powerpc: Fix some 6xx/7xxx CPU setup functions
PATCH 1/1 powerpc: Fix some 6xx/7xxx CPU setup functions
Some of those functions try to adjust the CPU features, for example to remove NAP support on some revisions. However, they seem to use r5 as an index into the CPU table entry, which might have been right a long time ago but no longer is. r4 is the right register to use.
This probably caused some off behaviours on some PowerMac variants using 750cx or 7455 processor revisions.
---
Can somebody with one of these PowerMacs test this ? I only managed to find a 7448 which not directly affected...
In absence of good testing I would appreciate a close inspection of the patch by different pairs of eyes :-)
Cheers,
Ben.
arch/powerpc/kernel/cpu_setup_6xx.S +20 -20
@@ -18,7 +18,7 @@ #include <asm/mmu.h> _GLOBAL(__setup_cpu_603) - mflr r4 + mflr r5 BEGIN_MMU_FTR_SECTION li r10,0 mtspr SPRN_SPRG_603_LRU,r10 /* init SW LRU tracking */
@@ -27,60 +27,60 @@ BEGIN_FTR_SECTION bl __init_fpu_registers END_FTR_SECTION_IFCLR(CPU_FTR_FPU_UNAVAILABLE) bl setup_common_caches - mtlr r4 + mtlr r5 blr _GLOBAL(__setup_cpu_604) - mflr r4 + mflr r5 bl setup_common_caches bl setup_604_hid0 - mtlr r4 + mtlr r5 blr _GLOBAL(__setup_cpu_750) - mflr r4 + mflr r5 bl __init_fpu_registers bl setup_common_caches bl setup_750_7400_hid0 - mtlr r4 + mtlr r5 blr _GLOBAL(__setup_cpu_750cx) - mflr r4 + mflr r5 bl __init_fpu_registers bl setup_common_caches bl setup_750_7400_hid0 bl setup_750cx - mtlr r4 + mtlr r5 blr _GLOBAL(__setup_cpu_750fx) - mflr r4 + mflr r5 bl __init_fpu_registers bl setup_common_caches bl setup_750_7400_hid0 bl setup_750fx - mtlr r4 + mtlr r5 blr _GLOBAL(__setup_cpu_7400) - mflr r4 + mflr r5 bl __init_fpu_registers bl setup_7400_workarounds bl setup_common_caches bl setup_750_7400_hid0 - mtlr r4 + mtlr r5 blr _GLOBAL(__setup_cpu_7410) - mflr r4 + mflr r5 bl __init_fpu_registers bl setup_7410_workarounds bl setup_common_caches bl setup_750_7400_hid0 li r3,0 mtspr SPRN_L2CR2,r3 - mtlr r4 + mtlr r5 blr _GLOBAL(__setup_cpu_745x) - mflr r4 + mflr r5 bl setup_common_caches bl setup_745x_specifics - mtlr r4 + mtlr r5 blr /* Enable caches for 603's, 604, 750 & 7400 */
@@ -194,10 +194,10 @@ setup_750cx: cror 4*cr0+eq,4*cr0+eq,4*cr1+eq cror 4*cr0+eq,4*cr0+eq,4*cr2+eq bnelr - lwz r6,CPU_SPEC_FEATURES(r5) + lwz r6,CPU_SPEC_FEATURES(r4) li r7,CPU_FTR_CAN_NAP andc r6,r6,r7 - stw r6,CPU_SPEC_FEATURES(r5) + stw r6,CPU_SPEC_FEATURES(r4) blr /* 750fx specific
@@ -225,12 +225,12 @@ BEGIN_FTR_SECTION andis. r11,r11,L3CR_L3E@h beq 1f END_FTR_SECTION_IFSET(CPU_FTR_L3CR) - lwz r6,CPU_SPEC_FEATURES(r5) + lwz r6,CPU_SPEC_FEATURES(r4) andi. r0,r6,CPU_FTR_L3_DISABLE_NAP beq 1f li r7,CPU_FTR_CAN_NAP andc r6,r6,r7 - stw r6,CPU_SPEC_FEATURES(r5) + stw r6,CPU_SPEC_FEATURES(r4) 1: mfspr r11,SPRN_HID0
Quoted 4 lines · Benjamin Herrenschmidt
Some of those functions try to adjust the CPU features, for example to remove NAP support on some revisions. However, they seem to use r5 as an index into the CPU table entry, which might have been right a long time ago but no longer is. r4 is the right register to use.
Can you quantify 'a long time ago'? Is this compiler dependent?
Quoted 3 lines
This probably caused some off behaviours on some PowerMac variants using 750cx or 7455 processor revisions.
what about a 750gx?
Quoted 7 lines
Signed-off-by Benjamin Herrenschmidt <[email protected]>---
Can somebody with one of these PowerMacs test this ? I only managed to find a 7448 which not directly affected...
I have a GigE (PowerMac 3,4?) with an upgrade card that has a pair of 7455s on it and an 8600 with a 750GX cpu card. I can probably test this on the GigE. It is running 2.6.36. Is that recent enough? The 8600 is not cooperating.
The GigE is running 2.6.36 compiled with 4.3.5 built from sources. It seems to run fine.
_______________________________________________
Quoted 4 lines
Linuxppc-dev mailing list
[email protected]
https://lists.ozlabs.org/listinfo/linuxppc-dev
Quoted 7 lines · kevin diggs
I have a GigE (PowerMac 3,4?) with an upgrade card that has a pair of 7455s on it and an 8600 with a 750GX cpu card. I can probably test this on the GigE. It is running 2.6.36. Is that recent enough? The 8600 is not cooperating.
The GigE is running 2.6.36 compiled with 4.3.5 built from sources. It seems to run fine.
The bug would have caused the kernel to allow enabling of "nap" mode when idle on machines where this is buggy and can cause loss of cache coherency among others. I really don't remember off hand which specific machines may or may not have been affected. But I'd like at least people to verify that my patches to "fix" that aren't causing a regression for people like you who don't seem to have problems :-)
The bug was introduced a while back in 2005.
Cheers,
Ben.