usb:gadget: Add SuperSpeed support to the Gadget Framework

535 lines not on this page · raw message

index 4f56e44..e9fa7d8 100644
@@ -51,6 +51,18 @@ struct usb_configuration;
  * @hs_descriptors: Table of high speed descriptors, using interface and
  *	string identifiers assigned during @bind().  If this pointer is null,
  *	the function will not be available at high speed.
+ * @ss_descriptors: Table of super speed descriptors. If
+ *	wasnt supplied by the FD during @bind() and
+ *	!ss_not_capble, will be generated automaticly with
+ *	default values while working in superspeed mode. If this
+ *	pointer is null after initiation, the function will not
+ *	be available at super speed.
+ * @ss_not_capable: This flag is used by the FD to indicate if
+ *	this function is SS capble. Meaning: if SS descriptors
+ *	weren't supplied by the FD, and the flag is set ss
+ *	descriptors will NOT be automatically generated
+ * @ss_desc_allocated: This flag indicates whether the ss descriptors were
+ *	dynamically allocated (and needs to be released).
  * @config: assigned when @usb_add_function() is called; this is the
  *	configuration with which this function is associated.
  * @bind: Before the gadget can register, all of its functions bind() to the

@@ -69,6 +81,10 @@ struct usb_configuration;
  * @setup: Used for interface-specific control requests.
  * @suspend: Notifies functions when the host stops sending USB traffic.
  * @resume: Notifies functions when the host restarts USB traffic.
+ * @get_status: Returns function status as a reply to
+ *	GetStatus() request when the recepient is Interface.
+ * @func_suspend: callback to be called when
+ *	SetFeature(FUNCTION_SUSPEND) is reseived
  *
  * A single USB function uses one or more interfaces, and should in most
  * cases support operation at both full and high speeds.  Each function is

@@ -98,6 +114,10 @@ struct usb_function {
 	struct usb_gadget_strings	**strings;
 	struct usb_descriptor_header	**descriptors;
 	struct usb_descriptor_header	**hs_descriptors;
+	struct usb_descriptor_header	**ss_descriptors;
+
+	unsigned			ss_desc_allocated:1;
+	unsigned			ss_not_capable:1;
 
 	struct usb_configuration	*config;
 

@@ -124,6 +144,10 @@ struct usb_function {
 	void			(*suspend)(struct usb_function *);
 	void			(*resume)(struct usb_function *);
 
+	/* USB 3.0 additions */
+	int			(*get_status)(struct usb_function *);
+	int			(*func_suspend)(struct usb_function *,
+						u8 suspend_opt);
 	/* private: */
 	/* internals */
 	struct list_head		list;

@@ -229,6 +253,7 @@ struct usb_configuration {
 	struct list_head	list;
 	struct list_head	functions;
 	u8			next_interface_id;
+	unsigned		superspeed:1;
 	unsigned		highspeed:1;
 	unsigned		fullspeed:1;
 	struct usb_function	*interface[MAX_CONFIG_INTERFACES];

index 1bb7b3e..339552b 100644
@@ -136,6 +136,8 @@ struct usb_ep_ops {
  *	descriptor that matches connection speed
  * @desc: endpoint descriptor.  This pointer is set before the endpoint is
  *	enabled and remains valid until the endpoint is disabled.
+ * @comp_desc: In case of SuperSpeed support, this is the endpoint companion
+ *	descriptor that is used to configure the endpoint
  *
  * the bus controller driver lists all the general purpose endpoints in
  * gadget->ep_list.  the control endpoint (gadget->ep0) is not in that list,

@@ -150,6 +152,7 @@ struct usb_ep {
 	unsigned		maxpacket:16;
 	u8				bEndpointAddress;
 	const struct usb_endpoint_descriptor	*desc;
+	const struct usb_ss_ep_comp_descriptor	*comp_desc;
 };
 
 /*-------------------------------------------------------------------------*/

@@ -417,6 +420,14 @@ static inline void usb_ep_fifo_flush(struct usb_ep *ep)
 
 /*-------------------------------------------------------------------------*/
 
+struct usb_dcd_config_params {
+	__u8  bU1devExitLat;	/* U1 Device exit Latency */
+#define USB_DEFULT_U1_DEV_EXIT_LAT	0x01	/* Less then 1 microsec */
+	__u16 bU2DevExitLat;	/* U2 Device exit Latency */
+#define USB_DEFULT_U2_DEV_EXIT_LAT	0x1F4	/* Less then 500 microsec */
+};
+
+
 struct usb_gadget;
 
 /* the rest of the api to the controller hardware: device operations,

@@ -431,6 +442,7 @@ struct usb_gadget_ops {
 	int	(*pullup) (struct usb_gadget *, int is_on);
 	int	(*ioctl)(struct usb_gadget *,
 				unsigned code, unsigned long param);
+	void	(*get_config_params)(struct usb_dcd_config_params *);
 };
 
 /**

@@ -522,6 +534,23 @@ static inline int gadget_is_dualspeed(struct usb_gadget *g)
 }
 
 /**
+ * gadget_is_superspeed() - return true if the hardware handles
+ * supperspeed
+ * @g: controller that might support supper speed
+ */
+static inline int gadget_is_superspeed(struct usb_gadget *g)
+{
+#ifdef CONFIG_USB_GADGET_SUPERSPEED
+	/* runtime test would check "g->is_superspeed" ... that might be
+	 * useful to work around hardware bugs, but is mostly pointless
+	 */
+	return 1;
+#else
+	return 0;
+#endif
+}
+
+/**
  * gadget_is_otg - return true iff the hardware is OTG-ready
  * @g: controller that might have a Mini-AB connector
  *