MSM: Add USB suport for QSD8x50
Subsystems (3)
PATCH 1/2 MSM: Add USB suport for QSD8x50
OTG driver takes care of putting hardware into low power mode. Hence make peripheral and host devices as children of OTG device and let runtime PM takes care of notifying peripheral and host state to OTG device. VBUS power up and shutdown routines are implemented by modem processor. As RPC infrastructure is not available, configure USB in peripheral only mode.
---
This patch depends on [PATCH V3 00/11] Add MSM USB controller driver patch series which is under review.
arch/arm/mach-msm/board-qsd8x50.c | 19 +++++++++ arch/arm/mach-msm/devices-qsd8x50.c | 71 +++++++++++++++++++++++++++++++++++ arch/arm/mach-msm/devices.h | 2 + 3 files changed, 92 insertions(+), 0 deletions(-)
arch/arm/mach-msm/board-qsd8x50.c +19 -0
@@ -20,6 +20,7 @@#include <linux/gpio.h> #include <linux/platform_device.h> #include <linux/delay.h> +#include <linux/usb/msm_hsusb.h> #include <asm/mach-types.h> #include <asm/mach/arch.h>
@@ -74,9 +75,24 @@ static int __init msm_init_smc91x(void) }module_init (msm_init_smc91x); +static int hsusb_phy_init_seq[] = { +0x08 ,0x31 ,/* Increase HS Driver Amplitude */ +0x20 ,0x32 ,/* Enable and set Pre-Emphasis Depth to 10% */ +-1 +}; + +static struct msm_otg_platform_data msm_otg_pdata = { + .phy_init_seq = hsusb_phy_init_seq, + .mode =USB_PERIPHERAL , + .otg_control =OTG_PHY_CONTROL , +}; +static struct platform_device *devices[]__initdata = { &msm_device_uart3, &msm_device_smd, + &msm_device_otg, + &msm_device_hsusb, + &msm_device_hsusb_host, };static void __init qsd8x50_map_io (void )
@@ -93,6 +109,9 @@ static void __init qsd8x50_init_irq(void)static void __init qsd8x50_init (void ) { + msm_device_otg.dev.platform_data = &msm_otg_pdata; + msm_device_hsusb.dev.parent = &msm_device_otg.dev; + msm_device_hsusb_host.dev.parent = &msm_device_otg.dev;platform_add_devices (devices,ARRAY_SIZE (devices)); }
arch/arm/mach-msm/devices-qsd8x50.c +71 -0
77 lines not on this page · raw message
arch/arm/mach-msm/devices.h +2 -0
@@ -28,6 +28,8 @@ extern struct platform_device msm_device_sdc3;extern struct platform_device msm_device_sdc4;extern struct platform_device msm_device_hsusb; +extern struct platform_device msm_device_otg; +extern struct platform_device msm_device_hsusb_host;extern struct platform_device msm_device_i2c;
Signature · 5 lines
1.7.1 -- Sent by a consultant of the Qualcomm Innovation Center, Inc. The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
PATCH 2/2 MSM: Add USB support for MSM7x30
Add USB OTG, peripheral and host devices. This patch also adds usb_phy_clk which is required for resetting the PHY. VBUS power up and shutdown routines depends on PMIC module. As PMIC driver is unavailable, configure USB in peripheral only mode.
---
This patch depends on [PATCH V3 00/11] Add MSM USB controller driver patch series which is under review.
arch/arm/mach-msm/board-msm7x30.c | 20 ++++++ arch/arm/mach-msm/devices-msm7x30.c | 72 +++++++++++++++++++++++ arch/arm/mach-msm/include/mach/msm_iomap-7x30.h | 3 + 3 files changed, 95 insertions(+), 0 deletions(-)
arch/arm/mach-msm/board-msm7x30.c +20 -0
@@ -22,6 +22,7 @@#include <linux/delay.h> #include <linux/io.h> #include <linux/smsc911x.h> +#include <linux/usb/msm_hsusb.h> #include <asm/mach-types.h> #include <asm/mach/arch.h>
@@ -39,11 +40,26 @@extern struct sys_timer msm_timer; +static int hsusb_phy_init_seq[] = { +0x30 ,0x32 ,/* Enable and set Pre-Emphasis Depth to 20% */ +0x02 ,0x36 ,/* Disable CDR Auto Reset feature */ +-1 +}; + +static struct msm_otg_platform_data msm_otg_pdata = { + .phy_init_seq = hsusb_phy_init_seq, + .mode =USB_PERIPHERAL , + .otg_control =OTG_PHY_CONTROL , +}; + static struct platform_device *devices[] __initdata = {#if defined(CONFIG_SERIAL_MSM ) || defined(CONFIG_MSM_SERIAL_DEBUGGER ) &msm_device_uart2, #endif &msm_device_smd, + &msm_device_otg, + &msm_device_hsusb, + &msm_device_hsusb_host, };static void __init msm7x30_init_irq (void )
@@ -53,6 +69,10 @@ static void __init msm7x30_init_irq(void)static void __init msm7x30_init (void ) { + msm_device_otg.dev.platform_data = &msm_otg_pdata; + msm_device_hsusb.dev.parent = &msm_device_otg.dev; + msm_device_hsusb_host.dev.parent = &msm_device_otg.dev; +platform_add_devices (devices,ARRAY_SIZE (devices)); }
arch/arm/mach-msm/devices-msm7x30.c +72 -0
84 lines not on this page · raw message
arch/arm/mach-msm/include/mach/msm_iomap-7x30.h +3 -0
@@ -119,4 +119,7 @@#define MSM_AD5_PHYS 0xA7000000#define MSM_AD5_SIZE (SZ_1M*13) +#define MSM_HSUSB_PHYS 0xA3600000 +#define MSM_HSUSB_SIZE SZ_1K +#endif
Signature · 5 lines
1.7.1 -- Sent by a consultant of the Qualcomm Innovation Center, Inc. The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
Hi Daniel,
Quoted 11 lines · Pavankumar Kondeti
OTG driver takes care of putting hardware into low power mode. Hence make peripheral and host devices as children of OTG device and let runtime PM takes care of notifying peripheral and host state to OTG device. VBUS power up and shutdown routines are implemented by modem processor. As RPC infrastructure is not available, configure USB in peripheral only mode.
Signed-off-by Pavankumar Kondeti <[email protected]>---
This patch depends on [PATCH V3 00/11] Add MSM USB controller driver patch series which is under review.
USB driver patches are taken into Greg KH usb-next tree. Is it possible to include this patch for 2.6.38?
Thanks,
Pavan
Signature · 2 lines
Sent by a consultant of the Qualcomm Innovation Center, Inc. The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
Quoted 1 line · Pavan Kondeti
Hi Daniel,
Are you talking to me? read below,
Quoted 8 lines · Pavankumar Kondeti
Quoted 7 lines
OTG driver takes care of putting hardware into low power mode. Hence make peripheral and host devices as children of OTG device and let runtime PM takes care of notifying peripheral and host state to OTG device. VBUS power up and shutdown routines are implemented by modem processor. As RPC infrastructure is not available, configure USB in peripheral only mode.
Quoted 7 lines
Quoted 4 lines
Signed-off-by Pavankumar Kondeti <[email protected]>---
This patch depends on [PATCH V3 00/11] Add MSM USB controller driver patch series which is under review.USB driver patches are taken into Greg KH usb-next tree. Is it possible to include this patch for 2.6.38?
I don't control Greg's tree, so I don't know what his policies are regarding patch acceptance ..
Daniel
Signature · 3 lines
Sent by an consultant of the Qualcomm Innovation Center, Inc. The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
Quoted 18 lines · Pavan Kondeti
Quoted 1 line
Hi Daniel,
Are you talking to me? read below,
Quoted 13 lines · Pavankumar Kondeti
Quoted 11 lines
OTG driver takes care of putting hardware into low power mode. Hence make peripheral and host devices as children of OTG device and let runtime PM takes care of notifying peripheral and host state to OTG device. VBUS power up and shutdown routines are implemented by modem processor. As RPC infrastructure is not available, configure USB in peripheral only mode.
Signed-off-by Pavankumar Kondeti <[email protected]>---
This patch depends on [PATCH V3 00/11] Add MSM USB controller driver patch series which is under review.
Quoted 6 lines
Quoted 2 lines
USB driver patches are taken into Greg KH usb-next tree. Is it possible to include this patch for 2.6.38?
I don't control Greg's tree, so I don't know what his policies are regarding patch acceptance ..
I am asking about board file changes. i.e this patch and the follow up patch not
USB driver patches.
Thanks,
Pavan
--
Sent by an consultant of the Qualcomm Innovation Center, Inc. The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
Quoted 18 lines · Daniel Walker
Quoted 1 line · Pavan Kondeti
Hi Daniel,
Are you talking to me? read below,
Quoted 13 lines · Pavankumar Kondeti
Quoted 11 lines
OTG driver takes care of putting hardware into low power mode. Hence make peripheral and host devices as children of OTG device and let runtime PM takes care of notifying peripheral and host state to OTG device. VBUS power up and shutdown routines are implemented by modem processor. As RPC infrastructure is not available, configure USB in peripheral only mode.
Signed-off-by Pavankumar Kondeti <[email protected]>---
This patch depends on [PATCH V3 00/11] Add MSM USB controller driver patch series which is under review.
Quoted 5 lines
Quoted 2 lines
USB driver patches are taken into Greg KH usb-next tree. Is it possible to include this patch for 2.6.38?
I don't control Greg's tree, so I don't know what his policies are regarding patch acceptance ..
They are like any other patch acceptance rules, what specifically is the issue here?
thanks,
greg k-h
Hi Greg,
Quoted 13 lines · Greg KH
Quoted 13 lines
Quoted 13 lines · Pavankumar Kondeti
Quoted 12 lines
Quoted 12 lines
Quoted 11 lines
Quoted 11 lines
OTG driver takes care of putting hardware into low power mode. Hence make peripheral and host devices as children of OTG device and let runtime PM takes care of notifying peripheral and host state to OTG device. VBUS power up and shutdown routines are implemented by modem processor. As RPC infrastructure is not available, configure USB in peripheral only mode.
Signed-off-by Pavankumar Kondeti <[email protected]>---
This patch depends on [PATCH V3 00/11] Add MSM USB controller driver patch series which is under review.
Quoted 7 lines
Quoted 5 lines
Quoted 5 lines
Quoted 2 lines
Quoted 2 lines
USB driver patches are taken into Greg KH usb-next tree. Is it possible to include this patch for 2.6.38?
I don't control Greg's tree, so I don't know what his policies are regarding patch acceptance ..
They are like any other patch acceptance rules, what specifically is the issue here?
The board support patches ( [PATCH 1/2] MSM: Add USB suport for QSD8x50) are dependent on USB OTG driver patches ([PATCH V3 00/11] Add MSM USB controller driver). The USB OTG driver patches are in your usb-next tree. Where should board support patches go? MSM tree/ USB tree?
Thanks in advance,
Pavan
Signature · 2 lines
Sent by a consultant of the Qualcomm Innovation Center, Inc. The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.
Quoted 21 lines · Pavan Kondeti
Hi Greg,
Quoted 18 lines · Greg KH
Quoted 18 lines
Quoted 18 lines · Pavankumar Kondeti
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
OTG driver takes care of putting hardware into low power mode. Hence make peripheral and host devices as children of OTG device and let runtime PM takes care of notifying peripheral and host state to OTG device. VBUS power up and shutdown routines are implemented by modem processor. As RPC infrastructure is not available, configure USB in peripheral only mode.
Quoted 7 lines
Quoted 7 lines
Quoted 4 lines
Quoted 4 lines
Signed-off-by Pavankumar Kondeti <[email protected]>---
This patch depends on [PATCH V3 00/11] Add MSM USB controller driver patch series which is under review.USB driver patches are taken into Greg KH usb-next tree. Is it possible to include this patch for 2.6.38?
I don't control Greg's tree, so I don't know what his policies are regarding patch acceptance ..
Quoted 7 lines
Quoted 2 lines
They are like any other patch acceptance rules, what specifically is the issue here?
The board support patches ( [PATCH 1/2] MSM: Add USB suport for QSD8x50) are dependent on USB OTG driver patches ([PATCH V3 00/11] Add MSM USB controller driver). The USB OTG driver patches are in your usb-next tree. Where should board support patches go? MSM tree/ USB tree?
MSM tree would make sense, right?
thanks,
greg k-h
Quoted 6 lines · Greg KH
Quoted 4 lines
The board support patches ( [PATCH 1/2] MSM: Add USB suport for QSD8x50) are dependent on USB OTG driver patches ([PATCH V3 00/11] Add MSM USB controller driver). The USB OTG driver patches are in your usb-next tree. Where should board support patches go? MSM tree/ USB tree?
MSM tree would make sense, right?
I'll include this in MSM.
David
Signature · 2 lines
Sent by an employee of the Qualcomm Innovation Center, Inc. The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum.