Skip to contentSkip to conversation

OMAP: ZOOM2: Change GPIO to enable LCD NEC NL8048HL11-01B on OMAP34x-II MDP

PATCH New Omar Ramirez Luna 2 participants 3 messages Nov 24, 2010 – Nov 30, 2010

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 OMAP: ZOOM2: Change GPIO to enable LCD NEC NL8048HL11-01B on OMAP34x-II MDP

From: Yanick Saugy <[email protected]>

The PIN which controls LCD's reset signal (VGA_nRESET/h_GPIO_96) was not configured as a GPIO. We had to modify the OMAP MUX, and select this PIN (CAM_XCLKA) as an output GPIO (OMAP_MUX_MODE4). (kernel 2.6.35)

Be aware of changing this PIN will probably disable the camera, because it was previously configured as a camera clock.

---

I'm not sure if this patch was forgotten, hence resending. Without it, a blanks screen is seen on zoom2 board.

Original patch:
http://patchwork.kernel.org/patch/196922/

 arch/arm/mach-omap2/board-zoom2.c |    2 ++
 1 files changed, 2 insertions(+), 0 deletions(-)
arch/arm/mach-omap2/board-zoom2.c +2 -0
index 1cd6414..8fe578c 100644
@@ -51,6 +51,8 @@ static struct omap_board_mux board_mux[] __initdata = {
 	OMAP3_MUX(ETK_D4, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP),
 	OMAP3_MUX(ETK_D5, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP),
 	OMAP3_MUX(ETK_D6, OMAP_MUX_MODE2 | OMAP_PIN_INPUT_PULLUP),
+	/* LCD Panel reset (PROD) - GPIO 96 */
+	OMAP3_MUX(CAM_XCLKA, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 #else
Signature · 1 line
1.7.1
#1 lore raw

PATCH 1/1 OMAP: ZOOM2: Change GPIO to enable LCD NEC NL8048HL11-01B on OMAP34x-II MDP

Hi,

Quoted 9 lines · ext Omar Ramirez Luna

From: Yanick Saugy <[email protected]>

The PIN which controls LCD's reset signal (VGA_nRESET/h_GPIO_96) was not configured as a GPIO. We had to modify the OMAP MUX, and select this PIN (CAM_XCLKA) as an output GPIO (OMAP_MUX_MODE4). (kernel 2.6.35)

Be aware of changing this PIN will probably disable the camera, because it was previously configured as a camera clock.

Quoted 7 lines

---

I'm not sure if this patch was forgotten, hence resending. Without it, a blanks screen is seen on zoom2 board.

Yes, I seem to have missed this.

But I'm a bit confused. You say that this will disable camera. Is there a camera connected to the board, and it won't work after this?

Tomi

#2 lore raw

PATCH 1/1 OMAP: ZOOM2: Change GPIO to enable LCD NEC NL8048HL11-01B on OMAP34x-II MDP

Quoted 17 lines · Tomi Valkeinen

Hi,

Quoted 14 lines · ext Omar Ramirez Luna

From: Yanick Saugy <[email protected]>

The PIN which controls LCD's reset signal (VGA_nRESET/h_GPIO_96) was not configured as a GPIO. We had to modify the OMAP MUX, and select this PIN (CAM_XCLKA) as an output GPIO (OMAP_MUX_MODE4). (kernel 2.6.35)

Be aware of changing this PIN will probably disable the camera, because it was previously configured as a camera clock.

---

Quoted 7 lines
Quoted 2 lines

I'm not sure if this patch was forgotten, hence resending. Without it, a blanks screen is seen on zoom2 board.

Yes, I seem to have missed this.

But I'm a bit confused. You say that this will disable camera. Is there a camera connected to the board, and it won't work after this?

I'm not quite familiar with the camera, but will try to check it (might take some time).

Yes, there is a camera module connected to zoom2 board, but I don't know for sure if both share this pin (which at least from author's comment and existing code appears to be the case).

Regards,

Omar