Skip to contentSkip to conversation

Splitting HAS_PCH_SPLIT code in intel_crtc_mode_set().

PATCH In review Eric Anholt 3 participants 21 messages Mar 30, 2011 – Mar 31, 2011

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

In doing new chipset enablement for the first time in quite a while, it sunk in just how bad the spaghetti in our modeset path was these days. I think that splitting the crtc_mode_set up a bit gets us a more readable path for whichever generation you're trying to look at, while not duplicating too much code -- note that patch 1/9 is +675 LOC, while after 8/9 we're down to +299 overall.

To atone for about +300LOC, patch 9/9 does another cleanup I think is appropriate and cuts almost 300 lines of used-once #define spam.

This is only tested on my Ironlake so far, and only for LVDS.

#1 lore raw

PATCH 1/9 drm/i915: Split the crtc_mode_set function along HAS_PCH_SPLIT() lines.

This path, which shouldn't be *that* complicated, is now so littered with per-chipset tweaks that it's hard to trace the order of what happens. HAS_PCH_SPLIT() is the most radical change across chipsets, so it seems like a natural split to simplify the code.

This first commit just copies the existing code without changing anything.

---
 drivers/gpu/drm/i915/i915_drv.h      |    6 +
 drivers/gpu/drm/i915/intel_display.c |  683 +++++++++++++++++++++++++++++++++-
 2 files changed, 682 insertions(+), 7 deletions(-)
drivers/gpu/drm/i915/i915_drv.h +6 -0
index e38765d..2f45228 100644
@@ -203,6 +203,12 @@ struct drm_i915_display_funcs {
 	int (*get_display_clock_speed)(struct drm_device *dev);
 	int (*get_fifo_size)(struct drm_device *dev, int plane);
 	void (*update_wm)(struct drm_device *dev);
+	int (*crtc_mode_set)(struct drm_crtc *crtc,
+			     struct drm_display_mode *mode,
+			     struct drm_display_mode *adjusted_mode,
+			     int x, int y,
+			     struct drm_framebuffer *old_fb);
+
 	/* clock updates for mode set */
 	/* cursor updates */
 	/* render clock increase/decrease */
drivers/gpu/drm/i915/intel_display.c +676 -7

703 lines not on this page · raw message

Signature · 1 line
1.7.4.1
#2 lore raw

Re: [PATCH 1/9] drm/i915: Split the crtc_mode_set function along HAS_PCH_SPLIT() lines.

Quoted 10 lines · On Wed, 30 Mar 2011 13:01:02 -0700 Eric Anholt <[email protected]> wrote:

This path, which shouldn't be *that* complicated, is now so littered with per-chipset tweaks that it's hard to trace the order of what happens. HAS_PCH_SPLIT() is the most radical change across chipsets, so it seems like a natural split to simplify the code.

This first commit just copies the existing code without changing anything.

---

Signature · 1 line
Jesse Barnes, Intel Open Source Technology Center
#3 lore raw

PATCH 2/9 drm/i915: Move the vblank pre/post modeset to the common crtc_mode_set.

In reply to Eric Anholt
---
 drivers/gpu/drm/i915/intel_display.c |   16 ++++++----------
 1 files changed, 6 insertions(+), 10 deletions(-)
drivers/gpu/drm/i915/intel_display.c +6 -10
index 610363c..7b2cd8a 100644
@@ -4540,8 +4540,6 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 	u32 lvds_sync = 0;
 	int target_clock;
 
-	drm_vblank_pre_modeset(dev, pipe);
-
 	list_for_each_entry(encoder, &mode_config->encoder_list, base.head) {
 		if (encoder->base.crtc != crtc)
 			continue;
@@ -4598,7 +4596,6 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 	ok = limit->find_pll(limit, crtc, adjusted_mode->clock, refclk, &clock);
 	if (!ok) {
 		DRM_ERROR("Couldn't find PLL settings for mode!\n");
-		drm_vblank_post_modeset(dev, pipe);
 		return -EINVAL;
 	}
 
@@ -5158,8 +5155,6 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 
 	intel_update_watermarks(dev);
 
-	drm_vblank_post_modeset(dev, pipe);
-
 	return ret;
 }
 
@@ -5190,8 +5185,6 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 	u32 lvds_sync = 0;
 	int target_clock;
 
-	drm_vblank_pre_modeset(dev, pipe);
-
 	list_for_each_entry(encoder, &mode_config->encoder_list, base.head) {
 		if (encoder->base.crtc != crtc)
 			continue;
@@ -5248,7 +5241,6 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 	ok = limit->find_pll(limit, crtc, adjusted_mode->clock, refclk, &clock);
 	if (!ok) {
 		DRM_ERROR("Couldn't find PLL settings for mode!\n");
-		drm_vblank_post_modeset(dev, pipe);
 		return -EINVAL;
 	}
 
@@ -5808,8 +5800,6 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 
 	intel_update_watermarks(dev);
 
-	drm_vblank_post_modeset(dev, pipe);
-
 	return ret;
 }
 
@@ -5821,11 +5811,17 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc,
 {
 	struct drm_device *dev = crtc->dev;
 	struct drm_i915_private *dev_priv = dev->dev_private;
+	struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
+	int pipe = intel_crtc->pipe;
 	int ret;
 
+	drm_vblank_pre_modeset(dev, pipe);
+
 	ret = dev_priv->display.crtc_mode_set(crtc, mode, adjusted_mode,
 					      x, y, old_fb);
 
+	drm_vblank_post_modeset(dev, pipe);
+
 	return ret;
 }
 
Signature · 1 line
1.7.4.1
#5 lore raw

PATCH 3/9 drm/i915: Remove the PCH paths from the pre-Ironlake crtc_mode_set().

In reply to Eric Anholt
---
 drivers/gpu/drm/i915/intel_display.c |  284 +++-------------------------------
 1 files changed, 24 insertions(+), 260 deletions(-)
drivers/gpu/drm/i915/intel_display.c +24 -260
index 7b2cd8a..d955646 100644
@@ -4535,10 +4535,8 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 	struct intel_encoder *encoder;
 	const intel_limit_t *limit;
 	int ret;
-	struct fdi_m_n m_n = {0};
 	u32 reg, temp;
 	u32 lvds_sync = 0;
-	int target_clock;
 
 	list_for_each_entry(encoder, &mode_config->encoder_list, base.head) {
 		if (encoder->base.crtc != crtc)
@@ -4580,9 +4578,6 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 			      refclk / 1000);
 	} else if (!IS_GEN2(dev)) {
 		refclk = 96000;
-		if (HAS_PCH_SPLIT(dev) &&
-		    (!has_edp_encoder || intel_encoder_is_pch_edp(&has_edp_encoder->base)))
-			refclk = 120000; /* 120Mhz refclk */
 	} else {
 		refclk = 48000;
 	}
@@ -4639,143 +4634,6 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 		}
 	}
 
-	/* FDI link */
-	if (HAS_PCH_SPLIT(dev)) {
-		int pixel_multiplier = intel_mode_get_pixel_multiplier(adjusted_mode);
-		int lane = 0, link_bw, bpp;
-		/* CPU eDP doesn't require FDI link, so just set DP M/N
-		   according to current link config */
-		if (has_edp_encoder && !intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
-			target_clock = mode->clock;
-			intel_edp_link_config(has_edp_encoder,
-					      &lane, &link_bw);
-		} else {
-			/* [e]DP over FDI requires target mode clock
-			   instead of link clock */
-			if (is_dp || intel_encoder_is_pch_edp(&has_edp_encoder->base))
-				target_clock = mode->clock;
-			else
-				target_clock = adjusted_mode->clock;
-
-			/* FDI is a binary signal running at ~2.7GHz, encoding
-			 * each output octet as 10 bits. The actual frequency
-			 * is stored as a divider into a 100MHz clock, and the
-			 * mode pixel clock is stored in units of 1KHz.
-			 * Hence the bw of each lane in terms of the mode signal
-			 * is:
-			 */
-			link_bw = intel_fdi_link_freq(dev) * MHz(100)/KHz(1)/10;
-		}
-
-		/* determine panel color depth */
-		temp = I915_READ(PIPECONF(pipe));
-		temp &= ~PIPE_BPC_MASK;
-		if (is_lvds) {
-			/* the BPC will be 6 if it is 18-bit LVDS panel */
-			if ((I915_READ(PCH_LVDS) & LVDS_A3_POWER_MASK) == LVDS_A3_POWER_UP)
-				temp |= PIPE_8BPC;
-			else
-				temp |= PIPE_6BPC;
-		} else if (has_edp_encoder) {
-			switch (dev_priv->edp.bpp/3) {
-			case 8:
-				temp |= PIPE_8BPC;
-				break;
-			case 10:
-				temp |= PIPE_10BPC;
-				break;
-			case 6:
-				temp |= PIPE_6BPC;
-				break;
-			case 12:
-				temp |= PIPE_12BPC;
-				break;
-			}
-		} else
-			temp |= PIPE_8BPC;
-		I915_WRITE(PIPECONF(pipe), temp);
-
-		switch (temp & PIPE_BPC_MASK) {
-		case PIPE_8BPC:
-			bpp = 24;
-			break;
-		case PIPE_10BPC:
-			bpp = 30;
-			break;
-		case PIPE_6BPC:
-			bpp = 18;
-			break;
-		case PIPE_12BPC:
-			bpp = 36;
-			break;
-		default:
-			DRM_ERROR("unknown pipe bpc value\n");
-			bpp = 24;
-		}
-
-		if (!lane) {
-			/*
-			 * Account for spread spectrum to avoid
-			 * oversubscribing the link. Max center spread
-			 * is 2.5%; use 5% for safety's sake.
-			 */
-			u32 bps = target_clock * bpp * 21 / 20;
-			lane = bps / (link_bw * 8) + 1;
-		}
-
-		intel_crtc->fdi_lanes = lane;
-
-		if (pixel_multiplier > 1)
-			link_bw *= pixel_multiplier;
-		ironlake_compute_m_n(bpp, lane, target_clock, link_bw, &m_n);
-	}
-
-	/* Ironlake: try to setup display ref clock before DPLL
-	 * enabling. This is only under driver's control after
-	 * PCH B stepping, previous chipset stepping should be
-	 * ignoring this setting.
-	 */
-	if (HAS_PCH_SPLIT(dev)) {
-		temp = I915_READ(PCH_DREF_CONTROL);
-		/* Always enable nonspread source */
-		temp &= ~DREF_NONSPREAD_SOURCE_MASK;
-		temp |= DREF_NONSPREAD_SOURCE_ENABLE;
-		temp &= ~DREF_SSC_SOURCE_MASK;
-		temp |= DREF_SSC_SOURCE_ENABLE;
-		I915_WRITE(PCH_DREF_CONTROL, temp);
-
-		POSTING_READ(PCH_DREF_CONTROL);
-		udelay(200);
-
-		if (has_edp_encoder) {
-			if (intel_panel_use_ssc(dev_priv)) {
-				temp |= DREF_SSC1_ENABLE;
-				I915_WRITE(PCH_DREF_CONTROL, temp);
-
-				POSTING_READ(PCH_DREF_CONTROL);
-				udelay(200);
-			}
-			temp &= ~DREF_CPU_SOURCE_OUTPUT_MASK;
-
-			/* Enable CPU source on CPU attached eDP */
-			if (!intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
-				if (intel_panel_use_ssc(dev_priv))
-					temp |= DREF_CPU_SOURCE_OUTPUT_DOWNSPREAD;
-				else
-					temp |= DREF_CPU_SOURCE_OUTPUT_NONSPREAD;
-			} else {
-				/* Enable SSC on PCH eDP if needed */
-				if (intel_panel_use_ssc(dev_priv)) {
-					DRM_ERROR("enabling SSC on PCH\n");
-					temp |= DREF_SUPERSPREAD_SOURCE_ENABLE;
-				}
-			}
-			I915_WRITE(PCH_DREF_CONTROL, temp);
-			POSTING_READ(PCH_DREF_CONTROL);
-			udelay(200);
-		}
-	}
-
 	if (IS_PINEVIEW(dev)) {
 		fp = (1 << clock.n) << 16 | clock.m1 << 8 | clock.m2;
 		if (has_reduced_clock)
@@ -4788,25 +4646,7 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 				reduced_clock.m2;
 	}
 
-	/* Enable autotuning of the PLL clock (if permissible) */
-	if (HAS_PCH_SPLIT(dev)) {
-		int factor = 21;
-
-		if (is_lvds) {
-			if ((intel_panel_use_ssc(dev_priv) &&
-			     dev_priv->lvds_ssc_freq == 100) ||
-			    (I915_READ(PCH_LVDS) & LVDS_CLKB_POWER_MASK) == LVDS_CLKB_POWER_UP)
-				factor = 25;
-		} else if (is_sdvo && is_tv)
-			factor = 20;
-
-		if (clock.m1 < factor * clock.n)
-			fp |= FP_CB_TUNE;
-	}
-
-	dpll = 0;
-	if (!HAS_PCH_SPLIT(dev))
-		dpll = DPLL_VGA_MODE_DIS;
+	dpll = DPLL_VGA_MODE_DIS;
 
 	if (!IS_GEN2(dev)) {
 		if (is_lvds)
@@ -4818,12 +4658,10 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 			if (pixel_multiplier > 1) {
 				if (IS_I945G(dev) || IS_I945GM(dev) || IS_G33(dev))
 					dpll |= (pixel_multiplier - 1) << SDVO_MULTIPLIER_SHIFT_HIRES;
-				else if (HAS_PCH_SPLIT(dev))
-					dpll |= (pixel_multiplier - 1) << PLL_REF_SDVO_HDMI_MULTIPLIER_SHIFT;
 			}
 			dpll |= DPLL_DVO_HIGH_SPEED;
 		}
-		if (is_dp || intel_encoder_is_pch_edp(&has_edp_encoder->base))
+		if (is_dp)
 			dpll |= DPLL_DVO_HIGH_SPEED;
 
 		/* compute bitmask from p1 value */
@@ -4831,9 +4669,6 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 			dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT_PINEVIEW;
 		else {
 			dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT;
-			/* also FPA1 */
-			if (HAS_PCH_SPLIT(dev))
-				dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA1_P1_POST_DIV_SHIFT;
 			if (IS_G4X(dev) && has_reduced_clock)
 				dpll |= (1 << (reduced_clock.p1 - 1)) << DPLL_FPA1_P1_POST_DIV_SHIFT;
 		}
@@ -4851,7 +4686,7 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 			dpll |= DPLLB_LVDS_P2_CLOCK_DIV_14;
 			break;
 		}
-		if (INTEL_INFO(dev)->gen >= 4 && !HAS_PCH_SPLIT(dev))
+		if (INTEL_INFO(dev)->gen >= 4)
 			dpll |= (6 << PLL_LOAD_PULSE_PHASE_SHIFT);
 	} else {
 		if (is_lvds) {
@@ -4885,12 +4720,10 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 
 	/* Ironlake's plane is forced to pipe, bit 24 is to
 	   enable color space conversion */
-	if (!HAS_PCH_SPLIT(dev)) {
-		if (pipe == 0)
-			dspcntr &= ~DISPPLANE_SEL_PIPE_MASK;
-		else
-			dspcntr |= DISPPLANE_SEL_PIPE_B;
-	}
+	if (pipe == 0)
+		dspcntr &= ~DISPPLANE_SEL_PIPE_MASK;
+	else
+		dspcntr |= DISPPLANE_SEL_PIPE_B;
 
 	if (pipe == 0 && INTEL_INFO(dev)->gen < 4) {
 		/* Enable pixel doubling when the dot clock is > 90% of the (display)
@@ -4906,23 +4739,16 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 			pipeconf &= ~PIPECONF_DOUBLE_WIDE;
 	}
 
-	if (!HAS_PCH_SPLIT(dev))
-		dpll |= DPLL_VCO_ENABLE;
+	dpll |= DPLL_VCO_ENABLE;
 
 	DRM_DEBUG_KMS("Mode for pipe %c:\n", pipe == 0 ? 'A' : 'B');
 	drm_mode_debug_printmodeline(mode);
 
-	/* assign to Ironlake registers */
-	if (HAS_PCH_SPLIT(dev)) {
-		fp_reg = PCH_FP0(pipe);
-		dpll_reg = PCH_DPLL(pipe);
-	} else {
-		fp_reg = FP0(pipe);
-		dpll_reg = DPLL(pipe);
-	}
+	fp_reg = FP0(pipe);
+	dpll_reg = DPLL(pipe);
 
 	/* PCH eDP needs FDI, but CPU eDP does not */
-	if (!has_edp_encoder || intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
+	if (!has_edp_encoder) {
 		I915_WRITE(fp_reg, fp);
 		I915_WRITE(dpll_reg, dpll & ~DPLL_VCO_ENABLE);
 
@@ -4930,50 +4756,19 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 		udelay(150);
 	}
 
-	/* enable transcoder DPLL */
-	if (HAS_PCH_CPT(dev)) {
-		temp = I915_READ(PCH_DPLL_SEL);
-		switch (pipe) {
-		case 0:
-			temp |= TRANSA_DPLL_ENABLE | TRANSA_DPLLA_SEL;
-			break;
-		case 1:
-			temp |=	TRANSB_DPLL_ENABLE | TRANSB_DPLLB_SEL;
-			break;
-		case 2:
-			/* FIXME: manage transcoder PLLs? */
-			temp |= TRANSC_DPLL_ENABLE | TRANSC_DPLLB_SEL;
-			break;
-		default:
-			BUG();
-		}
-		I915_WRITE(PCH_DPLL_SEL, temp);
-
-		POSTING_READ(PCH_DPLL_SEL);
-		udelay(150);
-	}
-
 	/* The LVDS pin pair needs to be on before the DPLLs are enabled.
 	 * This is an exception to the general rule that mode_set doesn't turn
 	 * things on.
 	 */
 	if (is_lvds) {
 		reg = LVDS;
-		if (HAS_PCH_SPLIT(dev))
-			reg = PCH_LVDS;
 
 		temp = I915_READ(reg);
 		temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
 		if (pipe == 1) {
-			if (HAS_PCH_CPT(dev))
-				temp |= PORT_TRANS_B_SEL_CPT;
-			else
-				temp |= LVDS_PIPEB_SELECT;
+			temp |= LVDS_PIPEB_SELECT;
 		} else {
-			if (HAS_PCH_CPT(dev))
-				temp &= ~PORT_TRANS_SEL_MASK;
-			else
-				temp &= ~LVDS_PIPEB_SELECT;
+			temp &= ~LVDS_PIPEB_SELECT;
 		}
 		/* set the corresponsding LVDS_BORDER bit */
 		temp |= dev_priv->lvds_border_bits;
@@ -4989,8 +4784,8 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 		 * appropriately here, but we need to look more thoroughly into how
 		 * panels behave in the two modes.
 		 */
-		/* set the dithering flag on non-PCH LVDS as needed */
-		if (INTEL_INFO(dev)->gen >= 4 && !HAS_PCH_SPLIT(dev)) {
+		/* set the dithering flag on LVDS as needed */
+		if (INTEL_INFO(dev)->gen >= 4) {
 			if (dev_priv->lvds_dither)
 				temp |= LVDS_ENABLE_DITHER;
 			else
@@ -5015,34 +4810,18 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 		I915_WRITE(reg, temp);
 	}
 
-	/* set the dithering flag and clear for anything other than a panel. */
-	if (HAS_PCH_SPLIT(dev)) {
-		pipeconf &= ~PIPECONF_DITHER_EN;
-		pipeconf &= ~PIPECONF_DITHER_TYPE_MASK;
-		if (dev_priv->lvds_dither && (is_lvds || has_edp_encoder)) {
-			pipeconf |= PIPECONF_DITHER_EN;
-			pipeconf |= PIPECONF_DITHER_TYPE_ST1;
-		}
-	}
-
-	if (is_dp || intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
+	if (is_dp) {
 		intel_dp_set_m_n(crtc, mode, adjusted_mode);
-	} else if (HAS_PCH_SPLIT(dev)) {
-		/* For non-DP output, clear any trans DP clock recovery setting.*/
-		I915_WRITE(TRANSDATA_M1(pipe), 0);
-		I915_WRITE(TRANSDATA_N1(pipe), 0);
-		I915_WRITE(TRANSDPLINK_M1(pipe), 0);
-		I915_WRITE(TRANSDPLINK_N1(pipe), 0);
 	}
 
-	if (!has_edp_encoder || intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
+	if (!has_edp_encoder) {
 		I915_WRITE(dpll_reg, dpll);
 
 		/* Wait for the clocks to stabilize. */
 		POSTING_READ(dpll_reg);
 		udelay(150);
 
-		if (INTEL_INFO(dev)->gen >= 4 && !HAS_PCH_SPLIT(dev)) {
+		if (INTEL_INFO(dev)->gen >= 4) {
 			temp = 0;
 			if (is_sdvo) {
 				temp = intel_mode_get_pixel_multiplier(adjusted_mode);
@@ -5113,30 +4892,16 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 	/* pipesrc and dspsize control the size that is scaled from,
 	 * which should always be the user's requested size.
 	 */
-	if (!HAS_PCH_SPLIT(dev)) {
-		I915_WRITE(DSPSIZE(plane),
-			   ((mode->vdisplay - 1) << 16) |
-			   (mode->hdisplay - 1));
-		I915_WRITE(DSPPOS(plane), 0);
-	}
+	I915_WRITE(DSPSIZE(plane),
+		   ((mode->vdisplay - 1) << 16) |
+		   (mode->hdisplay - 1));
+	I915_WRITE(DSPPOS(plane), 0);
 	I915_WRITE(PIPESRC(pipe),
 		   ((mode->hdisplay - 1) << 16) | (mode->vdisplay - 1));
 
-	if (HAS_PCH_SPLIT(dev)) {
-		I915_WRITE(PIPE_DATA_M1(pipe), TU_SIZE(m_n.tu) | m_n.gmch_m);
-		I915_WRITE(PIPE_DATA_N1(pipe), m_n.gmch_n);
-		I915_WRITE(PIPE_LINK_M1(pipe), m_n.link_m);
-		I915_WRITE(PIPE_LINK_N1(pipe), m_n.link_n);
-
-		if (has_edp_encoder && !intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
-			ironlake_set_pll_edp(crtc, adjusted_mode->clock);
-		}
-	}
-
 	I915_WRITE(PIPECONF(pipe), pipeconf);
 	POSTING_READ(PIPECONF(pipe));
-	if (!HAS_PCH_SPLIT(dev))
-		intel_enable_pipe(dev_priv, pipe, false);
+	intel_enable_pipe(dev_priv, pipe, false);
 
 	intel_wait_for_vblank(dev, pipe);
 
@@ -5148,8 +4913,7 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 
 	I915_WRITE(DSPCNTR(plane), dspcntr);
 	POSTING_READ(DSPCNTR(plane));
-	if (!HAS_PCH_SPLIT(dev))
-		intel_enable_plane(dev_priv, plane, pipe);
+	intel_enable_plane(dev_priv, plane, pipe);
 
 	ret = intel_pipe_set_base(crtc, x, y, old_fb);
 
Signature · 1 line
1.7.4.1
Reviewed-by on v1 3/9
#6 lore raw

Re: [PATCH 3/9] drm/i915: Remove the PCH paths from the pre-Ironlake crtc_mode_set().

Quoted 4 lines · On Wed, 30 Mar 2011 13:01:04 -0700 Eric Anholt <[email protected]> wrote:
---
 drivers/gpu/drm/i915/intel_display.c |  284 +++-------------------------------
 1 files changed, 24 insertions(+), 260 deletions(-)

Was going to suggest you also drop the eDP paths, but I see you got that in the next patch.

Signature · 1 line
Jesse Barnes, Intel Open Source Technology Center
#7 lore raw

PATCH 4/9 drm/i915: Drop the eDP paths from the pre-Ironlake crtc_mode_set.

In reply to Eric Anholt

While g4x had DP, eDP came with Ironlake, so we don't need that code here.

---
 drivers/gpu/drm/i915/intel_display.c |   57 ++++++++++++++-------------------
 1 files changed, 24 insertions(+), 33 deletions(-)
drivers/gpu/drm/i915/intel_display.c +24 -33
index d955646..309ea47 100644
@@ -4530,7 +4530,6 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 	u32 dpll, fp = 0, fp2 = 0, dspcntr, pipeconf;
 	bool ok, has_reduced_clock = false, is_sdvo = false, is_dvo = false;
 	bool is_crt = false, is_lvds = false, is_tv = false, is_dp = false;
-	struct intel_encoder *has_edp_encoder = NULL;
 	struct drm_mode_config *mode_config = &dev->mode_config;
 	struct intel_encoder *encoder;
 	const intel_limit_t *limit;
@@ -4564,9 +4563,6 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 		case INTEL_OUTPUT_DISPLAYPORT:
 			is_dp = true;
 			break;
-		case INTEL_OUTPUT_EDP:
-			has_edp_encoder = encoder;
-			break;
 		}
 
 		num_connectors++;
@@ -4747,14 +4743,11 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 	fp_reg = FP0(pipe);
 	dpll_reg = DPLL(pipe);
 
-	/* PCH eDP needs FDI, but CPU eDP does not */
-	if (!has_edp_encoder) {
-		I915_WRITE(fp_reg, fp);
-		I915_WRITE(dpll_reg, dpll & ~DPLL_VCO_ENABLE);
+	I915_WRITE(fp_reg, fp);
+	I915_WRITE(dpll_reg, dpll & ~DPLL_VCO_ENABLE);
 
-		POSTING_READ(dpll_reg);
-		udelay(150);
-	}
+	POSTING_READ(dpll_reg);
+	udelay(150);
 
 	/* The LVDS pin pair needs to be on before the DPLLs are enabled.
 	 * This is an exception to the general rule that mode_set doesn't turn
@@ -4814,31 +4807,29 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 		intel_dp_set_m_n(crtc, mode, adjusted_mode);
 	}
 
-	if (!has_edp_encoder) {
-		I915_WRITE(dpll_reg, dpll);
+	I915_WRITE(dpll_reg, dpll);
 
-		/* Wait for the clocks to stabilize. */
-		POSTING_READ(dpll_reg);
-		udelay(150);
+	/* Wait for the clocks to stabilize. */
+	POSTING_READ(dpll_reg);
+	udelay(150);
 
-		if (INTEL_INFO(dev)->gen >= 4) {
-			temp = 0;
-			if (is_sdvo) {
-				temp = intel_mode_get_pixel_multiplier(adjusted_mode);
-				if (temp > 1)
-					temp = (temp - 1) << DPLL_MD_UDI_MULTIPLIER_SHIFT;
-				else
-					temp = 0;
-			}
-			I915_WRITE(DPLL_MD(pipe), temp);
-		} else {
-			/* The pixel multiplier can only be updated once the
-			 * DPLL is enabled and the clocks are stable.
-			 *
-			 * So write it again.
-			 */
-			I915_WRITE(dpll_reg, dpll);
+	if (INTEL_INFO(dev)->gen >= 4) {
+		temp = 0;
+		if (is_sdvo) {
+			temp = intel_mode_get_pixel_multiplier(adjusted_mode);
+			if (temp > 1)
+				temp = (temp - 1) << DPLL_MD_UDI_MULTIPLIER_SHIFT;
+			else
+				temp = 0;
 		}
+		I915_WRITE(DPLL_MD(pipe), temp);
+	} else {
+		/* The pixel multiplier can only be updated once the
+		 * DPLL is enabled and the clocks are stable.
+		 *
+		 * So write it again.
+		 */
+		I915_WRITE(dpll_reg, dpll);
 	}
 
 	intel_crtc->lowfreq_avail = false;
Signature · 1 line
1.7.4.1
#9 lore raw

PATCH 5/9 drm/i915: Drop the remaining bit of Ironlake code from i9xx_crtc_mode_set().

In reply to Eric Anholt
---
 drivers/gpu/drm/i915/intel_display.c |    6 ------
 1 files changed, 0 insertions(+), 6 deletions(-)
drivers/gpu/drm/i915/intel_display.c +0 -6
index 309ea47..4254228 100644
@@ -4896,12 +4896,6 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 
 	intel_wait_for_vblank(dev, pipe);
 
-	if (IS_GEN5(dev)) {
-		/* enable address swizzle for tiling buffer */
-		temp = I915_READ(DISP_ARB_CTL);
-		I915_WRITE(DISP_ARB_CTL, temp | DISP_TILE_SURFACE_SWIZZLING);
-	}
-
 	I915_WRITE(DSPCNTR(plane), dspcntr);
 	POSTING_READ(DSPCNTR(plane));
 	intel_enable_plane(dev_priv, plane, pipe);
Signature · 1 line
1.7.4.1
Reviewed-by on v1 5/9
#10 lore raw

Re: [PATCH 5/9] drm/i915: Drop the remaining bit of Ironlake code from i9xx_crtc_mode_set().

Quoted 12 lines · On Wed, 30 Mar 2011 13:01:06 -0700 Eric Anholt <[email protected]> wrote:
---
 drivers/gpu/drm/i915/intel_display.c |    6 ------
 1 files changed, 0 insertions(+), 6 deletions(-)
drivers/gpu/drm/i915/intel_display.c +0 -0
index 309ea47..4254228 100644
@@ -4896,12 +4896,6 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 
 	intel_wait_for_vblank(dev, pipe);

drivers/gpu/drm/i915/intel_display.c static int i9xx_crtc_mode_set(struct drm_crtc *crtc, · line 4901

Quoted 10 lines
drivers/gpu/drm/i915/intel_display.c +0 -6
 
-	if (IS_GEN5(dev)) {
-		/* enable address swizzle for tiling buffer */
-		temp = I915_READ(DISP_ARB_CTL);
-		I915_WRITE(DISP_ARB_CTL, temp | DISP_TILE_SURFACE_SWIZZLING);
-	}
-
 	I915_WRITE(DSPCNTR(plane), dspcntr);
 	POSTING_READ(DSPCNTR(plane));
 	intel_enable_plane(dev_priv, plane, pipe);
Signature · 1 line
Jesse Barnes, Intel Open Source Technology Center
#11 lore raw

PATCH 6/9 drm/i915: Drop non-HAS_PCH_SPLIT() code from ironlake_crtc_mode_set().

In reply to Eric Anholt

Ironlake is where the PCH split started.

---
 drivers/gpu/drm/i915/intel_display.c |  361 ++++++++++++++--------------------
 1 files changed, 150 insertions(+), 211 deletions(-)
drivers/gpu/drm/i915/intel_display.c +150 -211
index 4254228..496bee9 100644
@@ -4932,7 +4932,7 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 	struct fdi_m_n m_n = {0};
 	u32 reg, temp;
 	u32 lvds_sync = 0;
-	int target_clock;
+	int target_clock, pixel_multiplier, lane, link_bw, bpp, factor;
 
 	list_for_each_entry(encoder, &mode_config->encoder_list, base.head) {
 		if (encoder->base.crtc != crtc)
@@ -4974,8 +4974,8 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 			      refclk / 1000);
 	} else if (!IS_GEN2(dev)) {
 		refclk = 96000;
-		if (HAS_PCH_SPLIT(dev) &&
-		    (!has_edp_encoder || intel_encoder_is_pch_edp(&has_edp_encoder->base)))
+		if (!has_edp_encoder ||
+		    intel_encoder_is_pch_edp(&has_edp_encoder->base))
 			refclk = 120000; /* 120Mhz refclk */
 	} else {
 		refclk = 48000;
@@ -5034,140 +5034,137 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 	}
 
 	/* FDI link */
-	if (HAS_PCH_SPLIT(dev)) {
-		int pixel_multiplier = intel_mode_get_pixel_multiplier(adjusted_mode);
-		int lane = 0, link_bw, bpp;
-		/* CPU eDP doesn't require FDI link, so just set DP M/N
-		   according to current link config */
-		if (has_edp_encoder && !intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
+	pixel_multiplier = intel_mode_get_pixel_multiplier(adjusted_mode);
+	lane = 0;
+	/* CPU eDP doesn't require FDI link, so just set DP M/N
+	   according to current link config */
+	if (has_edp_encoder &&
+	    !intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
+		target_clock = mode->clock;
+		intel_edp_link_config(has_edp_encoder,
+				      &lane, &link_bw);
+	} else {
+		/* [e]DP over FDI requires target mode clock
+		   instead of link clock */
+		if (is_dp || intel_encoder_is_pch_edp(&has_edp_encoder->base))
 			target_clock = mode->clock;
-			intel_edp_link_config(has_edp_encoder,
-					      &lane, &link_bw);
-		} else {
-			/* [e]DP over FDI requires target mode clock
-			   instead of link clock */
-			if (is_dp || intel_encoder_is_pch_edp(&has_edp_encoder->base))
-				target_clock = mode->clock;
-			else
-				target_clock = adjusted_mode->clock;
-
-			/* FDI is a binary signal running at ~2.7GHz, encoding
-			 * each output octet as 10 bits. The actual frequency
-			 * is stored as a divider into a 100MHz clock, and the
-			 * mode pixel clock is stored in units of 1KHz.
-			 * Hence the bw of each lane in terms of the mode signal
-			 * is:
-			 */
-			link_bw = intel_fdi_link_freq(dev) * MHz(100)/KHz(1)/10;
-		}
+		else
+			target_clock = adjusted_mode->clock;
+
+		/* FDI is a binary signal running at ~2.7GHz, encoding
+		 * each output octet as 10 bits. The actual frequency
+		 * is stored as a divider into a 100MHz clock, and the
+		 * mode pixel clock is stored in units of 1KHz.
+		 * Hence the bw of each lane in terms of the mode signal
+		 * is:
+		 */
+		link_bw = intel_fdi_link_freq(dev) * MHz(100)/KHz(1)/10;
+	}
 
-		/* determine panel color depth */
-		temp = I915_READ(PIPECONF(pipe));
-		temp &= ~PIPE_BPC_MASK;
-		if (is_lvds) {
-			/* the BPC will be 6 if it is 18-bit LVDS panel */
-			if ((I915_READ(PCH_LVDS) & LVDS_A3_POWER_MASK) == LVDS_A3_POWER_UP)
-				temp |= PIPE_8BPC;
-			else
-				temp |= PIPE_6BPC;
-		} else if (has_edp_encoder) {
-			switch (dev_priv->edp.bpp/3) {
-			case 8:
-				temp |= PIPE_8BPC;
-				break;
-			case 10:
-				temp |= PIPE_10BPC;
-				break;
-			case 6:
-				temp |= PIPE_6BPC;
-				break;
-			case 12:
-				temp |= PIPE_12BPC;
-				break;
-			}
-		} else
+	/* determine panel color depth */
+	temp = I915_READ(PIPECONF(pipe));
+	temp &= ~PIPE_BPC_MASK;
+	if (is_lvds) {
+		/* the BPC will be 6 if it is 18-bit LVDS panel */
+		if ((I915_READ(PCH_LVDS) & LVDS_A3_POWER_MASK) == LVDS_A3_POWER_UP)
+			temp |= PIPE_8BPC;
+		else
+			temp |= PIPE_6BPC;
+	} else if (has_edp_encoder) {
+		switch (dev_priv->edp.bpp/3) {
+		case 8:
 			temp |= PIPE_8BPC;
-		I915_WRITE(PIPECONF(pipe), temp);
-
-		switch (temp & PIPE_BPC_MASK) {
-		case PIPE_8BPC:
-			bpp = 24;
 			break;
-		case PIPE_10BPC:
-			bpp = 30;
+		case 10:
+			temp |= PIPE_10BPC;
 			break;
-		case PIPE_6BPC:
-			bpp = 18;
+		case 6:
+			temp |= PIPE_6BPC;
 			break;
-		case PIPE_12BPC:
-			bpp = 36;
+		case 12:
+			temp |= PIPE_12BPC;
 			break;
-		default:
-			DRM_ERROR("unknown pipe bpc value\n");
-			bpp = 24;
-		}
-
-		if (!lane) {
-			/* 
-			 * Account for spread spectrum to avoid
-			 * oversubscribing the link. Max center spread
-			 * is 2.5%; use 5% for safety's sake.
-			 */
-			u32 bps = target_clock * bpp * 21 / 20;
-			lane = bps / (link_bw * 8) + 1;
 		}
+	} else
+		temp |= PIPE_8BPC;
+	I915_WRITE(PIPECONF(pipe), temp);
 
-		intel_crtc->fdi_lanes = lane;
+	switch (temp & PIPE_BPC_MASK) {
+	case PIPE_8BPC:
+		bpp = 24;
+		break;
+	case PIPE_10BPC:
+		bpp = 30;
+		break;
+	case PIPE_6BPC:
+		bpp = 18;
+		break;
+	case PIPE_12BPC:
+		bpp = 36;
+		break;
+	default:
+		DRM_ERROR("unknown pipe bpc value\n");
+		bpp = 24;
+	}
 
-		if (pixel_multiplier > 1)
-			link_bw *= pixel_multiplier;
-		ironlake_compute_m_n(bpp, lane, target_clock, link_bw, &m_n);
+	if (!lane) {
+		/*
+		 * Account for spread spectrum to avoid
+		 * oversubscribing the link. Max center spread
+		 * is 2.5%; use 5% for safety's sake.
+		 */
+		u32 bps = target_clock * bpp * 21 / 20;
+		lane = bps / (link_bw * 8) + 1;
 	}
 
+	intel_crtc->fdi_lanes = lane;
+
+	if (pixel_multiplier > 1)
+		link_bw *= pixel_multiplier;
+	ironlake_compute_m_n(bpp, lane, target_clock, link_bw, &m_n);
+
 	/* Ironlake: try to setup display ref clock before DPLL
 	 * enabling. This is only under driver's control after
 	 * PCH B stepping, previous chipset stepping should be
 	 * ignoring this setting.
 	 */
-	if (HAS_PCH_SPLIT(dev)) {
-		temp = I915_READ(PCH_DREF_CONTROL);
-		/* Always enable nonspread source */
-		temp &= ~DREF_NONSPREAD_SOURCE_MASK;
-		temp |= DREF_NONSPREAD_SOURCE_ENABLE;
-		temp &= ~DREF_SSC_SOURCE_MASK;
-		temp |= DREF_SSC_SOURCE_ENABLE;
-		I915_WRITE(PCH_DREF_CONTROL, temp);
-
-		POSTING_READ(PCH_DREF_CONTROL);
-		udelay(200);
-
-		if (has_edp_encoder) {
-			if (intel_panel_use_ssc(dev_priv)) {
-				temp |= DREF_SSC1_ENABLE;
-				I915_WRITE(PCH_DREF_CONTROL, temp);
-
-				POSTING_READ(PCH_DREF_CONTROL);
-				udelay(200);
-			}
-			temp &= ~DREF_CPU_SOURCE_OUTPUT_MASK;
+	temp = I915_READ(PCH_DREF_CONTROL);
+	/* Always enable nonspread source */
+	temp &= ~DREF_NONSPREAD_SOURCE_MASK;
+	temp |= DREF_NONSPREAD_SOURCE_ENABLE;
+	temp &= ~DREF_SSC_SOURCE_MASK;
+	temp |= DREF_SSC_SOURCE_ENABLE;
+	I915_WRITE(PCH_DREF_CONTROL, temp);
+
+	POSTING_READ(PCH_DREF_CONTROL);
+	udelay(200);
 
-			/* Enable CPU source on CPU attached eDP */
-			if (!intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
-				if (intel_panel_use_ssc(dev_priv))
-					temp |= DREF_CPU_SOURCE_OUTPUT_DOWNSPREAD;
-				else
-					temp |= DREF_CPU_SOURCE_OUTPUT_NONSPREAD;
-			} else {
-				/* Enable SSC on PCH eDP if needed */
-				if (intel_panel_use_ssc(dev_priv)) {
-					DRM_ERROR("enabling SSC on PCH\n");
-					temp |= DREF_SUPERSPREAD_SOURCE_ENABLE;
-				}
-			}
+	if (has_edp_encoder) {
+		if (intel_panel_use_ssc(dev_priv)) {
+			temp |= DREF_SSC1_ENABLE;
 			I915_WRITE(PCH_DREF_CONTROL, temp);
+
 			POSTING_READ(PCH_DREF_CONTROL);
 			udelay(200);
 		}
+		temp &= ~DREF_CPU_SOURCE_OUTPUT_MASK;
+
+		/* Enable CPU source on CPU attached eDP */
+		if (!intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
+			if (intel_panel_use_ssc(dev_priv))
+				temp |= DREF_CPU_SOURCE_OUTPUT_DOWNSPREAD;
+			else
+				temp |= DREF_CPU_SOURCE_OUTPUT_NONSPREAD;
+		} else {
+			/* Enable SSC on PCH eDP if needed */
+			if (intel_panel_use_ssc(dev_priv)) {
+				DRM_ERROR("enabling SSC on PCH\n");
+				temp |= DREF_SUPERSPREAD_SOURCE_ENABLE;
+			}
+		}
+		I915_WRITE(PCH_DREF_CONTROL, temp);
+		POSTING_READ(PCH_DREF_CONTROL);
+		udelay(200);
 	}
 
 	if (IS_PINEVIEW(dev)) {
@@ -5183,24 +5180,19 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 	}
 
 	/* Enable autotuning of the PLL clock (if permissible) */
-	if (HAS_PCH_SPLIT(dev)) {
-		int factor = 21;
-
-		if (is_lvds) {
-			if ((intel_panel_use_ssc(dev_priv) &&
-			     dev_priv->lvds_ssc_freq == 100) ||
-			    (I915_READ(PCH_LVDS) & LVDS_CLKB_POWER_MASK) == LVDS_CLKB_POWER_UP)
-				factor = 25;
-		} else if (is_sdvo && is_tv)
-			factor = 20;
+	factor = 21;
+	if (is_lvds) {
+		if ((intel_panel_use_ssc(dev_priv) &&
+		     dev_priv->lvds_ssc_freq == 100) ||
+		    (I915_READ(PCH_LVDS) & LVDS_CLKB_POWER_MASK) == LVDS_CLKB_POWER_UP)
+			factor = 25;
+	} else if (is_sdvo && is_tv)
+		factor = 20;
 
-		if (clock.m1 < factor * clock.n)
-			fp |= FP_CB_TUNE;
-	}
+	if (clock.m1 < factor * clock.n)
+		fp |= FP_CB_TUNE;
 
 	dpll = 0;
-	if (!HAS_PCH_SPLIT(dev))
-		dpll = DPLL_VGA_MODE_DIS;
 
 	if (!IS_GEN2(dev)) {
 		if (is_lvds)
@@ -5212,7 +5204,7 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 			if (pixel_multiplier > 1) {
 				if (IS_I945G(dev) || IS_I945GM(dev) || IS_G33(dev))
 					dpll |= (pixel_multiplier - 1) << SDVO_MULTIPLIER_SHIFT_HIRES;
-				else if (HAS_PCH_SPLIT(dev))
+				else
 					dpll |= (pixel_multiplier - 1) << PLL_REF_SDVO_HDMI_MULTIPLIER_SHIFT;
 			}
 			dpll |= DPLL_DVO_HIGH_SPEED;
@@ -5226,8 +5218,7 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 		else {
 			dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT;
 			/* also FPA1 */
-			if (HAS_PCH_SPLIT(dev))
-				dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA1_P1_POST_DIV_SHIFT;
+			dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA1_P1_POST_DIV_SHIFT;
 			if (IS_G4X(dev) && has_reduced_clock)
 				dpll |= (1 << (reduced_clock.p1 - 1)) << DPLL_FPA1_P1_POST_DIV_SHIFT;
 		}
@@ -5245,8 +5236,6 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 			dpll |= DPLLB_LVDS_P2_CLOCK_DIV_14;
 			break;
 		}
-		if (INTEL_INFO(dev)->gen >= 4 && !HAS_PCH_SPLIT(dev))
-			dpll |= (6 << PLL_LOAD_PULSE_PHASE_SHIFT);
 	} else {
 		if (is_lvds) {
 			dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT;
@@ -5277,15 +5266,6 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 	/* Set up the display plane register */
 	dspcntr = DISPPLANE_GAMMA_ENABLE;
 
-	/* Ironlake's plane is forced to pipe, bit 24 is to
-	   enable color space conversion */
-	if (!HAS_PCH_SPLIT(dev)) {
-		if (pipe == 0)
-			dspcntr &= ~DISPPLANE_SEL_PIPE_MASK;
-		else
-			dspcntr |= DISPPLANE_SEL_PIPE_B;
-	}
-
 	if (pipe == 0 && INTEL_INFO(dev)->gen < 4) {
 		/* Enable pixel doubling when the dot clock is > 90% of the (display)
 		 * core speed.
@@ -5300,20 +5280,12 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 			pipeconf &= ~PIPECONF_DOUBLE_WIDE;
 	}
 
-	if (!HAS_PCH_SPLIT(dev))
-		dpll |= DPLL_VCO_ENABLE;
-
 	DRM_DEBUG_KMS("Mode for pipe %c:\n", pipe == 0 ? 'A' : 'B');
 	drm_mode_debug_printmodeline(mode);
 
 	/* assign to Ironlake registers */
-	if (HAS_PCH_SPLIT(dev)) {
-		fp_reg = PCH_FP0(pipe);
-		dpll_reg = PCH_DPLL(pipe);
-	} else {
-		fp_reg = FP0(pipe);
-		dpll_reg = DPLL(pipe);
-	}
+	fp_reg = PCH_FP0(pipe);
+	dpll_reg = PCH_DPLL(pipe);
 
 	/* PCH eDP needs FDI, but CPU eDP does not */
 	if (!has_edp_encoder || intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
@@ -5352,9 +5324,7 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 	 * things on.
 	 */
 	if (is_lvds) {
-		reg = LVDS;
-		if (HAS_PCH_SPLIT(dev))
-			reg = PCH_LVDS;
+		reg = PCH_LVDS;
 
 		temp = I915_READ(reg);
 		temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
@@ -5383,13 +5353,6 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 		 * appropriately here, but we need to look more thoroughly into how
 		 * panels behave in the two modes.
 		 */
-		/* set the dithering flag on non-PCH LVDS as needed */
-		if (INTEL_INFO(dev)->gen >= 4 && !HAS_PCH_SPLIT(dev)) {
-			if (dev_priv->lvds_dither)
-				temp |= LVDS_ENABLE_DITHER;
-			else
-				temp &= ~LVDS_ENABLE_DITHER;
-		}
 		if (adjusted_mode->flags & DRM_MODE_FLAG_NHSYNC)
 			lvds_sync |= LVDS_HSYNC_POLARITY;
 		if (adjusted_mode->flags & DRM_MODE_FLAG_NVSYNC)
@@ -5410,18 +5373,16 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 	}
 
 	/* set the dithering flag and clear for anything other than a panel. */
-	if (HAS_PCH_SPLIT(dev)) {
-		pipeconf &= ~PIPECONF_DITHER_EN;
-		pipeconf &= ~PIPECONF_DITHER_TYPE_MASK;
-		if (dev_priv->lvds_dither && (is_lvds || has_edp_encoder)) {
-			pipeconf |= PIPECONF_DITHER_EN;
-			pipeconf |= PIPECONF_DITHER_TYPE_ST1;
-		}
+	pipeconf &= ~PIPECONF_DITHER_EN;
+	pipeconf &= ~PIPECONF_DITHER_TYPE_MASK;
+	if (dev_priv->lvds_dither && (is_lvds || has_edp_encoder)) {
+		pipeconf |= PIPECONF_DITHER_EN;
+		pipeconf |= PIPECONF_DITHER_TYPE_ST1;
 	}
 
 	if (is_dp || intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
 		intel_dp_set_m_n(crtc, mode, adjusted_mode);
-	} else if (HAS_PCH_SPLIT(dev)) {
+	} else {
 		/* For non-DP output, clear any trans DP clock recovery setting.*/
 		I915_WRITE(TRANSDATA_M1(pipe), 0);
 		I915_WRITE(TRANSDATA_N1(pipe), 0);
@@ -5429,31 +5390,20 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 		I915_WRITE(TRANSDPLINK_N1(pipe), 0);
 	}
 
-	if (!has_edp_encoder || intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
+	if (!has_edp_encoder ||
+	    intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
 		I915_WRITE(dpll_reg, dpll);
 
 		/* Wait for the clocks to stabilize. */
 		POSTING_READ(dpll_reg);
 		udelay(150);
 
-		if (INTEL_INFO(dev)->gen >= 4 && !HAS_PCH_SPLIT(dev)) {
-			temp = 0;
-			if (is_sdvo) {
-				temp = intel_mode_get_pixel_multiplier(adjusted_mode);
-				if (temp > 1)
-					temp = (temp - 1) << DPLL_MD_UDI_MULTIPLIER_SHIFT;
-				else
-					temp = 0;
-			}
-			I915_WRITE(DPLL_MD(pipe), temp);
-		} else {
-			/* The pixel multiplier can only be updated once the
-			 * DPLL is enabled and the clocks are stable.
-			 *
-			 * So write it again.
-			 */
-			I915_WRITE(dpll_reg, dpll);
-		}
+		/* The pixel multiplier can only be updated once the
+		 * DPLL is enabled and the clocks are stable.
+		 *
+		 * So write it again.
+		 */
+		I915_WRITE(dpll_reg, dpll);
 	}
 
 	intel_crtc->lowfreq_avail = false;
@@ -5504,33 +5454,24 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 		   (adjusted_mode->crtc_vsync_start - 1) |
 		   ((adjusted_mode->crtc_vsync_end - 1) << 16));
 
-	/* pipesrc and dspsize control the size that is scaled from,
-	 * which should always be the user's requested size.
+	/* pipesrc controls the size that is scaled from, which should
+	 * always be the user's requested size.
 	 */
-	if (!HAS_PCH_SPLIT(dev)) {
-		I915_WRITE(DSPSIZE(plane),
-			   ((mode->vdisplay - 1) << 16) |
-			   (mode->hdisplay - 1));
-		I915_WRITE(DSPPOS(plane), 0);
-	}
 	I915_WRITE(PIPESRC(pipe),
 		   ((mode->hdisplay - 1) << 16) | (mode->vdisplay - 1));
 
-	if (HAS_PCH_SPLIT(dev)) {
-		I915_WRITE(PIPE_DATA_M1(pipe), TU_SIZE(m_n.tu) | m_n.gmch_m);
-		I915_WRITE(PIPE_DATA_N1(pipe), m_n.gmch_n);
-		I915_WRITE(PIPE_LINK_M1(pipe), m_n.link_m);
-		I915_WRITE(PIPE_LINK_N1(pipe), m_n.link_n);
+	I915_WRITE(PIPE_DATA_M1(pipe), TU_SIZE(m_n.tu) | m_n.gmch_m);
+	I915_WRITE(PIPE_DATA_N1(pipe), m_n.gmch_n);
+	I915_WRITE(PIPE_LINK_M1(pipe), m_n.link_m);
+	I915_WRITE(PIPE_LINK_N1(pipe), m_n.link_n);
 
-		if (has_edp_encoder && !intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
-			ironlake_set_pll_edp(crtc, adjusted_mode->clock);
-		}
+	if (has_edp_encoder &&
+	    !intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
+		ironlake_set_pll_edp(crtc, adjusted_mode->clock);
 	}
 
 	I915_WRITE(PIPECONF(pipe), pipeconf);
 	POSTING_READ(PIPECONF(pipe));
-	if (!HAS_PCH_SPLIT(dev))
-		intel_enable_pipe(dev_priv, pipe, false);
 
 	intel_wait_for_vblank(dev, pipe);
 
@@ -5542,8 +5483,6 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 
 	I915_WRITE(DSPCNTR(plane), dspcntr);
 	POSTING_READ(DSPCNTR(plane));
-	if (!HAS_PCH_SPLIT(dev))
-		intel_enable_plane(dev_priv, plane, pipe);
 
 	ret = intel_pipe_set_base(crtc, x, y, old_fb);
 
Signature · 1 line
1.7.4.1
#12 lore raw

Re: [PATCH 6/9] drm/i915: Drop non-HAS_PCH_SPLIT() code from ironlake_crtc_mode_set().

Quoted 1 line · Eric Anholt

Ironlake is where the PCH split started.

Jesse, what's your objection here? IOW, where's your reviewed-by ;-) -Chris

Signature · 1 line
Chris Wilson, Intel Open Source Technology Centre
Reviewed-by on v1 6/9
#13 lore raw

Re: [PATCH 6/9] drm/i915: Drop non-HAS_PCH_SPLIT() code from ironlake_crtc_mode_set().

In reply to Eric Anholt
Quoted 7 lines · On Wed, 30 Mar 2011 13:01:07 -0700 Eric Anholt <[email protected]> wrote:

Ironlake is where the PCH split started.

---
 drivers/gpu/drm/i915/intel_display.c |  361 ++++++++++++++--------------------
 1 files changed, 150 insertions(+), 211 deletions(-)
Signature · 1 line
Jesse Barnes, Intel Open Source Technology Center
#14 lore raw

PATCH 7/9 drm/i915: Drop remaining pre-Ironlake code from ironlake_crtc_mode_set().

In reply to Eric Anholt
---
 drivers/gpu/drm/i915/intel_display.c |  119 ++++++++++-----------------------
 1 files changed, 36 insertions(+), 83 deletions(-)
drivers/gpu/drm/i915/intel_display.c +36 -83
index 496bee9..41d82b5 100644
@@ -4922,7 +4922,7 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 	int refclk, num_connectors = 0;
 	intel_clock_t clock, reduced_clock;
 	u32 dpll, fp = 0, fp2 = 0, dspcntr, pipeconf;
-	bool ok, has_reduced_clock = false, is_sdvo = false, is_dvo = false;
+	bool ok, has_reduced_clock = false, is_sdvo = false;
 	bool is_crt = false, is_lvds = false, is_tv = false, is_dp = false;
 	struct intel_encoder *has_edp_encoder = NULL;
 	struct drm_mode_config *mode_config = &dev->mode_config;
@@ -4948,9 +4948,6 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 			if (encoder->needs_tv_clock)
 				is_tv = true;
 			break;
-		case INTEL_OUTPUT_DVO:
-			is_dvo = true;
-			break;
 		case INTEL_OUTPUT_TVOUT:
 			is_tv = true;
 			break;
@@ -4972,13 +4969,11 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 		refclk = dev_priv->lvds_ssc_freq * 1000;
 		DRM_DEBUG_KMS("using SSC reference clock of %d MHz\n",
 			      refclk / 1000);
-	} else if (!IS_GEN2(dev)) {
+	} else {
 		refclk = 96000;
 		if (!has_edp_encoder ||
 		    intel_encoder_is_pch_edp(&has_edp_encoder->base))
 			refclk = 120000; /* 120Mhz refclk */
-	} else {
-		refclk = 48000;
 	}
 
 	/*
@@ -5167,17 +5162,10 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 		udelay(200);
 	}
 
-	if (IS_PINEVIEW(dev)) {
-		fp = (1 << clock.n) << 16 | clock.m1 << 8 | clock.m2;
-		if (has_reduced_clock)
-			fp2 = (1 << reduced_clock.n) << 16 |
-				reduced_clock.m1 << 8 | reduced_clock.m2;
-	} else {
-		fp = clock.n << 16 | clock.m1 << 8 | clock.m2;
-		if (has_reduced_clock)
-			fp2 = reduced_clock.n << 16 | reduced_clock.m1 << 8 |
-				reduced_clock.m2;
-	}
+	fp = clock.n << 16 | clock.m1 << 8 | clock.m2;
+	if (has_reduced_clock)
+		fp2 = reduced_clock.n << 16 | reduced_clock.m1 << 8 |
+			reduced_clock.m2;
 
 	/* Enable autotuning of the PLL clock (if permissible) */
 	factor = 21;
@@ -5194,59 +5182,38 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 
 	dpll = 0;
 
-	if (!IS_GEN2(dev)) {
-		if (is_lvds)
-			dpll |= DPLLB_MODE_LVDS;
-		else
-			dpll |= DPLLB_MODE_DAC_SERIAL;
-		if (is_sdvo) {
-			int pixel_multiplier = intel_mode_get_pixel_multiplier(adjusted_mode);
-			if (pixel_multiplier > 1) {
-				if (IS_I945G(dev) || IS_I945GM(dev) || IS_G33(dev))
-					dpll |= (pixel_multiplier - 1) << SDVO_MULTIPLIER_SHIFT_HIRES;
-				else
-					dpll |= (pixel_multiplier - 1) << PLL_REF_SDVO_HDMI_MULTIPLIER_SHIFT;
-			}
-			dpll |= DPLL_DVO_HIGH_SPEED;
+	if (is_lvds)
+		dpll |= DPLLB_MODE_LVDS;
+	else
+		dpll |= DPLLB_MODE_DAC_SERIAL;
+	if (is_sdvo) {
+		int pixel_multiplier = intel_mode_get_pixel_multiplier(adjusted_mode);
+		if (pixel_multiplier > 1) {
+			dpll |= (pixel_multiplier - 1) << PLL_REF_SDVO_HDMI_MULTIPLIER_SHIFT;
 		}
-		if (is_dp || intel_encoder_is_pch_edp(&has_edp_encoder->base))
-			dpll |= DPLL_DVO_HIGH_SPEED;
+		dpll |= DPLL_DVO_HIGH_SPEED;
+	}
+	if (is_dp || intel_encoder_is_pch_edp(&has_edp_encoder->base))
+		dpll |= DPLL_DVO_HIGH_SPEED;
 
-		/* compute bitmask from p1 value */
-		if (IS_PINEVIEW(dev))
-			dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT_PINEVIEW;
-		else {
-			dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT;
-			/* also FPA1 */
-			dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA1_P1_POST_DIV_SHIFT;
-			if (IS_G4X(dev) && has_reduced_clock)
-				dpll |= (1 << (reduced_clock.p1 - 1)) << DPLL_FPA1_P1_POST_DIV_SHIFT;
-		}
-		switch (clock.p2) {
-		case 5:
-			dpll |= DPLL_DAC_SERIAL_P2_CLOCK_DIV_5;
-			break;
-		case 7:
-			dpll |= DPLLB_LVDS_P2_CLOCK_DIV_7;
-			break;
-		case 10:
-			dpll |= DPLL_DAC_SERIAL_P2_CLOCK_DIV_10;
-			break;
-		case 14:
-			dpll |= DPLLB_LVDS_P2_CLOCK_DIV_14;
-			break;
-		}
-	} else {
-		if (is_lvds) {
-			dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT;
-		} else {
-			if (clock.p1 == 2)
-				dpll |= PLL_P1_DIVIDE_BY_TWO;
-			else
-				dpll |= (clock.p1 - 2) << DPLL_FPA01_P1_POST_DIV_SHIFT;
-			if (clock.p2 == 4)
-				dpll |= PLL_P2_DIVIDE_BY_4;
-		}
+	/* compute bitmask from p1 value */
+	dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA01_P1_POST_DIV_SHIFT;
+	/* also FPA1 */
+	dpll |= (1 << (clock.p1 - 1)) << DPLL_FPA1_P1_POST_DIV_SHIFT;
+
+	switch (clock.p2) {
+	case 5:
+		dpll |= DPLL_DAC_SERIAL_P2_CLOCK_DIV_5;
+		break;
+	case 7:
+		dpll |= DPLLB_LVDS_P2_CLOCK_DIV_7;
+		break;
+	case 10:
+		dpll |= DPLL_DAC_SERIAL_P2_CLOCK_DIV_10;
+		break;
+	case 14:
+		dpll |= DPLLB_LVDS_P2_CLOCK_DIV_14;
+		break;
 	}
 
 	if (is_sdvo && is_tv)
@@ -5266,20 +5233,6 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 	/* Set up the display plane register */
 	dspcntr = DISPPLANE_GAMMA_ENABLE;
 
-	if (pipe == 0 && INTEL_INFO(dev)->gen < 4) {
-		/* Enable pixel doubling when the dot clock is > 90% of the (display)
-		 * core speed.
-		 *
-		 * XXX: No double-wide on 915GM pipe B. Is that the only reason for the
-		 * pipe == 0 check?
-		 */
-		if (mode->clock >
-		    dev_priv->display.get_display_clock_speed(dev) * 9 / 10)
-			pipeconf |= PIPECONF_DOUBLE_WIDE;
-		else
-			pipeconf &= ~PIPECONF_DOUBLE_WIDE;
-	}
-
 	DRM_DEBUG_KMS("Mode for pipe %c:\n", pipe == 0 ? 'A' : 'B');
 	drm_mode_debug_printmodeline(mode);
 
Signature · 1 line
1.7.4.1
Reviewed-by on v1 7/9
#15 lore raw

Re: [PATCH 7/9] drm/i915: Drop remaining pre-Ironlake code from ironlake_crtc_mode_set().

Quoted 4 lines · On Wed, 30 Mar 2011 13:01:08 -0700 Eric Anholt <[email protected]> wrote:
---
 drivers/gpu/drm/i915/intel_display.c |  119 ++++++++++-----------------------
 1 files changed, 36 insertions(+), 83 deletions(-)
Signature · 1 line
Jesse Barnes, Intel Open Source Technology Center
#16 lore raw

PATCH 8/9 drm/i915: Clean up leftover DPLL and LVDS register choice from pch split.

In reply to Eric Anholt

We used to have these from the product of (pch, non-pch) * (pipe a, pipe b). Now we can just use the nice per-pipe reg macros in the split out crtc_mode_sets.

---
 drivers/gpu/drm/i915/intel_display.c |   57 +++++++++++++---------------------
 1 files changed, 22 insertions(+), 35 deletions(-)
drivers/gpu/drm/i915/intel_display.c +22 -35
index 41d82b5..8de3473 100644
@@ -4524,7 +4524,6 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 	struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
 	int pipe = intel_crtc->pipe;
 	int plane = intel_crtc->plane;
-	u32 fp_reg, dpll_reg;
 	int refclk, num_connectors = 0;
 	intel_clock_t clock, reduced_clock;
 	u32 dpll, fp = 0, fp2 = 0, dspcntr, pipeconf;
@@ -4534,7 +4533,7 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 	struct intel_encoder *encoder;
 	const intel_limit_t *limit;
 	int ret;
-	u32 reg, temp;
+	u32 temp;
 	u32 lvds_sync = 0;
 
 	list_for_each_entry(encoder, &mode_config->encoder_list, base.head) {
@@ -4740,13 +4739,10 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 	DRM_DEBUG_KMS("Mode for pipe %c:\n", pipe == 0 ? 'A' : 'B');
 	drm_mode_debug_printmodeline(mode);
 
-	fp_reg = FP0(pipe);
-	dpll_reg = DPLL(pipe);
+	I915_WRITE(FP0(pipe), fp);
+	I915_WRITE(DPLL(pipe), dpll & ~DPLL_VCO_ENABLE);
 
-	I915_WRITE(fp_reg, fp);
-	I915_WRITE(dpll_reg, dpll & ~DPLL_VCO_ENABLE);
-
-	POSTING_READ(dpll_reg);
+	POSTING_READ(DPLL(pipe));
 	udelay(150);
 
 	/* The LVDS pin pair needs to be on before the DPLLs are enabled.
@@ -4754,9 +4750,7 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 	 * things on.
 	 */
 	if (is_lvds) {
-		reg = LVDS;
-
-		temp = I915_READ(reg);
+		temp = I915_READ(LVDS);
 		temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
 		if (pipe == 1) {
 			temp |= LVDS_PIPEB_SELECT;
@@ -4800,17 +4794,17 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 			temp &= ~(LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY);
 			temp |= lvds_sync;
 		}
-		I915_WRITE(reg, temp);
+		I915_WRITE(LVDS, temp);
 	}
 
 	if (is_dp) {
 		intel_dp_set_m_n(crtc, mode, adjusted_mode);
 	}
 
-	I915_WRITE(dpll_reg, dpll);
+	I915_WRITE(DPLL(pipe), dpll);
 
 	/* Wait for the clocks to stabilize. */
-	POSTING_READ(dpll_reg);
+	POSTING_READ(DPLL(pipe));
 	udelay(150);
 
 	if (INTEL_INFO(dev)->gen >= 4) {
@@ -4829,19 +4823,19 @@ static int i9xx_crtc_mode_set(struct drm_crtc *crtc,
 		 *
 		 * So write it again.
 		 */
-		I915_WRITE(dpll_reg, dpll);
+		I915_WRITE(DPLL(pipe), dpll);
 	}
 
 	intel_crtc->lowfreq_avail = false;
 	if (is_lvds && has_reduced_clock && i915_powersave) {
-		I915_WRITE(fp_reg + 4, fp2);
+		I915_WRITE(FP1(pipe), fp2);
 		intel_crtc->lowfreq_avail = true;
 		if (HAS_PIPE_CXSR(dev)) {
 			DRM_DEBUG_KMS("enabling CxSR downclocking\n");
 			pipeconf |= PIPECONF_CXSR_DOWNCLOCK;
 		}
 	} else {
-		I915_WRITE(fp_reg + 4, fp);
+		I915_WRITE(FP1(pipe), fp);
 		if (HAS_PIPE_CXSR(dev)) {
 			DRM_DEBUG_KMS("disabling CxSR downclocking\n");
 			pipeconf &= ~PIPECONF_CXSR_DOWNCLOCK;
@@ -4918,7 +4912,6 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 	struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
 	int pipe = intel_crtc->pipe;
 	int plane = intel_crtc->plane;
-	u32 fp_reg, dpll_reg;
 	int refclk, num_connectors = 0;
 	intel_clock_t clock, reduced_clock;
 	u32 dpll, fp = 0, fp2 = 0, dspcntr, pipeconf;
@@ -4930,7 +4923,7 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 	const intel_limit_t *limit;
 	int ret;
 	struct fdi_m_n m_n = {0};
-	u32 reg, temp;
+	u32 temp;
 	u32 lvds_sync = 0;
 	int target_clock, pixel_multiplier, lane, link_bw, bpp, factor;
 
@@ -5236,16 +5229,12 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 	DRM_DEBUG_KMS("Mode for pipe %c:\n", pipe == 0 ? 'A' : 'B');
 	drm_mode_debug_printmodeline(mode);
 
-	/* assign to Ironlake registers */
-	fp_reg = PCH_FP0(pipe);
-	dpll_reg = PCH_DPLL(pipe);
-
 	/* PCH eDP needs FDI, but CPU eDP does not */
 	if (!has_edp_encoder || intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
-		I915_WRITE(fp_reg, fp);
-		I915_WRITE(dpll_reg, dpll & ~DPLL_VCO_ENABLE);
+		I915_WRITE(PCH_FP0(pipe), fp);
+		I915_WRITE(PCH_DPLL(pipe), dpll & ~DPLL_VCO_ENABLE);
 
-		POSTING_READ(dpll_reg);
+		POSTING_READ(PCH_DPLL(pipe));
 		udelay(150);
 	}
 
@@ -5277,9 +5266,7 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 	 * things on.
 	 */
 	if (is_lvds) {
-		reg = PCH_LVDS;
-
-		temp = I915_READ(reg);
+		temp = I915_READ(PCH_LVDS);
 		temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
 		if (pipe == 1) {
 			if (HAS_PCH_CPT(dev))
@@ -5322,7 +5309,7 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 			temp &= ~(LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY);
 			temp |= lvds_sync;
 		}
-		I915_WRITE(reg, temp);
+		I915_WRITE(PCH_LVDS, temp);
 	}
 
 	/* set the dithering flag and clear for anything other than a panel. */
@@ -5345,10 +5332,10 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 
 	if (!has_edp_encoder ||
 	    intel_encoder_is_pch_edp(&has_edp_encoder->base)) {
-		I915_WRITE(dpll_reg, dpll);
+		I915_WRITE(PCH_DPLL(pipe), dpll);
 
 		/* Wait for the clocks to stabilize. */
-		POSTING_READ(dpll_reg);
+		POSTING_READ(PCH_DPLL(pipe));
 		udelay(150);
 
 		/* The pixel multiplier can only be updated once the
@@ -5356,19 +5343,19 @@ static int ironlake_crtc_mode_set(struct drm_crtc *crtc,
 		 *
 		 * So write it again.
 		 */
-		I915_WRITE(dpll_reg, dpll);
+		I915_WRITE(PCH_DPLL(pipe), dpll);
 	}
 
 	intel_crtc->lowfreq_avail = false;
 	if (is_lvds && has_reduced_clock && i915_powersave) {
-		I915_WRITE(fp_reg + 4, fp2);
+		I915_WRITE(PCH_FP1(pipe), fp2);
 		intel_crtc->lowfreq_avail = true;
 		if (HAS_PIPE_CXSR(dev)) {
 			DRM_DEBUG_KMS("enabling CxSR downclocking\n");
 			pipeconf |= PIPECONF_CXSR_DOWNCLOCK;
 		}
 	} else {
-		I915_WRITE(fp_reg + 4, fp);
+		I915_WRITE(PCH_FP1(pipe), fp);
 		if (HAS_PIPE_CXSR(dev)) {
 			DRM_DEBUG_KMS("disabling CxSR downclocking\n");
 			pipeconf &= ~PIPECONF_CXSR_DOWNCLOCK;
Signature · 1 line
1.7.4.1
Reviewed-by on v1 8/9
#17 lore raw

Re: [PATCH 8/9] drm/i915: Clean up leftover DPLL and LVDS register choice from pch split.

Quoted 6 lines · On Wed, 30 Mar 2011 13:01:09 -0700 Eric Anholt <[email protected]> wrote:

We used to have these from the product of (pch, non-pch) * (pipe a, pipe b). Now we can just use the nice per-pipe reg macros in the split out crtc_mode_sets.

---

Signature · 1 line
Jesse Barnes, Intel Open Source Technology Center
#18 lore raw

PATCH 9/9 drm/i915: Fold the DPLL limit defines into the structs that use them.

In reply to Eric Anholt

They're used in one place, and not providing any descriptive value, with their names just being approximately the conjunction of the struct name and the struct field.

This diff was produced with gcc -E, copying the new struct definitions out, moving a couple of the old comments into place in the new structs, and reindenting.

---
 drivers/gpu/drm/i915/intel_display.c |  650 ++++++++++------------------------
 1 files changed, 181 insertions(+), 469 deletions(-)
drivers/gpu/drm/i915/intel_display.c +181 -469
index 8de3473..1ff9fe3 100644
@@ -76,255 +76,6 @@ struct intel_limit {
 		      int, int, intel_clock_t *);
 };
 
-#define I8XX_DOT_MIN		  25000
-#define I8XX_DOT_MAX		 350000
-#define I8XX_VCO_MIN		 930000
-#define I8XX_VCO_MAX		1400000
-#define I8XX_N_MIN		      3
-#define I8XX_N_MAX		     16
-#define I8XX_M_MIN		     96
-#define I8XX_M_MAX		    140
-#define I8XX_M1_MIN		     18
-#define I8XX_M1_MAX		     26
-#define I8XX_M2_MIN		      6
-#define I8XX_M2_MAX		     16
-#define I8XX_P_MIN		      4
-#define I8XX_P_MAX		    128
-#define I8XX_P1_MIN		      2
-#define I8XX_P1_MAX		     33
-#define I8XX_P1_LVDS_MIN	      1
-#define I8XX_P1_LVDS_MAX	      6
-#define I8XX_P2_SLOW		      4
-#define I8XX_P2_FAST		      2
-#define I8XX_P2_LVDS_SLOW	      14
-#define I8XX_P2_LVDS_FAST	      7
-#define I8XX_P2_SLOW_LIMIT	 165000
-
-#define I9XX_DOT_MIN		  20000
-#define I9XX_DOT_MAX		 400000
-#define I9XX_VCO_MIN		1400000
-#define I9XX_VCO_MAX		2800000
-#define PINEVIEW_VCO_MIN		1700000
-#define PINEVIEW_VCO_MAX		3500000
-#define I9XX_N_MIN		      1
-#define I9XX_N_MAX		      6
-/* Pineview's Ncounter is a ring counter */
-#define PINEVIEW_N_MIN		      3
-#define PINEVIEW_N_MAX		      6
-#define I9XX_M_MIN		     70
-#define I9XX_M_MAX		    120
-#define PINEVIEW_M_MIN		      2
-#define PINEVIEW_M_MAX		    256
-#define I9XX_M1_MIN		     10
-#define I9XX_M1_MAX		     22
-#define I9XX_M2_MIN		      5
-#define I9XX_M2_MAX		      9
-/* Pineview M1 is reserved, and must be 0 */
-#define PINEVIEW_M1_MIN		      0
-#define PINEVIEW_M1_MAX		      0
-#define PINEVIEW_M2_MIN		      0
-#define PINEVIEW_M2_MAX		      254
-#define I9XX_P_SDVO_DAC_MIN	      5
-#define I9XX_P_SDVO_DAC_MAX	     80
-#define I9XX_P_LVDS_MIN		      7
-#define I9XX_P_LVDS_MAX		     98
-#define PINEVIEW_P_LVDS_MIN		      7
-#define PINEVIEW_P_LVDS_MAX		     112
-#define I9XX_P1_MIN		      1
-#define I9XX_P1_MAX		      8
-#define I9XX_P2_SDVO_DAC_SLOW		     10
-#define I9XX_P2_SDVO_DAC_FAST		      5
-#define I9XX_P2_SDVO_DAC_SLOW_LIMIT	 200000
-#define I9XX_P2_LVDS_SLOW		     14
-#define I9XX_P2_LVDS_FAST		      7
-#define I9XX_P2_LVDS_SLOW_LIMIT		 112000
-
-/*The parameter is for SDVO on G4x platform*/
-#define G4X_DOT_SDVO_MIN           25000
-#define G4X_DOT_SDVO_MAX           270000
-#define G4X_VCO_MIN                1750000
-#define G4X_VCO_MAX                3500000
-#define G4X_N_SDVO_MIN             1
-#define G4X_N_SDVO_MAX             4
-#define G4X_M_SDVO_MIN             104
-#define G4X_M_SDVO_MAX             138
-#define G4X_M1_SDVO_MIN            17
-#define G4X_M1_SDVO_MAX            23
-#define G4X_M2_SDVO_MIN            5
-#define G4X_M2_SDVO_MAX            11
-#define G4X_P_SDVO_MIN             10
-#define G4X_P_SDVO_MAX             30
-#define G4X_P1_SDVO_MIN            1
-#define G4X_P1_SDVO_MAX            3
-#define G4X_P2_SDVO_SLOW           10
-#define G4X_P2_SDVO_FAST           10
-#define G4X_P2_SDVO_LIMIT          270000
-
-/*The parameter is for HDMI_DAC on G4x platform*/
-#define G4X_DOT_HDMI_DAC_MIN           22000
-#define G4X_DOT_HDMI_DAC_MAX           400000
-#define G4X_N_HDMI_DAC_MIN             1
-#define G4X_N_HDMI_DAC_MAX             4
-#define G4X_M_HDMI_DAC_MIN             104
-#define G4X_M_HDMI_DAC_MAX             138
-#define G4X_M1_HDMI_DAC_MIN            16
-#define G4X_M1_HDMI_DAC_MAX            23
-#define G4X_M2_HDMI_DAC_MIN            5
-#define G4X_M2_HDMI_DAC_MAX            11
-#define G4X_P_HDMI_DAC_MIN             5
-#define G4X_P_HDMI_DAC_MAX             80
-#define G4X_P1_HDMI_DAC_MIN            1
-#define G4X_P1_HDMI_DAC_MAX            8
-#define G4X_P2_HDMI_DAC_SLOW           10
-#define G4X_P2_HDMI_DAC_FAST           5
-#define G4X_P2_HDMI_DAC_LIMIT          165000
-
-/*The parameter is for SINGLE_CHANNEL_LVDS on G4x platform*/
-#define G4X_DOT_SINGLE_CHANNEL_LVDS_MIN           20000
-#define G4X_DOT_SINGLE_CHANNEL_LVDS_MAX           115000
-#define G4X_N_SINGLE_CHANNEL_LVDS_MIN             1
-#define G4X_N_SINGLE_CHANNEL_LVDS_MAX             3
-#define G4X_M_SINGLE_CHANNEL_LVDS_MIN             104
-#define G4X_M_SINGLE_CHANNEL_LVDS_MAX             138
-#define G4X_M1_SINGLE_CHANNEL_LVDS_MIN            17
-#define G4X_M1_SINGLE_CHANNEL_LVDS_MAX            23
-#define G4X_M2_SINGLE_CHANNEL_LVDS_MIN            5
-#define G4X_M2_SINGLE_CHANNEL_LVDS_MAX            11
-#define G4X_P_SINGLE_CHANNEL_LVDS_MIN             28
-#define G4X_P_SINGLE_CHANNEL_LVDS_MAX             112
-#define G4X_P1_SINGLE_CHANNEL_LVDS_MIN            2
-#define G4X_P1_SINGLE_CHANNEL_LVDS_MAX            8
-#define G4X_P2_SINGLE_CHANNEL_LVDS_SLOW           14
-#define G4X_P2_SINGLE_CHANNEL_LVDS_FAST           14
-#define G4X_P2_SINGLE_CHANNEL_LVDS_LIMIT          0
-
-/*The parameter is for DUAL_CHANNEL_LVDS on G4x platform*/
-#define G4X_DOT_DUAL_CHANNEL_LVDS_MIN           80000
-#define G4X_DOT_DUAL_CHANNEL_LVDS_MAX           224000
-#define G4X_N_DUAL_CHANNEL_LVDS_MIN             1
-#define G4X_N_DUAL_CHANNEL_LVDS_MAX             3
-#define G4X_M_DUAL_CHANNEL_LVDS_MIN             104
-#define G4X_M_DUAL_CHANNEL_LVDS_MAX             138
-#define G4X_M1_DUAL_CHANNEL_LVDS_MIN            17
-#define G4X_M1_DUAL_CHANNEL_LVDS_MAX            23
-#define G4X_M2_DUAL_CHANNEL_LVDS_MIN            5
-#define G4X_M2_DUAL_CHANNEL_LVDS_MAX            11
-#define G4X_P_DUAL_CHANNEL_LVDS_MIN             14
-#define G4X_P_DUAL_CHANNEL_LVDS_MAX             42
-#define G4X_P1_DUAL_CHANNEL_LVDS_MIN            2
-#define G4X_P1_DUAL_CHANNEL_LVDS_MAX            6
-#define G4X_P2_DUAL_CHANNEL_LVDS_SLOW           7
-#define G4X_P2_DUAL_CHANNEL_LVDS_FAST           7
-#define G4X_P2_DUAL_CHANNEL_LVDS_LIMIT          0
-
-/*The parameter is for DISPLAY PORT on G4x platform*/
-#define G4X_DOT_DISPLAY_PORT_MIN           161670
-#define G4X_DOT_DISPLAY_PORT_MAX           227000
-#define G4X_N_DISPLAY_PORT_MIN             1
-#define G4X_N_DISPLAY_PORT_MAX             2
-#define G4X_M_DISPLAY_PORT_MIN             97
-#define G4X_M_DISPLAY_PORT_MAX             108
-#define G4X_M1_DISPLAY_PORT_MIN            0x10
-#define G4X_M1_DISPLAY_PORT_MAX            0x12
-#define G4X_M2_DISPLAY_PORT_MIN            0x05
-#define G4X_M2_DISPLAY_PORT_MAX            0x06
-#define G4X_P_DISPLAY_PORT_MIN             10
-#define G4X_P_DISPLAY_PORT_MAX             20
-#define G4X_P1_DISPLAY_PORT_MIN            1
-#define G4X_P1_DISPLAY_PORT_MAX            2
-#define G4X_P2_DISPLAY_PORT_SLOW           10
-#define G4X_P2_DISPLAY_PORT_FAST           10
-#define G4X_P2_DISPLAY_PORT_LIMIT          0
-
-/* Ironlake / Sandybridge */
-/* as we calculate clock using (register_value + 2) for
-   N/M1/M2, so here the range value for them is (actual_value-2).
- */
-#define IRONLAKE_DOT_MIN         25000
-#define IRONLAKE_DOT_MAX         350000
-#define IRONLAKE_VCO_MIN         1760000
-#define IRONLAKE_VCO_MAX         3510000
-#define IRONLAKE_M1_MIN          12
-#define IRONLAKE_M1_MAX          22
-#define IRONLAKE_M2_MIN          5
-#define IRONLAKE_M2_MAX          9
-#define IRONLAKE_P2_DOT_LIMIT    225000 /* 225Mhz */
-
-/* We have parameter ranges for different type of outputs. */
-
-/* DAC & HDMI Refclk 120Mhz */
-#define IRONLAKE_DAC_N_MIN	1
-#define IRONLAKE_DAC_N_MAX	5
-#define IRONLAKE_DAC_M_MIN	79
-#define IRONLAKE_DAC_M_MAX	127
-#define IRONLAKE_DAC_P_MIN	5
-#define IRONLAKE_DAC_P_MAX	80
-#define IRONLAKE_DAC_P1_MIN	1
-#define IRONLAKE_DAC_P1_MAX	8
-#define IRONLAKE_DAC_P2_SLOW	10
-#define IRONLAKE_DAC_P2_FAST	5
-
-/* LVDS single-channel 120Mhz refclk */
-#define IRONLAKE_LVDS_S_N_MIN	1
-#define IRONLAKE_LVDS_S_N_MAX	3
-#define IRONLAKE_LVDS_S_M_MIN	79
-#define IRONLAKE_LVDS_S_M_MAX	118
-#define IRONLAKE_LVDS_S_P_MIN	28
-#define IRONLAKE_LVDS_S_P_MAX	112
-#define IRONLAKE_LVDS_S_P1_MIN	2
-#define IRONLAKE_LVDS_S_P1_MAX	8
-#define IRONLAKE_LVDS_S_P2_SLOW	14
-#define IRONLAKE_LVDS_S_P2_FAST	14
-
-/* LVDS dual-channel 120Mhz refclk */
-#define IRONLAKE_LVDS_D_N_MIN	1
-#define IRONLAKE_LVDS_D_N_MAX	3
-#define IRONLAKE_LVDS_D_M_MIN	79
-#define IRONLAKE_LVDS_D_M_MAX	127
-#define IRONLAKE_LVDS_D_P_MIN	14
-#define IRONLAKE_LVDS_D_P_MAX	56
-#define IRONLAKE_LVDS_D_P1_MIN	2
-#define IRONLAKE_LVDS_D_P1_MAX	8
-#define IRONLAKE_LVDS_D_P2_SLOW	7
-#define IRONLAKE_LVDS_D_P2_FAST	7
-
-/* LVDS single-channel 100Mhz refclk */
-#define IRONLAKE_LVDS_S_SSC_N_MIN	1
-#define IRONLAKE_LVDS_S_SSC_N_MAX	2
-#define IRONLAKE_LVDS_S_SSC_M_MIN	79
-#define IRONLAKE_LVDS_S_SSC_M_MAX	126
-#define IRONLAKE_LVDS_S_SSC_P_MIN	28
-#define IRONLAKE_LVDS_S_SSC_P_MAX	112
-#define IRONLAKE_LVDS_S_SSC_P1_MIN	2
-#define IRONLAKE_LVDS_S_SSC_P1_MAX	8
-#define IRONLAKE_LVDS_S_SSC_P2_SLOW	14
-#define IRONLAKE_LVDS_S_SSC_P2_FAST	14
-
-/* LVDS dual-channel 100Mhz refclk */
-#define IRONLAKE_LVDS_D_SSC_N_MIN	1
-#define IRONLAKE_LVDS_D_SSC_N_MAX	3
-#define IRONLAKE_LVDS_D_SSC_M_MIN	79
-#define IRONLAKE_LVDS_D_SSC_M_MAX	126
-#define IRONLAKE_LVDS_D_SSC_P_MIN	14
-#define IRONLAKE_LVDS_D_SSC_P_MAX	42
-#define IRONLAKE_LVDS_D_SSC_P1_MIN	2
-#define IRONLAKE_LVDS_D_SSC_P1_MAX	6
-#define IRONLAKE_LVDS_D_SSC_P2_SLOW	7
-#define IRONLAKE_LVDS_D_SSC_P2_FAST	7
-
-/* DisplayPort */
-#define IRONLAKE_DP_N_MIN		1
-#define IRONLAKE_DP_N_MAX		2
-#define IRONLAKE_DP_M_MIN		81
-#define IRONLAKE_DP_M_MAX		90
-#define IRONLAKE_DP_P_MIN		10
-#define IRONLAKE_DP_P_MAX		20
-#define IRONLAKE_DP_P2_FAST		10
-#define IRONLAKE_DP_P2_SLOW		10
-#define IRONLAKE_DP_P2_LIMIT		0
-#define IRONLAKE_DP_P1_MIN		1
-#define IRONLAKE_DP_P1_MAX		2
-
 /* FDI */
 #define IRONLAKE_FDI_FREQ		2700000 /* in kHz for mode->clock */
 
@@ -353,292 +104,253 @@ intel_fdi_link_freq(struct drm_device *dev)
 }
 
 static const intel_limit_t intel_limits_i8xx_dvo = {
-        .dot = { .min = I8XX_DOT_MIN,		.max = I8XX_DOT_MAX },
-        .vco = { .min = I8XX_VCO_MIN,		.max = I8XX_VCO_MAX },
-        .n   = { .min = I8XX_N_MIN,		.max = I8XX_N_MAX },
-        .m   = { .min = I8XX_M_MIN,		.max = I8XX_M_MAX },
-        .m1  = { .min = I8XX_M1_MIN,		.max = I8XX_M1_MAX },
-        .m2  = { .min = I8XX_M2_MIN,		.max = I8XX_M2_MAX },
-        .p   = { .min = I8XX_P_MIN,		.max = I8XX_P_MAX },
-        .p1  = { .min = I8XX_P1_MIN,		.max = I8XX_P1_MAX },
-	.p2  = { .dot_limit = I8XX_P2_SLOW_LIMIT,
-		 .p2_slow = I8XX_P2_SLOW,	.p2_fast = I8XX_P2_FAST },
+        .dot = { .min = 25000, .max = 350000 },
+        .vco = { .min = 930000, .max = 1400000 },
+        .n = { .min = 3, .max = 16 },
+        .m = { .min = 96, .max = 140 },
+        .m1 = { .min = 18, .max = 26 },
+        .m2 = { .min = 6, .max = 16 },
+        .p = { .min = 4, .max = 128 },
+        .p1 = { .min = 2, .max = 33 },
+	.p2 = { .dot_limit = 165000,
+		.p2_slow = 4, .p2_fast = 2 },
 	.find_pll = intel_find_best_PLL,
 };
 
 static const intel_limit_t intel_limits_i8xx_lvds = {
-        .dot = { .min = I8XX_DOT_MIN,		.max = I8XX_DOT_MAX },
-        .vco = { .min = I8XX_VCO_MIN,		.max = I8XX_VCO_MAX },
-        .n   = { .min = I8XX_N_MIN,		.max = I8XX_N_MAX },
-        .m   = { .min = I8XX_M_MIN,		.max = I8XX_M_MAX },
-        .m1  = { .min = I8XX_M1_MIN,		.max = I8XX_M1_MAX },
-        .m2  = { .min = I8XX_M2_MIN,		.max = I8XX_M2_MAX },
-        .p   = { .min = I8XX_P_MIN,		.max = I8XX_P_MAX },
-        .p1  = { .min = I8XX_P1_LVDS_MIN,	.max = I8XX_P1_LVDS_MAX },
-	.p2  = { .dot_limit = I8XX_P2_SLOW_LIMIT,
-		 .p2_slow = I8XX_P2_LVDS_SLOW,	.p2_fast = I8XX_P2_LVDS_FAST },
+        .dot = { .min = 25000, .max = 350000 },
+        .vco = { .min = 930000, .max = 1400000 },
+        .n = { .min = 3, .max = 16 },
+        .m = { .min = 96, .max = 140 },
+        .m1 = { .min = 18, .max = 26 },
+        .m2 = { .min = 6, .max = 16 },
+        .p = { .min = 4, .max = 128 },
+        .p1 = { .min = 1, .max = 6 },
+	.p2 = { .dot_limit = 165000,
+		.p2_slow = 14, .p2_fast = 7 },
 	.find_pll = intel_find_best_PLL,
 };
-	
+
 static const intel_limit_t intel_limits_i9xx_sdvo = {
-        .dot = { .min = I9XX_DOT_MIN,		.max = I9XX_DOT_MAX },
-        .vco = { .min = I9XX_VCO_MIN,		.max = I9XX_VCO_MAX },
-        .n   = { .min = I9XX_N_MIN,		.max = I9XX_N_MAX },
-        .m   = { .min = I9XX_M_MIN,		.max = I9XX_M_MAX },
-        .m1  = { .min = I9XX_M1_MIN,		.max = I9XX_M1_MAX },
-        .m2  = { .min = I9XX_M2_MIN,		.max = I9XX_M2_MAX },
-        .p   = { .min = I9XX_P_SDVO_DAC_MIN,	.max = I9XX_P_SDVO_DAC_MAX },
-        .p1  = { .min = I9XX_P1_MIN,		.max = I9XX_P1_MAX },
-	.p2  = { .dot_limit = I9XX_P2_SDVO_DAC_SLOW_LIMIT,
-		 .p2_slow = I9XX_P2_SDVO_DAC_SLOW,	.p2_fast = I9XX_P2_SDVO_DAC_FAST },
+        .dot = { .min = 20000, .max = 400000 },
+        .vco = { .min = 1400000, .max = 2800000 },
+        .n = { .min = 1, .max = 6 },
+        .m = { .min = 70, .max = 120 },
+        .m1 = { .min = 10, .max = 22 },
+        .m2 = { .min = 5, .max = 9 },
+        .p = { .min = 5, .max = 80 },
+        .p1 = { .min = 1, .max = 8 },
+	.p2 = { .dot_limit = 200000,
+		.p2_slow = 10, .p2_fast = 5 },
 	.find_pll = intel_find_best_PLL,
 };
 
 static const intel_limit_t intel_limits_i9xx_lvds = {
-        .dot = { .min = I9XX_DOT_MIN,		.max = I9XX_DOT_MAX },
-        .vco = { .min = I9XX_VCO_MIN,		.max = I9XX_VCO_MAX },
-        .n   = { .min = I9XX_N_MIN,		.max = I9XX_N_MAX },
-        .m   = { .min = I9XX_M_MIN,		.max = I9XX_M_MAX },
-        .m1  = { .min = I9XX_M1_MIN,		.max = I9XX_M1_MAX },
-        .m2  = { .min = I9XX_M2_MIN,		.max = I9XX_M2_MAX },
-        .p   = { .min = I9XX_P_LVDS_MIN,	.max = I9XX_P_LVDS_MAX },
-        .p1  = { .min = I9XX_P1_MIN,		.max = I9XX_P1_MAX },
-	/* The single-channel range is 25-112Mhz, and dual-channel
-	 * is 80-224Mhz.  Prefer single channel as much as possible.
-	 */
-	.p2  = { .dot_limit = I9XX_P2_LVDS_SLOW_LIMIT,
-		 .p2_slow = I9XX_P2_LVDS_SLOW,	.p2_fast = I9XX_P2_LVDS_FAST },
+        .dot = { .min = 20000, .max = 400000 },
+        .vco = { .min = 1400000, .max = 2800000 },
+        .n = { .min = 1, .max = 6 },
+        .m = { .min = 70, .max = 120 },
+        .m1 = { .min = 10, .max = 22 },
+        .m2 = { .min = 5, .max = 9 },
+        .p = { .min = 7, .max = 98 },
+        .p1 = { .min = 1, .max = 8 },
+	.p2 = { .dot_limit = 112000,
+		.p2_slow = 14, .p2_fast = 7 },
 	.find_pll = intel_find_best_PLL,
 };
 
-    /* below parameter and function is for G4X Chipset Family*/
+
 static const intel_limit_t intel_limits_g4x_sdvo = {
-	.dot = { .min = G4X_DOT_SDVO_MIN,	.max = G4X_DOT_SDVO_MAX },
-	.vco = { .min = G4X_VCO_MIN,	        .max = G4X_VCO_MAX},
-	.n   = { .min = G4X_N_SDVO_MIN,	        .max = G4X_N_SDVO_MAX },
-	.m   = { .min = G4X_M_SDVO_MIN,         .max = G4X_M_SDVO_MAX },
-	.m1  = { .min = G4X_M1_SDVO_MIN,	.max = G4X_M1_SDVO_MAX },
-	.m2  = { .min = G4X_M2_SDVO_MIN,	.max = G4X_M2_SDVO_MAX },
-	.p   = { .min = G4X_P_SDVO_MIN,         .max = G4X_P_SDVO_MAX },
-	.p1  = { .min = G4X_P1_SDVO_MIN,	.max = G4X_P1_SDVO_MAX},
-	.p2  = { .dot_limit = G4X_P2_SDVO_LIMIT,
-		 .p2_slow = G4X_P2_SDVO_SLOW,
-		 .p2_fast = G4X_P2_SDVO_FAST
+	.dot = { .min = 25000, .max = 270000 },
+	.vco = { .min = 1750000, .max = 3500000},
+	.n = { .min = 1, .max = 4 },
+	.m = { .min = 104, .max = 138 },
+	.m1 = { .min = 17, .max = 23 },
+	.m2 = { .min = 5, .max = 11 },
+	.p = { .min = 10, .max = 30 },
+	.p1 = { .min = 1, .max = 3},
+	.p2 = { .dot_limit = 270000,
+		.p2_slow = 10,
+		.p2_fast = 10
 	},
 	.find_pll = intel_g4x_find_best_PLL,
 };
 
 static const intel_limit_t intel_limits_g4x_hdmi = {
-	.dot = { .min = G4X_DOT_HDMI_DAC_MIN,	.max = G4X_DOT_HDMI_DAC_MAX },
-	.vco = { .min = G4X_VCO_MIN,	        .max = G4X_VCO_MAX},
-	.n   = { .min = G4X_N_HDMI_DAC_MIN,	.max = G4X_N_HDMI_DAC_MAX },
-	.m   = { .min = G4X_M_HDMI_DAC_MIN,	.max = G4X_M_HDMI_DAC_MAX },
-	.m1  = { .min = G4X_M1_HDMI_DAC_MIN,	.max = G4X_M1_HDMI_DAC_MAX },
-	.m2  = { .min = G4X_M2_HDMI_DAC_MIN,	.max = G4X_M2_HDMI_DAC_MAX },
-	.p   = { .min = G4X_P_HDMI_DAC_MIN,	.max = G4X_P_HDMI_DAC_MAX },
-	.p1  = { .min = G4X_P1_HDMI_DAC_MIN,	.max = G4X_P1_HDMI_DAC_MAX},
-	.p2  = { .dot_limit = G4X_P2_HDMI_DAC_LIMIT,
-		 .p2_slow = G4X_P2_HDMI_DAC_SLOW,
-		 .p2_fast = G4X_P2_HDMI_DAC_FAST
-	},
+	.dot = { .min = 22000, .max = 400000 },
+	.vco = { .min = 1750000, .max = 3500000},
+	.n = { .min = 1, .max = 4 },
+	.m = { .min = 104, .max = 138 },
+	.m1 = { .min = 16, .max = 23 },
+	.m2 = { .min = 5, .max = 11 },
+	.p = { .min = 5, .max = 80 },
+	.p1 = { .min = 1, .max = 8},
+	.p2 = { .dot_limit = 165000,
+		.p2_slow = 10, .p2_fast = 5 },
 	.find_pll = intel_g4x_find_best_PLL,
 };
 
 static const intel_limit_t intel_limits_g4x_single_channel_lvds = {
-	.dot = { .min = G4X_DOT_SINGLE_CHANNEL_LVDS_MIN,
-		 .max = G4X_DOT_SINGLE_CHANNEL_LVDS_MAX },
-	.vco = { .min = G4X_VCO_MIN,
-		 .max = G4X_VCO_MAX },
-	.n   = { .min = G4X_N_SINGLE_CHANNEL_LVDS_MIN,
-		 .max = G4X_N_SINGLE_CHANNEL_LVDS_MAX },
-	.m   = { .min = G4X_M_SINGLE_CHANNEL_LVDS_MIN,
-		 .max = G4X_M_SINGLE_CHANNEL_LVDS_MAX },
-	.m1  = { .min = G4X_M1_SINGLE_CHANNEL_LVDS_MIN,
-		 .max = G4X_M1_SINGLE_CHANNEL_LVDS_MAX },
-	.m2  = { .min = G4X_M2_SINGLE_CHANNEL_LVDS_MIN,
-		 .max = G4X_M2_SINGLE_CHANNEL_LVDS_MAX },
-	.p   = { .min = G4X_P_SINGLE_CHANNEL_LVDS_MIN,
-		 .max = G4X_P_SINGLE_CHANNEL_LVDS_MAX },
-	.p1  = { .min = G4X_P1_SINGLE_CHANNEL_LVDS_MIN,
-		 .max = G4X_P1_SINGLE_CHANNEL_LVDS_MAX },
-	.p2  = { .dot_limit = G4X_P2_SINGLE_CHANNEL_LVDS_LIMIT,
-		 .p2_slow = G4X_P2_SINGLE_CHANNEL_LVDS_SLOW,
-		 .p2_fast = G4X_P2_SINGLE_CHANNEL_LVDS_FAST
+	.dot = { .min = 20000, .max = 115000 },
+	.vco = { .min = 1750000, .max = 3500000 },
+	.n = { .min = 1, .max = 3 },
+	.m = { .min = 104, .max = 138 },
+	.m1 = { .min = 17, .max = 23 },
+	.m2 = { .min = 5, .max = 11 },
+	.p = { .min = 28, .max = 112 },
+	.p1 = { .min = 2, .max = 8 },
+	.p2 = { .dot_limit = 0,
+		.p2_slow = 14, .p2_fast = 14
 	},
 	.find_pll = intel_g4x_find_best_PLL,
 };
 
 static const intel_limit_t intel_limits_g4x_dual_channel_lvds = {
-	.dot = { .min = G4X_DOT_DUAL_CHANNEL_LVDS_MIN,
-		 .max = G4X_DOT_DUAL_CHANNEL_LVDS_MAX },
-	.vco = { .min = G4X_VCO_MIN,
-		 .max = G4X_VCO_MAX },
-	.n   = { .min = G4X_N_DUAL_CHANNEL_LVDS_MIN,
-		 .max = G4X_N_DUAL_CHANNEL_LVDS_MAX },
-	.m   = { .min = G4X_M_DUAL_CHANNEL_LVDS_MIN,
-		 .max = G4X_M_DUAL_CHANNEL_LVDS_MAX },
-	.m1  = { .min = G4X_M1_DUAL_CHANNEL_LVDS_MIN,
-		 .max = G4X_M1_DUAL_CHANNEL_LVDS_MAX },
-	.m2  = { .min = G4X_M2_DUAL_CHANNEL_LVDS_MIN,
-		 .max = G4X_M2_DUAL_CHANNEL_LVDS_MAX },
-	.p   = { .min = G4X_P_DUAL_CHANNEL_LVDS_MIN,
-		 .max = G4X_P_DUAL_CHANNEL_LVDS_MAX },
-	.p1  = { .min = G4X_P1_DUAL_CHANNEL_LVDS_MIN,
-		 .max = G4X_P1_DUAL_CHANNEL_LVDS_MAX },
-	.p2  = { .dot_limit = G4X_P2_DUAL_CHANNEL_LVDS_LIMIT,
-		 .p2_slow = G4X_P2_DUAL_CHANNEL_LVDS_SLOW,
-		 .p2_fast = G4X_P2_DUAL_CHANNEL_LVDS_FAST
+	.dot = { .min = 80000, .max = 224000 },
+	.vco = { .min = 1750000, .max = 3500000 },
+	.n = { .min = 1, .max = 3 },
+	.m = { .min = 104, .max = 138 },
+	.m1 = { .min = 17, .max = 23 },
+	.m2 = { .min = 5, .max = 11 },
+	.p = { .min = 14, .max = 42 },
+	.p1 = { .min = 2, .max = 6 },
+	.p2 = { .dot_limit = 0,
+		.p2_slow = 7, .p2_fast = 7
 	},
 	.find_pll = intel_g4x_find_best_PLL,
 };
 
 static const intel_limit_t intel_limits_g4x_display_port = {
-        .dot = { .min = G4X_DOT_DISPLAY_PORT_MIN,
-                 .max = G4X_DOT_DISPLAY_PORT_MAX },
-        .vco = { .min = G4X_VCO_MIN,
-                 .max = G4X_VCO_MAX},
-        .n   = { .min = G4X_N_DISPLAY_PORT_MIN,
-                 .max = G4X_N_DISPLAY_PORT_MAX },
-        .m   = { .min = G4X_M_DISPLAY_PORT_MIN,
-                 .max = G4X_M_DISPLAY_PORT_MAX },
-        .m1  = { .min = G4X_M1_DISPLAY_PORT_MIN,
-                 .max = G4X_M1_DISPLAY_PORT_MAX },
-        .m2  = { .min = G4X_M2_DISPLAY_PORT_MIN,
-                 .max = G4X_M2_DISPLAY_PORT_MAX },
-        .p   = { .min = G4X_P_DISPLAY_PORT_MIN,
-                 .max = G4X_P_DISPLAY_PORT_MAX },
-        .p1  = { .min = G4X_P1_DISPLAY_PORT_MIN,
-                 .max = G4X_P1_DISPLAY_PORT_MAX},
-        .p2  = { .dot_limit = G4X_P2_DISPLAY_PORT_LIMIT,
-                 .p2_slow = G4X_P2_DISPLAY_PORT_SLOW,
-                 .p2_fast = G4X_P2_DISPLAY_PORT_FAST },
+        .dot = { .min = 161670, .max = 227000 },
+        .vco = { .min = 1750000, .max = 3500000},
+        .n = { .min = 1, .max = 2 },
+        .m = { .min = 97, .max = 108 },
+        .m1 = { .min = 0x10, .max = 0x12 },
+        .m2 = { .min = 0x05, .max = 0x06 },
+        .p = { .min = 10, .max = 20 },
+        .p1 = { .min = 1, .max = 2},
+        .p2 = { .dot_limit = 0,
+		.p2_slow = 10, .p2_fast = 10 },
         .find_pll = intel_find_pll_g4x_dp,
 };
 
 static const intel_limit_t intel_limits_pineview_sdvo = {
-        .dot = { .min = I9XX_DOT_MIN,		.max = I9XX_DOT_MAX},
-        .vco = { .min = PINEVIEW_VCO_MIN,		.max = PINEVIEW_VCO_MAX },
-        .n   = { .min = PINEVIEW_N_MIN,		.max = PINEVIEW_N_MAX },
-        .m   = { .min = PINEVIEW_M_MIN,		.max = PINEVIEW_M_MAX },
-        .m1  = { .min = PINEVIEW_M1_MIN,		.max = PINEVIEW_M1_MAX },
-        .m2  = { .min = PINEVIEW_M2_MIN,		.max = PINEVIEW_M2_MAX },
-        .p   = { .min = I9XX_P_SDVO_DAC_MIN,    .max = I9XX_P_SDVO_DAC_MAX },
-        .p1  = { .min = I9XX_P1_MIN,		.max = I9XX_P1_MAX },
-	.p2  = { .dot_limit = I9XX_P2_SDVO_DAC_SLOW_LIMIT,
-		 .p2_slow = I9XX_P2_SDVO_DAC_SLOW,	.p2_fast = I9XX_P2_SDVO_DAC_FAST },
+        .dot = { .min = 20000, .max = 400000},
+        .vco = { .min = 1700000, .max = 3500000 },
+	/* Pineview's Ncounter is a ring counter */
+        .n = { .min = 3, .max = 6 },
+        .m = { .min = 2, .max = 256 },
+	/* Pineview only has one combined m divider, which we treat as m2. */
+        .m1 = { .min = 0, .max = 0 },
+        .m2 = { .min = 0, .max = 254 },
+        .p = { .min = 5, .max = 80 },
+        .p1 = { .min = 1, .max = 8 },
+	.p2 = { .dot_limit = 200000,
+		.p2_slow = 10, .p2_fast = 5 },
 	.find_pll = intel_find_best_PLL,
 };
 
 static const intel_limit_t intel_limits_pineview_lvds = {
-        .dot = { .min = I9XX_DOT_MIN,		.max = I9XX_DOT_MAX },
-        .vco = { .min = PINEVIEW_VCO_MIN,		.max = PINEVIEW_VCO_MAX },
-        .n   = { .min = PINEVIEW_N_MIN,		.max = PINEVIEW_N_MAX },
-        .m   = { .min = PINEVIEW_M_MIN,		.max = PINEVIEW_M_MAX },
-        .m1  = { .min = PINEVIEW_M1_MIN,		.max = PINEVIEW_M1_MAX },
-        .m2  = { .min = PINEVIEW_M2_MIN,		.max = PINEVIEW_M2_MAX },
-        .p   = { .min = PINEVIEW_P_LVDS_MIN,	.max = PINEVIEW_P_LVDS_MAX },
-        .p1  = { .min = I9XX_P1_MIN,		.max = I9XX_P1_MAX },
-	/* Pineview only supports single-channel mode. */
-	.p2  = { .dot_limit = I9XX_P2_LVDS_SLOW_LIMIT,
-		 .p2_slow = I9XX_P2_LVDS_SLOW,	.p2_fast = I9XX_P2_LVDS_SLOW },
+        .dot = { .min = 20000, .max = 400000 },
+        .vco = { .min = 1700000, .max = 3500000 },
+        .n = { .min = 3, .max = 6 },
+        .m = { .min = 2, .max = 256 },
+        .m1 = { .min = 0, .max = 0 },
+        .m2 = { .min = 0, .max = 254 },
+        .p = { .min = 7, .max = 112 },
+        .p1 = { .min = 1, .max = 8 },
+	.p2 = { .dot_limit = 112000,
+		.p2_slow = 14, .p2_fast = 14 },
 	.find_pll = intel_find_best_PLL,
 };
 
+/* Ironlake / Sandybridge
+ *
+ * We calculate clock using (register_value + 2) for N/M1/M2, so here
+ * the range value for them is (actual_value - 2).
+ */
 static const intel_limit_t intel_limits_ironlake_dac = {
-	.dot = { .min = IRONLAKE_DOT_MIN,          .max = IRONLAKE_DOT_MAX },
-	.vco = { .min = IRONLAKE_VCO_MIN,          .max = IRONLAKE_VCO_MAX },
-	.n   = { .min = IRONLAKE_DAC_N_MIN,        .max = IRONLAKE_DAC_N_MAX },
-	.m   = { .min = IRONLAKE_DAC_M_MIN,        .max = IRONLAKE_DAC_M_MAX },
-	.m1  = { .min = IRONLAKE_M1_MIN,           .max = IRONLAKE_M1_MAX },
-	.m2  = { .min = IRONLAKE_M2_MIN,           .max = IRONLAKE_M2_MAX },
-	.p   = { .min = IRONLAKE_DAC_P_MIN,	   .max = IRONLAKE_DAC_P_MAX },
-	.p1  = { .min = IRONLAKE_DAC_P1_MIN,       .max = IRONLAKE_DAC_P1_MAX },
-	.p2  = { .dot_limit = IRONLAKE_P2_DOT_LIMIT,
-		 .p2_slow = IRONLAKE_DAC_P2_SLOW,
-		 .p2_fast = IRONLAKE_DAC_P2_FAST },
+	.dot = { .min = 25000, .max = 350000 },
+	.vco = { .min = 1760000, .max = 3510000 },
+	.n = { .min = 1, .max = 5 },
+	.m = { .min = 79, .max = 127 },
+	.m1 = { .min = 12, .max = 22 },
+	.m2 = { .min = 5, .max = 9 },
+	.p = { .min = 5, .max = 80 },
+	.p1 = { .min = 1, .max = 8 },
+	.p2 = { .dot_limit = 225000,
+		.p2_slow = 10, .p2_fast = 5 },
 	.find_pll = intel_g4x_find_best_PLL,
 };
 
 static const intel_limit_t intel_limits_ironlake_single_lvds = {
-	.dot = { .min = IRONLAKE_DOT_MIN,          .max = IRONLAKE_DOT_MAX },
-	.vco = { .min = IRONLAKE_VCO_MIN,          .max = IRONLAKE_VCO_MAX },
-	.n   = { .min = IRONLAKE_LVDS_S_N_MIN,     .max = IRONLAKE_LVDS_S_N_MAX },
-	.m   = { .min = IRONLAKE_LVDS_S_M_MIN,     .max = IRONLAKE_LVDS_S_M_MAX },
-	.m1  = { .min = IRONLAKE_M1_MIN,           .max = IRONLAKE_M1_MAX },
-	.m2  = { .min = IRONLAKE_M2_MIN,           .max = IRONLAKE_M2_MAX },
-	.p   = { .min = IRONLAKE_LVDS_S_P_MIN,     .max = IRONLAKE_LVDS_S_P_MAX },
-	.p1  = { .min = IRONLAKE_LVDS_S_P1_MIN,    .max = IRONLAKE_LVDS_S_P1_MAX },
-	.p2  = { .dot_limit = IRONLAKE_P2_DOT_LIMIT,
-		 .p2_slow = IRONLAKE_LVDS_S_P2_SLOW,
-		 .p2_fast = IRONLAKE_LVDS_S_P2_FAST },
+	.dot = { .min = 25000, .max = 350000 },
+	.vco = { .min = 1760000, .max = 3510000 },
+	.n = { .min = 1, .max = 3 },
+	.m = { .min = 79, .max = 118 },
+	.m1 = { .min = 12, .max = 22 },
+	.m2 = { .min = 5, .max = 9 },
+	.p = { .min = 28, .max = 112 },
+	.p1 = { .min = 2, .max = 8 },
+	.p2 = { .dot_limit = 225000,
+		.p2_slow = 14, .p2_fast = 14 },
 	.find_pll = intel_g4x_find_best_PLL,
 };
 
 static const intel_limit_t intel_limits_ironlake_dual_lvds = {
-	.dot = { .min = IRONLAKE_DOT_MIN,          .max = IRONLAKE_DOT_MAX },
-	.vco = { .min = IRONLAKE_VCO_MIN,          .max = IRONLAKE_VCO_MAX },
-	.n   = { .min = IRONLAKE_LVDS_D_N_MIN,     .max = IRONLAKE_LVDS_D_N_MAX },
-	.m   = { .min = IRONLAKE_LVDS_D_M_MIN,     .max = IRONLAKE_LVDS_D_M_MAX },
-	.m1  = { .min = IRONLAKE_M1_MIN,           .max = IRONLAKE_M1_MAX },
-	.m2  = { .min = IRONLAKE_M2_MIN,           .max = IRONLAKE_M2_MAX },
-	.p   = { .min = IRONLAKE_LVDS_D_P_MIN,     .max = IRONLAKE_LVDS_D_P_MAX },
-	.p1  = { .min = IRONLAKE_LVDS_D_P1_MIN,    .max = IRONLAKE_LVDS_D_P1_MAX },
-	.p2  = { .dot_limit = IRONLAKE_P2_DOT_LIMIT,
-		 .p2_slow = IRONLAKE_LVDS_D_P2_SLOW,
-		 .p2_fast = IRONLAKE_LVDS_D_P2_FAST },
+	.dot = { .min = 25000, .max = 350000 },
+	.vco = { .min = 1760000, .max = 3510000 },
+	.n = { .min = 1, .max = 3 },
+	.m = { .min = 79, .max = 127 },
+	.m1 = { .min = 12, .max = 22 },
+	.m2 = { .min = 5, .max = 9 },
+	.p = { .min = 14, .max = 56 },
+	.p1 = { .min = 2, .max = 8 },
+	.p2 = { .dot_limit = 225000,
+		.p2_slow = 7, .p2_fast = 7 },
 	.find_pll = intel_g4x_find_best_PLL,
 };
 
+/* LVDS 100mhz refclk limits. */
 static const intel_limit_t intel_limits_ironlake_single_lvds_100m = {
-	.dot = { .min = IRONLAKE_DOT_MIN,          .max = IRONLAKE_DOT_MAX },
-	.vco = { .min = IRONLAKE_VCO_MIN,          .max = IRONLAKE_VCO_MAX },
-	.n   = { .min = IRONLAKE_LVDS_S_SSC_N_MIN, .max = IRONLAKE_LVDS_S_SSC_N_MAX },
-	.m   = { .min = IRONLAKE_LVDS_S_SSC_M_MIN, .max = IRONLAKE_LVDS_S_SSC_M_MAX },
-	.m1  = { .min = IRONLAKE_M1_MIN,           .max = IRONLAKE_M1_MAX },
-	.m2  = { .min = IRONLAKE_M2_MIN,           .max = IRONLAKE_M2_MAX },
-	.p   = { .min = IRONLAKE_LVDS_S_SSC_P_MIN, .max = IRONLAKE_LVDS_S_SSC_P_MAX },
-	.p1  = { .min = IRONLAKE_LVDS_S_SSC_P1_MIN,.max = IRONLAKE_LVDS_S_SSC_P1_MAX },
-	.p2  = { .dot_limit = IRONLAKE_P2_DOT_LIMIT,
-		 .p2_slow = IRONLAKE_LVDS_S_SSC_P2_SLOW,
-		 .p2_fast = IRONLAKE_LVDS_S_SSC_P2_FAST },
+	.dot = { .min = 25000, .max = 350000 },
+	.vco = { .min = 1760000, .max = 3510000 },
+	.n = { .min = 1, .max = 2 },
+	.m = { .min = 79, .max = 126 },
+	.m1 = { .min = 12, .max = 22 },
+	.m2 = { .min = 5, .max = 9 },
+	.p = { .min = 28, .max = 112 },
+	.p1 = { .min = 2,.max = 8 },
+	.p2 = { .dot_limit = 225000,
+		.p2_slow = 14, .p2_fast = 14 },
 	.find_pll = intel_g4x_find_best_PLL,
 };
 
 static const intel_limit_t intel_limits_ironlake_dual_lvds_100m = {
-	.dot = { .min = IRONLAKE_DOT_MIN,          .max = IRONLAKE_DOT_MAX },
-	.vco = { .min = IRONLAKE_VCO_MIN,          .max = IRONLAKE_VCO_MAX },
-	.n   = { .min = IRONLAKE_LVDS_D_SSC_N_MIN, .max = IRONLAKE_LVDS_D_SSC_N_MAX },
-	.m   = { .min = IRONLAKE_LVDS_D_SSC_M_MIN, .max = IRONLAKE_LVDS_D_SSC_M_MAX },
-	.m1  = { .min = IRONLAKE_M1_MIN,           .max = IRONLAKE_M1_MAX },
-	.m2  = { .min = IRONLAKE_M2_MIN,           .max = IRONLAKE_M2_MAX },
-	.p   = { .min = IRONLAKE_LVDS_D_SSC_P_MIN, .max = IRONLAKE_LVDS_D_SSC_P_MAX },
-	.p1  = { .min = IRONLAKE_LVDS_D_SSC_P1_MIN,.max = IRONLAKE_LVDS_D_SSC_P1_MAX },
-	.p2  = { .dot_limit = IRONLAKE_P2_DOT_LIMIT,
-		 .p2_slow = IRONLAKE_LVDS_D_SSC_P2_SLOW,
-		 .p2_fast = IRONLAKE_LVDS_D_SSC_P2_FAST },
+	.dot = { .min = 25000, .max = 350000 },
+	.vco = { .min = 1760000, .max = 3510000 },
+	.n = { .min = 1, .max = 3 },
+	.m = { .min = 79, .max = 126 },
+	.m1 = { .min = 12, .max = 22 },
+	.m2 = { .min = 5, .max = 9 },
+	.p = { .min = 14, .max = 42 },
+	.p1 = { .min = 2,.max = 6 },
+	.p2 = { .dot_limit = 225000,
+		.p2_slow = 7, .p2_fast = 7 },
 	.find_pll = intel_g4x_find_best_PLL,
 };
 
 static const intel_limit_t intel_limits_ironlake_display_port = {
-        .dot = { .min = IRONLAKE_DOT_MIN,
-                 .max = IRONLAKE_DOT_MAX },
-        .vco = { .min = IRONLAKE_VCO_MIN,
-                 .max = IRONLAKE_VCO_MAX},
-        .n   = { .min = IRONLAKE_DP_N_MIN,
-                 .max = IRONLAKE_DP_N_MAX },
-        .m   = { .min = IRONLAKE_DP_M_MIN,
-                 .max = IRONLAKE_DP_M_MAX },
-        .m1  = { .min = IRONLAKE_M1_MIN,
-                 .max = IRONLAKE_M1_MAX },
-        .m2  = { .min = IRONLAKE_M2_MIN,
-                 .max = IRONLAKE_M2_MAX },
-        .p   = { .min = IRONLAKE_DP_P_MIN,
-                 .max = IRONLAKE_DP_P_MAX },
-        .p1  = { .min = IRONLAKE_DP_P1_MIN,
-                 .max = IRONLAKE_DP_P1_MAX},
-        .p2  = { .dot_limit = IRONLAKE_DP_P2_LIMIT,
-                 .p2_slow = IRONLAKE_DP_P2_SLOW,
-                 .p2_fast = IRONLAKE_DP_P2_FAST },
+        .dot = { .min = 25000, .max = 350000 },
+        .vco = { .min = 1760000, .max = 3510000},
+        .n = { .min = 1, .max = 2 },
+        .m = { .min = 81, .max = 90 },
+        .m1 = { .min = 12, .max = 22 },
+        .m2 = { .min = 5, .max = 9 },
+        .p = { .min = 10, .max = 20 },
+        .p1 = { .min = 1, .max = 2},
+        .p2 = { .dot_limit = 0,
+		.p2_slow = 10, .p2_fast = 10 },
         .find_pll = intel_find_pll_ironlake_dp,
 };
 
Signature · 1 line
1.7.4.1
Acked-by on v1 9/9
#19 lore raw

Re: [PATCH 9/9] drm/i915: Fold the DPLL limit defines into the structs that use them.

Quoted 4 lines · On Wed, 30 Mar 2011 13:01:10 -0700 Eric Anholt <[email protected]> wrote:

They're used in one place, and not providing any descriptive value, with their names just being approximately the conjunction of the struct name and the struct field.

Quoted 8 lines

This diff was produced with gcc -E, copying the new struct definitions out, moving a couple of the old comments into place in the new structs, and reindenting.

---
 drivers/gpu/drm/i915/intel_display.c |  650 ++++++++++------------------------
 1 files changed, 181 insertions(+), 469 deletions(-)

Yes!

Signature · 1 line
Jesse Barnes, Intel Open Source Technology Center
#20 lore raw
In reply to Eric Anholt
Quoted 9 lines · Eric Anholt

In doing new chipset enablement for the first time in quite a while, it sunk in just how bad the spaghetti in our modeset path was these days. I think that splitting the crtc_mode_set up a bit gets us a more readable path for whichever generation you're trying to look at, while not duplicating too much code -- note that patch 1/9 is +675 LOC, while after 8/9 we're down to +299 overall.

To atone for about +300LOC, patch 9/9 does another cleanup I think is appropriate and cuts almost 300 lines of used-once #define spam.

No atonement necessary for cutting through the mountain of spaghetti. I'll throw this onto my collection of boxes and see if anything comes adrift. -Chris

Signature · 1 line
Chris Wilson, Intel Open Source Technology Centre