add more features for mtk-star-emac
Subsystems (5)
v2 cover add more features for mtk-star-emac
Changes in v2:
1. fix coding style as Bartosz's comments.
2. add reviewed-by as Bartosz's comments.
This series add more features for mtk-star-emac:
1. add reference clock pad selection for RMII;
2. add simple timing adjustment for RMII;
3. add support for MII;
4. add support for new IC MT8365;
5. separate tx/rx interrupt handling.
Biao Huang (8):
net: ethernet: mtk-star-emac: modify IRQ trigger flags
net: ethernet: mtk-star-emac: add support for MT8365 SoC
dt-bindings: net: mtk-star-emac: add support for MT8365
net: ethernet: mtk-star-emac: add clock pad selection for RMII
net: ethernet: mtk-star-emac: add timing adjustment support
dt-bindings: net: mtk-star-emac: add description for new properties
net: ethernet: mtk-star-emac: add support for MII interface
net: ethernet: mtk-star-emac: separate tx/rx handling with two NAPIs
Fabien Parent (1):
net: ethernet: mtk-star-emac: store bit_clk_div in compat structure
.../bindings/net/mediatek,star-emac.yaml | 17 + drivers/net/ethernet/mediatek/mtk_star_emac.c | 477 ++++++++++++------ 2 files changed, 341 insertions(+), 153 deletions(-)
Signature · 1 line
2.25.1
PATCH v2 1/9 net: ethernet: mtk-star-emac: store bit_clk_div in compat structure
From: Fabien Parent <[email protected]>
Not all the SoC are using the same clock divider. Move the divider into a compat structure specific to the SoCs.
--- drivers/net/ethernet/mediatek/mtk_star_emac.c | 23 +++++++++++++++---- 1 file changed, 19 insertions(+), 4 deletions(-)
drivers/net/ethernet/mediatek/mtk_star_emac.c +19 -4
@@ -17,6 +17,7 @@#include <linux/module.h> #include <linux/netdevice.h> #include <linux/of.h> +#include <linux/of_device.h> #include <linux/of_mdio.h> #include <linux/of_net.h> #include <linux/platform_device.h>
@@ -232,6 +233,10 @@ struct mtk_star_ring {unsigned int tail; }; +struct mtk_star_compat { +unsigned char bit_clk_div; +}; +struct mtk_star_priv {struct net_device *ndev;
@@ -257,6 +262,8 @@ struct mtk_star_priv {int duplex;int pause; +const struct mtk_star_compat *compat_data; +/* Protects against concurrent descriptor access. */ spinlock_t lock;
@@ -899,7 +906,7 @@ static void mtk_star_init_config(struct mtk_star_priv *priv)regmap_write (priv->regs,MTK_STAR_REG_SYS_CONF , val);regmap_update_bits (priv->regs,MTK_STAR_REG_MAC_CLK_CONF ,MTK_STAR_MSK_MAC_CLK_CONF , -MTK_STAR_BIT_CLK_DIV_10 ); + priv->compat_data->bit_clk_div); }static void mtk_star_set_mode_rmii (struct mtk_star_priv *priv)
@@ -1461,6 +1468,7 @@ static int mtk_star_probe(struct platform_device *pdev) priv =netdev_priv (ndev); priv->ndev = ndev; + priv->compat_data =of_device_get_match_data (&pdev->dev);SET_NETDEV_DEV (ndev, dev);platform_set_drvdata (pdev, ndev);
@@ -1556,10 +1564,17 @@ static int mtk_star_probe(struct platform_device *pdev)return devm_register_netdev (dev, ndev); } +static const struct mtk_star_compat mtk_star_mt8516_compat = { + .bit_clk_div =MTK_STAR_BIT_CLK_DIV_10 , +}; +static const struct of_device_id mtk_star_of_match[] = { - { .compatible ="mediatek,mt8516-eth" , }, - { .compatible ="mediatek,mt8518-eth" , }, - { .compatible ="mediatek,mt8175-eth" , }, + { .compatible ="mediatek,mt8516-eth" , + .data = &mtk_star_mt8516_compat }, + { .compatible ="mediatek,mt8518-eth" , + .data = &mtk_star_mt8516_compat }, + { .compatible ="mediatek,mt8175-eth" , + .data = &mtk_star_mt8516_compat }, { } };MODULE_DEVICE_TABLE (of, mtk_star_of_match);
Signature · 1 line
2.25.1
Re: [PATCH net-next v2 1/9] net: ethernet: mtk-star-emac: store bit_clk_div in compat structure
Quoted 72 lines · Biao Huang
From: Fabien Parent <[email protected]>
Not all the SoC are using the same clock divider. Move the divider into a compat structure specific to the SoCs.
Signed-off-by Biao Huang <[email protected]>Signed-off-by Fabien Parent <[email protected]>--- drivers/net/ethernet/mediatek/mtk_star_emac.c | 23 +++++++++++++++---- 1 file changed, 19 insertions(+), 4 deletions(-)drivers/net/ethernet/mediatek/mtk_star_emac.c +13
-3@@ -17,6 +17,7 @@#include <linux/module.h> #include <linux/netdevice.h> #include <linux/of.h> +#include <linux/of_device.h> #include <linux/of_mdio.h> #include <linux/of_net.h> #include <linux/platform_device.h> @@ -232,6 +233,10 @@ struct mtk_star_ring {unsigned int tail; }; +struct mtk_star_compat { +unsigned char bit_clk_div; +}; +struct mtk_star_priv {struct net_device *ndev;@@ -257,6 +262,8 @@ struct mtk_star_priv {int duplex;int pause; +const struct mtk_star_compat *compat_data; +/* Protects against concurrent descriptor access. */ spinlock_t lock;@@ -899,7 +906,7 @@ static void mtk_star_init_config(struct mtk_star_priv *priv)regmap_write (priv->regs,MTK_STAR_REG_SYS_CONF , val);regmap_update_bits (priv->regs,MTK_STAR_REG_MAC_CLK_CONF ,MTK_STAR_MSK_MAC_CLK_CONF , -MTK_STAR_BIT_CLK_DIV_10 ); + priv->compat_data->bit_clk_div); }static void mtk_star_set_mode_rmii (struct mtk_star_priv *priv)@@ -1461,6 +1468,7 @@ static int mtk_star_probe(struct platform_device *pdev) priv =netdev_priv (ndev); priv->ndev = ndev; + priv->compat_data =of_device_get_match_data (&pdev->dev);SET_NETDEV_DEV (ndev, dev);platform_set_drvdata (pdev, ndev);@@ -1556,10 +1564,17 @@ static int mtk_star_probe(struct platform_device *pdev)return devm_register_netdev (dev, ndev); } +static const struct mtk_star_compat mtk_star_mt8516_compat = { + .bit_clk_div =MTK_STAR_BIT_CLK_DIV_10 , +}; +static const struct of_device_id mtk_star_of_match[] = { - { .compatible ="mediatek,mt8516-eth" , }, - { .compatible ="mediatek,mt8518-eth" , },
drivers/net/ethernet/mediatek/mtk_star_emac.c static int mtk_star_probe(struct platform_device *pdev) · line 1580
Quoted 10 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +6
-1- { .compatible = "mediatek,mt8175-eth", }, + { .compatible = "mediatek,mt8516-eth", + .data = &mtk_star_mt8516_compat }, + { .compatible = "mediatek,mt8518-eth", + .data = &mtk_star_mt8516_compat }, + { .compatible = "mediatek,mt8175-eth", + .data = &mtk_star_mt8516_compat }, { } };MODULE_DEVICE_TABLE (of, mtk_star_of_match);
Regards,
Macpaul Lin
PATCH v2 2/9 net: ethernet: mtk-star-emac: modify IRQ trigger flags
In reply to Biao HuangIf the flags in request_irq() is IRQF_TRIGGER_NONE, the trigger method is determined by "interrupt" property in dts.
So, modify the flag from IRQF_TRIGGER_FALLING to IRQF_TRIGGER_NONE.
--- drivers/net/ethernet/mediatek/mtk_star_emac.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/net/ethernet/mediatek/mtk_star_emac.c +1 -1
@@ -959,7 +959,7 @@ static int mtk_star_enable(struct net_device *ndev)/* Request the interrupt */ ret =request_irq (ndev->irq, mtk_star_handle_irq, -IRQF_TRIGGER_FALLING , ndev->name, ndev); +IRQF_TRIGGER_NONE , ndev->name, ndev);if (ret) goto err_free_skbs;
Signature · 1 line
2.25.1
PATCH v2 3/9 net: ethernet: mtk-star-emac: add support for MT8365 SoC
In reply to Biao HuangAdd Ethernet driver support for MT8365 SoC.
--- drivers/net/ethernet/mediatek/mtk_star_emac.c | 75 ++++++++++++++++--- 1 file changed, 64 insertions(+), 11 deletions(-)
drivers/net/ethernet/mediatek/mtk_star_emac.c +64 -11
@@ -151,6 +151,7 @@ static const char *const mtk_star_clk_names[] = { "core", "reg", "trans" };#define MTK_STAR_REG_MAC_CLK_CONF 0x00ac#define MTK_STAR_MSK_MAC_CLK_CONF GENMASK(7, 0)#define MTK_STAR_BIT_CLK_DIV_10 0x0a +#define MTK_STAR_BIT_CLK_DIV_50 0x32/* Counter registers. */ #define MTK_STAR_REG_C_RXOKPKT 0x0100
@@ -183,9 +184,11 @@ static const char *const mtk_star_clk_names[] = { "core", "reg", "trans" };#define MTK_STAR_REG_C_RX_TWIST 0x0218/* Ethernet CFG Control */ -#define MTK_PERICFG_REG_NIC_CFG_CON 0x03c4 -#define MTK_PERICFG_MSK_NIC_CFG_CON_CFG_MII GENMASK(3, 0) -#define MTK_PERICFG_BIT_NIC_CFG_CON_RMII BIT(0) +#define MTK_PERICFG_REG_NIC_CFG0_CON 0x03c4 +#define MTK_PERICFG_REG_NIC_CFG1_CON 0x03c8 +#define MTK_PERICFG_REG_NIC_CFG_CON_V2 0x0c10 +#define MTK_PERICFG_REG_NIC_CFG_CON_CFG_INTF GENMASK(3, 0) +#define MTK_PERICFG_BIT_NIC_CFG_CON_RMII 1/* Represents the actual structure of descriptors used by the MAC. We can * reuse the same structure for both TX and RX - the layout is the same, only
@@ -234,6 +237,7 @@ struct mtk_star_ring { };struct mtk_star_compat { +int (*set_interface_mode)(struct net_device *ndev);unsigned char bit_clk_div; };
@@ -909,13 +913,6 @@ static void mtk_star_init_config(struct mtk_star_priv *priv) priv->compat_data->bit_clk_div); } -static void mtk_star_set_mode_rmii (struct mtk_star_priv *priv) -{ -regmap_update_bits (priv->pericfg,MTK_PERICFG_REG_NIC_CFG_CON , -MTK_PERICFG_MSK_NIC_CFG_CON_CFG_MII , -MTK_PERICFG_BIT_NIC_CFG_CON_RMII ); -} -static int mtk_star_enable (struct net_device *ndev) {struct mtk_star_priv *priv =netdev_priv (ndev);
@@ -1531,7 +1528,13 @@ static int mtk_star_probe(struct platform_device *pdev)return -ENODEV ; } -mtk_star_set_mode_rmii (priv); +if (priv->compat_data->set_interface_mode) { + ret = priv->compat_data->set_interface_mode (ndev); +if (ret) { +dev_err (dev,"Failed to set phy interface, err = %d\n" , ret); +return -EINVAL ; + } + } ret =dma_set_mask_and_coherent (dev,DMA_BIT_MASK (32 ));if (ret) {
@@ -1564,10 +1567,58 @@ static int mtk_star_probe(struct platform_device *pdev)return devm_register_netdev (dev, ndev); } +static int mt8516_set_interface_mode (struct net_device *ndev) +{ +struct mtk_star_priv *priv =netdev_priv (ndev); +struct device *dev =mtk_star_get_dev (priv); +unsigned int intf_val; + +switch (priv->phy_intf) { +case PHY_INTERFACE_MODE_RMII : + intf_val =MTK_PERICFG_BIT_NIC_CFG_CON_RMII ; +break ; +default : +dev_err (dev,"This interface not supported\n" ); +return -EINVAL ; + } + +return regmap_update_bits (priv->pericfg, +MTK_PERICFG_REG_NIC_CFG0_CON , +MTK_PERICFG_REG_NIC_CFG_CON_CFG_INTF , + intf_val); +} + +static int mt8365_set_interface_mode (struct net_device *ndev) +{ +struct mtk_star_priv *priv =netdev_priv (ndev); +struct device *dev =mtk_star_get_dev (priv); +unsigned int intf_val; + +switch (priv->phy_intf) { +case PHY_INTERFACE_MODE_RMII : + intf_val =MTK_PERICFG_BIT_NIC_CFG_CON_RMII ; +break ; +default : +dev_err (dev,"This interface not supported\n" ); +return -EINVAL ; + } + +return regmap_update_bits (priv->pericfg, +MTK_PERICFG_REG_NIC_CFG_CON_V2 , +MTK_PERICFG_REG_NIC_CFG_CON_CFG_INTF , + intf_val); +} +static const struct mtk_star_compat mtk_star_mt8516_compat = { + .set_interface_mode = mt8516_set_interface_mode, .bit_clk_div =MTK_STAR_BIT_CLK_DIV_10 , }; +static const struct mtk_star_compat mtk_star_mt8365_compat = { + .set_interface_mode = mt8365_set_interface_mode, + .bit_clk_div =MTK_STAR_BIT_CLK_DIV_50 , +}; +static const struct of_device_id mtk_star_of_match[] = { { .compatible ="mediatek,mt8516-eth" , .data = &mtk_star_mt8516_compat },
@@ -1575,6 +1626,8 @@ static const struct of_device_id mtk_star_of_match[] = { .data = &mtk_star_mt8516_compat }, { .compatible = "mediatek,mt8175-eth", .data = &mtk_star_mt8516_compat }, + { .compatible = "mediatek,mt8365-eth", + .data = &mtk_star_mt8365_compat }, { } };MODULE_DEVICE_TABLE (of, mtk_star_of_match);
Signature · 1 line
2.25.1
Re: [PATCH net-next v2 3/9] net: ethernet: mtk-star-emac: add support for MT8365 SoC
Quoted 134 lines · Biao Huang
Add Ethernet driver support for MT8365 SoC.
Signed-off-by Biao Huang <[email protected]>Signed-off-by Yinghua Pan <[email protected]>Signed-off-by Fabien Parent <[email protected]>--- drivers/net/ethernet/mediatek/mtk_star_emac.c | 75 ++++++++++++++++--- 1 file changed, 64 insertions(+), 11 deletions(-)drivers/net/ethernet/mediatek/mtk_star_emac.c +62
-11@@ -151,6 +151,7 @@ static const char *const mtk_star_clk_names[] = { "core", "reg", "trans" };#define MTK_STAR_REG_MAC_CLK_CONF 0x00ac#define MTK_STAR_MSK_MAC_CLK_CONF GENMASK(7, 0)#define MTK_STAR_BIT_CLK_DIV_10 0x0a +#define MTK_STAR_BIT_CLK_DIV_50 0x32/* Counter registers. */ #define MTK_STAR_REG_C_RXOKPKT 0x0100@@ -183,9 +184,11 @@ static const char *const mtk_star_clk_names[] = { "core", "reg", "trans" };#define MTK_STAR_REG_C_RX_TWIST 0x0218/* Ethernet CFG Control */ -#define MTK_PERICFG_REG_NIC_CFG_CON 0x03c4 -#define MTK_PERICFG_MSK_NIC_CFG_CON_CFG_MII GENMASK(3, 0) -#define MTK_PERICFG_BIT_NIC_CFG_CON_RMII BIT(0) +#define MTK_PERICFG_REG_NIC_CFG0_CON 0x03c4 +#define MTK_PERICFG_REG_NIC_CFG1_CON 0x03c8 +#define MTK_PERICFG_REG_NIC_CFG_CON_V2 0x0c10 +#define MTK_PERICFG_REG_NIC_CFG_CON_CFG_INTF GENMASK(3, 0) +#define MTK_PERICFG_BIT_NIC_CFG_CON_RMII 1/* Represents the actual structure of descriptors used by the MAC. We can * reuse the same structure for both TX and RX - the layout is the same, only @@ -234,6 +237,7 @@ struct mtk_star_ring { };struct mtk_star_compat { +int (*set_interface_mode)(struct net_device *ndev);unsigned char bit_clk_div; };@@ -909,13 +913,6 @@ static void mtk_star_init_config(struct mtk_star_priv *priv) priv->compat_data->bit_clk_div); } -static void mtk_star_set_mode_rmii (struct mtk_star_priv *priv) -{ -regmap_update_bits (priv->pericfg,MTK_PERICFG_REG_NIC_CFG_CON , -MTK_PERICFG_MSK_NIC_CFG_CON_CFG_MII , -MTK_PERICFG_BIT_NIC_CFG_CON_RMII ); -} -static int mtk_star_enable (struct net_device *ndev) {struct mtk_star_priv *priv =netdev_priv (ndev);@@ -1531,7 +1528,13 @@ static int mtk_star_probe(struct platform_device *pdev)return -ENODEV ; } -mtk_star_set_mode_rmii (priv); +if (priv->compat_data->set_interface_mode) { + ret = priv->compat_data->set_interface_mode (ndev); +if (ret) { +dev_err (dev,"Failed to set phy interface, err = %d\n" , ret); +return -EINVAL ; + } + } ret =dma_set_mask_and_coherent (dev,DMA_BIT_MASK (32 ));if (ret) {@@ -1564,10 +1567,58 @@ static int mtk_star_probe(struct platform_device *pdev)return devm_register_netdev (dev, ndev); } +static int mt8516_set_interface_mode (struct net_device *ndev) +{ +struct mtk_star_priv *priv =netdev_priv (ndev); +struct device *dev =mtk_star_get_dev (priv); +unsigned int intf_val; + +switch (priv->phy_intf) { +case PHY_INTERFACE_MODE_RMII : + intf_val =MTK_PERICFG_BIT_NIC_CFG_CON_RMII ; +break ; +default : +dev_err (dev,"This interface not supported\n" ); +return -EINVAL ; + } + +return regmap_update_bits (priv->pericfg, +MTK_PERICFG_REG_NIC_CFG0_CON , +MTK_PERICFG_REG_NIC_CFG_CON_CFG_INTF , + intf_val); +} + +static int mt8365_set_interface_mode (struct net_device *ndev) +{ +struct mtk_star_priv *priv =netdev_priv (ndev); +struct device *dev =mtk_star_get_dev (priv); +unsigned int intf_val; + +switch (priv->phy_intf) { +case PHY_INTERFACE_MODE_RMII : + intf_val =MTK_PERICFG_BIT_NIC_CFG_CON_RMII ; +break ; +default : +dev_err (dev,"This interface not supported\n" ); +return -EINVAL ; + } + +return regmap_update_bits (priv->pericfg, +MTK_PERICFG_REG_NIC_CFG_CON_V2 , +MTK_PERICFG_REG_NIC_CFG_CON_CFG_INTF , + intf_val); +} +static const struct mtk_star_compat mtk_star_mt8516_compat = { + .set_interface_mode = mt8516_set_interface_mode, .bit_clk_div =MTK_STAR_BIT_CLK_DIV_10 , }; +static const struct mtk_star_compat mtk_star_mt8365_compat = { + .set_interface_mode = mt8365_set_interface_mode, + .bit_clk_div =MTK_STAR_BIT_CLK_DIV_50 , +}; +static const struct of_device_id mtk_star_of_match[] = { { .compatible ="mediatek,mt8516-eth" , .data = &mtk_star_mt8516_compat },
drivers/net/ethernet/mediatek/mtk_star_emac.c static const struct of_device_id mtk_star_of_match[] = { · line 1633
Quoted 8 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +2
-0@@ -1575,6 +1626,8 @@ static const struct of_device_id mtk_star_of_match[] = { .data = &mtk_star_mt8516_compat }, { .compatible = "mediatek,mt8175-eth", .data = &mtk_star_mt8516_compat }, + { .compatible = "mediatek,mt8365-eth", + .data = &mtk_star_mt8365_compat }, { } };MODULE_DEVICE_TABLE (of, mtk_star_of_match);
Regards,
Macpaul Lin
PATCH v2 4/9 dt-bindings: net: mtk-star-emac: add support for MT8365
In reply to Biao HuangAdd binding document for Ethernet on MT8365.
--- Documentation/devicetree/bindings/net/mediatek,star-emac.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/net/mediatek,star-emac.yaml +1 -0
@@ -23,6 +23,7 @@ properties: - mediatek,mt8516-eth - mediatek,mt8518-eth - mediatek,mt8175-eth + - mediatek,mt8365-eth reg: maxItems: 1
Signature · 1 line
2.25.1
Re: [PATCH net-next v2 4/9] dt-bindings: net: mtk-star-emac: add support for MT8365
Quoted 8 lines · Biao Huang
Add binding document for Ethernet on MT8365.
Signed-off-by Biao Huang <[email protected]>Reviewed-by Bartosz Golaszewski <[email protected]>--- Documentation/devicetree/bindings/net/mediatek,star-emac.yaml | 1 + 1 file changed, 1 insertion(+)
_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
PATCH v2 5/9 net: ethernet: mtk-star-emac: add clock pad selection for RMII
In reply to Biao HuangThis patch add a new dts property named "mediatek,rmii-rxc" parsing in driver, which will configure MAC to select which pin the RMII reference clock is connected to, TXC or RXC.
TXC pad is the default reference clock pin. If user wants to use RXC pad instead, add "mediatek,rmii-rxc" to corresponding device node.
--- drivers/net/ethernet/mediatek/mtk_star_emac.c | 19 +++++++++++++++++-- 1 file changed, 17 insertions(+), 2 deletions(-)
drivers/net/ethernet/mediatek/mtk_star_emac.c +17 -2
@@ -189,6 +189,8 @@ static const char *const mtk_star_clk_names[] = { "core", "reg", "trans" };#define MTK_PERICFG_REG_NIC_CFG_CON_V2 0x0c10#define MTK_PERICFG_REG_NIC_CFG_CON_CFG_INTF GENMASK(3, 0)#define MTK_PERICFG_BIT_NIC_CFG_CON_RMII 1 +#define MTK_PERICFG_BIT_NIC_CFG_CON_CLK BIT(0) +#define MTK_PERICFG_BIT_NIC_CFG_CON_CLK_V2 BIT(8)/* Represents the actual structure of descriptors used by the MAC. We can * reuse the same structure for both TX and RX - the layout is the same, only
@@ -265,6 +267,7 @@ struct mtk_star_priv {int speed;int duplex;int pause; +bool rmii_rxc;const struct mtk_star_compat *compat_data;
@@ -1528,6 +1531,8 @@ static int mtk_star_probe(struct platform_device *pdev)return -ENODEV ; } + priv->rmii_rxc =of_property_read_bool (of_node,"mediatek,rmii-rxc" ); +if (priv->compat_data->set_interface_mode) { ret = priv->compat_data->set_interface_mode (ndev);if (ret) {
@@ -1571,17 +1576,25 @@ static int mt8516_set_interface_mode(struct net_device *ndev) {struct mtk_star_priv *priv =netdev_priv (ndev);struct device *dev =mtk_star_get_dev (priv); -unsigned int intf_val; +unsigned int intf_val, ret, rmii_rxc;switch (priv->phy_intf) {case PHY_INTERFACE_MODE_RMII : intf_val =MTK_PERICFG_BIT_NIC_CFG_CON_RMII ; + rmii_rxc = priv->rmii_rxc ?0 :MTK_PERICFG_BIT_NIC_CFG_CON_CLK ;break ;default :dev_err (dev,"This interface not supported\n" );return -EINVAL ; } + ret =regmap_update_bits (priv->pericfg, +MTK_PERICFG_REG_NIC_CFG1_CON , +MTK_PERICFG_BIT_NIC_CFG_CON_CLK , + rmii_rxc); +if (ret) +return ret; + return regmap_update_bits(priv->pericfg, MTK_PERICFG_REG_NIC_CFG0_CON, MTK_PERICFG_REG_NIC_CFG_CON_CFG_INTF,
@@ -1597,6 +1610,7 @@ static int mt8365_set_interface_mode(struct net_device *ndev)switch (priv->phy_intf) {case PHY_INTERFACE_MODE_RMII : intf_val =MTK_PERICFG_BIT_NIC_CFG_CON_RMII ; + intf_val |= priv->rmii_rxc ?0 :MTK_PERICFG_BIT_NIC_CFG_CON_CLK_V2 ;break ;default :dev_err (dev,"This interface not supported\n" );
@@ -1605,7 +1619,8 @@ static int mt8365_set_interface_mode(struct net_device *ndev)return regmap_update_bits (priv->pericfg,MTK_PERICFG_REG_NIC_CFG_CON_V2 , -MTK_PERICFG_REG_NIC_CFG_CON_CFG_INTF , +MTK_PERICFG_REG_NIC_CFG_CON_CFG_INTF | +MTK_PERICFG_BIT_NIC_CFG_CON_CLK_V2 , intf_val); }
Signature · 1 line
2.25.1
Re: [PATCH net-next v2 5/9] net: ethernet: mtk-star-emac: add clock pad selection for RMII
Quoted 80 lines · Biao Huang
This patch add a new dts property named "mediatek,rmii-rxc" parsing in driver, which will configure MAC to select which pin the RMII reference clock is connected to, TXC or RXC.
TXC pad is the default reference clock pin. If user wants to use RXC pad instead, add "mediatek,rmii-rxc" to corresponding device node.
Signed-off-by Biao Huang <[email protected]>Signed-off-by Yinghua Pan <[email protected]>--- drivers/net/ethernet/mediatek/mtk_star_emac.c | 19 +++++++++++++++++-- 1 file changed, 17 insertions(+), 2 deletions(-)drivers/net/ethernet/mediatek/mtk_star_emac.c +15
-1@@ -189,6 +189,8 @@ static const char *const mtk_star_clk_names[] = { "core", "reg", "trans" };#define MTK_PERICFG_REG_NIC_CFG_CON_V2 0x0c10#define MTK_PERICFG_REG_NIC_CFG_CON_CFG_INTF GENMASK(3, 0)#define MTK_PERICFG_BIT_NIC_CFG_CON_RMII 1 +#define MTK_PERICFG_BIT_NIC_CFG_CON_CLK BIT(0) +#define MTK_PERICFG_BIT_NIC_CFG_CON_CLK_V2 BIT(8)/* Represents the actual structure of descriptors used by the MAC. We can * reuse the same structure for both TX and RX - the layout is the same, only @@ -265,6 +267,7 @@ struct mtk_star_priv {int speed;int duplex;int pause; +bool rmii_rxc;const struct mtk_star_compat *compat_data;@@ -1528,6 +1531,8 @@ static int mtk_star_probe(struct platform_device *pdev)return -ENODEV ; } + priv->rmii_rxc =of_property_read_bool (of_node,"mediatek,rmii-rxc" ); +if (priv->compat_data->set_interface_mode) { ret = priv->compat_data->set_interface_mode (ndev);if (ret) {@@ -1571,17 +1576,25 @@ static int mt8516_set_interface_mode(struct net_device *ndev) {struct mtk_star_priv *priv =netdev_priv (ndev);struct device *dev =mtk_star_get_dev (priv); -unsigned int intf_val; +unsigned int intf_val, ret, rmii_rxc;switch (priv->phy_intf) {case PHY_INTERFACE_MODE_RMII : intf_val =MTK_PERICFG_BIT_NIC_CFG_CON_RMII ; + rmii_rxc = priv->rmii_rxc ?0 :MTK_PERICFG_BIT_NIC_CFG_CON_CLK ;break ;default :dev_err (dev,"This interface not supported\n" );return -EINVAL ; } + ret =regmap_update_bits (priv->pericfg, +MTK_PERICFG_REG_NIC_CFG1_CON , +MTK_PERICFG_BIT_NIC_CFG_CON_CLK , + rmii_rxc); +if (ret) +return ret; + return regmap_update_bits(priv->pericfg, MTK_PERICFG_REG_NIC_CFG0_CON, MTK_PERICFG_REG_NIC_CFG_CON_CFG_INTF,@@ -1597,6 +1610,7 @@ static int mt8365_set_interface_mode(struct net_device *ndev)switch (priv->phy_intf) {case PHY_INTERFACE_MODE_RMII : intf_val =MTK_PERICFG_BIT_NIC_CFG_CON_RMII ; + intf_val |= priv->rmii_rxc ?0 :MTK_PERICFG_BIT_NIC_CFG_CON_CLK_V2 ;break ;default :dev_err (dev,"This interface not supported\n" );
drivers/net/ethernet/mediatek/mtk_star_emac.c static int mt8365_set_interface_mode(struct net_device *ndev) · line 1626
Quoted 9 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +2
-1@@ -1605,7 +1619,8 @@ static int mt8365_set_interface_mode(struct net_device *ndev)return regmap_update_bits (priv->pericfg,MTK_PERICFG_REG_NIC_CFG_CON_V2 , -MTK_PERICFG_REG_NIC_CFG_CON_CFG_INTF , +MTK_PERICFG_REG_NIC_CFG_CON_CFG_INTF | +MTK_PERICFG_BIT_NIC_CFG_CON_CLK_V2 , intf_val); }
Regards,
Macpaul Lin
PATCH v2 6/9 net: ethernet: mtk-star-emac: add timing adjustment support
In reply to Biao HuangAdd simple clock inversion for timing adjustment in driver. Add property "mediatek,txc-inverse" or "mediatek,rxc-inverse" to device node when necessary.
--- drivers/net/ethernet/mediatek/mtk_star_emac.c | 34 +++++++++++++++++++ 1 file changed, 34 insertions(+)
drivers/net/ethernet/mediatek/mtk_star_emac.c +34 -0
@@ -131,6 +131,11 @@ static const char *const mtk_star_clk_names[] = { "core", "reg", "trans" };#define MTK_STAR_REG_INT_MASK 0x0054#define MTK_STAR_BIT_INT_MASK_FNRC BIT(6) +/* Delay-Macro Register */ +#define MTK_STAR_REG_TEST0 0x0058 +#define MTK_STAR_BIT_INV_RX_CLK BIT(30) +#define MTK_STAR_BIT_INV_TX_CLK BIT(31) +/* Misc. Config Register */ #define MTK_STAR_REG_TEST1 0x005c#define MTK_STAR_BIT_TEST1_RST_HASH_MBIST BIT(31)
@@ -268,6 +273,8 @@ struct mtk_star_priv {int duplex;int pause;bool rmii_rxc; +bool rx_inv; +bool tx_inv;const struct mtk_star_compat *compat_data;
@@ -1450,6 +1457,25 @@ static void mtk_star_clk_disable_unprepare(void *data)clk_bulk_disable_unprepare (MTK_STAR_NCLKS , priv->clks); } +static int mtk_star_set_timing (struct mtk_star_priv *priv) +{ +struct device *dev =mtk_star_get_dev (priv); +unsigned int delay_val =0 ; + +switch (priv->phy_intf) { +case PHY_INTERFACE_MODE_RMII : + delay_val |=FIELD_PREP (MTK_STAR_BIT_INV_RX_CLK , priv->rx_inv); + delay_val |=FIELD_PREP (MTK_STAR_BIT_INV_TX_CLK , priv->tx_inv); +break ; +default : +dev_err (dev,"This interface not supported\n" ); +return -EINVAL ; + } + +regmap_write (priv->regs,MTK_STAR_REG_TEST0 , delay_val); + +return 0 ; +}static int mtk_star_probe (struct platform_device *pdev) {struct device_node *of_node;
@@ -1532,6 +1558,8 @@ static int mtk_star_probe(struct platform_device *pdev) } priv->rmii_rxc =of_property_read_bool (of_node,"mediatek,rmii-rxc" ); + priv->rx_inv =of_property_read_bool (of_node,"mediatek,rxc-inverse" ); + priv->tx_inv =of_property_read_bool (of_node,"mediatek,txc-inverse" );if (priv->compat_data->set_interface_mode) { ret = priv->compat_data->set_interface_mode (ndev);
@@ -1541,6 +1569,12 @@ static int mtk_star_probe(struct platform_device *pdev) } } + ret =mtk_star_set_timing (priv); +if (ret) { +dev_err (dev,"Failed to set timing, err = %d\n" , ret); +return -EINVAL ; + } + ret =dma_set_mask_and_coherent (dev,DMA_BIT_MASK (32 ));if (ret) {dev_err (dev,"unsupported DMA mask\n" );
Signature · 1 line
2.25.1
Re: [PATCH net-next v2 6/9] net: ethernet: mtk-star-emac: add timing adjustment support
Quoted 74 lines · Biao Huang
Add simple clock inversion for timing adjustment in driver. Add property "mediatek,txc-inverse" or "mediatek,rxc-inverse" to device node when necessary.
Signed-off-by Biao Huang <[email protected]>Signed-off-by Yinghua Pan <[email protected]>--- drivers/net/ethernet/mediatek/mtk_star_emac.c | 34 +++++++++++++++++++ 1 file changed, 34 insertions(+)drivers/net/ethernet/mediatek/mtk_star_emac.c +28
-0@@ -131,6 +131,11 @@ static const char *const mtk_star_clk_names[] = { "core", "reg", "trans" };#define MTK_STAR_REG_INT_MASK 0x0054#define MTK_STAR_BIT_INT_MASK_FNRC BIT(6) +/* Delay-Macro Register */ +#define MTK_STAR_REG_TEST0 0x0058 +#define MTK_STAR_BIT_INV_RX_CLK BIT(30) +#define MTK_STAR_BIT_INV_TX_CLK BIT(31) +/* Misc. Config Register */ #define MTK_STAR_REG_TEST1 0x005c#define MTK_STAR_BIT_TEST1_RST_HASH_MBIST BIT(31)@@ -268,6 +273,8 @@ struct mtk_star_priv {int duplex;int pause;bool rmii_rxc; +bool rx_inv; +bool tx_inv;const struct mtk_star_compat *compat_data;@@ -1450,6 +1457,25 @@ static void mtk_star_clk_disable_unprepare(void *data)clk_bulk_disable_unprepare (MTK_STAR_NCLKS , priv->clks); } +static int mtk_star_set_timing (struct mtk_star_priv *priv) +{ +struct device *dev =mtk_star_get_dev (priv); +unsigned int delay_val =0 ; + +switch (priv->phy_intf) { +case PHY_INTERFACE_MODE_RMII : + delay_val |=FIELD_PREP (MTK_STAR_BIT_INV_RX_CLK , priv->rx_inv); + delay_val |=FIELD_PREP (MTK_STAR_BIT_INV_TX_CLK , priv->tx_inv); +break ; +default : +dev_err (dev,"This interface not supported\n" ); +return -EINVAL ; + } + +regmap_write (priv->regs,MTK_STAR_REG_TEST0 , delay_val); + +return 0 ; +}static int mtk_star_probe (struct platform_device *pdev) {struct device_node *of_node;@@ -1532,6 +1558,8 @@ static int mtk_star_probe(struct platform_device *pdev) } priv->rmii_rxc =of_property_read_bool (of_node,"mediatek,rmii-rxc" ); + priv->rx_inv =of_property_read_bool (of_node,"mediatek,rxc-inverse" ); + priv->tx_inv =of_property_read_bool (of_node,"mediatek,txc-inverse" );if (priv->compat_data->set_interface_mode) { ret = priv->compat_data->set_interface_mode (ndev);@@ -1541,6 +1569,12 @@ static int mtk_star_probe(struct platform_device *pdev) } }
drivers/net/ethernet/mediatek/mtk_star_emac.c static int mtk_star_probe(struct platform_device *pdev) · line 1580
Quoted 10 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +6
-0+ ret =mtk_star_set_timing (priv); +if (ret) { +dev_err (dev,"Failed to set timing, err = %d\n" , ret); +return -EINVAL ; + } + ret =dma_set_mask_and_coherent (dev,DMA_BIT_MASK (32 ));if (ret) {dev_err (dev,"unsupported DMA mask\n" );
Regards,
Macpaul Lin
PATCH v2 7/9 dt-bindings: net: mtk-star-emac: add description for new properties
In reply to Biao HuangAdd description for new properties which will be parsed in driver.
--- .../bindings/net/mediatek,star-emac.yaml | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)
Documentation/devicetree/bindings/net/mediatek,star-emac.yaml +16 -0
@@ -48,6 +48,22 @@ properties: Phandle to the device containing the PERICFG register range. This is used to control the MII mode. + mediatek,rmii-rxc: + type: boolean + description: + If present, indicates that the RMII reference clock, which is from external + PHYs, is connected to RXC pin. Otherwise, is connected to TXC pin. + + mediatek,rxc-inverse: + type: boolean + description: + If present, indicates that clock on RXC pad will be inversed. + + mediatek,txc-inverse: + type: boolean + description: + If present, indicates that clock on TXC pad will be inversed. + mdio: type: object description:
Signature · 1 line
2.25.1
Re: [PATCH net-next v2 7/9] dt-bindings: net: mtk-star-emac: add description for new properties
Quoted 7 lines · Biao Huang
Add description for new properties which will be parsed in driver.
Signed-off-by Biao Huang <[email protected]>--- .../bindings/net/mediatek,star-emac.yaml | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)
_______________________________________________
Linux-mediatek mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-mediatek
PATCH v2 8/9 net: ethernet: mtk-star-emac: add support for MII interface
In reply to Biao HuangAdd support for MII interface.
If user wants to use MII, assign "MII" to "phy-mode" property in dts.
--- drivers/net/ethernet/mediatek/mtk_star_emac.c | 13 +++++++++++-- 1 file changed, 11 insertions(+), 2 deletions(-)
drivers/net/ethernet/mediatek/mtk_star_emac.c +11 -2
@@ -193,6 +193,7 @@ static const char *const mtk_star_clk_names[] = { "core", "reg", "trans" };#define MTK_PERICFG_REG_NIC_CFG1_CON 0x03c8#define MTK_PERICFG_REG_NIC_CFG_CON_V2 0x0c10#define MTK_PERICFG_REG_NIC_CFG_CON_CFG_INTF GENMASK(3, 0) +#define MTK_PERICFG_BIT_NIC_CFG_CON_MII 0#define MTK_PERICFG_BIT_NIC_CFG_CON_RMII 1#define MTK_PERICFG_BIT_NIC_CFG_CON_CLK BIT(0)#define MTK_PERICFG_BIT_NIC_CFG_CON_CLK_V2 BIT(8)
@@ -1463,6 +1464,7 @@ static int mtk_star_set_timing(struct mtk_star_priv *priv)unsigned int delay_val =0 ;switch (priv->phy_intf) { +case PHY_INTERFACE_MODE_MII :case PHY_INTERFACE_MODE_RMII : delay_val |=FIELD_PREP (MTK_STAR_BIT_INV_RX_CLK , priv->rx_inv); delay_val |=FIELD_PREP (MTK_STAR_BIT_INV_TX_CLK , priv->tx_inv);
@@ -1545,7 +1547,8 @@ static int mtk_star_probe(struct platform_device *pdev) ret =of_get_phy_mode (of_node, &priv->phy_intf);if (ret) {return ret; - }else if (priv->phy_intf !=PHY_INTERFACE_MODE_RMII ) { + }else if (priv->phy_intf !=PHY_INTERFACE_MODE_RMII && + priv->phy_intf !=PHY_INTERFACE_MODE_MII ) {dev_err (dev,"unsupported phy mode: %s\n" ,phy_modes (priv->phy_intf));return -EINVAL ;
@@ -1610,9 +1613,12 @@ static int mt8516_set_interface_mode(struct net_device *ndev) {struct mtk_star_priv *priv =netdev_priv (ndev);struct device *dev =mtk_star_get_dev (priv); -unsigned int intf_val, ret, rmii_rxc; +unsigned int intf_val, ret, rmii_rxc =0 ;switch (priv->phy_intf) { +case PHY_INTERFACE_MODE_MII : + intf_val =MTK_PERICFG_BIT_NIC_CFG_CON_MII ; +break ;case PHY_INTERFACE_MODE_RMII : intf_val =MTK_PERICFG_BIT_NIC_CFG_CON_RMII ; rmii_rxc = priv->rmii_rxc ?0 :MTK_PERICFG_BIT_NIC_CFG_CON_CLK ;
@@ -1642,6 +1648,9 @@ static int mt8365_set_interface_mode(struct net_device *ndev)unsigned int intf_val;switch (priv->phy_intf) { +case PHY_INTERFACE_MODE_MII : + intf_val =MTK_PERICFG_BIT_NIC_CFG_CON_MII ; +break ;case PHY_INTERFACE_MODE_RMII : intf_val =MTK_PERICFG_BIT_NIC_CFG_CON_RMII ; intf_val |= priv->rmii_rxc ?0 :MTK_PERICFG_BIT_NIC_CFG_CON_CLK_V2 ;
Signature · 1 line
2.25.1
Re: [PATCH net-next v2 8/9] net: ethernet: mtk-star-emac: add support for MII interface
Quoted 55 lines · Biao Huang
Add support for MII interface.
If user wants to use MII, assign "MII" to "phy-mode" property in dts.Signed-off-by Biao Huang <[email protected]>Signed-off-by Yinghua Pan <[email protected]>--- drivers/net/ethernet/mediatek/mtk_star_emac.c | 13 +++++++++++-- 1 file changed, 11 insertions(+), 2 deletions(-)drivers/net/ethernet/mediatek/mtk_star_emac.c +8
-2@@ -193,6 +193,7 @@ static const char *const mtk_star_clk_names[] = { "core", "reg", "trans" };#define MTK_PERICFG_REG_NIC_CFG1_CON 0x03c8#define MTK_PERICFG_REG_NIC_CFG_CON_V2 0x0c10#define MTK_PERICFG_REG_NIC_CFG_CON_CFG_INTF GENMASK(3, 0) +#define MTK_PERICFG_BIT_NIC_CFG_CON_MII 0#define MTK_PERICFG_BIT_NIC_CFG_CON_RMII 1#define MTK_PERICFG_BIT_NIC_CFG_CON_CLK BIT(0)#define MTK_PERICFG_BIT_NIC_CFG_CON_CLK_V2 BIT(8)@@ -1463,6 +1464,7 @@ static int mtk_star_set_timing(struct mtk_star_priv *priv)unsigned int delay_val =0 ;switch (priv->phy_intf) { +case PHY_INTERFACE_MODE_MII :case PHY_INTERFACE_MODE_RMII : delay_val |=FIELD_PREP (MTK_STAR_BIT_INV_RX_CLK , priv->rx_inv); delay_val |=FIELD_PREP (MTK_STAR_BIT_INV_TX_CLK , priv->tx_inv);@@ -1545,7 +1547,8 @@ static int mtk_star_probe(struct platform_device *pdev) ret =of_get_phy_mode (of_node, &priv->phy_intf);if (ret) {return ret; - }else if (priv->phy_intf !=PHY_INTERFACE_MODE_RMII ) { + }else if (priv->phy_intf !=PHY_INTERFACE_MODE_RMII && + priv->phy_intf !=PHY_INTERFACE_MODE_MII ) {dev_err (dev,"unsupported phy mode: %s\n" ,phy_modes (priv->phy_intf));return -EINVAL ;@@ -1610,9 +1613,12 @@ static int mt8516_set_interface_mode(struct net_device *ndev) {struct mtk_star_priv *priv =netdev_priv (ndev);struct device *dev =mtk_star_get_dev (priv); -unsigned int intf_val, ret, rmii_rxc; +unsigned int intf_val, ret, rmii_rxc =0 ;switch (priv->phy_intf) { +case PHY_INTERFACE_MODE_MII : + intf_val =MTK_PERICFG_BIT_NIC_CFG_CON_MII ; +break ;case PHY_INTERFACE_MODE_RMII : intf_val =MTK_PERICFG_BIT_NIC_CFG_CON_RMII ; rmii_rxc = priv->rmii_rxc ?0 :MTK_PERICFG_BIT_NIC_CFG_CON_CLK ;
drivers/net/ethernet/mediatek/mtk_star_emac.c static int mt8365_set_interface_mode(struct net_device *ndev) · line 1656
Quoted 9 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +3
-0@@ -1642,6 +1648,9 @@ static int mt8365_set_interface_mode(struct net_device *ndev)unsigned int intf_val;switch (priv->phy_intf) { +case PHY_INTERFACE_MODE_MII : + intf_val =MTK_PERICFG_BIT_NIC_CFG_CON_MII ; +break ;case PHY_INTERFACE_MODE_RMII : intf_val =MTK_PERICFG_BIT_NIC_CFG_CON_RMII ; intf_val |= priv->rmii_rxc ?0 :MTK_PERICFG_BIT_NIC_CFG_CON_CLK_V2 ;
Regards,
Macpaul Lin
PATCH v2 9/9 net: ethernet: mtk-star-emac: separate tx/rx handling with two NAPIs
In reply to Biao HuangCurrent driver may lost tx interrupts under bidirectional test with iperf3, which leads to some unexpected issues.
This patch let rx/tx interrupt enable/disable separately, and rx/tx are handled in different NAPIs.
--- drivers/net/ethernet/mediatek/mtk_star_emac.c | 317 ++++++++++-------- 1 file changed, 181 insertions(+), 136 deletions(-)
drivers/net/ethernet/mediatek/mtk_star_emac.c +181 -136
@@ -229,7 +229,7 @@ struct mtk_star_ring_desc_data {struct sk_buff *skb; }; -#define MTK_STAR_RING_NUM_DESCS 128 +#define MTK_STAR_RING_NUM_DESCS 512#define MTK_STAR_NUM_TX_DESCS MTK_STAR_RING_NUM_DESCS#define MTK_STAR_NUM_RX_DESCS MTK_STAR_RING_NUM_DESCS#define MTK_STAR_NUM_DESCS_TOTAL (MTK_STAR_RING_NUM_DESCS * 2)
@@ -264,7 +264,8 @@ struct mtk_star_priv {struct mtk_star_ring rx_ring;struct mii_bus *mii; -struct napi_struct napi; +struct napi_struct tx_napi; +struct napi_struct rx_napi;struct device_node *phy_node;phy_interface_t phy_intf;
@@ -380,19 +381,16 @@ mtk_star_ring_push_head_tx(struct mtk_star_ring *ring,mtk_star_ring_push_head (ring, desc_data, flags); } -static unsigned int mtk_star_ring_num_used_descs (struct mtk_star_ring *ring) +static unsigned int mtk_star_tx_ring_avail (struct mtk_star_ring *ring) { -return abs (ring->head - ring->tail); -} +u32 avail; -static bool mtk_star_ring_full (struct mtk_star_ring *ring) -{ -return mtk_star_ring_num_used_descs (ring) ==MTK_STAR_RING_NUM_DESCS ; -} +if (ring->tail > ring->head) + avail = ring->tail - ring->head -1 ; +else + avail =MTK_STAR_RING_NUM_DESCS - ring->head + ring->tail -1 ; -static bool mtk_star_ring_descs_available (struct mtk_star_ring *ring) -{ -return mtk_star_ring_num_used_descs (ring) >0 ; +return avail; } static dma_addr_t mtk_star_dma_map_rx(struct mtk_star_priv *priv,
@@ -415,7 +413,7 @@ static void mtk_star_dma_unmap_rx(struct mtk_star_priv *priv, }static dma_addr_t mtk_star_dma_map_tx (struct mtk_star_priv *priv, -struct sk_buff *skb) +struct sk_buff *skb) {struct device *dev =mtk_star_get_dev (priv);
@@ -437,6 +435,36 @@ static void mtk_star_nic_disable_pd(struct mtk_star_priv *priv) MTK_STAR_BIT_MAC_CFG_NIC_PD); } +static void mtk_star_enable_dma_irq (struct mtk_star_priv *priv, +bool rx,bool tx) +{ +u32 value; + +regmap_read (priv->regs,MTK_STAR_REG_INT_MASK , &value); + +if (tx) + value &= ~MTK_STAR_BIT_INT_STS_TNTC ; +if (rx) + value &= ~MTK_STAR_BIT_INT_STS_FNRC ; + +regmap_write (priv->regs,MTK_STAR_REG_INT_MASK , value); +} + +static void mtk_star_disable_dma_irq (struct mtk_star_priv *priv, +bool rx,bool tx) +{ +u32 value; + +regmap_read (priv->regs,MTK_STAR_REG_INT_MASK , &value); + +if (tx) + value |=MTK_STAR_BIT_INT_STS_TNTC ; +if (rx) + value |=MTK_STAR_BIT_INT_STS_FNRC ; + +regmap_write (priv->regs,MTK_STAR_REG_INT_MASK , value); +} +/* Unmask the three interrupts we care about, mask all others. */ static void mtk_star_intr_enable (struct mtk_star_priv *priv) {
@@ -452,20 +480,11 @@ static void mtk_star_intr_disable(struct mtk_star_priv *priv)regmap_write (priv->regs,MTK_STAR_REG_INT_MASK , ~0 ); } -static unsigned int mtk_star_intr_read (struct mtk_star_priv *priv) -{ -unsigned int val; - -regmap_read (priv->regs,MTK_STAR_REG_INT_STS , &val); - -return val; -} -static unsigned int mtk_star_intr_ack_all (struct mtk_star_priv *priv) {unsigned int val; - val =mtk_star_intr_read (priv); +regmap_read (priv->regs,MTK_STAR_REG_INT_STS , &val);regmap_write (priv->regs,MTK_STAR_REG_INT_STS , val);return val;
@@ -737,25 +756,46 @@ static void mtk_star_free_tx_skbs(struct mtk_star_priv *priv)mtk_star_ring_free_skbs (priv, ring, mtk_star_dma_unmap_tx); } -/* All processing for TX and RX happens in the napi poll callback. -* -* FIXME: The interrupt handling should be more fine-grained with each -* interrupt enabled/disabled independently when needed. Unfortunatly this -* turned out to impact the driver's stability and until we have something -* working properly, we're disabling all interrupts during TX & RX processing -* or when resetting the counter registers. +/* mtk_star_handle_irq - Interrupt Handler. +* @irq: interrupt number. +* @data: pointer to a network interface device structure. +* Description : this is the driver interrupt service routine. +* it mainly handles: +* 1. tx complete interrupt for frame transmission. +* 2. rx complete interrupt for frame reception. +* 3. MAC Management Counter interrupt to avoid counter overflow. */ static irqreturn_t mtk_star_handle_irq (int irq,void *data) { -struct mtk_star_priv *priv; -struct net_device *ndev; +struct net_device *ndev = data; +struct mtk_star_priv *priv =netdev_priv (ndev); +unsigned int intr_status =mtk_star_intr_ack_all (priv); +unsigned long flags =0 ; + +if (intr_status &MTK_STAR_BIT_INT_STS_FNRC ) { +if (napi_schedule_prep (&priv->rx_napi)) { +spin_lock_irqsave (&priv->lock, flags); +/* mask Rx Complete interrupt */ +mtk_star_disable_dma_irq (priv, true, false); +spin_unlock_irqrestore (&priv->lock, flags); +__napi_schedule_irqoff (&priv->rx_napi); + } + } - ndev = data; - priv =netdev_priv (ndev); +if (intr_status &MTK_STAR_BIT_INT_STS_TNTC ) { +if (napi_schedule_prep (&priv->tx_napi)) { +spin_lock_irqsave (&priv->lock, flags); +/* mask Tx Complete interrupt */ +mtk_star_disable_dma_irq (priv, false, true); +spin_unlock_irqrestore (&priv->lock, flags); +__napi_schedule_irqoff (&priv->tx_napi); + } + } -if (netif_running (ndev)) { -mtk_star_intr_disable (priv); -napi_schedule (&priv->napi); +/* interrupt is triggered once any counters reach 0x8000000 */ +if (intr_status &MTK_STAR_REG_INT_STS_MIB_CNT_TH ) { +mtk_star_update_stats (priv); +mtk_star_reset_counters (priv); }return IRQ_HANDLED ;
@@ -971,7 +1011,8 @@ static int mtk_star_enable(struct net_device *ndev)if (ret) goto err_free_skbs; -napi_enable (&priv->napi); +napi_enable (&priv->tx_napi); +napi_enable (&priv->rx_napi);mtk_star_intr_ack_all (priv);mtk_star_intr_enable (priv);
@@ -1004,7 +1045,8 @@ static void mtk_star_disable(struct net_device *ndev)struct mtk_star_priv *priv =netdev_priv (ndev);netif_stop_queue (ndev); -napi_disable (&priv->napi); +napi_disable (&priv->tx_napi); +napi_disable (&priv->rx_napi);mtk_star_intr_disable (priv);mtk_star_dma_disable (priv);mtk_star_intr_ack_all (priv);
@@ -1043,6 +1085,17 @@ static int mtk_star_netdev_start_xmit(struct sk_buff *skb,struct mtk_star_ring *ring = &priv->tx_ring;struct device *dev =mtk_star_get_dev (priv);struct mtk_star_ring_desc_data desc_data; +int nfrags =skb_shinfo (skb)->nr_frags; + +if (unlikely (mtk_star_tx_ring_avail (ring) < nfrags +1 )) { +if (!netif_queue_stopped (ndev)) { +netif_stop_queue (ndev); +/* This is a hard error, log it. */ +netdev_err (priv->ndev,"%s: Tx Ring full when queue awake\n" , + __func__); + } +return NETDEV_TX_BUSY ; + } desc_data.dma_addr =mtk_star_dma_map_tx (priv, skb);if (dma_mapping_error (dev, desc_data.dma_addr))
@@ -1050,18 +1103,10 @@ static int mtk_star_netdev_start_xmit(struct sk_buff *skb, desc_data.skb = skb; desc_data.len = skb->len; - -spin_lock_bh (&priv->lock); -mtk_star_ring_push_head_tx (ring, &desc_data);netdev_sent_queue (ndev, skb->len); -if (mtk_star_ring_full (ring)) -netif_stop_queue (ndev); - -spin_unlock_bh (&priv->lock); -mtk_star_dma_resume_tx (priv);return NETDEV_TX_OK ;
@@ -1092,23 +1137,31 @@ static int mtk_star_tx_complete_one(struct mtk_star_priv *priv)return ret; } -static void mtk_star_tx_complete_all (struct mtk_star_priv *priv) +static int mtk_star_tx_poll (struct napi_struct *napi,int budget) { -struct mtk_star_ring *ring = &priv->tx_ring; -struct net_device *ndev = priv->ndev; -int ret, pkts_compl, bytes_compl; +int ret, pkts_compl =0 , bytes_compl =0 , count =0 ; +struct mtk_star_priv *priv; +struct mtk_star_ring *ring; +struct net_device *ndev; +unsigned long flags =0 ; +unsigned int entry;bool wake = false; -spin_lock (&priv->lock); + priv = container_of(napi, struct mtk_star_priv, tx_napi); + ndev = priv->ndev; -for (pkts_compl =0 , bytes_compl =0 ;; +__netif_tx_lock_bh (netdev_get_tx_queue (priv->ndev,0 )); + ring = &priv->tx_ring; + entry = ring->tail; +for (pkts_compl =0 , bytes_compl =0 ; + (entry != ring->head) && (count < budget); pkts_compl++, bytes_compl += ret, wake = true) { -if (!mtk_star_ring_descs_available (ring)) -break ; ret =mtk_star_tx_complete_one (priv);if (ret <0 )break ; + count++; + entry = ring->tail; }netdev_completed_queue (ndev, pkts_compl, bytes_compl);
@@ -1116,7 +1169,16 @@ static void mtk_star_tx_complete_all(struct mtk_star_priv *priv)if (wake &&netif_queue_stopped (ndev))netif_wake_queue (ndev); -spin_unlock (&priv->lock); +__netif_tx_unlock_bh (netdev_get_tx_queue (priv->ndev,0 )); + + count =min (count, budget); +if (count < budget &&napi_complete_done (napi, count)) { +spin_lock_irqsave (&priv->lock, flags); +mtk_star_enable_dma_irq (priv, false, true); +spin_unlock_irqrestore (&priv->lock, flags); + } + +return count; } static void mtk_star_netdev_get_stats64(struct net_device *ndev,
@@ -1196,7 +1258,7 @@ static const struct ethtool_ops mtk_star_ethtool_ops = { .set_link_ksettings = phy_ethtool_set_link_ksettings, }; -static int mtk_star_receive_packet (struct mtk_star_priv *priv) +static int mtk_star_rx (struct mtk_star_priv *priv,int budget) {struct mtk_star_ring *ring = &priv->rx_ring;struct device *dev =mtk_star_get_dev (priv);
@@ -1204,107 +1266,86 @@ static int mtk_star_receive_packet(struct mtk_star_priv *priv)struct net_device *ndev = priv->ndev;struct sk_buff *curr_skb, *new_skb;dma_addr_t new_dma_addr; -int ret; +int ret, count =0 ; -spin_lock (&priv->lock); - ret =mtk_star_ring_pop_tail (ring, &desc_data); -spin_unlock (&priv->lock); -if (ret) -return -1 ; +while (count < budget) { + ret =mtk_star_ring_pop_tail (ring, &desc_data); +if (ret) +return -1 ; - curr_skb = desc_data.skb; + curr_skb = desc_data.skb; -if ((desc_data.flags &MTK_STAR_DESC_BIT_RX_CRCE ) || - (desc_data.flags &MTK_STAR_DESC_BIT_RX_OSIZE )) { -/* Error packet -> drop and reuse skb. */ - new_skb = curr_skb; - goto push_new_skb; - } +if ((desc_data.flags &MTK_STAR_DESC_BIT_RX_CRCE ) || + (desc_data.flags &MTK_STAR_DESC_BIT_RX_OSIZE )) { +/* Error packet -> drop and reuse skb. */ + new_skb = curr_skb; + goto push_new_skb; + } -/* Prepare new skb before receiving the current one. Reuse the current -* skb if we fail at any point. -*/ - new_skb =mtk_star_alloc_skb (ndev); -if (!new_skb) { - ndev->stats.rx_dropped++; - new_skb = curr_skb; - goto push_new_skb; - } +/* Prepare new skb before receiving the current one. +* Reuse the current skb if we fail at any point. +*/ + new_skb =mtk_star_alloc_skb (ndev); +if (!new_skb) { + ndev->stats.rx_dropped++; + new_skb = curr_skb; + goto push_new_skb; + } - new_dma_addr =mtk_star_dma_map_rx (priv, new_skb); -if (dma_mapping_error (dev, new_dma_addr)) { - ndev->stats.rx_dropped++; -dev_kfree_skb (new_skb); - new_skb = curr_skb; -netdev_err (ndev,"DMA mapping error of RX descriptor\n" ); - goto push_new_skb; - } + new_dma_addr =mtk_star_dma_map_rx (priv, new_skb); +if (dma_mapping_error (dev, new_dma_addr)) { + ndev->stats.rx_dropped++; +dev_kfree_skb (new_skb); + new_skb = curr_skb; +netdev_err (ndev,"DMA mapping error of RX descriptor\n" ); + goto push_new_skb; + } -/* We can't fail anymore at this point: it's safe to unmap the skb. */ -mtk_star_dma_unmap_rx (priv, &desc_data); +/* We can't fail anymore at this point: +* it's safe to unmap the skb. +*/ +mtk_star_dma_unmap_rx (priv, &desc_data); -skb_put (desc_data.skb, desc_data.len); - desc_data.skb->ip_summed =CHECKSUM_NONE ; - desc_data.skb->protocol =eth_type_trans (desc_data.skb, ndev); - desc_data.skb->dev = ndev; -netif_receive_skb (desc_data.skb); +skb_put (desc_data.skb, desc_data.len); + desc_data.skb->ip_summed =CHECKSUM_NONE ; + desc_data.skb->protocol =eth_type_trans (desc_data.skb, ndev); + desc_data.skb->dev = ndev; +netif_receive_skb (desc_data.skb); -/* update dma_addr for new skb */ - desc_data.dma_addr = new_dma_addr; +/* update dma_addr for new skb */ + desc_data.dma_addr = new_dma_addr; push_new_skb: - desc_data.len =skb_tailroom (new_skb); - desc_data.skb = new_skb; - -spin_lock (&priv->lock); -mtk_star_ring_push_head_rx (ring, &desc_data); -spin_unlock (&priv->lock); - -return 0 ; -} -static int mtk_star_process_rx (struct mtk_star_priv *priv,int budget) -{ -int received, ret; + count++; -for (received =0 , ret =0 ; received < budget && ret ==0 ; received++) - ret =mtk_star_receive_packet (priv); + desc_data.len =skb_tailroom (new_skb); + desc_data.skb = new_skb; +mtk_star_ring_push_head_rx (ring, &desc_data); + }mtk_star_dma_resume_rx (priv); -return received; +return count; } -static int mtk_star_poll (struct napi_struct *napi,int budget) +static int mtk_star_rx_poll (struct napi_struct *napi,int budget) {struct mtk_star_priv *priv; -unsigned int status; -int received =0 ; +unsigned long flags =0 ; +int work_done =0 ; - priv = container_of(napi, struct mtk_star_priv, napi); + priv = container_of(napi, struct mtk_star_priv, rx_napi); - status =mtk_star_intr_read (priv); -mtk_star_intr_ack_all (priv); - -if (status &MTK_STAR_BIT_INT_STS_TNTC ) -/* Clean-up all TX descriptors. */ -mtk_star_tx_complete_all (priv); - -if (status &MTK_STAR_BIT_INT_STS_FNRC ) -/* Receive up to $budget packets. */ - received =mtk_star_process_rx (priv, budget); - -if (unlikely (status &MTK_STAR_REG_INT_STS_MIB_CNT_TH )) { -mtk_star_update_stats (priv); -mtk_star_reset_counters (priv); + work_done =mtk_star_rx (priv, budget); +if (work_done < budget) { +napi_complete_done (napi, work_done); +spin_lock_irqsave (&priv->lock, flags); +mtk_star_enable_dma_irq (priv, true, false); +spin_unlock_irqrestore (&priv->lock, flags); } -if (received < budget) -napi_complete_done (napi, received); - -mtk_star_intr_enable (priv); - -return received; +return work_done; }static void mtk_star_mdio_rwok_clear (struct mtk_star_priv *priv)
@@ -1478,6 +1519,7 @@ static int mtk_star_set_timing(struct mtk_star_priv *priv)return 0 ; } +static int mtk_star_probe (struct platform_device *pdev) {struct device_node *of_node;
@@ -1604,7 +1646,10 @@ static int mtk_star_probe(struct platform_device *pdev) ndev->netdev_ops = &mtk_star_netdev_ops; ndev->ethtool_ops = &mtk_star_ethtool_ops; -netif_napi_add (ndev, &priv->napi, mtk_star_poll,MTK_STAR_NAPI_WEIGHT ); +netif_napi_add (ndev, &priv->rx_napi, + mtk_star_rx_poll,MTK_STAR_NAPI_WEIGHT ); +netif_tx_napi_add (ndev, &priv->tx_napi, + mtk_star_tx_poll,MTK_STAR_NAPI_WEIGHT );return devm_register_netdev (dev, ndev); }
Signature · 1 line
2.25.1
Jakub Kicinski
maintainerRe: [PATCH net-next v2 9/9] net: ethernet: mtk-star-emac: separate tx/rx handling with two NAPIs
Quoted 9 lines · On Thu, 27 Jan 2022 09:58:57 +0800 Biao Huang wrote:
Current driver may lost tx interrupts under bidirectional test with iperf3, which leads to some unexpected issues.
This patch let rx/tx interrupt enable/disable separately, and rx/tx are handled in different NAPIs.
+/*
mtk_star_handle_irq- Interrupt Handler.
+ * @irq: interrupt number.
+ * @data: pointer to a network interface device structure.
if you mean this to me a kdoc comment it needs to start with /**
Quoted 26 lines
+ * Description : this is the driver interrupt service routine.
+ * it mainly handles:+ * 1. tx complete interrupt for frame transmission. + * 2. rx complete interrupt for frame reception. + * 3. MAC Management Counter interrupt to avoid counter overflow.*/
staticirqreturn_tmtk_star_handle_irq(int irq, void *data){drivers/net/ethernet/mediatek/mtk_star_emac.c +14
-3-struct mtk_star_priv *priv; -struct net_device *ndev; +struct net_device *ndev = data; +struct mtk_star_priv *priv =netdev_priv (ndev); +unsigned int intr_status =mtk_star_intr_ack_all (priv); +unsigned long flags =0 ; + +if (intr_status &MTK_STAR_BIT_INT_STS_FNRC ) { +if (napi_schedule_prep (&priv->rx_napi)) { +spin_lock_irqsave (&priv->lock, flags); +/* mask Rx Complete interrupt */ +mtk_star_disable_dma_irq (priv, true, false); +spin_unlock_irqrestore (&priv->lock, flags); +__napi_schedule_irqoff (&priv->rx_napi); + } + } - ndev = data;
drivers/net/ethernet/mediatek/mtk_star_emac.c static void mtk_star_free_tx_skbs(struct mtk_star_priv *priv) · line 793
Quoted 10 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +9
-1- priv =netdev_priv (ndev); +if (intr_status &MTK_STAR_BIT_INT_STS_TNTC ) { +if (napi_schedule_prep (&priv->tx_napi)) { +spin_lock_irqsave (&priv->lock, flags); +/* mask Tx Complete interrupt */ +mtk_star_disable_dma_irq (priv, false, true); +spin_unlock_irqrestore (&priv->lock, flags); +__napi_schedule_irqoff (&priv->tx_napi); + } + }
Seems a little wasteful to retake the same lock twice if two IRQ sources fire at the same time.
drivers/net/ethernet/mediatek/mtk_star_emac.c static int mtk_star_netdev_start_xmit(struct sk_buff *skb, · line 1095
Quoted 12 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +8
-0@@ -1043,6 +1085,17 @@ static int mtk_star_netdev_start_xmit(struct sk_buff *skb,struct mtk_star_ring *ring = &priv->tx_ring;struct device *dev =mtk_star_get_dev (priv);struct mtk_star_ring_desc_data desc_data; +int nfrags =skb_shinfo (skb)->nr_frags; + +if (unlikely (mtk_star_tx_ring_avail (ring) < nfrags +1 )) { +if (!netif_queue_stopped (ndev)) { +netif_stop_queue (ndev); +/* This is a hard error, log it. */ +netdev_err (priv->ndev,"%s: Tx Ring full when queue awake\n" , + __func__);
This needs to be rate limited. Also no point printing the function name, unless the same message appears in multiple places.
Quoted 9 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +3
-0+ } +return NETDEV_TX_BUSY ; + } desc_data.dma_addr =mtk_star_dma_map_tx (priv, skb);if (dma_mapping_error (dev, desc_data.dma_addr))@@ -1050,18 +1103,10 @@ static int mtk_star_netdev_start_xmit(struct sk_buff *skb, desc_data.skb = skb;
drivers/net/ethernet/mediatek/mtk_star_emac.c static int mtk_star_netdev_start_xmit(struct sk_buff *skb, · line 1061
Quoted 10 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +0
-4desc_data.len = skb->len; - -spin_lock_bh (&priv->lock);mtk_star_ring_push_head_tx (ring, &desc_data);netdev_sent_queue (ndev, skb->len); -if (mtk_star_ring_full (ring)) -netif_stop_queue (ndev);
Are you stopping the queue in advance somewhere else now? Did you only test this with BQL enabled? Only place that stops the ring also prints a loud warning now AFAICS..
Quoted 10 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +5
-4-static void mtk_star_tx_complete_all (struct mtk_star_priv *priv) +static int mtk_star_tx_poll (struct napi_struct *napi,int budget) { -struct mtk_star_ring *ring = &priv->tx_ring; -struct net_device *ndev = priv->ndev; -int ret, pkts_compl, bytes_compl; +int ret, pkts_compl =0 , bytes_compl =0 , count =0 ; +struct mtk_star_priv *priv; +struct mtk_star_ring *ring; +struct net_device *ndev;
drivers/net/ethernet/mediatek/mtk_star_emac.c static int mtk_star_tx_complete_one(struct mtk_star_priv *priv) · line 1153
Quoted 10 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +5
-2+unsigned long flags =0 ; +unsigned int entry;bool wake = false; -spin_lock (&priv->lock); + priv = container_of(napi, struct mtk_star_priv, tx_napi); + ndev = priv->ndev; - for (pkts_compl = 0, bytes_compl = 0;; +__netif_tx_lock_bh (netdev_get_tx_queue (priv->ndev,0 ));
Do you really need to lock out the Tx while cleaning?
Drivers usually manage to implement concurrent Tx and cleanup with just a couple of memory barriers.
drivers/net/ethernet/mediatek/mtk_star_emac.c static int mtk_star_tx_complete_one(struct mtk_star_priv *priv) · line 1157
Quoted 4 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +4
-0+ ring = &priv->tx_ring; + entry = ring->tail; + for (pkts_compl = 0, bytes_compl = 0; + (entry != ring->head) && (count < budget);
budget is not really relevant for Tx, you can clean the whole ring. netpoll will pass a budget of 0 to clean up rings.
Quoted 41 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +8
-12pkts_compl++, bytes_compl += ret, wake = true) { -if (!mtk_star_ring_descs_available (ring)) -break ; ret =mtk_star_tx_complete_one (priv);if (ret <0 )break ; + count++; + entry = ring->tail; }@@ -1196,7 +1258,7 @@ static const struct ethtool_ops mtk_star_ethtool_ops = { .set_link_ksettings = phy_ethtool_set_link_ksettings, }; -static int mtk_star_receive_packet (struct mtk_star_priv *priv) +static int mtk_star_rx (struct mtk_star_priv *priv,int budget) {struct mtk_star_ring *ring = &priv->rx_ring;struct device *dev =mtk_star_get_dev (priv);@@ -1204,107 +1266,86 @@ static int mtk_star_receive_packet(struct mtk_star_priv *priv)struct net_device *ndev = priv->ndev;struct sk_buff *curr_skb, *new_skb;dma_addr_t new_dma_addr; -int ret; +int ret, count =0 ; -spin_lock (&priv->lock); - ret =mtk_star_ring_pop_tail (ring, &desc_data); -spin_unlock (&priv->lock); -if (ret) -return -1 ; +while (count < budget) { + ret =mtk_star_ring_pop_tail (ring, &desc_data); +if (ret) +return -1 ; -static int mtk_star_process_rx (struct mtk_star_priv *priv,int budget) -{ -int received, ret;
drivers/net/ethernet/mediatek/mtk_star_emac.c static int mtk_star_receive_packet(struct mtk_star_priv *priv) · line 1283
Quoted 10 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +5
-2+ count++; -for (received =0 , ret =0 ; received < budget && ret ==0 ; received++) - ret =mtk_star_receive_packet (priv); + desc_data.len =skb_tailroom (new_skb); + desc_data.skb = new_skb; +mtk_star_ring_push_head_rx (ring, &desc_data); + }mtk_star_dma_resume_rx (priv);
Again you can get a call with a budget of 0, not sure if it's okay to resume DMA in that case..
Quoted 3 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +1
-1-return received; +return count; }
Re: [PATCH net-next v2 9/9] net: ethernet: mtk-star-emac: separate tx/rx handling with two NAPIs
Dear Jakub,
Thanks for your comments!
Quoted 5 lines · Jakub Kicinski
Quoted 4 lines · On Thu, 27 Jan 2022 09:58:57 +0800 Biao Huang wrote:
Current driver may lost tx interrupts under bidirectional test with iperf3,
which leads to some unexpected issues.
Quoted 8 lines
Quoted 6 lines
This patch let rx/tx interrupt enable/disable separately, and rx/tx are
handled in different NAPIs.
+/*mtk_star_handle_irq- Interrupt Handler.
+ * @irq: interrupt number.
+ * @data: pointer to a network interface device structure.if you mean this to me a kdoc comment it needs to start with /**
Yes, will fix in next send.
Quoted 26 lines
Quoted 26 lines
+ * Description : this is the driver interrupt service routine.
+ * it mainly handles:+ * 1. tx complete interrupt for frame transmission. + * 2. rx complete interrupt for frame reception. + * 3. MAC Management Counter interrupt to avoid counter overflow.*/
staticirqreturn_tmtk_star_handle_irq(int irq, void *data){drivers/net/ethernet/mediatek/mtk_star_emac.c +14
-2-struct mtk_star_priv *priv; -struct net_device *ndev; +struct net_device *ndev = data; +struct mtk_star_priv *priv =netdev_priv (ndev); +unsigned int intr_status =mtk_star_intr_ack_all (priv); +unsigned long flags =0 ; + +if (intr_status &MTK_STAR_BIT_INT_STS_FNRC ) { +if (napi_schedule_prep (&priv->rx_napi)) { +spin_lock_irqsave (&priv->lock, flags); +/* mask Rx Complete interrupt */ +mtk_star_disable_dma_irq (priv, true, false); +spin_unlock_irqrestore (&priv->lock, flags); +__napi_schedule_irqoff (&priv->rx_napi); + } + }
Quoted 14 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c static void mtk_star_free_tx_skbs(struct mtk_star_priv *priv) · line 793
Quoted 11 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +9
-2- ndev = data; - priv =netdev_priv (ndev); +if (intr_status &MTK_STAR_BIT_INT_STS_TNTC ) { +if (napi_schedule_prep (&priv->tx_napi)) { +spin_lock_irqsave (&priv->lock, flags); +/* mask Tx Complete interrupt */ +mtk_star_disable_dma_irq (priv, false, true); +spin_unlock_irqrestore (&priv->lock, flags); +__napi_schedule_irqoff (&priv->tx_napi); + } + }Seems a little wasteful to retake the same lock twice if two IRQ sources fire at the same time.
The TX/RX irq control bits are in the same register, but they are triggered independently.
So it seems necessary to protect the register access with a spin lock.
Quoted 10 lines
Quoted 10 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +4
-0@@ -1043,6 +1085,17 @@ static int mtk_star_netdev_start_xmit(structsk_buff *skb, struct mtk_star_ring *ring = &priv->tx_ring;struct device *dev =mtk_star_get_dev (priv);struct mtk_star_ring_desc_data desc_data; +int nfrags =skb_shinfo (skb)->nr_frags; + +if (unlikely (mtk_star_tx_ring_avail (ring) < nfrags +1 )) { +if (!netif_queue_stopped (ndev)) {
Quoted 8 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c static int mtk_star_netdev_start_xmit(struct sk_buff *skb, · line 1095
Quoted 5 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +4
-0+netif_stop_queue (ndev); +/* This is a hard error, log it. */ + netdev_err(priv->ndev, "%s: Tx Ring full when queue awake\n", + __func__);This needs to be rate limited. Also no point printing the function name, unless the same message appears in multiple places.
OK, will fix in next send.
Quoted 19 lines
Quoted 19 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +3
-0+ } +return NETDEV_TX_BUSY ; + }drivers/net/ethernet/mediatek/mtk_star_emac.c +0
-2desc_data.dma_addr =mtk_star_dma_map_tx (priv, skb);if (dma_mapping_error (dev, desc_data.dma_addr))@@ -1050,18 +1103,10 @@ static int mtk_star_netdev_start_xmit(struct sk_buff *skb, desc_data.skb = skb; desc_data.len = skb->len; - -spin_lock_bh (&priv->lock);mtk_star_ring_push_head_tx (ring, &desc_data);netdev_sent_queue (ndev, skb->len);
Quoted 8 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c static int mtk_star_netdev_start_xmit(struct sk_buff *skb, · line 1061
Quoted 2 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +0
-2-if (mtk_star_ring_full (ring)) -netif_stop_queue (ndev);Are you stopping the queue in advance somewhere else now? Did you only
test this with BQL enabled? Only place that stops the ring also prints
a loud warning now AFAICS..
No.
We modify the ring full condition, and will not invoke netif_stop_queue if queue is already stopped.
Test pass no matter whether BQL is enabled or disabled.
It's much safer to judge queue is full or not at the beginning of start_xmit() to avoid invalid setting.
Quoted 19 lines
Quoted 19 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +9
-5-static void mtk_star_tx_complete_all (struct mtk_star_priv *priv) +static int mtk_star_tx_poll (struct napi_struct *napi,int budget) { -struct mtk_star_ring *ring = &priv->tx_ring; -struct net_device *ndev = priv->ndev; -int ret, pkts_compl, bytes_compl; +int ret, pkts_compl =0 , bytes_compl =0 , count =0 ; +struct mtk_star_priv *priv; +struct mtk_star_ring *ring; +struct net_device *ndev; +unsigned long flags =0 ; +unsigned int entry;bool wake = false; -spin_lock (&priv->lock); + priv = container_of(napi, struct mtk_star_priv, tx_napi); + ndev = priv->ndev;
Quoted 8 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c static int mtk_star_tx_complete_one(struct mtk_star_priv *priv) · line 1153
Quoted 2 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +1
-1- for (pkts_compl = 0, bytes_compl = 0;; +__netif_tx_lock_bh (netdev_get_tx_queue (priv->ndev,0 ));Do you really need to lock out the Tx while cleaning?
Drivers usually manage to implement concurrent Tx and cleanup with just
a couple of memory barriers.
We'll simplify the lock handling in next send,
the lock should protect tx descriptor ring, which is accessed by xmit() and tx_complete().
Quoted 8 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c static int mtk_star_tx_complete_one(struct mtk_star_priv *priv) · line 1157
Quoted 5 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +4
-0+ ring = &priv->tx_ring; + entry = ring->tail; + for (pkts_compl = 0, bytes_compl = 0; + (entry != ring->head) && (count < budget);budget is not really relevant for Tx, you can clean the whole ring. netpoll will pass a budget of 0 to clean up rings.
OK, will fix in next send.
Quoted 53 lines
Quoted 53 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +3
-3pkts_compl++, bytes_compl += ret, wake = true) { -if (!mtk_star_ring_descs_available (ring)) -break ; ret =mtk_star_tx_complete_one (priv);if (ret <0 )break ; + count++; + entry = ring->tail; }@@ -1196,7 +1258,7 @@ static const struct ethtool_ops mtk_star_ethtool_ops = { .set_link_ksettings = phy_ethtool_set_link_ksettings, }; -static int mtk_star_receive_packet (struct mtk_star_priv *priv) +static int mtk_star_rx (struct mtk_star_priv *priv,int budget) {struct mtk_star_ring *ring = &priv->rx_ring;drivers/net/ethernet/mediatek/mtk_star_emac.c +10
-11struct device *dev =mtk_star_get_dev (priv);@@ -1204,107 +1266,86 @@ static int mtk_star_receive_packet(struct mtk_star_priv *priv)struct net_device *ndev = priv->ndev;struct sk_buff *curr_skb, *new_skb;dma_addr_t new_dma_addr; -int ret; +int ret, count =0 ; -spin_lock (&priv->lock); - ret =mtk_star_ring_pop_tail (ring, &desc_data); -spin_unlock (&priv->lock); -if (ret) -return -1 ; +while (count < budget) { + ret =mtk_star_ring_pop_tail (ring, &desc_data); +if (ret) +return -1 ; -static int mtk_star_process_rx (struct mtk_star_priv *priv,int budget) -{ -int received, ret; + count++; -for (received =0 , ret =0 ; received < budget && ret ==0 ; received++) - ret =mtk_star_receive_packet (priv); + desc_data.len =skb_tailroom (new_skb); + desc_data.skb = new_skb; +mtk_star_ring_push_head_rx (ring, &desc_data); + }
Quoted 4 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c static int mtk_star_receive_packet(struct mtk_star_priv *priv) · line 1327
Quoted 1 line
drivers/net/ethernet/mediatek/mtk_star_emac.c +0
-0mtk_star_dma_resume_rx (priv);Again you can get a call with a budget of 0, not sure if it's okay to resume DMA in that case..
OK, we'll take it into consideration in next send.
Quoted 6 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c static int mtk_star_receive_packet(struct mtk_star_priv *priv) · line 1330
Quoted 4 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +1
-1-return received; +return count; }
Regards!
Biao
Jakub Kicinski
maintainerRe: [PATCH net-next v2 9/9] net: ethernet: mtk-star-emac: separate tx/rx handling with two NAPIs
Quoted 39 lines · On Fri, 28 Jan 2022 15:05:27 +0800 Biao Huang wrote:
Quoted 25 lines
Quoted 25 lines
+ * Description : this is the driver interrupt service routine.
+ * it mainly handles:+ * 1. tx complete interrupt for frame transmission. + * 2. rx complete interrupt for frame reception. + * 3. MAC Management Counter interrupt to avoid counter overflow.*/
staticirqreturn_tmtk_star_handle_irq(int irq, void *data){drivers/net/ethernet/mediatek/mtk_star_emac.c +14
-2-struct mtk_star_priv *priv; -struct net_device *ndev; +struct net_device *ndev = data; +struct mtk_star_priv *priv =netdev_priv (ndev); +unsigned int intr_status =mtk_star_intr_ack_all (priv); +unsigned long flags =0 ; + +if (intr_status &MTK_STAR_BIT_INT_STS_FNRC ) { +if (napi_schedule_prep (&priv->rx_napi)) { +spin_lock_irqsave (&priv->lock, flags); +/* mask Rx Complete interrupt */ +mtk_star_disable_dma_irq (priv, true, false); +spin_unlock_irqrestore (&priv->lock, flags); +__napi_schedule_irqoff (&priv->rx_napi); + } + }Quoted 14 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c static void mtk_star_free_tx_skbs(struct mtk_star_priv *priv) · line 793
Quoted 11 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +9
-2- ndev = data; - priv =netdev_priv (ndev); +if (intr_status &MTK_STAR_BIT_INT_STS_TNTC ) { +if (napi_schedule_prep (&priv->tx_napi)) { +spin_lock_irqsave (&priv->lock, flags); +/* mask Tx Complete interrupt */ +mtk_star_disable_dma_irq (priv, false, true); +spin_unlock_irqrestore (&priv->lock, flags); +__napi_schedule_irqoff (&priv->tx_napi); + } + }Seems a little wasteful to retake the same lock twice if two IRQ sources fire at the same time.
Quoted 4 lines
The TX/RX irq control bits are in the same register, but they are triggered independently.
So it seems necessary to protect the register access with a spin lock.
This is what I meant:
rx = (status & RX) && napi_schedule_prep(rx_napi); tx = (status & TX) && napi_schedule_prep(tx_napi);
if (rx || tx) {
spin_lock()
disable_irq(priv, rx, tx);
spin_unlock();
if (rx)
__napi_schedule_irqoff(rx_napi)
if (tx)
__napi_schedule_irqoff(tx_napi)
}Quoted 22 lines
Quoted 14 lines
Quoted 14 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +0
-2desc_data.dma_addr =mtk_star_dma_map_tx (priv, skb);if (dma_mapping_error (dev, desc_data.dma_addr))@@ -1050,18 +1103,10 @@ static int mtk_star_netdev_start_xmit(struct sk_buff *skb, desc_data.skb = skb; desc_data.len = skb->len; - -spin_lock_bh (&priv->lock);mtk_star_ring_push_head_tx (ring, &desc_data);netdev_sent_queue (ndev, skb->len);Quoted 8 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c static int mtk_star_netdev_start_xmit(struct sk_buff *skb, · line 1061
Quoted 2 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +0
-2-if (mtk_star_ring_full (ring)) -netif_stop_queue (ndev);Are you stopping the queue in advance somewhere else now? Did you only
test this with BQL enabled? Only place that stops the ring also prints
a loud warning now AFAICS..
Quoted 4 lines
No.
We modify the ring full condition, and will not invoke
netif_stop_queueif queue is already stopped.
I don't understand what you're saying.
Quoted 4 lines
Test pass no matter whether BQL is enabled or disabled.
It's much safer to judge queue is full or not at the beginning of
start_xmit()to avoid invalid setting.
Drivers are expected to stop their queues at the end of xmit routine if the ring can't accommodate another frame. It's more efficient to stop the queues early than have to put skbs already dequeued from the qdisc layer back into the qdiscs.
Re: [PATCH net-next v2 9/9] net: ethernet: mtk-star-emac: separate tx/rx handling with two NAPIs
Dear Jakub,
Thanks for your comments~
Quoted 56 lines · Jakub Kicinski
Quoted 45 lines · On Fri, 28 Jan 2022 15:05:27 +0800 Biao Huang wrote:
Quoted 28 lines
Quoted 28 lines
+ * Description : this is the driver interrupt service routine.
+ * it mainly handles:+ * 1. tx complete interrupt for frame transmission. + * 2. rx complete interrupt for frame reception. + * 3. MAC Management Counter interrupt to avoid counteroverflow.
*/
staticirqreturn_tmtk_star_handle_irq(int irq, void *data){drivers/net/ethernet/mediatek/mtk_star_emac.c +10
-2-struct mtk_star_priv *priv; -struct net_device *ndev; +struct net_device *ndev = data; +struct mtk_star_priv *priv =netdev_priv (ndev); +unsigned int intr_status =mtk_star_intr_ack_all (priv); +unsigned long flags =0 ; + +if (intr_status &MTK_STAR_BIT_INT_STS_FNRC ) { +if (napi_schedule_prep (&priv->rx_napi)) { +spin_lock_irqsave (&priv->lock, flags); +/* mask Rx Complete interrupt */ + mtk_star_disable_dma_irq(priv, true,false);
(quoted diff) +1
-0+ spin_unlock_irqrestore(&priv->lock,flags);
drivers/net/ethernet/mediatek/mtk_star_emac.c +3
-0+__napi_schedule_irqoff (&priv->rx_napi); + } + }Quoted 16 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c static void mtk_star_free_tx_skbs(struct mtk_star_priv *priv) · line 793
Quoted 13 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +5
-2- ndev = data; - priv =netdev_priv (ndev); +if (intr_status &MTK_STAR_BIT_INT_STS_TNTC ) { +if (napi_schedule_prep (&priv->tx_napi)) { +spin_lock_irqsave (&priv->lock, flags); +/* mask Tx Complete interrupt */ + mtk_star_disable_dma_irq(priv, false,true);
(quoted diff) +1
-0+ spin_unlock_irqrestore(&priv->lock,flags);
drivers/net/ethernet/mediatek/mtk_star_emac.c +3
-0+__napi_schedule_irqoff (&priv->tx_napi); + } + }Seems a little wasteful to retake the same lock twice if two IRQ sources fire at the same time.
Quoted 4 lines
The TX/RX irq control bits are in the same register, but they are triggered independently.
So it seems necessary to protect the register access with a spin lock.This is what I meant:
rx = (status & RX) &&
napi_schedule_prep(rx_napi); tx = (status & TX) &&napi_schedule_prep(tx_napi);
Quoted 10 lines
if (rx || tx) {
spin_lock()
disable_irq(priv, rx, tx);
spin_unlock();
if (rx)
__napi_schedule_irqoff(rx_napi)
if (tx)
__napi_schedule_irqoff(tx_napi)
}OK, We'll adopt your suggestion, and corresponding modification will be added in next send.
Quoted 36 lines
Quoted 23 lines
Quoted 14 lines
Quoted 14 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +0
-2desc_data.dma_addr =mtk_star_dma_map_tx (priv, skb);if (dma_mapping_error (dev, desc_data.dma_addr))@@ -1050,18 +1103,10 @@ static int mtk_star_netdev_start_xmit(struct sk_buff *skb, desc_data.skb = skb; desc_data.len = skb->len; - -spin_lock_bh (&priv->lock);mtk_star_ring_push_head_tx (ring, &desc_data);netdev_sent_queue (ndev, skb->len);Quoted 8 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c static int mtk_star_netdev_start_xmit(struct sk_buff *skb, · line 1061
Quoted 2 lines
drivers/net/ethernet/mediatek/mtk_star_emac.c +0
-2-if (mtk_star_ring_full (ring)) -netif_stop_queue (ndev);Are you stopping the queue in advance somewhere else now? Did you only
test this with BQL enabled? Only place that stops the ring also prints
a loud warning now AFAICS..Quoted 5 lines
No.
We modify the ring full condition, and will not invoke
netif_stop_queue
if queue is already stopped.I don't understand what you're saying.
Quoted 4 lines
Test pass no matter whether BQL is enabled or disabled.
It's much safer to judge queue is full or not at the beginning of
start_xmit()to avoid invalid setting.
Quoted 6 lines
Drivers are expected to stop their queues at the end of xmit routine if
the ring can't accommodate another frame. It's more efficient to stop the queues early than have to put skbs already dequeued from the qdisc
layer back into the qdiscs.
Yes, if descriptors ring is full, it's meaningful to stop the queue at the end of xmit;
But driver seems hard to know how many descriptors the next skb will request, e.g. 3 descriptors are available for next round send, but the next skb may need 4 descriptors, in this case, we still need judge whether descriptors are enough for skb transmission, then decide stop the queue or not, at the beginning of xmit routine.
Maybe we should judge ring is full or not at the beginning and the end of xmit routine(seems a little redundancy).
Regards~
Jakub Kicinski
maintainerRe: [PATCH net-next v2 9/9] net: ethernet: mtk-star-emac: separate tx/rx handling with two NAPIs
Quoted 14 lines · On Mon, 14 Mar 2022 15:01:23 +0800 Biao Huang wrote:
Quoted 6 lines
Drivers are expected to stop their queues at the end of xmit routine if
the ring can't accommodate another frame. It's more efficient to stop the queues early than have to put skbs already dequeued from the qdisc
layer back into the qdiscs.Yes, if descriptors ring is full, it's meaningful to stop the queue at the end of xmit;
But driver seems hard to know how many descriptors the next skb will request, e.g. 3 descriptors are available for next round send, but the next skb may need 4 descriptors, in this case, we still need judge whether descriptors are enough for skb transmission, then decide stop the queue or not, at the beginning of xmit routine.
Quoted 2 lines
Maybe we should judge ring is full or not at the beginning and the end of xmit routine(seems a little redundancy).
Assume the worst case scenario. You set the default ring size to 512, skb can have at most MAX_SKB_FRAGS fragments (usually 17) so the max number of descriptors should not be very high, hard to pre-compute, or problematic compared to the total ring size.
Re: [PATCH net-next v2 9/9] net: ethernet: mtk-star-emac: separate tx/rx handling with two NAPIs
Dear Jakub,
Thanks for your comments~
Quoted 22 lines · Jakub Kicinski
Quoted 21 lines · On Mon, 14 Mar 2022 15:01:23 +0800 Biao Huang wrote:
Quoted 8 lines
Drivers are expected to stop their queues at the end of xmit routine
if
the ring can't accommodate another frame. It's more efficient to stop
the queues early than have to put skbs already dequeued from the qdisc
layer back into the qdiscs.Yes, if descriptors ring is full, it's meaningful to stop the queue
at the end of xmit;
But driver seems hard to know how many descriptors the next skb will
request, e.g. 3 descriptors are available for next round send, but the
next skb may need 4 descriptors, in this case, we still need judge whether descriptors are enough for skb transmission, then decide stop
the queue or not, at the beginning of xmit routine.
Quoted 8 lines
Quoted 3 lines
Maybe we should judge ring is full or not at the beginning and the end
of xmit routine(seems a little redundancy).Assume the worst case scenario. You set the default ring size to 512, skb can have at most
MAX_SKB_FRAGSfragments (usually 17) so the max number of descriptors should not be very high, hard to pre-compute, or problematic compared to the total ring size.
Yes, we'll check the available descriptor number at the end of xmit routine, and ensure it will larger than (MAX_SKB_FRAGS + 1) in next send. (refer to stmmac_main.c)
Regards!