Skip to contentSkip to conversation

serial: omap-serial: Add support for kernel debugger

PATCH In review Cosmin Cojocar 2 participants 6 messages Nov 22, 2010 – Dec 5, 2010

lore
Share & tools
lore
#0 lore raw

PATCH v3 1/1 serial: omap-serial: Add support for kernel debugger

The kgdb invokes the poll_put_char and poll_get_char when communicating with the host. This patch also changes the initialization order because the kgdb will check at the very beginning, if there is a valid serial driver.

---
 drivers/serial/Makefile      |    2 +-
 drivers/serial/omap-serial.c |   38 ++++++++++++++++++++++++++++++++------
 2 files changed, 33 insertions(+), 7 deletions(-)
drivers/serial/Makefile +1 -1
index c570576..ad86113 100644
@@ -80,6 +80,7 @@ obj-$(CONFIG_SERIAL_NETX) += netx-serial.o
 obj-$(CONFIG_SERIAL_OF_PLATFORM) += of_serial.o
 obj-$(CONFIG_SERIAL_OF_PLATFORM_NWPSERIAL) += nwpserial.o
 obj-$(CONFIG_SERIAL_KS8695) += serial_ks8695.o
+obj-$(CONFIG_SERIAL_OMAP) += omap-serial.o
 obj-$(CONFIG_KGDB_SERIAL_CONSOLE) += kgdboc.o
 obj-$(CONFIG_SERIAL_QE) += ucc_uart.o
 obj-$(CONFIG_SERIAL_TIMBERDALE)	+= timbuart.o
@@ -88,4 +89,3 @@ obj-$(CONFIG_SERIAL_ALTERA_JTAGUART) += altera_jtaguart.o
 obj-$(CONFIG_SERIAL_ALTERA_UART) += altera_uart.o
 obj-$(CONFIG_SERIAL_MRST_MAX3110)	+= mrst_max3110.o
 obj-$(CONFIG_SERIAL_MFD_HSU)	+= mfd.o
-obj-$(CONFIG_SERIAL_OMAP) += omap-serial.o
drivers/serial/omap-serial.c +32 -6
index 03a96db..552759e 100644
@@ -866,12 +866,6 @@ serial_omap_type(struct uart_port *port)
 	return up->name;
 }
 
-#ifdef CONFIG_SERIAL_OMAP_CONSOLE
-
-static struct uart_omap_port *serial_omap_console_ports[4];
-
-static struct uart_driver serial_omap_reg;
-
 #define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
 
 static inline void wait_for_xmitr(struct uart_omap_port *up)
@@ -905,6 +899,34 @@ static inline void wait_for_xmitr(struct uart_omap_port *up)
 	}
 }
 
+#ifdef CONFIG_CONSOLE_POLL
+
+static void serial_omap_poll_put_char(struct uart_port *port, unsigned char ch)
+{
+	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	wait_for_xmitr(up);
+	serial_out(up, UART_TX, ch);
+}
+
+static int serial_omap_poll_get_char(struct uart_port *port)
+{
+	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	unsigned int status = serial_in(up, UART_LSR);
+
+	if (!(status & UART_LSR_DR))
+		return NO_POLL_CHAR;
+
+	return serial_in(up, UART_RX);
+}
+
+#endif /* CONFIG_CONSOLE_POLL */
+
+#ifdef CONFIG_SERIAL_OMAP_CONSOLE
+
+static struct uart_omap_port *serial_omap_console_ports[4];
+
+static struct uart_driver serial_omap_reg;
+
 static void serial_omap_console_putchar(struct uart_port *port, int ch)
 {
 	struct uart_omap_port *up = (struct uart_omap_port *)port;
@@ -1022,6 +1044,10 @@ static struct uart_ops serial_omap_pops = {
 	.request_port	= serial_omap_request_port,
 	.config_port	= serial_omap_config_port,
 	.verify_port	= serial_omap_verify_port,
+#ifdef CONFIG_CONSOLE_POLL
+	.poll_put_char  = serial_omap_poll_put_char,
+	.poll_get_char  = serial_omap_poll_get_char,
+#endif
 };
 
 static struct uart_driver serial_omap_reg = {
Signature · 1 line
1.6.3.3
#1 lore raw
Quoted 4 lines · Cosmin Cojocar

The kgdb invokes the poll_put_char and poll_get_char when communicating with the host. This patch also changes the initialization order because the kgdb will check at the very beginning, if there is a valid serial driver.

What was the difference between v2 and v3?

#2 lore raw

The v2 was a intermediate testing version which I sent it out by mistake. The difference between the tow is that the v2 uses a infinite loop to wait for data to be transfered out form buffer, whereas the v3 relies on existing wait_form_xmitr function.

Regards,
Cosmin

Quoted 8 lines · Greg KH
Quoted 4 lines · Cosmin Cojocar

The kgdb invokes the poll_put_char and poll_get_char when communicating with the host. This patch also changes the initialization order because the kgdb will check at the very beginning, if there is a valid serial driver.

What was the difference between v2 and v3?

#3 lore raw

A: No.
Q: Should I include quotations after my reply?

http://daringfireball.net/2007/07/on_top

Quoted 4 lines · Cosmin Cojocar

The v2 was a intermediate testing version which I sent it out by mistake. The difference between the tow is that the v2 uses a infinite loop to wait for data to be transfered out form buffer, whereas the v3 relies on existing wait_form_xmitr function.

In the future, please say this in the comment section in the patch (i.e. below the "---" line.)

thanks,

greg k-h

#4 lore raw
In reply to Cosmin Cojocar
Quoted 8 lines · Cosmin Cojocar

The kgdb invokes the poll_put_char and poll_get_char when communicating with the host. This patch also changes the initialization order because the kgdb will check at the very beginning, if there is a valid serial driver.

---
 drivers/serial/Makefile      |    2 +-

This fails to apply to the linux-next tree due to Makefile changes in this area. Can you rediff it and resend it to me so that I can apply it?

thanks,

greg k-h

#5 lore raw

PATCH v3 1/1 serial: omap-serial: Add support for kernel debugger

The kgdb invokes the poll_put_char and poll_get_char when communicating with the host. This patch also changes the initialization order because the kgdb will check at the very beginning, if there is a valid serial driver.

---

I fixed the conflicts from Makefile when applying it to the linux-next tree. This patch is against the linux-next tree.

 drivers/serial/Makefile      |    2 +-
 drivers/serial/omap-serial.c |   38 ++++++++++++++++++++++++++++++++------
 2 files changed, 33 insertions(+), 7 deletions(-)
drivers/serial/Makefile +1 -1
index f9b26df..8ea92e9 100644
@@ -80,6 +80,7 @@ obj-$(CONFIG_SERIAL_NETX) += netx-serial.o
 obj-$(CONFIG_SERIAL_OF_PLATFORM) += of_serial.o
 obj-$(CONFIG_SERIAL_OF_PLATFORM_NWPSERIAL) += nwpserial.o
 obj-$(CONFIG_SERIAL_KS8695) += serial_ks8695.o
+obj-$(CONFIG_SERIAL_OMAP) += omap-serial.o
 obj-$(CONFIG_KGDB_SERIAL_CONSOLE) += kgdboc.o
 obj-$(CONFIG_SERIAL_QE) += ucc_uart.o
 obj-$(CONFIG_SERIAL_TIMBERDALE)	+= timbuart.o
@@ -89,6 +90,5 @@ obj-$(CONFIG_SERIAL_ALTERA_UART) += altera_uart.o
 obj-$(CONFIG_SERIAL_VT8500) += vt8500_serial.o
 obj-$(CONFIG_SERIAL_MRST_MAX3110)	+= mrst_max3110.o
 obj-$(CONFIG_SERIAL_MFD_HSU)	+= mfd.o
-obj-$(CONFIG_SERIAL_OMAP) += omap-serial.o
 obj-$(CONFIG_SERIAL_IFX6X60)  	+= ifx6x60.o
 obj-$(CONFIG_SERIAL_PCH_UART)	+= pch_uart.o
drivers/serial/omap-serial.c +32 -6
index 1201eff..7f2f010 100644
@@ -866,12 +866,6 @@ serial_omap_type(struct uart_port *port)
 	return up->name;
 }
 
-#ifdef CONFIG_SERIAL_OMAP_CONSOLE
-
-static struct uart_omap_port *serial_omap_console_ports[4];
-
-static struct uart_driver serial_omap_reg;
-
 #define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
 
 static inline void wait_for_xmitr(struct uart_omap_port *up)
@@ -905,6 +899,34 @@ static inline void wait_for_xmitr(struct uart_omap_port *up)
 	}
 }
 
+#ifdef CONFIG_CONSOLE_POLL
+
+static void serial_omap_poll_put_char(struct uart_port *port, unsigned char ch)
+{
+	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	wait_for_xmitr(up);
+	serial_out(up, UART_TX, ch);
+}
+
+static int serial_omap_poll_get_char(struct uart_port *port)
+{
+	struct uart_omap_port *up = (struct uart_omap_port *)port;
+	unsigned int status = serial_in(up, UART_LSR);
+
+	if (!(status & UART_LSR_DR))
+		return NO_POLL_CHAR;
+
+	return serial_in(up, UART_RX);
+}
+
+#endif /* CONFIG_CONSOLE_POLL */
+
+#ifdef CONFIG_SERIAL_OMAP_CONSOLE
+
+static struct uart_omap_port *serial_omap_console_ports[4];
+
+static struct uart_driver serial_omap_reg;
+
 static void serial_omap_console_putchar(struct uart_port *port, int ch)
 {
 	struct uart_omap_port *up = (struct uart_omap_port *)port;
@@ -1022,6 +1044,10 @@ static struct uart_ops serial_omap_pops = {
 	.request_port	= serial_omap_request_port,
 	.config_port	= serial_omap_config_port,
 	.verify_port	= serial_omap_verify_port,
+#ifdef CONFIG_CONSOLE_POLL
+	.poll_put_char  = serial_omap_poll_put_char,
+	.poll_get_char  = serial_omap_poll_get_char,
+#endif
 };
 
 static struct uart_driver serial_omap_reg = {
Signature · 1 line
1.6.3.3