ASoC: Add MAX9850 codec driver
PATCH 1/1 ASoC: Add MAX9850 codec driver
This patch adds ASoC support for the MAX9850 codec with headphone amplifier.
Supported features:
- Playback
- 16, 20 and 24 bit audio
- 8k - 48k sample rates
- DAPM
Only 16 bit audio was tested while the codec was connected to an AT91SAM9G20 SSC in master mode.
---
I've all ready sent this patch some time ago, but it hung in the moderation queue. This is a slightly modified version. Unfortunately I do not have the hardware anymore to test suggested changes that alter function.
sound/soc/codecs/Kconfig | 4 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/max9850.c | 358 ++++++++++++++++++++++++++++++++++++++++++++ sound/soc/codecs/max9850.h | 41 +++++ 4 files changed, 405 insertions(+), 0 deletions(-) create mode 100644 sound/soc/codecs/max9850.c create mode 100644 sound/soc/codecs/max9850.h
sound/soc/codecs/Kconfig +4 -0
@@ -31,6 +31,7 @@ config SND_SOC_ALL_CODECS select SND_SOC_DA7210 if I2C select SND_SOC_JZ4740_CODEC if SOC_JZ4740 select SND_SOC_MAX98088 if I2C + select SND_SOC_MAX9850 if I2C select SND_SOC_MAX9877 if I2C select SND_SOC_PCM3008 select SND_SOC_SN95031 if INTEL_SCU_IPC
@@ -179,6 +180,9 @@ config SND_SOC_DMIC config SND_SOC_MAX98088 tristate +config SND_SOC_MAX9850 + tristate + config SND_SOC_PCM3008 tristate
sound/soc/codecs/Makefile +2 -0
@@ -18,6 +18,7 @@ snd-soc-da7210-objs := da7210.o snd-soc-dmic-objs := dmic.o snd-soc-l3-objs := l3.o snd-soc-max98088-objs := max98088.o +snd-soc-max9850-objs := max9850.o snd-soc-pcm3008-objs := pcm3008.o snd-soc-alc5623-objs := alc5623.o snd-soc-sn95031-objs := sn95031.o
@@ -102,6 +103,7 @@ obj-$(CONFIG_SND_SOC_DMIC) += snd-soc-dmic.o obj-$(CONFIG_SND_SOC_L3) += snd-soc-l3.o obj-$(CONFIG_SND_SOC_JZ4740_CODEC) += snd-soc-jz4740-codec.o obj-$(CONFIG_SND_SOC_MAX98088) += snd-soc-max98088.o +obj-$(CONFIG_SND_SOC_MAX9850) += snd-soc-max9850.o obj-$(CONFIG_SND_SOC_PCM3008) += snd-soc-pcm3008.o obj-$(CONFIG_SND_SOC_SN95031) +=snd-soc-sn95031.o obj-$(CONFIG_SND_SOC_SPDIF) += snd-soc-spdif.o
sound/soc/codecs/max9850.c new file +358 -0
358 lines not on this page · raw message
sound/soc/codecs/max9850.h new file +41 -0
41 lines not on this page · raw message
Signature · 1 line
1.7.2.3
Quoted 114 lines · Christian Glindkamp
This patch adds ASoC support for the MAX9850 codec with headphone amplifier.
Supported features:
- Playback
- 16, 20 and 24 bit audio
- 8k - 48k sample rates
- DAPMOnly 16 bit audio was tested while the codec was connected to an AT91SAM9G20 SSC in master mode.
Signed-off-by Christian Glindkamp <[email protected]>---
I've all ready sent this patch some time ago, but it hung in the moderation queue. This is a slightly modified version. Unfortunately I do not have the hardware anymore to test suggested changes that alter function.
sound/soc/codecs/Kconfig | 4 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/max9850.c | 358 ++++++++++++++++++++++++++++++++++++++++++++ sound/soc/codecs/max9850.h | 41 +++++ 4 files changed, 405 insertions(+), 0 deletions(-) create mode 100644 sound/soc/codecs/max9850.c create mode 100644 sound/soc/codecs/max9850.hsound/soc/codecs/Kconfig +4
-0@@ -31,6 +31,7 @@ config SND_SOC_ALL_CODECS select SND_SOC_DA7210 if I2C select SND_SOC_JZ4740_CODEC if SOC_JZ4740 select SND_SOC_MAX98088 if I2C + select SND_SOC_MAX9850 if I2C select SND_SOC_MAX9877 if I2C select SND_SOC_PCM3008 select SND_SOC_SN95031 if INTEL_SCU_IPC@@ -179,6 +180,9 @@ config SND_SOC_DMIC config SND_SOC_MAX98088 tristate +config SND_SOC_MAX9850 + tristate + config SND_SOC_PCM3008 tristatesound/soc/codecs/Makefile +2
-0@@ -18,6 +18,7 @@ snd-soc-da7210-objs := da7210.o snd-soc-dmic-objs := dmic.o snd-soc-l3-objs := l3.o snd-soc-max98088-objs := max98088.o +snd-soc-max9850-objs := max9850.o snd-soc-pcm3008-objs := pcm3008.o snd-soc-alc5623-objs := alc5623.o snd-soc-sn95031-objs := sn95031.o@@ -102,6 +103,7 @@ obj-$(CONFIG_SND_SOC_DMIC) += snd-soc-dmic.o obj-$(CONFIG_SND_SOC_L3) += snd-soc-l3.o obj-$(CONFIG_SND_SOC_JZ4740_CODEC) += snd-soc-jz4740-codec.o obj-$(CONFIG_SND_SOC_MAX98088) += snd-soc-max98088.o +obj-$(CONFIG_SND_SOC_MAX9850) += snd-soc-max9850.o obj-$(CONFIG_SND_SOC_PCM3008) += snd-soc-pcm3008.o obj-$(CONFIG_SND_SOC_SN95031) +=snd-soc-sn95031.o obj-$(CONFIG_SND_SOC_SPDIF) += snd-soc-spdif.osound/soc/codecs/max9850.c new file +39
-0@@ -0,0 +1,358 @@ +/* +* max9850.c -- codec driver for max9850 +* +* Copyright (C) 2011 taskit GmbH +* +* Author: Christian Glindkamp <[email protected]> +* +* Initial development of this code was funded by +* MICRONIC Computer Systeme GmbH, http://www.mcsberlin.de/ +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +* +*/ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/i2c.h> +#include <linux/slab.h> +#include <sound/pcm.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> +#include <sound/tlv.h> + +#include "max9850.h" + +struct max9850_priv { +unsigned int sysclk; +}; + +/* max9850 register cache */ +static const u8 max9850_reg[MAX9850_CACHEREGNUM ] = { +0x00 ,0x00 ,0x0c ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 +}; + +/* these registers are not used at the moment but provided for the sake of +* completeness */
sound/soc/codecs/max9850.c line 49
Quoted 10 lines
sound/soc/codecs/max9850.c new file +10
-0+static int max9850_volatile_register (unsigned int reg) +{ +switch (reg) { +case MAX9850_STATUSA : +case MAX9850_STATUSB : +return 1 ; +default : +return 0 ; + } +}
This code doesn't seem to have been developed against for-2.6.39. The signature of the volatile_register callback has changed to include a pointer to the snd_soc_codec structure.
sound/soc/codecs/max9850.c line 63
Quoted 13 lines
sound/soc/codecs/max9850.c new file +13
-0+static const unsigned int max9850_tlv[] = { +TLV_DB_RANGE_HEAD (4 ), +0x18 ,0x1f ,TLV_DB_SCALE_ITEM (-7450 ,400 ,0 ), +0x20 ,0x33 ,TLV_DB_SCALE_ITEM (-4150 ,200 ,0 ), +0x34 ,0x37 ,TLV_DB_SCALE_ITEM (-150 ,100 ,0 ), +0x38 ,0x3f ,TLV_DB_SCALE_ITEM (250 ,50 ,0 ), +}; + +static const struct snd_kcontrol_new max9850_controls[] = { +SOC_SINGLE_TLV ("Headphone Volume" ,MAX9850_VOLUME ,0 ,0x3f ,1 , max9850_tlv), +SOC_SINGLE ("Headphone Switch" ,MAX9850_VOLUME ,7 ,1 ,1 ), +SOC_SINGLE ("Mono" ,MAX9850_GENERAL_PURPOSE ,2 ,1 ,0 ), +};
Mono Switch?
Quoted 9 lines
sound/soc/codecs/max9850.c new file +9
-0+static const struct snd_kcontrol_new max9850_mixer_controls[] = { +SOC_DAPM_SINGLE ("Line In Switch" ,MAX9850_ENABLE ,1 ,1 ,0 ), +}; + +static const struct snd_soc_dapm_widget max9850_dapm_widgets[] = { +SND_SOC_DAPM_DAC ("DAC" ,"HiFi Playback" ,MAX9850_ENABLE ,0 ,0 ), +SND_SOC_DAPM_SUPPLY ("MCLK" ,MAX9850_ENABLE ,6 ,0 ,NULL ,0 ), +SND_SOC_DAPM_OUTPUT ("OUTL" ), +SND_SOC_DAPM_OUTPUT ("OUTR" ),
sound/soc/codecs/max9850.c line 83
Quoted 10 lines
sound/soc/codecs/max9850.c new file +10
-0+SND_SOC_DAPM_OUTPUT ("HPL" ), +SND_SOC_DAPM_OUTPUT ("HPR" ), +SND_SOC_DAPM_INPUT ("INL" ), +SND_SOC_DAPM_INPUT ("INR" ), +SND_SOC_DAPM_PGA ("Headphone Output" ,MAX9850_ENABLE ,3 ,0 ,NULL ,0 ), +SND_SOC_DAPM_MIXER ("Line Input" ,SND_SOC_NOPM ,0 ,0 ,NULL ,0 ), +SND_SOC_DAPM_MIXER_NAMED_CTL ("Output Mixer" ,MAX9850_ENABLE ,2 ,0 , + &max9850_mixer_controls[0 ], + ARRAY_SIZE(max9850_mixer_controls)), +};
Consider grouping the input and output pins logically separately.
Quoted 9 lines
sound/soc/codecs/max9850.c new file +9
-0+static const struct snd_soc_dapm_route intercon[] = { +/* output mixer */ + {"Output Mixer" ,NULL ,"DAC" }, + {"Output Mixer" ,"Line In Switch" ,"Line Input" }, + +/* outputs */ + {"Headphone Output" ,NULL ,"Output Mixer" }, + {"HPL" ,NULL ,"Headphone Output" }, + {"HPR" ,NULL ,"Headphone Output" },
sound/soc/codecs/max9850.c line 103
Quoted 10 lines
sound/soc/codecs/max9850.c new file +10
-0+ {"OUTL", NULL, "Output Mixer"}, + {"OUTR", NULL, "Output Mixer"}, + +/* inputs */ + {"Line Input", NULL, "INL"}, + {"Line Input", NULL, "INR"}, + +/* supplies */ + {"DAC", NULL, "MCLK"}, +};
Are all these really statically connected?
Quoted 109 lines
sound/soc/codecs/max9850.c new file +109
-0+static int max9850_hw_params (struct snd_pcm_substream *substream, +struct snd_pcm_hw_params *params, +struct snd_soc_dai *dai) +{ +struct snd_soc_codec *codec = dai->codec; +struct max9850_priv *max9850 =snd_soc_codec_get_drvdata (codec); +u64 lrclk_div; +u8 sf, da; + +/* lrclk_div = 2^22 * rate / iclk with iclk = mclk / sf */ + sf = (snd_soc_read (codec,MAX9850_CLOCK ) >>2 ) +1 ; + lrclk_div = (1 <<22 ); + lrclk_div *=params_rate (params); + lrclk_div *= sf; +do_div (lrclk_div, max9850->sysclk); + +snd_soc_write (codec,MAX9850_LRCLK_MSB , (lrclk_div >>8 ) &0x7f ); +snd_soc_write (codec,MAX9850_LRCLK_LSB , lrclk_div &0xff ); + + da =snd_soc_read (codec,MAX9850_DIGITAL_AUDIO ); +switch (params_format (params)) { +case SNDRV_PCM_FORMAT_S16_LE : +break ; +case SNDRV_PCM_FORMAT_S20_3LE : + da |=0x2 ; +break ; +case SNDRV_PCM_FORMAT_S24_LE : + da |=0x3 ; +break ; +default : +return -EINVAL ; + } +snd_soc_write (codec,MAX9850_DIGITAL_AUDIO , da); + +return 0 ; +} + +static int max9850_set_dai_sysclk (struct snd_soc_dai *codec_dai, +int clk_id,unsigned int freq,int dir) +{ +struct snd_soc_codec *codec = codec_dai->codec; +struct max9850_priv *max9850 =snd_soc_codec_get_drvdata (codec); + +/* calculate mclk -> iclk divider */ +if (freq <=13000000 ) +snd_soc_write (codec,MAX9850_CLOCK ,0x0 ); +else if (freq <=26000000 ) +snd_soc_write (codec,MAX9850_CLOCK ,0x4 ); +else if (freq <=40000000 ) +snd_soc_write (codec,MAX9850_CLOCK ,0x8 ); +else +return -EINVAL ; + + max9850->sysclk = freq; +return 0 ; +} + +static int max9850_set_dai_fmt (struct snd_soc_dai *codec_dai,unsigned int fmt) +{ +struct snd_soc_codec *codec = codec_dai->codec; +u8 da =0 ; + +/* set master/slave audio interface */ +switch (fmt &SND_SOC_DAIFMT_MASTER_MASK ) { +case SND_SOC_DAIFMT_CBM_CFM : + da |=MAX9850_MASTER ; +break ; +case SND_SOC_DAIFMT_CBS_CFS : +break ; +default : +return -EINVAL ; + } + +/* interface format */ +switch (fmt &SND_SOC_DAIFMT_FORMAT_MASK ) { +case SND_SOC_DAIFMT_I2S : + da |=MAX9850_DLY ; +break ; +case SND_SOC_DAIFMT_RIGHT_J : + da |=MAX9850_RTJ ; +break ; +case SND_SOC_DAIFMT_LEFT_J : +break ; +default : +return -EINVAL ; + } + +/* clock inversion */ +switch (fmt &SND_SOC_DAIFMT_INV_MASK ) { +case SND_SOC_DAIFMT_NB_NF : +break ; +case SND_SOC_DAIFMT_IB_IF : + da |=MAX9850_BCINV |MAX9850_INV ; +break ; +case SND_SOC_DAIFMT_IB_NF : + da |=MAX9850_BCINV ; +break ; +case SND_SOC_DAIFMT_NB_IF : + da |=MAX9850_INV ; +break ; +default : +return -EINVAL ; + } + +/* set da */ +snd_soc_write (codec,MAX9850_DIGITAL_AUDIO , da); + +return 0 ; +}
sound/soc/codecs/max9850.c line 223
Quoted 10 lines
sound/soc/codecs/max9850.c new file +10
-0+ +static int max9850_set_bias_level (struct snd_soc_codec *codec, +enum snd_soc_bias_level level) +{ +switch (level) { +case SND_SOC_BIAS_ON : +break ; +case SND_SOC_BIAS_PREPARE : +snd_soc_update_bits (codec,MAX9850_ENABLE ,MAX9850_SHDN , +MAX9850_SHDN );
Could possibly be handled by DAPM?
sound/soc/codecs/max9850.c line 226
Quoted 3 lines
sound/soc/codecs/max9850.c new file +3
-0+break ; +case SND_SOC_BIAS_STANDBY : +snd_soc_update_bits (codec,MAX9850_ENABLE ,MAX9850_SHDN ,0 );
Ditto.
sound/soc/codecs/max9850.c line 233
Quoted 7 lines
sound/soc/codecs/max9850.c new file +7
-0+break ; +case SND_SOC_BIAS_OFF : +break ; + } + codec->dapm.bias_level = level; +return 0 ; +}
I don't see any suspend/resume callbacks. It'd be good if you could provide default stubs that'd just set the bias level. Also syncing the cache when the bias level changes from BIAS_OFF to STANDBY would be a plus.
Quoted 28 lines
sound/soc/codecs/max9850.c new file +28
-0+#define MAX9850_RATES SNDRV_PCM_RATE_8000_48000 + +#define MAX9850_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE |\ + SNDRV_PCM_FMTBIT_S24_LE) + +static struct snd_soc_dai_ops max9850_dai_ops = { + .hw_params = max9850_hw_params, + .set_sysclk = max9850_set_dai_sysclk, + .set_fmt = max9850_set_dai_fmt, +}; + +static struct snd_soc_dai_driver max9850_dai = { + .name ="max9850-hifi" , + .playback = { + .stream_name ="Playback" , + .channels_min =1 , + .channels_max =2 , + .rates =MAX9850_RATES , + .formats =MAX9850_FORMATS + }, + .ops = &max9850_dai_ops, +}; + +static int max9850_probe (struct snd_soc_codec *codec) +{ +struct snd_soc_dapm_context *dapm = &codec->dapm; +int ret; +
sound/soc/codecs/max9850.c line 272
Quoted 10 lines
sound/soc/codecs/max9850.c new file +10
-0+ ret =snd_soc_codec_set_cache_io (codec,8 ,8 ,SND_SOC_I2C ); +if (ret <0 ) { +dev_err (codec->dev,"Failed to set cache I/O: %d\n" , ret); +return ret; + } + +/* enable zero-detect */ +snd_soc_update_bits (codec,MAX9850_GENERAL_PURPOSE ,1 ,1 ); +/* enable charge pump, disable everything else */ +snd_soc_write (codec,MAX9850_ENABLE ,0x30 );
DAPM?
Quoted 8 lines
sound/soc/codecs/max9850.c new file +8
-0+/* enable slew-rate control */ +snd_soc_update_bits (codec,MAX9850_VOLUME ,0x40 ,0x40 ); +/* set slew-rate 125ms */ +snd_soc_update_bits (codec,MAX9850_CHARGE_PUMP ,0xff ,0xc0 ); + +snd_soc_dapm_new_controls (dapm, max9850_dapm_widgets, +ARRAY_SIZE (max9850_dapm_widgets)); +snd_soc_dapm_add_routes (dapm, intercon,ARRAY_SIZE (intercon));
sound/soc/codecs/max9850.c line 290
Quoted 10 lines
sound/soc/codecs/max9850.c new file +10
-0+ +snd_soc_add_controls (codec, max9850_controls, +ARRAY_SIZE (max9850_controls)); + +return 0 ; +} +static int max9850_remove (struct snd_soc_codec *codec) +{ +return 0 ; +}
Setting the bias level to OFF would be preferable here.
Quoted 35 lines
sound/soc/codecs/max9850.c new file +35
-0+static struct snd_soc_codec_driver soc_codec_dev_max9850 = { + .probe = max9850_probe, + .remove = max9850_remove, + .set_bias_level = max9850_set_bias_level, + .reg_cache_size =ARRAY_SIZE (max9850_reg), + .reg_word_size =sizeof (u8), + .reg_cache_default = max9850_reg, + .volatile_register = max9850_volatile_register, +}; + +static int __devinit max9850_i2c_probe (struct i2c_client *i2c, +const struct i2c_device_id *id) +{ +struct max9850_priv *max9850; +int ret; + + max9850 =kzalloc (sizeof (struct max9850_priv ),GFP_KERNEL ); +if (max9850 ==NULL ) +return -ENOMEM ; + +i2c_set_clientdata (i2c, max9850); + + ret =snd_soc_register_codec (&i2c->dev, + &soc_codec_dev_max9850, &max9850_dai,1 ); +if (ret <0 ) +kfree (max9850); +return ret; +} + +static __devexit int max9850_i2c_remove(struct i2c_client *client) +{ +snd_soc_unregister_codec (&client->dev); +kfree (i2c_get_clientdata (client)); +return 0 ; +}
sound/soc/codecs/max9850.c line 336
Quoted 10 lines
sound/soc/codecs/max9850.c new file +10
-0+ +static const struct i2c_device_id max9850_i2c_id[] = { + {"max9850" ,0 }, + { } +}; +MODULE_DEVICE_TABLE (i2c, max9850_i2c_id); + +static struct i2c_driver max9850_i2c_driver = { + .driver = { + .name ="max9850-codec" ,
Remove the `-codec'.
Quoted 76 lines
sound/soc/codecs/max9850.c new file +22
-0+ .owner = THIS_MODULE, + }, + .probe = max9850_i2c_probe, + .remove = __devexit_p(max9850_i2c_remove), + .id_table = max9850_i2c_id, +}; + +static int __init max9850_init (void ) +{ +return i2c_add_driver (&max9850_i2c_driver); +} +module_init (max9850_init); + +static void __exit max9850_exit(void) +{ +i2c_del_driver (&max9850_i2c_driver); +} +module_exit (max9850_exit); + +MODULE_AUTHOR ("Christian Glindkamp <[email protected]>" ); +MODULE_DESCRIPTION ("ASoC MAX9850 codec driver" ); +MODULE_LICENSE ("GPL" );sound/soc/codecs/max9850.h new file +41
-0@@ -0,0 +1,41 @@ +/* +* max9850.h -- codec driver for max9850 +* +* Copyright (C) 2011 taskit GmbH +* Author: Christian Glindkamp <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +* +*/ + +#ifndef _MAX9850_H +#define _MAX9850_H + +#define MAX9850_STATUSA 0x00 +#define MAX9850_STATUSB 0x01 +#define MAX9850_VOLUME 0x02 +#define MAX9850_GENERAL_PURPOSE 0x03 +#define MAX9850_INTERRUPT 0x04 +#define MAX9850_ENABLE 0x05 +#define MAX9850_CLOCK 0x06 +#define MAX9850_CHARGE_PUMP 0x07 +#define MAX9850_LRCLK_MSB 0x08 +#define MAX9850_LRCLK_LSB 0x09 +#define MAX9850_DIGITAL_AUDIO 0x0a + +#define MAX9850_CACHEREGNUM 11 + +/* MAX9850_ENABLE */ +#define MAX9850_SHDN (1<<7) + +/* MAX9850_DIGITAL_AUDIO */ +#define MAX9850_MASTER (1<<7) +#define MAX9850_INV (1<<6) +#define MAX9850_BCINV (1<<5) +#define MAX9850_DLY (1<<3) +#define MAX9850_RTJ (1<<2) + +#endif Signature · 6 lines
1.7.2.3 _______________________________________________ Alsa-devel mailing list [email protected] http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
Resend to list, sorry for the noise Dimitris
As all ready said, I can't really test these changes at the moment but will at least compile test them. Additionally, alsa master currently does not build here for the arm architecture. Further comments below.
Quoted 121 lines · Dimitris Papastamos
Quoted 120 lines · Christian Glindkamp
This patch adds ASoC support for the MAX9850 codec with headphone amplifier.
Supported features:
- Playback
- 16, 20 and 24 bit audio
- 8k - 48k sample rates
- DAPMOnly 16 bit audio was tested while the codec was connected to an AT91SAM9G20 SSC in master mode.
Signed-off-by Christian Glindkamp <[email protected]>---
I've all ready sent this patch some time ago, but it hung in the moderation queue. This is a slightly modified version. Unfortunately I do not have the hardware anymore to test suggested changes that alter function.
sound/soc/codecs/Kconfig | 4 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/max9850.c | 358 ++++++++++++++++++++++++++++++++++++++++++++ sound/soc/codecs/max9850.h | 41 +++++ 4 files changed, 405 insertions(+), 0 deletions(-) create mode 100644 sound/soc/codecs/max9850.c create mode 100644 sound/soc/codecs/max9850.hsound/soc/codecs/Kconfig +4
-0@@ -31,6 +31,7 @@ config SND_SOC_ALL_CODECS select SND_SOC_DA7210 if I2C select SND_SOC_JZ4740_CODEC if SOC_JZ4740 select SND_SOC_MAX98088 if I2C + select SND_SOC_MAX9850 if I2C select SND_SOC_MAX9877 if I2C select SND_SOC_PCM3008 select SND_SOC_SN95031 if INTEL_SCU_IPC@@ -179,6 +180,9 @@ config SND_SOC_DMIC config SND_SOC_MAX98088 tristate +config SND_SOC_MAX9850 + tristate + config SND_SOC_PCM3008 tristatesound/soc/codecs/Makefile +2
-0@@ -18,6 +18,7 @@ snd-soc-da7210-objs := da7210.o snd-soc-dmic-objs := dmic.o snd-soc-l3-objs := l3.o snd-soc-max98088-objs := max98088.o +snd-soc-max9850-objs := max9850.o snd-soc-pcm3008-objs := pcm3008.o snd-soc-alc5623-objs := alc5623.o snd-soc-sn95031-objs := sn95031.o@@ -102,6 +103,7 @@ obj-$(CONFIG_SND_SOC_DMIC) += snd-soc-dmic.o obj-$(CONFIG_SND_SOC_L3) += snd-soc-l3.o obj-$(CONFIG_SND_SOC_JZ4740_CODEC) += snd-soc-jz4740-codec.o obj-$(CONFIG_SND_SOC_MAX98088) += snd-soc-max98088.o +obj-$(CONFIG_SND_SOC_MAX9850) += snd-soc-max9850.o obj-$(CONFIG_SND_SOC_PCM3008) += snd-soc-pcm3008.o obj-$(CONFIG_SND_SOC_SN95031) +=snd-soc-sn95031.o obj-$(CONFIG_SND_SOC_SPDIF) += snd-soc-spdif.osound/soc/codecs/max9850.c new file +45
-0@@ -0,0 +1,358 @@ +/* +* max9850.c -- codec driver for max9850 +* +* Copyright (C) 2011 taskit GmbH +* +* Author: Christian Glindkamp <[email protected]> +* +* Initial development of this code was funded by +* MICRONIC Computer Systeme GmbH, http://www.mcsberlin.de/ +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +* +*/ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/i2c.h> +#include <linux/slab.h> +#include <sound/pcm.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> +#include <sound/tlv.h> + +#include "max9850.h" + +struct max9850_priv { +unsigned int sysclk; +}; + +/* max9850 register cache */ +static const u8 max9850_reg[MAX9850_CACHEREGNUM ] = { +0x00 ,0x00 ,0x0c ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 +}; + +/* these registers are not used at the moment but provided for the sake of +* completeness */ +static int max9850_volatile_register (unsigned int reg) +{ +switch (reg) { +case MAX9850_STATUSA : +case MAX9850_STATUSB : +return 1 ;
Quoted 9 lines
sound/soc/codecs/max9850.c line 49
Quoted 4 lines
sound/soc/codecs/max9850.c new file +4
-0+default : +return 0 ; + } +}This code doesn't seem to have been developed against for-2.6.39. The signature of the
volatile_registercallback has changed to include a pointer to thesnd_soc_codecstructure.
Have not seen this branch. I will use a newer revision of alsa master if that is ok.
Quoted 29 lines
sound/soc/codecs/max9850.c line 63
Quoted 13 lines
sound/soc/codecs/max9850.c new file +13
-0+static const unsigned int max9850_tlv[] = { +TLV_DB_RANGE_HEAD (4 ), +0x18 ,0x1f ,TLV_DB_SCALE_ITEM (-7450 ,400 ,0 ), +0x20 ,0x33 ,TLV_DB_SCALE_ITEM (-4150 ,200 ,0 ), +0x34 ,0x37 ,TLV_DB_SCALE_ITEM (-150 ,100 ,0 ), +0x38 ,0x3f ,TLV_DB_SCALE_ITEM (250 ,50 ,0 ), +}; + +static const struct snd_kcontrol_new max9850_controls[] = { +SOC_SINGLE_TLV ("Headphone Volume" ,MAX9850_VOLUME ,0 ,0x3f ,1 , max9850_tlv), +SOC_SINGLE ("Headphone Switch" ,MAX9850_VOLUME ,7 ,1 ,1 ), +SOC_SINGLE ("Mono" ,MAX9850_GENERAL_PURPOSE ,2 ,1 ,0 ), +};Mono Switch?
Quoted 13 lines
sound/soc/codecs/max9850.c new file +13
-0+static const struct snd_kcontrol_new max9850_mixer_controls[] = { +SOC_DAPM_SINGLE ("Line In Switch" ,MAX9850_ENABLE ,1 ,1 ,0 ), +}; + +static const struct snd_soc_dapm_widget max9850_dapm_widgets[] = { +SND_SOC_DAPM_DAC ("DAC" ,"HiFi Playback" ,MAX9850_ENABLE ,0 ,0 ), +SND_SOC_DAPM_SUPPLY ("MCLK" ,MAX9850_ENABLE ,6 ,0 ,NULL ,0 ), +SND_SOC_DAPM_OUTPUT ("OUTL" ), +SND_SOC_DAPM_OUTPUT ("OUTR" ), +SND_SOC_DAPM_OUTPUT ("HPL" ), +SND_SOC_DAPM_OUTPUT ("HPR" ), +SND_SOC_DAPM_INPUT ("INL" ), +SND_SOC_DAPM_INPUT ("INR" ),
Quoted 9 lines
sound/soc/codecs/max9850.c line 83
Quoted 6 lines
sound/soc/codecs/max9850.c new file +6
-0+SND_SOC_DAPM_PGA ("Headphone Output" ,MAX9850_ENABLE ,3 ,0 ,NULL ,0 ), +SND_SOC_DAPM_MIXER ("Line Input" ,SND_SOC_NOPM ,0 ,0 ,NULL ,0 ), +SND_SOC_DAPM_MIXER_NAMED_CTL ("Output Mixer" ,MAX9850_ENABLE ,2 ,0 , + &max9850_mixer_controls[0 ], + ARRAY_SIZE(max9850_mixer_controls)), +};Consider grouping the input and output pins logically separately.
Do you mean something like that?
SND_SOC_DAPM_SUPPLY("MCLK", MAX9850_ENABLE, 6, 0, NULL, 0), SND_SOC_DAPM_MIXER_NAMED_CTL("Output Mixer", MAX9850_ENABLE, 2, 0,
&max9850_mixer_controls[0], ARRAY_SIZE(max9850_mixer_controls)),
SND_SOC_DAPM_PGA("Headphone Output", MAX9850_ENABLE, 3, 0, NULL, 0), SND_SOC_DAPM_DAC("DAC", "HiFi Playback", MAX9850_ENABLE, 0, 0), SND_SOC_DAPM_OUTPUT("OUTL"),SND_SOC_DAPM_OUTPUT("HPL"),SND_SOC_DAPM_OUTPUT("OUTR"),SND_SOC_DAPM_OUTPUT("HPR"),SND_SOC_DAPM_MIXER("Line Input", SND_SOC_NOPM, 0, 0, NULL, 0), SND_SOC_DAPM_INPUT("INL"),SND_SOC_DAPM_INPUT("INR"),
Quoted 13 lines
Quoted 13 lines
sound/soc/codecs/max9850.c new file +13
-0+static const struct snd_soc_dapm_route intercon[] = { +/* output mixer */ + {"Output Mixer" ,NULL ,"DAC" }, + {"Output Mixer" ,"Line In Switch" ,"Line Input" }, + +/* outputs */ + {"Headphone Output" ,NULL ,"Output Mixer" }, + {"HPL" ,NULL ,"Headphone Output" }, + {"HPR" ,NULL ,"Headphone Output" }, + {"OUTL" ,NULL ,"Output Mixer" }, + {"OUTR" ,NULL ,"Output Mixer" }, + +/* inputs */
Quoted 9 lines
sound/soc/codecs/max9850.c line 103
Quoted 6 lines
sound/soc/codecs/max9850.c new file +6
-0+ {"Line Input", NULL, "INL"}, + {"Line Input", NULL, "INR"}, + +/* supplies */ + {"DAC", NULL, "MCLK"}, +};Are all these really statically connected?
Yes, it is a relatively primitive codec. You can only switch on/off line in/out and the headphones. No routing is possible. Actually, what is called "Output Mixer" here is in reality line out, but it needs to be enabled for the headphone outputs to work.
Quoted 113 lines
Quoted 113 lines
sound/soc/codecs/max9850.c new file +113
-0+static int max9850_hw_params (struct snd_pcm_substream *substream, +struct snd_pcm_hw_params *params, +struct snd_soc_dai *dai) +{ +struct snd_soc_codec *codec = dai->codec; +struct max9850_priv *max9850 =snd_soc_codec_get_drvdata (codec); +u64 lrclk_div; +u8 sf, da; + +/* lrclk_div = 2^22 * rate / iclk with iclk = mclk / sf */ + sf = (snd_soc_read (codec,MAX9850_CLOCK ) >>2 ) +1 ; + lrclk_div = (1 <<22 ); + lrclk_div *=params_rate (params); + lrclk_div *= sf; +do_div (lrclk_div, max9850->sysclk); + +snd_soc_write (codec,MAX9850_LRCLK_MSB , (lrclk_div >>8 ) &0x7f ); +snd_soc_write (codec,MAX9850_LRCLK_LSB , lrclk_div &0xff ); + + da =snd_soc_read (codec,MAX9850_DIGITAL_AUDIO ); +switch (params_format (params)) { +case SNDRV_PCM_FORMAT_S16_LE : +break ; +case SNDRV_PCM_FORMAT_S20_3LE : + da |=0x2 ; +break ; +case SNDRV_PCM_FORMAT_S24_LE : + da |=0x3 ; +break ; +default : +return -EINVAL ; + } +snd_soc_write (codec,MAX9850_DIGITAL_AUDIO , da); + +return 0 ; +} + +static int max9850_set_dai_sysclk (struct snd_soc_dai *codec_dai, +int clk_id,unsigned int freq,int dir) +{ +struct snd_soc_codec *codec = codec_dai->codec; +struct max9850_priv *max9850 =snd_soc_codec_get_drvdata (codec); + +/* calculate mclk -> iclk divider */ +if (freq <=13000000 ) +snd_soc_write (codec,MAX9850_CLOCK ,0x0 ); +else if (freq <=26000000 ) +snd_soc_write (codec,MAX9850_CLOCK ,0x4 ); +else if (freq <=40000000 ) +snd_soc_write (codec,MAX9850_CLOCK ,0x8 ); +else +return -EINVAL ; + + max9850->sysclk = freq; +return 0 ; +} + +static int max9850_set_dai_fmt (struct snd_soc_dai *codec_dai,unsigned int fmt) +{ +struct snd_soc_codec *codec = codec_dai->codec; +u8 da =0 ; + +/* set master/slave audio interface */ +switch (fmt &SND_SOC_DAIFMT_MASTER_MASK ) { +case SND_SOC_DAIFMT_CBM_CFM : + da |=MAX9850_MASTER ; +break ; +case SND_SOC_DAIFMT_CBS_CFS : +break ; +default : +return -EINVAL ; + } + +/* interface format */ +switch (fmt &SND_SOC_DAIFMT_FORMAT_MASK ) { +case SND_SOC_DAIFMT_I2S : + da |=MAX9850_DLY ; +break ; +case SND_SOC_DAIFMT_RIGHT_J : + da |=MAX9850_RTJ ; +break ; +case SND_SOC_DAIFMT_LEFT_J : +break ; +default : +return -EINVAL ; + } + +/* clock inversion */ +switch (fmt &SND_SOC_DAIFMT_INV_MASK ) { +case SND_SOC_DAIFMT_NB_NF : +break ; +case SND_SOC_DAIFMT_IB_IF : + da |=MAX9850_BCINV |MAX9850_INV ; +break ; +case SND_SOC_DAIFMT_IB_NF : + da |=MAX9850_BCINV ; +break ; +case SND_SOC_DAIFMT_NB_IF : + da |=MAX9850_INV ; +break ; +default : +return -EINVAL ; + } + +/* set da */ +snd_soc_write (codec,MAX9850_DIGITAL_AUDIO , da); + +return 0 ; +} + +static int max9850_set_bias_level (struct snd_soc_codec *codec, +enum snd_soc_bias_level level) +{
Quoted 9 lines
sound/soc/codecs/max9850.c line 223
Quoted 6 lines
sound/soc/codecs/max9850.c new file +6
-0+switch (level) { +case SND_SOC_BIAS_ON : +break ; +case SND_SOC_BIAS_PREPARE : +snd_soc_update_bits (codec,MAX9850_ENABLE ,MAX9850_SHDN , +MAX9850_SHDN );Could possibly be handled by DAPM?
I could wire them to be the supply for the "Output Mixer". Without it being enabled, the codec does nothing anyway.
Quoted 6 lines
sound/soc/codecs/max9850.c line 226
Quoted 3 lines
sound/soc/codecs/max9850.c new file +3
-0+break ; +case SND_SOC_BIAS_STANDBY : +snd_soc_update_bits (codec,MAX9850_ENABLE ,MAX9850_SHDN ,0 );Ditto.
Quoted 12 lines
sound/soc/codecs/max9850.c line 233
Quoted 7 lines
sound/soc/codecs/max9850.c new file +7
-0+break ; +case SND_SOC_BIAS_OFF : +break ; + } + codec->dapm.bias_level = level; +return 0 ; +}I don't see any suspend/resume callbacks. It'd be good if you could provide default stubs that'd just set the bias level. Also syncing the cache when the bias level changes from
BIAS_OFFto STANDBY would be a plus.
Will look into it.
Quoted 32 lines
Quoted 32 lines
sound/soc/codecs/max9850.c new file +32
-0+#define MAX9850_RATES SNDRV_PCM_RATE_8000_48000 + +#define MAX9850_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE |\ + SNDRV_PCM_FMTBIT_S24_LE) + +static struct snd_soc_dai_ops max9850_dai_ops = { + .hw_params = max9850_hw_params, + .set_sysclk = max9850_set_dai_sysclk, + .set_fmt = max9850_set_dai_fmt, +}; + +static struct snd_soc_dai_driver max9850_dai = { + .name ="max9850-hifi" , + .playback = { + .stream_name ="Playback" , + .channels_min =1 , + .channels_max =2 , + .rates =MAX9850_RATES , + .formats =MAX9850_FORMATS + }, + .ops = &max9850_dai_ops, +}; + +static int max9850_probe (struct snd_soc_codec *codec) +{ +struct snd_soc_dapm_context *dapm = &codec->dapm; +int ret; + + ret =snd_soc_codec_set_cache_io (codec,8 ,8 ,SND_SOC_I2C ); +if (ret <0 ) { +dev_err (codec->dev,"Failed to set cache I/O: %d\n" , ret); +return ret;
Quoted 9 lines
sound/soc/codecs/max9850.c line 272
Quoted 6 lines
sound/soc/codecs/max9850.c new file +6
-0+ } + +/* enable zero-detect */ +snd_soc_update_bits (codec,MAX9850_GENERAL_PURPOSE ,1 ,1 ); +/* enable charge pump, disable everything else */ +snd_soc_write (codec,MAX9850_ENABLE ,0x30 );DAPM?
Charge pump could also be a supply for the Output Mixer. Have to find out how to toggle two bits at once via dapm (preferably without resorting to callbacks).
Quoted 149 lines
Quoted 8 lines
sound/soc/codecs/max9850.c new file +8
-0+/* enable slew-rate control */ +snd_soc_update_bits (codec,MAX9850_VOLUME ,0x40 ,0x40 ); +/* set slew-rate 125ms */ +snd_soc_update_bits (codec,MAX9850_CHARGE_PUMP ,0xff ,0xc0 ); + +snd_soc_dapm_new_controls (dapm, max9850_dapm_widgets, +ARRAY_SIZE (max9850_dapm_widgets)); +snd_soc_dapm_add_routes (dapm, intercon,ARRAY_SIZE (intercon));sound/soc/codecs/max9850.c line 290
Quoted 10 lines
sound/soc/codecs/max9850.c new file +10
-0+ +snd_soc_add_controls (codec, max9850_controls, +ARRAY_SIZE (max9850_controls)); + +return 0 ; +} +static int max9850_remove (struct snd_soc_codec *codec) +{ +return 0 ; +}Setting the bias level to OFF would be preferable here.
Quoted 35 lines
sound/soc/codecs/max9850.c new file +35
-0+static struct snd_soc_codec_driver soc_codec_dev_max9850 = { + .probe = max9850_probe, + .remove = max9850_remove, + .set_bias_level = max9850_set_bias_level, + .reg_cache_size =ARRAY_SIZE (max9850_reg), + .reg_word_size =sizeof (u8), + .reg_cache_default = max9850_reg, + .volatile_register = max9850_volatile_register, +}; + +static int __devinit max9850_i2c_probe (struct i2c_client *i2c, +const struct i2c_device_id *id) +{ +struct max9850_priv *max9850; +int ret; + + max9850 =kzalloc (sizeof (struct max9850_priv ),GFP_KERNEL ); +if (max9850 ==NULL ) +return -ENOMEM ; + +i2c_set_clientdata (i2c, max9850); + + ret =snd_soc_register_codec (&i2c->dev, + &soc_codec_dev_max9850, &max9850_dai,1 ); +if (ret <0 ) +kfree (max9850); +return ret; +} + +static __devexit int max9850_i2c_remove(struct i2c_client *client) +{ +snd_soc_unregister_codec (&client->dev); +kfree (i2c_get_clientdata (client)); +return 0 ; +}sound/soc/codecs/max9850.c line 336
Quoted 10 lines
sound/soc/codecs/max9850.c new file +10
-0+ +static const struct i2c_device_id max9850_i2c_id[] = { + {"max9850" ,0 }, + { } +}; +MODULE_DEVICE_TABLE (i2c, max9850_i2c_id); + +static struct i2c_driver max9850_i2c_driver = { + .driver = { + .name ="max9850-codec" ,Remove the `-codec'.
Quoted 76 lines
sound/soc/codecs/max9850.c new file +22
-0+ .owner = THIS_MODULE, + }, + .probe = max9850_i2c_probe, + .remove = __devexit_p(max9850_i2c_remove), + .id_table = max9850_i2c_id, +}; + +static int __init max9850_init (void ) +{ +return i2c_add_driver (&max9850_i2c_driver); +} +module_init (max9850_init); + +static void __exit max9850_exit(void) +{ +i2c_del_driver (&max9850_i2c_driver); +} +module_exit (max9850_exit); + +MODULE_AUTHOR ("Christian Glindkamp <[email protected]>" ); +MODULE_DESCRIPTION ("ASoC MAX9850 codec driver" ); +MODULE_LICENSE ("GPL" );sound/soc/codecs/max9850.h new file +41
-0@@ -0,0 +1,41 @@ +/* +* max9850.h -- codec driver for max9850 +* +* Copyright (C) 2011 taskit GmbH +* Author: Christian Glindkamp <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +* +*/ + +#ifndef _MAX9850_H +#define _MAX9850_H + +#define MAX9850_STATUSA 0x00 +#define MAX9850_STATUSB 0x01 +#define MAX9850_VOLUME 0x02 +#define MAX9850_GENERAL_PURPOSE 0x03 +#define MAX9850_INTERRUPT 0x04 +#define MAX9850_ENABLE 0x05 +#define MAX9850_CLOCK 0x06 +#define MAX9850_CHARGE_PUMP 0x07 +#define MAX9850_LRCLK_MSB 0x08 +#define MAX9850_LRCLK_LSB 0x09 +#define MAX9850_DIGITAL_AUDIO 0x0a + +#define MAX9850_CACHEREGNUM 11 + +/* MAX9850_ENABLE */ +#define MAX9850_SHDN (1<<7) + +/* MAX9850_DIGITAL_AUDIO */ +#define MAX9850_MASTER (1<<7) +#define MAX9850_INV (1<<6) +#define MAX9850_BCINV (1<<5) +#define MAX9850_DLY (1<<3) +#define MAX9850_RTJ (1<<2) + +#endif Signature · 6 lines
1.7.2.3 _______________________________________________ Alsa-devel mailing list [email protected] http://mailman.alsa-project.org/mailman/listinfo/alsa-devel_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
Quoted 3 lines · Christian Glindkamp
As all ready said, I can't really test these changes at the moment but will at least compile test them. Additionally, alsa master currently does not build here for the arm architecture. Further comments below.
I'm not sure what tree you're building against but mainline ASoC builds fine on ARM. ASoC changes should be against the latest for- branch of:
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound-2.6.git
(see MAINTAINERS).
Quoted 10 lines
Quoted 6 lines
sound/soc/codecs/max9850.c line 272
Quoted 4 lines
sound/soc/codecs/max9850.c new file +4
-0+/* enable zero-detect */ +snd_soc_update_bits (codec,MAX9850_GENERAL_PURPOSE ,1 ,1 ); +/* enable charge pump, disable everything else */ +snd_soc_write (codec,MAX9850_ENABLE ,0x30 );DAPM?
Charge pump could also be a supply for the Output Mixer. Have to find out how to toggle two bits at once via dapm (preferably without resorting to callbacks).
If you implement two widgets of the same type DAPM will try to compress them down into a single register write when updating so the effect will be to do a single update to both bits.
Quoted 25 lines · Christian Glindkamp
Quoted 9 lines
Quoted 9 lines
sound/soc/codecs/max9850.c new file +9
-0+static const struct snd_soc_dapm_widget max9850_dapm_widgets[] = { +SND_SOC_DAPM_DAC ("DAC" ,"HiFi Playback" ,MAX9850_ENABLE ,0 ,0 ), +SND_SOC_DAPM_SUPPLY ("MCLK" ,MAX9850_ENABLE ,6 ,0 ,NULL ,0 ), +SND_SOC_DAPM_OUTPUT ("OUTL" ), +SND_SOC_DAPM_OUTPUT ("OUTR" ), +SND_SOC_DAPM_OUTPUT ("HPL" ), +SND_SOC_DAPM_OUTPUT ("HPR" ), +SND_SOC_DAPM_INPUT ("INL" ), +SND_SOC_DAPM_INPUT ("INR" ),Quoted 9 lines
sound/soc/codecs/max9850.c line 83
Quoted 6 lines
sound/soc/codecs/max9850.c new file +6
-0+SND_SOC_DAPM_PGA ("Headphone Output" ,MAX9850_ENABLE ,3 ,0 ,NULL ,0 ), +SND_SOC_DAPM_MIXER ("Line Input" ,SND_SOC_NOPM ,0 ,0 ,NULL ,0 ), +SND_SOC_DAPM_MIXER_NAMED_CTL ("Output Mixer" ,MAX9850_ENABLE ,2 ,0 , + &max9850_mixer_controls[0 ], + ARRAY_SIZE(max9850_mixer_controls)), +};Consider grouping the input and output pins logically separately.
Do you mean something like that?
SND_SOC_DAPM_SUPPLY("MCLK", MAX9850_ENABLE, 6, 0, NULL, 0), SND_SOC_DAPM_MIXER_NAMED_CTL("Output Mixer",MAX9850_ENABLE, 2, 0,&max9850_mixer_controls[0], ARRAY_SIZE(max9850_mixer_controls)),
Quoted 9 lines
SND_SOC_DAPM_PGA("Headphone Output", MAX9850_ENABLE, 3, 0, NULL, 0),SND_SOC_DAPM_DAC("DAC", "HiFi Playback", MAX9850_ENABLE, 0, 0),SND_SOC_DAPM_OUTPUT("OUTL"),SND_SOC_DAPM_OUTPUT("HPL"),SND_SOC_DAPM_OUTPUT("OUTR"),SND_SOC_DAPM_OUTPUT("HPR"),SND_SOC_DAPM_MIXER("Line Input", SND_SOC_NOPM, 0, 0, NULL, 0),SND_SOC_DAPM_INPUT("INL"),SND_SOC_DAPM_INPUT("INR"),
Yea, that's fine. Although the standard thing to do is to group all the input pins at the beginning and all the output pins at the end. However this is a pretty primitive codec so it is not a problem as it stands now.
Quoted 3 lines
Charge pump could also be a supply for the Output Mixer. Have to find out how to toggle two bits at once via dapm (preferably without resorting to callbacks).
If they are in the same register and same type of widgets then as Mark mentioned the core guarantees that it'll be done in one register write.
I forgot to mention in the previous e-mail, that if you add the cache syncing support during resume or whenever we go from BIAS_OFF to STANDBY use the standard ASoC function for that, snd_soc_cache_sync(). Just in case you are looking at older examples.
Thanks,
Dimitris
Quoted 45 lines · Dimitris Papastamos
Quoted 25 lines · Christian Glindkamp
Quoted 9 lines
Quoted 9 lines
sound/soc/codecs/max9850.c new file +9
-0+static const struct snd_soc_dapm_widget max9850_dapm_widgets[] = { +SND_SOC_DAPM_DAC ("DAC" ,"HiFi Playback" ,MAX9850_ENABLE ,0 ,0 ), +SND_SOC_DAPM_SUPPLY ("MCLK" ,MAX9850_ENABLE ,6 ,0 ,NULL ,0 ), +SND_SOC_DAPM_OUTPUT ("OUTL" ), +SND_SOC_DAPM_OUTPUT ("OUTR" ), +SND_SOC_DAPM_OUTPUT ("HPL" ), +SND_SOC_DAPM_OUTPUT ("HPR" ), +SND_SOC_DAPM_INPUT ("INL" ), +SND_SOC_DAPM_INPUT ("INR" ),Quoted 9 lines
sound/soc/codecs/max9850.c line 83
Quoted 6 lines
sound/soc/codecs/max9850.c new file +6
-0+SND_SOC_DAPM_PGA ("Headphone Output" ,MAX9850_ENABLE ,3 ,0 ,NULL ,0 ), +SND_SOC_DAPM_MIXER ("Line Input" ,SND_SOC_NOPM ,0 ,0 ,NULL ,0 ), +SND_SOC_DAPM_MIXER_NAMED_CTL ("Output Mixer" ,MAX9850_ENABLE ,2 ,0 , + &max9850_mixer_controls[0 ], + ARRAY_SIZE(max9850_mixer_controls)), +};Consider grouping the input and output pins logically separately.
Do you mean something like that?
SND_SOC_DAPM_SUPPLY("MCLK", MAX9850_ENABLE, 6, 0, NULL, 0), SND_SOC_DAPM_MIXER_NAMED_CTL("Output Mixer",MAX9850_ENABLE, 2, 0,&max9850_mixer_controls[0], ARRAY_SIZE(max9850_mixer_controls)),Quoted 9 lines
SND_SOC_DAPM_PGA("Headphone Output", MAX9850_ENABLE, 3, 0, NULL, 0),SND_SOC_DAPM_DAC("DAC", "HiFi Playback", MAX9850_ENABLE, 0, 0),SND_SOC_DAPM_OUTPUT("OUTL"),SND_SOC_DAPM_OUTPUT("HPL"),SND_SOC_DAPM_OUTPUT("OUTR"),SND_SOC_DAPM_OUTPUT("HPR"),SND_SOC_DAPM_MIXER("Line Input", SND_SOC_NOPM, 0, 0, NULL, 0),SND_SOC_DAPM_INPUT("INL"),SND_SOC_DAPM_INPUT("INR"),Yea, that's fine. Although the standard thing to do is to group all the input pins at the beginning and all the output pins at the end. However this is a pretty primitive codec so it is not a problem as it stands now.
Quoted 3 lines
Charge pump could also be a supply for the Output Mixer. Have to find out how to toggle two bits at once via dapm (preferably without resorting to callbacks).
Quoted 8 lines
If they are in the same register and same type of widgets then as Mark mentioned the core guarantees that it'll be done in one register write.
I forgot to mention in the previous e-mail, that if you add the cache syncing support during resume or whenever we go from
BIAS_OFFto STANDBY use the standard ASoC function for that,snd_soc_cache_sync(). Just in case you are looking at older examples.
Do I understand it correctly, that all register writes that I do in the probe function would be overridden by the syncing so they would have to be moved to the standby code or put into the register cache array as default values?
Quoted 6 lines
Thanks,
Dimitris
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
Quoted 4 lines · Christian Glindkamp
Do I understand it correctly, that all register writes that I do in the probe function would be overridden by the syncing so they would have to be moved to the standby code or put into the register cache array as default values?
If you do any registers writes in the probe() function, in effect you will be changing the hardware state as well as the cache state. If after that point you sync the cache to the hardware, the altered cache will be synced, not the defaults cache. The core makes a copy of the defaults cache and uses that for syncing, or if you don't provide a default's cache it will use a zero-ed cache.
Note that volatile registers don't affect the cache, they bypass it completely.
Thanks,
Dimitris
Quoted 3 lines · Christian Glindkamp
I've all ready sent this patch some time ago, but it hung in the moderation queue. This is a slightly modified version. Unfortunately I do not have the hardware anymore to test suggested changes that alter function.
As mentioned in SubmittingPatches you should always CC maintainers on patches. This will bypass things like list moderation and also helps ensure that people see your mail on busy mailing lists.
Overall this looks pretty good.
sound/soc/codecs/max9850.c line 62
Quoted 4 lines
sound/soc/codecs/max9850.c new file +4
-0+static const struct snd_kcontrol_new max9850_controls[] = { +SOC_SINGLE_TLV ("Headphone Volume" ,MAX9850_VOLUME ,0 ,0x3f ,1 , max9850_tlv), +SOC_SINGLE ("Headphone Switch" ,MAX9850_VOLUME ,7 ,1 ,1 ), +SOC_SINGLE ("Mono" ,MAX9850_GENERAL_PURPOSE ,2 ,1 ,0 ),
...Switch.
sound/soc/codecs/max9850.c line 119
Quoted 6 lines
sound/soc/codecs/max9850.c new file +6
-0+/* lrclk_div = 2^22 * rate / iclk with iclk = mclk / sf */ + sf = (snd_soc_read (codec,MAX9850_CLOCK ) >>2 ) +1 ; + lrclk_div = (1 <<22 ); + lrclk_div *=params_rate (params); + lrclk_div *= sf; +do_div (lrclk_div, max9850->sysclk);
Should check that sysclk() has been set and return an error if not before doing the division here.
Quoted 4 lines
sound/soc/codecs/max9850.c new file +4
-0+ da =snd_soc_read (codec,MAX9850_DIGITAL_AUDIO ); +switch (params_format (params)) { +case SNDRV_PCM_FORMAT_S16_LE : +break ;
sound/soc/codecs/max9850.c line 137
Quoted 10 lines
sound/soc/codecs/max9850.c new file +10
-0+case SNDRV_PCM_FORMAT_S20_3LE : + da |=0x2 ; +break ; +case SNDRV_PCM_FORMAT_S24_LE : + da |=0x3 ; +break ; +default : +return -EINVAL ; + } +snd_soc_write (codec,MAX9850_DIGITAL_AUDIO , da);
Use snd_soc_update_bits() here. The above doesn't clear any of the bits so if 20 or 24 bit is set they'll get latched.
Quoted 5 lines
sound/soc/codecs/max9850.c new file +5
-0+static int max9850_set_bias_level (struct snd_soc_codec *codec, +enum snd_soc_bias_level level) +{ +switch (level) { +case SND_SOC_BIAS_ON :
sound/soc/codecs/max9850.c line 229
Quoted 10 lines
sound/soc/codecs/max9850.c new file +10
-0+break ; +case SND_SOC_BIAS_PREPARE : +snd_soc_update_bits (codec,MAX9850_ENABLE ,MAX9850_SHDN , +MAX9850_SHDN ); +break ; +case SND_SOC_BIAS_STANDBY : +snd_soc_update_bits (codec,MAX9850_ENABLE ,MAX9850_SHDN ,0 ); +break ; +case SND_SOC_BIAS_OFF : +break ;
This pattern looks awfully like you should set idle_bias_off for the CODEC and then move the code blocks down one power level - _SHDN sounds like a general power down for the device which fits better with the _OFF state.
Or use DAPM like Dimitris suggested.
sound/soc/codecs/max9850.c line 272
Quoted 2 lines
sound/soc/codecs/max9850.c new file +2
-0+/* enable charge pump, disable everything else */ +snd_soc_write (codec,MAX9850_ENABLE ,0x30 );
This sounds like it should be in either bias management or DAPM.
sound/soc/codecs/max9850.c line 276
Quoted 4 lines
sound/soc/codecs/max9850.c new file +4
-0+/* enable slew-rate control */ +snd_soc_update_bits (codec,MAX9850_VOLUME ,0x40 ,0x40 ); +/* set slew-rate 125ms */ +snd_soc_update_bits (codec,MAX9850_CHARGE_PUMP ,0xff ,0xc0 );
If this is for the charge pump this is fine but the _VOLUME makes it sound like this should perhaps be user visibile?
sound/soc/codecs/max9850.c line 290
Quoted 4 lines
sound/soc/codecs/max9850.c new file +4
-0+static int max9850_remove (struct snd_soc_codec *codec) +{ +return 0 ; +}
Just delete this if not required, all ASoC functions should be optional.
Quoted 22 lines · Mark Brown
Quoted 5 lines · Christian Glindkamp
sound/soc/codecs/max9850.c new file +5
-0+static int max9850_set_bias_level (struct snd_soc_codec *codec, +enum snd_soc_bias_level level) +{ +switch (level) { +case SND_SOC_BIAS_ON :sound/soc/codecs/max9850.c line 229
Quoted 10 lines
sound/soc/codecs/max9850.c new file +10
-0+break ; +case SND_SOC_BIAS_PREPARE : +snd_soc_update_bits (codec,MAX9850_ENABLE ,MAX9850_SHDN , +MAX9850_SHDN ); +break ; +case SND_SOC_BIAS_STANDBY : +snd_soc_update_bits (codec,MAX9850_ENABLE ,MAX9850_SHDN ,0 ); +break ; +case SND_SOC_BIAS_OFF : +break ;This pattern looks awfully like you should set
idle_bias_offfor the CODEC and then move the code blocks down one power level -_SHDNsounds like a general power down for the device which fits better with the_OFFstate.
Quoted 1 line
Or use DAPM like Dimitris suggested.
I've done so, because it seemed that after the first use, the codec is hold in standby (when not entering suspend) for the whole time. So I thought by moving shutdown to standby might save some milliamps. But I think I will go the DAPM route.
Quoted 7 lines
sound/soc/codecs/max9850.c line 276
Quoted 4 lines
sound/soc/codecs/max9850.c new file +4
-0+/* enable slew-rate control */ +snd_soc_update_bits (codec,MAX9850_VOLUME ,0x40 ,0x40 ); +/* set slew-rate 125ms */ +snd_soc_update_bits (codec,MAX9850_CHARGE_PUMP ,0xff ,0xc0 );If this is for the charge pump this is fine but the
_VOLUMEmakes it sound like this should perhaps be user visibile?
These bits control, whether the volume is set immediately or smoothly slewn between levels. I don't see a real reason a user would want to change it.
Quoted 7 lines
sound/soc/codecs/max9850.c line 290
Quoted 5 lines
sound/soc/codecs/max9850.c new file +4
-0+static int max9850_remove (struct snd_soc_codec *codec) +{ +return 0 ; +}Just delete this if not required, all ASoC functions should be optional.
Will do this, even though Dimitris suggested setting the bias level to off, because it would still be a nop.
Hi,
Quoted 37 lines
sound/soc/codecs/max9850.h new file +31
-0@@ -0,0 +1,41 @@ +/* +* max9850.h -- codec driver for max9850 +* +* Copyright (C) 2011 taskit GmbH +* Author: Christian Glindkamp <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +* +*/ + +#ifndef _MAX9850_H +#define _MAX9850_H + +#define MAX9850_STATUSA 0x00 +#define MAX9850_STATUSB 0x01 +#define MAX9850_VOLUME 0x02 +#define MAX9850_GENERAL_PURPOSE 0x03 +#define MAX9850_INTERRUPT 0x04 +#define MAX9850_ENABLE 0x05 +#define MAX9850_CLOCK 0x06 +#define MAX9850_CHARGE_PUMP 0x07 +#define MAX9850_LRCLK_MSB 0x08 +#define MAX9850_LRCLK_LSB 0x09 +#define MAX9850_DIGITAL_AUDIO 0x0a + +#define MAX9850_CACHEREGNUM 11 + +/* MAX9850_ENABLE */
sound/soc/codecs/max9850.h line 41
Quoted 10 lines
sound/soc/codecs/max9850.h new file +10
-0+#define MAX9850_SHDN (1<<7) + +/* MAX9850_DIGITAL_AUDIO */ +#define MAX9850_MASTER (1<<7) +#define MAX9850_INV (1<<6) +#define MAX9850_BCINV (1<<5) +#define MAX9850_DLY (1<<3) +#define MAX9850_RTJ (1<<2) + +#endif
IMHO, because of MAX9850_* macros are only using inside max9850.c, I think that move MAX9850_* macros into max9850.c and remove max9850.h header file, is more looks good to me.
_______________________________________________
Alsa-devel mailing list
[email protected]
http://mailman.alsa-project.org/mailman/listinfo/alsa-devel
Quoted 3 lines · Seungwhan Youn
IMHO, because of MAX9850_* macros are only using inside
max9850.c, I think that move MAX9850_* macros intomax9850.cand removemax9850.hheader file, is more looks good to me.
It is common practice to have the register definitions / enumerations in a header file even though they are only used by 1 driver. However, any other type declarations or definitions which are not used by multiple drivers are never put into the header file.
Thanks,
Dimitris
PATCH v2 1/1 ASoC: Add MAX9850 codec driver
In reply to Christian GlindkampThis patch adds ASoC support for the MAX9850 codec with headphone amplifier.
Supported features:
- Playback
- 16, 20 and 24 bit audio
- 8k - 48k sample rates
- DAPM
--- sound/soc/codecs/Kconfig | 4 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/max9850.c | 389 ++++++++++++++++++++++++++++++++++++++++++++ sound/soc/codecs/max9850.h | 38 +++++ 4 files changed, 433 insertions(+), 0 deletions(-) create mode 100644 sound/soc/codecs/max9850.c create mode 100644 sound/soc/codecs/max9850.h
sound/soc/codecs/Kconfig +4 -0
@@ -33,6 +33,7 @@ config SND_SOC_ALL_CODECS select SND_SOC_JZ4740_CODEC if SOC_JZ4740 select SND_SOC_LM4857 if I2C select SND_SOC_MAX98088 if I2C + select SND_SOC_MAX9850 if I2C select SND_SOC_MAX9877 if I2C select SND_SOC_PCM3008 select SND_SOC_SGTL5000 if I2C
@@ -186,6 +187,9 @@ config SND_SOC_DMIC config SND_SOC_MAX98088 tristate +config SND_SOC_MAX9850 + tristate + config SND_SOC_PCM3008 tristate
sound/soc/codecs/Makefile +2 -0
@@ -19,6 +19,7 @@ snd-soc-dfbmcs320-objs := dfbmcs320.o snd-soc-dmic-objs := dmic.o snd-soc-l3-objs := l3.o snd-soc-max98088-objs := max98088.o +snd-soc-max9850-objs := max9850.o snd-soc-pcm3008-objs := pcm3008.o snd-soc-sgtl5000-objs := sgtl5000.o snd-soc-alc5623-objs := alc5623.o
@@ -107,6 +108,7 @@ obj-$(CONFIG_SND_SOC_DMIC) += snd-soc-dmic.o obj-$(CONFIG_SND_SOC_L3) += snd-soc-l3.o obj-$(CONFIG_SND_SOC_JZ4740_CODEC) += snd-soc-jz4740-codec.o obj-$(CONFIG_SND_SOC_MAX98088) += snd-soc-max98088.o +obj-$(CONFIG_SND_SOC_MAX9850) += snd-soc-max9850.o obj-$(CONFIG_SND_SOC_PCM3008) += snd-soc-pcm3008.o obj-$(CONFIG_SND_SOC_SGTL5000) += snd-soc-sgtl5000.o obj-$(CONFIG_SND_SOC_SN95031) +=snd-soc-sn95031.o
sound/soc/codecs/max9850.c new file +389 -0
389 lines not on this page · raw message
sound/soc/codecs/max9850.h new file +38 -0
@@ -0,0 +1,38 @@ +/* +* max9850.h -- codec driver for max9850 +* +* Copyright (C) 2011 taskit GmbH +* Author: Christian Glindkamp <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +* +*/ + +#ifndef _MAX9850_H +#define _MAX9850_H + +#define MAX9850_STATUSA 0x00 +#define MAX9850_STATUSB 0x01 +#define MAX9850_VOLUME 0x02 +#define MAX9850_GENERAL_PURPOSE 0x03 +#define MAX9850_INTERRUPT 0x04 +#define MAX9850_ENABLE 0x05 +#define MAX9850_CLOCK 0x06 +#define MAX9850_CHARGE_PUMP 0x07 +#define MAX9850_LRCLK_MSB 0x08 +#define MAX9850_LRCLK_LSB 0x09 +#define MAX9850_DIGITAL_AUDIO 0x0a + +#define MAX9850_CACHEREGNUM 11 + +/* MAX9850_DIGITAL_AUDIO */ +#define MAX9850_MASTER (1<<7) +#define MAX9850_INV (1<<6) +#define MAX9850_BCINV (1<<5) +#define MAX9850_DLY (1<<3) +#define MAX9850_RTJ (1<<2) + +#endif
Signature · 1 line
1.7.2.3
Quoted 10 lines · Christian Glindkamp
This patch adds ASoC support for the MAX9850 codec with headphone amplifier.
Supported features:
- Playback
- 16, 20 and 24 bit audio
- 8k - 48k sample rates
- DAPMSigned-off-by Christian Glindkamp <[email protected]>
Looks good.
Thanks,
Dimitris
Quoted 10 lines · Christian Glindkamp
This patch adds ASoC support for the MAX9850 codec with headphone amplifier.
Supported features:
- Playback
- 16, 20 and 24 bit audio
- 8k - 48k sample rates
- DAPMSigned-off-by Christian Glindkamp <[email protected]>
Two minor comments below, the first can be fixed incrementally. The second is not urgent but will be useful when this driver is used on different devices.
Quoted 168 lines
--- sound/soc/codecs/Kconfig | 4 + sound/soc/codecs/Makefile | 2 + sound/soc/codecs/max9850.c | 389 ++++++++++++++++++++++++++++++++++++++++++++ sound/soc/codecs/max9850.h | 38 +++++ 4 files changed, 433 insertions(+), 0 deletions(-) create mode 100644 sound/soc/codecs/max9850.c create mode 100644 sound/soc/codecs/max9850.hsound/soc/codecs/Kconfig +4
-0@@ -33,6 +33,7 @@ config SND_SOC_ALL_CODECS select SND_SOC_JZ4740_CODEC if SOC_JZ4740 select SND_SOC_LM4857 if I2C select SND_SOC_MAX98088 if I2C + select SND_SOC_MAX9850 if I2C select SND_SOC_MAX9877 if I2C select SND_SOC_PCM3008 select SND_SOC_SGTL5000 if I2C@@ -186,6 +187,9 @@ config SND_SOC_DMIC config SND_SOC_MAX98088 tristate +config SND_SOC_MAX9850 + tristate + config SND_SOC_PCM3008 tristatesound/soc/codecs/Makefile +2
-0@@ -19,6 +19,7 @@ snd-soc-dfbmcs320-objs := dfbmcs320.o snd-soc-dmic-objs := dmic.o snd-soc-l3-objs := l3.o snd-soc-max98088-objs := max98088.o +snd-soc-max9850-objs := max9850.o snd-soc-pcm3008-objs := pcm3008.o snd-soc-sgtl5000-objs := sgtl5000.o snd-soc-alc5623-objs := alc5623.o@@ -107,6 +108,7 @@ obj-$(CONFIG_SND_SOC_DMIC) += snd-soc-dmic.o obj-$(CONFIG_SND_SOC_L3) += snd-soc-l3.o obj-$(CONFIG_SND_SOC_JZ4740_CODEC) += snd-soc-jz4740-codec.o obj-$(CONFIG_SND_SOC_MAX98088) += snd-soc-max98088.o +obj-$(CONFIG_SND_SOC_MAX9850) += snd-soc-max9850.o obj-$(CONFIG_SND_SOC_PCM3008) += snd-soc-pcm3008.o obj-$(CONFIG_SND_SOC_SGTL5000) += snd-soc-sgtl5000.o obj-$(CONFIG_SND_SOC_SN95031) +=snd-soc-sn95031.osound/soc/codecs/max9850.c new file +111
-0@@ -0,0 +1,389 @@ +/* +* max9850.c -- codec driver for max9850 +* +* Copyright (C) 2011 taskit GmbH +* +* Author: Christian Glindkamp <[email protected]> +* +* Initial development of this code was funded by +* MICRONIC Computer Systeme GmbH, http://www.mcsberlin.de/ +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +* +*/ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/i2c.h> +#include <linux/slab.h> +#include <sound/pcm.h> +#include <sound/pcm_params.h> +#include <sound/soc.h> +#include <sound/tlv.h> + +#include "max9850.h" + +struct max9850_priv { +unsigned int sysclk; +}; + +/* max9850 register cache */ +static const u8 max9850_reg[MAX9850_CACHEREGNUM ] = { +0x00 ,0x00 ,0x0c ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 ,0x00 +}; + +/* these registers are not used at the moment but provided for the sake of +* completeness */ +static int max9850_volatile_register (struct snd_soc_codec *codec, +unsigned int reg) +{ +switch (reg) { +case MAX9850_STATUSA : +case MAX9850_STATUSB : +return 1 ; +default : +return 0 ; + } +} + +static const unsigned int max9850_tlv[] = { +TLV_DB_RANGE_HEAD (4 ), +0x18 ,0x1f ,TLV_DB_SCALE_ITEM (-7450 ,400 ,0 ), +0x20 ,0x33 ,TLV_DB_SCALE_ITEM (-4150 ,200 ,0 ), +0x34 ,0x37 ,TLV_DB_SCALE_ITEM (-150 ,100 ,0 ), +0x38 ,0x3f ,TLV_DB_SCALE_ITEM (250 ,50 ,0 ), +}; + +static const struct snd_kcontrol_new max9850_controls[] = { +SOC_SINGLE_TLV ("Headphone Volume" ,MAX9850_VOLUME ,0 ,0x3f ,1 , max9850_tlv), +SOC_SINGLE ("Headphone Switch" ,MAX9850_VOLUME ,7 ,1 ,1 ), +SOC_SINGLE ("Mono Switch" ,MAX9850_GENERAL_PURPOSE ,2 ,1 ,0 ), +}; + +static const struct snd_kcontrol_new max9850_mixer_controls[] = { +SOC_DAPM_SINGLE ("Line In Switch" ,MAX9850_ENABLE ,1 ,1 ,0 ), +}; + +static const struct snd_soc_dapm_widget max9850_dapm_widgets[] = { +SND_SOC_DAPM_SUPPLY ("Charge Pump 1" ,MAX9850_ENABLE ,4 ,0 ,NULL ,0 ), +SND_SOC_DAPM_SUPPLY ("Charge Pump 2" ,MAX9850_ENABLE ,5 ,0 ,NULL ,0 ), +SND_SOC_DAPM_SUPPLY ("MCLK" ,MAX9850_ENABLE ,6 ,0 ,NULL ,0 ), +SND_SOC_DAPM_SUPPLY ("SHDN" ,MAX9850_ENABLE ,7 ,0 ,NULL ,0 ), +SND_SOC_DAPM_MIXER_NAMED_CTL ("Output Mixer" ,MAX9850_ENABLE ,2 ,0 , + &max9850_mixer_controls[0 ], +ARRAY_SIZE (max9850_mixer_controls)), +SND_SOC_DAPM_PGA ("Headphone Output" ,MAX9850_ENABLE ,3 ,0 ,NULL ,0 ), +SND_SOC_DAPM_DAC ("DAC" ,"HiFi Playback" ,MAX9850_ENABLE ,0 ,0 ), +SND_SOC_DAPM_OUTPUT ("OUTL" ), +SND_SOC_DAPM_OUTPUT ("HPL" ), +SND_SOC_DAPM_OUTPUT ("OUTR" ), +SND_SOC_DAPM_OUTPUT ("HPR" ), +SND_SOC_DAPM_MIXER ("Line Input" ,SND_SOC_NOPM ,0 ,0 ,NULL ,0 ), +SND_SOC_DAPM_INPUT ("INL" ), +SND_SOC_DAPM_INPUT ("INR" ), +}; + +static const struct snd_soc_dapm_route intercon[] = { +/* output mixer */ + {"Output Mixer" ,NULL ,"DAC" }, + {"Output Mixer" ,"Line In Switch" ,"Line Input" }, + +/* outputs */ + {"Headphone Output" ,NULL ,"Output Mixer" }, + {"HPL" ,NULL ,"Headphone Output" }, + {"HPR" ,NULL ,"Headphone Output" }, + {"OUTL" ,NULL ,"Output Mixer" }, + {"OUTR" ,NULL ,"Output Mixer" }, + +/* inputs */ + {"Line Input" ,NULL ,"INL" }, + {"Line Input" ,NULL ,"INR" }, + +/* supplies */ + {"Output Mixer" ,NULL ,"Charge Pump 1" }, + {"Output Mixer" ,NULL ,"Charge Pump 2" }, + {"Output Mixer" ,NULL ,"SHDN" }, + {"DAC" ,NULL ,"MCLK" }, +}; +
sound/soc/codecs/max9850.c line 121
Quoted 10 lines
sound/soc/codecs/max9850.c new file +10
-0+static int max9850_hw_params (struct snd_pcm_substream *substream, +struct snd_pcm_hw_params *params, +struct snd_soc_dai *dai) +{ +struct snd_soc_codec *codec = dai->codec; +struct max9850_priv *max9850 =snd_soc_codec_get_drvdata (codec); +u64 lrclk_div; +u8 sf, da; + +if (!max9850->sysclk)
space after if
Quoted 180 lines
sound/soc/codecs/max9850.c new file +180
-0+return -EINVAL ; + +/* lrclk_div = 2^22 * rate / iclk with iclk = mclk / sf */ + sf = (snd_soc_read (codec,MAX9850_CLOCK ) >>2 ) +1 ; + lrclk_div = (1 <<22 ); + lrclk_div *=params_rate (params); + lrclk_div *= sf; +do_div (lrclk_div, max9850->sysclk); + +snd_soc_write (codec,MAX9850_LRCLK_MSB , (lrclk_div >>8 ) &0x7f ); +snd_soc_write (codec,MAX9850_LRCLK_LSB , lrclk_div &0xff ); + +switch (params_format (params)) { +case SNDRV_PCM_FORMAT_S16_LE : + da =0 ; +break ; +case SNDRV_PCM_FORMAT_S20_3LE : + da =0x2 ; +break ; +case SNDRV_PCM_FORMAT_S24_LE : + da =0x3 ; +break ; +default : +return -EINVAL ; + } +snd_soc_update_bits (codec,MAX9850_DIGITAL_AUDIO ,0x3 , da); + +return 0 ; +} + +static int max9850_set_dai_sysclk (struct snd_soc_dai *codec_dai, +int clk_id,unsigned int freq,int dir) +{ +struct snd_soc_codec *codec = codec_dai->codec; +struct max9850_priv *max9850 =snd_soc_codec_get_drvdata (codec); + +/* calculate mclk -> iclk divider */ +if (freq <=13000000 ) +snd_soc_write (codec,MAX9850_CLOCK ,0x0 ); +else if (freq <=26000000 ) +snd_soc_write (codec,MAX9850_CLOCK ,0x4 ); +else if (freq <=40000000 ) +snd_soc_write (codec,MAX9850_CLOCK ,0x8 ); +else +return -EINVAL ; + + max9850->sysclk = freq; +return 0 ; +} + +static int max9850_set_dai_fmt (struct snd_soc_dai *codec_dai,unsigned int fmt) +{ +struct snd_soc_codec *codec = codec_dai->codec; +u8 da =0 ; + +/* set master/slave audio interface */ +switch (fmt &SND_SOC_DAIFMT_MASTER_MASK ) { +case SND_SOC_DAIFMT_CBM_CFM : + da |=MAX9850_MASTER ; +break ; +case SND_SOC_DAIFMT_CBS_CFS : +break ; +default : +return -EINVAL ; + } + +/* interface format */ +switch (fmt &SND_SOC_DAIFMT_FORMAT_MASK ) { +case SND_SOC_DAIFMT_I2S : + da |=MAX9850_DLY ; +break ; +case SND_SOC_DAIFMT_RIGHT_J : + da |=MAX9850_RTJ ; +break ; +case SND_SOC_DAIFMT_LEFT_J : +break ; +default : +return -EINVAL ; + } + +/* clock inversion */ +switch (fmt &SND_SOC_DAIFMT_INV_MASK ) { +case SND_SOC_DAIFMT_NB_NF : +break ; +case SND_SOC_DAIFMT_IB_IF : + da |=MAX9850_BCINV |MAX9850_INV ; +break ; +case SND_SOC_DAIFMT_IB_NF : + da |=MAX9850_BCINV ; +break ; +case SND_SOC_DAIFMT_NB_IF : + da |=MAX9850_INV ; +break ; +default : +return -EINVAL ; + } + +/* set da */ +snd_soc_write (codec,MAX9850_DIGITAL_AUDIO , da); + +return 0 ; +} + +static int max9850_set_bias_level (struct snd_soc_codec *codec, +enum snd_soc_bias_level level) +{ +int ret; + +switch (level) { +case SND_SOC_BIAS_ON : +break ; +case SND_SOC_BIAS_PREPARE : +break ; +case SND_SOC_BIAS_STANDBY : +if (codec->dapm.bias_level ==SND_SOC_BIAS_OFF ) { + ret =snd_soc_cache_sync (codec); +if (ret) { +dev_err (codec->dev, +"Failed to sync cache: %d\n" , ret); +return ret; + } + } +break ; +case SND_SOC_BIAS_OFF : +break ; + } + codec->dapm.bias_level = level; +return 0 ; +} + +#define MAX9850_RATES SNDRV_PCM_RATE_8000_48000 + +#define MAX9850_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE |\ + SNDRV_PCM_FMTBIT_S24_LE) + +static struct snd_soc_dai_ops max9850_dai_ops = { + .hw_params = max9850_hw_params, + .set_sysclk = max9850_set_dai_sysclk, + .set_fmt = max9850_set_dai_fmt, +}; + +static struct snd_soc_dai_driver max9850_dai = { + .name ="max9850-hifi" , + .playback = { + .stream_name ="Playback" , + .channels_min =1 , + .channels_max =2 , + .rates =MAX9850_RATES , + .formats =MAX9850_FORMATS + }, + .ops = &max9850_dai_ops, +}; + +#ifdef CONFIG_PM +static int max9850_suspend (struct snd_soc_codec *codec,pm_message_t state) +{ +max9850_set_bias_level (codec,SND_SOC_BIAS_OFF ); + +return 0 ; +} + +static int max9850_resume (struct snd_soc_codec *codec) +{ +max9850_set_bias_level (codec,SND_SOC_BIAS_STANDBY ); + +return 0 ; +} +#else +#define max9850_suspend NULL +#define max9850_resume NULL +#endif + +static int max9850_probe (struct snd_soc_codec *codec) +{ +struct snd_soc_dapm_context *dapm = &codec->dapm; +int ret; + + ret =snd_soc_codec_set_cache_io (codec,8 ,8 ,SND_SOC_I2C ); +if (ret <0 ) { +dev_err (codec->dev,"Failed to set cache I/O: %d\n" , ret);
sound/soc/codecs/max9850.c line 311
Quoted 10 lines
sound/soc/codecs/max9850.c new file +10
-0+return ret; + } + +/* enable zero-detect */ +snd_soc_update_bits (codec,MAX9850_GENERAL_PURPOSE ,1 ,1 ); +/* enable slew-rate control */ +snd_soc_update_bits (codec,MAX9850_VOLUME ,0x40 ,0x40 ); +/* set slew-rate 125ms */ +snd_soc_update_bits (codec,MAX9850_CHARGE_PUMP ,0xff ,0xc0 ); +
Things like slew rate are often better configured with platform data.
Quoted 122 lines
sound/soc/codecs/max9850.c new file +78
-0+snd_soc_dapm_new_controls (dapm, max9850_dapm_widgets, +ARRAY_SIZE (max9850_dapm_widgets)); +snd_soc_dapm_add_routes (dapm, intercon,ARRAY_SIZE (intercon)); + +snd_soc_add_controls (codec, max9850_controls, +ARRAY_SIZE (max9850_controls)); + +return 0 ; +} + +static struct snd_soc_codec_driver soc_codec_dev_max9850 = { + .probe = max9850_probe, + .suspend = max9850_suspend, + .resume = max9850_resume, + .set_bias_level = max9850_set_bias_level, + .reg_cache_size =ARRAY_SIZE (max9850_reg), + .reg_word_size =sizeof (u8), + .reg_cache_default = max9850_reg, + .volatile_register = max9850_volatile_register, +}; + +static int __devinit max9850_i2c_probe (struct i2c_client *i2c, +const struct i2c_device_id *id) +{ +struct max9850_priv *max9850; +int ret; + + max9850 =kzalloc (sizeof (struct max9850_priv ),GFP_KERNEL ); +if (max9850 ==NULL ) +return -ENOMEM ; + +i2c_set_clientdata (i2c, max9850); + + ret =snd_soc_register_codec (&i2c->dev, + &soc_codec_dev_max9850, &max9850_dai,1 ); +if (ret <0 ) +kfree (max9850); +return ret; +} + +static __devexit int max9850_i2c_remove(struct i2c_client *client) +{ +snd_soc_unregister_codec (&client->dev); +kfree (i2c_get_clientdata (client)); +return 0 ; +} + +static const struct i2c_device_id max9850_i2c_id[] = { + {"max9850" ,0 }, + { } +}; +MODULE_DEVICE_TABLE (i2c, max9850_i2c_id); + +static struct i2c_driver max9850_i2c_driver = { + .driver = { + .name ="max9850" , + .owner =THIS_MODULE , + }, + .probe = max9850_i2c_probe, + .remove =__devexit_p (max9850_i2c_remove), + .id_table = max9850_i2c_id, +}; + +static int __init max9850_init (void ) +{ +return i2c_add_driver (&max9850_i2c_driver); +} +module_init (max9850_init); + +static void __exit max9850_exit(void) +{ +i2c_del_driver (&max9850_i2c_driver); +} +module_exit (max9850_exit); + +MODULE_AUTHOR ("Christian Glindkamp <[email protected]>" ); +MODULE_DESCRIPTION ("ASoC MAX9850 codec driver" ); +MODULE_LICENSE ("GPL" );sound/soc/codecs/max9850.h new file +38
-0@@ -0,0 +1,38 @@ +/* +* max9850.h -- codec driver for max9850 +* +* Copyright (C) 2011 taskit GmbH +* Author: Christian Glindkamp <[email protected]> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +* +*/ + +#ifndef _MAX9850_H +#define _MAX9850_H + +#define MAX9850_STATUSA 0x00 +#define MAX9850_STATUSB 0x01 +#define MAX9850_VOLUME 0x02 +#define MAX9850_GENERAL_PURPOSE 0x03 +#define MAX9850_INTERRUPT 0x04 +#define MAX9850_ENABLE 0x05 +#define MAX9850_CLOCK 0x06 +#define MAX9850_CHARGE_PUMP 0x07 +#define MAX9850_LRCLK_MSB 0x08 +#define MAX9850_LRCLK_LSB 0x09 +#define MAX9850_DIGITAL_AUDIO 0x0a + +#define MAX9850_CACHEREGNUM 11 + +/* MAX9850_DIGITAL_AUDIO */ +#define MAX9850_MASTER (1<<7) +#define MAX9850_INV (1<<6) +#define MAX9850_BCINV (1<<5) +#define MAX9850_DLY (1<<3) +#define MAX9850_RTJ (1<<2) + +#endif
Mark Brown
AppliedQuoted 2 lines · Christian Glindkamp
This patch adds ASoC support for the MAX9850 codec with headphone amplifier.
Applied, thanks. I also added a commit fixing up the formatting error Liam mentioned.