Skip to contentSkip to conversation

Compile with ADT and recipe fails builds on target.

DISCUSSION Edward Vidal 2 participants 2 messages Aug 5, 2015

lore
Share & tools
lore
#0 lore raw

Hello All,

Trying to use ADT to compile a package.  The package compiles and installs on the target core-image-sato for the Raspberry Pi 2 B.  Also trying to create a recipe. see recipe_gtkwave/gtkwave/gtkwave_3.6.66.bb at
https://github.com/develone/raspberrypi2_yocto.git
The recipe downloads the source code, unpacks and runs do_configure, but fails at
 ERROR: Function failed: do_qa_configure.

1.) "cd wkg/yocto/RaspberryPi2/poky/"

2.) ". oe-init-build-env"

3.) "bitbale core-image-sato -c populate_sdk"

4.) "sudo tmp/deploy/sdk/poky-glibc-x86_64-core-image-sato-cortexa7hf-vfp-vfpv4-neon-toolchain-1.8+snapshot.sh"

5.) "cd ~/"

6.) "tar xfz wkg/yocto/downloads/gtkwave-3.3.66.tar.gz"

7.) "cd gtkwave-3.3.66/"

8.) "source /opt/poky/1.8+snapshot/environment-setup-cortexa7hf-vfp-vfpv4-neon-poky-linux-gnueabi"

9.a) "./configure ${CONFIGURE_FLAGS}"
checking for Tcl configuration... configure: error: Can't find Tcl configuration definitions. Use --with-tcl to specify a directory containing tclConfig.sh

Should the ADT be able to find theses since they are located at
ls /opt/poky/1.8+snapshot/sysroots/cortexa7hf-vfp-vfpv4-neon-poky-linux-gnueabi/usr/lib/tclConfig.sh ls /opt/poky/1.8+snapshot/sysroots/cortexa7hf-vfp-vfpv4-neon-poky-linux-gnueabi/usr/lib/tkConfig.sh without have to set the path

9.b) "./configure ${CONFIGURE_FLAGS} --with-tcl=/home/vidal/wkg/yocto/RaspberryPi2/poky/build/tmp/sysroots/raspberrypi2/usr/lib --with-tk=/home/vidal/wkg/yocto/RaspberryPi2/poky/build/tmp/sysroots/raspberrypi2/usr/lib"

This goes further with the following warning

config.status: executing depfiles commands
configure: WARNING: unrecognized options: --with-libtool-sysroot

Thanks in advance. Edward Vidal Jr.
e-mail [email protected]
915-595-1613

#1 lore raw
Quoted 34 lines · Edward Vidal

Hello All,

Trying to use ADT to compile a package. The package compiles and installs on the target core-image-sato for the Raspberry Pi 2 B. Also trying to create a recipe. see
recipe_gtkwave/gtkwave/gtkwave_3.6.66.bb at
https://github.com/develone/raspberrypi2_yocto.git
The recipe downloads the source code, unpacks and runs do_configure, but fails at
ERROR: Function failed: do_qa_configure.

1.) "cd wkg/yocto/RaspberryPi2/poky/"

2.) ". oe-init-build-env"

3.) "bitbale core-image-sato -c populate_sdk"

4.) "sudo tmp/deploy/sdk/poky-glibc-x86_64-core-image-sato-cortexa7hf-vfp-vfpv4-neon-toolchain-1.8+snapshot.sh"

5.) "cd ~/"

6.) "tar xfz wkg/yocto/downloads/gtkwave-3.3.66.tar.gz"

7.) "cd gtkwave-3.3.66/"

8.) "source /opt/poky/1.8+snapshot/environment-setup-cortexa7hf-vfp-vfpv4-neon-poky-linux-gnueabi"

9.a) "./configure ${CONFIGURE_FLAGS}"
checking for Tcl configuration... configure: error: Can't find Tcl configuration definitions. Use --with-tcl to specify a directory containing tclConfig.sh

Quoted 6 lines

Should the ADT be able to find theses since they are located at
ls /opt/poky/1.8+snapshot/sysroots/cortexa7hf-vfp-vfpv4-neon-poky-linux-gnueabi/usr/lib/tclConfig.sh ls /opt/poky/1.8+snapshot/sysroots/cortexa7hf-vfp-vfpv4-neon-poky-linux-gnueabi/usr/lib/tkConfig.sh without have to set the path

you need to find out how TCL is used here. If its used during build or is it required during runtime as well.
its not different when you do native compile but OE is all about cross compiling where it will matter.
If its only needed during build then you will depend on tcl-native in recipe. If its also needed during runtime you will add tcl to DEPENDS as well. You will also need to add nativesdk-tcl and any other dependencies when creating SDK

Quoted 22 lines

9.b) "./configure ${CONFIGURE_FLAGS} --with-tcl=/home/vidal/wkg/yocto/RaspberryPi2/poky/build/tmp/sysroots/raspberrypi2/usr/lib --with-tk=/home/vidal/wkg/yocto/RaspberryPi2/poky/build/tmp/sysroots/raspberrypi2/usr/lib"

This goes further with the following warning

config.status: executing depfiles commands
configure: WARNING: unrecognized options: --with-libtool-sysroot

Thanks in advance.

Edward Vidal Jr.
e-mail [email protected]
915-595-1613

--
_______________________________________________
yocto mailing list
[email protected]
https://lists.yoctoproject.org/listinfo/yocto