_STANDY_SHIFT (31) +#define DSIM_SUB_VRESOL_SHIFT (16) +#define DSIM_SUB_HRESOL_SHIFT (0) +#define DSIM_SUB_STANDY_MASK ((0x1)<< DSIM_SUB_STANDY_SHIFT) +#define DSIM_SUB_VRESOL_MASK ((0x7ff)<< DSIM_SUB_VRESOL_SHIFT) +#define DSIM_SUB_HRESOL_MASK ((0x7ff)<< DSIM_SUB_HRESOL_SHIFT) +#define DSIM_SUB_STANDY (1<< DSIM_SUB_STANDY_SHIFT) +#define DSIM_SUB_NOT_READY (0<< DSIM_SUB_STANDY_SHIFT) +#define DSIM_SUB_VRESOL (x) (((x)& 0x7ff)<<
DSIM_SUB_VRESOL_SHIFT)arch/arm/plat-s5p/include/plat/regs-dsim.h line 196
Quoted 1 line
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +1
-0+#define DSIM_SUB_HRESOL (x) (((x)& 0x7ff)<<
DSIM_SUB_HRESOL_SHIFT)Quoted 73 lines
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +73
-0+ +/* S5P_DSIM_INTSRC */ +#define INTSRC_ERR_CONTENT_LP1 (1<< 0) +#define INTSRC_ERR_CONTENT_LP0 (1<< 1) +#define INTSRC_ERR_CONTROL0 (1<< 2) +#define INTSRC_ERR_CONTROL1 (1<< 3) +#define INTSRC_ERR_CONTROL2 (1<< 4) +#define INTSRC_ERR_CONTROL3 (1<< 5) +#define INTSRC_ERR_SYNC0 (1<< 6) +#define INTSRC_ERR_SYNC1 (1<< 7) +#define INTSRC_ERR_SYNC2 (1<< 8) +#define INTSRC_ERR_SYNC3 (1<< 9) +#define INTSRC_ERR_ESC0 (1<< 10) +#define INTSRC_ERR_ESC1 (1<< 11) +#define INTSRC_ERR_ESC2 (1<< 12) +#define INTSRC_ERR_ESC3 (1<< 13) +#define INTSRC_ERR_RX_CRC (1<< 14) +#define INTSRC_ERR_RX_ECC (1<< 15) +#define INTSRC_RX_ACK (1<< 16) +#define INTSRC_RX_TE (1<< 17) +#define INTSRC_RX_DAT_DONE (1<< 18) +#define INTSRC_TA_TOUT (1<< 20) +#define INTSRC_LPDR_TOUT (1<< 21) +#define INTSRC_FRAME_DONE (1<< 24) +#define INTSRC_BUS_TURN_OVER (1<< 25) +#define INTSRC_SYNC_OVERRIDE (1<< 28) +#define INTSRC_SFR_FIFO_EMPTY (1<< 29) +#define INTSRC_SW_RST_RELEASE (1<< 30) +#define INTSRC_PLL_STABLE (1<< 31) + +/* S5P_DSIM_INTMSK */ +#define INTMSK_ERR_CONTENT_LP1 (1<< 0) +#define INTMSK_ERR_CONTENT_LP0 (1<< 1) +#define INTMSK_ERR_CONTROL0 (1<< 2) +#define INTMSK_ERR_CONTROL1 (1<< 3) +#define INTMSK_ERR_CONTROL2 (1<< 4) +#define INTMSK_ERR_CONTROL3 (1<< 5) +#define INTMSK_ERR_SYNC0 (1<< 6) +#define INTMSK_ERR_SYNC1 (1<< 7) +#define INTMSK_ERR_SYNC2 (1<< 8) +#define INTMSK_ERR_SYNC3 (1<< 9) +#define INTMSK_ERR_ESC0 (1<< 10) +#define INTMSK_ERR_ESC1 (1<< 11) +#define INTMSK_ERR_ESC2 (1<< 12) +#define INTMSK_ERR_ESC3 (1<< 13) +#define INTMSK_ERR_RX_CRC (1<< 14) +#define INTMSK_ERR_RX_ECC (1<< 15) +#define INTMSK_RX_ACK (1<< 16) +#define INTMSK_RX_TE (1<< 17) +#define INTMSK_RX_DAT_DONE (1<< 18) +#define INTMSK_TA_TOUT (1<< 20) +#define INTMSK_LPDR_TOUT (1<< 21) +#define INTMSK_FRAME_DONE (1<< 24) +#define INTMSK_BUS_TURN_OVER (1<< 25) +#define INTMSK_SFR_FIFO_EMPTY (1<< 29) +#define INTMSK_SW_RST_RELEASE (1<< 30) +#define INTMSK_PLL_STABLE (1<< 31) + +/* S5P_DSIM_PKTHDR */ +#define DSIM_PACKET_HEADER_DI (x) (((x)& 0xff)<< 0) +/* Word count lower byte for long packet */ +#define DSIM_PACKET_HEADER_DAT0 (x) (((x)& 0xff)<< 8) +/* Word count upper byte for long packet */ +#define DSIM_PACKET_HEADER_DAT1 (x) (((x)& 0xff)<< 16) + +/* S5P_DSIM_FIFOCTRL */ +#define DSIM_RX_FIFO (1<< 4) +#define DSIM_TX_SFR_FIFO (1<< 3) +#define DSIM_I80_FIFO (1<< 2) +#define DSIM_SUB_DISP_FIFO (1<< 1) +#define DSIM_MAIN_DISP_FIFO (1<< 0) + +/* S5P_DSIM_PHYACCHR */ arch/arm/plat-s5p/include/plat/regs-dsim.h line 279
Quoted 10 lines
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +10
-0+#define DSIM_AFC_CTL (x) (((x)& 0x7)<< 5) +#define DSIM_AFC_ENABLE (1<< 14) +#define DSIM_AFC_DISABLE (0<< 14) + +/* S5P_DSIM_PLLCTRL */ +#define DSIM_PMS_SHIFT (1) +#define DSIM_PLL_EN_SHIFT (23) +#define DSIM_FREQ_BAND_SHIFT (24) +#define DSIM_PMS (x) (((x)& 0x7ffff)<< DSIM_PMS_SHIFT) +#define DSIM_FREQ_BAND (x) (((x)& 0xf)<<
DSIM_FREQ_BAND_SHIFT)
Quoted 11 lines
arch/arm/plat-s5p/include/plat/regs-dsim.h line 281
Quoted 2 lines
arch/arm/plat-s5p/include/plat/regs-dsim.h new file +2
-0+ +#endif /* _REGS_DSIM_H */ All these registers' definitions seem to be referenced only from one driver in
drivers/video/s5p_dsim*.c. How about creating s5p-dsim directory indrivers/video/and moving this whole pile of definitions there?
Also please see this thread
http://www.mail-archive.com/linux-media at vger.kernel.org/msg21129.html for more insight.
Ok, I agree to your opinion.
I will move this definition file to driver path.
Quoted 88 lines
drivers/video/Kconfig config FB_S3C2410_DEBUG · line 1996
Quoted 6 lines
drivers/video/Kconfig +0
-0@@ -1996,6 +1996,13 @@ config FB_S3C2410_DEBUG Turn on debugging messages. Note that you can set/unset at runtime
Quoted 70 lines
drivers/video/Kconfig +7
-0through sysfs +config S5P_MIPI_DSI + tristate "Samsung SoC MIPI-DSI support." + depends on FB_S3C&& ARCH_S5PV210 + default n + help + This enables support for MIPI-DSI device for samsung SoC S5PV210. + config FB_NUC900 bool "NUC900 LCD framebuffer support" depends on FB&& ARCH_W90X900drivers/video/Makefile +2
-0@@ -115,6 +115,8 @@ obj-$(CONFIG_FB_SH7760) += sh7760fb.o obj-$(CONFIG_FB_IMX) += imxfb.o obj-$(CONFIG_FB_S3C) += s3c-fb.o obj-$(CONFIG_FB_S3C2410) += s3c2410fb.o +obj-$(CONFIG_S5P_MIPI_DSI) += s5p-dsim.o s5p_dsim_common.o \ + s5p_dsim_lowlevel.o obj-$(CONFIG_FB_FSL_DIU) += fsl-diu-fb.o obj-$(CONFIG_FB_COBALT) += cobalt_lcdfb.o obj-$(CONFIG_FB_PNX4008_DUM) += pnx4008/drivers/video/s5p-dsim.c new file +39
-0@@ -0,0 +1,463 @@ +/* linux/drivers/video/s5p-dsim.c +* +* Samsung MIPI-DSIM driver. +* +* InKi Dae,<[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +*/ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/errno.h> +#include <linux/clk.h> +#include <linux/mutex.h> +#include <linux/wait.h> +#include <linux/fs.h> +#include <linux/mm.h> +#include <linux/fb.h> +#include <linux/ctype.h> +#include <linux/platform_device.h> +#include <linux/io.h> +#include <linux/irq.h> +#include <linux/memory.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/kthread.h> +#include <linux/regulator/consumer.h> +#include <linux/notifier.h> + +#include <plat/fb.h> +#include <plat/regs-dsim.h> +#include <plat/dsim.h> +#include <plat/mipi_ddi.h> + +#include <mach/map.h> + +#include "s5p_dsim_common.h" drivers/video/s5p-dsim.c line 49
Quoted 10 lines
drivers/video/s5p-dsim.c new file +10
-0+ +struct mipi_lcd_info { +struct list_head list; +struct mipi_lcd_driver *mipi_drv; +}; + +static LIST_HEAD (lcd_info_list); +static DEFINE_MUTEX (mipi_lock); + +struct dsim_global dsim;
Quoted 9 lines
Using a global variable like this seems rather hacky.. The driver will not be usable when there are more than one instance of the s5p-dsim device in the system. Or is it impossible that there could be multiple entities of MIPI-DSIM in the SoC?
How about allocating an instance of structdsim_global(and perhaps changing it's name since it's not global any more?..) during device probing and storing a pointer to it in driver's private data in struct device/platform_device? Isn't that doable?
Your saying makes sense but mipi-dsi driver would have only one instance.
Quoted 83 lines
Regards,
SylwesterQuoted 35 lines
drivers/video/s5p-dsim.c new file +35
-0+ +struct s5p_platform_dsim *to_dsim_plat (struct device *dev) +{ +struct platform_device *pdev =to_platform_device (dev); + +return (struct s5p_platform_dsim *)pdev->dev.platform_data; +} + +/* +* notifier callback function for fb_blank +* - this function would be called by device specific fb_blank. +*/ +static int s5p_dsim_notifier_callback (struct notifier_block *self, +unsigned long event,void *data) +{ +switch (event) { +case FB_BLANK_UNBLANK : +case FB_BLANK_NORMAL : +if (dsim.pd->mipi_power) + dsim.pd->mipi_power (&dsim, dsim.r_mipi_1_1v, + dsim.r_mipi_1_8v,1 ); + +clk_enable (dsim.clock); + +if (dsim.mipi_drv->resume) + dsim.mipi_drv->resume (dsim.dev); + +s5p_dsim_init_dsim (&dsim); +s5p_dsim_init_link (&dsim); + +s5p_dsim_set_hs_enable (&dsim); +s5p_dsim_set_data_transfer_mode (&dsim, +DSIM_TRANSFER_BYCPU ,1 ); + +/* it needs delay for stabilization */ drivers/video/s5p-dsim.c
Quoted 10 lines
drivers/video/s5p-dsim.c new file +10
-0+mdelay (dsim.pd->delay_for_stabilization); + +if (dsim.mipi_drv->init) + dsim.mipi_drv->init (dsim.dev); +else +dev_warn (dsim.dev,"init func is null.\n" ); + +s5p_dsim_set_display_mode (&dsim, dsim.dsim_lcd_info,NULL ); + + s5p_dsim_set_data_transfer_mode(&dsim, DSIM_TRANSFER_BYLCDC,1);
Quoted 16 lines
drivers/video/s5p-dsim.c new file +16
-0+ dsim.mipi_ddi_pd->resume_complete =1 ; + +dev_dbg (dsim.dev,"FB_BLANK_NORMAL or UNBLANK.\n" ); + +break ; +case FB_BLANK_POWERDOWN : + dsim.mipi_ddi_pd->resume_complete =0 ; + +if (dsim.mipi_drv->suspend) + dsim.mipi_drv->suspend (dsim.dev); + +clk_disable (dsim.clock); + +if (dsim.pd->mipi_power) + dsim.pd->mipi_power (&dsim, dsim.r_mipi_1_1v, + dsim.r_mipi_1_8v,0 );drivers/video/s5p-dsim.c line 120
Quoted 10 lines
drivers/video/s5p-dsim.c new file +10
-0+ +dev_dbg (dsim.dev,"FB_BLANK_POWERDOWN.\n" ); +break ; +default : +dev_warn (dsim.dev,"unknown FB_BLANK command.\n" ); +break ; + } + +return 0 ; +}<snip>
--
Regards,
Sylwester