Skip to contentSkip to conversation

tnetv107x ssp drivers

PATCH In review Cyril Chemparathy 3 participants 14 messages Jan 17, 2011 – Jan 18, 2011 2 messages not in the archive

Subsystems (8)
lore
Share & tools
lore
#0 lore raw

v8 cover tnetv107x ssp drivers

TI's sequencer serial port (TI-SSP) is a jack-of-all-trades type of serial port device. It has a built-in programmable execution engine that can be programmed to operate as almost any serial bus (I2C, SPI, EasyScale, and others).

This patch series implements a driver stack that looks like the following:

                             +--------+
                             | eeprom | . . .
                             +--------+
   +-----------+             +--------------+ +---------+
   | regulator | . . .       |   i2c-gpio   | | 1-wire  | . . .
   +-----------+             +--------------+ +---------+
   +----------------------+  +--------------------------------+
   |       ssp-spi        |  |           ssp-gpio             |
   +----------------------+  +--------------------------------+
   +----------------------------------------------------------+
   |                            ssp                           |
   +----------------------------------------------------------+

Changes between v8 and v7 of this series:
- Reorder commits, removed regulator driver patch (already upstreamed)
- Renamed static function definitions to keep namespace clean (mfd, gpio)
- Removed instance pdata in mfd driver

Changes between v7 and v6 of this series:
- Workaround for iosel2 register not reading back set bits.
- Update backlight status once probe succeeds.

Changes between v6 and v5 of this series:
- Changed initcalls to module_init() across all drivers. This series now uses a late_initcall() in the board to delay initialization of gpio and regulator dependent devices.

Changes between v5 and v4 of this series:
- Moved drivers from misc/gpio/spi to mfd
- Removed implicit init-time iosel setup
- Minor cleanups in backlight driver

Changes between v3 and v4 of this series:
- Replaced polled wait for sequence termination with interrupt
- Improved locking within SSP driver
- Other minor cleanups

Changes between v2 and v3 of this series:
- Minor cleanups in Kconfig and Makefile ordering

Changes between v1 and v2 of this series:
- Replaced open()/close() semantics with dynamic platform_device registration on SSP probe.
- Removed user-land interface to regulator registers
- More sensible regulator constraints
- Other minor cleanups

Cyril Chemparathy (11):
mfd: add driver for sequencer serial port
spi: add ti-ssp spi master driver
gpio: add ti-ssp gpio driver
backlight: add support for tps6116x controller
davinci: add tnetv107x ssp platform device
davinci: add ssp config for tnetv107x evm board
davinci: add spi devices on tnetv107x evm
davinci: add tnetv107x evm regulators
davinci: add tnetv107x evm ti-ssp gpio device
davinci: add tnetv107x evm backlight device
davinci: add tnetv107x evm i2c eeprom device

 arch/arm/mach-davinci/board-tnetv107x-evm.c    |  197 ++++++++++
 arch/arm/mach-davinci/devices-tnetv107x.c      |   25 ++
 arch/arm/mach-davinci/include/mach/tnetv107x.h |    2 +
 arch/arm/mach-davinci/tnetv107x.c              |    2 +-
 drivers/gpio/Kconfig                           |   10 +
 drivers/gpio/Makefile                          |    1 +
 drivers/gpio/ti-ssp-gpio.c                     |  207 ++++++++++
 drivers/mfd/Kconfig                            |   11 +
 drivers/mfd/Makefile                           |    1 +
 drivers/mfd/ti-ssp.c                           |  476 ++++++++++++++++++++++++
 drivers/spi/Kconfig                            |   10 +
 drivers/spi/Makefile                           |    1 +
 drivers/spi/ti-ssp-spi.c                       |  402 ++++++++++++++++++++
 drivers/video/backlight/Kconfig                |    7 +
 drivers/video/backlight/Makefile               |    2 +-
 drivers/video/backlight/tps6116x.c             |  299 +++++++++++++++
 include/linux/mfd/ti_ssp.h                     |   97 +++++
 17 files changed, 1748 insertions(+), 2 deletions(-)
 create mode 100644 drivers/gpio/ti-ssp-gpio.c
 create mode 100644 drivers/mfd/ti-ssp.c
 create mode 100644 drivers/spi/ti-ssp-spi.c
 create mode 100644 drivers/video/backlight/tps6116x.c
 create mode 100644 include/linux/mfd/ti_ssp.h

A message that is not in the archive (sent off-list or not yet received): 1295291725-32509-1-git-send-email-cyril-l0cyMroinI0@public.gmane.org

#2 lore raw

PATCH v8 1/11 mfd: add driver for sequencer serial port

TI's sequencer serial port (TI-SSP) is a jack-of-all-trades type of serial port device. It has a built-in programmable execution engine that can be programmed to operate as almost any serial bus (I2C, SPI, EasyScale, and others).

This patch adds a driver for this controller device. The driver does not expose a user-land interface. Protocol drivers built on top of this layer are expected to remain in-kernel.

---
 drivers/mfd/Kconfig        |   11 +
 drivers/mfd/Makefile       |    1 +
 drivers/mfd/ti-ssp.c       |  476 ++++++++++++++++++++++++++++++++++++++++++++
 include/linux/mfd/ti_ssp.h |   87 ++++++++
 4 files changed, 575 insertions(+), 0 deletions(-)
 create mode 100644 drivers/mfd/ti-ssp.c
 create mode 100644 include/linux/mfd/ti_ssp.h
drivers/mfd/Kconfig +11 -0
index 3a1493b..a4b4b70 100644
@@ -81,6 +81,17 @@ config MFD_DM355EVM_MSP
 	  boards.  MSP430 firmware manages resets and power sequencing,
 	  inputs from buttons and the IR remote, LEDs, an RTC, and more.
 
+config MFD_TI_SSP
+	tristate "TI Sequencer Serial Port support"
+	depends on ARCH_DAVINCI_TNETV107X
+	select MFD_CORE
+	---help---
+	  Say Y here if you want support for the Sequencer Serial Port
+	  in a Texas Instruments TNETV107X SoC.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ti-ssp.
+
 config HTC_EGPIO
 	bool "HTC EGPIO support"
 	depends on GENERIC_HARDIRQS && GPIOLIB && ARM
drivers/mfd/Makefile +1 -0
index f54b365..f64cf13 100644
@@ -14,6 +14,7 @@ obj-$(CONFIG_HTC_I2CPLD)	+= htc-i2cpld.o
 
 obj-$(CONFIG_MFD_DAVINCI_VOICECODEC)	+= davinci_voicecodec.o
 obj-$(CONFIG_MFD_DM355EVM_MSP)	+= dm355evm_msp.o
+obj-$(CONFIG_MFD_TI_SSP)	+= ti-ssp.o
 
 obj-$(CONFIG_MFD_STMPE)		+= stmpe.o
 obj-$(CONFIG_MFD_TC35892)	+= tc35892.o
drivers/mfd/ti-ssp.c new file +476 -0

476 lines not on this page · raw message

include/linux/mfd/ti_ssp.h new file +87 -0

87 lines not on this page · raw message

Signature · 1 line
1.7.1
#3 lore raw

PATCH v8 2/11 spi: add ti-ssp spi master driver

In reply to a message not in the archive

This patch adds an SPI master implementation that operates on top of an underlying TI-SSP port.

---
 drivers/spi/Kconfig        |   10 +
 drivers/spi/Makefile       |    1 +
 drivers/spi/ti-ssp-spi.c   |  402 ++++++++++++++++++++++++++++++++++++++++++++
 include/linux/mfd/ti_ssp.h |    6 +
 4 files changed, 419 insertions(+), 0 deletions(-)
 create mode 100644 drivers/spi/ti-ssp-spi.c
drivers/spi/Kconfig +10 -0
index 78f9fd0..7f0ed2a 100644
@@ -336,6 +336,16 @@ config SPI_TEGRA
 	help
 	  SPI driver for NVidia Tegra SoCs
 
+config SPI_TI_SSP
+	tristate "TI Sequencer Serial Port - SPI Support"
+	depends on MFD_TI_SSP
+	help
+	  This selects an SPI master implementation using a TI sequencer
+	  serial port.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ti-ssp-spi.
+
 config SPI_TOPCLIFF_PCH
 	tristate "Topcliff PCH SPI Controller"
 	depends on PCI
drivers/spi/Makefile +1 -0
index 8bc1a5a..595e5b8 100644
@@ -40,6 +40,7 @@ obj-$(CONFIG_SPI_S3C24XX_GPIO)		+= spi_s3c24xx_gpio.o
 obj-$(CONFIG_SPI_S3C24XX)		+= spi_s3c24xx_hw.o
 obj-$(CONFIG_SPI_S3C64XX)		+= spi_s3c64xx.o
 obj-$(CONFIG_SPI_TEGRA)			+= spi_tegra.o
+obj-$(CONFIG_SPI_TI_SSP)		+= ti-ssp-spi.o
 obj-$(CONFIG_SPI_TOPCLIFF_PCH)		+= spi_topcliff_pch.o
 obj-$(CONFIG_SPI_TXX9)			+= spi_txx9.o
 obj-$(CONFIG_SPI_XILINX)		+= xilinx_spi.o
drivers/spi/ti-ssp-spi.c new file +402 -0

402 lines not on this page · raw message

include/linux/mfd/ti_ssp.h +6 -0
index 021fe09..dbb4b43 100644
@@ -32,6 +32,12 @@ struct ti_ssp_data {
 	struct ti_ssp_dev_data	dev_data[2];
 };
 
+struct ti_ssp_spi_data {
+	unsigned long	iosel;
+	int		num_cs;
+	void		(*select)(int cs);
+};
+
 /*
  * Sequencer port IO pin configuration bits.  These do not correlate 1-1 with
  * the hardware.  The iosel field in the port data combines iosel1 and iosel2,
Signature · 1 line
1.7.1

A message that is not in the archive (sent off-list or not yet received): 1295291725-32509-3-git-send-email-cyril-l0cyMroinI0@public.gmane.org

Acked-by
#5 lore raw

Re: [PATCH v8 02/11] spi: add ti-ssp spi master driver

Quoted 4 lines · Cyril Chemparathy

This patch adds an SPI master implementation that operates on top of an underlying TI-SSP port.

Quoted 480 lines
---
 drivers/spi/Kconfig        |   10 +
 drivers/spi/Makefile       |    1 +
 drivers/spi/ti-ssp-spi.c   |  402 ++++++++++++++++++++++++++++++++++++++++++++
 include/linux/mfd/ti_ssp.h |    6 +
 4 files changed, 419 insertions(+), 0 deletions(-)
 create mode 100644 drivers/spi/ti-ssp-spi.c
drivers/spi/Kconfig +10 -0
index 78f9fd0..7f0ed2a 100644
@@ -336,6 +336,16 @@ config SPI_TEGRA
 	help
 	  SPI driver for NVidia Tegra SoCs
 
+config SPI_TI_SSP
+	tristate "TI Sequencer Serial Port - SPI Support"
+	depends on MFD_TI_SSP
+	help
+	  This selects an SPI master implementation using a TI sequencer
+	  serial port.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ti-ssp-spi.
+
 config SPI_TOPCLIFF_PCH
 	tristate "Topcliff PCH SPI Controller"
 	depends on PCI
drivers/spi/Makefile +1 -0
index 8bc1a5a..595e5b8 100644
@@ -40,6 +40,7 @@ obj-$(CONFIG_SPI_S3C24XX_GPIO)		+= spi_s3c24xx_gpio.o
 obj-$(CONFIG_SPI_S3C24XX)		+= spi_s3c24xx_hw.o
 obj-$(CONFIG_SPI_S3C64XX)		+= spi_s3c64xx.o
 obj-$(CONFIG_SPI_TEGRA)			+= spi_tegra.o
+obj-$(CONFIG_SPI_TI_SSP)		+= ti-ssp-spi.o
 obj-$(CONFIG_SPI_TOPCLIFF_PCH)		+= spi_topcliff_pch.o
 obj-$(CONFIG_SPI_TXX9)			+= spi_txx9.o
 obj-$(CONFIG_SPI_XILINX)		+= xilinx_spi.o
drivers/spi/ti-ssp-spi.c new file +402 -0
new file mode 100644
index 0000000..ee22795
@@ -0,0 +1,402 @@
+/*
+ * Sequencer Serial Port (SSP) based SPI master driver
+ *
+ * Copyright (C) 2010 Texas Instruments Inc
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/kernel.h>
+#include <linux/err.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/mfd/ti_ssp.h>
+
+#define MODE_BITS	(SPI_CPHA | SPI_CPOL | SPI_CS_HIGH)
+
+struct ti_ssp_spi {
+	struct spi_master		*master;
+	struct device			*dev;
+	spinlock_t			lock;
+	struct list_head		msg_queue;
+	struct completion		complete;
+	bool				shutdown;
+	struct workqueue_struct		*workqueue;
+	struct work_struct		work;
+	u8				mode, bpw;
+	int				cs_active;
+	u32				pc_en, pc_dis, pc_wr, pc_rd;
+	void				(*select)(int cs);
+};
+
+static u32 ti_ssp_spi_rx(struct ti_ssp_spi *hw)
+{
+	u32 ret;
+
+	ti_ssp_run(hw->dev, hw->pc_rd, 0, &ret);
+	return ret;
+}
+
+static void ti_ssp_spi_tx(struct ti_ssp_spi *hw, u32 data)
+{
+	ti_ssp_run(hw->dev, hw->pc_wr, data << (32 - hw->bpw), NULL);
+}
+
+static int ti_ssp_spi_txrx(struct ti_ssp_spi *hw, struct spi_message *msg,
+		       struct spi_transfer *t)
+{
+	int count;
+
+	if (hw->bpw <= 8) {
+		u8		*rx = t->rx_buf;
+		const u8	*tx = t->tx_buf;
+
+		for (count = 0; count < t->len; count += 1) {
+			if (t->tx_buf)
+				ti_ssp_spi_tx(hw, *tx++);
+			if (t->rx_buf)
+				*rx++ = ti_ssp_spi_rx(hw);
+		}
+	} else if (hw->bpw <= 16) {
+		u16		*rx = t->rx_buf;
+		const u16	*tx = t->tx_buf;
+
+		for (count = 0; count < t->len; count += 2) {
+			if (t->tx_buf)
+				ti_ssp_spi_tx(hw, *tx++);
+			if (t->rx_buf)
+				*rx++ = ti_ssp_spi_rx(hw);
+		}
+	} else {
+		u32		*rx = t->rx_buf;
+		const u32	*tx = t->tx_buf;
+
+		for (count = 0; count < t->len; count += 4) {
+			if (t->tx_buf)
+				ti_ssp_spi_tx(hw, *tx++);
+			if (t->rx_buf)
+				*rx++ = ti_ssp_spi_rx(hw);
+		}
+	}
+
+	msg->actual_length += count; /* bytes transferred */
+
+	dev_dbg(&msg->spi->dev, "xfer %s%s, %d bytes, %d bpw, count %d%s\n",
+		t->tx_buf ? "tx" : "", t->rx_buf ? "rx" : "", t->len,
+		hw->bpw, count, (count < t->len) ? " (under)" : "");
+
+	return (count < t->len) ? -EIO : 0; /* left over data */
+}
+
+static void ti_ssp_spi_chip_select(struct ti_ssp_spi *hw, int cs_active)
+{
+	cs_active = !!cs_active;
+	if (cs_active == hw->cs_active)
+		return;
+	ti_ssp_run(hw->dev, cs_active ? hw->pc_en : hw->pc_dis, 0, NULL);
+	hw->cs_active = cs_active;
+}
+
+#define __SHIFT_OUT(bits)	(SSP_OPCODE_SHIFT | SSP_OUT_MODE | \
+				 cs_en | clk | SSP_COUNT((bits) * 2 - 1))
+#define __SHIFT_IN(bits)	(SSP_OPCODE_SHIFT | SSP_IN_MODE  | \
+				 cs_en | clk | SSP_COUNT((bits) * 2 - 1))
+
+static int ti_ssp_spi_setup_transfer(struct ti_ssp_spi *hw, u8 bpw, u8 mode)
+{
+	int error, idx = 0;
+	u32 seqram[16];
+	u32 cs_en, cs_dis, clk;
+	u32 topbits, botbits;
+
+	mode &= MODE_BITS;
+	if (mode == hw->mode && bpw == hw->bpw)
+		return 0;
+
+	cs_en  = (mode & SPI_CS_HIGH) ? SSP_CS_HIGH : SSP_CS_LOW;
+	cs_dis = (mode & SPI_CS_HIGH) ? SSP_CS_LOW  : SSP_CS_HIGH;
+	clk    = (mode & SPI_CPOL)    ? SSP_CLK_HIGH : SSP_CLK_LOW;
+
+	/* Construct instructions */
+
+	/* Disable Chip Select */
+	hw->pc_dis = idx;
+	seqram[idx++] = SSP_OPCODE_DIRECT | SSP_OUT_MODE | cs_dis | clk;
+	seqram[idx++] = SSP_OPCODE_STOP   | SSP_OUT_MODE | cs_dis | clk;
+
+	/* Enable Chip Select */
+	hw->pc_en = idx;
+	seqram[idx++] = SSP_OPCODE_DIRECT | SSP_OUT_MODE | cs_en | clk;
+	seqram[idx++] = SSP_OPCODE_STOP   | SSP_OUT_MODE | cs_en | clk;
+
+	/* Reads and writes need to be split for bpw > 16 */
+	topbits = (bpw > 16) ? 16 : bpw;
+	botbits = bpw - topbits;
+
+	/* Write */
+	hw->pc_wr = idx;
+	seqram[idx++] = __SHIFT_OUT(topbits) | SSP_ADDR_REG;
+	if (botbits)
+		seqram[idx++] = __SHIFT_OUT(botbits)  | SSP_DATA_REG;
+	seqram[idx++] = SSP_OPCODE_STOP | SSP_OUT_MODE | cs_en | clk;
+
+	/* Read */
+	hw->pc_rd = idx;
+	if (botbits)
+		seqram[idx++] = __SHIFT_IN(botbits) | SSP_ADDR_REG;
+	seqram[idx++] = __SHIFT_IN(topbits) | SSP_DATA_REG;
+	seqram[idx++] = SSP_OPCODE_STOP | SSP_OUT_MODE | cs_en | clk;
+
+	error = ti_ssp_load(hw->dev, 0, seqram, idx);
+	if (error < 0)
+		return error;
+
+	error = ti_ssp_set_mode(hw->dev, ((mode & SPI_CPHA) ?
+					  0 : SSP_EARLY_DIN));
+	if (error < 0)
+		return error;
+
+	hw->bpw = bpw;
+	hw->mode = mode;
+
+	return error;
+}
+
+static void ti_ssp_spi_work(struct work_struct *work)
+{
+	struct ti_ssp_spi *hw = container_of(work, struct ti_ssp_spi, work);
+
+	spin_lock(&hw->lock);
+
+	 while (!list_empty(&hw->msg_queue)) {
+		struct spi_message	*m;
+		struct spi_device	*spi;
+		struct spi_transfer	*t = NULL;
+		int			status = 0;
+
+		m = container_of(hw->msg_queue.next, struct spi_message,
+				 queue);
+
+		list_del_init(&m->queue);
+
+		spin_unlock(&hw->lock);
+
+		spi = m->spi;
+
+		if (hw->select)
+			hw->select(spi->chip_select);
+
+		list_for_each_entry(t, &m->transfers, transfer_list) {
+			int bpw = spi->bits_per_word;
+			int xfer_status;
+
+			if (t->bits_per_word)
+				bpw = t->bits_per_word;
+
+			if (ti_ssp_spi_setup_transfer(hw, bpw, spi->mode) < 0)
+				break;
+
+			ti_ssp_spi_chip_select(hw, 1);
+
+			xfer_status = ti_ssp_spi_txrx(hw, m, t);
+			if (xfer_status < 0)
+				status = xfer_status;
+
+			if (t->delay_usecs)
+				udelay(t->delay_usecs);
+
+			if (t->cs_change)
+				ti_ssp_spi_chip_select(hw, 0);
+		}
+
+		ti_ssp_spi_chip_select(hw, 0);
+		m->status = status;
+		m->complete(m->context);
+
+		spin_lock(&hw->lock);
+	}
+
+	if (hw->shutdown)
+		complete(&hw->complete);
+
+	spin_unlock(&hw->lock);
+}
+
+static int ti_ssp_spi_setup(struct spi_device *spi)
+{
+	if (spi->bits_per_word > 32)
+		return -EINVAL;
+
+	return 0;
+}
+
+static int ti_ssp_spi_transfer(struct spi_device *spi, struct spi_message *m)
+{
+	struct ti_ssp_spi	*hw;
+	struct spi_transfer	*t;
+	int			error = 0;
+
+	m->actual_length = 0;
+	m->status = -EINPROGRESS;
+
+	hw = spi_master_get_devdata(spi->master);
+
+	if (list_empty(&m->transfers) || !m->complete)
+		return -EINVAL;
+
+	list_for_each_entry(t, &m->transfers, transfer_list) {
+		if (t->len && !(t->rx_buf || t->tx_buf)) {
+			dev_err(&spi->dev, "invalid xfer, no buffer\n");
+			return -EINVAL;
+		}
+
+		if (t->len && t->rx_buf && t->tx_buf) {
+			dev_err(&spi->dev, "invalid xfer, full duplex\n");
+			return -EINVAL;
+		}
+
+		if (t->bits_per_word > 32) {
+			dev_err(&spi->dev, "invalid xfer width %d\n",
+				t->bits_per_word);
+			return -EINVAL;
+		}
+	}
+
+	spin_lock(&hw->lock);
+	if (hw->shutdown) {
+		error = -ESHUTDOWN;
+		goto error_unlock;
+	}
+	list_add_tail(&m->queue, &hw->msg_queue);
+	queue_work(hw->workqueue, &hw->work);
+error_unlock:
+	spin_unlock(&hw->lock);
+	return error;
+}
+
+static int __devinit ti_ssp_spi_probe(struct platform_device *pdev)
+{
+	const struct ti_ssp_spi_data *pdata;
+	struct ti_ssp_spi *hw;
+	struct spi_master *master;
+	struct device *dev = &pdev->dev;
+	int error = 0;
+
+	pdata = dev->platform_data;
+	if (!pdata) {
+		dev_err(dev, "platform data not found\n");
+		return -EINVAL;
+	}
+
+	master = spi_alloc_master(dev, sizeof(struct ti_ssp_spi));
+	if (!master) {
+		dev_err(dev, "cannot allocate SPI master\n");
+		return -ENOMEM;
+	}
+
+	hw = spi_master_get_devdata(master);
+	platform_set_drvdata(pdev, hw);
+
+	hw->master = master;
+	hw->dev = dev;
+	hw->select = pdata->select;
+
+	spin_lock_init(&hw->lock);
+	init_completion(&hw->complete);
+	INIT_LIST_HEAD(&hw->msg_queue);
+	INIT_WORK(&hw->work, ti_ssp_spi_work);
+
+	hw->workqueue = create_singlethread_workqueue(dev_name(dev));
+	if (!hw->workqueue) {
+		error = -ENOMEM;
+		dev_err(dev, "work queue creation failed\n");
+		goto error_wq;
+	}
+
+	error = ti_ssp_set_iosel(hw->dev, pdata->iosel);
+	if (error < 0) {
+		dev_err(dev, "io setup failed\n");
+		goto error_iosel;
+	}
+
+	master->bus_num		= pdev->id;
+	master->num_chipselect	= pdata->num_cs;
+	master->mode_bits	= MODE_BITS;
+	master->flags		= SPI_MASTER_HALF_DUPLEX;
+	master->setup		= ti_ssp_spi_setup;
+	master->transfer	= ti_ssp_spi_transfer;
+
+	error = spi_register_master(master);
+	if (error) {
+		dev_err(dev, "master registration failed\n");
+		goto error_reg;
+	}
+
+	return 0;
+
+error_reg:
+error_iosel:
+	destroy_workqueue(hw->workqueue);
+error_wq:
+	spi_master_put(master);
+	return error;
+}
+
+static int __devexit ti_ssp_spi_remove(struct platform_device *pdev)
+{
+	struct ti_ssp_spi *hw = platform_get_drvdata(pdev);
+	int error;
+
+	hw->shutdown = 1;
+	while (!list_empty(&hw->msg_queue)) {
+		error = wait_for_completion_interruptible(&hw->complete);
+		if (error < 0) {
+			hw->shutdown = 0;
+			return error;
+		}
+	}
+	destroy_workqueue(hw->workqueue);
+	spi_unregister_master(hw->master);
+
+	return 0;
+}
+
+static struct platform_driver ti_ssp_spi_driver = {
+	.probe		= ti_ssp_spi_probe,
+	.remove		= __devexit_p(ti_ssp_spi_remove),
+	.driver		= {
+		.name	= "ti-ssp-spi",
+		.owner	= THIS_MODULE,
+	},
+};
+
+static int __init ti_ssp_spi_init(void)
+{
+	return platform_driver_register(&ti_ssp_spi_driver);
+}
+module_init(ti_ssp_spi_init);
+
+static void __exit ti_ssp_spi_exit(void)
+{
+	platform_driver_unregister(&ti_ssp_spi_driver);
+}
+module_exit(ti_ssp_spi_exit);
+
+MODULE_DESCRIPTION("SSP SPI Master");
+MODULE_AUTHOR("Cyril Chemparathy");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:ti-ssp-spi");
include/linux/mfd/ti_ssp.h +6 -0
index 021fe09..dbb4b43 100644
@@ -32,6 +32,12 @@ struct ti_ssp_data {
 	struct ti_ssp_dev_data	dev_data[2];
 };
 
+struct ti_ssp_spi_data {
+	unsigned long	iosel;
+	int		num_cs;
+	void		(*select)(int cs);
+};
+
 /*
  * Sequencer port IO pin configuration bits.  These do not correlate 1-1 with
  * the hardware.  The iosel field in the port data combines iosel1 and iosel2,
Signature · 13 lines
1.7.1


------------------------------------------------------------------------------
Protect Your Site and Customers from Malware Attacks
Learn about various malware tactics and how to avoid them. Understand 
malware threats, the impact they can have on your business, and how you 
can protect your company and customers by using code signing.
http://p.sf.net/sfu/oracle-sfdevnl
_______________________________________________
spi-devel-general mailing list
spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org
https://lists.sourceforge.net/lists/listinfo/spi-devel-general
#6 lore raw

PATCH v8 3/11 gpio: add ti-ssp gpio driver

In reply to a message not in the archive

TI's SSP controller pins can be directly read and written to behave like a GPIO. This patch adds a GPIO driver that exposes such functionality.

---
 drivers/gpio/Kconfig       |   10 ++
 drivers/gpio/Makefile      |    1 +
 drivers/gpio/ti-ssp-gpio.c |  207 ++++++++++++++++++++++++++++++++++++++++++++
 include/linux/mfd/ti_ssp.h |    4 +
 4 files changed, 222 insertions(+), 0 deletions(-)
 create mode 100644 drivers/gpio/ti-ssp-gpio.c
drivers/gpio/Kconfig +10 -0
index 3143ac7..05bbe4c 100644
@@ -128,6 +128,16 @@ config GPIO_VX855
 	  additional drivers must be enabled in order to use the
 	  functionality of the device.
 
+config GPIO_TI_SSP
+	tristate "TI Sequencer Serial Port - GPIO Support"
+	depends on MFD_TI_SSP
+	help
+	  Say yes here to support a GPIO interface on TI SSP port pins.
+	  Each SSP port translates into 4 GPIOs.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called ti-ssp-gpio.
+
 comment "I2C GPIO expanders:"
 
 config GPIO_MAX7300
drivers/gpio/Makefile +1 -0
index bdf3dde..0e2a844 100644
@@ -26,6 +26,7 @@ obj-$(CONFIG_GPIO_PL061)	+= pl061.o
 obj-$(CONFIG_GPIO_STMPE)	+= stmpe-gpio.o
 obj-$(CONFIG_GPIO_TC35892)	+= tc35892-gpio.o
 obj-$(CONFIG_GPIO_TIMBERDALE)	+= timbgpio.o
+obj-$(CONFIG_GPIO_TI_SSP)	+= ti-ssp-gpio.o
 obj-$(CONFIG_GPIO_TWL4030)	+= twl4030-gpio.o
 obj-$(CONFIG_GPIO_UCB1400)	+= ucb1400_gpio.o
 obj-$(CONFIG_GPIO_XILINX)	+= xilinx_gpio.o
drivers/gpio/ti-ssp-gpio.c new file +207 -0

207 lines not on this page · raw message

include/linux/mfd/ti_ssp.h +4 -0
index dbb4b43..10c65bb 100644
@@ -38,6 +38,10 @@ struct ti_ssp_spi_data {
 	void		(*select)(int cs);
 };
 
+struct ti_ssp_gpio_data {
+	int		start;
+};
+
 /*
  * Sequencer port IO pin configuration bits.  These do not correlate 1-1 with
  * the hardware.  The iosel field in the port data combines iosel1 and iosel2,
Signature · 9 lines
1.7.1


------------------------------------------------------------------------------
Protect Your Site and Customers from Malware Attacks
Learn about various malware tactics and how to avoid them. Understand 
malware threats, the impact they can have on your business, and how you 
can protect your company and customers by using code signing.
http://p.sf.net/sfu/oracle-sfdevnl
#7 lore raw

PATCH v8 4/11 backlight: add support for tps6116x controller

In reply to a message not in the archive

TPS6116x is an EasyScale backlight controller device. This driver supports TPS6116x devices connected on a single GPIO.

---
 drivers/video/backlight/Kconfig    |    7 +
 drivers/video/backlight/Makefile   |    2 +-
 drivers/video/backlight/tps6116x.c |  299 ++++++++++++++++++++++++++++++++++++
 3 files changed, 307 insertions(+), 1 deletions(-)
 create mode 100644 drivers/video/backlight/tps6116x.c
drivers/video/backlight/Kconfig +7 -0
index e54a337..06e868e 100644
@@ -307,6 +307,13 @@ config BACKLIGHT_PCF50633
 	  If you have a backlight driven by a NXP PCF50633 MFD, say Y here to
 	  enable its driver.
 
+config BACKLIGHT_TPS6116X
+	tristate "TPS6116X LCD Backlight"
+	depends on GENERIC_GPIO
+	help
+	  This driver controls the LCD backlight level for EasyScale capable
+	  SSP connected backlight controllers.
+
 endif # BACKLIGHT_CLASS_DEVICE
 
 endif # BACKLIGHT_LCD_SUPPORT
drivers/video/backlight/Makefile +1 -1
index 44c0f81..5d407c8 100644
@@ -35,4 +35,4 @@ obj-$(CONFIG_BACKLIGHT_ADP5520)	+= adp5520_bl.o
 obj-$(CONFIG_BACKLIGHT_ADP8860)	+= adp8860_bl.o
 obj-$(CONFIG_BACKLIGHT_88PM860X) += 88pm860x_bl.o
 obj-$(CONFIG_BACKLIGHT_PCF50633)	+= pcf50633-backlight.o
-
+obj-$(CONFIG_BACKLIGHT_TPS6116X)+= tps6116x.o
drivers/video/backlight/tps6116x.c new file +299 -0

299 lines not on this page · raw message

Signature · 9 lines
1.7.1


------------------------------------------------------------------------------
Protect Your Site and Customers from Malware Attacks
Learn about various malware tactics and how to avoid them. Understand 
malware threats, the impact they can have on your business, and how you 
can protect your company and customers by using code signing.
http://p.sf.net/sfu/oracle-sfdevnl
#8 lore raw

PATCH v8 5/11 davinci: add tnetv107x ssp platform device

In reply to a message not in the archive

This patch adds an SSP platform device definition for the tnetv107x soc family. The clock lookup entry has also been updated to match.

---
 arch/arm/mach-davinci/devices-tnetv107x.c      |   25 ++++++++++++++++++++++++
 arch/arm/mach-davinci/include/mach/tnetv107x.h |    2 +
 arch/arm/mach-davinci/tnetv107x.c              |    2 +-
 3 files changed, 28 insertions(+), 1 deletions(-)
arch/arm/mach-davinci/devices-tnetv107x.c +25 -0
index 85503de..6162cae 100644
@@ -35,6 +35,7 @@
 #define TNETV107X_SDIO0_BASE			0x08088700
 #define TNETV107X_SDIO1_BASE			0x08088800
 #define TNETV107X_KEYPAD_BASE			0x08088a00
+#define TNETV107X_SSP_BASE			0x08088c00
 #define TNETV107X_ASYNC_EMIF_CNTRL_BASE		0x08200000
 #define TNETV107X_ASYNC_EMIF_DATA_CE0_BASE	0x30000000
 #define TNETV107X_ASYNC_EMIF_DATA_CE1_BASE	0x40000000
@@ -342,6 +343,25 @@ static struct platform_device tsc_device = {
 	.resource	= tsc_resources,
 };
 
+static struct resource ssp_resources[] = {
+	{
+		.start	= TNETV107X_SSP_BASE,
+		.end	= TNETV107X_SSP_BASE + 0x1ff,
+		.flags	= IORESOURCE_MEM,
+	},
+	{
+		.start	= IRQ_TNETV107X_SSP,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device ssp_device = {
+	.name		= "ti-ssp",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(ssp_resources),
+	.resource	= ssp_resources,
+};
+
 void __init tnetv107x_devices_init(struct tnetv107x_device_info *info)
 {
 	int i, error;
@@ -380,4 +400,9 @@ void __init tnetv107x_devices_init(struct tnetv107x_device_info *info)
 		keypad_device.dev.platform_data = info->keypad_config;
 		platform_device_register(&keypad_device);
 	}
+
+	if (info->ssp_config) {
+		ssp_device.dev.platform_data = info->ssp_config;
+		platform_device_register(&ssp_device);
+	}
 }
arch/arm/mach-davinci/include/mach/tnetv107x.h +2 -0
index 5a681d8..89c1fdc 100644
@@ -34,6 +34,7 @@
 
 #include <linux/serial_8250.h>
 #include <linux/input/matrix_keypad.h>
+#include <linux/mfd/ti_ssp.h>
 
 #include <mach/mmc.h>
 #include <mach/nand.h>
@@ -44,6 +45,7 @@ struct tnetv107x_device_info {
 	struct davinci_mmc_config	*mmc_config[2];  /* 2 controllers */
 	struct davinci_nand_pdata	*nand_config[4]; /* 4 chipsels */
 	struct matrix_keypad_platform_data *keypad_config;
+	struct ti_ssp_data		*ssp_config;
 };
 
 extern struct platform_device tnetv107x_wdt_device;
arch/arm/mach-davinci/tnetv107x.c +1 -1
index 6fcdece..1b28fdd 100644
@@ -278,7 +278,7 @@ static struct clk_lookup clks[] = {
 	CLK(NULL,		"timer1",		&clk_timer1),
 	CLK("tnetv107x_wdt.0",	NULL,			&clk_wdt_arm),
 	CLK(NULL,		"clk_wdt_dsp",		&clk_wdt_dsp),
-	CLK("ti-ssp.0",		NULL,			&clk_ssp),
+	CLK("ti-ssp",		NULL,			&clk_ssp),
 	CLK(NULL,		"clk_tdm0",		&clk_tdm0),
 	CLK(NULL,		"clk_vlynq",		&clk_vlynq),
 	CLK(NULL,		"clk_mcdma",		&clk_mcdma),
Signature · 9 lines
1.7.1


------------------------------------------------------------------------------
Protect Your Site and Customers from Malware Attacks
Learn about various malware tactics and how to avoid them. Understand 
malware threats, the impact they can have on your business, and how you 
can protect your company and customers by using code signing.
http://p.sf.net/sfu/oracle-sfdevnl
#9 lore raw

PATCH v8 6/11 davinci: add ssp config for tnetv107x evm board

In reply to a message not in the archive

This patch adds SSP configuration and pin muxing info for tnetv107x evm boards.

---
 arch/arm/mach-davinci/board-tnetv107x-evm.c |   14 ++++++++++++++
 1 files changed, 14 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +14 -0
index a6db854..ef526b1 100644
@@ -99,6 +99,12 @@ static const short uart1_pins[] __initdata = {
 	-1
 };
 
+static const short ssp_pins[] __initdata = {
+	TNETV107X_SSP0_0, TNETV107X_SSP0_1, TNETV107X_SSP0_2,
+	TNETV107X_SSP1_0, TNETV107X_SSP1_1, TNETV107X_SSP1_2,
+	TNETV107X_SSP1_3, -1
+};
+
 static struct mtd_partition nand_partitions[] = {
 	/* bootloader (U-Boot, etc) in first 12 sectors */
 	{
@@ -196,17 +202,25 @@ static struct matrix_keypad_platform_data keypad_config = {
 	.no_autorepeat	= 0,
 };
 
+static struct ti_ssp_data ssp_config = {
+	.out_clock	= 250 * 1000,
+	.dev_data	= {
+	},
+};
+
 static struct tnetv107x_device_info evm_device_info __initconst = {
 	.serial_config		= &serial_config,
 	.mmc_config[1]		= &mmc_config,	/* controller 1 */
 	.nand_config[0]		= &nand_config,	/* chip select 0 */
 	.keypad_config		= &keypad_config,
+	.ssp_config		= &ssp_config,
 };
 
 static __init void tnetv107x_evm_board_init(void)
 {
 	davinci_cfg_reg_list(sdio1_pins);
 	davinci_cfg_reg_list(uart1_pins);
+	davinci_cfg_reg_list(ssp_pins);
 
 	tnetv107x_devices_init(&evm_device_info);
 }
Signature · 9 lines
1.7.1


------------------------------------------------------------------------------
Protect Your Site and Customers from Malware Attacks
Learn about various malware tactics and how to avoid them. Understand 
malware threats, the impact they can have on your business, and how you 
can protect your company and customers by using code signing.
http://p.sf.net/sfu/oracle-sfdevnl
#10 lore raw

PATCH v8 7/11 davinci: add spi devices on tnetv107x evm

In reply to a message not in the archive

This patch adds definitions for spi devices on the tnetv107x evm platform.

---
 arch/arm/mach-davinci/board-tnetv107x-evm.c |   43 +++++++++++++++++++++++++++
 1 files changed, 43 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +43 -0
index ef526b1..1a656e8 100644
@@ -25,6 +25,7 @@
 #include <linux/mtd/partitions.h>
 #include <linux/input.h>
 #include <linux/input/matrix_keypad.h>
+#include <linux/spi/spi.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach-types.h>
@@ -37,6 +38,7 @@
 
 #define EVM_MMC_WP_GPIO		21
 #define EVM_MMC_CD_GPIO		24
+#define EVM_SPI_CS_GPIO		54
 
 static int initialize_gpio(int gpio, char *desc)
 {
@@ -202,9 +204,45 @@ static struct matrix_keypad_platform_data keypad_config = {
 	.no_autorepeat	= 0,
 };
 
+static void spi_select_device(int cs)
+{
+	static int gpio;
+
+	if (!gpio) {
+		int ret;
+		ret = gpio_request(EVM_SPI_CS_GPIO, "spi chipsel");
+		if (ret < 0) {
+			pr_err("cannot open spi chipsel gpio\n");
+			gpio = -ENOSYS;
+			return;
+		} else {
+			gpio = EVM_SPI_CS_GPIO;
+			gpio_direction_output(gpio, 0);
+		}
+	}
+
+	if (gpio < 0)
+		return;
+
+	return gpio_set_value(gpio, cs ? 1 : 0);
+}
+
+static struct ti_ssp_spi_data spi_master_data = {
+	.num_cs	= 2,
+	.select	= spi_select_device,
+	.iosel	= SSP_PIN_SEL(0, SSP_CLOCK)	| SSP_PIN_SEL(1, SSP_DATA) |
+		  SSP_PIN_SEL(2, SSP_CHIPSEL)	| SSP_PIN_SEL(3, SSP_IN)   |
+		  SSP_INPUT_SEL(3),
+};
+
 static struct ti_ssp_data ssp_config = {
 	.out_clock	= 250 * 1000,
 	.dev_data	= {
+		[1] = {
+			.dev_name = "ti-ssp-spi",
+			.pdata = &spi_master_data,
+			.pdata_size = sizeof(spi_master_data),
+		},
 	},
 };
 
@@ -216,6 +254,9 @@ static struct tnetv107x_device_info evm_device_info __initconst = {
 	.ssp_config		= &ssp_config,
 };
 
+static struct spi_board_info spi_info[] __initconst = {
+};
+
 static __init void tnetv107x_evm_board_init(void)
 {
 	davinci_cfg_reg_list(sdio1_pins);
@@ -223,6 +264,8 @@ static __init void tnetv107x_evm_board_init(void)
 	davinci_cfg_reg_list(ssp_pins);
 
 	tnetv107x_devices_init(&evm_device_info);
+
+	spi_register_board_info(spi_info, ARRAY_SIZE(spi_info));
 }
 
 #ifdef CONFIG_SERIAL_8250_CONSOLE
Signature · 9 lines
1.7.1


------------------------------------------------------------------------------
Protect Your Site and Customers from Malware Attacks
Learn about various malware tactics and how to avoid them. Understand 
malware threats, the impact they can have on your business, and how you 
can protect your company and customers by using code signing.
http://p.sf.net/sfu/oracle-sfdevnl
#11 lore raw

PATCH v8 8/11 davinci: add tnetv107x evm regulators

In reply to a message not in the archive

This patch adds regulator and spi board info definitions for the tps6524x power management IC found on tnetv107x evm boards.

---
 arch/arm/mach-davinci/board-tnetv107x-evm.c |   85 +++++++++++++++++++++++++++
 1 files changed, 85 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +85 -0
index 1a656e8..ca23516 100644
@@ -26,6 +26,9 @@
 #include <linux/input.h>
 #include <linux/input/matrix_keypad.h>
 #include <linux/spi/spi.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/consumer.h>
+#include <linux/regulator/driver.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach-types.h>
@@ -254,7 +257,89 @@ static struct tnetv107x_device_info evm_device_info __initconst = {
 	.ssp_config		= &ssp_config,
 };
 
+static struct regulator_consumer_supply usb_consumers[] = {
+	REGULATOR_SUPPLY("vbus", "musb_hdrc.1"),
+};
+
+static struct regulator_consumer_supply lcd_consumers[] = {
+	REGULATOR_SUPPLY("vlcd", "tps6116x"),
+};
+
+static struct regulator_init_data regulators[] = {
+	{
+		.constraints		= {
+			.name		= "DCDC1",
+			.min_uV		= 1000000,
+			.max_uV		= 1000000,
+			.always_on	= 1,
+			.boot_on	= 1,
+		},
+	},
+	{
+		.constraints		= {
+			.name		= "DCDC2",
+			.min_uV		= 1800000,
+			.max_uV		= 1800000,
+			.always_on	= 1,
+			.boot_on	= 1,
+		},
+	},
+	{
+		.constraints		= {
+			.name		= "DCDC3",
+			.min_uV		= 3300000,
+			.max_uV		= 3300000,
+			.always_on	= 1,
+			.boot_on	= 1,
+		},
+	},
+	{
+		.constraints		= {
+			.name		= "LDO1",
+			.min_uV		= 4800000,
+			.max_uV		= 4800000,
+			.always_on	= 1,
+			.boot_on	= 1,
+		},
+	},
+	{
+		.constraints		= {
+			.name		= "LDO1",
+			.min_uV		= 3300000,
+			.max_uV		= 3300000,
+			.always_on	= 1,
+			.boot_on	= 1,
+		},
+	},
+	{
+		.num_consumer_supplies	= ARRAY_SIZE(usb_consumers),
+		.consumer_supplies	= usb_consumers,
+		.constraints		= {
+			.name		= "USB",
+			.min_uA		= 200000,
+			.max_uA		= 1000000,
+			.valid_ops_mask	= REGULATOR_CHANGE_CURRENT |
+					  REGULATOR_CHANGE_STATUS,
+		},
+	},
+	{
+		.num_consumer_supplies	= ARRAY_SIZE(lcd_consumers),
+		.consumer_supplies	= lcd_consumers,
+		.constraints		= {
+			.name		= "LCD",
+			.valid_ops_mask	= REGULATOR_CHANGE_STATUS,
+		},
+	},
+};
+
 static struct spi_board_info spi_info[] __initconst = {
+	{
+		.modalias	= "tps6524x",
+		.bus_num	= 1,
+		.chip_select	= 0,
+		.mode		= SPI_MODE_0,
+		.platform_data	= regulators,
+	},
 };
 
 static __init void tnetv107x_evm_board_init(void)
Signature · 9 lines
1.7.1


------------------------------------------------------------------------------
Protect Your Site and Customers from Malware Attacks
Learn about various malware tactics and how to avoid them. Understand 
malware threats, the impact they can have on your business, and how you 
can protect your company and customers by using code signing.
http://p.sf.net/sfu/oracle-sfdevnl
#12 lore raw

PATCH v8 9/11 davinci: add tnetv107x evm ti-ssp gpio device

In reply to a message not in the archive

This patch adds definitions to hook up one of the ti-ssp ports to the SSP GPIO driver.

---
 arch/arm/mach-davinci/board-tnetv107x-evm.c |   11 +++++++++++
 1 files changed, 11 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +11 -0
index ca23516..e3863dd 100644
@@ -39,6 +39,8 @@
 #include <mach/cp_intc.h>
 #include <mach/tnetv107x.h>
 
+#define SSP_GPIO_START		128
+
 #define EVM_MMC_WP_GPIO		21
 #define EVM_MMC_CD_GPIO		24
 #define EVM_SPI_CS_GPIO		54
@@ -238,9 +240,18 @@ static struct ti_ssp_spi_data spi_master_data = {
 		  SSP_INPUT_SEL(3),
 };
 
+static struct ti_ssp_gpio_data ssp_gpio_data = {
+	.start		= SSP_GPIO_START,
+};
+
 static struct ti_ssp_data ssp_config = {
 	.out_clock	= 250 * 1000,
 	.dev_data	= {
+		[0] = {
+			.dev_name = "ti-ssp-gpio",
+			.pdata = &ssp_gpio_data,
+			.pdata_size = sizeof(ssp_gpio_data),
+		},
 		[1] = {
 			.dev_name = "ti-ssp-spi",
 			.pdata = &spi_master_data,
Signature · 9 lines
1.7.1


------------------------------------------------------------------------------
Protect Your Site and Customers from Malware Attacks
Learn about various malware tactics and how to avoid them. Understand 
malware threats, the impact they can have on your business, and how you 
can protect your company and customers by using code signing.
http://p.sf.net/sfu/oracle-sfdevnl
#13 lore raw

PATCH v8 10/11 davinci: add tnetv107x evm backlight device

In reply to a message not in the archive

The tnetv107x evm board has a backlight device that is connected on one of the SSP ports. This patch adds the board definitions necessary to plug the backlight driver to the GPIO corresponding to this SSP pin.

---
 arch/arm/mach-davinci/board-tnetv107x-evm.c |   14 ++++++++++++++
 1 files changed, 14 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +14 -0
index e3863dd..ac62de2 100644
@@ -44,6 +44,7 @@
 #define EVM_MMC_WP_GPIO		21
 #define EVM_MMC_CD_GPIO		24
 #define EVM_SPI_CS_GPIO		54
+#define EVM_BACKLIGHT_GPIO	(SSP_GPIO_START + 2)
 
 static int initialize_gpio(int gpio, char *desc)
 {
@@ -353,6 +354,12 @@ static struct spi_board_info spi_info[] __initconst = {
 	},
 };
 
+static struct platform_device backlight_device = {
+	.name		= "tps6116x",
+	.id		= -1,
+	.dev.platform_data = (void *)EVM_BACKLIGHT_GPIO,
+};
+
 static __init void tnetv107x_evm_board_init(void)
 {
 	davinci_cfg_reg_list(sdio1_pins);
@@ -364,6 +371,13 @@ static __init void tnetv107x_evm_board_init(void)
 	spi_register_board_info(spi_info, ARRAY_SIZE(spi_info));
 }
 
+static int __init tnetv107x_evm_late_init(void)
+{
+	platform_device_register(&backlight_device);
+	return 0;
+}
+late_initcall(tnetv107x_evm_late_init);
+
 #ifdef CONFIG_SERIAL_8250_CONSOLE
 static int __init tnetv107x_evm_console_init(void)
 {
Signature · 9 lines
1.7.1


------------------------------------------------------------------------------
Protect Your Site and Customers from Malware Attacks
Learn about various malware tactics and how to avoid them. Understand 
malware threats, the impact they can have on your business, and how you 
can protect your company and customers by using code signing.
http://p.sf.net/sfu/oracle-sfdevnl
#14 lore raw

PATCH v8 11/11 davinci: add tnetv107x evm i2c eeprom device

In reply to a message not in the archive

The tnetv107x evm board has an I2C device connected on one of the SSP ports. This patch adds board definitions for a GPIO based I2C master, as well as definitions for the eeprom device on these boards.

---
 arch/arm/mach-davinci/board-tnetv107x-evm.c |   30 +++++++++++++++++++++++++++
 1 files changed, 30 insertions(+), 0 deletions(-)
arch/arm/mach-davinci/board-tnetv107x-evm.c +30 -0
index ac62de2..869af15 100644
@@ -29,6 +29,9 @@
 #include <linux/regulator/machine.h>
 #include <linux/regulator/consumer.h>
 #include <linux/regulator/driver.h>
+#include <linux/i2c.h>
+#include <linux/i2c/at24.h>
+#include <linux/i2c-gpio.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach-types.h>
@@ -44,6 +47,8 @@
 #define EVM_MMC_WP_GPIO		21
 #define EVM_MMC_CD_GPIO		24
 #define EVM_SPI_CS_GPIO		54
+#define EVM_I2C_SDA_GPIO	(SSP_GPIO_START + 0)
+#define EVM_I2C_SCL_GPIO	(SSP_GPIO_START + 1)
 #define EVM_BACKLIGHT_GPIO	(SSP_GPIO_START + 2)
 
 static int initialize_gpio(int gpio, char *desc)
@@ -360,6 +365,29 @@ static struct platform_device backlight_device = {
 	.dev.platform_data = (void *)EVM_BACKLIGHT_GPIO,
 };
 
+struct i2c_gpio_platform_data i2c_data = {
+	.sda_pin	= EVM_I2C_SDA_GPIO,
+	.scl_pin	= EVM_I2C_SCL_GPIO,
+};
+
+static struct platform_device i2c_device = {
+	.name		= "i2c-gpio",
+	.id		= 0,
+	.dev.platform_data = &i2c_data,
+};
+
+static struct at24_platform_data at24_config = {
+	.byte_len	= SZ_16K / 8,
+	.page_size	= 16,
+};
+
+static struct i2c_board_info i2c_info[] __initconst =  {
+	{
+		I2C_BOARD_INFO("24c16", 0x50),
+		.platform_data	= &at24_config,
+	},
+};
+
 static __init void tnetv107x_evm_board_init(void)
 {
 	davinci_cfg_reg_list(sdio1_pins);
@@ -369,11 +397,13 @@ static __init void tnetv107x_evm_board_init(void)
 	tnetv107x_devices_init(&evm_device_info);
 
 	spi_register_board_info(spi_info, ARRAY_SIZE(spi_info));
+	i2c_register_board_info(0, i2c_info, ARRAY_SIZE(i2c_info));
 }
 
 static int __init tnetv107x_evm_late_init(void)
 {
 	platform_device_register(&backlight_device);
+	platform_device_register(&i2c_device);
 	return 0;
 }
 late_initcall(tnetv107x_evm_late_init);
Signature · 9 lines
1.7.1


------------------------------------------------------------------------------
Protect Your Site and Customers from Malware Attacks
Learn about various malware tactics and how to avoid them. Understand 
malware threats, the impact they can have on your business, and how you 
can protect your company and customers by using code signing.
http://p.sf.net/sfu/oracle-sfdevnl
#15 lore raw
In reply to a message not in the archive
Quoted 3 lines · Cyril Chemparathy

TI's sequencer serial port (TI-SSP) is a jack-of-all-trades type of serial port device. It has a built-in programmable execution engine that can be programmed to operate as almost any serial bus (I2C, SPI, EasyScale, and others).

Hi Cyril,

Can you include Grant's ack and repost this a bit broader. Add LKML and linux-arm-kernel please.

Thanks,

Kevin

Quoted 91 lines

This patch series implements a driver stack that looks like the following:

                             +--------+
                             | eeprom | . . .
                             +--------+
   +-----------+             +--------------+ +---------+
   | regulator | . . .       |   i2c-gpio   | | 1-wire  | . . .
   +-----------+             +--------------+ +---------+
   +----------------------+  +--------------------------------+
   |       ssp-spi        |  |           ssp-gpio             |
   +----------------------+  +--------------------------------+
   +----------------------------------------------------------+
   |                            ssp                           |
   +----------------------------------------------------------+

Changes between v8 and v7 of this series:
- Reorder commits, removed regulator driver patch (already upstreamed)
- Renamed static function definitions to keep namespace clean (mfd, gpio)
- Removed instance pdata in mfd driver

Changes between v7 and v6 of this series:
- Workaround for iosel2 register not reading back set bits.
- Update backlight status once probe succeeds.

Changes between v6 and v5 of this series:
- Changed initcalls to module_init() across all drivers. This series now uses a late_initcall() in the board to delay initialization of gpio and regulator dependent devices.

Changes between v5 and v4 of this series:
- Moved drivers from misc/gpio/spi to mfd
- Removed implicit init-time iosel setup
- Minor cleanups in backlight driver

Changes between v3 and v4 of this series:
- Replaced polled wait for sequence termination with interrupt
- Improved locking within SSP driver
- Other minor cleanups

Changes between v2 and v3 of this series:
- Minor cleanups in Kconfig and Makefile ordering

Changes between v1 and v2 of this series:
- Replaced open()/close() semantics with dynamic platform_device registration on SSP probe.
- Removed user-land interface to regulator registers
- More sensible regulator constraints
- Other minor cleanups

Cyril Chemparathy (11):
mfd: add driver for sequencer serial port
spi: add ti-ssp spi master driver
gpio: add ti-ssp gpio driver
backlight: add support for tps6116x controller
davinci: add tnetv107x ssp platform device
davinci: add ssp config for tnetv107x evm board
davinci: add spi devices on tnetv107x evm
davinci: add tnetv107x evm regulators
davinci: add tnetv107x evm ti-ssp gpio device
davinci: add tnetv107x evm backlight device
davinci: add tnetv107x evm i2c eeprom device

 arch/arm/mach-davinci/board-tnetv107x-evm.c    |  197 ++++++++++
 arch/arm/mach-davinci/devices-tnetv107x.c      |   25 ++
 arch/arm/mach-davinci/include/mach/tnetv107x.h |    2 +
 arch/arm/mach-davinci/tnetv107x.c              |    2 +-
 drivers/gpio/Kconfig                           |   10 +
 drivers/gpio/Makefile                          |    1 +
 drivers/gpio/ti-ssp-gpio.c                     |  207 ++++++++++
 drivers/mfd/Kconfig                            |   11 +
 drivers/mfd/Makefile                           |    1 +
 drivers/mfd/ti-ssp.c                           |  476 ++++++++++++++++++++++++
 drivers/spi/Kconfig                            |   10 +
 drivers/spi/Makefile                           |    1 +
 drivers/spi/ti-ssp-spi.c                       |  402 ++++++++++++++++++++
 drivers/video/backlight/Kconfig                |    7 +
 drivers/video/backlight/Makefile               |    2 +-
 drivers/video/backlight/tps6116x.c             |  299 +++++++++++++++
 include/linux/mfd/ti_ssp.h                     |   97 +++++
 17 files changed, 1748 insertions(+), 2 deletions(-)
 create mode 100644 drivers/gpio/ti-ssp-gpio.c
 create mode 100644 drivers/mfd/ti-ssp.c
 create mode 100644 drivers/spi/ti-ssp-spi.c
 create mode 100644 drivers/video/backlight/tps6116x.c
 create mode 100644 include/linux/mfd/ti_ssp.h

_______________________________________________
Davinci-linux-open-source mailing list Davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/@public.gmane.org
http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source